Linux-Clk Archive on lore.kernel.org
 help / color / Atom feed
From: Samuel Holland <samuel@sholland.org>
To: Maxime Ripard <maxime.ripard@bootlin.com>,
	Chen-Yu Tsai <wens@csie.org>,
	Jassi Brar <jassisinghbrar@gmail.com>,
	Michael Turquette <mturquette@baylibre.com>,
	Stephen Boyd <sboyd@kernel.org>, Rob Herring <robh+dt@kernel.org>,
	Mark Rutland <mark.rutland@arm.com>,
	Corentin Labbe <clabbe.montjoie@gmail.com>,
	Vasily Khoruzhick <anarsoul@gmail.com>
Cc: devicetree@vger.kernel.org, linux-arm-kernel@lists.infradead.org,
	linux-clk@vger.kernel.org, linux-kernel@vger.kernel.org,
	linux-sunxi@googlegroups.com,
	Samuel Holland <samuel@sholland.org>
Subject: [PATCH v4 04/10] mailbox: sunxi-msgbox: Add a new mailbox driver
Date: Mon, 19 Aug 2019 22:23:05 -0500
Message-ID: <20190820032311.6506-5-samuel@sholland.org> (raw)
In-Reply-To: <20190820032311.6506-1-samuel@sholland.org>

Allwinner sun8i, sun9i, and sun50i SoCs contain a hardware message box
used for communication between the ARM CPUs and the ARISC management
coprocessor. The hardware contains 8 unidirectional 4-message FIFOs.

Add a driver for it, so it can be used for SCPI or other communication
protocols.

Signed-off-by: Samuel Holland <samuel@sholland.org>
---
 drivers/mailbox/Kconfig        |  10 +
 drivers/mailbox/Makefile       |   2 +
 drivers/mailbox/sunxi-msgbox.c | 323 +++++++++++++++++++++++++++++++++
 3 files changed, 335 insertions(+)
 create mode 100644 drivers/mailbox/sunxi-msgbox.c

diff --git a/drivers/mailbox/Kconfig b/drivers/mailbox/Kconfig
index ab4eb750bbdd..57d12936175e 100644
--- a/drivers/mailbox/Kconfig
+++ b/drivers/mailbox/Kconfig
@@ -227,4 +227,14 @@ config ZYNQMP_IPI_MBOX
 	  message to the IPI buffer and will access the IPI control
 	  registers to kick the other processor or enquire status.
 
+config SUNXI_MSGBOX
+	tristate "Allwinner sunxi Message Box"
+	depends on ARCH_SUNXI || COMPILE_TEST
+	default ARCH_SUNXI
+	help
+	  Mailbox implementation for the hardware message box present in
+	  Allwinner sun8i, sun9i, and sun50i SoCs. The hardware message box is
+	  used for communication between the application CPUs and the power
+	  management coprocessor.
+
 endif
diff --git a/drivers/mailbox/Makefile b/drivers/mailbox/Makefile
index c22fad6f696b..bec2d50b0976 100644
--- a/drivers/mailbox/Makefile
+++ b/drivers/mailbox/Makefile
@@ -48,3 +48,5 @@ obj-$(CONFIG_STM32_IPCC) 	+= stm32-ipcc.o
 obj-$(CONFIG_MTK_CMDQ_MBOX)	+= mtk-cmdq-mailbox.o
 
