* [PATCH v3 01/14] dt-bindings: sunxi: Add CCU binding documentation
2016-06-29 19:05 [PATCH v3 00/14] clk: sunxi: introduce "modern" clock support Maxime Ripard
@ 2016-06-29 19:05 ` Maxime Ripard
2016-07-01 2:17 ` Rob Herring
2016-06-29 19:05 ` [PATCH v3 02/14] clk: sunxi-ng: Add common infrastructure Maxime Ripard
` (12 subsequent siblings)
13 siblings, 1 reply; 22+ messages in thread
From: Maxime Ripard @ 2016-06-29 19:05 UTC (permalink / raw)
To: Mike Turquette, Stephen Boyd, Chen-Yu Tsai
Cc: linux-clk, Hans de Goede, Boris Brezillon, Rob Herring,
Vishnu Patekar, linux-arm-kernel, linux-kernel, devicetree,
Jean-Francois Moine, Maxime Ripard
Introduce a new binding with its documentation for the brand new clock
sub-framework.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
---
.../devicetree/bindings/clock/sunxi-ccu.txt | 24 ++++++++++++++++++++++
1 file changed, 24 insertions(+)
create mode 100644 Documentation/devicetree/bindings/clock/sunxi-ccu.txt
diff --git a/Documentation/devicetree/bindings/clock/sunxi-ccu.txt b/Documentation/devicetree/bindings/clock/sunxi-ccu.txt
new file mode 100644
index 000000000000..cb91507ffb1e
--- /dev/null
+++ b/Documentation/devicetree/bindings/clock/sunxi-ccu.txt
@@ -0,0 +1,24 @@
+Allwinner Clock Control Unit Binding
+------------------------------------
+
+Required properties :
+- compatible: must contain one of the following compatible:
+ - "allwinner,sun8i-h3-ccu"
+
+- reg: Must contain the registers base address and length
+- clocks: phandle to the oscillators feeding the CCU. Two are needed:
+ - "hosc": the high frequency oscillator (usually at 24MHz)
+ - "losc": the low frequency oscillator (usually at 32kHz)
+- clock-names: Must contain the clock names described just above
+- #clock-cells : must contain 1
+- #reset-cells : must contain 1
+
+Example:
+ccu: clock@01c20000 {
+ compatible = "allwinner,sun8i-h3-ccu";
+ reg = <0x01c20000 0x400>;
+ clocks = <&osc24M>, <&osc32k>;
+ clock-names = "hosc", "losc";
+ #clock-cells = <1>;
+ #reset-cells = <1>;
+};
--
2.9.0
^ permalink raw reply related [flat|nested] 22+ messages in thread
* Re: [PATCH v3 01/14] dt-bindings: sunxi: Add CCU binding documentation
2016-06-29 19:05 ` [PATCH v3 01/14] dt-bindings: sunxi: Add CCU binding documentation Maxime Ripard
@ 2016-07-01 2:17 ` Rob Herring
0 siblings, 0 replies; 22+ messages in thread
From: Rob Herring @ 2016-07-01 2:17 UTC (permalink / raw)
To: Maxime Ripard
Cc: Mike Turquette, Stephen Boyd, Chen-Yu Tsai, linux-clk,
Hans de Goede, Boris Brezillon, Vishnu Patekar, linux-arm-kernel,
linux-kernel, devicetree, Jean-Francois Moine
On Wed, Jun 29, 2016 at 09:05:22PM +0200, Maxime Ripard wrote:
> Introduce a new binding with its documentation for the brand new clock
> sub-framework.
>
> Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
> ---
> .../devicetree/bindings/clock/sunxi-ccu.txt | 24 ++++++++++++++++++++++
> 1 file changed, 24 insertions(+)
> create mode 100644 Documentation/devicetree/bindings/clock/sunxi-ccu.txt
Yay!
Acked-by: Rob Herring <robh@kernel.org>
^ permalink raw reply [flat|nested] 22+ messages in thread
* [PATCH v3 02/14] clk: sunxi-ng: Add common infrastructure
2016-06-29 19:05 [PATCH v3 00/14] clk: sunxi: introduce "modern" clock support Maxime Ripard
2016-06-29 19:05 ` [PATCH v3 01/14] dt-bindings: sunxi: Add CCU binding documentation Maxime Ripard
@ 2016-06-29 19:05 ` Maxime Ripard
2016-06-29 19:05 ` [PATCH v3 03/14] clk: sunxi-ng: Add fractional lib Maxime Ripard
` (11 subsequent siblings)
13 siblings, 0 replies; 22+ messages in thread
From: Maxime Ripard @ 2016-06-29 19:05 UTC (permalink / raw)
To: Mike Turquette, Stephen Boyd, Chen-Yu Tsai
Cc: linux-clk, Hans de Goede, Boris Brezillon, Rob Herring,
Vishnu Patekar, linux-arm-kernel, linux-kernel, devicetree,
Jean-Francois Moine, Maxime Ripard
Start our new clock infrastructure by adding the registration code, common
structure and common code.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
---
drivers/clk/Kconfig | 1 +
drivers/clk/Makefile | 1 +
drivers/clk/sunxi-ng/Kconfig | 3 ++
drivers/clk/sunxi-ng/Makefile | 3 ++
drivers/clk/sunxi-ng/ccu_common.c | 90 +++++++++++++++++++++++++++++++++++++++
drivers/clk/sunxi-ng/ccu_common.h | 85 ++++++++++++++++++++++++++++++++++++
drivers/clk/sunxi-ng/ccu_mult.h | 15 +++++++
drivers/clk/sunxi-ng/ccu_reset.c | 55 ++++++++++++++++++++++++
drivers/clk/sunxi-ng/ccu_reset.h | 40 +++++++++++++++++
9 files changed, 293 insertions(+)
create mode 100644 drivers/clk/sunxi-ng/Kconfig
create mode 100644 drivers/clk/sunxi-ng/Makefile
create mode 100644 drivers/clk/sunxi-ng/ccu_common.c
create mode 100644 drivers/clk/sunxi-ng/ccu_common.h
create mode 100644 drivers/clk/sunxi-ng/ccu_mult.h
create mode 100644 drivers/clk/sunxi-ng/ccu_reset.c
create mode 100644 drivers/clk/sunxi-ng/ccu_reset.h
diff --git a/drivers/clk/Kconfig b/drivers/clk/Kconfig
index 53ddba26578c..8216f47ac37d 100644
--- a/drivers/clk/Kconfig
+++ b/drivers/clk/Kconfig
@@ -212,6 +212,7 @@ source "drivers/clk/mvebu/Kconfig"
source "drivers/clk/qcom/Kconfig"
source "drivers/clk/renesas/Kconfig"
source "drivers/clk/samsung/Kconfig"
+source "drivers/clk/sunxi-ng/Kconfig"
source "drivers/clk/tegra/Kconfig"
source "drivers/clk/ti/Kconfig"
diff --git a/drivers/clk/Makefile b/drivers/clk/Makefile
index dcc5e698ff6d..7a44a1526d60 100644
--- a/drivers/clk/Makefile
+++ b/drivers/clk/Makefile
@@ -79,6 +79,7 @@ obj-$(CONFIG_ARCH_SOCFPGA) += socfpga/
obj-$(CONFIG_PLAT_SPEAR) += spear/
obj-$(CONFIG_ARCH_STI) += st/
obj-$(CONFIG_ARCH_SUNXI) += sunxi/
+obj-$(CONFIG_ARCH_SUNXI) += sunxi-ng/
obj-$(CONFIG_ARCH_TEGRA) += tegra/
obj-y += ti/
obj-$(CONFIG_ARCH_U8500) += ux500/
diff --git a/drivers/clk/sunxi-ng/Kconfig b/drivers/clk/sunxi-ng/Kconfig
new file mode 100644
index 000000000000..df5b2768d8b4
--- /dev/null
+++ b/drivers/clk/sunxi-ng/Kconfig
@@ -0,0 +1,3 @@
+config SUNXI_CCU
+ bool "Clock support for Allwinner SoCs"
+ default ARCH_SUNXI
diff --git a/drivers/clk/sunxi-ng/Makefile b/drivers/clk/sunxi-ng/Makefile
new file mode 100644
index 000000000000..886d0786ca51
--- /dev/null
+++ b/drivers/clk/sunxi-ng/Makefile
@@ -0,0 +1,3 @@
+# Common objects
+obj-$(CONFIG_SUNXI_CCU) += ccu_common.o
+obj-$(CONFIG_SUNXI_CCU) += ccu_reset.o
diff --git a/drivers/clk/sunxi-ng/ccu_common.c b/drivers/clk/sunxi-ng/ccu_common.c
new file mode 100644
index 000000000000..fc17b5295e16
--- /dev/null
+++ b/drivers/clk/sunxi-ng/ccu_common.c
@@ -0,0 +1,90 @@
+/*
+ * Copyright 2016 Maxime Ripard
+ *
+ * Maxime Ripard <maxime.ripard@free-electrons.com>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ */
+
+#include <linux/clk-provider.h>
+#include <linux/iopoll.h>
+#include <linux/slab.h>
+
+#include "ccu_common.h"
+#include "ccu_reset.h"
+
+static DEFINE_SPINLOCK(ccu_lock);
+
+void ccu_helper_wait_for_lock(struct ccu_common *common, u32 lock)
+{
+ u32 reg;
+
+ if (!lock)
+ return;
+
+ WARN_ON(readl_relaxed_poll_timeout(common->base + common->reg, reg,
+ !(reg & lock), 100, 70000));
+}
+
+int sunxi_ccu_probe(struct device_node *node, void __iomem *reg,
+ const struct sunxi_ccu_desc *desc)
+{
+ struct ccu_reset *reset;
+ int i, ret;
+
+ for (i = 0; i < desc->num_ccu_clks; i++) {
+ struct ccu_common *cclk = desc->ccu_clks[i];
+
+ if (!cclk)
+ continue;
+
+ cclk->base = reg;
+ cclk->lock = &ccu_lock;
+ }
+
+ for (i = 0; i < desc->hw_clks->num ; i++) {
+ struct clk_hw *hw = desc->hw_clks->hws[i];
+
+ if (!hw)
+ continue;
+
+ ret = clk_hw_register(NULL, hw);
+ if (ret) {
+ pr_err("Couldn't register clock %s\n",
+ clk_hw_get_name(hw));
+ goto err_clk_unreg;
+ }
+ }
+
+ ret = of_clk_add_hw_provider(node, of_clk_hw_onecell_get,
+ desc->hw_clks);
+ if (ret)
+ goto err_clk_unreg;
+
+ reset = kzalloc(sizeof(*reset), GFP_KERNEL);
+ reset->rcdev.of_node = node;
+ reset->rcdev.ops = &ccu_reset_ops;
+ reset->rcdev.owner = THIS_MODULE;
+ reset->rcdev.nr_resets = desc->num_resets;
+ reset->base = reg;
+ reset->lock = &ccu_lock;
+ reset->reset_map = desc->resets;
+
+ ret = reset_controller_register(&reset->rcdev);
+ if (ret)
+ goto err_of_clk_unreg;
+
+ return 0;
+
+err_of_clk_unreg:
+err_clk_unreg:
+ return ret;
+}
diff --git a/drivers/clk/sunxi-ng/ccu_common.h b/drivers/clk/sunxi-ng/ccu_common.h
new file mode 100644
index 000000000000..b3d9abfbd721
--- /dev/null
+++ b/drivers/clk/sunxi-ng/ccu_common.h
@@ -0,0 +1,85 @@
+/*
+ * Copyright (c) 2016 Maxime Ripard. All rights reserved.
+ *
+ * This software is licensed under the terms of the GNU General Public
+ * License version 2, as published by the Free Software Foundation, and
+ * may be copied, distributed, and modified under those terms.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ */
+
+#ifndef _COMMON_H_
+#define _COMMON_H_
+
+#include <linux/compiler.h>
+#include <linux/clk-provider.h>
+
+#define CCU_FEATURE_FRACTIONAL BIT(0)
+#define CCU_FEATURE_VARIABLE_PREDIV BIT(1)
+#define CCU_FEATURE_FIXED_PREDIV BIT(2)
+#define CCU_FEATURE_FIXED_POSTDIV BIT(3)
+
+struct device_node;
+
+#define CLK_HW_INIT(_name, _parent, _ops, _flags) \
+ &(struct clk_init_data) { \
+ .flags = _flags, \
+ .name = _name, \
+ .parent_names = (const char *[]) { _parent }, \
+ .num_parents = 1, \
+ .ops = _ops, \
+ }
+
+#define CLK_HW_INIT_PARENTS(_name, _parents, _ops, _flags) \
+ &(struct clk_init_data) { \
+ .flags = _flags, \
+ .name = _name, \
+ .parent_names = _parents, \
+ .num_parents = ARRAY_SIZE(_parents), \
+ .ops = _ops, \
+ }
+
+#define CLK_FIXED_FACTOR(_struct, _name, _parent, \
+ _div, _mult, _flags) \
+ struct clk_fixed_factor _struct = { \
+ .div = _div, \
+ .mult = _mult, \
+ .hw.init = CLK_HW_INIT(_name, \
+ _parent, \
+ &clk_fixed_factor_ops, \
+ _flags), \
+ }
+
+struct ccu_common {
+ void __iomem *base;
+ u16 reg;
+
+ unsigned long features;
+ spinlock_t *lock;
+ struct clk_hw hw;
+};
+
+static inline struct ccu_common *hw_to_ccu_common(struct clk_hw *hw)
+{
+ return container_of(hw, struct ccu_common, hw);
+}
+
+struct sunxi_ccu_desc {
+ struct ccu_common **ccu_clks;
+ unsigned long num_ccu_clks;
+
+ struct clk_hw_onecell_data *hw_clks;
+
+ struct ccu_reset_map *resets;
+ unsigned long num_resets;
+};
+
+void ccu_helper_wait_for_lock(struct ccu_common *common, u32 lock);
+
+int sunxi_ccu_probe(struct device_node *node, void __iomem *reg,
+ const struct sunxi_ccu_desc *desc);
+
+#endif /* _COMMON_H_ */
diff --git a/drivers/clk/sunxi-ng/ccu_mult.h b/drivers/clk/sunxi-ng/ccu_mult.h
new file mode 100644
index 000000000000..609db6610880
--- /dev/null
+++ b/drivers/clk/sunxi-ng/ccu_mult.h
@@ -0,0 +1,15 @@
+#ifndef _CCU_MULT_H_
+#define _CCU_MULT_H_
+
+struct _ccu_mult {
+ u8 shift;
+ u8 width;
+};
+
+#define _SUNXI_CCU_MULT(_shift, _width) \
+ { \
+ .shift = _shift, \
+ .width = _width, \
+ }
+
+#endif /* _CCU_MULT_H_ */
diff --git a/drivers/clk/sunxi-ng/ccu_reset.c b/drivers/clk/sunxi-ng/ccu_reset.c
new file mode 100644
index 000000000000..6c31d48783a7
--- /dev/null
+++ b/drivers/clk/sunxi-ng/ccu_reset.c
@@ -0,0 +1,55 @@
+/*
+ * Copyright (C) 2016 Maxime Ripard
+ * Maxime Ripard <maxime.ripard@free-electrons.com>
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ */
+
+#include <linux/io.h>
+#include <linux/reset-controller.h>
+
+#include "ccu_reset.h"
+
+static int ccu_reset_assert(struct reset_controller_dev *rcdev,
+ unsigned long id)
+{
+ struct ccu_reset *ccu = rcdev_to_ccu_reset(rcdev);
+ const struct ccu_reset_map *map = &ccu->reset_map[id];
+ unsigned long flags;
+ u32 reg;
+
+ spin_lock_irqsave(ccu->lock, flags);
+
+ reg = readl(ccu->base + map->reg);
+ writel(reg & ~map->bit, ccu->base + map->reg);
+
+ spin_unlock_irqrestore(ccu->lock, flags);
+
+ return 0;
+}
+
+static int ccu_reset_deassert(struct reset_controller_dev *rcdev,
+ unsigned long id)
+{
+ struct ccu_reset *ccu = rcdev_to_ccu_reset(rcdev);
+ const struct ccu_reset_map *map = &ccu->reset_map[id];
+ unsigned long flags;
+ u32 reg;
+
+ spin_lock_irqsave(ccu->lock, flags);
+
+ reg = readl(ccu->base + map->reg);
+ writel(reg | map->bit, ccu->base + map->reg);
+
+ spin_unlock_irqrestore(ccu->lock, flags);
+
+ return 0;
+}
+
+const struct reset_control_ops ccu_reset_ops = {
+ .assert = ccu_reset_assert,
+ .deassert = ccu_reset_deassert,
+};
diff --git a/drivers/clk/sunxi-ng/ccu_reset.h b/drivers/clk/sunxi-ng/ccu_reset.h
new file mode 100644
index 000000000000..36a4679210bd
--- /dev/null
+++ b/drivers/clk/sunxi-ng/ccu_reset.h
@@ -0,0 +1,40 @@
+/*
+ * Copyright (c) 2016 Maxime Ripard. All rights reserved.
+ *
+ * This software is licensed under the terms of the GNU General Public
+ * License version 2, as published by the Free Software Foundation, and
+ * may be copied, distributed, and modified under those terms.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ */
+
+#ifndef _CCU_RESET_H_
+#define _CCU_RESET_H_
+
+#include <linux/reset-controller.h>
+
+struct ccu_reset_map {
+ u16 reg;
+ u32 bit;
+};
+
+
+struct ccu_reset {
+ void __iomem *base;
+ struct ccu_reset_map *reset_map;
+ spinlock_t *lock;
+
+ struct reset_controller_dev rcdev;
+};
+
+static inline struct ccu_reset *rcdev_to_ccu_reset(struct reset_controller_dev *rcdev)
+{
+ return container_of(rcdev, struct ccu_reset, rcdev);
+}
+
+extern const struct reset_control_ops ccu_reset_ops;
+
+#endif /* _CCU_RESET_H_ */
--
2.9.0
^ permalink raw reply related [flat|nested] 22+ messages in thread
* [PATCH v3 03/14] clk: sunxi-ng: Add fractional lib
2016-06-29 19:05 [PATCH v3 00/14] clk: sunxi: introduce "modern" clock support Maxime Ripard
2016-06-29 19:05 ` [PATCH v3 01/14] dt-bindings: sunxi: Add CCU binding documentation Maxime Ripard
2016-06-29 19:05 ` [PATCH v3 02/14] clk: sunxi-ng: Add common infrastructure Maxime Ripard
@ 2016-06-29 19:05 ` Maxime Ripard
2016-06-29 19:05 ` [PATCH v3 04/14] clk: sunxi-ng: Add gate clock support Maxime Ripard
` (10 subsequent siblings)
13 siblings, 0 replies; 22+ messages in thread
From: Maxime Ripard @ 2016-06-29 19:05 UTC (permalink / raw)
To: Mike Turquette, Stephen Boyd, Chen-Yu Tsai
Cc: linux-clk, Hans de Goede, Boris Brezillon, Rob Herring,
Vishnu Patekar, linux-arm-kernel, linux-kernel, devicetree,
Jean-Francois Moine, Maxime Ripard
Some clocks can be switched to a mode called fractional that have two fixed
output rate you can choose from.
Add a small library to deal with those clocks.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
---
drivers/clk/sunxi-ng/Kconfig | 9 ++++
drivers/clk/sunxi-ng/Makefile | 3 ++
drivers/clk/sunxi-ng/ccu_frac.c | 110 ++++++++++++++++++++++++++++++++++++++++
drivers/clk/sunxi-ng/ccu_frac.h | 53 +++++++++++++++++++
4 files changed, 175 insertions(+)
create mode 100644 drivers/clk/sunxi-ng/ccu_frac.c
create mode 100644 drivers/clk/sunxi-ng/ccu_frac.h
diff --git a/drivers/clk/sunxi-ng/Kconfig b/drivers/clk/sunxi-ng/Kconfig
index df5b2768d8b4..3d117d7a3621 100644
--- a/drivers/clk/sunxi-ng/Kconfig
+++ b/drivers/clk/sunxi-ng/Kconfig
@@ -1,3 +1,12 @@
config SUNXI_CCU
bool "Clock support for Allwinner SoCs"
default ARCH_SUNXI
+
+if SUNXI_CCU
+
+# Base clock types
+
+config SUNXI_CCU_FRAC
+ bool
+
+endif
diff --git a/drivers/clk/sunxi-ng/Makefile b/drivers/clk/sunxi-ng/Makefile
index 886d0786ca51..46f417cb682a 100644
--- a/drivers/clk/sunxi-ng/Makefile
+++ b/drivers/clk/sunxi-ng/Makefile
@@ -1,3 +1,6 @@
# Common objects
obj-$(CONFIG_SUNXI_CCU) += ccu_common.o
obj-$(CONFIG_SUNXI_CCU) += ccu_reset.o
+
+# Base clock types
+obj-$(CONFIG_SUNXI_CCU_FRAC) += ccu_frac.o
diff --git a/drivers/clk/sunxi-ng/ccu_frac.c b/drivers/clk/sunxi-ng/ccu_frac.c
new file mode 100644
index 000000000000..5c4b10cd15b5
--- /dev/null
+++ b/drivers/clk/sunxi-ng/ccu_frac.c
@@ -0,0 +1,110 @@
+/*
+ * Copyright (C) 2016 Maxime Ripard
+ * Maxime Ripard <maxime.ripard@free-electrons.com>
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ */
+
+#include <linux/clk-provider.h>
+#include <linux/spinlock.h>
+
+#include "ccu_frac.h"
+
+bool ccu_frac_helper_is_enabled(struct ccu_common *common,
+ struct _ccu_frac *cf)
+{
+ if (!(common->features & CCU_FEATURE_FRACTIONAL))
+ return false;
+
+ return !(readl(common->base + common->reg) & cf->enable);
+}
+
+void ccu_frac_helper_enable(struct ccu_common *common,
+ struct _ccu_frac *cf)
+{
+ unsigned long flags;
+ u32 reg;
+
+ if (!(common->features & CCU_FEATURE_FRACTIONAL))
+ return;
+
+ spin_lock_irqsave(common->lock, flags);
+ reg = readl(common->base + common->reg);
+ writel(reg & ~cf->enable, common->base + common->reg);
+ spin_unlock_irqrestore(common->lock, flags);
+}
+
+void ccu_frac_helper_disable(struct ccu_common *common,
+ struct _ccu_frac *cf)
+{
+ unsigned long flags;
+ u32 reg;
+
+ if (!(common->features & CCU_FEATURE_FRACTIONAL))
+ return;
+
+ spin_lock_irqsave(common->lock, flags);
+ reg = readl(common->base + common->reg);
+ writel(reg | cf->enable, common->base + common->reg);
+ spin_unlock_irqrestore(common->lock, flags);
+}
+
+bool ccu_frac_helper_has_rate(struct ccu_common *common,
+ struct _ccu_frac *cf,
+ unsigned long rate)
+{
+ if (!(common->features & CCU_FEATURE_FRACTIONAL))
+ return false;
+
+ return (cf->rates[0] == rate) || (cf->rates[1] == rate);
+}
+
+unsigned long ccu_frac_helper_read_rate(struct ccu_common *common,
+ struct _ccu_frac *cf)
+{
+ u32 reg;
+
+ printk("%s: Read fractional\n", clk_hw_get_name(&common->hw));
+
+ if (!(common->features & CCU_FEATURE_FRACTIONAL))
+ return 0;
+
+ printk("%s: clock is fractional (rates %lu and %lu)\n",
+ clk_hw_get_name(&common->hw), cf->rates[0], cf->rates[1]);
+
+ reg = readl(common->base + common->reg);
+
+ printk("%s: clock reg is 0x%x (select is 0x%x)\n",
+ clk_hw_get_name(&common->hw), reg, cf->select);
+
+ return (reg & cf->select) ? cf->rates[1] : cf->rates[0];
+}
+
+int ccu_frac_helper_set_rate(struct ccu_common *common,
+ struct _ccu_frac *cf,
+ unsigned long rate)
+{
+ unsigned long flags;
+ u32 reg, sel;
+
+ if (!(common->features & CCU_FEATURE_FRACTIONAL))
+ return -EINVAL;
+
+ if (cf->rates[0] == rate)
+ sel = 0;
+ else if (cf->rates[1] == rate)
+ sel = cf->select;
+ else
+ return -EINVAL;
+
+ spin_lock_irqsave(common->lock, flags);
+ reg = readl(common->base + common->reg);
+ reg &= ~cf->select;
+ writel(reg | sel, common->base + common->reg);
+ spin_unlock_irqrestore(common->lock, flags);
+
+ return 0;
+}
diff --git a/drivers/clk/sunxi-ng/ccu_frac.h b/drivers/clk/sunxi-ng/ccu_frac.h
new file mode 100644
index 000000000000..e4c670b1cdfe
--- /dev/null
+++ b/drivers/clk/sunxi-ng/ccu_frac.h
@@ -0,0 +1,53 @@
+/*
+ * Copyright (c) 2016 Maxime Ripard. All rights reserved.
+ *
+ * This software is licensed under the terms of the GNU General Public
+ * License version 2, as published by the Free Software Foundation, and
+ * may be copied, distributed, and modified under those terms.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ */
+
+#ifndef _CCU_FRAC_H_
+#define _CCU_FRAC_H_
+
+#include <linux/clk-provider.h>
+
+#include "ccu_common.h"
+
+struct _ccu_frac {
+ u32 enable;
+ u32 select;
+
+ unsigned long rates[2];
+};
+
+#define _SUNXI_CCU_FRAC(_enable, _select, _rate1, _rate2) \
+ { \
+ .enable = _enable, \
+ .select = _select, \
+ .rates = { _rate1, _rate2 }, \
+ }
+
+bool ccu_frac_helper_is_enabled(struct ccu_common *common,
+ struct _ccu_frac *cf);
+void ccu_frac_helper_enable(struct ccu_common *common,
+ struct _ccu_frac *cf);
+void ccu_frac_helper_disable(struct ccu_common *common,
+ struct _ccu_frac *cf);
+
+bool ccu_frac_helper_has_rate(struct ccu_common *common,
+ struct _ccu_frac *cf,
+ unsigned long rate);
+
+unsigned long ccu_frac_helper_read_rate(struct ccu_common *common,
+ struct _ccu_frac *cf);
+
+int ccu_frac_helper_set_rate(struct ccu_common *common,
+ struct _ccu_frac *cf,
+ unsigned long rate);
+
+#endif /* _CCU_FRAC_H_ */
--
2.9.0
^ permalink raw reply related [flat|nested] 22+ messages in thread
* [PATCH v3 04/14] clk: sunxi-ng: Add gate clock support
2016-06-29 19:05 [PATCH v3 00/14] clk: sunxi: introduce "modern" clock support Maxime Ripard
` (2 preceding siblings ...)
2016-06-29 19:05 ` [PATCH v3 03/14] clk: sunxi-ng: Add fractional lib Maxime Ripard
@ 2016-06-29 19:05 ` Maxime Ripard
2016-06-29 19:05 ` [PATCH v3 05/14] clk: sunxi-ng: Add mux " Maxime Ripard
` (9 subsequent siblings)
13 siblings, 0 replies; 22+ messages in thread
From: Maxime Ripard @ 2016-06-29 19:05 UTC (permalink / raw)
To: Mike Turquette, Stephen Boyd, Chen-Yu Tsai
Cc: linux-clk, Hans de Goede, Boris Brezillon, Rob Herring,
Vishnu Patekar, linux-arm-kernel, linux-kernel, devicetree,
Jean-Francois Moine, Maxime Ripard
Some clocks in the Allwinner SoCs clocks unit are just simple gates. Add
support for those clocks.
