From: Zijun Hu <zijuhu@codeaurora.org>
To: marcel@holtmann.org, johan.hedberg@gmail.com
Cc: linux-kernel@vger.kernel.org, linux-bluetooth@vger.kernel.org,
linux-arm-msm@vger.kernel.org, bgodavar@codeaurora.org,
c-hbandi@codeaurora.org, hemantg@codeaurora.org,
mka@chromium.org, rjliao@codeaurora.org, zijuhu@codeaurora.org
Subject: [PATCH v2] Bluetooth: hci_qca: Fix qca6390 enable failure after warm reboot
Date: Fri, 29 May 2020 21:56:57 +0800 [thread overview]
Message-ID: <1590760617-30285-1-git-send-email-zijuhu@codeaurora.org> (raw)
Warm reboot can not reset controller qca6390 due to
lack of controllable power supply, so causes firmware
download failure during enable.
Fixed by sending VSC EDL_SOC_RESET to reset qca6390
within added device shutdown implementation.
Signed-off-by: Zijun Hu <zijuhu@codeaurora.org>
Tested-by: Zijun Hu <zijuhu@codeaurora.org>
---
Changes in v2:
- rebase
drivers/bluetooth/hci_qca.c | 33 +++++++++++++++++++++++++++++++++
1 file changed, 33 insertions(+)
diff --git a/drivers/bluetooth/hci_qca.c b/drivers/bluetooth/hci_qca.c
index adcbe00a2275..aa957d749d6f 100644
--- a/drivers/bluetooth/hci_qca.c
+++ b/drivers/bluetooth/hci_qca.c
@@ -1975,6 +1975,38 @@ static void qca_serdev_remove(struct serdev_device *serdev)
hci_uart_unregister_device(&qcadev->serdev_hu);
}
+static void qca_serdev_shutdown(struct device *dev)
+{
+ int ret;
+ int timeout = msecs_to_jiffies(CMD_TRANS_TIMEOUT_MS);
+ struct serdev_device *serdev = to_serdev_device(dev);
+ struct qca_serdev *qcadev = serdev_device_get_drvdata(serdev);
+ const u8 ibs_wake_cmd[] = { 0xFD };
+ const u8 edl_reset_soc_cmd[] = { 0x01, 0x00, 0xFC, 0x01, 0x05 };
+
+ if (qcadev->btsoc_type == QCA_QCA6390) {
+ serdev_device_write_flush(serdev);
+ ret = serdev_device_write_buf(serdev, ibs_wake_cmd,
+ sizeof(ibs_wake_cmd));
+ if (ret < 0) {
+ BT_ERR("QCA send IBS_WAKE_IND error: %d", ret);
+ return;
+ }
+ serdev_device_wait_until_sent(serdev, timeout);
+ usleep_range(8000, 10000);
+
+ serdev_device_write_flush(serdev);
+ ret = serdev_device_write_buf(serdev, edl_reset_soc_cmd,
+ sizeof(edl_reset_soc_cmd));
+ if (ret < 0) {
+ BT_ERR("QCA send EDL_RESET_REQ error: %d", ret);
+ return;
+ }
+ serdev_device_wait_until_sent(serdev, timeout);
+ usleep_range(8000, 10000);
+ }
+}
+
static int __maybe_unused qca_suspend(struct device *dev)
{
struct serdev_device *serdev = to_serdev_device(dev);
@@ -2102,6 +2134,7 @@ static struct serdev_device_driver qca_serdev_driver = {
.name = "hci_uart_qca",
.of_match_table = of_match_ptr(qca_bluetooth_of_match),
.acpi_match_table = ACPI_PTR(qca_bluetooth_acpi_match),
+ .shutdown = qca_serdev_shutdown,
.pm = &qca_pm_ops,
},
};
--
The Qualcomm Innovation Center, Inc. is a member of the Code Aurora Forum, a Linux Foundation Collaborative Project
next reply other threads:[~2020-05-29 13:57 UTC|newest]
Thread overview: 4+ messages / expand[flat|nested] mbox.gz Atom feed top
2020-05-29 13:56 Zijun Hu [this message]
2020-05-29 14:05 ` [PATCH v2] Bluetooth: hci_qca: Fix qca6390 enable failure after warm reboot Marcel Holtmann
-- strict thread matches above, loose matches on Subject: below --
2020-05-26 2:57 [PATCH v2] bluetooth: " Zijun Hu
2020-05-26 15:34 ` Matthias Kaehlcke
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=1590760617-30285-1-git-send-email-zijuhu@codeaurora.org \
--to=zijuhu@codeaurora.org \
--cc=bgodavar@codeaurora.org \
--cc=c-hbandi@codeaurora.org \
--cc=hemantg@codeaurora.org \
--cc=johan.hedberg@gmail.com \
--cc=linux-arm-msm@vger.kernel.org \
--cc=linux-bluetooth@vger.kernel.org \
--cc=linux-kernel@vger.kernel.org \
--cc=marcel@holtmann.org \
--cc=mka@chromium.org \
--cc=rjliao@codeaurora.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).