 obj-$(CONFIG_ZYNQMP_IPI_MBOX)	+= zynqmp-ipi-mailbox.o
+
+obj-$(CONFIG_SUNXI_MSGBOX)	+= sunxi-msgbox.o
diff --git a/drivers/mailbox/sunxi-msgbox.c b/drivers/mailbox/sunxi-msgbox.c
new file mode 100644
index 000000000000..29a5101a5390
--- /dev/null
+++ b/drivers/mailbox/sunxi-msgbox.c
@@ -0,0 +1,323 @@
+// SPDX-License-Identifier: GPL-2.0
+//
+// Copyright (c) 2017-2019 Samuel Holland <samuel@sholland.org>
+
+#include <linux/bitops.h>
+#include <linux/clk.h>
+#include <linux/device.h>
+#include <linux/err.h>
+#include <linux/interrupt.h>
+#include <linux/io.h>
+#include <linux/kernel.h>
+#include <linux/mailbox_controller.h>
+#include <linux/module.h>
+#include <linux/of.h>
+#include <linux/of_irq.h>
+#include <linux/platform_device.h>
+#include <linux/reset.h>
+#include <linux/spinlock.h>
+
+#define NUM_CHANS		8
+
+#define CTRL_REG(n)		(0x0000 + 0x4 * ((n) / 4))
+#define CTRL_RX(n)		BIT(0 + 8 * ((n) % 4))
+#define CTRL_TX(n)		BIT(4 + 8 * ((n) % 4))
+
+#define REMOTE_IRQ_EN_REG	0x0040
+#define REMOTE_IRQ_STAT_REG	0x0050
+#define LOCAL_IRQ_EN_REG	0x0060
+#define LOCAL_IRQ_STAT_REG	0x0070
+
+#define RX_IRQ(n)		BIT(0 + 2 * (n))
+#define RX_IRQ_MASK		0x5555
+#define TX_IRQ(n)		BIT(1 + 2 * (n))
+#define TX_IRQ_MASK		0xaaaa
+
+#define FIFO_STAT_REG(n)	(0x0100 + 0x4 * (n))
+#define FIFO_STAT_MASK		GENMASK(0, 0)
+
+#define MSG_STAT_REG(n)		(0x0140 + 0x4 * (n))
+#define MSG_STAT_MASK		GENMASK(2, 0)
+
+#define MSG_DATA_REG(n)		(0x0180 + 0x4 * (n))
+
+#define mbox_dbg(mbox, ...)	dev_dbg((mbox)->controller.dev, __VA_ARGS__)
+
+struct sunxi_msgbox {
+	struct mbox_controller controller;
+	struct clk *clk;
+	spinlock_t lock;
+	void __iomem *regs;
+};
+
+static bool sunxi_msgbox_last_tx_done(struct mbox_chan *chan);
+static bool sunxi_msgbox_peek_data(struct mbox_chan *chan);
+
+static inline int channel_number(struct mbox_chan *chan)
+{
+	return chan - chan->mbox->chans;
+}
+
+static inline struct sunxi_msgbox *channel_to_msgbox(struct mbox_chan *chan)
+{
+	return chan->con_priv;
+}
+
+static irqreturn_t sunxi_msgbox_irq(int irq, void *dev_id)
+{
+	struct sunxi_msgbox *mbox = dev_id;
+	uint32_t status;
+	int n;
+
+	/* Only examine channels that are currently enabled. */
+	status = readl(mbox->regs + LOCAL_IRQ_EN_REG) &
+		 readl(mbox->regs + LOCAL_IRQ_STAT_REG);
+
+	if (!(status & RX_IRQ_MASK))
+		return IRQ_NONE;
+
+	for (n = 0; n < NUM_CHANS; ++n) {
+		struct mbox_chan *chan = &mbox->controller.chans[n];
+
+		if (!(status & RX_IRQ(n)))
+			continue;
+
+		while (sunxi_msgbox_peek_data(chan)) {
+			uint32_t msg = readl(mbox->regs + MSG_DATA_REG(n));
+
+			mbox_dbg(mbox, "Channel %d received 0x%08x\n", n, msg);
+			mbox_chan_received_data(chan, &msg);
+		}
+
+		/* The IRQ can be cleared only once the FIFO is empty. */
+		writel(RX_IRQ(n), mbox->regs + LOCAL_IRQ_STAT_REG);
+	}
+
+	return IRQ_HANDLED;
+}
+
+static int sunxi_msgbox_send_data(struct mbox_chan *chan, void *data)
+{
+	struct sunxi_msgbox *mbox = channel_to_msgbox(chan);
+	int n = channel_number(chan);
+	uint32_t msg = *(uint32_t *)data;
+
+	/* Using a channel backwards gets the hardware into a bad state. */