Since it's a feature that can also be found in more complex clocks, provide
a bunch of helpers that can be reused later on.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
---
drivers/clk/sunxi-ng/Kconfig | 3 ++
drivers/clk/sunxi-ng/Makefile | 1 +
drivers/clk/sunxi-ng/ccu_gate.c | 82 +++++++++++++++++++++++++++++++++++++++++
drivers/clk/sunxi-ng/ccu_gate.h | 52 ++++++++++++++++++++++++++
4 files changed, 138 insertions(+)
create mode 100644 drivers/clk/sunxi-ng/ccu_gate.c
create mode 100644 drivers/clk/sunxi-ng/ccu_gate.h
diff --git a/drivers/clk/sunxi-ng/Kconfig b/drivers/clk/sunxi-ng/Kconfig
index 3d117d7a3621..2f135c8a61b6 100644
--- a/drivers/clk/sunxi-ng/Kconfig
+++ b/drivers/clk/sunxi-ng/Kconfig
@@ -9,4 +9,7 @@ if SUNXI_CCU
config SUNXI_CCU_FRAC
bool
+config SUNXI_CCU_GATE
+ bool
+
endif
diff --git a/drivers/clk/sunxi-ng/Makefile b/drivers/clk/sunxi-ng/Makefile
index 46f417cb682a..48b885f2d8ff 100644
--- a/drivers/clk/sunxi-ng/Makefile
+++ b/drivers/clk/sunxi-ng/Makefile
@@ -4,3 +4,4 @@ obj-$(CONFIG_SUNXI_CCU) += ccu_reset.o
# Base clock types
obj-$(CONFIG_SUNXI_CCU_FRAC) += ccu_frac.o
+obj-$(CONFIG_SUNXI_CCU_GATE) += ccu_gate.o
diff --git a/drivers/clk/sunxi-ng/ccu_gate.c b/drivers/clk/sunxi-ng/ccu_gate.c
new file mode 100644
index 000000000000..8a81f9d4a89f
--- /dev/null
+++ b/drivers/clk/sunxi-ng/ccu_gate.c
@@ -0,0 +1,82 @@
+/*
+ * Copyright (C) 2016 Maxime Ripard
+ * Maxime Ripard <maxime.ripard@free-electrons.com>
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ */
+
+#include <linux/clk-provider.h>
+
+#include "ccu_gate.h"
+
+void ccu_gate_helper_disable(struct ccu_common *common, u32 gate)
+{
+ unsigned long flags;
+ u32 reg;
+
+ if (!gate)
+ return;
+
+ spin_lock_irqsave(common->lock, flags);
+
+ reg = readl(common->base + common->reg);
+ writel(reg & ~gate, common->base + common->reg);
+
+ spin_unlock_irqrestore(common->lock, flags);
+}
+
+static void ccu_gate_disable(struct clk_hw *hw)
+{
+ struct ccu_gate *cg = hw_to_ccu_gate(hw);
+
+ return ccu_gate_helper_disable(&cg->common, cg->enable);
+}
+
+int ccu_gate_helper_enable(struct ccu_common *common, u32 gate)
+{
+ unsigned long flags;
+ u32 reg;
+
+ if (!gate)
+ return 0;
+
+ spin_lock_irqsave(common->lock, flags);
+
+ reg = readl(common->base + common->reg);
+ writel(reg | gate, common->base + common->reg);
+
+ spin_unlock_irqrestore(common->lock, flags);
+
+ return 0;
+}
+
+static int ccu_gate_enable(struct clk_hw *hw)
+{
+ struct ccu_gate *cg = hw_to_ccu_gate(hw);
+
+ return ccu_gate_helper_enable(&cg->common, cg->enable);
+}
+
+int ccu_gate_helper_is_enabled(struct ccu_common *common, u32 gate)
+{
+ if (!gate)
+ return 1;
+
+ return readl(common->base + common->reg) & gate;
+}
+
+static int ccu_gate_is_enabled(struct clk_hw *hw)
+{
+ struct ccu_gate *cg = hw_to_ccu_gate(hw);
+
+ return ccu_gate_helper_is_enabled(&cg->common, cg->enable);
+}
+
+const struct clk_ops ccu_gate_ops = {
+ .disable = ccu_gate_disable,
+ .enable = ccu_gate_enable,
+ .is_enabled = ccu_gate_is_enabled,
+};
diff --git a/drivers/clk/sunxi-ng/ccu_gate.h b/drivers/clk/sunxi-ng/ccu_gate.h
new file mode 100644
index 000000000000..4466169bd2d7
--- /dev/null
+++ b/drivers/clk/sunxi-ng/ccu_gate.h
@@ -0,0 +1,52 @@
+/*
+ * Copyright (c) 2016 Maxime Ripard. All rights reserved.
+ *
+ * This software is licensed under the terms of the GNU General Public
+ * License version 2, as published by the Free Software Foundation, and
+ * may be copied, distributed, and modified under those terms.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ */
+
+#ifndef _CCU_GATE_H_
+#define _CCU_GATE_H_
+
+#include <linux/clk-provider.h>
+
+#include "ccu_common.h"
+
+struct ccu_gate {
+ u32 enable;
+
+ struct ccu_common common;
+};
+
+#define SUNXI_CCU_GATE(_struct, _name, _parent, _reg, _gate, _flags) \
+ struct ccu_gate _struct = { \
+ .enable = _gate, \
+ .common = { \
+ .reg = _reg, \
+ .hw.init = CLK_HW_INIT(_name, \
+ _parent, \
+ &ccu_gate_ops, \
+ _flags), \
+ } \
+ }
+
+static inline struct ccu_gate *hw_to_ccu_gate(struct clk_hw *hw)
+{
+ struct ccu_common *common = hw_to_ccu_common(hw);
+
+ return container_of(common, struct ccu_gate, common);
+}
+
+void ccu_gate_helper_disable(struct ccu_common *common, u32 gate);
+int ccu_gate_helper_enable(struct ccu_common *common, u32 gate);
+int ccu_gate_helper_is_enabled(struct ccu_common *common, u32 gate);
+
+extern const struct clk_ops ccu_gate_ops;
+
+#endif /* _CCU_GATE_H_ */
--
2.9.0
^ permalink raw reply related [flat|nested] 22+ messages in thread
* [PATCH v3 05/14] clk: sunxi-ng: Add mux clock support
2016-06-29 19:05 [PATCH v3 00/14] clk: sunxi: introduce "modern" clock support Maxime Ripard
` (3 preceding siblings ...)
2016-06-29 19:05 ` [PATCH v3 04/14] clk: sunxi-ng: Add gate clock support Maxime Ripard
@ 2016-06-29 19:05 ` Maxime Ripard
2016-06-29 19:05 ` [PATCH v3 06/14] clk: sunxi-ng: Add phase " Maxime Ripard
` (8 subsequent siblings)
13 siblings, 0 replies; 22+ messages in thread
From: Maxime Ripard @ 2016-06-29 19:05 UTC (permalink / raw)
To: Mike Turquette, Stephen Boyd, Chen-Yu Tsai
Cc: linux-clk, Hans de Goede, Boris Brezillon, Rob Herring,
Vishnu Patekar, linux-arm-kernel, linux-kernel, devicetree,
Jean-Francois Moine, Maxime Ripard
Some clocks in the Allwinner SoCs clocks unit are just muxes.
However, those muxes might also be found in some other complicated clocks
that would benefit from the code in there to deal with "advanced" features,
like pre-dividers.
Introduce a set of helpers to reduce the code duplication in such cases.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
---
drivers/clk/sunxi-ng/Kconfig | 3 +
drivers/clk/sunxi-ng/Makefile | 1 +
drivers/clk/sunxi-ng/ccu_mux.c | 187 +++++++++++++++++++++++++++++++++++++++++
drivers/clk/sunxi-ng/ccu_mux.h | 91 ++++++++++++++++++++
4 files changed, 282 insertions(+)
create mode 100644 drivers/clk/sunxi-ng/ccu_mux.c
create mode 100644 drivers/clk/sunxi-ng/ccu_mux.h
diff --git a/drivers/clk/sunxi-ng/Kconfig b/drivers/clk/sunxi-ng/Kconfig
index 2f135c8a61b6..4699a602e0c1 100644
--- a/drivers/clk/sunxi-ng/Kconfig
+++ b/drivers/clk/sunxi-ng/Kconfig
@@ -12,4 +12,7 @@ config SUNXI_CCU_FRAC
config SUNXI_CCU_GATE
bool
+config SUNXI_CCU_MUX
+ bool
+
endif
diff --git a/drivers/clk/sunxi-ng/Makefile b/drivers/clk/sunxi-ng/Makefile
index 48b885f2d8ff..eaa833721245 100644
--- a/drivers/clk/sunxi-ng/Makefile
+++ b/drivers/clk/sunxi-ng/Makefile
@@ -5,3 +5,4 @@ obj-$(CONFIG_SUNXI_CCU) += ccu_reset.o
# Base clock types
obj-$(CONFIG_SUNXI_CCU_FRAC) += ccu_frac.o
obj-$(CONFIG_SUNXI_CCU_GATE) += ccu_gate.o
+obj-$(CONFIG_SUNXI_CCU_MUX) += ccu_mux.o
diff --git a/drivers/clk/sunxi-ng/ccu_mux.c b/drivers/clk/sunxi-ng/ccu_mux.c
new file mode 100644
index 000000000000..58fc36e7dcce
--- /dev/null
+++ b/drivers/clk/sunxi-ng/ccu_mux.c
@@ -0,0 +1,187 @@
+/*
+ * Copyright (C) 2016 Maxime Ripard
+ * Maxime Ripard <maxime.ripard@free-electrons.com>
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ */
+
+#include <linux/clk-provider.h>
+
+#include "ccu_gate.h"
+#include "ccu_mux.h"
+
+void ccu_mux_helper_adjust_parent_for_prediv(struct ccu_common *common,
+ struct ccu_mux_internal *cm,
+ int parent_index,
+ unsigned long *parent_rate)
+{
+ u8 prediv = 1;
+ u32 reg;
+
+ if (!((common->features & CCU_FEATURE_FIXED_PREDIV) ||
+ (common->features & CCU_FEATURE_VARIABLE_PREDIV)))
+ return;
+
+ reg = readl(common->base + common->reg);
+ if (parent_index < 0) {
+ parent_index = reg >> cm->shift;
+ parent_index &= (1 << cm->width) - 1;
+ }
+
+ if (common->features & CCU_FEATURE_FIXED_PREDIV)
+ if (parent_index == cm->fixed_prediv.index)
+ prediv = cm->fixed_prediv.div;
+
+ if (common->features & CCU_FEATURE_VARIABLE_PREDIV)
+ if (parent_index == cm->variable_prediv.index) {
+ u8 div;
+
+ div = reg >> cm->variable_prediv.shift;
+ div &= (1 << cm->variable_prediv.width) - 1;
+ prediv = div + 1;
+ }
+
+ *parent_rate = *parent_rate / prediv;
+}
+
+int ccu_mux_helper_determine_rate(struct ccu_common *common,
+ struct ccu_mux_internal *cm,
+ struct clk_rate_request *req,
+ unsigned long (*round)(struct ccu_mux_internal *,
+ unsigned long,
+ unsigned long,
+ void *),
+ void *data)
+{
+ unsigned long best_parent_rate = 0, best_rate = 0;
+ struct clk_hw *best_parent, *hw = &common->hw;
+ unsigned int i;
+
+ for (i = 0; i < clk_hw_get_num_parents(hw); i++) {
+ unsigned long tmp_rate, parent_rate;
+ struct clk_hw *parent;
+
+ parent = clk_hw_get_parent_by_index(hw, i);
+ if (!parent)
+ continue;
+
+ parent_rate = clk_hw_get_rate(parent);
+ ccu_mux_helper_adjust_parent_for_prediv(common, cm, i,
+ &parent_rate);
+
+ tmp_rate = round(cm, clk_hw_get_rate(parent), req->rate, data);
+ if (tmp_rate == req->rate) {
+ best_parent = parent;
+ best_parent_rate = parent_rate;
+ best_rate = tmp_rate;
+ goto out;
+ }
+
+ if ((req->rate - tmp_rate) < (req->rate - best_rate)) {
+ best_rate = tmp_rate;
+ best_parent_rate = parent_rate;
+ best_parent = parent;
+ }
+ }
+
+ if (best_rate == 0)
+ return -EINVAL;
+
+out:
+ req->best_parent_hw = best_parent;
+ req->best_parent_rate = best_parent_rate;
+ req->rate = best_rate;
+ return 0;
+}
+
+u8 ccu_mux_helper_get_parent(struct ccu_common *common,
+ struct ccu_mux_internal *cm)
+{
+ u32 reg;
+ u8 parent;
+
+ reg = readl(common->base + common->reg);
+ parent = reg >> cm->shift;
+ parent &= (1 << cm->width) - 1;
+
+ return parent;
+}
+
+int ccu_mux_helper_set_parent(struct ccu_common *common,
+ struct ccu_mux_internal *cm,
+ u8 index)
+{
+ unsigned long flags;
+ u32 reg;
+
+ spin_lock_irqsave(common->lock, flags);
+
+ reg = readl(common->base + common->reg);
+ reg &= ~GENMASK(cm->width + cm->shift - 1, cm->shift);
+ writel(reg | (index << cm->shift), common->base + common->reg);
+
+ spin_unlock_irqrestore(common->lock, flags);
+
+ return 0;
+}
+
+static void ccu_mux_disable(struct clk_hw *hw)
+{
+ struct ccu_mux *cm = hw_to_ccu_mux(hw);
+
+ return ccu_gate_helper_disable(&cm->common, cm->enable);
+}
+
+static int ccu_mux_enable(struct clk_hw *hw)
+{
+ struct ccu_mux *cm = hw_to_ccu_mux(hw);
+
+ return ccu_gate_helper_enable(&cm->common, cm->enable);
+}
+
+static int ccu_mux_is_enabled(struct clk_hw *hw)
+{
+ struct ccu_mux *cm = hw_to_ccu_mux(hw);
+
+ return ccu_gate_helper_is_enabled(&cm->common, cm->enable);
+}
+
+static u8 ccu_mux_get_parent(struct clk_hw *hw)
+{
+ struct ccu_mux *cm = hw_to_ccu_mux(hw);
+
+ return ccu_mux_helper_get_parent(&cm->common, &cm->mux);
+}
+
+static int ccu_mux_set_parent(struct clk_hw *hw, u8 index)
+{
+ struct ccu_mux *cm = hw_to_ccu_mux(hw);
+
+ return ccu_mux_helper_set_parent(&cm->common, &cm->mux, index);
+}
+
+static unsigned long ccu_mux_recalc_rate(struct clk_hw *hw,
+ unsigned long parent_rate)
+{
+ struct ccu_mux *cm = hw_to_ccu_mux(hw);
+
+ ccu_mux_helper_adjust_parent_for_prediv(&cm->common, &cm->mux, -1,
+ &parent_rate);
+
+ return parent_rate;
+}
+
+const struct clk_ops ccu_mux_ops = {
+ .disable = ccu_mux_disable,
+ .enable = ccu_mux_enable,
+ .is_enabled = ccu_mux_is_enabled,
+
+ .get_parent = ccu_mux_get_parent,
+ .set_parent = ccu_mux_set_parent,
+
+ .determine_rate = __clk_mux_determine_rate,
+ .recalc_rate = ccu_mux_recalc_rate,
+};
diff --git a/drivers/clk/sunxi-ng/ccu_mux.h b/drivers/clk/sunxi-ng/ccu_mux.h
new file mode 100644
index 000000000000..945082631e7d
--- /dev/null
+++ b/drivers/clk/sunxi-ng/ccu_mux.h
@@ -0,0 +1,91 @@
+#ifndef _CCU_MUX_H_
+#define _CCU_MUX_H_
+
+#include <linux/clk-provider.h>
+
+#include "ccu_common.h"
+
+struct ccu_mux_internal {
+ u8 shift;
+ u8 width;
+
+ struct {
+ u8 index;
+ u8 div;
+ } fixed_prediv;
+
+ struct {
+ u8 index;
+ u8 shift;
+ u8 width;
+ } variable_prediv;
+};
+
+#define SUNXI_CLK_MUX(_shift, _width) \
+ { \
+ .shift = _shift, \
+ .width = _width, \
+ }
+
+struct ccu_mux {
+ u16 reg;
+ u32 enable;
+
+ struct ccu_mux_internal mux;
+ struct ccu_common common;
+};
+
+#define SUNXI_CCU_MUX(_struct, _name, _parents, _reg, _shift, _width, _flags) \
+ struct ccu_mux _struct = { \
+ .mux = SUNXI_CLK_MUX(_shift, _width), \
+ .common = { \
+ .reg = _reg, \
+ .hw.init = CLK_HW_INIT_PARENTS(_name, \
+ _parents, \
+ &ccu_mux_ops, \
+ _flags), \
+ } \
+ }
+
+#define SUNXI_CCU_MUX_WITH_GATE(_struct, _name, _parents, _reg, \
+ _shift, _width, _gate, _flags) \
+ struct ccu_mux _struct = { \
+ .enable = _gate, \
+ .mux = SUNXI_CLK_MUX(_shift, _width), \
+ .common = { \
+ .reg = _reg, \
+ .hw.init = CLK_HW_INIT_PARENTS(_name, \
+ _parents, \
+ &ccu_mux_ops, \
+ _flags), \
+ } \
+ }
+
+static inline struct ccu_mux *hw_to_ccu_mux(struct clk_hw *hw)
+{
+ struct ccu_common *common = hw_to_ccu_common(hw);
+
+ return container_of(common, struct ccu_mux, common);
+}
+
+extern const struct clk_ops ccu_mux_ops;
+
+void ccu_mux_helper_adjust_parent_for_prediv(struct ccu_common *common,
+ struct ccu_mux_internal *cm,
+ int parent_index,
+ unsigned long *parent_rate);
+int ccu_mux_helper_determine_rate(struct ccu_common *common,
+ struct ccu_mux_internal *cm,
+ struct clk_rate_request *req,
+ unsigned long (*round)(struct ccu_mux_internal *,
+ unsigned long,
+ unsigned long,
+ void *),
+ void *data);
+u8 ccu_mux_helper_get_parent(struct ccu_common *common,
+ struct ccu_mux_internal *cm);
+int ccu_mux_helper_set_parent(struct ccu_common *common,
+ struct ccu_mux_internal *cm,
+ u8 index);
+
+#endif /* _CCU_MUX_H_ */
--
2.9.0
^ permalink raw reply related [flat|nested] 22+ messages in thread
* [PATCH v3 06/14] clk: sunxi-ng: Add phase clock support
2016-06-29 19:05 [PATCH v3 00/14] clk: sunxi: introduce "modern" clock support Maxime Ripard
` (4 preceding siblings ...)
2016-06-29 19:05 ` [PATCH v3 05/14] clk: sunxi-ng: Add mux " Maxime Ripard
@ 2016-06-29 19:05 ` Maxime Ripard
2016-06-29 19:05 ` [PATCH v3 07/14] clk: sunxi-ng: Add divider Maxime Ripard
` (7 subsequent siblings)
13 siblings, 0 replies; 22+ messages in thread
From: Maxime Ripard @ 2016-06-29 19:05 UTC (permalink / raw)
To: Mike Turquette, Stephen Boyd, Chen-Yu Tsai
Cc: linux-clk, Hans de Goede, Boris Brezillon, Rob Herring,
Vishnu Patekar, linux-arm-kernel, linux-kernel, devicetree,
Jean-Francois Moine, Maxime Ripard
Add support for the clocks in the CCU that introduce a phase shift from
their parent clock.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
---
drivers/clk/sunxi-ng/Kconfig | 3 +
drivers/clk/sunxi-ng/Makefile | 1 +
drivers/clk/sunxi-ng/ccu_phase.c | 126 +++++++++++++++++++++++++++++++++++++++
drivers/clk/sunxi-ng/ccu_phase.h | 50 ++++++++++++++++
4 files changed, 180 insertions(+)
create mode 100644 drivers/clk/sunxi-ng/ccu_phase.c
create mode 100644 drivers/clk/sunxi-ng/ccu_phase.h
diff --git a/drivers/clk/sunxi-ng/Kconfig b/drivers/clk/sunxi-ng/Kconfig
index 4699a602e0c1..3a3bc4368a2a 100644
--- a/drivers/clk/sunxi-ng/Kconfig
+++ b/drivers/clk/sunxi-ng/Kconfig
@@ -15,4 +15,7 @@ config SUNXI_CCU_GATE
config SUNXI_CCU_MUX
bool
+config SUNXI_CCU_PHASE
+ bool
+
endif
diff --git a/drivers/clk/sunxi-ng/Makefile b/drivers/clk/sunxi-ng/Makefile
index eaa833721245..a0c53c56ebfe 100644
--- a/drivers/clk/sunxi-ng/Makefile
+++ b/drivers/clk/sunxi-ng/Makefile
@@ -6,3 +6,4 @@ obj-$(CONFIG_SUNXI_CCU) += ccu_reset.o
obj-$(CONFIG_SUNXI_CCU_FRAC) += ccu_frac.o
obj-$(CONFIG_SUNXI_CCU_GATE) += ccu_gate.o
obj-$(CONFIG_SUNXI_CCU_MUX) += ccu_mux.o
+obj-$(CONFIG_SUNXI_CCU_PHASE) += ccu_phase.o
diff --git a/drivers/clk/sunxi-ng/ccu_phase.c b/drivers/clk/sunxi-ng/ccu_phase.c
new file mode 100644
index 000000000000..400c58ad72fd
--- /dev/null
+++ b/drivers/clk/sunxi-ng/ccu_phase.c
@@ -0,0 +1,126 @@
+/*
+ * Copyright (C) 2016 Maxime Ripard
+ * Maxime Ripard <maxime.ripard@free-electrons.com>
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ */
+
+#include <linux/clk-provider.h>
+#include <linux/spinlock.h>
+
+#include "ccu_phase.h"
+
+static int ccu_phase_get_phase(struct clk_hw *hw)
+{
+ struct ccu_phase *phase = hw_to_ccu_phase(hw);
+ struct clk_hw *parent, *grandparent;
+ unsigned int parent_rate, grandparent_rate;
+ u16 step, parent_div;
+ u32 reg;
+ u8 delay;
+
+ reg = readl(phase->common.base + phase->common.reg);
+ delay = (reg >> phase->shift);
+ delay &= (1 << phase->width) - 1;
+
+ if (!delay)
+ return 180;
+
+ /* Get our parent clock, it's the one that can adjust its rate */
+ parent = clk_hw_get_parent(hw);
+ if (!parent)
+ return -EINVAL;
+
+ /* And its rate */
+ parent_rate = clk_hw_get_rate(parent);
+ if (!parent_rate)
+ return -EINVAL;
+
+ /* Now, get our parent's parent (most likely some PLL) */
+ grandparent = clk_hw_get_parent(parent);
+ if (!grandparent)
+ return -EINVAL;
+
+ /* And its rate */
+ grandparent_rate = clk_hw_get_rate(grandparent);
+ if (!grandparent_rate)
+ return -EINVAL;
+
+ /* Get our parent clock divider */
+ parent_div = grandparent_rate / parent_rate;
+
+ step = DIV_ROUND_CLOSEST(360, parent_div);
+ return delay * step;
+}
+
+static int ccu_phase_set_phase(struct clk_hw *hw, int degrees)
+{
+ struct ccu_phase *phase = hw_to_ccu_phase(hw);
+ struct clk_hw *parent, *grandparent;
+ unsigned int parent_rate, grandparent_rate;
+ unsigned long flags;
+ u32 reg;
+ u8 delay;
+
+ /* Get our parent clock, it's the one that can adjust its rate */
+ parent = clk_hw_get_parent(hw);
+ if (!parent)
+ return -EINVAL;
+
+ /* And its rate */
+ parent_rate = clk_hw_get_rate(parent);
+ if (!parent_rate)
+ return -EINVAL;
+
+ /* Now, get our parent's parent (most likely some PLL) */
+ grandparent = clk_hw_get_parent(parent);
+ if (!grandparent)
+ return -EINVAL;
+
+ /* And its rate */
+ grandparent_rate = clk_hw_get_rate(grandparent);
+ if (!grandparent_rate)
+ return -EINVAL;
+
+ if (degrees != 180) {
+ u16 step, parent_div;
+
+ /* Get our parent divider */
+ parent_div = grandparent_rate / parent_rate;
+
+ /*
+ * We can only outphase the clocks by multiple of the
+ * PLL's period.
+ *
+ * Since our parent clock is only a divider, and the
+ * formula to get the outphasing in degrees is deg =
+ * 360 * delta / period
+ *
+ * If we simplify this formula, we can see that the
+ * only thing that we're concerned about is the number
+ * of period we want to outphase our clock from, and
+ * the divider set by our parent clock.
+ */
+ step = DIV_ROUND_CLOSEST(360, parent_div);
+ delay = DIV_ROUND_CLOSEST(degrees, step);
+ } else {
+ delay = 0;
+ }
+
+ spin_lock_irqsave(phase->common.lock, flags);
+ reg = readl(phase->common.base + phase->common.reg);
+ reg &= ~GENMASK(phase->width + phase->shift - 1, phase->shift);
+ writel(reg | (delay << phase->shift),
+ phase->common.base + phase->common.reg);
+ spin_unlock_irqrestore(phase->common.lock, flags);
+
+ return 0;
+}
+
+const struct clk_ops ccu_phase_ops = {
+ .get_phase = ccu_phase_get_phase,
+ .set_phase = ccu_phase_set_phase,
+};
diff --git a/drivers/clk/sunxi-ng/ccu_phase.h b/drivers/clk/sunxi-ng/ccu_phase.h
new file mode 100644
index 000000000000..75a091a4c565
--- /dev/null
+++ b/drivers/clk/sunxi-ng/ccu_phase.h
@@ -0,0 +1,50 @@
+/*
+ * Copyright (c) 2016 Maxime Ripard. All rights reserved.
+ *
+ * This software is licensed under the terms of the GNU General Public
+ * License version 2, as published by the Free Software Foundation, and
+ * may be copied, distributed, and modified under those terms.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ */
+
+#ifndef _CCU_PHASE_H_
+#define _CCU_PHASE_H_
+
+#include <linux/clk-provider.h>
+
+#include "ccu_common.h"
+
+struct ccu_phase {
+ u8 shift;
+ u8 width;
+
+ struct ccu_common common;
+};
+
+#define SUNXI_CCU_PHASE(_struct, _name, _parent, _reg, _shift, _width, _flags) \
+ struct ccu_phase _struct = { \
+ .shift = _shift, \
+ .width = _width, \
+ .common = { \
+ .reg = _reg, \
+ .hw.init = CLK_HW_INIT(_name, \
+ _parent, \
+ &ccu_phase_ops, \
+ _flags), \
+ } \
+ }
+
+static inline struct ccu_phase *hw_to_ccu_phase(struct clk_hw *hw)
+{
+ struct ccu_common *common = hw_to_ccu_common(hw);
+
+ return container_of(common, struct ccu_phase, common);
+}
+
+extern const struct clk_ops ccu_phase_ops;
+
+#endif /* _CCU_PHASE_H_ */
--
2.9.0
^ permalink raw reply related [flat|nested] 22+ messages in thread
* [PATCH v3 07/14] clk: sunxi-ng: Add divider
2016-06-29 19:05 [PATCH v3 00/14] clk: sunxi: introduce "modern" clock support Maxime Ripard
` (5 preceding siblings ...)
