[PATCH AUTOSEL 4.9 02/80] clk: sunxi: Fix incorrect usage of round_down()

[PATCH AUTOSEL 4.9 02/80] clk: sunxi: Fix incorrect usage of round_down()

[Sasha Levin]

From: Rikard Falkeborn <rikard.falkeborn@gmail.com>

[ Upstream commit ee25d9742dabed3fd18158b518f846abeb70f319 ]

round_down() can only round to powers of 2. If round_down() is asked
to round to something that is not a power of 2, incorrect results are
produced. The incorrect results can be both too large and too small.

Instead, use rounddown() which can round to any number.

Fixes: 6a721db180a2 ("clk: sunxi: Add A31 clocks support")
Signed-off-by: Rikard Falkeborn <rikard.falkeborn@gmail.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 drivers/clk/sunxi/clk-sunxi.c | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)

diff --git a/drivers/clk/sunxi/clk-sunxi.c b/drivers/clk/sunxi/clk-sunxi.c
index f2c9274b8bd5..369164f0bd0e 100644
--- a/drivers/clk/sunxi/clk-sunxi.c
+++ b/drivers/clk/sunxi/clk-sunxi.c
@@ -98,7 +98,7 @@ static void sun6i_a31_get_pll1_factors(struct factors_request *req)
 	 * Round down the frequency to the closest multiple of either
 	 * 6 or 16
 	 */
-	u32 round_freq_6 = round_down(freq_mhz, 6);
+	u32 round_freq_6 = rounddown(freq_mhz, 6);
 	u32 round_freq_16 = round_down(freq_mhz, 16);
 
 	if (round_freq_6 > round_freq_16)
-- 
2.25.1

[PATCH AUTOSEL 4.9 06/80] clk: qcom: msm8916: Fix the address location of pll->config_reg

[Sasha Levin]

From: Bryan O'Donoghue <bryan.odonoghue@linaro.org>

[ Upstream commit f47ab3c2f5338828a67e89d5f688d2cef9605245 ]

During the process of debugging a processor derived from the msm8916 which
we found the new processor was not starting one of its PLLs.

After tracing the addresses and writes that downstream was doing and
comparing to upstream it became obvious that we were writing to a different
register location than downstream when trying to configure the PLL.

This error is also present in upstream msm8916.

As an example clk-pll.c::clk_pll_recalc_rate wants to write to
pll->config_reg updating the bit-field POST_DIV_RATIO. That bit-field is
defined in PLL_USER_CTL not in PLL_CONFIG_CTL. Taking the BIMC PLL as an
example

lm80-p0436-13_c_qc_snapdragon_410_processor_hrd.pdf

0x01823010 GCC_BIMC_PLL_USER_CTL
0x01823014 GCC_BIMC_PLL_CONFIG_CTL

This pattern is repeated for gpll0, gpll1, gpll2 and bimc_pll.

This error is likely not apparent since the bootloader will already have
initialized these PLLs.

This patch corrects the location of config_reg from PLL_CONFIG_CTL to
PLL_USER_CTL for all relevant PLLs on msm8916.

Fixes commit 3966fab8b6ab ("clk: qcom: Add MSM8916 Global Clock Controller support")

Cc: Georgi Djakov <georgi.djakov@linaro.org>
Cc: Andy Gross <agross@kernel.org>
Cc: Bjorn Andersson <bjorn.andersson@linaro.org>
Cc: Michael Turquette <mturquette@baylibre.com>
Cc: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Link: https://lkml.kernel.org/r/20200329124116.4185447-1-bryan.odonoghue@linaro.org
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 drivers/clk/qcom/gcc-msm8916.c | 8 ++++----
 1 file changed, 4 insertions(+), 4 deletions(-)

diff --git a/drivers/clk/qcom/gcc-msm8916.c b/drivers/clk/qcom/gcc-msm8916.c
index 8dd71345b5d0..55430c8f1bc2 100644
--- a/drivers/clk/qcom/gcc-msm8916.c
+++ b/drivers/clk/qcom/gcc-msm8916.c
@@ -270,7 +270,7 @@ static struct clk_pll gpll0 = {
 	.l_reg = 0x21004,
 	.m_reg = 0x21008,
 	.n_reg = 0x2100c,
-	.config_reg = 0x21014,
+	.config_reg = 0x21010,
 	.mode_reg = 0x21000,
 	.status_reg = 0x2101c,
 	.status_bit = 17,
@@ -297,7 +297,7 @@ static struct clk_pll gpll1 = {
 	.l_reg = 0x20004,
 	.m_reg = 0x20008,
 	.n_reg = 0x2000c,
-	.config_reg = 0x20014,
+	.config_reg = 0x20010,
 	.mode_reg = 0x20000,
 	.status_reg = 0x2001c,
 	.status_bit = 17,
@@ -324,7 +324,7 @@ static struct clk_pll gpll2 = {
 	.l_reg = 0x4a004,
 	.m_reg = 0x4a008,
 	.n_reg = 0x4a00c,
-	.config_reg = 0x4a014,
+	.config_reg = 0x4a010,
 	.mode_reg = 0x4a000,
 	.status_reg = 0x4a01c,
 	.status_bit = 17,
@@ -351,7 +351,7 @@ static struct clk_pll bimc_pll = {
 	.l_reg = 0x23004,
 	.m_reg = 0x23008,
 	.n_reg = 0x2300c,
-	.config_reg = 0x23014,
+	.config_reg = 0x23010,
 	.mode_reg = 0x23000,
 	.status_reg = 0x2301c,
 	.status_bit = 17,
-- 
2.25.1