+	if (WARN_ON_ONCE(!(readl(mbox->regs + CTRL_REG(n)) & CTRL_TX(n))))
+		return 0;
+
+	/* We cannot post a new message if the FIFO is full. */
+	if (readl(mbox->regs + FIFO_STAT_REG(n)) & FIFO_STAT_MASK) {
+		mbox_dbg(mbox, "Channel %d busy sending 0x%08x\n", n, msg);
+		return -EBUSY;
+	}
+
+	writel(msg, mbox->regs + MSG_DATA_REG(n));
+	mbox_dbg(mbox, "Channel %d sent 0x%08x\n", n, msg);
+
+	return 0;
+}
+
+static int sunxi_msgbox_startup(struct mbox_chan *chan)
+{
+	struct sunxi_msgbox *mbox = channel_to_msgbox(chan);
+	int n = channel_number(chan);
+
+	/* The coprocessor is responsible for setting channel directions. */
+	if (readl(mbox->regs + CTRL_REG(n)) & CTRL_RX(n)) {
+		/* Flush the receive FIFO. */
+		while (sunxi_msgbox_peek_data(chan))
+			readl(mbox->regs + MSG_DATA_REG(n));
+		writel(RX_IRQ(n), mbox->regs + LOCAL_IRQ_STAT_REG);
+
+		/* Enable the receive IRQ. */
+		spin_lock(&mbox->lock);
+		writel(readl(mbox->regs + LOCAL_IRQ_EN_REG) | RX_IRQ(n),
+		       mbox->regs + LOCAL_IRQ_EN_REG);
+		spin_unlock(&mbox->lock);
+	}
+
+	mbox_dbg(mbox, "Channel %d startup complete\n", n);
+
+	return 0;
+}
+
+static void sunxi_msgbox_shutdown(struct mbox_chan *chan)
+{
+	struct sunxi_msgbox *mbox = channel_to_msgbox(chan);
+	int n = channel_number(chan);
+
+	if (readl(mbox->regs + CTRL_REG(n)) & CTRL_RX(n)) {
+		/* Disable the receive IRQ. */
+		spin_lock(&mbox->lock);
+		writel(readl(mbox->regs + LOCAL_IRQ_EN_REG) & ~RX_IRQ(n),
+		       mbox->regs + LOCAL_IRQ_EN_REG);
+		spin_unlock(&mbox->lock);
+
+		/* Attempt to flush the FIFO until the IRQ is cleared. */
+		do {
+			while (sunxi_msgbox_peek_data(chan))
+				readl(mbox->regs + MSG_DATA_REG(n));
+			writel(RX_IRQ(n), mbox->regs + LOCAL_IRQ_STAT_REG);
+		} while (readl(mbox->regs + LOCAL_IRQ_STAT_REG) & RX_IRQ(n));
+	}
+
+	mbox_dbg(mbox, "Channel %d shutdown complete\n", n);
+}
+
+static bool sunxi_msgbox_last_tx_done(struct mbox_chan *chan)
+{
+	struct sunxi_msgbox *mbox = channel_to_msgbox(chan);
+	int n = channel_number(chan);
+
+	/*
+	 * The hardware allows snooping on the remote user's IRQ statuses.
+	 * We consider a message to be acknowledged only once the receive IRQ
+	 * for that channel is cleared. Since the receive IRQ for a channel
+	 * cannot be cleared until the FIFO for that channel is empty, this
+	 * ensures that the message has actually been read. It also gives the
+	 * recipient an opportunity to perform minimal processing before
+	 * acknowledging the message.
+	 */
+	return !(readl(mbox->regs + REMOTE_IRQ_STAT_REG) & RX_IRQ(n));
+}
+
+static bool sunxi_msgbox_peek_data(struct mbox_chan *chan)
+{
+	struct sunxi_msgbox *mbox = channel_to_msgbox(chan);
+	int n = channel_number(chan);
+
+	return readl(mbox->regs + MSG_STAT_REG(n)) & MSG_STAT_MASK;
+}
+
+static const struct mbox_chan_ops sunxi_msgbox_chan_ops = {
+	.send_data    = sunxi_msgbox_send_data,
+	.startup      = sunxi_msgbox_startup,
+	.shutdown     = sunxi_msgbox_shutdown,
+	.last_tx_done = sunxi_msgbox_last_tx_done,
+	.peek_data    = sunxi_msgbox_peek_data,
+};
+
+static int sunxi_msgbox_probe(struct platform_device *pdev)
+{
+	struct device *dev = &pdev->dev;