2016-06-29 19:05 ` [PATCH v3 06/14] clk: sunxi-ng: Add phase " Maxime Ripard
@ 2016-06-29 19:05 ` Maxime Ripard
2016-06-29 19:05 ` [PATCH v3 08/14] clk: sunxi-ng: Add M-P factor clock support Maxime Ripard
` (6 subsequent siblings)
13 siblings, 0 replies; 22+ messages in thread
From: Maxime Ripard @ 2016-06-29 19:05 UTC (permalink / raw)
To: Mike Turquette, Stephen Boyd, Chen-Yu Tsai
Cc: linux-clk, Hans de Goede, Boris Brezillon, Rob Herring,
Vishnu Patekar, linux-arm-kernel, linux-kernel, devicetree,
Jean-Francois Moine, Maxime Ripard
Add support for the various dividers (linear, table or pow-of-two based)
found in the CCU.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
---
drivers/clk/sunxi-ng/Kconfig | 4 ++
drivers/clk/sunxi-ng/Makefile | 1 +
drivers/clk/sunxi-ng/ccu_div.c | 136 +++++++++++++++++++++++++++++++++++++++++
drivers/clk/sunxi-ng/ccu_div.h | 133 ++++++++++++++++++++++++++++++++++++++++
4 files changed, 274 insertions(+)
create mode 100644 drivers/clk/sunxi-ng/ccu_div.c
create mode 100644 drivers/clk/sunxi-ng/ccu_div.h
diff --git a/drivers/clk/sunxi-ng/Kconfig b/drivers/clk/sunxi-ng/Kconfig
index 3a3bc4368a2a..7e65e776e7a8 100644
--- a/drivers/clk/sunxi-ng/Kconfig
+++ b/drivers/clk/sunxi-ng/Kconfig
@@ -6,6 +6,10 @@ if SUNXI_CCU
# Base clock types
+config SUNXI_CCU_DIV
+ bool
+ select SUNXI_CCU_MUX
+
config SUNXI_CCU_FRAC
bool
diff --git a/drivers/clk/sunxi-ng/Makefile b/drivers/clk/sunxi-ng/Makefile
index a0c53c56ebfe..4bc5b6168560 100644
--- a/drivers/clk/sunxi-ng/Makefile
+++ b/drivers/clk/sunxi-ng/Makefile
@@ -3,6 +3,7 @@ obj-$(CONFIG_SUNXI_CCU) += ccu_common.o
obj-$(CONFIG_SUNXI_CCU) += ccu_reset.o
# Base clock types
+obj-$(CONFIG_SUNXI_CCU_DIV) += ccu_div.o
obj-$(CONFIG_SUNXI_CCU_FRAC) += ccu_frac.o
obj-$(CONFIG_SUNXI_CCU_GATE) += ccu_gate.o
obj-$(CONFIG_SUNXI_CCU_MUX) += ccu_mux.o
diff --git a/drivers/clk/sunxi-ng/ccu_div.c b/drivers/clk/sunxi-ng/ccu_div.c
new file mode 100644
index 000000000000..8659b4cb6c20
--- /dev/null
+++ b/drivers/clk/sunxi-ng/ccu_div.c
@@ -0,0 +1,136 @@
+/*
+ * Copyright (C) 2016 Maxime Ripard
+ * Maxime Ripard <maxime.ripard@free-electrons.com>
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ */
+
+#include <linux/clk-provider.h>
+
+#include "ccu_gate.h"
+#include "ccu_div.h"
+
+static unsigned long ccu_div_round_rate(struct ccu_mux_internal *mux,
+ unsigned long parent_rate,
+ unsigned long rate,
+ void *data)
+{
+ struct ccu_div *cd = data;
+ unsigned long val;
+
+ /*
+ * We can't use divider_round_rate that assumes that there's
+ * several parents, while we might be called to evaluate
+ * several different parents.
+ */
+ val = divider_get_val(rate, parent_rate, cd->div.table, cd->div.width,
+ cd->div.flags);
+
+ return divider_recalc_rate(&cd->common.hw, parent_rate, val,
+ cd->div.table, cd->div.flags);
+}
+
+static void ccu_div_disable(struct clk_hw *hw)
+{
+ struct ccu_div *cd = hw_to_ccu_div(hw);
+
+ return ccu_gate_helper_disable(&cd->common, cd->enable);
+}
+
+static int ccu_div_enable(struct clk_hw *hw)
+{
+ struct ccu_div *cd = hw_to_ccu_div(hw);
+
+ return ccu_gate_helper_enable(&cd->common, cd->enable);
+}
+
+static int ccu_div_is_enabled(struct clk_hw *hw)
+{
+ struct ccu_div *cd = hw_to_ccu_div(hw);
+
+ return ccu_gate_helper_is_enabled(&cd->common, cd->enable);
+}
+
+static unsigned long ccu_div_recalc_rate(struct clk_hw *hw,
+ unsigned long parent_rate)
+{
+ struct ccu_div *cd = hw_to_ccu_div(hw);
+ unsigned long val;
+ u32 reg;
+
+ reg = readl(cd->common.base + cd->common.reg);
+ val = reg >> cd->div.shift;
+ val &= (1 << cd->div.width) - 1;
+
+ ccu_mux_helper_adjust_parent_for_prediv(&cd->common, &cd->mux, -1,
+ &parent_rate);
+
+ return divider_recalc_rate(hw, parent_rate, val, cd->div.table,
+ cd->div.flags);
+}
+
+static int ccu_div_determine_rate(struct clk_hw *hw,
+ struct clk_rate_request *req)
+{
+ struct ccu_div *cd = hw_to_ccu_div(hw);
+
+ return ccu_mux_helper_determine_rate(&cd->common, &cd->mux,
+ req, ccu_div_round_rate, cd);
+}
+
+static int ccu_div_set_rate(struct clk_hw *hw, unsigned long rate,
+ unsigned long parent_rate)
+{
+ struct ccu_div *cd = hw_to_ccu_div(hw);
+ unsigned long flags;
+ unsigned long val;
+ u32 reg;
+
+ ccu_mux_helper_adjust_parent_for_prediv(&cd->common, &cd->mux, -1,
+ &parent_rate);
+
+ val = divider_get_val(rate, parent_rate, cd->div.table, cd->div.width,
+ cd->div.flags);
+
+ spin_lock_irqsave(cd->common.lock, flags);
+
+ reg = readl(cd->common.base + cd->common.reg);
+ reg &= ~GENMASK(cd->div.width + cd->div.shift - 1, cd->div.shift);
+
+ writel(reg | (val << cd->div.shift),
+ cd->common.base + cd->common.reg);
+
+ spin_unlock_irqrestore(cd->common.lock, flags);
+
+ return 0;
+}
+
+static u8 ccu_div_get_parent(struct clk_hw *hw)
+{
+ struct ccu_div *cd = hw_to_ccu_div(hw);
+
+ return ccu_mux_helper_get_parent(&cd->common, &cd->mux);
+}
+
+static int ccu_div_set_parent(struct clk_hw *hw, u8 index)
+{
+ struct ccu_div *cd = hw_to_ccu_div(hw);
+
+ return ccu_mux_helper_set_parent(&cd->common, &cd->mux, index);
+}
+
+const struct clk_ops ccu_div_ops = {
+ .disable = ccu_div_disable,
+ .enable = ccu_div_enable,
+ .is_enabled = ccu_div_is_enabled,
+
+ .get_parent = ccu_div_get_parent,
+ .set_parent = ccu_div_set_parent,
+
+ .determine_rate = ccu_div_determine_rate,
+ .recalc_rate = ccu_div_recalc_rate,
+ .set_rate = ccu_div_set_rate,
+};
diff --git a/drivers/clk/sunxi-ng/ccu_div.h b/drivers/clk/sunxi-ng/ccu_div.h
new file mode 100644
index 000000000000..653ade5769b3
--- /dev/null
+++ b/drivers/clk/sunxi-ng/ccu_div.h
@@ -0,0 +1,133 @@
+/*
+ * Copyright (c) 2016 Maxime Ripard. All rights reserved.
+ *
+ * This software is licensed under the terms of the GNU General Public
+ * License version 2, as published by the Free Software Foundation, and
+ * may be copied, distributed, and modified under those terms.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ */
+
+#ifndef _CCU_DIV_H_
+#define _CCU_DIV_H_
+
+#include <linux/clk-provider.h>
+
+#include "ccu_common.h"
+#include "ccu_mux.h"
+
+struct _ccu_div {
+ u8 shift;
+ u8 width;
+
+ u32 flags;
+
+ struct clk_div_table *table;
+};
+
+#define _SUNXI_CCU_DIV_TABLE_FLAGS(_shift, _width, _table, _flags) \
+ { \
+ .shift = _shift, \
+ .width = _width, \
+ .flags = _flags, \
+ .table = _table, \
+ }
+
+#define _SUNXI_CCU_DIV_FLAGS(_shift, _width, _flags) \
+ _SUNXI_CCU_DIV_TABLE_FLAGS(_shift, _width, NULL, _flags)
+
+#define _SUNXI_CCU_DIV_TABLE(_shift, _width, _table) \
+ _SUNXI_CCU_DIV_TABLE_FLAGS(_shift, _width, _table, 0)
+
+#define _SUNXI_CCU_DIV(_shift, _width) \
+ _SUNXI_CCU_DIV_TABLE_FLAGS(_shift, _width, NULL, 0)
+
+struct ccu_div {
+ u32 enable;
+
+ struct _ccu_div div;
+ struct ccu_mux_internal mux;
+ struct ccu_common common;
+};
+
+#define SUNXI_CCU_DIV_TABLE_WITH_GATE(_struct, _name, _parent, _reg, \
+ _shift, _width, \
+ _table, _gate, _flags) \
+ struct ccu_div _struct = { \
+ .div = _SUNXI_CCU_DIV_TABLE(_shift, _width, \
+ _table), \
+ .enable = _gate, \
+ .common = { \
+ .reg = _reg, \
+ .hw.init = CLK_HW_INIT(_name, \
+ _parent, \
+ &ccu_div_ops, \
+ _flags), \
+ } \
+ }
+
+
+#define SUNXI_CCU_DIV_TABLE(_struct, _name, _parent, _reg, \
+ _shift, _width, \
+ _table, _flags) \
+ SUNXI_CCU_DIV_TABLE_WITH_GATE(_struct, _name, _parent, _reg, \
+ _shift, _width, _table, 0, \
+ _flags)
+
+#define SUNXI_CCU_M_WITH_MUX_GATE(_struct, _name, _parents, _reg, \
+ _mshift, _mwidth, _muxshift, _muxwidth, \
+ _gate, _flags) \
+ struct ccu_div _struct = { \
+ .enable = _gate, \
+ .div = _SUNXI_CCU_DIV(_mshift, _mwidth), \
+ .mux = SUNXI_CLK_MUX(_muxshift, _muxwidth), \
+ .common = { \
+ .reg = _reg, \
+ .hw.init = CLK_HW_INIT_PARENTS(_name, \
+ _parents, \
+ &ccu_div_ops, \
+ _flags), \
+ }, \
+ }
+
+#define SUNXI_CCU_M_WITH_MUX(_struct, _name, _parents, _reg, \
+ _mshift, _mwidth, _muxshift, _muxwidth, \
+ _flags) \
+ SUNXI_CCU_M_WITH_MUX_GATE(_struct, _name, _parents, _reg, \
+ _mshift, _mwidth, _muxshift, _muxwidth, \
+ 0, _flags)
+
+
+#define SUNXI_CCU_M_WITH_GATE(_struct, _name, _parent, _reg, \
+ _mshift, _mwidth, _gate, \
+ _flags) \
+ struct ccu_div _struct = { \
+ .enable = _gate, \
+ .div = _SUNXI_CCU_DIV(_mshift, _mwidth), \
+ .common = { \
+ .reg = _reg, \
+ .hw.init = CLK_HW_INIT(_name, \
+ _parent, \
+ &ccu_div_ops, \
+ _flags), \
+ }, \
+ }
+
+#define SUNXI_CCU_M(_struct, _name, _parent, _reg, _mshift, _mwidth, \
+ _flags) \
+ SUNXI_CCU_M_WITH_GATE(_struct, _name, _parent, _reg, \
+ _mshift, _mwidth, 0, _flags)
+
+static inline struct ccu_div *hw_to_ccu_div(struct clk_hw *hw)
+{
+ struct ccu_common *common = hw_to_ccu_common(hw);
+
+ return container_of(common, struct ccu_div, common);
+}
+
+extern const struct clk_ops ccu_div_ops;
+
+#endif /* _CCU_DIV_H_ */
--
2.9.0
^ permalink raw reply related [flat|nested] 22+ messages in thread
* [PATCH v3 08/14] clk: sunxi-ng: Add M-P factor clock support
2016-06-29 19:05 [PATCH v3 00/14] clk: sunxi: introduce "modern" clock support Maxime Ripard
` (6 preceding siblings ...)
2016-06-29 19:05 ` [PATCH v3 07/14] clk: sunxi-ng: Add divider Maxime Ripard
@ 2016-06-29 19:05 ` Maxime Ripard
2016-06-29 19:05 ` [PATCH v3 09/14] clk: sunxi-ng: Add N-K-factor " Maxime Ripard
` (5 subsequent siblings)
13 siblings, 0 replies; 22+ messages in thread
From: Maxime Ripard @ 2016-06-29 19:05 UTC (permalink / raw)
To: Mike Turquette, Stephen Boyd, Chen-Yu Tsai
Cc: linux-clk, Hans de Goede, Boris Brezillon, Rob Herring,
Vishnu Patekar, linux-arm-kernel, linux-kernel, devicetree,
Jean-Francois Moine, Maxime Ripard
Introduce support for the clocks that combine a linear divider and a
power-of-two based one.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
---
drivers/clk/sunxi-ng/Kconfig | 7 ++
drivers/clk/sunxi-ng/Makefile | 3 +
drivers/clk/sunxi-ng/ccu_mp.c | 158 ++++++++++++++++++++++++++++++++++++++++++
drivers/clk/sunxi-ng/ccu_mp.h | 77 ++++++++++++++++++++
4 files changed, 245 insertions(+)
create mode 100644 drivers/clk/sunxi-ng/ccu_mp.c
create mode 100644 drivers/clk/sunxi-ng/ccu_mp.h
diff --git a/drivers/clk/sunxi-ng/Kconfig b/drivers/clk/sunxi-ng/Kconfig
index 7e65e776e7a8..fc970b5a28c6 100644
--- a/drivers/clk/sunxi-ng/Kconfig
+++ b/drivers/clk/sunxi-ng/Kconfig
@@ -22,4 +22,11 @@ config SUNXI_CCU_MUX
config SUNXI_CCU_PHASE
bool
+# Multi-factor clocks
+
+config SUNXI_CCU_MP
+ bool
+ select SUNXI_CCU_GATE
+ select SUNXI_CCU_MUX
+
endif
diff --git a/drivers/clk/sunxi-ng/Makefile b/drivers/clk/sunxi-ng/Makefile
index 4bc5b6168560..501dec9451f4 100644
--- a/drivers/clk/sunxi-ng/Makefile
+++ b/drivers/clk/sunxi-ng/Makefile
@@ -8,3 +8,6 @@ obj-$(CONFIG_SUNXI_CCU_FRAC) += ccu_frac.o
obj-$(CONFIG_SUNXI_CCU_GATE) += ccu_gate.o
obj-$(CONFIG_SUNXI_CCU_MUX) += ccu_mux.o
obj-$(CONFIG_SUNXI_CCU_PHASE) += ccu_phase.o
+
+# Multi-factor clocks
+obj-$(CONFIG_SUNXI_CCU_MP) += ccu_mp.o
diff --git a/drivers/clk/sunxi-ng/ccu_mp.c b/drivers/clk/sunxi-ng/ccu_mp.c
new file mode 100644
index 000000000000..cbf33ef5faa9
--- /dev/null
+++ b/drivers/clk/sunxi-ng/ccu_mp.c
@@ -0,0 +1,158 @@
+/*
+ * Copyright (C) 2016 Maxime Ripard
+ * Maxime Ripard <maxime.ripard@free-electrons.com>
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ */
+
+#include <linux/clk-provider.h>
+
+#include "ccu_gate.h"
+#include "ccu_mp.h"
+
+static void ccu_mp_find_best(unsigned long parent, unsigned long rate,
+ unsigned int max_m, unsigned int max_p,
+ unsigned int *m, unsigned int *p)
+{
+ unsigned long best_rate = 0;
+ unsigned int best_m = 0, best_p = 0;
+ unsigned int _m, _p;
+
+ for (_p = 0; _p <= max_p; _p++) {
+ for (_m = 1; _m <= max_m; _m++) {
+ unsigned long tmp_rate = (parent >> _p) / _m;
+
+ if (tmp_rate > rate)
+ continue;
+
+ if ((rate - tmp_rate) < (rate - best_rate)) {
+ best_rate = tmp_rate;
+ best_m = _m;
+ best_p = _p;
+ }
+ }
+ }
+
+ *m = best_m;
+ *p = best_p;
+}
+
+static unsigned long ccu_mp_round_rate(struct ccu_mux_internal *mux,
+ unsigned long parent_rate,
+ unsigned long rate,
+ void *data)
+{
+ struct ccu_mp *cmp = data;
+ unsigned int m, p;
+
+ ccu_mp_find_best(parent_rate, rate,
+ 1 << cmp->m.width, (1 << cmp->p.width) - 1,
+ &m, &p);
+
+ return (parent_rate >> p) / m;
+}
+
+static void ccu_mp_disable(struct clk_hw *hw)
+{
+ struct ccu_mp *cmp = hw_to_ccu_mp(hw);
+
+ return ccu_gate_helper_disable(&cmp->common, cmp->enable);
+}
+
+static int ccu_mp_enable(struct clk_hw *hw)
+{
+ struct ccu_mp *cmp = hw_to_ccu_mp(hw);
+
+ return ccu_gate_helper_enable(&cmp->common, cmp->enable);
+}
+
+static int ccu_mp_is_enabled(struct clk_hw *hw)
+{
+ struct ccu_mp *cmp = hw_to_ccu_mp(hw);
+
+ return ccu_gate_helper_is_enabled(&cmp->common, cmp->enable);
+}
+
+static unsigned long ccu_mp_recalc_rate(struct clk_hw *hw,
+ unsigned long parent_rate)
+{
+ struct ccu_mp *cmp = hw_to_ccu_mp(hw);
+ unsigned int m, p;
+ u32 reg;
+
+ reg = readl(cmp->common.base + cmp->common.reg);
+
+ m = reg >> cmp->m.shift;
+ m &= (1 << cmp->m.width) - 1;
+
+ p = reg >> cmp->p.shift;
+ p &= (1 << cmp->p.width) - 1;
+
+ return (parent_rate >> p) / (m + 1);
+}
+
+static int ccu_mp_determine_rate(struct clk_hw *hw,
+ struct clk_rate_request *req)
+{
+ struct ccu_mp *cmp = hw_to_ccu_mp(hw);
+
+ return ccu_mux_helper_determine_rate(&cmp->common, &cmp->mux,
+ req, ccu_mp_round_rate, cmp);
+}
+
+static int ccu_mp_set_rate(struct clk_hw *hw, unsigned long rate,
+ unsigned long parent_rate)
+{
+ struct ccu_mp *cmp = hw_to_ccu_mp(hw);
+ unsigned long flags;
+ unsigned int m, p;
+ u32 reg;
+
+ ccu_mp_find_best(parent_rate, rate,
+ 1 << cmp->m.width, (1 << cmp->p.width) - 1,
+ &m, &p);
+
+
+ spin_lock_irqsave(cmp->common.lock, flags);
+
+ reg = readl(cmp->common.base + cmp->common.reg);
+ reg &= ~GENMASK(cmp->m.width + cmp->m.shift - 1, cmp->m.shift);
+ reg &= ~GENMASK(cmp->p.width + cmp->p.shift - 1, cmp->p.shift);
+
+ writel(reg | (p << cmp->p.shift) | ((m - 1) << cmp->m.shift),
+ cmp->common.base + cmp->common.reg);
+
+ spin_unlock_irqrestore(cmp->common.lock, flags);
+
+ return 0;
+}
+
+static u8 ccu_mp_get_parent(struct clk_hw *hw)
+{
+ struct ccu_mp *cmp = hw_to_ccu_mp(hw);
+
+ return ccu_mux_helper_get_parent(&cmp->common, &cmp->mux);
+}
+
+static int ccu_mp_set_parent(struct clk_hw *hw, u8 index)
+{
+ struct ccu_mp *cmp = hw_to_ccu_mp(hw);
+
+ return ccu_mux_helper_set_parent(&cmp->common, &cmp->mux, index);
+}
+
+const struct clk_ops ccu_mp_ops = {
+ .disable = ccu_mp_disable,
+ .enable = ccu_mp_enable,
+ .is_enabled = ccu_mp_is_enabled,
+
+ .get_parent = ccu_mp_get_parent,
+ .set_parent = ccu_mp_set_parent,
+
+ .determine_rate = ccu_mp_determine_rate,
+ .recalc_rate = ccu_mp_recalc_rate,
+ .set_rate = ccu_mp_set_rate,
+};
diff --git a/drivers/clk/sunxi-ng/ccu_mp.h b/drivers/clk/sunxi-ng/ccu_mp.h
new file mode 100644
index 000000000000..3cf12bf95962
--- /dev/null
+++ b/drivers/clk/sunxi-ng/ccu_mp.h
@@ -0,0 +1,77 @@
+/*
+ * Copyright (c) 2016 Maxime Ripard. All rights reserved.
+ *
+ * This software is licensed under the terms of the GNU General Public
+ * License version 2, as published by the Free Software Foundation, and
+ * may be copied, distributed, and modified under those terms.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ */
+
+#ifndef _CCU_MP_H_
+#define _CCU_MP_H_
+
+#include <linux/clk-provider.h>
+
+#include "ccu_common.h"
+#include "ccu_div.h"
+#include "ccu_mult.h"
+#include "ccu_mux.h"
+
+/*
+ * struct ccu_mp - Definition of an M-P clock
+ *
+ * Clocks based on the formula parent >> P / M
+ */
+struct ccu_mp {
+ u32 enable;
+
+ struct _ccu_div m;
+ struct _ccu_div p;
+ struct ccu_mux_internal mux;
+ struct ccu_common common;
+};
+
+#define SUNXI_CCU_MP_WITH_MUX_GATE(_struct, _name, _parents, _reg, \
+ _mshift, _mwidth, \
+ _pshift, _pwidth, \
+ _muxshift, _muxwidth, \
+ _gate, _flags) \
+ struct ccu_mp _struct = { \
+ .enable = _gate, \
+ .m = _SUNXI_CCU_DIV(_mshift, _mwidth), \
+ .p = _SUNXI_CCU_DIV(_pshift, _pwidth), \
+ .mux = SUNXI_CLK_MUX(_muxshift, _muxwidth), \
+ .common = { \
+ .reg = _reg, \
+ .hw.init = CLK_HW_INIT_PARENTS(_name, \
+ _parents, \
+ &ccu_mp_ops, \
+ _flags), \
+ } \
+ }
+
+#define SUNXI_CCU_MP_WITH_MUX(_struct, _name, _parents, _reg, \
+ _mshift, _mwidth, \
+ _pshift, _pwidth, \
+ _muxshift, _muxwidth, \
+ _flags) \
+ SUNXI_CCU_MP_WITH_MUX_GATE(_struct, _name, _parents, _reg, \
+ _mshift, _mwidth, \
+ _pshift, _pwidth, \
+ _muxshift, _muxwidth, \
+ 0, _flags)
+
+static inline struct ccu_mp *hw_to_ccu_mp(struct clk_hw *hw)
+{
+ struct ccu_common *common = hw_to_ccu_common(hw);
+
+ return container_of(common, struct ccu_mp, common);
+}
+
+extern const struct clk_ops ccu_mp_ops;
+
+#endif /* _CCU_MP_H_ */
--
2.9.0
^ permalink raw reply related [flat|nested] 22+ messages in thread
* [PATCH v3 09/14] clk: sunxi-ng: Add N-K-factor clock support
2016-06-29 19:05 [PATCH v3 00/14] clk: sunxi: introduce "modern" clock support Maxime Ripard
` (7 preceding siblings ...)