[PATCH AUTOSEL 4.9 20/80] clk: clk-flexgen: fix clock-critical handling

[Sasha Levin]

From: Alain Volmat <avolmat@me.com>

[ Upstream commit a403bbab1a73d798728d76931cab3ff0399b9560 ]

Fixes an issue leading to having all clocks following a critical
clocks marked as well as criticals.

Fixes: fa6415affe20 ("clk: st: clk-flexgen: Detect critical clocks")
Signed-off-by: Alain Volmat <avolmat@me.com>
Link: https://lkml.kernel.org/r/20200322140740.3970-1-avolmat@me.com
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 drivers/clk/st/clk-flexgen.c | 1 +
 1 file changed, 1 insertion(+)

diff --git a/drivers/clk/st/clk-flexgen.c b/drivers/clk/st/clk-flexgen.c
index a485f3b284b9..033e6062599d 100644
--- a/drivers/clk/st/clk-flexgen.c
+++ b/drivers/clk/st/clk-flexgen.c
@@ -371,6 +371,7 @@ static void __init st_of_flexgen_setup(struct device_node *np)
 			break;
 		}
 
+		flex_flags &= ~CLK_IS_CRITICAL;
 		of_clk_detect_critical(np, i, &flex_flags);
 
 		/*
-- 
2.25.1

[PATCH AUTOSEL 4.9 44/80] clk: ti: composite: fix memory leak

[Sasha Levin]

From: Tero Kristo <t-kristo@ti.com>

[ Upstream commit c7c1cbbc9217ebb5601b88d138d4a5358548de9d ]

The parent_names is never released for a component clock definition,
causing some memory leak. Fix by releasing it once it is no longer
needed.

Reported-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Link: https://lkml.kernel.org/r/20200429131341.4697-2-t-kristo@ti.com
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 drivers/clk/ti/composite.c | 1 +
 1 file changed, 1 insertion(+)

diff --git a/drivers/clk/ti/composite.c b/drivers/clk/ti/composite.c
index 1cf70f452e1e..3725b2e0c788 100644
--- a/drivers/clk/ti/composite.c
+++ b/drivers/clk/ti/composite.c
@@ -226,6 +226,7 @@ static void __init _register_composite(struct clk_hw *hw,
 		if (!cclk->comp_clks[i])
 			continue;
 		list_del(&cclk->comp_clks[i]->link);
+		kfree(cclk->comp_clks[i]->parent_names);
 		kfree(cclk->comp_clks[i]);
 	}
 
-- 
2.25.1

[PATCH AUTOSEL 4.9 54/80] clk: samsung: exynos5433: Add IGNORE_UNUSED flag to sclk_i2s1

[Sasha Levin]

From: Marek Szyprowski <m.szyprowski@samsung.com>

[ Upstream commit 25bdae0f1c6609ceaf55fe6700654f0be2253d8e ]

Mark the SCLK clock for Exynos5433 I2S1 device with IGNORE_UNUSED flag to
match its behaviour with SCLK clock for AUD_I2S (I2S0) device until
a proper fix for Exynos I2S driver is ready.

This fixes the following synchronous abort issue revealed by the probe
order change caused by the commit 93d2e4322aa7 ("of: platform: Batch
fwnode parsing when adding all top level devices")

Internal error: synchronous external abort: 96000210 [#1] PREEMPT SMP
Modules linked in:
CPU: 0 PID: 50 Comm: kworker/0:1 Not tainted 5.7.0-rc5+ #701
Hardware name: Samsung TM2E board (DT)
Workqueue: events deferred_probe_work_func
pstate: 60000005 (nZCv daif -PAN -UAO)
pc : samsung_i2s_probe+0x768/0x8f0
lr : samsung_i2s_probe+0x688/0x8f0
...
Call trace:
 samsung_i2s_probe+0x768/0x8f0
 platform_drv_probe+0x50/0xa8
 really_probe+0x108/0x370
 driver_probe_device+0x54/0xb8
 __device_attach_driver+0x90/0xc0
 bus_for_each_drv+0x70/0xc8
 __device_attach+0xdc/0x140
 device_initial_probe+0x10/0x18
 bus_probe_device+0x94/0xa0
 deferred_probe_work_func+0x70/0xa8
 process_one_work+0x2a8/0x718
 worker_thread+0x48/0x470
 kthread+0x134/0x160
 ret_from_fork+0x10/0x1c
Code: 17ffffaf d503201f f94086c0 91003000 (88dffc00)
---[ end trace ccf721c9400ddbd6 ]---

Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 drivers/clk/samsung/clk-exynos5433.c | 3 ++-
 1 file changed, 2 insertions(+), 1 deletion(-)

diff --git a/drivers/clk/samsung/clk-exynos5433.c b/drivers/clk/samsung/clk-exynos5433.c
index 09cdd35dc434..a082b026791a 100644
--- a/drivers/clk/samsung/clk-exynos5433.c
+++ b/drivers/clk/samsung/clk-exynos5433.c
@@ -1672,7 +1672,8 @@ static const struct samsung_gate_clock peric_gate_clks[] __initconst = {
 	GATE(CLK_SCLK_PCM1, "sclk_pcm1", "sclk_pcm1_peric",
 			ENABLE_SCLK_PERIC, 7, CLK_SET_RATE_PARENT, 0),
 	GATE(CLK_SCLK_I2S1, "sclk_i2s1", "sclk_i2s1_peric",
-			ENABLE_SCLK_PERIC, 6, CLK_SET_RATE_PARENT, 0),
+			ENABLE_SCLK_PERIC, 6,
+			CLK_SET_RATE_PARENT | CLK_IGNORE_UNUSED, 0),
 	GATE(CLK_SCLK_SPI2, "sclk_spi2", "sclk_spi2_peric", ENABLE_SCLK_PERIC,
 			5, CLK_SET_RATE_PARENT, 0),
 	GATE(CLK_SCLK_SPI1, "sclk_spi1", "sclk_spi1_peric", ENABLE_SCLK_PERIC,
-- 
2.25.1

[PATCH AUTOSEL 4.9 65/80] clk: bcm2835: Fix return type of bcm2835_register_gate

[Sasha Levin]

From: Nathan Chancellor <natechancellor@gmail.com>

[ Upstream commit f376c43bec4f8ee8d1ba5c5c4cfbd6e84fb279cb ]

bcm2835_register_gate is used as a callback for the clk_register member
of bcm2835_clk_desc, which expects a struct clk_hw * return type but
bcm2835_register_gate returns a struct clk *.

This discrepancy is hidden by the fact that bcm2835_register_gate is
cast to the typedef bcm2835_clk_register by the _REGISTER macro. This
turns out to be a control flow integrity violation, which is how this
was noticed.

Change the return type of bcm2835_register_gate to be struct clk_hw *
and use clk_hw_register_gate to do so. This should be a non-functional
change as clk_register_gate calls clk_hw_register_gate anyways but this
is needed to avoid issues with further changes.

Fixes: b19f009d4510 ("clk: bcm2835: Migrate to clk_hw based registration and OF APIs")
Link: https://github.com/ClangBuiltLinux/linux/issues/1028
Signed-off-by: Nathan Chancellor <natechancellor@gmail.com>
Link: https://lkml.kernel.org/r/20200516080806.1459784-1-natechancellor@gmail.com
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 drivers/clk/bcm/clk-bcm2835.c | 10 +++++-----
 1 file changed, 5 insertions(+), 5 deletions(-)

diff --git a/drivers/clk/bcm/clk-bcm2835.c b/drivers/clk/bcm/clk-bcm2835.c
index 73aab6e984cd..2b5075298cdc 100644
--- a/drivers/clk/bcm/clk-bcm2835.c
+++ b/drivers/clk/bcm/clk-bcm2835.c
@@ -1295,13 +1295,13 @@ static struct clk_hw *bcm2835_register_clock(struct bcm2835_cprman *cprman,
 	return &clock->hw;
 }
 
-static struct clk *bcm2835_register_gate(struct bcm2835_cprman *cprman,
+static struct clk_hw *bcm2835_register_gate(struct bcm2835_cprman *cprman,
 					 const struct bcm2835_gate_data *data)
 {
-	return clk_register_gate(cprman->dev, data->name, data->parent,
-				 CLK_IGNORE_UNUSED | CLK_SET_RATE_GATE,
-				 cprman->regs + data->ctl_reg,
-				 CM_GATE_BIT, 0, &cprman->regs_lock);
+	return clk_hw_register_gate(cprman->dev, data->name, data->parent,
+				    CLK_IGNORE_UNUSED | CLK_SET_RATE_GATE,
+				    cprman->regs + data->ctl_reg,
+				    CM_GATE_BIT, 0, &cprman->regs_lock);
 }
 
 typedef struct clk_hw *(*bcm2835_clk_register)(struct bcm2835_cprman *cprman,
-- 
2.25.1