+	struct mbox_chan *chans;
+	struct reset_control *reset;
+	struct resource *res;
+	struct sunxi_msgbox *mbox;
+	int i, ret;
+
+	mbox = devm_kzalloc(dev, sizeof(*mbox), GFP_KERNEL);
+	if (!mbox)
+		return -ENOMEM;
+
+	chans = devm_kcalloc(dev, NUM_CHANS, sizeof(*chans), GFP_KERNEL);
+	if (!chans)
+		return -ENOMEM;
+
+	for (i = 0; i < NUM_CHANS; ++i)
+		chans[i].con_priv = mbox;
+
+	mbox->clk = devm_clk_get(dev, NULL);
+	if (IS_ERR(mbox->clk)) {
+		ret = PTR_ERR(mbox->clk);
+		dev_err(dev, "Failed to get clock: %d\n", ret);
+		return ret;
+	}
+
+	ret = clk_prepare_enable(mbox->clk);
+	if (ret) {
+		dev_err(dev, "Failed to enable clock: %d\n", ret);
+		return ret;
+	}
+
+	reset = devm_reset_control_get(dev, NULL);
+	if (IS_ERR(reset)) {
+		ret = PTR_ERR(reset);
+		dev_err(dev, "Failed to get reset control: %d\n", ret);
+		goto err_disable_unprepare;
+	}
+
+	ret = reset_control_deassert(reset);
+	if (ret) {
+		dev_err(dev, "Failed to deassert reset: %d\n", ret);
+		goto err_disable_unprepare;
+	}
+
+	res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+	if (!res) {
+		ret = -ENODEV;
+		goto err_disable_unprepare;
+	}
+
+	mbox->regs = devm_ioremap_resource(&pdev->dev, res);
+	if (IS_ERR(mbox->regs)) {
+		ret = PTR_ERR(mbox->regs);
+		dev_err(dev, "Failed to map MMIO resource: %d\n", ret);
+		goto err_disable_unprepare;
+	}
+
+	/* Disable all IRQs for this end of the msgbox. */
+	writel(0, mbox->regs + LOCAL_IRQ_EN_REG);
+
+	ret = devm_request_irq(dev, irq_of_parse_and_map(dev->of_node, 0),
+			       sunxi_msgbox_irq, 0, dev_name(dev), mbox);
+	if (ret) {
+		dev_err(dev, "Failed to register IRQ handler: %d\n", ret);
+		goto err_disable_unprepare;
+	}
+
+	mbox->controller.dev           = dev;
+	mbox->controller.ops           = &sunxi_msgbox_chan_ops;
+	mbox->controller.chans         = chans;
+	mbox->controller.num_chans     = NUM_CHANS;
+	mbox->controller.txdone_irq    = false;
+	mbox->controller.txdone_poll   = true;
+	mbox->controller.txpoll_period = 5;
+
+	spin_lock_init(&mbox->lock);
+	platform_set_drvdata(pdev, mbox);
+
+	ret = mbox_controller_register(&mbox->controller);
+	if (ret) {
+		dev_err(dev, "Failed to register controller: %d\n", ret);
+		goto err_disable_unprepare;
+	}
+
+	return 0;
+
+err_disable_unprepare:
+	clk_disable_unprepare(mbox->clk);
+
+	return ret;
+}
+
+static int sunxi_msgbox_remove(struct platform_device *pdev)
+{
+	struct sunxi_msgbox *mbox = platform_get_drvdata(pdev);
+
+	mbox_controller_unregister(&mbox->controller);
+	clk_disable_unprepare(mbox->clk);
+
+	return 0;
+}
+
+static const struct of_device_id sunxi_msgbox_of_match[] = {
+	{ .compatible = "allwinner,sun6i-a31-msgbox", },
+	{},
+};
+MODULE_DEVICE_TABLE(of, sunxi_msgbox_of_match);
+
+static struct platform_driver sunxi_msgbox_driver = {
+	.driver = {
+		.name = "sunxi-msgbox",
+		.of_match_table = sunxi_msgbox_of_match,
+	},
+	.probe  = sunxi_msgbox_probe,
+	.remove = sunxi_msgbox_remove,
+};
+module_platform_driver(sunxi_msgbox_driver);
+
+MODULE_AUTHOR("Samuel Holland <samuel@sholland.org>");
+MODULE_DESCRIPTION("Allwinner sunxi Message Box");
+MODULE_LICENSE("GPL v2");
-- 
2.21.0