2016-06-29 19:05 ` [PATCH v3 08/14] clk: sunxi-ng: Add M-P factor clock support Maxime Ripard
@ 2016-06-29 19:05 ` Maxime Ripard
2016-06-29 19:05 ` [PATCH v3 10/14] clk: sunxi-ng: Add N-M-factor " Maxime Ripard
` (4 subsequent siblings)
13 siblings, 0 replies; 22+ messages in thread
From: Maxime Ripard @ 2016-06-29 19:05 UTC (permalink / raw)
To: Mike Turquette, Stephen Boyd, Chen-Yu Tsai
Cc: linux-clk, Hans de Goede, Boris Brezillon, Rob Herring,
Vishnu Patekar, linux-arm-kernel, linux-kernel, devicetree,
Jean-Francois Moine, Maxime Ripard
Introduce support for clocks that use a combination of two linear
multipliers.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
---
drivers/clk/sunxi-ng/Kconfig | 4 ++
drivers/clk/sunxi-ng/Makefile | 1 +
drivers/clk/sunxi-ng/ccu_nk.c | 147 ++++++++++++++++++++++++++++++++++++++++++
drivers/clk/sunxi-ng/ccu_nk.h | 71 ++++++++++++++++++++
4 files changed, 223 insertions(+)
create mode 100644 drivers/clk/sunxi-ng/ccu_nk.c
create mode 100644 drivers/clk/sunxi-ng/ccu_nk.h
diff --git a/drivers/clk/sunxi-ng/Kconfig b/drivers/clk/sunxi-ng/Kconfig
index fc970b5a28c6..2eb0fc6b41d5 100644
--- a/drivers/clk/sunxi-ng/Kconfig
+++ b/drivers/clk/sunxi-ng/Kconfig
@@ -24,6 +24,10 @@ config SUNXI_CCU_PHASE
# Multi-factor clocks
+config SUNXI_CCU_NK
+ bool
+ select SUNXI_CCU_GATE
+
config SUNXI_CCU_MP
bool
select SUNXI_CCU_GATE
diff --git a/drivers/clk/sunxi-ng/Makefile b/drivers/clk/sunxi-ng/Makefile
index 501dec9451f4..22951e60f876 100644
--- a/drivers/clk/sunxi-ng/Makefile
+++ b/drivers/clk/sunxi-ng/Makefile
@@ -10,4 +10,5 @@ obj-$(CONFIG_SUNXI_CCU_MUX) += ccu_mux.o
obj-$(CONFIG_SUNXI_CCU_PHASE) += ccu_phase.o
# Multi-factor clocks
+obj-$(CONFIG_SUNXI_CCU_NK) += ccu_nk.o
obj-$(CONFIG_SUNXI_CCU_MP) += ccu_mp.o
diff --git a/drivers/clk/sunxi-ng/ccu_nk.c b/drivers/clk/sunxi-ng/ccu_nk.c
new file mode 100644
index 000000000000..4470ffc8cf0d
--- /dev/null
+++ b/drivers/clk/sunxi-ng/ccu_nk.c
@@ -0,0 +1,147 @@
+/*
+ * Copyright (C) 2016 Maxime Ripard
+ * Maxime Ripard <maxime.ripard@free-electrons.com>
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ */
+
+#include <linux/clk-provider.h>
+#include <linux/rational.h>
+
+#include "ccu_gate.h"
+#include "ccu_nk.h"
+
+void ccu_nk_find_best(unsigned long parent, unsigned long rate,
+ unsigned int max_n, unsigned int max_k,
+ unsigned int *n, unsigned int *k)
+{
+ unsigned long best_rate = 0;
+ unsigned int best_k = 0, best_n = 0;
+ unsigned int _k, _n;
+
+ for (_k = 1; _k <= max_k; _k++) {
+ for (_n = 1; _n <= max_n; _n++) {
+ unsigned long tmp_rate = parent * _n * _k;
+
+ if (tmp_rate > rate)
+ continue;
+
+ if ((rate - tmp_rate) < (rate - best_rate)) {
+ best_rate = tmp_rate;
+ best_k = _k;
+ best_n = _n;
+ }
+ }
+ }
+
+ *k = best_k;
+ *n = best_n;
+}
+
+static void ccu_nk_disable(struct clk_hw *hw)
+{
+ struct ccu_nk *nk = hw_to_ccu_nk(hw);
+
+ return ccu_gate_helper_disable(&nk->common, nk->enable);
+}
+
+static int ccu_nk_enable(struct clk_hw *hw)
+{
+ struct ccu_nk *nk = hw_to_ccu_nk(hw);
+
+ return ccu_gate_helper_enable(&nk->common, nk->enable);
+}
+
+static int ccu_nk_is_enabled(struct clk_hw *hw)
+{
+ struct ccu_nk *nk = hw_to_ccu_nk(hw);
+
+ return ccu_gate_helper_is_enabled(&nk->common, nk->enable);
+}
+
+static unsigned long ccu_nk_recalc_rate(struct clk_hw *hw,
+ unsigned long parent_rate)
+{
+ struct ccu_nk *nk = hw_to_ccu_nk(hw);
+ unsigned long rate, n, k;
+ u32 reg;
+
+ reg = readl(nk->common.base + nk->common.reg);
+
+ n = reg >> nk->n.shift;
+ n &= (1 << nk->n.width) - 1;
+
+ k = reg >> nk->k.shift;
+ k &= (1 << nk->k.width) - 1;
+
+ rate = parent_rate * (n + 1) * (k + 1);
+
+ if (nk->common.features & CCU_FEATURE_FIXED_POSTDIV)
+ rate /= nk->fixed_post_div;
+
+ return rate;
+}
+
+static long ccu_nk_round_rate(struct clk_hw *hw, unsigned long rate,
+ unsigned long *parent_rate)
+{
+ struct ccu_nk *nk = hw_to_ccu_nk(hw);
+ unsigned int n, k;
+
+ if (nk->common.features & CCU_FEATURE_FIXED_POSTDIV)
+ rate *= nk->fixed_post_div;
+
+ ccu_nk_find_best(*parent_rate, rate,
+ 1 << nk->n.width, 1 << nk->k.width,
+ &n, &k);
+
+ rate = *parent_rate * n * k;
+ if (nk->common.features & CCU_FEATURE_FIXED_POSTDIV)
+ rate = rate / nk->fixed_post_div;
+
+ return rate;
+}
+
+static int ccu_nk_set_rate(struct clk_hw *hw, unsigned long rate,
+ unsigned long parent_rate)
+{
+ struct ccu_nk *nk = hw_to_ccu_nk(hw);
+ unsigned long flags;
+ unsigned int n, k;
+ u32 reg;
+
+ if (nk->common.features & CCU_FEATURE_FIXED_POSTDIV)
+ rate = rate * nk->fixed_post_div;
+
+ ccu_nk_find_best(parent_rate, rate,
+ 1 << nk->n.width, 1 << nk->k.width,
+ &n, &k);
+
+ spin_lock_irqsave(nk->common.lock, flags);
+
+ reg = readl(nk->common.base + nk->common.reg);
+ reg &= ~GENMASK(nk->n.width + nk->n.shift - 1, nk->n.shift);
+ reg &= ~GENMASK(nk->k.width + nk->k.shift - 1, nk->k.shift);
+
+ writel(reg | ((k - 1) << nk->k.shift) | ((n - 1) << nk->n.shift),
+ nk->common.base + nk->common.reg);
+
+ spin_unlock_irqrestore(nk->common.lock, flags);
+
+ ccu_helper_wait_for_lock(&nk->common, nk->lock);
+
+ return 0;
+}
+
+const struct clk_ops ccu_nk_ops = {
+ .disable = ccu_nk_disable,
+ .enable = ccu_nk_enable,
+ .is_enabled = ccu_nk_is_enabled,
+
+ .recalc_rate = ccu_nk_recalc_rate,
+ .round_rate = ccu_nk_round_rate,
+ .set_rate = ccu_nk_set_rate,
+};
diff --git a/drivers/clk/sunxi-ng/ccu_nk.h b/drivers/clk/sunxi-ng/ccu_nk.h
new file mode 100644
index 000000000000..4b52da0c29fe
--- /dev/null
+++ b/drivers/clk/sunxi-ng/ccu_nk.h
@@ -0,0 +1,71 @@
+/*
+ * Copyright (c) 2016 Maxime Ripard. All rights reserved.
+ *
+ * This software is licensed under the terms of the GNU General Public
+ * License version 2, as published by the Free Software Foundation, and
+ * may be copied, distributed, and modified under those terms.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ */
+
+#ifndef _CCU_NK_H_
+#define _CCU_NK_H_
+
+#include <linux/clk-provider.h>
+
+#include "ccu_common.h"
+#include "ccu_div.h"
+#include "ccu_mult.h"
+
+/*
+ * struct ccu_nk - Definition of an N-K clock
+ *
+ * Clocks based on the formula parent * N * K
+ */
+struct ccu_nk {
+ u16 reg;
+ u32 enable;
+ u32 lock;
+
+ struct _ccu_mult n;
+ struct _ccu_mult k;
+
+ unsigned int fixed_post_div;
+
+ struct ccu_common common;
+};
+
+#define SUNXI_CCU_NK_WITH_GATE_LOCK_POSTDIV(_struct, _name, _parent, _reg, \
+ _nshift, _nwidth, \
+ _kshift, _kwidth, \
+ _gate, _lock, _postdiv, \
+ _flags) \
+ struct ccu_nk _struct = { \
+ .enable = _gate, \
+ .lock = _lock, \
+ .k = _SUNXI_CCU_MULT(_kshift, _kwidth), \
+ .n = _SUNXI_CCU_MULT(_nshift, _nwidth), \
+ .fixed_post_div = _postdiv, \
+ .common = { \
+ .reg = _reg, \
+ .features = CCU_FEATURE_FIXED_POSTDIV, \
+ .hw.init = CLK_HW_INIT(_name, \
+ _parent, \
+ &ccu_nk_ops, \
+ _flags), \
+ }, \
+ }
+
+static inline struct ccu_nk *hw_to_ccu_nk(struct clk_hw *hw)
+{
+ struct ccu_common *common = hw_to_ccu_common(hw);
+
+ return container_of(common, struct ccu_nk, common);
+}
+
+extern const struct clk_ops ccu_nk_ops;
+
+#endif /* _CCU_NK_H_ */
--
2.9.0
^ permalink raw reply related [flat|nested] 22+ messages in thread
* [PATCH v3 10/14] clk: sunxi-ng: Add N-M-factor clock support
2016-06-29 19:05 [PATCH v3 00/14] clk: sunxi: introduce "modern" clock support Maxime Ripard
` (8 preceding siblings ...)
2016-06-29 19:05 ` [PATCH v3 09/14] clk: sunxi-ng: Add N-K-factor " Maxime Ripard
@ 2016-06-29 19:05 ` Maxime Ripard
2016-06-29 19:05 ` [PATCH v3 11/14] clk: sunxi-ng: Add N-K-M Factor clock Maxime Ripard
` (3 subsequent siblings)
13 siblings, 0 replies; 22+ messages in thread
From: Maxime Ripard @ 2016-06-29 19:05 UTC (permalink / raw)
To: Mike Turquette, Stephen Boyd, Chen-Yu Tsai
Cc: linux-clk, Hans de Goede, Boris Brezillon, Rob Herring,
Vishnu Patekar, linux-arm-kernel, linux-kernel, devicetree,
Jean-Francois Moine, Maxime Ripard
Introduce support for clocks that multiply and divide using linear factors.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
---
drivers/clk/sunxi-ng/Kconfig | 6 +++
drivers/clk/sunxi-ng/Makefile | 1 +
drivers/clk/sunxi-ng/ccu_nm.c | 114 ++++++++++++++++++++++++++++++++++++++++++
drivers/clk/sunxi-ng/ccu_nm.h | 91 +++++++++++++++++++++++++++++++++
4 files changed, 212 insertions(+)
create mode 100644 drivers/clk/sunxi-ng/ccu_nm.c
create mode 100644 drivers/clk/sunxi-ng/ccu_nm.h
diff --git a/drivers/clk/sunxi-ng/Kconfig b/drivers/clk/sunxi-ng/Kconfig
index 2eb0fc6b41d5..d8a5da270778 100644
--- a/drivers/clk/sunxi-ng/Kconfig
+++ b/drivers/clk/sunxi-ng/Kconfig
@@ -28,6 +28,12 @@ config SUNXI_CCU_NK
bool
select SUNXI_CCU_GATE
+config SUNXI_CCU_NM
+ bool
+ select RATIONAL
+ select SUNXI_CCU_FRAC
+ select SUNXI_CCU_GATE
+
config SUNXI_CCU_MP
bool
select SUNXI_CCU_GATE
diff --git a/drivers/clk/sunxi-ng/Makefile b/drivers/clk/sunxi-ng/Makefile
index 22951e60f876..7d2cd2a47a39 100644
--- a/drivers/clk/sunxi-ng/Makefile
+++ b/drivers/clk/sunxi-ng/Makefile
@@ -11,4 +11,5 @@ obj-$(CONFIG_SUNXI_CCU_PHASE) += ccu_phase.o
# Multi-factor clocks
obj-$(CONFIG_SUNXI_CCU_NK) += ccu_nk.o
+obj-$(CONFIG_SUNXI_CCU_NM) += ccu_nm.o
obj-$(CONFIG_SUNXI_CCU_MP) += ccu_mp.o
diff --git a/drivers/clk/sunxi-ng/ccu_nm.c b/drivers/clk/sunxi-ng/ccu_nm.c
new file mode 100644
index 000000000000..e35ddd8eec8b
--- /dev/null
+++ b/drivers/clk/sunxi-ng/ccu_nm.c
@@ -0,0 +1,114 @@
+/*
+ * Copyright (C) 2016 Maxime Ripard
+ * Maxime Ripard <maxime.ripard@free-electrons.com>
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ */
+
+#include <linux/clk-provider.h>
+#include <linux/rational.h>
+
+#include "ccu_frac.h"
+#include "ccu_gate.h"
+#include "ccu_nm.h"
+
+static void ccu_nm_disable(struct clk_hw *hw)
+{
+ struct ccu_nm *nm = hw_to_ccu_nm(hw);
+
+ return ccu_gate_helper_disable(&nm->common, nm->enable);
+}
+
+static int ccu_nm_enable(struct clk_hw *hw)
+{
+ struct ccu_nm *nm = hw_to_ccu_nm(hw);
+
+ return ccu_gate_helper_enable(&nm->common, nm->enable);
+}
+
+static int ccu_nm_is_enabled(struct clk_hw *hw)
+{
+ struct ccu_nm *nm = hw_to_ccu_nm(hw);
+
+ return ccu_gate_helper_is_enabled(&nm->common, nm->enable);
+}
+
+static unsigned long ccu_nm_recalc_rate(struct clk_hw *hw,
+ unsigned long parent_rate)
+{
+ struct ccu_nm *nm = hw_to_ccu_nm(hw);
+ unsigned long n, m;
+ u32 reg;
+
+ if (ccu_frac_helper_is_enabled(&nm->common, &nm->frac))
+ return ccu_frac_helper_read_rate(&nm->common, &nm->frac);
+
+ reg = readl(nm->common.base + nm->common.reg);
+
+ n = reg >> nm->n.shift;
+ n &= (1 << nm->n.width) - 1;
+
+ m = reg >> nm->m.shift;
+ m &= (1 << nm->m.width) - 1;
+
+ return parent_rate * (n + 1) / (m + 1);
+}
+
+static long ccu_nm_round_rate(struct clk_hw *hw, unsigned long rate,
+ unsigned long *parent_rate)
+{
+ struct ccu_nm *nm = hw_to_ccu_nm(hw);
+ unsigned long n, m;
+
+ rational_best_approximation(rate, *parent_rate,
+ 1 << nm->n.width, 1 << nm->m.width,
+ &n, &m);
+
+ return *parent_rate * n / m;
+}
+
+static int ccu_nm_set_rate(struct clk_hw *hw, unsigned long rate,
+ unsigned long parent_rate)
+{
+ struct ccu_nm *nm = hw_to_ccu_nm(hw);
+ unsigned long flags;
+ unsigned long n, m;
+ u32 reg;
+
+ if (ccu_frac_helper_has_rate(&nm->common, &nm->frac, rate))
+ return ccu_frac_helper_set_rate(&nm->common, &nm->frac, rate);
+ else
+ ccu_frac_helper_disable(&nm->common, &nm->frac);
+
+ rational_best_approximation(rate, parent_rate,
+ 1 << nm->n.width, 1 << nm->m.width,
+ &n, &m);
+
+ spin_lock_irqsave(nm->common.lock, flags);
+
+ reg = readl(nm->common.base + nm->common.reg);
+ reg &= ~GENMASK(nm->n.width + nm->n.shift - 1, nm->n.shift);
+ reg &= ~GENMASK(nm->m.width + nm->m.shift - 1, nm->m.shift);
+
+ writel(reg | ((m - 1) << nm->m.shift) | ((n - 1) << nm->n.shift),
+ nm->common.base + nm->common.reg);
+
+ spin_unlock_irqrestore(nm->common.lock, flags);
+
+ ccu_helper_wait_for_lock(&nm->common, nm->lock);
+
+ return 0;
+}
+
+const struct clk_ops ccu_nm_ops = {
+ .disable = ccu_nm_disable,
+ .enable = ccu_nm_enable,
+ .is_enabled = ccu_nm_is_enabled,
+
+ .recalc_rate = ccu_nm_recalc_rate,
+ .round_rate = ccu_nm_round_rate,
+ .set_rate = ccu_nm_set_rate,
+};
diff --git a/drivers/clk/sunxi-ng/ccu_nm.h b/drivers/clk/sunxi-ng/ccu_nm.h
new file mode 100644
index 000000000000..0b7bcd33a2df
--- /dev/null
+++ b/drivers/clk/sunxi-ng/ccu_nm.h
@@ -0,0 +1,91 @@
+/*
+ * Copyright (c) 2016 Maxime Ripard. All rights reserved.
+ *
+ * This software is licensed under the terms of the GNU General Public
+ * License version 2, as published by the Free Software Foundation, and
+ * may be copied, distributed, and modified under those terms.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ */
+
+#ifndef _CCU_NM_H_
+#define _CCU_NM_H_
+
+#include <linux/clk-provider.h>
+
+#include "ccu_common.h"
+#include "ccu_div.h"
+#include "ccu_frac.h"
+#include "ccu_mult.h"
+
+/*
+ * struct ccu_nm - Definition of an N-M clock
+ *
+ * Clocks based on the formula parent * N / M
+ */
+struct ccu_nm {
+ u32 enable;
+ u32 lock;
+
+ struct _ccu_mult n;
+ struct _ccu_div m;
+ struct _ccu_frac frac;
+
+ struct ccu_common common;
+};
+
+#define SUNXI_CCU_NM_WITH_FRAC_GATE_LOCK(_struct, _name, _parent, _reg, \
+ _nshift, _nwidth, \
+ _mshift, _mwidth, \
+ _frac_en, _frac_sel, \
+ _frac_rate_0, _frac_rate_1, \
+ _gate, _lock, _flags) \
+ struct ccu_nm _struct = { \
+ .enable = _gate, \
+ .lock = _lock, \
+ .n = _SUNXI_CCU_MULT(_nshift, _nwidth), \
+ .m = _SUNXI_CCU_DIV(_mshift, _mwidth), \
+ .frac = _SUNXI_CCU_FRAC(_frac_en, _frac_sel, \
+ _frac_rate_0, \
+ _frac_rate_1), \
+ .common = { \
+ .reg = _reg, \
+ .features = CCU_FEATURE_FRACTIONAL, \
+ .hw.init = CLK_HW_INIT(_name, \
+ _parent, \
+ &ccu_nm_ops, \
+ _flags), \
+ }, \
+ }
+
+#define SUNXI_CCU_NM_WITH_GATE_LOCK(_struct, _name, _parent, _reg, \
+ _nshift, _nwidth, \
+ _mshift, _mwidth, \
+ _gate, _lock, _flags) \
+ struct ccu_nm _struct = { \
+ .enable = _gate, \
+ .lock = _lock, \
+ .n = _SUNXI_CCU_MULT(_nshift, _nwidth), \
+ .m = _SUNXI_CCU_DIV(_mshift, _mwidth), \
+ .common = { \
+ .reg = _reg, \
+ .hw.init = CLK_HW_INIT(_name, \
+ _parent, \
+ &ccu_nm_ops, \
+ _flags), \
+ }, \
+ }
+
+static inline struct ccu_nm *hw_to_ccu_nm(struct clk_hw *hw)
+{
+ struct ccu_common *common = hw_to_ccu_common(hw);
+
+ return container_of(common, struct ccu_nm, common);
+}
+
+extern const struct clk_ops ccu_nm_ops;
+
+#endif /* _CCU_NM_H_ */
--
2.9.0
^ permalink raw reply related [flat|nested] 22+ messages in thread
* [PATCH v3 11/14] clk: sunxi-ng: Add N-K-M Factor clock
2016-06-29 19:05 [PATCH v3 00/14] clk: sunxi: introduce "modern" clock support Maxime Ripard
` (9 preceding siblings ...)
2016-06-29 19:05 ` [PATCH v3 10/14] clk: sunxi-ng: Add N-M-factor " Maxime Ripard
@ 2016-06-29 19:05 ` Maxime Ripard
2016-06-29 19:05 ` [PATCH v3 12/14] clk: sunxi-ng: Add N-K-M-P factor clock Maxime Ripard
` (2 subsequent siblings)
13 siblings, 0 replies; 22+ messages in thread
From: Maxime Ripard @ 2016-06-29 19:05 UTC (permalink / raw)
To: Mike Turquette, Stephen Boyd, Chen-Yu Tsai
Cc: linux-clk, Hans de Goede, Boris Brezillon, Rob Herring,
Vishnu Patekar, linux-arm-kernel, linux-kernel, devicetree,
Jean-Francois Moine, Maxime Ripard
Introduce support for clocks that multiply and divide using two linear
multipliers and one linear divider.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
---
drivers/clk/sunxi-ng/Kconfig | 5 ++
drivers/clk/sunxi-ng/Makefile | 1 +
drivers/clk/sunxi-ng/ccu_nkm.c | 153 +++++++++++++++++++++++++++++++++++++++++
drivers/clk/sunxi-ng/ccu_nkm.h | 68 ++++++++++++++++++
4 files changed, 227 insertions(+)
create mode 100644 drivers/clk/sunxi-ng/ccu_nkm.c
create mode 100644 drivers/clk/sunxi-ng/ccu_nkm.h
diff --git a/drivers/clk/sunxi-ng/Kconfig b/drivers/clk/sunxi-ng/Kconfig
index d8a5da270778..4c571b86bfd1 100644
--- a/drivers/clk/sunxi-ng/Kconfig
+++ b/drivers/clk/sunxi-ng/Kconfig
@@ -28,6 +28,11 @@ config SUNXI_CCU_NK
bool
select SUNXI_CCU_GATE
+config SUNXI_CCU_NKM
+ bool
+ select RATIONAL
+ select SUNXI_CCU_GATE
+
config SUNXI_CCU_NM
bool
select RATIONAL
diff --git a/drivers/clk/sunxi-ng/Makefile b/drivers/clk/sunxi-ng/Makefile
index 7d2cd2a47a39..2d6fdca0d3cc 100644
--- a/drivers/clk/sunxi-ng/Makefile
+++ b/drivers/clk/sunxi-ng/Makefile
@@ -11,5 +11,6 @@ obj-$(CONFIG_SUNXI_CCU_PHASE) += ccu_phase.o
# Multi-factor clocks
obj-$(CONFIG_SUNXI_CCU_NK) += ccu_nk.o
+obj-$(CONFIG_SUNXI_CCU_NKM) += ccu_nkm.o
obj-$(CONFIG_SUNXI_CCU_NM) += ccu_nm.o
obj-$(CONFIG_SUNXI_CCU_MP) += ccu_mp.o
diff --git a/drivers/clk/sunxi-ng/ccu_nkm.c b/drivers/clk/sunxi-ng/ccu_nkm.c
new file mode 100644
index 000000000000..2071822b1e9c
--- /dev/null
+++ b/drivers/clk/sunxi-ng/ccu_nkm.c
@@ -0,0 +1,153 @@
+/*
+ * Copyright (C) 2016 Maxime Ripard
+ * Maxime Ripard <maxime.ripard@free-electrons.com>
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ */
+
+#include <linux/clk-provider.h>
+#include <linux/rational.h>
+
+#include "ccu_gate.h"
+#include "ccu_nkm.h"
+
+struct _ccu_nkm {
+ unsigned long n, max_n;
+ unsigned long k, max_k;
+ unsigned long m, max_m;
+};
+
+static void ccu_nkm_find_best(unsigned long parent, unsigned long rate,
+ struct _ccu_nkm *nkm)
+{
+ unsigned long best_rate = 0;
+ unsigned long best_n = 0, best_k = 0, best_m = 0;
+ unsigned long _n, _k, _m;
+
+ for (_k = 1; _k <= nkm->max_k; _k++) {
+ unsigned long tmp_rate;
+
+ rational_best_approximation(rate / _k, parent,
+ nkm->max_n, nkm->max_m, &_n, &_m);
+
+ tmp_rate = parent * _n * _k / _m;
+
+ if (tmp_rate > rate)
+ continue;
+
+ if ((rate - tmp_rate) < (rate - best_rate)) {
+ best_rate = tmp_rate;
+ best_n = _n;
+ best_k = _k;
+ best_m = _m;
+ }
+ }
+
+ nkm->n = best_n;
+ nkm->k = best_k;
+ nkm->m = best_m;
+}
+
+static void ccu_nkm_disable(struct clk_hw *hw)
+{
+ struct ccu_nkm *nkm = hw_to_ccu_nkm(hw);
+
+ return ccu_gate_helper_disable(&nkm->common, nkm->enable);
+}
+
+static int ccu_nkm_enable(struct clk_hw *hw)
+{
+ struct ccu_nkm *nkm = hw_to_ccu_nkm(hw);
+
+ return ccu_gate_helper_enable(&nkm->common, nkm->enable);
+}
+
+static int ccu_nkm_is_enabled(struct clk_hw *hw)
+{
+ struct ccu_nkm *nkm = hw_to_ccu_nkm(hw);
+
+ return ccu_gate_helper_is_enabled(&nkm->common, nkm->enable);
+}
+
+static unsigned long ccu_nkm_recalc_rate(struct clk_hw *hw,
+ unsigned long parent_rate)
+{
+ struct ccu_nkm *nkm = hw_to_ccu_nkm(hw);
+ unsigned long n, m, k;
+ u32 reg;
+
+ reg = readl(nkm->common.base + nkm->common.reg);
+
+ n = reg >> nkm->n.shift;
+ n &= (1 << nkm->n.width) - 1;
+
+ k = reg >> nkm->k.shift;
+ k &= (1 << nkm->k.width) - 1;
+
+ m = reg >> nkm->m.shift;
+ m &= (1 << nkm->m.width) - 1;
+
+ return parent_rate * (n + 1) * (k + 1) / (m + 1);
+}
+
+static long ccu_nkm_round_rate(struct clk_hw *hw, unsigned long rate,
+ unsigned long *parent_rate)
+{
+ struct ccu_nkm *nkm = hw_to_ccu_nkm(hw);
+ struct _ccu_nkm _nkm;
+
+ _nkm.max_n = 1 << nkm->n.width;
+ _nkm.max_k = 1 << nkm->k.width;
+ _nkm.max_m = 1 << nkm->m.width;
+
+ ccu_nkm_find_best(*parent_rate, rate, &_nkm);
+
+ return *parent_rate * _nkm.n * _nkm.k / _nkm.m;
+}
+
+static int ccu_nkm_set_rate(struct clk_hw *hw, unsigned long rate,
+ unsigned long parent_rate)
+{
+ struct ccu_nkm *nkm = hw_to_ccu_nkm(hw);
+ struct _ccu_nkm _nkm;
+ unsigned long flags;
+ u32 reg;
+
+ _nkm.max_n = 1 << nkm->n.width;
+ _nkm.max_k = 1 << nkm->k.width;
+ _nkm.max_m = 1 << nkm->m.width;
+
+ ccu_nkm_find_best(parent_rate, rate, &_nkm);
+
+ spin_lock_irqsave(nkm->common.lock, flags);
+
+ reg = readl(nkm->common.base + nkm->common.reg);
+ reg &= ~GENMASK(nkm->n.width + nkm->n.shift - 1, nkm->n.shift);
+ reg &= ~GENMASK(nkm->k.width + nkm->k.shift - 1, nkm->k.shift);
+ reg &= ~GENMASK(nkm->m.width + nkm->m.shift - 1, nkm->m.shift);
+
+ reg |= (_nkm.n - 1) << nkm->n.shift;
+ reg |= (_nkm.k - 1) << nkm->k.shift;
+ reg |= (_nkm.m - 1) << nkm->m.shift;
+
+ writel(reg, nkm->common.base + nkm->common.reg);
+
+ spin_unlock_irqrestore(nkm->common.lock, flags);
+
+ ccu_helper_wait_for_lock(&nkm->common, nkm->lock);
+
+ return 0;
+}
+
+const struct clk_ops ccu_nkm_ops = {
+ .disable = ccu_nkm_disable,
+ .enable = ccu_nkm_enable,
+ .is_enabled = ccu_nkm_is_enabled,
+
+ .recalc_rate = ccu_nkm_recalc_rate,
+ .round_rate = ccu_nkm_round_rate,
+ .set_rate = ccu_nkm_set_rate,
+};
diff --git a/drivers/clk/sunxi-ng/ccu_nkm.h b/drivers/clk/sunxi-ng/ccu_nkm.h
new file mode 100644
index 000000000000..1936ac1c6b37
--- /dev/null
+++ b/drivers/clk/sunxi-ng/ccu_nkm.h
@@ -0,0 +1,68 @@
+/*
+ * Copyright (c) 2016 Maxime Ripard. All rights reserved.
+ *
+ * This software is licensed under the terms of the GNU General Public
+ * License version 2, as published by the Free Software Foundation, and
+ * may be copied, distributed, and modified under those terms.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ */
+
+#ifndef _CCU_NKM_H_
+#define _CCU_NKM_H_
+
+#include <linux/clk-provider.h>
+
+#include "ccu_common.h"
+#include "ccu_div.h"
+#include "ccu_mult.h"
+
+/*
+ * struct ccu_nkm - Definition of an N-K-M clock
+ *
+ * Clocks based on the formula parent * N * K / M
+ */
+struct ccu_nkm {
+ u32 enable;
+ u32 lock;
+
+ struct _ccu_mult n;
+ struct _ccu_mult k;
+ struct _ccu_div m;
+
+ struct ccu_common common;
+};
+
+#define SUNXI_CCU_NKM_WITH_GATE_LOCK(_struct, _name, _parent, _reg, \
+ _nshift, _nwidth, \
+ _kshift, _kwidth, \
+ _mshift, _mwidth, \
+ _gate, _lock, _flags) \
+ struct ccu_nkm _struct = { \
+ .enable = _gate, \
+ .lock = _lock, \
+ .k = _SUNXI_CCU_MULT(_kshift, _kwidth), \
+ .n = _SUNXI_CCU_MULT(_nshift, _nwidth), \
+ .m = _SUNXI_CCU_DIV(_mshift, _mwidth), \
+ .common = { \
+ .reg = _reg, \
+ .hw.init = CLK_HW_INIT(_name, \
+ _parent, \
+ &ccu_nkm_ops, \
+ _flags), \
+ }, \
+ }
+
+static inline struct ccu_nkm *hw_to_ccu_nkm(struct clk_hw *hw)
+{
+ struct ccu_common *common = hw_to_ccu_common(hw);
+
+ return container_of(common, struct ccu_nkm, common);
+}
+
+extern const struct clk_ops ccu_nkm_ops;
+
+#endif /* _CCU_NKM_H_ */
--
2.9.0
^ permalink raw reply related [flat|nested] 22+ messages in thread
* [PATCH v3 12/14] clk: sunxi-ng: Add N-K-M-P factor clock
2016-06-29 19:05 [PATCH v3 00/14] clk: sunxi: introduce "modern" clock support Maxime Ripard
` (10 preceding siblings ...)
