[PATCH v2 1/3] Bluetooth: btusb: mediatek: use readx_poll_timeout instead of open coding

* [PATCH v2 1/3] Bluetooth: btusb: mediatek: use readx_poll_timeout instead of open coding
@ 2022-09-30  0:23 sean.wang
  2022-09-30  0:23 ` [PATCH v2 2/3] Bluetooth: btmtk: introduce btmtk reset work sean.wang
                   ` (3 more replies)
  0 siblings, 4 replies; 9+ messages in thread
From: sean.wang @ 2022-09-30  0:23 UTC (permalink / raw)
  To: marcel, johan.hedberg, luiz.dentz
  Cc: sean.wang, Soul.Huang, YN.Chen, Leon.Yen, Eric-SY.Chang,
	Deren.Wu, km.lin, robin.chiu, Eddie.Chen, ch.yeh, posh.sun,
	ted.huang, Stella.Chang, Tom.Chou, steve.lee, jsiuda, frankgor,
	abhishekpandit, michaelfsun, abhishekpandit, mcchou, shawnku,
	linux-bluetooth, linux-mediatek, linux-kernel

From: Sean Wang <sean.wang@mediatek.com>

Use readx_poll_timeout instead of open coding to poll the hardware reset
status until it is done.

Signed-off-by: Sean Wang <sean.wang@mediatek.com>
---
The patch is built and tested on the top of the patches
[v6,1/3] Bluetooth: Add support for hci devcoredump
[v6,2/3] Bluetooth: btusb: Add btusb devcoredump support
[v6,3/3] Bluetooth: btintel: Add Intel devcoredump support
which are contributed from Manish Mandlik

v2: use 20ms as the unit to poll according to the requirement of
    readx_poll_timeout
---
 drivers/bluetooth/btusb.c | 32 ++++++++++++++++++--------------
 1 file changed, 18 insertions(+), 14 deletions(-)

diff --git a/drivers/bluetooth/btusb.c b/drivers/bluetooth/btusb.c
index 4eb79e88f1d9..9ef0dc648573 100644
--- a/drivers/bluetooth/btusb.c
+++ b/drivers/bluetooth/btusb.c
@@ -2361,8 +2361,6 @@ static int btusb_send_frame_intel(struct hci_dev *hdev, struct sk_buff *skb)
 #define MTK_EP_RST_OPT		0x74011890
 #define MTK_EP_RST_IN_OUT_OPT	0x00010001
 #define MTK_BT_RST_DONE		0x00000100
-#define MTK_BT_RESET_WAIT_MS	100
-#define MTK_BT_RESET_NUM_TRIES	10
 
 static void btusb_mtk_wmt_recv(struct urb *urb)
 {
@@ -2733,6 +2731,16 @@ static int btusb_mtk_id_get(struct btusb_data *data, u32 reg, u32 *id)
 	return btusb_mtk_reg_read(data, reg, id);
 }
 
+static u32 btusb_mtk_reset_done(struct hci_dev *hdev)
+{
+	struct btusb_data *data = hci_get_drvdata(hdev);
+	u32 val = 0;
+
+	btusb_mtk_uhw_reg_read(data, MTK_BT_MISC, &val);
+
+	return val;
+}
+
 static int btusb_mtk_setup(struct hci_dev *hdev)
 {
 	struct btusb_data *data = hci_get_drvdata(hdev);
@@ -2922,7 +2930,7 @@ static void btusb_mtk_cmd_timeout(struct hci_dev *hdev)
 {
 	struct btusb_data *data = hci_get_drvdata(hdev);
 	u32 val;
-	int err, retry = 0;
+	int err;
 
 	/* It's MediaTek specific bluetooth reset mechanism via USB */
 	if (test_and_set_bit(BTUSB_HW_RESET_ACTIVE, &data->flags)) {
@@ -2953,18 +2961,14 @@ static void btusb_mtk_cmd_timeout(struct hci_dev *hdev)
 	btusb_mtk_uhw_reg_write(data, MTK_BT_SUBSYS_RST, 0);
 	btusb_mtk_uhw_reg_read(data, MTK_BT_SUBSYS_RST, &val);
 
-	/* Poll the register until reset is completed */
-	do {
-		btusb_mtk_uhw_reg_read(data, MTK_BT_MISC, &val);
-		if (val & MTK_BT_RST_DONE) {
-			bt_dev_dbg(hdev, "Bluetooth Reset Successfully");
-			break;
-		}
+	err = readx_poll_timeout(btusb_mtk_reset_done, hdev, val,
+				 val & MTK_BT_RST_DONE,
+				 20000, 1000000);
+	if (err < 0)
+		bt_dev_err(hdev, "Reset timeout");
 
-		bt_dev_dbg(hdev, "Polling Bluetooth Reset CR");
-		retry++;
-		msleep(MTK_BT_RESET_WAIT_MS);
-	} while (retry < MTK_BT_RESET_NUM_TRIES);
+	if (val & MTK_BT_RST_DONE)
+		bt_dev_dbg(hdev, "Bluetooth Reset Successfully");
 
 	btusb_mtk_id_get(data, 0x70010200, &val);
 	if (!val)
-- 
2.25.1


^ permalink raw reply related	[flat|nested] 9+ messages in thread