  parent reply index

Thread overview: 29+ messages / expand[flat|nested]  mbox.gz  Atom feed  top
2019-08-20  3:23 [PATCH v4 00/10] Allwinner sunxi message box support Samuel Holland
2019-08-20  3:23 ` [PATCH v4 01/10] clk: sunxi-ng: Mark msgbox clocks as critical Samuel Holland
2019-08-20  3:23 ` [PATCH v4 02/10] clk: sunxi-ng: Mark AR100 " Samuel Holland
2019-08-20  7:11   ` Maxime Ripard
2019-08-20 13:02     ` Samuel Holland
2019-08-21 12:24       ` Maxime Ripard
2019-09-05 18:56         ` Stephen Boyd
2019-08-20  3:23 ` [PATCH v4 03/10] dt-bindings: mailbox: Add a sunxi message box binding Samuel Holland
2019-08-20  7:14   ` Maxime Ripard
2019-08-20 13:04     ` Samuel Holland
2019-08-21 12:07       ` Maxime Ripard
2019-08-20  3:23 ` Samuel Holland [this message]
2019-08-20  8:27   ` [PATCH v4 04/10] mailbox: sunxi-msgbox: Add a new mailbox driver Maxime Ripard
2019-08-20 11:18   ` Ondřej Jirman
2019-08-20 13:07     ` Samuel Holland
2019-08-20 13:34       ` Ondřej Jirman
2019-08-21 12:30       ` Maxime Ripard
2019-08-20  3:23 ` [PATCH v4 05/10] ARM: dts: sunxi: a80: Add msgbox node Samuel Holland
2019-08-20  8:15   ` Maxime Ripard
2019-08-20 13:17     ` Samuel Holland
2019-08-23 14:56       ` Maxime Ripard
2019-08-20  3:23 ` [PATCH v4 06/10] ARM: dts: sunxi: a83t: " Samuel Holland
2019-08-20  3:23 ` [PATCH v4 07/10] ARM: dts: sunxi: h3/h5: " Samuel Holland
2019-08-20  3:23 ` [PATCH v4 08/10] arm64: dts: allwinner: a64: " Samuel Holland
2019-08-20  3:23 ` [PATCH v4 09/10] arm64: dts: allwinner: h6: " Samuel Holland
2019-08-20  3:23 ` [PATCH v4 10/10] [DO NOT MERGE] drivers: firmware: msgbox demo Samuel Holland
2019-09-09  3:22 ` [PATCH v4 00/10] Allwinner sunxi message box support Ondřej Jirman
2019-09-09  3:54   ` Samuel Holland
2019-09-09 12:36     ` Ondřej Jirman

Reply instructions:

You may reply publically to this message via plain-text email
using any one of the following methods:

* Save the following mbox file, import it into your mail client,
  and reply-to-all from there: mbox

  Avoid top-posting and favor interleaved quoting:
  https://en.wikipedia.org/wiki/Posting_style#Interleaved_style

* Reply using the --to, --cc, and --in-reply-to
  switches of git-send-email(1):

  git send-email \
    --in-reply-to=20190820032311.6506-5-samuel@sholland.org \
    --to=samuel@sholland.org \
    --cc=anarsoul@gmail.com \
    --cc=clabbe.montjoie@gmail.com \
    --cc=devicetree@vger.kernel.org \
    --cc=jassisinghbrar@gmail.com \
    --cc=linux-arm-kernel@lists.infradead.org \
    --cc=linux-clk@vger.kernel.org \
    --cc=linux-kernel@vger.kernel.org \
    --cc=linux-sunxi@googlegroups.com \
    --cc=mark.rutland@arm.com \
    --cc=maxime.ripard@bootlin.com \
    --cc=mturquette@baylibre.com \
    --cc=robh+dt@kernel.org \
    --cc=sboyd@kernel.org \
    --cc=wens@csie.org \
    /path/to/YOUR_REPLY

  https://kernel.org/pub/software/scm/git/docs/git-send-email.html

* If your mail client supports setting the In-Reply-To header
  via mailto: links, try the mailto: link

Linux-Clk Archive on lore.kernel.org

Archives are clonable:
	git clone --mirror https://lore.kernel.org/linux-clk/0 linux-clk/git/0.git

	# If you have public-inbox 1.1+ installed, you may
	# initialize and index your mirror using the following commands:
	public-inbox-init -V2 linux-clk linux-clk/ https://lore.kernel.org/linux-clk \
		linux-clk@vger.kernel.org linux-clk@archiver.kernel.org
	public-inbox-index linux-clk

Example config snippet for mirrors

Newsgroup available over NNTP:
	nntp://nntp.lore.kernel.org/org.kernel.vger.linux-clk


AGPL code for this site: git clone https://public-inbox.org/ public-inbox