2016-06-29 19:05 ` [PATCH v3 11/14] clk: sunxi-ng: Add N-K-M Factor clock Maxime Ripard
@ 2016-06-29 19:05 ` Maxime Ripard
2016-06-29 19:05 ` [PATCH v3 13/14] clk: sunxi-ng: Add H3 clocks Maxime Ripard
2016-06-29 19:05 ` [PATCH v3 14/14] ARM: dt: sun8i: switch the H3 to the new CCU driver Maxime Ripard
13 siblings, 0 replies; 22+ messages in thread
From: Maxime Ripard @ 2016-06-29 19:05 UTC (permalink / raw)
To: Mike Turquette, Stephen Boyd, Chen-Yu Tsai
Cc: linux-clk, Hans de Goede, Boris Brezillon, Rob Herring,
Vishnu Patekar, linux-arm-kernel, linux-kernel, devicetree,
Jean-Francois Moine, Maxime Ripard
Introduce support for clocks that use a combination of two linear
multipliers (N and K factors), one linear divider (M) and one power of two
divider (P).
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
---
drivers/clk/sunxi-ng/Kconfig | 5 ++
drivers/clk/sunxi-ng/Makefile | 1 +
drivers/clk/sunxi-ng/ccu_nkmp.c | 167 ++++++++++++++++++++++++++++++++++++++++
drivers/clk/sunxi-ng/ccu_nkmp.h | 71 +++++++++++++++++
4 files changed, 244 insertions(+)
create mode 100644 drivers/clk/sunxi-ng/ccu_nkmp.c
create mode 100644 drivers/clk/sunxi-ng/ccu_nkmp.h
diff --git a/drivers/clk/sunxi-ng/Kconfig b/drivers/clk/sunxi-ng/Kconfig
index 4c571b86bfd1..24fc9e4cc546 100644
--- a/drivers/clk/sunxi-ng/Kconfig
+++ b/drivers/clk/sunxi-ng/Kconfig
@@ -33,6 +33,11 @@ config SUNXI_CCU_NKM
select RATIONAL
select SUNXI_CCU_GATE
+config SUNXI_CCU_NKMP
+ bool
+ select RATIONAL
+ select SUNXI_CCU_GATE
+
config SUNXI_CCU_NM
bool
select RATIONAL
diff --git a/drivers/clk/sunxi-ng/Makefile b/drivers/clk/sunxi-ng/Makefile
index 2d6fdca0d3cc..5c342cc698d2 100644
--- a/drivers/clk/sunxi-ng/Makefile
+++ b/drivers/clk/sunxi-ng/Makefile
@@ -12,5 +12,6 @@ obj-$(CONFIG_SUNXI_CCU_PHASE) += ccu_phase.o
# Multi-factor clocks
obj-$(CONFIG_SUNXI_CCU_NK) += ccu_nk.o
obj-$(CONFIG_SUNXI_CCU_NKM) += ccu_nkm.o
+obj-$(CONFIG_SUNXI_CCU_NKMP) += ccu_nkmp.o
obj-$(CONFIG_SUNXI_CCU_NM) += ccu_nm.o
obj-$(CONFIG_SUNXI_CCU_MP) += ccu_mp.o
diff --git a/drivers/clk/sunxi-ng/ccu_nkmp.c b/drivers/clk/sunxi-ng/ccu_nkmp.c
new file mode 100644
index 000000000000..9f2b98e19dc9
--- /dev/null
+++ b/drivers/clk/sunxi-ng/ccu_nkmp.c
@@ -0,0 +1,167 @@
+/*
+ * Copyright (C) 2016 Maxime Ripard
+ * Maxime Ripard <maxime.ripard@free-electrons.com>
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ */
+
+#include <linux/clk-provider.h>
+#include <linux/rational.h>
+
+#include "ccu_gate.h"
+#include "ccu_nkmp.h"
+
+struct _ccu_nkmp {
+ unsigned long n, max_n;
+ unsigned long k, max_k;
+ unsigned long m, max_m;
+ unsigned long p, max_p;
+};
+
+static void ccu_nkmp_find_best(unsigned long parent, unsigned long rate,
+ struct _ccu_nkmp *nkmp)
+{
+ unsigned long best_rate = 0;
+ unsigned long best_n = 0, best_k = 0, best_m = 0, best_p = 0;
+ unsigned long _n, _k, _m, _p;
+
+ for (_k = 1; _k <= nkmp->max_k; _k++) {
+ for (_p = 0; _p <= nkmp->max_p; _p++) {
+ unsigned long tmp_rate;
+
+ rational_best_approximation(rate / _k, parent >> _p,
+ nkmp->max_n, nkmp->max_m,
+ &_n, &_m);
+
+ tmp_rate = (parent * _n * _k >> _p) / _m;
+
+ if (tmp_rate > rate)
+ continue;
+
+ if ((rate - tmp_rate) < (rate - best_rate)) {
+ best_rate = tmp_rate;
+ best_n = _n;
+ best_k = _k;
+ best_m = _m;
+ best_p = _p;
+ }
+ }
+ }
+
+ nkmp->n = best_n;
+ nkmp->k = best_k;
+ nkmp->m = best_m;
+ nkmp->p = best_p;
+}
+
+static void ccu_nkmp_disable(struct clk_hw *hw)
+{
+ struct ccu_nkmp *nkmp = hw_to_ccu_nkmp(hw);
+
+ return ccu_gate_helper_disable(&nkmp->common, nkmp->enable);
+}
+
+static int ccu_nkmp_enable(struct clk_hw *hw)
+{
+ struct ccu_nkmp *nkmp = hw_to_ccu_nkmp(hw);
+
+ return ccu_gate_helper_enable(&nkmp->common, nkmp->enable);
+}
+
+static int ccu_nkmp_is_enabled(struct clk_hw *hw)
+{
+ struct ccu_nkmp *nkmp = hw_to_ccu_nkmp(hw);
+
+ return ccu_gate_helper_is_enabled(&nkmp->common, nkmp->enable);
+}
+
+static unsigned long ccu_nkmp_recalc_rate(struct clk_hw *hw,
+ unsigned long parent_rate)
+{
+ struct ccu_nkmp *nkmp = hw_to_ccu_nkmp(hw);
+ unsigned long n, m, k, p;
+ u32 reg;
+
+ reg = readl(nkmp->common.base + nkmp->common.reg);
+
+ n = reg >> nkmp->n.shift;
+ n &= (1 << nkmp->n.width) - 1;
+
+ k = reg >> nkmp->k.shift;
+ k &= (1 << nkmp->k.width) - 1;
+
+ m = reg >> nkmp->m.shift;
+ m &= (1 << nkmp->m.width) - 1;
+
+ p = reg >> nkmp->p.shift;
+ p &= (1 << nkmp->p.width) - 1;
+
+ return (parent_rate * (n + 1) * (k + 1) >> p) / (m + 1);
+}
+
+static long ccu_nkmp_round_rate(struct clk_hw *hw, unsigned long rate,
+ unsigned long *parent_rate)
+{
+ struct ccu_nkmp *nkmp = hw_to_ccu_nkmp(hw);
+ struct _ccu_nkmp _nkmp;
+
+ _nkmp.max_n = 1 << nkmp->n.width;
+ _nkmp.max_k = 1 << nkmp->k.width;
+ _nkmp.max_m = 1 << nkmp->m.width;
+ _nkmp.max_p = (1 << nkmp->p.width) - 1;
+
+ ccu_nkmp_find_best(*parent_rate, rate,
+ &_nkmp);
+
+ return (*parent_rate * _nkmp.n * _nkmp.k >> _nkmp.p) / _nkmp.m;
+}
+
+static int ccu_nkmp_set_rate(struct clk_hw *hw, unsigned long rate,
+ unsigned long parent_rate)
+{
+ struct ccu_nkmp *nkmp = hw_to_ccu_nkmp(hw);
+ struct _ccu_nkmp _nkmp;
+ unsigned long flags;
+ u32 reg;
+
+ _nkmp.max_n = 1 << nkmp->n.width;
+ _nkmp.max_k = 1 << nkmp->k.width;
+ _nkmp.max_m = 1 << nkmp->m.width;
+ _nkmp.max_p = (1 << nkmp->p.width) - 1;
+
+ ccu_nkmp_find_best(parent_rate, rate, &_nkmp);
+
+ spin_lock_irqsave(nkmp->common.lock, flags);
+
+ reg = readl(nkmp->common.base + nkmp->common.reg);
+ reg &= ~GENMASK(nkmp->n.width + nkmp->n.shift - 1, nkmp->n.shift);
+ reg &= ~GENMASK(nkmp->k.width + nkmp->k.shift - 1, nkmp->k.shift);
+ reg &= ~GENMASK(nkmp->m.width + nkmp->m.shift - 1, nkmp->m.shift);
+ reg &= ~GENMASK(nkmp->p.width + nkmp->p.shift - 1, nkmp->p.shift);
+
+ reg |= (_nkmp.n - 1) << nkmp->n.shift;
+ reg |= (_nkmp.k - 1) << nkmp->k.shift;
+ reg |= (_nkmp.m - 1) << nkmp->m.shift;
+ reg |= _nkmp.p << nkmp->p.shift;
+
+ writel(reg, nkmp->common.base + nkmp->common.reg);
+
+ spin_unlock_irqrestore(nkmp->common.lock, flags);
+
+ ccu_helper_wait_for_lock(&nkmp->common, nkmp->lock);
+
+ return 0;
+}
+
+const struct clk_ops ccu_nkmp_ops = {
+ .disable = ccu_nkmp_disable,
+ .enable = ccu_nkmp_enable,
+ .is_enabled = ccu_nkmp_is_enabled,
+
+ .recalc_rate = ccu_nkmp_recalc_rate,
+ .round_rate = ccu_nkmp_round_rate,
+ .set_rate = ccu_nkmp_set_rate,
+};
diff --git a/drivers/clk/sunxi-ng/ccu_nkmp.h b/drivers/clk/sunxi-ng/ccu_nkmp.h
new file mode 100644
index 000000000000..5adb0c92a614
--- /dev/null
+++ b/drivers/clk/sunxi-ng/ccu_nkmp.h
@@ -0,0 +1,71 @@
+/*
+ * Copyright (c) 2016 Maxime Ripard. All rights reserved.
+ *
+ * This software is licensed under the terms of the GNU General Public
+ * License version 2, as published by the Free Software Foundation, and
+ * may be copied, distributed, and modified under those terms.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ */
+
+#ifndef _CCU_NKMP_H_
+#define _CCU_NKMP_H_
+
+#include <linux/clk-provider.h>
+
+#include "ccu_common.h"
+#include "ccu_div.h"
+#include "ccu_mult.h"
+
+/*
+ * struct ccu_nkmp - Definition of an N-K-M-P clock
+ *
+ * Clocks based on the formula parent * N * K >> P / M
+ */
+struct ccu_nkmp {
+ u32 enable;
+ u32 lock;
+
+ struct _ccu_mult n;
+ struct _ccu_mult k;
+ struct _ccu_div m;
+ struct _ccu_div p;
+
+ struct ccu_common common;
+};
+
+#define SUNXI_CCU_NKMP_WITH_GATE_LOCK(_struct, _name, _parent, _reg, \
+ _nshift, _nwidth, \
+ _kshift, _kwidth, \
+ _mshift, _mwidth, \
+ _pshift, _pwidth, \
+ _gate, _lock, _flags) \
+ struct ccu_nkmp _struct = { \
+ .enable = _gate, \
+ .lock = _lock, \
+ .n = _SUNXI_CCU_MULT(_nshift, _nwidth), \
+ .k = _SUNXI_CCU_MULT(_kshift, _kwidth), \
+ .m = _SUNXI_CCU_DIV(_mshift, _mwidth), \
+ .p = _SUNXI_CCU_DIV(_pshift, _pwidth), \
+ .common = { \
+ .reg = _reg, \
+ .hw.init = CLK_HW_INIT(_name, \
+ _parent, \
+ &ccu_nkmp_ops, \
+ _flags), \
+ }, \
+ }
+
+static inline struct ccu_nkmp *hw_to_ccu_nkmp(struct clk_hw *hw)
+{
+ struct ccu_common *common = hw_to_ccu_common(hw);
+
+ return container_of(common, struct ccu_nkmp, common);
+}
+
+extern const struct clk_ops ccu_nkmp_ops;
+
+#endif /* _CCU_NKMP_H_ */
--
2.9.0
^ permalink raw reply related [flat|nested] 22+ messages in thread
* [PATCH v3 13/14] clk: sunxi-ng: Add H3 clocks
2016-06-29 19:05 [PATCH v3 00/14] clk: sunxi: introduce "modern" clock support Maxime Ripard
` (11 preceding siblings ...)
2016-06-29 19:05 ` [PATCH v3 12/14] clk: sunxi-ng: Add N-K-M-P factor clock Maxime Ripard
@ 2016-06-29 19:05 ` Maxime Ripard
2016-06-30 8:31 ` Jean-Francois Moine
2016-07-07 2:33 ` Michael Turquette
2016-06-29 19:05 ` [PATCH v3 14/14] ARM: dt: sun8i: switch the H3 to the new CCU driver Maxime Ripard
13 siblings, 2 replies; 22+ messages in thread
From: Maxime Ripard @ 2016-06-29 19:05 UTC (permalink / raw)
To: Mike Turquette, Stephen Boyd, Chen-Yu Tsai
Cc: linux-clk, Hans de Goede, Boris Brezillon, Rob Herring,
Vishnu Patekar, linux-arm-kernel, linux-kernel, devicetree,
Jean-Francois Moine, Maxime Ripard
Add the list of clocks and resets found in the H3 CCU.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
---
drivers/clk/sunxi-ng/Kconfig | 13 +
drivers/clk/sunxi-ng/Makefile | 3 +
drivers/clk/sunxi-ng/ccu-sun8i-h3.c | 826 +++++++++++++++++++++++++++++++
drivers/clk/sunxi-ng/ccu-sun8i-h3.h | 62 +++
include/dt-bindings/clock/sun8i-h3-ccu.h | 145 ++++++
include/dt-bindings/reset/sun8i-h3-ccu.h | 103 ++++
6 files changed, 1152 insertions(+)
create mode 100644 drivers/clk/sunxi-ng/ccu-sun8i-h3.c
create mode 100644 drivers/clk/sunxi-ng/ccu-sun8i-h3.h
create mode 100644 include/dt-bindings/clock/sun8i-h3-ccu.h
create mode 100644 include/dt-bindings/reset/sun8i-h3-ccu.h
diff --git a/drivers/clk/sunxi-ng/Kconfig b/drivers/clk/sunxi-ng/Kconfig
index 24fc9e4cc546..41e53e8d4d41 100644
--- a/drivers/clk/sunxi-ng/Kconfig
+++ b/drivers/clk/sunxi-ng/Kconfig
@@ -49,4 +49,17 @@ config SUNXI_CCU_MP
select SUNXI_CCU_GATE
select SUNXI_CCU_MUX
+# SoC Drivers
+
+config SUN8I_H3_CCU
+ bool "Support for the Allwinner H3 CCU"
+ select SUNXI_CCU_DIV
+ select SUNXI_CCU_NK
+ select SUNXI_CCU_NKM
+ select SUNXI_CCU_NKMP
+ select SUNXI_CCU_NM
+ select SUNXI_CCU_MP
+ select SUNXI_CCU_PHASE
+ default ARCH_SUN8I
+
endif
diff --git a/drivers/clk/sunxi-ng/Makefile b/drivers/clk/sunxi-ng/Makefile
index 5c342cc698d2..633ce642ffae 100644
--- a/drivers/clk/sunxi-ng/Makefile
+++ b/drivers/clk/sunxi-ng/Makefile
@@ -15,3 +15,6 @@ obj-$(CONFIG_SUNXI_CCU_NKM) += ccu_nkm.o
obj-$(CONFIG_SUNXI_CCU_NKMP) += ccu_nkmp.o
obj-$(CONFIG_SUNXI_CCU_NM) += ccu_nm.o
obj-$(CONFIG_SUNXI_CCU_MP) += ccu_mp.o
+
+# SoC support
+obj-$(CONFIG_SUN8I_H3_CCU) += ccu-sun8i-h3.o
diff --git a/drivers/clk/sunxi-ng/ccu-sun8i-h3.c b/drivers/clk/sunxi-ng/ccu-sun8i-h3.c
new file mode 100644
index 000000000000..bcc0a95549d3
--- /dev/null
+++ b/drivers/clk/sunxi-ng/ccu-sun8i-h3.c
@@ -0,0 +1,826 @@
+/*
+ * Copyright (c) 2016 Maxime Ripard. All rights reserved.
+ *
+ * This software is licensed under the terms of the GNU General Public
+ * License version 2, as published by the Free Software Foundation, and
+ * may be copied, distributed, and modified under those terms.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ */
+
+#include <linux/clk-provider.h>
+#include <linux/of_address.h>
+
+#include "ccu_common.h"
+#include "ccu_reset.h"
+
+#include "ccu_div.h"
+#include "ccu_gate.h"
+#include "ccu_mp.h"
+#include "ccu_mult.h"
+#include "ccu_nk.h"
+#include "ccu_nkm.h"
+#include "ccu_nkmp.h"
+#include "ccu_nm.h"
+#include "ccu_phase.h"
+
+#include "ccu-sun8i-h3.h"
+
+static SUNXI_CCU_NKMP_WITH_GATE_LOCK(pll_cpux_clk, "pll-cpux",
+ "osc24M", 0x000,
+ 8, 5, /* N */
+ 4, 2, /* K */
+ 0, 2, /* M */
+ 16, 2, /* P */
+ BIT(31), /* gate */
+ BIT(28), /* lock */
+ 0);
+
+/*
+ * The Audio PLL is supposed to have 4 outputs: 3 fixed factors from
+ * the base (2x, 4x and 8x), and one variable divider (the one true
+ * pll audio).
+ *
+ * We don't have any need for the variable divider for now, so we just
+ * hardcode it to match with the clock names
+ */
+#define SUN8I_H3_PLL_AUDIO_REG 0x008
+
+static SUNXI_CCU_NM_WITH_GATE_LOCK(pll_audio_base_clk, "pll-audio-base",
+ "osc24M", 0x008,
+ 8, 7, /* N */
+ 0, 5, /* M */
+ BIT(31), /* gate */
+ BIT(28), /* lock */
+ 0);
+
+static SUNXI_CCU_NM_WITH_FRAC_GATE_LOCK(pll_video_clk, "pll-video",
+ "osc24M", 0x0010,
+ 8, 7, /* N */
+ 0, 4, /* M */
+ BIT(24), /* frac enable */
+ BIT(25), /* frac select */
+ 270000000, /* frac rate 0 */
+ 297000000, /* frac rate 1 */
+ BIT(31), /* gate */
+ BIT(28), /* lock */
+ 0);
+
+static SUNXI_CCU_NM_WITH_FRAC_GATE_LOCK(pll_ve_clk, "pll-ve",
+ "osc24M", 0x0018,
+ 8, 7, /* N */
+ 0, 4, /* M */
+ BIT(24), /* frac enable */
+ BIT(25), /* frac select */
+ 270000000, /* frac rate 0 */
+ 297000000, /* frac rate 1 */
+ BIT(31), /* gate */
+ BIT(28), /* lock */
+ 0);
+
+static SUNXI_CCU_NKM_WITH_GATE_LOCK(pll_ddr_clk, "pll-ddr",
+ "osc24M", 0x020,
+ 8, 5, /* N */
+ 4, 2, /* K */
+ 0, 2, /* M */
+ BIT(31), /* gate */
+ BIT(28), /* lock */
+ 0);
+
+static SUNXI_CCU_NK_WITH_GATE_LOCK_POSTDIV(pll_periph0_clk, "pll-periph0",
+ "osc24M", 0x028,
+ 8, 5, /* N */
+ 4, 2, /* K */
+ BIT(31), /* gate */
+ BIT(28), /* lock */
+ 2, /* post-div */
+ 0);
+
+static SUNXI_CCU_NM_WITH_FRAC_GATE_LOCK(pll_gpu_clk, "pll-gpu",
+ "osc24M", 0x0038,
+ 8, 7, /* N */
+ 0, 4, /* M */
+ BIT(24), /* frac enable */
+ BIT(25), /* frac select */
+ 270000000, /* frac rate 0 */
+ 297000000, /* frac rate 1 */
+ BIT(31), /* gate */
+ BIT(28), /* lock */
+ 0);
+
+static SUNXI_CCU_NK_WITH_GATE_LOCK_POSTDIV(pll_periph1_clk, "pll-periph1",
+ "osc24M", 0x044,
+ 8, 5, /* N */
+ 4, 2, /* K */
+ BIT(31), /* gate */
+ BIT(28), /* lock */
+ 2, /* post-div */
+ 0);
+
+static SUNXI_CCU_NM_WITH_FRAC_GATE_LOCK(pll_de_clk, "pll-de",
+ "osc24M", 0x0048,
+ 8, 7, /* N */
+ 0, 4, /* M */
+ BIT(24), /* frac enable */
+ BIT(25), /* frac select */
+ 270000000, /* frac rate 0 */
+ 297000000, /* frac rate 1 */
+ BIT(31), /* gate */
+ BIT(28), /* lock */
+ 0);
+
+static const char * const cpux_parents[] = { "osc32k", "osc24M",
+ "pll-cpux" , "pll-cpux" };
+static SUNXI_CCU_MUX(cpux_clk, "cpux", cpux_parents,
+ 0x050, 16, 2, CLK_IS_CRITICAL);
+
+static SUNXI_CCU_M(axi_clk, "axi", "cpux", 0x050, 0, 2, 0);
+
+static const char * const ahb1_parents[] = { "osc32k", "osc24M",
+ "axi" , "pll-periph0" };
+static struct ccu_div ahb1_clk = {
+ .div = _SUNXI_CCU_DIV_FLAGS(4, 2, CLK_DIVIDER_POWER_OF_TWO),
+
+ .mux = {
+ .shift = 12,
+ .width = 2,
+
+ .variable_prediv = {
+ .index = 3,
+ .shift = 6,
+ .width = 2,
+ },
+ },
+
+ .common = {
+ .reg = 0x054,
+ .features = CCU_FEATURE_VARIABLE_PREDIV,
+ .hw.init = CLK_HW_INIT_PARENTS("ahb1",
+ ahb1_parents,
+ &ccu_div_ops,
+ 0),
+ },
+};
+
+static struct clk_div_table apb1_div_table[] = {
+ { .val = 0, .div = 2 },
+ { .val = 1, .div = 2 },
+ { .val = 2, .div = 4 },
+ { .val = 3, .div = 8 },
+ { /* Sentinel */ },
+};
+static SUNXI_CCU_DIV_TABLE(apb1_clk, "apb1", "ahb1",
+ 0x054, 8, 2, apb1_div_table, 0);
+
+static const char * const apb2_parents[] = { "osc32k", "osc24M",
+ "pll-periph0" , "pll-periph0" };
+static SUNXI_CCU_MP_WITH_MUX(apb2_clk, "apb2", apb2_parents, 0x058,
+ 0, 5, /* M */
+ 16, 2, /* P */
+ 24, 2, /* mux */
+ 0);
+
+static const char * const ahb2_parents[] = { "ahb1" , "pll-periph0" };
+static struct ccu_mux ahb2_clk = {
+ .mux = {
+ .shift = 0,
+ .width = 1,
+
+ .fixed_prediv = {
+ .index = 1,
+ .div = 2,
+ },
+ },
+
+ .common = {
+ .reg = 0x05c,
+ .features = CCU_FEATURE_FIXED_PREDIV,
+ .hw.init = CLK_HW_INIT_PARENTS("ahb2",
+ ahb2_parents,
+ &ccu_mux_ops,
+ 0),
+ },
+};
+
+static SUNXI_CCU_GATE(bus_ce_clk, "bus-ce", "ahb1",
+ 0x060, BIT(5), 0);
+static SUNXI_CCU_GATE(bus_dma_clk, "bus-dma", "ahb1",
+ 0x060, BIT(6), 0);
+static SUNXI_CCU_GATE(bus_mmc0_clk, "bus-mmc0", "ahb1",
+ 0x060, BIT(8), 0);
+static SUNXI_CCU_GATE(bus_mmc1_clk, "bus-mmc1", "ahb1",
+ 0x060, BIT(9), 0);
+static SUNXI_CCU_GATE(bus_mmc2_clk, "bus-mmc2", "ahb1",
+ 0x060, BIT(10), 0);
+static SUNXI_CCU_GATE(bus_nand_clk, "bus-nand", "ahb1",
+ 0x060, BIT(13), 0);
+static SUNXI_CCU_GATE(bus_dram_clk, "bus-dram", "ahb1",
+ 0x060, BIT(14), 0);
+static SUNXI_CCU_GATE(bus_emac_clk, "bus-emac", "ahb2",
+ 0x060, BIT(17), 0);
+static SUNXI_CCU_GATE(bus_ts_clk, "bus-ts", "ahb1",
+ 0x060, BIT(18), 0);
+static SUNXI_CCU_GATE(bus_hstimer_clk, "bus-hstimer", "ahb1",
+ 0x060, BIT(19), 0);
+static SUNXI_CCU_GATE(bus_spi0_clk, "bus-spi0", "ahb1",
+ 0x060, BIT(20), 0);
+static SUNXI_CCU_GATE(bus_spi1_clk, "bus-spi1", "ahb1",
+ 0x060, BIT(21), 0);
+static SUNXI_CCU_GATE(bus_otg_clk, "bus-otg", "ahb1",
+ 0x060, BIT(23), 0);
+static SUNXI_CCU_GATE(bus_ehci0_clk, "bus-ehci0", "ahb1",
+ 0x060, BIT(24), 0);
+static SUNXI_CCU_GATE(bus_ehci1_clk, "bus-ehci1", "ahb2",
+ 0x060, BIT(25), 0);
+static SUNXI_CCU_GATE(bus_ehci2_clk, "bus-ehci2", "ahb2",
+ 0x060, BIT(26), 0);
+static SUNXI_CCU_GATE(bus_ehci3_clk, "bus-ehci3", "ahb2",
+ 0x060, BIT(27), 0);
+static SUNXI_CCU_GATE(bus_ohci0_clk, "bus-ohci0", "ahb1",
+ 0x060, BIT(28), 0);
+static SUNXI_CCU_GATE(bus_ohci1_clk, "bus-ohci1", "ahb2",
+ 0x060, BIT(29), 0);
+static SUNXI_CCU_GATE(bus_ohci2_clk, "bus-ohci2", "ahb2",
+ 0x060, BIT(30), 0);
+static SUNXI_CCU_GATE(bus_ohci3_clk, "bus-ohci3", "ahb2",
+ 0x060, BIT(31), 0);
+
+static SUNXI_CCU_GATE(bus_ve_clk, "bus-ve", "ahb1",
+ 0x064, BIT(0), 0);
+static SUNXI_CCU_GATE(bus_tcon0_clk, "bus-tcon0", "ahb1",
+ 0x064, BIT(3), 0);
+static SUNXI_CCU_GATE(bus_tcon1_clk, "bus-tcon1", "ahb1",
+ 0x064, BIT(4), 0);
+static SUNXI_CCU_GATE(bus_deinterlace_clk, "bus-deinterlace", "ahb1",
+ 0x064, BIT(5), 0);
+static SUNXI_CCU_GATE(bus_csi_clk, "bus-csi", "ahb1",
+ 0x064, BIT(8), 0);
+static SUNXI_CCU_GATE(bus_tve_clk, "bus-tve", "ahb1",
+ 0x064, BIT(9), 0);
+static SUNXI_CCU_GATE(bus_hdmi_clk, "bus-hdmi", "ahb1",
+ 0x064, BIT(11), 0);
+static SUNXI_CCU_GATE(bus_de_clk, "bus-de", "ahb1",
+ 0x064, BIT(12), 0);
+static SUNXI_CCU_GATE(bus_gpu_clk, "bus-gpu", "ahb1",
+ 0x064, BIT(20), 0);
+static SUNXI_CCU_GATE(bus_msgbox_clk, "bus-msgbox", "ahb1",
+ 0x064, BIT(21), 0);
+static SUNXI_CCU_GATE(bus_spinlock_clk, "bus-spinlock", "ahb1",
+ 0x064, BIT(22), 0);
+
+static SUNXI_CCU_GATE(bus_codec_clk, "bus-codec", "apb1",
+ 0x068, BIT(0), 0);
+static SUNXI_CCU_GATE(bus_spdif_clk, "bus-spdif", "apb1",
+ 0x068, BIT(1), 0);
+static SUNXI_CCU_GATE(bus_pio_clk, "bus-pio", "apb1",
+ 0x068, BIT(5), 0);
+static SUNXI_CCU_GATE(bus_ths_clk, "bus-ths", "apb1",
+ 0x068, BIT(8), 0);
+static SUNXI_CCU_GATE(bus_i2s0_clk, "bus-i2s0", "apb1",
+ 0x068, BIT(12), 0);
+static SUNXI_CCU_GATE(bus_i2s1_clk, "bus-i2s1", "apb1",
+ 0x068, BIT(13), 0);
+static SUNXI_CCU_GATE(bus_i2s2_clk, "bus-i2s2", "apb1",
+ 0x068, BIT(14), 0);
+
+static SUNXI_CCU_GATE(bus_i2c0_clk, "bus-i2c0", "apb2",
+ 0x06c, BIT(0), 0);
+static SUNXI_CCU_GATE(bus_i2c1_clk, "bus-i2c1", "apb2",
+ 0x06c, BIT(1), 0);
+static SUNXI_CCU_GATE(bus_i2c2_clk, "bus-i2c2", "apb2",
+ 0x06c, BIT(2), 0);
+static SUNXI_CCU_GATE(bus_uart0_clk, "bus-uart0", "apb2",
+ 0x06c, BIT(16), 0);
+static SUNXI_CCU_GATE(bus_uart1_clk, "bus-uart1", "apb2",
+ 0x06c, BIT(17), 0);
+static SUNXI_CCU_GATE(bus_uart2_clk, "bus-uart2", "apb2",
+ 0x06c, BIT(18), 0);
+static SUNXI_CCU_GATE(bus_uart3_clk, "bus-uart3", "apb2",
+ 0x06c, BIT(19), 0);
+static SUNXI_CCU_GATE(bus_scr_clk, "bus-scr", "apb2",
+ 0x06c, BIT(20), 0);
+
+static SUNXI_CCU_GATE(bus_ephy_clk, "bus-ephy", "ahb1",
+ 0x070, BIT(0), 0);
+static SUNXI_CCU_GATE(bus_dbg_clk, "bus-dbg", "ahb1",
+ 0x070, BIT(7), 0);
+
+static struct clk_div_table ths_div_table[] = {
+ { .val = 0, .div = 1 },
+ { .val = 1, .div = 2 },
+ { .val = 2, .div = 4 },
+ { .val = 3, .div = 6 },
+};
+static SUNXI_CCU_DIV_TABLE_WITH_GATE(ths_clk, "ths", "osc24M",
+ 0x074, 0, 2, ths_div_table, BIT(31), 0);
+
+static const char * const mod0_default_parents[] = { "osc24M", "pll-periph0",
+ "pll-periph1" };
+static SUNXI_CCU_MP_WITH_MUX_GATE(nand_clk, "nand", mod0_default_parents, 0x080,
+ 0, 4, /* M */
+ 16, 2, /* P */
+ 24, 2, /* mux */
+ BIT(31), /* gate */
+ 0);
+
+static SUNXI_CCU_MP_WITH_MUX_GATE(mmc0_clk, "mmc0", mod0_default_parents, 0x088,
+ 0, 4, /* M */
+ 16, 2, /* P */
+ 24, 2, /* mux */
+ BIT(31), /* gate */
+ 0);
+
+static SUNXI_CCU_PHASE(mmc0_sample_clk, "mmc0_sample", "mmc0",
+ 0x088, 20, 3, 0);
+static SUNXI_CCU_PHASE(mmc0_output_clk, "mmc0_output", "mmc0",
+ 0x088, 8, 3, 0);
+
+static SUNXI_CCU_MP_WITH_MUX_GATE(mmc1_clk, "mmc1", mod0_default_parents, 0x08c,
+ 0, 4, /* M */
+ 16, 2, /* P */
+ 24, 2, /* mux */
+ BIT(31), /* gate */
+ 0);
+
+static SUNXI_CCU_PHASE(mmc1_sample_clk, "mmc1_sample", "mmc1",
+ 0x08c, 20, 3, 0);
+static SUNXI_CCU_PHASE(mmc1_output_clk, "mmc1_output", "mmc1",
+ 0x08c, 8, 3, 0);
+
+static SUNXI_CCU_MP_WITH_MUX_GATE(mmc2_clk, "mmc2", mod0_default_parents, 0x090,
+ 0, 4, /* M */
+ 16, 2, /* P */
+ 24, 2, /* mux */
+ BIT(31), /* gate */
+ 0);
+
+static SUNXI_CCU_PHASE(mmc2_sample_clk, "mmc2_sample", "mmc2",
+ 0x090, 20, 3, 0);
+static SUNXI_CCU_PHASE(mmc2_output_clk, "mmc2_output", "mmc2",
+ 0x090, 8, 3, 0);
+
+static const char * const ts_parents[] = { "osc24M", "pll-periph0", };
+static SUNXI_CCU_MP_WITH_MUX_GATE(ts_clk, "ts", ts_parents, 0x098,
+ 0, 4, /* M */
+ 16, 2, /* P */
+ 24, 2, /* mux */
+ BIT(31), /* gate */
+ 0);
+
+static SUNXI_CCU_MP_WITH_MUX_GATE(ce_clk, "ce", mod0_default_parents, 0x09c,
+ 0, 4, /* M */
+ 16, 2, /* P */
+ 24, 2, /* mux */
+ BIT(31), /* gate */
+ 0);
+
+static SUNXI_CCU_MP_WITH_MUX_GATE(spi0_clk, "spi0", mod0_default_parents, 0x0a0,
+ 0, 4, /* M */
+ 16, 2, /* P */
+ 24, 2, /* mux */
+ BIT(31), /* gate */
+ 0);
+
+static SUNXI_CCU_MP_WITH_MUX_GATE(spi1_clk, "spi1", mod0_default_parents, 0x0a4,
+ 0, 4, /* M */
+ 16, 2, /* P */
+ 24, 2, /* mux */
+ BIT(31), /* gate */
+ 0);
+
+static const char * const i2s_parents[] = { "pll-audio-8x", "pll-audio-4x",
+ "pll-audio-2x", "pll-audio" };
+static SUNXI_CCU_MUX_WITH_GATE(i2s0_clk, "i2s0", i2s_parents,
+ 0x0b0, 16, 2, BIT(31), 0);
+
+static SUNXI_CCU_MUX_WITH_GATE(i2s1_clk, "i2s1", i2s_parents,
+ 0x0b4, 16, 2, BIT(31), 0);
+
+static SUNXI_CCU_MUX_WITH_GATE(i2s2_clk, "i2s2", i2s_parents,
+ 0x0b8, 16, 2, BIT(31), 0);
+
+static SUNXI_CCU_M_WITH_GATE(spdif_clk, "spdif", "pll-audio",
+ 0x0c0, 0, 4, BIT(31), 0);
+
+static SUNXI_CCU_GATE(usb_phy0_clk, "usb-phy0", "osc24M",
+ 0x0cc, BIT(8), 0);
+static SUNXI_CCU_GATE(usb_phy1_clk, "usb-phy1", "osc24M",
+ 0x0cc, BIT(9), 0);
+static SUNXI_CCU_GATE(usb_phy2_clk, "usb-phy2", "osc24M",
+ 0x0cc, BIT(10), 0);
+static SUNXI_CCU_GATE(usb_phy3_clk, "usb-phy3", "osc24M",
+ 0x0cc, BIT(11), 0);
+static SUNXI_CCU_GATE(usb_ohci0_clk, "usb-ohci0", "osc24M",
+ 0x0cc, BIT(16), 0);
+static SUNXI_CCU_GATE(usb_ohci1_clk, "usb-ohci1", "osc24M",
+ 0x0cc, BIT(17), 0);
+static SUNXI_CCU_GATE(usb_ohci2_clk, "usb-ohci2", "osc24M",
+ 0x0cc, BIT(18), 0);
+static SUNXI_CCU_GATE(usb_ohci3_clk, "usb-ohci3", "osc24M",
+ 0x0cc, BIT(19), 0);
+
+static const char * const dram_parents[] = { "pll-ddr", "pll-periph0-2x" };
+static SUNXI_CCU_M_WITH_MUX(dram_clk, "dram", dram_parents,
+ 0x0f4, 0, 4, 20, 2, CLK_IS_CRITICAL);
+
+static SUNXI_CCU_GATE(dram_ve_clk, "dram-ve", "dram",
+ 0x100, BIT(0), 0);
+static SUNXI_CCU_GATE(dram_csi_clk, "dram-csi", "dram",
+ 0x100, BIT(1), 0);
+static SUNXI_CCU_GATE(dram_deinterlace_clk, "dram-deinterlace", "dram",
+ 0x100, BIT(2), 0);
+static SUNXI_CCU_GATE(dram_ts_clk, "dram-ts", "dram",
+ 0x100, BIT(3), 0);
+
+static const char * const de_parents[] = { "pll-periph0-2x", "pll-de" };
+static SUNXI_CCU_M_WITH_MUX_GATE(de_clk, "de", de_parents,
+ 0x104, 0, 4, 24, 3, BIT(31), 0);
+
+static const char * const tcon_parents[] = { "pll-video" };
+static SUNXI_CCU_M_WITH_MUX_GATE(tcon_clk, "tcon", tcon_parents,
+ 0x118, 0, 4, 24, 3, BIT(31), 0);
+
+static const char * const tve_parents[] = { "pll-de", "pll-periph1" };
+static SUNXI_CCU_M_WITH_MUX_GATE(tve_clk, "tve", tve_parents,
+ 0x120, 0, 4, 24, 3, BIT(31), 0);
+
+static const char * const deinterlace_parents[] = { "pll-periph0", "pll-periph1" };
+static SUNXI_CCU_M_WITH_MUX_GATE(deinterlace_clk, "deinterlace", deinterlace_parents,
+ 0x124, 0, 4, 24, 3, BIT(31), 0);
+
+static SUNXI_CCU_GATE(csi_misc_clk, "csi-misc", "osc24M",
+ 0x130, BIT(31), 0);
+
+static const char * const csi_sclk_parents[] = { "pll-periph0", "pll-periph1" };
+static SUNXI_CCU_M_WITH_MUX_GATE(csi_sclk_clk, "csi-sclk", csi_sclk_parents,
+ 0x134, 16, 4, 24, 3, BIT(31), 0);
+
+static const char * const csi_mclk_parents[] = { "osc24M", "pll-video", "pll-periph0" };
+static SUNXI_CCU_M_WITH_MUX_GATE(csi_mclk_clk, "csi-mclk", csi_mclk_parents,
+ 0x134, 0, 5, 8, 3, BIT(15), 0);
+
+static SUNXI_CCU_M_WITH_GATE(ve_clk, "ve", "pll-ve",
+ 0x13c, 16, 3, BIT(31), 0);
+
+static SUNXI_CCU_GATE(ac_dig_clk, "ac-dig", "pll-audio",
+ 0x140, BIT(31), 0);
+static SUNXI_CCU_GATE(avs_clk, "avs", "osc24M",
+ 0x144, BIT(31), 0);
+
+static const char * const hdmi_parents[] = { "pll-video" };
+static SUNXI_CCU_M_WITH_MUX_GATE(hdmi_clk, "hdmi", hdmi_parents,
+ 0x150, 0, 4, 24, 2, BIT(31), 0);
+
+static SUNXI_CCU_GATE(hdmi_ddc_clk, "hdmi-ddc", "osc24M",
+ 0x154, BIT(31), 0);
+
+static const char * const mbus_parents[] = { "osc24M", "pll-periph0-2x", "pll-ddr" };
+static SUNXI_CCU_M_WITH_MUX_GATE(mbus_clk, "mbus", mbus_parents,
+ 0x15c, 0, 3, 24, 2, BIT(31), CLK_IS_CRITICAL);
+
+static SUNXI_CCU_M_WITH_GATE(gpu_clk, "gpu", "pll-gpu",
+ 0x1a0, 0, 3, BIT(31), 0);
+
+static struct ccu_common *sun8i_h3_ccu_clks[] = {
+ &pll_cpux_clk.common,
+ &pll_audio_base_clk.common,
+ &pll_video_clk.common,
+ &pll_ve_clk.common,
+ &pll_ddr_clk.common,
+ &pll_periph0_clk.common,
+ &pll_gpu_clk.common,
+ &pll_periph1_clk.common,
+ &pll_de_clk.common,
+ &cpux_clk.common,
+ &axi_clk.common,
+ &ahb1_clk.common,
+ &apb1_clk.common,
+ &apb2_clk.common,
+ &ahb2_clk.common,
+ &bus_ce_clk.common,
+ &bus_dma_clk.common,
+ &bus_mmc0_clk.common,
+ &bus_mmc1_clk.common,
+ &bus_mmc2_clk.common,
+ &bus_nand_clk.common,
+ &bus_dram_clk.common,
+ &bus_emac_clk.common,
+ &bus_ts_clk.common,
+ &bus_hstimer_clk.common,
+ &bus_spi0_clk.common,
+ &bus_spi1_clk.common,
+ &bus_otg_clk.common,
+ &bus_ehci0_clk.common,
+ &bus_ehci1_clk.common,
+ &bus_ehci2_clk.common,
+ &bus_ehci3_clk.common,
+ &bus_ohci0_clk.common,
+ &bus_ohci1_clk.common,
+ &bus_ohci2_clk.common,
+ &bus_ohci3_clk.common,
+ &bus_ve_clk.common,
+ &bus_tcon0_clk.common,
+ &bus_tcon1_clk.common,
+ &bus_deinterlace_clk.common,
+ &bus_csi_clk.common,
+ &bus_tve_clk.common,
+ &bus_hdmi_clk.common,
+ &bus_de_clk.common,
+ &bus_gpu_clk.common,
+ &bus_msgbox_clk.common,
+ &bus_spinlock_clk.common,
+ &bus_codec_clk.common,
+ &bus_spdif_clk.common,
+ &bus_pio_clk.common,
+ &bus_ths_clk.common,
+ &bus_i2s0_clk.common,
+ &bus_i2s1_clk.common,
+ &bus_i2s2_clk.common,
+ &bus_i2c0_clk.common,
+ &bus_i2c1_clk.common,
+ &bus_i2c2_clk.common,
+ &bus_uart0_clk.common,
+ &bus_uart1_clk.common,
+ &bus_uart2_clk.common,
+ &bus_uart3_clk.common,
+ &bus_scr_clk.common,
+ &bus_ephy_clk.common,
+ &bus_dbg_clk.common,
+ &ths_clk.common,
+ &nand_clk.common,
+ &mmc0_clk.common,
+ &mmc0_sample_clk.common,
+ &mmc0_output_clk.common,
+ &mmc1_clk.common,
+ &mmc1_sample_clk.common,
+ &mmc1_output_clk.common,
+ &mmc2_clk.common,
+ &mmc2_sample_clk.common,
+ &mmc2_output_clk.common,
+ &ts_clk.common,
+ &ce_clk.common,
+ &spi0_clk.common,
+ &spi1_clk.common,
+ &i2s0_clk.common,
+ &i2s1_clk.common,
+ &i2s2_clk.common,
+ &spdif_clk.common,
+ &usb_phy0_clk.common,
+ &usb_phy1_clk.common,
+ &usb_phy2_clk.common,
+ &usb_phy3_clk.common,
+ &usb_ohci0_clk.common,
+ &usb_ohci1_clk.common,
+ &usb_ohci2_clk.common,
+ &usb_ohci3_clk.common,
+ &dram_clk.common,
+ &dram_ve_clk.common,
+ &dram_csi_clk.common,
+ &dram_deinterlace_clk.common,
+ &dram_ts_clk.common,
+ &de_clk.common,
+ &tcon_clk.common,
+ &tve_clk.common,
+ &deinterlace_clk.common,
+ &csi_misc_clk.common,
+ &csi_sclk_clk.common,
+ &csi_mclk_clk.common,
+ &ve_clk.common,
+ &ac_dig_clk.common,
+ &avs_clk.common,
+ &hdmi_clk.common,
+ &hdmi_ddc_clk.common,
+ &mbus_clk.common,
+ &gpu_clk.common,
+};
+
+/* We hardcode the divider to 4 for now */
+static CLK_FIXED_FACTOR(pll_audio_clk, "pll-audio",
+ "pll-audio-base", 4, 1, CLK_SET_RATE_PARENT);
+static CLK_FIXED_FACTOR(pll_audio_2x_clk, "pll-audio-2x",
+ "pll-audio-base", 2, 1, CLK_SET_RATE_PARENT);
+static CLK_FIXED_FACTOR(pll_audio_4x_clk, "pll-audio-4x",
+ "pll-audio-base", 1, 1, CLK_SET_RATE_PARENT);
+static CLK_FIXED_FACTOR(pll_audio_8x_clk, "pll-audio-8x",
+ "pll-audio-base", 1, 2, CLK_SET_RATE_PARENT);
+static CLK_FIXED_FACTOR(pll_periph0_2x_clk, "pll-periph0-2x",
+ "pll-periph0", 1, 2, 0);
+
+static struct clk_hw_onecell_data sun8i_h3_hw_clks = {
+ .hws = {
+ [CLK_PLL_CPUX] = &pll_cpux_clk.common.hw,
+ [CLK_PLL_AUDIO_BASE] = &pll_audio_base_clk.common.hw,
+ [CLK_PLL_AUDIO] = &pll_audio_clk.hw,
+ [CLK_PLL_AUDIO_2X] = &pll_audio_2x_clk.hw,
+ [CLK_PLL_AUDIO_4X] = &pll_audio_4x_clk.hw,
+ [CLK_PLL_AUDIO_8X] = &pll_audio_8x_clk.hw,
+ [CLK_PLL_VIDEO] = &pll_video_clk.common.hw,
+ [CLK_PLL_VE] = &pll_ve_clk.common.hw,
+ [CLK_PLL_DDR] = &pll_ddr_clk.common.hw,
+ [CLK_PLL_PERIPH0] = &pll_periph0_clk.common.hw,
+ [CLK_PLL_PERIPH0_2X] = &pll_periph0_2x_clk.hw,
+ [CLK_PLL_GPU] = &pll_gpu_clk.common.hw,
+ [CLK_PLL_PERIPH1] = &pll_periph1_clk.common.hw,
+ [CLK_PLL_DE] = &pll_de_clk.common.hw,
+ [CLK_CPUX] = &cpux_clk.common.hw,
+ [CLK_AXI] = &axi_clk.common.hw,
+ [CLK_AHB1] = &ahb1_clk.common.hw,
+ [CLK_APB1] = &apb1_clk.common.hw,
+ [CLK_APB2] = &apb2_clk.common.hw,
+ [CLK_AHB2] = &ahb2_clk.common.hw,
+ [CLK_BUS_CE] = &bus_ce_clk.common.hw,
+ [CLK_BUS_DMA] = &bus_dma_clk.common.hw,
+ [CLK_BUS_MMC0] = &bus_mmc0_clk.common.hw,
+ [CLK_BUS_MMC1] = &bus_mmc1_clk.common.hw,
+ [CLK_BUS_MMC2] = &bus_mmc2_clk.common.hw,
+ [CLK_BUS_NAND] = &bus_nand_clk.common.hw,
+ [CLK_BUS_DRAM] = &bus_dram_clk.common.hw,
+ [CLK_BUS_EMAC] = &bus_emac_clk.common.hw,
+ [CLK_BUS_TS] = &bus_ts_clk.common.hw,
+ [CLK_BUS_HSTIMER] = &bus_hstimer_clk.common.hw,
+ [CLK_BUS_SPI0] = &bus_spi0_clk.common.hw,
+ [CLK_BUS_SPI1] = &bus_spi1_clk.common.hw,
+ [CLK_BUS_OTG] = &bus_otg_clk.common.hw,
+ [CLK_BUS_EHCI0] = &bus_ehci0_clk.common.hw,
+ [CLK_BUS_EHCI1] = &bus_ehci1_clk.common.hw,
+ [CLK_BUS_EHCI2] = &bus_ehci2_clk.common.hw,
+ [CLK_BUS_EHCI3] = &bus_ehci3_clk.common.hw,
+ [CLK_BUS_OHCI0] = &bus_ohci0_clk.common.hw,
+ [CLK_BUS_OHCI1] = &bus_ohci1_clk.common.hw,
+ [CLK_BUS_OHCI2] = &bus_ohci2_clk.common.hw,
+ [CLK_BUS_OHCI3] = &bus_ohci3_clk.common.hw,
+ [CLK_BUS_VE] = &bus_ve_clk.common.hw,
+ [CLK_BUS_TCON0] = &bus_tcon0_clk.common.hw,
+ [CLK_BUS_TCON1] = &bus_tcon1_clk.common.hw,
+ [CLK_BUS_DEINTERLACE] = &bus_deinterlace_clk.common.hw,
+ [CLK_BUS_CSI] = &bus_csi_clk.common.hw,
+ [CLK_BUS_TVE] = &bus_tve_clk.common.hw,
+ [CLK_BUS_HDMI] = &bus_hdmi_clk.common.hw,
+ [CLK_BUS_DE] = &bus_de_clk.common.hw,
+ [CLK_BUS_GPU] = &bus_gpu_clk.common.hw,
+ [CLK_BUS_MSGBOX] = &bus_msgbox_clk.common.hw,
+ [CLK_BUS_SPINLOCK] = &bus_spinlock_clk.common.hw,
+ [CLK_BUS_CODEC] = &bus_codec_clk.common.hw,
+ [CLK_BUS_SPDIF] = &bus_spdif_clk.common.hw,
+ [CLK_BUS_PIO] = &bus_pio_clk.common.hw,
+ [CLK_BUS_THS] = &bus_ths_clk.common.hw,
+ [CLK_BUS_I2S0] = &bus_i2s0_clk.common.hw,
+ [CLK_BUS_I2S1] = &bus_i2s1_clk.common.hw,
+ [CLK_BUS_I2S2] = &bus_i2s2_clk.common.hw,
+ [CLK_BUS_I2C0] = &bus_i2c0_clk.common.hw,
+ [CLK_BUS_I2C1] = &bus_i2c1_clk.common.hw,
+ [CLK_BUS_I2C2] = &bus_i2c2_clk.common.hw,
+ [CLK_BUS_UART0] = &bus_uart0_clk.common.hw,
+ [CLK_BUS_UART1] = &bus_uart1_clk.common.hw,
+ [CLK_BUS_UART2] = &bus_uart2_clk.common.hw,
+ [CLK_BUS_UART3] = &bus_uart3_clk.common.hw,
+ [CLK_BUS_SCR] = &bus_scr_clk.common.hw,
+ [CLK_BUS_EPHY] = &bus_ephy_clk.common.hw,
+ [CLK_BUS_DBG] = &bus_dbg_clk.common.hw,
+ [CLK_THS] = &ths_clk.common.hw,
+ [CLK_NAND] = &nand_clk.common.hw,
+ [CLK_MMC0] = &mmc0_clk.common.hw,
+ [CLK_MMC0_SAMPLE] = &mmc0_sample_clk.common.hw,
+ [CLK_MMC0_OUTPUT] = &mmc0_output_clk.common.hw,
+ [CLK_MMC1] = &mmc1_clk.common.hw,
+ [CLK_MMC1_SAMPLE] = &mmc1_sample_clk.common.hw,
+ [CLK_MMC1_OUTPUT] = &mmc1_output_clk.common.hw,
+ [CLK_MMC2] = &mmc2_clk.common.hw,
+ [CLK_MMC2_SAMPLE] = &mmc2_sample_clk.common.hw,
+ [CLK_MMC2_OUTPUT] = &mmc2_output_clk.common.hw,
+ [CLK_TS] = &ts_clk.common.hw,
+ [CLK_CE] = &ce_clk.common.hw,
+ [CLK_SPI0] = &spi0_clk.common.hw,
+ [CLK_SPI1] = &spi1_clk.common.hw,
+ [CLK_I2S0] = &i2s0_clk.common.hw,
+ [CLK_I2S1] = &i2s1_clk.common.hw,
+ [CLK_I2S2] = &i2s2_clk.common.hw,
+ [CLK_SPDIF] = &spdif_clk.common.hw,
+ [CLK_USB_PHY0] = &usb_phy0_clk.common.hw,
+ [CLK_USB_PHY1] = &usb_phy1_clk.common.hw,
+ [CLK_USB_PHY2] = &usb_phy2_clk.common.hw,
+ [CLK_USB_PHY3] = &usb_phy3_clk.common.hw,
+ [CLK_USB_OHCI0] = &usb_ohci0_clk.common.hw,
+ [CLK_USB_OHCI1] = &usb_ohci1_clk.common.hw,
+ [CLK_USB_OHCI2] = &usb_ohci2_clk.common.hw,
+ [CLK_USB_OHCI3] = &usb_ohci3_clk.common.hw,
+ [CLK_DRAM] = &dram_clk.common.hw,
+ [CLK_DRAM_VE] = &dram_ve_clk.common.hw,
+ [CLK_DRAM_CSI] = &dram_csi_clk.common.hw,
+ [CLK_DRAM_DEINTERLACE] = &dram_deinterlace_clk.common.hw,
+ [CLK_DRAM_TS] = &dram_ts_clk.common.hw,
+ [CLK_DE] = &de_clk.common.hw,
+ [CLK_TCON0] = &tcon_clk.common.hw,
+ [CLK_TVE] = &tve_clk.common.hw,
+ [CLK_DEINTERLACE] = &deinterlace_clk.common.hw,
+ [CLK_CSI_MISC] = &csi_misc_clk.common.hw,
+ [CLK_CSI_SCLK] = &csi_sclk_clk.common.hw,
+ [CLK_CSI_MCLK] = &csi_mclk_clk.common.hw,
+ [CLK_VE] = &ve_clk.common.hw,
+ [CLK_AC_DIG] = &ac_dig_clk.common.hw,
+ [CLK_AVS] = &avs_clk.common.hw,
+ [CLK_HDMI] = &hdmi_clk.common.hw,
+ [CLK_HDMI_DDC] = &hdmi_ddc_clk.common.hw,
+ [CLK_MBUS] = &mbus_clk.common.hw,
+ [CLK_GPU] = &gpu_clk.common.hw,
+ },
+ .num = CLK_NUMBER,
+};
+
+static struct ccu_reset_map sun8i_h3_ccu_resets[] = {
+ [RST_USB_PHY0] = { 0x0cc, BIT(0) },
+ [RST_USB_PHY1] = { 0x0cc, BIT(1) },
+ [RST_USB_PHY2] = { 0x0cc, BIT(2) },
+ [RST_USB_PHY3] = { 0x0cc, BIT(3) },
+
+ [RST_MBUS] = { 0x0fc, BIT(31) },
+
+ [RST_BUS_CE] = { 0x2c0, BIT(5) },
+ [RST_BUS_DMA] = { 0x2c0, BIT(6) },
+ [RST_BUS_MMC0] = { 0x2c0, BIT(8) },
+ [RST_BUS_MMC1] = { 0x2c0, BIT(9) },
+ [RST_BUS_MMC2] = { 0x2c0, BIT(10) },
+ [RST_BUS_NAND] = { 0x2c0, BIT(13) },
+ [RST_BUS_DRAM] = { 0x2c0, BIT(14) },
+ [RST_BUS_EMAC] = { 0x2c0, BIT(17) },
+ [RST_BUS_TS] = { 0x2c0, BIT(18) },
+ [RST_BUS_HSTIMER] = { 0x2c0, BIT(19) },
+ [RST_BUS_SPI0] = { 0x2c0, BIT(20) },
+ [RST_BUS_SPI1] = { 0x2c0, BIT(21) },
+ [RST_BUS_OTG] = { 0x2c0, BIT(23) },
+ [RST_BUS_EHCI0] = { 0x2c0, BIT(24) },
+ [RST_BUS_EHCI1] = { 0x2c0, BIT(25) },
+ [RST_BUS_EHCI2] = { 0x2c0, BIT(26) },
+ [RST_BUS_EHCI3] = { 0x2c0, BIT(27) },
+ [RST_BUS_OHCI0] = { 0x2c0, BIT(28) },
+ [RST_BUS_OHCI1] = { 0x2c0, BIT(29) },
+ [RST_BUS_OHCI2] = { 0x2c0, BIT(30) },
+ [RST_BUS_OHCI3] = { 0x2c0, BIT(31) },
+
+ [RST_BUS_VE] = { 0x2c4, BIT(0) },
+ [RST_BUS_TCON0] = { 0x2c4, BIT(3) },
+ [RST_BUS_TCON1] = { 0x2c4, BIT(4) },
+ [RST_BUS_DEINTERLACE] = { 0x2c4, BIT(5) },
+ [RST_BUS_CSI] = { 0x2c4, BIT(8) },
+ [RST_BUS_TVE] = { 0x2c4, BIT(9) },
+ [RST_BUS_HDMI0] = { 0x2c4, BIT(10) },
+ [RST_BUS_HDMI1] = { 0x2c4, BIT(11) },
+ [RST_BUS_DE] = { 0x2c4, BIT(12) },
+ [RST_BUS_GPU] = { 0x2c4, BIT(20) },
+ [RST_BUS_MSGBOX] = { 0x2c4, BIT(21) },
+ [RST_BUS_SPINLOCK] = { 0x2c4, BIT(22) },
+ [RST_BUS_DBG] = { 0x2c4, BIT(31) },
+
+ [RST_BUS_EPHY] = { 0x2c8, BIT(2) },
+
+ [RST_BUS_CODEC] = { 0x2d0, BIT(0) },
+ [RST_BUS_SPDIF] = { 0x2d0, BIT(1) },
+ [RST_BUS_THS] = { 0x2d0, BIT(8) },
+ [RST_BUS_I2S0] = { 0x2d0, BIT(12) },
+ [RST_BUS_I2S1] = { 0x2d0, BIT(13) },
+ [RST_BUS_I2S2] = { 0x2d0, BIT(14) },
+
+ [RST_BUS_I2C0] = { 0x2d4, BIT(0) },
+ [RST_BUS_I2C1] = { 0x2d4, BIT(1) },
+ [RST_BUS_I2C2] = { 0x2d4, BIT(2) },
+ [RST_BUS_UART0] = { 0x2d4, BIT(16) },
+ [RST_BUS_UART1] = { 0x2d4, BIT(17) },
+ [RST_BUS_UART2] = { 0x2d4, BIT(18) },
+ [RST_BUS_UART3] = { 0x2d4, BIT(19) },
+ [RST_BUS_SCR] = { 0x2d4, BIT(20) },
+};
+
+static const struct sunxi_ccu_desc sun8i_h3_ccu_desc = {
+ .ccu_clks = sun8i_h3_ccu_clks,
+ .num_ccu_clks = ARRAY_SIZE(sun8i_h3_ccu_clks),
+
+ .hw_clks = &sun8i_h3_hw_clks,
+
+ .resets = sun8i_h3_ccu_resets,
+ .num_resets = ARRAY_SIZE(sun8i_h3_ccu_resets),
+};
+
+static void __init sun8i_h3_ccu_setup(struct device_node *node)
+{
+ void __iomem *reg;
+ u32 val;
+
+ reg = of_io_request_and_map(node, 0, of_node_full_name(node));
+ if (IS_ERR(reg)) {
+ pr_err("%s: Could not map the clock registers\n",
+ of_node_full_name(node));
+ return;
+ }
+
+ /* Force the PLL-Audio-1x divider to 4 */
+ val = readl(reg + SUN8I_H3_PLL_AUDIO_REG);
+ val &= ~GENMASK(4, 0);
+ writel(val | 3, reg + SUN8I_H3_PLL_AUDIO_REG);
+
+ sunxi_ccu_probe(node, reg, &sun8i_h3_ccu_desc);
+}
+CLK_OF_DECLARE(sun8i_h3_ccu, "allwinner,sun8i-h3-ccu",
+ sun8i_h3_ccu_setup);
diff --git a/drivers/clk/sunxi-ng/ccu-sun8i-h3.h b/drivers/clk/sunxi-ng/ccu-sun8i-h3.h
new file mode 100644
index 000000000000..78be712c7487
--- /dev/null
+++ b/drivers/clk/sunxi-ng/ccu-sun8i-h3.h
@@ -0,0 +1,62 @@
+/*
+ * Copyright 2016 Maxime Ripard
+ *
+ * Maxime Ripard <maxime.ripard@free-electrons.com>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ */
+
+#ifndef _CCU_SUN8I_H3_H_
+#define _CCU_SUN8I_H3_H_
+
+#include <dt-bindings/clock/sun8i-h3-ccu.h>
+#include <dt-bindings/reset/sun8i-h3-ccu.h>
+
+#define CLK_PLL_CPUX 0
+#define CLK_PLL_AUDIO_BASE 1
+#define CLK_PLL_AUDIO 2
+#define CLK_PLL_AUDIO_2X 3
+#define CLK_PLL_AUDIO_4X 4
+#define CLK_PLL_AUDIO_8X 5
+#define CLK_PLL_VIDEO 6
+#define CLK_PLL_VE 7
+#define CLK_PLL_DDR 8
+#define CLK_PLL_PERIPH0 9
+#define CLK_PLL_PERIPH0_2X 10
+#define CLK_PLL_GPU 11
+#define CLK_PLL_PERIPH1 12
+#define CLK_PLL_DE 13
+
+/* The CPUX clock is exported */
+
+#define CLK_AXI 15
+#define CLK_AHB1 16
+#define CLK_APB1 17
+#define CLK_APB2 18
+#define CLK_AHB2 19
+
+/* All the bus gates are exported */
+
+/* The first bunch of module clocks are exported */
+
+#define CLK_DRAM 96
+
+/* All the DRAM gates are exported */
+
+/* Some more module clocks are exported */
+
+#define CLK_MBUS 113
+
+/* And the GPU module clock is exported */
+
+#define CLK_NUMBER (CLK_GPU + 1)
+
+#endif /* _CCU_SUN8I_H3_H_ */
diff --git a/include/dt-bindings/clock/sun8i-h3-ccu.h b/include/dt-bindings/clock/sun8i-h3-ccu.h
new file mode 100644
index 000000000000..efb7ba2bd515
--- /dev/null
+++ b/include/dt-bindings/clock/sun8i-h3-ccu.h
@@ -0,0 +1,145 @@
+/*
+ * Copyright (C) 2016 Maxime Ripard <maxime.ripard@free-electrons.com>
+ *
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPL or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
+ *
+ * a) This file is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of the
+ * License, or (at your option) any later version.
+ *
+ * This file is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * Or, alternatively,
+ *
+ * b) Permission is hereby granted, free of charge, to any person
+ * obtaining a copy of this software and associated documentation
+ * files (the "Software"), to deal in the Software without
+ * restriction, including without limitation the rights to use,
+ * copy, modify, merge, publish, distribute, sublicense, and/or
+ * sell copies of the Software, and to permit persons to whom the
+ * Software is furnished to do so, subject to the following
+ * conditions:
+ *
+ * The above copyright notice and this permission notice shall be
+ * included in all copies or substantial portions of the Software.
+ *
+ * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
+ * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
+ * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ * OTHER DEALINGS IN THE SOFTWARE.
+ */
+
+#ifndef _DT_BINDINGS_CLK_SUN8I_H3_H_
+#define _DT_BINDINGS_CLK_SUN8I_H3_H_
+
+#define CLK_CPUX 14
+
+#define CLK_BUS_CE 20
+#define CLK_BUS_DMA 21
+#define CLK_BUS_MMC0 22
+#define CLK_BUS_MMC1 23
+#define CLK_BUS_MMC2 24
+#define CLK_BUS_NAND 25
+#define CLK_BUS_DRAM 26
+#define CLK_BUS_EMAC 27
+#define CLK_BUS_TS 28
+#define CLK_BUS_HSTIMER 29
+#define CLK_BUS_SPI0 30
+#define CLK_BUS_SPI1 31
+#define CLK_BUS_OTG 32
+#define CLK_BUS_EHCI0 33
+#define CLK_BUS_EHCI1 34
+#define CLK_BUS_EHCI2 35
+#define CLK_BUS_EHCI3 36
+#define CLK_BUS_OHCI0 37
+#define CLK_BUS_OHCI1 38
+#define CLK_BUS_OHCI2 39
+#define CLK_BUS_OHCI3 40
+#define CLK_BUS_VE 41
+#define CLK_BUS_TCON0 42
+#define CLK_BUS_TCON1 43
+#define CLK_BUS_DEINTERLACE 44
+#define CLK_BUS_CSI 45
+#define CLK_BUS_TVE 46
+#define CLK_BUS_HDMI 47
+#define CLK_BUS_DE 48
+#define CLK_BUS_GPU 49
+#define CLK_BUS_MSGBOX 50
+#define CLK_BUS_SPINLOCK 51
+#define CLK_BUS_CODEC 52
+#define CLK_BUS_SPDIF 53
+#define CLK_BUS_PIO 54
+#define CLK_BUS_THS 55
+#define CLK_BUS_I2S0 56
+#define CLK_BUS_I2S1 57
+#define CLK_BUS_I2S2 58
+#define CLK_BUS_I2C0 59
+#define CLK_BUS_I2C1 60
+#define CLK_BUS_I2C2 61
+#define CLK_BUS_UART0 62
+#define CLK_BUS_UART1 63
+#define CLK_BUS_UART2 64
+#define CLK_BUS_UART3 65
+#define CLK_BUS_SCR 66
+#define CLK_BUS_EPHY 67
+#define CLK_BUS_DBG 68
+
+#define CLK_THS 69
+#define CLK_NAND 70
+#define CLK_MMC0 71
+#define CLK_MMC0_SAMPLE 72
+#define CLK_MMC0_OUTPUT 73
+#define CLK_MMC1 74
+#define CLK_MMC1_SAMPLE 75
+#define CLK_MMC1_OUTPUT 76
+#define CLK_MMC2 77
+#define CLK_MMC2_SAMPLE 78
+#define CLK_MMC2_OUTPUT 79
+#define CLK_TS 80
+#define CLK_CE 81
+#define CLK_SPI0 82
+#define CLK_SPI1 83
+#define CLK_I2S0 84
+#define CLK_I2S1 85
+#define CLK_I2S2 86
+#define CLK_SPDIF 87
+#define CLK_USB_PHY0 88
+#define CLK_USB_PHY1 89
+#define CLK_USB_PHY2 90
+#define CLK_USB_PHY3 91
+#define CLK_USB_OHCI0 92
+#define CLK_USB_OHCI1 93
+#define CLK_USB_OHCI2 94
+#define CLK_USB_OHCI3 95
+
+#define CLK_DRAM_VE 97
+#define CLK_DRAM_CSI 98
+#define CLK_DRAM_DEINTERLACE 99
+#define CLK_DRAM_TS 100
+#define CLK_DE 101
+#define CLK_TCON0 102
+#define CLK_TVE 103
+#define CLK_DEINTERLACE 104
+#define CLK_CSI_MISC 105
+#define CLK_CSI_SCLK 106
+#define CLK_CSI_MCLK 107
+#define CLK_VE 108
+#define CLK_AC_DIG 109
+#define CLK_AVS 110
+#define CLK_HDMI 111
+#define CLK_HDMI_DDC 112
+
+#define CLK_GPU 114
+
+#endif /* _DT_BINDINGS_CLK_SUN8I_H3_H_ */
diff --git a/include/dt-bindings/reset/sun8i-h3-ccu.h b/include/dt-bindings/reset/sun8i-h3-ccu.h
new file mode 100644
index 000000000000..6b7af80c26ec
--- /dev/null
+++ b/include/dt-bindings/reset/sun8i-h3-ccu.h
@@ -0,0 +1,103 @@
+/*
+ * Copyright (C) 2016 Maxime Ripard <maxime.ripard@free-electrons.com>
+ *
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPL or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
+ *
+ * a) This file is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of the
+ * License, or (at your option) any later version.
+ *
+ * This file is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * Or, alternatively,
+ *
+ * b) Permission is hereby granted, free of charge, to any person
+ * obtaining a copy of this software and associated documentation
+ * files (the "Software"), to deal in the Software without
+ * restriction, including without limitation the rights to use,
+ * copy, modify, merge, publish, distribute, sublicense, and/or
+ * sell copies of the Software, and to permit persons to whom the
+ * Software is furnished to do so, subject to the following
+ * conditions:
+ *
+ * The above copyright notice and this permission notice shall be
+ * included in all copies or substantial portions of the Software.
+ *
+ * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
+ * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
+ * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ * OTHER DEALINGS IN THE SOFTWARE.
+ */
+
+#ifndef _DT_BINDINGS_RST_SUN8I_H3_H_
+#define _DT_BINDINGS_RST_SUN8I_H3_H_
+
+#define RST_USB_PHY0 0
+#define RST_USB_PHY1 1
+#define RST_USB_PHY2 2
+#define RST_USB_PHY3 3
+
+#define RST_MBUS 4
+
+#define RST_BUS_CE 5
+#define RST_BUS_DMA 6
+#define RST_BUS_MMC0 7
+#define RST_BUS_MMC1 8
+#define RST_BUS_MMC2 9
+#define RST_BUS_NAND 10
+#define RST_BUS_DRAM 11
+#define RST_BUS_EMAC 12
+#define RST_BUS_TS 13
+#define RST_BUS_HSTIMER 14
+#define RST_BUS_SPI0 15
+#define RST_BUS_SPI1 16
+#define RST_BUS_OTG 17
+#define RST_BUS_EHCI0 18
+#define RST_BUS_EHCI1 19
+#define RST_BUS_EHCI2 20
+#define RST_BUS_EHCI3 21
+#define RST_BUS_OHCI0 22
+#define RST_BUS_OHCI1 23
+#define RST_BUS_OHCI2 24
+#define RST_BUS_OHCI3 25
+#define RST_BUS_VE 26
+#define RST_BUS_TCON0 27
+#define RST_BUS_TCON1 28
+#define RST_BUS_DEINTERLACE 29
+#define RST_BUS_CSI 30
+#define RST_BUS_TVE 31
+#define RST_BUS_HDMI0 32
+#define RST_BUS_HDMI1 33
+#define RST_BUS_DE 34
+#define RST_BUS_GPU 35
+#define RST_BUS_MSGBOX 36
+#define RST_BUS_SPINLOCK 37
+#define RST_BUS_DBG 38
+#define RST_BUS_EPHY 39
+#define RST_BUS_CODEC 40
+#define RST_BUS_SPDIF 41
+#define RST_BUS_THS 42
+#define RST_BUS_I2S0 43
+#define RST_BUS_I2S1 44
+#define RST_BUS_I2S2 45
+#define RST_BUS_I2C0 46
+#define RST_BUS_I2C1 47
+#define RST_BUS_I2C2 48
+#define RST_BUS_UART0 49
+#define RST_BUS_UART1 50
+#define RST_BUS_UART2 51
+#define RST_BUS_UART3 52
+#define RST_BUS_SCR 53
+
+#endif /* _DT_BINDINGS_RST_SUN8I_H3_H_ */
--
2.9.0
^ permalink raw reply related [flat|nested] 22+ messages in thread
* Re: [PATCH v3 13/14] clk: sunxi-ng: Add H3 clocks
2016-06-29 19:05 ` [PATCH v3 13/14] clk: sunxi-ng: Add H3 clocks Maxime Ripard
@ 2016-06-30 8:31 ` Jean-Francois Moine
2016-07-07 2:33 ` Michael Turquette
1 sibling, 0 replies; 22+ messages in thread
From: Jean-Francois Moine @ 2016-06-30 8:31 UTC (permalink / raw)
To: Maxime Ripard
Cc: Mike Turquette, Stephen Boyd, Chen-Yu Tsai, linux-clk,
Hans de Goede, Boris Brezillon, Rob Herring, Vishnu Patekar,
linux-arm-kernel, linux-kernel, devicetree
On Wed, 29 Jun 2016 21:05:34 +0200
Maxime Ripard <maxime.ripard@free-electrons.com> wrote:
> +static void __init sun8i_h3_ccu_setup(struct device_node *node)
> +{
> + void __iomem *reg;
> + u32 val;
> +
> + reg =3D of_io_request_and_map(node, 0, of_node_full_name(node));
> + if (IS_ERR(reg)) {
> + pr_err("%s: Could not map the clock registers\n",
> + of_node_full_name(node));
> + return;
> + }
> +
> + /* Force the PLL-Audio-1x divider to 4 */
> + val =3D readl(reg + SUN8I_H3_PLL_AUDIO_REG);
> + val &=3D ~GENMASK(4, 0);
> + writel(val | 3, reg + SUN8I_H3_PLL_AUDIO_REG);
> +
> + sunxi_ccu_probe(node, reg, &sun8i_h3_ccu_desc);
> +}
FYI, the pll-audio PLL_POST_DIV is 19:16.
--=20
Ken ar c'henta=F1 | ** Breizh ha Linux atav! **
Jef | http://moinejf.free.fr/
^ permalink raw reply [flat|nested] 22+ messages in thread
* Re: [PATCH v3 13/14] clk: sunxi-ng: Add H3 clocks
2016-06-29 19:05 ` [PATCH v3 13/14] clk: sunxi-ng: Add H3 clocks Maxime Ripard
2016-06-30 8:31 ` Jean-Francois Moine
@ 2016-07-07 2:33 ` Michael Turquette
2016-07-08 21:35 ` Maxime Ripard
1 sibling, 1 reply; 22+ messages in thread
From: Michael Turquette @ 2016-07-07 2:33 UTC (permalink / raw)
To: Maxime Ripard, Stephen Boyd, Chen-Yu Tsai
Cc: linux-clk, Hans de Goede, Boris Brezillon, Rob Herring,
Vishnu Patekar, linux-arm-kernel, linux-kernel, devicetree,
Jean-Francois Moine, Maxime Ripard
Hi Maxime,
Quoting Maxime Ripard (2016-06-29 12:05:34)
> +static void __init sun8i_h3_ccu_setup(struct device_node *node)
> +{
> + void __iomem *reg;
> + u32 val;
> +
> + reg =3D of_io_request_and_map(node, 0, of_node_full_name(node));
> + if (IS_ERR(reg)) {
> + pr_err("%s: Could not map the clock registers\n",
> + of_node_full_name(node));
> + return;
> + }
> +
> + /* Force the PLL-Audio-1x divider to 4 */
> + val =3D readl(reg + SUN8I_H3_PLL_AUDIO_REG);
> + val &=3D ~GENMASK(4, 0);
> + writel(val | 3, reg + SUN8I_H3_PLL_AUDIO_REG);
> +
> + sunxi_ccu_probe(node, reg, &sun8i_h3_ccu_desc);
> +}
> +CLK_OF_DECLARE(sun8i_h3_ccu, "allwinner,sun8i-h3-ccu",
> + sun8i_h3_ccu_setup);
There are several examples of drivers that split the clocks between
"early" CLK_OF_DECLARE clocks and "late" module clocks. If you really
need early clocks (which is less likely on a 64-bit platform with
architected timers), it would be nice to pair that with a proper
platform_driver (using builtin_platform_driver most likely).
Otherwise that is my only nitpick with this series. Looks good!
Best regards,
Mike
^ permalink raw reply [flat|nested] 22+ messages in thread
* Re: [PATCH v3 13/14] clk: sunxi-ng: Add H3 clocks
2016-07-07 2:33 ` Michael Turquette
@ 2016-07-08 21:35 ` Maxime Ripard
2016-07-09 1:17 ` Michael Turquette
0 siblings, 1 reply; 22+ messages in thread
From: Maxime Ripard @ 2016-07-08 21:35 UTC (permalink / raw)
To: Michael Turquette
Cc: Stephen Boyd, Chen-Yu Tsai, linux-clk, Hans de Goede,
Boris Brezillon, Rob Herring, Vishnu Patekar, linux-arm-kernel,
linux-kernel, devicetree, Jean-Francois Moine
[-- Attachment #1: Type: text/plain, Size: 1660 bytes --]
Hi Mike,
On Wed, Jul 06, 2016 at 07:33:08PM -0700, Michael Turquette wrote:
> Hi Maxime,
>
> Quoting Maxime Ripard (2016-06-29 12:05:34)
> > +static void __init sun8i_h3_ccu_setup(struct device_node *node)
> > +{
> > + void __iomem *reg;
> > + u32 val;
> > +
> > + reg = of_io_request_and_map(node, 0, of_node_full_name(node));
> > + if (IS_ERR(reg)) {
> > + pr_err("%s: Could not map the clock registers\n",
> > + of_node_full_name(node));
> > + return;
> > + }
> > +
> > + /* Force the PLL-Audio-1x divider to 4 */
> > + val = readl(reg + SUN8I_H3_PLL_AUDIO_REG);
> > + val &= ~GENMASK(4, 0);
> > + writel(val | 3, reg + SUN8I_H3_PLL_AUDIO_REG);
> > +
> > + sunxi_ccu_probe(node, reg, &sun8i_h3_ccu_desc);
> > +}
> > +CLK_OF_DECLARE(sun8i_h3_ccu, "allwinner,sun8i-h3-ccu",
> > + sun8i_h3_ccu_setup);
>
> There are several examples of drivers that split the clocks between
> "early" CLK_OF_DECLARE clocks and "late" module clocks. If you really
> need early clocks (which is less likely on a 64-bit platform with
> architected timers), it would be nice to pair that with a proper
> platform_driver (using builtin_platform_driver most likely).
I think we discussed that already, but yeah, we do have timers that
are not the architected ones (and this is a ARMv7 platform). I have
the feeling that splitting the two doesn't really bring any benefit,
but complexify a lot the driver.
Maxime
--
Maxime Ripard, Free Electrons
Embedded Linux and Kernel engineering
http://free-electrons.com
[-- Attachment #2: signature.asc --]
[-- Type: application/pgp-signature, Size: 819 bytes --]
^ permalink raw reply [flat|nested] 22+ messages in thread
* Re: [PATCH v3 13/14] clk: sunxi-ng: Add H3 clocks
2016-07-08 21:35 ` Maxime Ripard
@ 2016-07-09 1:17 ` Michael Turquette
2016-07-11 20:26 ` Maxime Ripard
0 siblings, 1 reply; 22+ messages in thread
From: Michael Turquette @ 2016-07-09 1:17 UTC (permalink / raw)
To: Maxime Ripard
Cc: Stephen Boyd, Chen-Yu Tsai, linux-clk, Hans de Goede,
Boris Brezillon, Rob Herring, Vishnu Patekar, linux-arm-kernel,
linux-kernel, devicetree, Jean-Francois Moine
Quoting Maxime Ripard (2016-07-08 14:35:06)
> Hi Mike,
> =
> On Wed, Jul 06, 2016 at 07:33:08PM -0700, Michael Turquette wrote:
> > Hi Maxime,
> > =
> > Quoting Maxime Ripard (2016-06-29 12:05:34)
> > > +static void __init sun8i_h3_ccu_setup(struct device_node *node)
> > > +{
> > > + void __iomem *reg;
> > > + u32 val;
> > > +
> > > + reg =3D of_io_request_and_map(node, 0, of_node_full_name(node=
));
> > > + if (IS_ERR(reg)) {
> > > + pr_err("%s: Could not map the clock registers\n",
> > > + of_node_full_name(node));
> > > + return;
> > > + }
> > > +
> > > + /* Force the PLL-Audio-1x divider to 4 */
> > > + val =3D readl(reg + SUN8I_H3_PLL_AUDIO_REG);
> > > + val &=3D ~GENMASK(4, 0);
> > > + writel(val | 3, reg + SUN8I_H3_PLL_AUDIO_REG);
> > > +
> > > + sunxi_ccu_probe(node, reg, &sun8i_h3_ccu_desc);
> > > +}
> > > +CLK_OF_DECLARE(sun8i_h3_ccu, "allwinner,sun8i-h3-ccu",
> > > + sun8i_h3_ccu_setup);
> > =
> > There are several examples of drivers that split the clocks between
> > "early" CLK_OF_DECLARE clocks and "late" module clocks. If you really
> > need early clocks (which is less likely on a 64-bit platform with
> > architected timers), it would be nice to pair that with a proper
> > platform_driver (using builtin_platform_driver most likely).
> =
> I think we discussed that already, but yeah, we do have timers that
> are not the architected ones (and this is a ARMv7 platform). I have
> the feeling that splitting the two doesn't really bring any benefit,
> but complexify a lot the driver.
Cool. I've pushed patches 1-13 to the clk tree under a shared, immutable
branch: clk-sunxi-ng
I've merged this branch into clk-next to get some soak testing.
I did not merge patch #14. Feel free to add my reviewed-by to that
patch.
Were you going to spin another version? If so I can replace v3 with v4
when it is ready. Thanks again for your hard work on this! Very happy to
see the binding be reworked :-)
Regards,
Mike
> =
> Maxime
> =
> -- =
> Maxime Ripard, Free Electrons
> Embedded Linux and Kernel engineering
> http://free-electrons.com
^ permalink raw reply [flat|nested] 22+ messages in thread
* Re: [PATCH v3 13/14] clk: sunxi-ng: Add H3 clocks
2016-07-09 1:17 ` Michael Turquette
@ 2016-07-11 20:26 ` Maxime Ripard
2016-07-11 21:41 ` Michael Turquette
0 siblings, 1 reply; 22+ messages in thread
From: Maxime Ripard @ 2016-07-11 20:26 UTC (permalink / raw)
To: Michael Turquette
Cc: Stephen Boyd, Chen-Yu Tsai, linux-clk, Hans de Goede,
Boris Brezillon, Rob Herring, Vishnu Patekar, linux-arm-kernel,
linux-kernel, devicetree, Jean-Francois Moine
[-- Attachment #1: Type: text/plain, Size: 2685 bytes --]
Hi Mike,
On Fri, Jul 08, 2016 at 06:17:16PM -0700, Michael Turquette wrote:
> Quoting Maxime Ripard (2016-07-08 14:35:06)
> > Hi Mike,
> >
> > On Wed, Jul 06, 2016 at 07:33:08PM -0700, Michael Turquette wrote:
> > > Hi Maxime,
> > >
> > > Quoting Maxime Ripard (2016-06-29 12:05:34)
> > > > +static void __init sun8i_h3_ccu_setup(struct device_node *node)
> > > > +{
> > > > + void __iomem *reg;
> > > > + u32 val;
> > > > +
> > > > + reg = of_io_request_and_map(node, 0, of_node_full_name(node));
> > > > + if (IS_ERR(reg)) {
> > > > + pr_err("%s: Could not map the clock registers\n",
> > > > + of_node_full_name(node));
> > > > + return;
> > > > + }
> > > > +
> > > > + /* Force the PLL-Audio-1x divider to 4 */
> > > > + val = readl(reg + SUN8I_H3_PLL_AUDIO_REG);
> > > > + val &= ~GENMASK(4, 0);
> > > > + writel(val | 3, reg + SUN8I_H3_PLL_AUDIO_REG);
> > > > +
> > > > + sunxi_ccu_probe(node, reg, &sun8i_h3_ccu_desc);
> > > > +}
> > > > +CLK_OF_DECLARE(sun8i_h3_ccu, "allwinner,sun8i-h3-ccu",
> > > > + sun8i_h3_ccu_setup);
> > >
> > > There are several examples of drivers that split the clocks between
> > > "early" CLK_OF_DECLARE clocks and "late" module clocks. If you really
> > > need early clocks (which is less likely on a 64-bit platform with
> > > architected timers), it would be nice to pair that with a proper
> > > platform_driver (using builtin_platform_driver most likely).
> >
> > I think we discussed that already, but yeah, we do have timers that
> > are not the architected ones (and this is a ARMv7 platform). I have
> > the feeling that splitting the two doesn't really bring any benefit,
> > but complexify a lot the driver.
>
> Cool. I've pushed patches 1-13 to the clk tree under a shared, immutable
> branch: clk-sunxi-ng
>
> I've merged this branch into clk-next to get some soak testing.
>
> I did not merge patch #14. Feel free to add my reviewed-by to that
> patch.
Thanks for merging the other patches, but can you merge patch 14 too?
Merging it through my tree would break bisectability, and it should
apply properly on your tree.
> Were you going to spin another version? If so I can replace v3 with v4
> when it is ready. Thanks again for your hard work on this! Very happy to
> see the binding be reworked :-)
I'll send another patch to fix the bug found by Jean-Francois, and one
to fix a typo. Feel free to squash them in.
Thanks!
Maxime
--
Maxime Ripard, Free Electrons
Embedded Linux and Kernel engineering
http://free-electrons.com
[-- Attachment #2: signature.asc --]
[-- Type: application/pgp-signature, Size: 819 bytes --]
^ permalink raw reply [flat|nested] 22+ messages in thread
* Re: [PATCH v3 13/14] clk: sunxi-ng: Add H3 clocks
2016-07-11 20:26 ` Maxime Ripard
@ 2016-07-11 21:41 ` Michael Turquette
0 siblings, 0 replies; 22+ messages in thread
From: Michael Turquette @ 2016-07-11 21:41 UTC (permalink / raw)
To: Maxime Ripard
Cc: Stephen Boyd, Chen-Yu Tsai, linux-clk, Hans de Goede,
Boris Brezillon, Rob Herring, Vishnu Patekar, linux-arm-kernel,
linux-kernel, devicetree, Jean-Francois Moine
Quoting Maxime Ripard (2016-07-11 13:26:32)
> Hi Mike,
> =
> On Fri, Jul 08, 2016 at 06:17:16PM -0700, Michael Turquette wrote:
> > Quoting Maxime Ripard (2016-07-08 14:35:06)
> > > Hi Mike,
> > > =
> > > On Wed, Jul 06, 2016 at 07:33:08PM -0700, Michael Turquette wrote:
> > > > Hi Maxime,
> > > > =
> > > > Quoting Maxime Ripard (2016-06-29 12:05:34)
> > > > > +static void __init sun8i_h3_ccu_setup(struct device_node *node)
> > > > > +{
> > > > > + void __iomem *reg;
> > > > > + u32 val;
> > > > > +
> > > > > + reg =3D of_io_request_and_map(node, 0, of_node_full_name(=
node));
> > > > > + if (IS_ERR(reg)) {
> > > > > + pr_err("%s: Could not map the clock registers\n",
> > > > > + of_node_full_name(node));
> > > > > + return;
> > > > > + }
> > > > > +
> > > > > + /* Force the PLL-Audio-1x divider to 4 */
> > > > > + val =3D readl(reg + SUN8I_H3_PLL_AUDIO_REG);
> > > > > + val &=3D ~GENMASK(4, 0);
> > > > > + writel(val | 3, reg + SUN8I_H3_PLL_AUDIO_REG);
> > > > > +
> > > > > + sunxi_ccu_probe(node, reg, &sun8i_h3_ccu_desc);
> > > > > +}
> > > > > +CLK_OF_DECLARE(sun8i_h3_ccu, "allwinner,sun8i-h3-ccu",
> > > > > + sun8i_h3_ccu_setup);
> > > > =
> > > > There are several examples of drivers that split the clocks between
> > > > "early" CLK_OF_DECLARE clocks and "late" module clocks. If you real=
ly
> > > > need early clocks (which is less likely on a 64-bit platform with
> > > > architected timers), it would be nice to pair that with a proper
> > > > platform_driver (using builtin_platform_driver most likely).
> > > =
> > > I think we discussed that already, but yeah, we do have timers that
> > > are not the architected ones (and this is a ARMv7 platform). I have
> > > the feeling that splitting the two doesn't really bring any benefit,
> > > but complexify a lot the driver.
> > =
> > Cool. I've pushed patches 1-13 to the clk tree under a shared, immutable
> > branch: clk-sunxi-ng
> > =
> > I've merged this branch into clk-next to get some soak testing.
> > =
> > I did not merge patch #14. Feel free to add my reviewed-by to that
> > patch.
> =
> Thanks for merging the other patches, but can you merge patch 14 too?
> Merging it through my tree would break bisectability, and it should
> apply properly on your tree.
Applied.
Regards,
Mike
> =
> > Were you going to spin another version? If so I can replace v3 with v4
> > when it is ready. Thanks again for your hard work on this! Very happy to
> > see the binding be reworked :-)
> =
> I'll send another patch to fix the bug found by Jean-Francois, and one
> to fix a typo. Feel free to squash them in.
> =
> Thanks!
> Maxime
> =
> -- =
> Maxime Ripard, Free Electrons
> Embedded Linux and Kernel engineering
> http://free-electrons.com
^ permalink raw reply [flat|nested] 22+ messages in thread
* [PATCH v3 14/14] ARM: dt: sun8i: switch the H3 to the new CCU driver
2016-06-29 19:05 [PATCH v3 00/14] clk: sunxi: introduce "modern" clock support Maxime Ripard
` (12 preceding siblings ...)
2016-06-29 19:05 ` [PATCH v3 13/14] clk: sunxi-ng: Add H3 clocks Maxime Ripard
@ 2016-06-29 19:05 ` Maxime Ripard
13 siblings, 0 replies; 22+ messages in thread
From: Maxime Ripard @ 2016-06-29 19:05 UTC (permalink / raw)
To: Mike Turquette, Stephen Boyd, Chen-Yu Tsai
Cc: linux-clk, Hans de Goede, Boris Brezillon, Rob Herring,
Vishnu Patekar, linux-arm-kernel, linux-kernel, devicetree,
Jean-Francois Moine, Maxime Ripard
Now that we have a different clock representation, switch to it.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
---
arch/arm/boot/dts/sun8i-h3.dtsi | 312 ++++++++--------------------------------
1 file changed, 60 insertions(+), 252 deletions(-)
diff --git a/arch/arm/boot/dts/sun8i-h3.dtsi b/arch/arm/boot/dts/sun8i-h3.dtsi
index 3c37f7e2b079..fdf9fdbda267 100644
--- a/arch/arm/boot/dts/sun8i-h3.dtsi
+++ b/arch/arm/boot/dts/sun8i-h3.dtsi
@@ -42,8 +42,10 @@
#include "skeleton.dtsi"
+#include <dt-bindings/clock/sun8i-h3-ccu.h>
#include <dt-bindings/interrupt-controller/arm-gic.h>
#include <dt-bindings/pinctrl/sun4i-a10.h>
+#include <dt-bindings/reset/sun8i-h3-ccu.h>
/ {
interrupt-parent = <&gic>;
@@ -104,191 +106,6 @@
clock-output-names = "osc32k";
};
- pll1: clk@01c20000 {
- #clock-cells = <0>;
- compatible = "allwinner,sun8i-a23-pll1-clk";
- reg = <0x01c20000 0x4>;
- clocks = <&osc24M>;
- clock-output-names = "pll1";
- };
-
- /* dummy clock until actually implemented */
- pll5: pll5_clk {
- #clock-cells = <0>;
- compatible = "fixed-clock";
- clock-frequency = <0>;
- clock-output-names = "pll5";
- };
-
- pll6: clk@01c20028 {
- #clock-cells = <1>;
- compatible = "allwinner,sun6i-a31-pll6-clk";
- reg = <0x01c20028 0x4>;
- clocks = <&osc24M>;
- clock-output-names = "pll6", "pll6x2";
- };
-
- pll6d2: pll6d2_clk {
- #clock-cells = <0>;
- compatible = "fixed-factor-clock";
- clock-div = <2>;
- clock-mult = <1>;
- clocks = <&pll6 0>;
- clock-output-names = "pll6d2";
- };
-
- /* dummy clock until pll6 can be reused */
- pll8: pll8_clk {
- #clock-cells = <0>;
- compatible = "fixed-clock";
- clock-frequency = <1>;
- clock-output-names = "pll8";
- };
-
- cpu: cpu_clk@01c20050 {
- #clock-cells = <0>;
- compatible = "allwinner,sun4i-a10-cpu-clk";
- reg = <0x01c20050 0x4>;
- clocks = <&osc32k>, <&osc24M>, <&pll1>, <&pll1>;
- clock-output-names = "cpu";
- };
-
- axi: axi_clk@01c20050 {
- #clock-cells = <0>;
- compatible = "allwinner,sun4i-a10-axi-clk";
- reg = <0x01c20050 0x4>;
- clocks = <&cpu>;
- clock-output-names = "axi";
- };
-
- ahb1: ahb1_clk@01c20054 {
- #clock-cells = <0>;
- compatible = "allwinner,sun6i-a31-ahb1-clk";
- reg = <0x01c20054 0x4>;
- clocks = <&osc32k>, <&osc24M>, <&axi>, <&pll6 0>;
- clock-output-names = "ahb1";
- };
-
- ahb2: ahb2_clk@01c2005c {
- #clock-cells = <0>;
- compatible = "allwinner,sun8i-h3-ahb2-clk";
- reg = <0x01c2005c 0x4>;
- clocks = <&ahb1>, <&pll6d2>;
- clock-output-names = "ahb2";
- };
-
- apb1: apb1_clk@01c20054 {
- #clock-cells = <0>;
- compatible = "allwinner,sun4i-a10-apb0-clk";
- reg = <0x01c20054 0x4>;
- clocks = <&ahb1>;
- clock-output-names = "apb1";
- };
-
- apb2: apb2_clk@01c20058 {
- #clock-cells = <0>;
- compatible = "allwinner,sun4i-a10-apb1-clk";
- reg = <0x01c20058 0x4>;
- clocks = <&osc32k>, <&osc24M>, <&pll6 0>, <&pll6 0>;
- clock-output-names = "apb2";
- };
-
- bus_gates: clk@01c20060 {
- #clock-cells = <1>;
- compatible = "allwinner,sun8i-h3-bus-gates-clk";
- reg = <0x01c20060 0x14>;
- clocks = <&ahb1>, <&ahb2>, <&apb1>, <&apb2>;
- clock-names = "ahb1", "ahb2", "apb1", "apb2";
- clock-indices = <5>, <6>, <8>,
- <9>, <10>, <13>,
- <14>, <17>, <18>,
- <19>, <20>,
- <21>, <23>,
- <24>, <25>,
- <26>, <27>,
- <28>, <29>,
- <30>, <31>, <32>,
- <35>, <36>, <37>,
- <40>, <41>, <43>,
- <44>, <52>, <53>,
- <54>, <64>,
- <65>, <69>, <72>,
- <76>, <77>, <78>,
- <96>, <97>, <98>,
- <112>, <113>,
- <114>, <115>,
- <116>, <128>, <135>;
- clock-output-names = "bus_ce", "bus_dma", "bus_mmc0",
- "bus_mmc1", "bus_mmc2", "bus_nand",
- "bus_sdram", "bus_gmac", "bus_ts",
- "bus_hstimer", "bus_spi0",
- "bus_spi1", "bus_otg",
- "bus_otg_ehci0", "bus_ehci1",
- "bus_ehci2", "bus_ehci3",
- "bus_otg_ohci0", "bus_ohci1",
- "bus_ohci2", "bus_ohci3", "bus_ve",
- "bus_lcd0", "bus_lcd1", "bus_deint",
- "bus_csi", "bus_tve", "bus_hdmi",
- "bus_de", "bus_gpu", "bus_msgbox",
- "bus_spinlock", "bus_codec",
- "bus_spdif", "bus_pio", "bus_ths",
- "bus_i2s0", "bus_i2s1", "bus_i2s2",
- "bus_i2c0", "bus_i2c1", "bus_i2c2",
- "bus_uart0", "bus_uart1",
- "bus_uart2", "bus_uart3",
- "bus_scr", "bus_ephy", "bus_dbg";
- };
-
- mmc0_clk: clk@01c20088 {
- #clock-cells = <1>;
- compatible = "allwinner,sun4i-a10-mmc-clk";
- reg = <0x01c20088 0x4>;
- clocks = <&osc24M>, <&pll6 0>, <&pll8>;
- clock-output-names = "mmc0",
- "mmc0_output",
- "mmc0_sample";
- };
-
- mmc1_clk: clk@01c2008c {
- #clock-cells = <1>;
- compatible = "allwinner,sun4i-a10-mmc-clk";
- reg = <0x01c2008c 0x4>;
- clocks = <&osc24M>, <&pll6 0>, <&pll8>;
- clock-output-names = "mmc1",
- "mmc1_output",
- "mmc1_sample";
- };
-
- mmc2_clk: clk@01c20090 {
- #clock-cells = <1>;
- compatible = "allwinner,sun4i-a10-mmc-clk";
- reg = <0x01c20090 0x4>;
- clocks = <&osc24M>, <&pll6 0>, <&pll8>;
- clock-output-names = "mmc2",
- "mmc2_output",
- "mmc2_sample";
- };
-
- usb_clk: clk@01c200cc {
- #clock-cells = <1>;
- #reset-cells = <1>;
- compatible = "allwinner,sun8i-h3-usb-clk";
- reg = <0x01c200cc 0x4>;
- clocks = <&osc24M>;
- clock-output-names = "usb_phy0", "usb_phy1",
- "usb_phy2", "usb_phy3",
- "usb_ohci0", "usb_ohci1",
- "usb_ohci2", "usb_ohci3";
- };
-
- mbus_clk: clk@01c2015c {
- #clock-cells = <0>;
- compatible = "allwinner,sun8i-a23-mbus-clk";
- reg = <0x01c2015c 0x4>;
- clocks = <&osc24M>, <&pll6 1>, <&pll5>;
- clock-output-names = "mbus";
- };
-
apb0: apb0_clk {
compatible = "fixed-factor-clock";
#clock-cells = <0>;
@@ -327,23 +144,23 @@
compatible = "allwinner,sun8i-h3-dma";
reg = <0x01c02000 0x1000>;
interrupts = <GIC_SPI 50 IRQ_TYPE_LEVEL_HIGH>;
- clocks = <&bus_gates 6>;
- resets = <&ahb_rst 6>;
+ clocks = <&ccu CLK_BUS_DMA>;
+ resets = <&ccu RST_BUS_DMA>;
#dma-cells = <1>;
};
mmc0: mmc@01c0f000 {
compatible = "allwinner,sun5i-a13-mmc";
reg = <0x01c0f000 0x1000>;
- clocks = <&bus_gates 8>,
- <&mmc0_clk 0>,
- <&mmc0_clk 1>,
- <&mmc0_clk 2>;
+ clocks = <&ccu CLK_BUS_MMC0>,
+ <&ccu CLK_MMC0>,
+ <&ccu CLK_MMC0_OUTPUT>,
+ <&ccu CLK_MMC0_SAMPLE>;
clock-names = "ahb",
"mmc",
"output",
"sample";
- resets = <&ahb_rst 8>;
+ resets = <&ccu RST_BUS_MMC0>;
reset-names = "ahb";
interrupts = <GIC_SPI 60 IRQ_TYPE_LEVEL_HIGH>;
status = "disabled";
@@ -354,15 +171,15 @@
mmc1: mmc@01c10000 {
compatible = "allwinner,sun5i-a13-mmc";
reg = <0x01c10000 0x1000>;
- clocks = <&bus_gates 9>,
- <&mmc1_clk 0>,
- <&mmc1_clk 1>,
- <&mmc1_clk 2>;
+ clocks = <&ccu CLK_BUS_MMC1>,
+ <&ccu CLK_MMC1>,
+ <&ccu CLK_MMC1_OUTPUT>,
+ <&ccu CLK_MMC1_SAMPLE>;
clock-names = "ahb",
"mmc",
"output",
"sample";
- resets = <&ahb_rst 9>;
+ resets = <&ccu RST_BUS_MMC1>;
reset-names = "ahb";
interrupts = <GIC_SPI 61 IRQ_TYPE_LEVEL_HIGH>;
status = "disabled";
@@ -373,15 +190,15 @@
mmc2: mmc@01c11000 {
compatible = "allwinner,sun5i-a13-mmc";
reg = <0x01c11000 0x1000>;
- clocks = <&bus_gates 10>,
- <&mmc2_clk 0>,
- <&mmc2_clk 1>,
- <&mmc2_clk 2>;
+ clocks = <&ccu CLK_BUS_MMC2>,
+ <&ccu CLK_MMC2>,
+ <&ccu CLK_MMC2_OUTPUT>,
+ <&ccu CLK_MMC2_SAMPLE>;
clock-names = "ahb",
"mmc",
"output",
"sample";
- resets = <&ahb_rst 10>;
+ resets = <&ccu RST_BUS_MMC2>;
reset-names = "ahb";
interrupts = <GIC_SPI 62 IRQ_TYPE_LEVEL_HIGH>;
status = "disabled";
@@ -401,18 +218,18 @@
"pmu1",
"pmu2",
"pmu3";
- clocks = <&usb_clk 8>,
- <&usb_clk 9>,
- <&usb_clk 10>,
- <&usb_clk 11>;
+ clocks = <&ccu CLK_USB_PHY0>,
+ <&ccu CLK_USB_PHY1>,
+ <&ccu CLK_USB_PHY2>,
+ <&ccu CLK_USB_PHY3>;
clock-names = "usb0_phy",
"usb1_phy",
"usb2_phy",
"usb3_phy";
- resets = <&usb_clk 0>,
- <&usb_clk 1>,
- <&usb_clk 2>,
- <&usb_clk 3>;
+ resets = <&ccu RST_USB_PHY0>,
+ <&ccu RST_USB_PHY1>,
+ <&ccu RST_USB_PHY2>,
+ <&ccu RST_USB_PHY3>;
reset-names = "usb0_reset",
"usb1_reset",
"usb2_reset",
@@ -425,8 +242,8 @@
compatible = "allwinner,sun8i-h3-ehci", "generic-ehci";
reg = <0x01c1b000 0x100>;
interrupts = <GIC_SPI 74 IRQ_TYPE_LEVEL_HIGH>;
- clocks = <&bus_gates 25>, <&bus_gates 29>;
- resets = <&ahb_rst 25>, <&ahb_rst 29>;
+ clocks = <&ccu CLK_BUS_EHCI1>, <&ccu CLK_BUS_OHCI1>;
+ resets = <&ccu RST_BUS_EHCI1>, <&ccu RST_BUS_OHCI1>;
phys = <&usbphy 1>;
phy-names = "usb";
status = "disabled";
@@ -436,9 +253,9 @@
compatible = "allwinner,sun8i-h3-ohci", "generic-ohci";
reg = <0x01c1b400 0x100>;
interrupts = <GIC_SPI 75 IRQ_TYPE_LEVEL_HIGH>;
- clocks = <&bus_gates 29>, <&bus_gates 25>,
- <&usb_clk 17>;
- resets = <&ahb_rst 29>, <&ahb_rst 25>;
+ clocks = <&ccu CLK_BUS_EHCI1>, <&ccu CLK_BUS_OHCI1>,
+ <&ccu CLK_USB_OHCI1>;
+ resets = <&ccu RST_BUS_EHCI1>, <&ccu RST_BUS_OHCI1>;
phys = <&usbphy 1>;
phy-names = "usb";
status = "disabled";
@@ -448,8 +265,8 @@
compatible = "allwinner,sun8i-h3-ehci", "generic-ehci";
reg = <0x01c1c000 0x100>;
interrupts = <GIC_SPI 76 IRQ_TYPE_LEVEL_HIGH>;
- clocks = <&bus_gates 26>, <&bus_gates 30>;
- resets = <&ahb_rst 26>, <&ahb_rst 30>;
+ clocks = <&ccu CLK_BUS_EHCI2>, <&ccu CLK_BUS_OHCI2>;
+ resets = <&ccu RST_BUS_EHCI2>, <&ccu RST_BUS_OHCI2>;
phys = <&usbphy 2>;
phy-names = "usb";
status = "disabled";
@@ -459,9 +276,9 @@
compatible = "allwinner,sun8i-h3-ohci", "generic-ohci";
reg = <0x01c1c400 0x100>;
interrupts = <GIC_SPI 77 IRQ_TYPE_LEVEL_HIGH>;
- clocks = <&bus_gates 30>, <&bus_gates 26>,
- <&usb_clk 18>;
- resets = <&ahb_rst 30>, <&ahb_rst 26>;
+ clocks = <&ccu CLK_BUS_EHCI2>, <&ccu CLK_BUS_OHCI2>,
+ <&ccu CLK_USB_OHCI2>;
+ resets = <&ccu RST_BUS_EHCI2>, <&ccu RST_BUS_OHCI2>;
phys = <&usbphy 2>;
phy-names = "usb";
status = "disabled";
@@ -471,8 +288,8 @@
compatible = "allwinner,sun8i-h3-ehci", "generic-ehci";
reg = <0x01c1d000 0x100>;
interrupts = <GIC_SPI 78 IRQ_TYPE_LEVEL_HIGH>;
- clocks = <&bus_gates 27>, <&bus_gates 31>;
- resets = <&ahb_rst 27>, <&ahb_rst 31>;
+ clocks = <&ccu CLK_BUS_EHCI3>, <&ccu CLK_BUS_OHCI3>;
+ resets = <&ccu RST_BUS_EHCI3>, <&ccu RST_BUS_OHCI3>;
phys = <&usbphy 3>;
phy-names = "usb";
status = "disabled";
@@ -482,20 +299,29 @@
compatible = "allwinner,sun8i-h3-ohci", "generic-ohci";
reg = <0x01c1d400 0x100>;
interrupts = <GIC_SPI 79 IRQ_TYPE_LEVEL_HIGH>;
- clocks = <&bus_gates 31>, <&bus_gates 27>,
- <&usb_clk 19>;
- resets = <&ahb_rst 31>, <&ahb_rst 27>;
+ clocks = <&ccu CLK_BUS_EHCI3>, <&ccu CLK_BUS_OHCI3>,
+ <&ccu CLK_USB_OHCI3>;
+ resets = <&ccu RST_BUS_EHCI3>, <&ccu RST_BUS_OHCI3>;
phys = <&usbphy 3>;
phy-names = "usb";
status = "disabled";
};
+ ccu: clock@01c20000 {
+ compatible = "allwinner,sun8i-h3-ccu";
+ reg = <0x01c20000 0x400>;
+ clocks = <&osc24M>, <&osc32k>;
+ clock-names = "hosc", "losc";
+ #clock-cells = <1>;
+ #reset-cells = <1>;
+ };
+
pio: pinctrl@01c20800 {
compatible = "allwinner,sun8i-h3-pinctrl";
reg = <0x01c20800 0x400>;
interrupts = <GIC_SPI 11 IRQ_TYPE_LEVEL_HIGH>,
<GIC_SPI 17 IRQ_TYPE_LEVEL_HIGH>;
- clocks = <&bus_gates 69>;
+ clocks = <&ccu CLK_BUS_PIO>;
gpio-controller;
#gpio-cells = <3>;
interrupt-controller;
@@ -549,24 +375,6 @@
};
};
- ahb_rst: reset@01c202c0 {
- #reset-cells = <1>;
- compatible = "allwinner,sun6i-a31-ahb1-reset";
- reg = <0x01c202c0 0xc>;
- };
-
- apb1_rst: reset@01c202d0 {
- #reset-cells = <1>;
- compatible = "allwinner,sun6i-a31-clock-reset";
- reg = <0x01c202d0 0x4>;
- };
-
- apb2_rst: reset@01c202d8 {
- #reset-cells = <1>;
- compatible = "allwinner,sun6i-a31-clock-reset";
- reg = <0x01c202d8 0x4>;
- };
-
timer@01c20c00 {
compatible = "allwinner,sun4i-a10-timer";
reg = <0x01c20c00 0xa0>;
@@ -587,8 +395,8 @@
interrupts = <GIC_SPI 0 IRQ_TYPE_LEVEL_HIGH>;
reg-shift = <2>;
reg-io-width = <4>;
- clocks = <&bus_gates 112>;
- resets = <&apb2_rst 16>;
+ clocks = <&ccu CLK_BUS_UART0>;
+ resets = <&ccu RST_BUS_UART0>;
dmas = <&dma 6>, <&dma 6>;
dma-names = "rx", "tx";
status = "disabled";
@@ -600,8 +408,8 @@
interrupts = <GIC_SPI 1 IRQ_TYPE_LEVEL_HIGH>;
reg-shift = <2>;
reg-io-width = <4>;
- clocks = <&bus_gates 113>;
- resets = <&apb2_rst 17>;
+ clocks = <&ccu CLK_BUS_UART1>;
+ resets = <&ccu RST_BUS_UART1>;
dmas = <&dma 7>, <&dma 7>;
dma-names = "rx", "tx";
status = "disabled";
@@ -613,8 +421,8 @@
interrupts = <GIC_SPI 2 IRQ_TYPE_LEVEL_HIGH>;
reg-shift = <2>;
reg-io-width = <4>;
- clocks = <&bus_gates 114>;
- resets = <&apb2_rst 18>;
+ clocks = <&ccu CLK_BUS_UART2>;
+ resets = <&ccu RST_BUS_UART2>;
dmas = <&dma 8>, <&dma 8>;
dma-names = "rx", "tx";
status = "disabled";
@@ -626,8 +434,8 @@
interrupts = <GIC_SPI 3 IRQ_TYPE_LEVEL_HIGH>;
reg-shift = <2>;
reg-io-width = <4>;
- clocks = <&bus_gates 115>;
- resets = <&apb2_rst 19>;
+ clocks = <&ccu CLK_BUS_UART3>;
+ resets = <&ccu RST_BUS_UART3>;
dmas = <&dma 9>, <&dma 9>;
dma-names = "rx", "tx";
status = "disabled";
--
2.9.0
^ permalink raw reply related [flat|nested] 22+ messages in thread