[PATCHv2 00/31] ARM: dts: r8a779[0-4]: Reference both DMA controllers

[PATCHv2 00/31] ARM: dts: r8a779[0-4]: Reference both DMA controllers

[Niklas Söderlund]

Hi,

R-Car Gen2 have two DMA controllers, which are equivalent. However DMA
slaves were tied only to a single DMA controller in .dtsi. This series
add references to to both DMA controllers for all nodes that previously
only referenced one of them. It also adds dma references to the SDHI
nodes for r8a7794 which according to the datasheet should work but I
have not access to HW to verify.

Tested on Koelsch (r8a7791) by altering the compatible value of either
dmac0 or dmac1 and verifying that the DMA slaves pick the DMA controller
that is instantiated.

For your convince the series can be fetched from
https://git.ragnatech.se/linux rcar-dmas-dt-2

* Changes since v1
- Rebase on top of renesas-devel-20160315-v4.5 and add dmas references
  new nodes (r8a7790: scif2 r8a7793: i2c6,i2c7,i2c8).
- Correct error in commit message 31/31 (s/QSPI/MMCIF).
- Collect Ack and Reviewed tags from Geert.

Niklas Söderlund (31):
  ARM: dts: r8a7790: Reference both DMA controllers in SCIFA nodes
  ARM: dts: r8a7790: Reference both DMA controllers in SCIFB nodes
  ARM: dts: r8a7790: Reference both DMA controllers in HSCIF nodes
  ARM: dts: r8a7790: Reference both DMA controllers in SCIF nodes
  ARM: dts: r8a7790: Reference both DMA controllers in MSIOF nodes
  ARM: dts: r8a7790: Reference both DMA controllers in QSPI node
  ARM: dts: r8a7790: Reference both DMA controllers in IIC nodes
  ARM: dts: r8a7790: Reference both DMA controllers in SDHI nodes
  ARM: dts: r8a7790: Reference both DMA controllers in MMCIF nodes
  ARM: dts: r8a7791: Reference both DMA controllers in SCIFA nodes
  ARM: dts: r8a7791: Reference both DMA controllers in SCIFB nodes
  ARM: dts: r8a7791: Reference both DMA controllers in HSCIF nodes
  ARM: dts: r8a7791: Reference both DMA controllers in SCIF nodes
  ARM: dts: r8a7791: Reference both DMA controllers in MSIOF nodes
  ARM: dts: r8a7791: Reference both DMA controllers in QSPI node
  ARM: dts: r8a7791: Reference both DMA controllers in IIC nodes
  ARM: dts: r8a7791: Reference both DMA controllers in SDHI nodes
  ARM: dts: r8a7791: Reference both DMA controllers in MMCIF node
  ARM: dts: r8a7793: Reference both DMA controllers in SCIFA nodes
  ARM: dts: r8a7793: Reference both DMA controllers in SCIFB nodes
  ARM: dts: r8a7793: Reference both DMA controllers in HSCIF nodes
  ARM: dts: r8a7793: Reference both DMA controllers in SCIF nodes
  ARM: dts: r8a7793: Reference both DMA controllers in QSPI node
  ARM: dts: r8a7793: Reference both DMA controllers in IIC nodes
  ARM: dts: r8a7794: Reference both DMA controllers in SCIFA nodes
  ARM: dts: r8a7794: Reference both DMA controllers in SCIFB nodes
  ARM: dts: r8a7794: Reference both DMA controllers in HSCIF nodes
  ARM: dts: r8a7794: Reference both DMA controllers in SCIF nodes
  ARM: dts: r8a7794: Reference both DMA controllers in QSPI node
  ARM: dts: r8a7794: Reference both DMA controllers in SDHI nodes
  ARM: dts: r8a7794: Reference both DMA controllers in MMCIF node

 arch/arm/boot/dts/r8a7790.dtsi | 130 +++++++++++++++++++++---------------
 arch/arm/boot/dts/r8a7791.dtsi | 145 ++++++++++++++++++++++++-----------------
 arch/arm/boot/dts/r8a7793.dtsi | 110 ++++++++++++++++++-------------
 arch/arm/boot/dts/r8a7794.dtsi | 109 +++++++++++++++++++------------
 4 files changed, 300 insertions(+), 194 deletions(-)

--
2.7.2

[PATCHv2 01/31] ARM: dts: r8a7790: Reference both DMA controllers in SCIFA nodes

[Niklas Söderlund]

R-Car Gen2 have two DMA controllers, which are equivalent. Add
references to both dmac0 and dmac1 so the driver can fallback to the
later if the first one is unavailable.

Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
---
 arch/arm/boot/dts/r8a7790.dtsi | 15 +++++++++------
 1 file changed, 9 insertions(+), 6 deletions(-)

diff --git a/arch/arm/boot/dts/r8a7790.dtsi b/arch/arm/boot/dts/r8a7790.dtsi
index 0077de7..7d9ff0b 100644
--- a/arch/arm/boot/dts/r8a7790.dtsi
+++ b/arch/arm/boot/dts/r8a7790.dtsi
@@ -633,8 +633,9 @@
 		interrupts = <GIC_SPI 144 IRQ_TYPE_LEVEL_HIGH>;
 		clocks = <&mstp2_clks R8A7790_CLK_SCIFA0>;
 		clock-names = "fck";
-		dmas = <&dmac0 0x21>, <&dmac0 0x22>;
-		dma-names = "tx", "rx";
+		dmas = <&dmac0 0x21>, <&dmac0 0x22>,
+		       <&dmac1 0x21>, <&dmac1 0x22>;
+		dma-names = "tx", "rx", "tx", "rx";
 		power-domains = <&cpg_clocks>;
 		status = "disabled";
 	};
@@ -646,8 +647,9 @@
 		interrupts = <GIC_SPI 145 IRQ_TYPE_LEVEL_HIGH>;
 		clocks = <&mstp2_clks R8A7790_CLK_SCIFA1>;
 		clock-names = "fck";
-		dmas = <&dmac0 0x25>, <&dmac0 0x26>;
-		dma-names = "tx", "rx";
+		dmas = <&dmac0 0x25>, <&dmac0 0x26>,
+		       <&dmac1 0x25>, <&dmac1 0x26>;
+		dma-names = "tx", "rx", "tx", "rx";
 		power-domains = <&cpg_clocks>;
 		status = "disabled";
 	};
@@ -659,8 +661,9 @@
 		interrupts = <GIC_SPI 151 IRQ_TYPE_LEVEL_HIGH>;
 		clocks = <&mstp2_clks R8A7790_CLK_SCIFA2>;
 		clock-names = "fck";
-		dmas = <&dmac0 0x27>, <&dmac0 0x28>;
-		dma-names = "tx", "rx";
+		dmas = <&dmac0 0x27>, <&dmac0 0x28>,
+		       <&dmac1 0x27>, <&dmac1 0x28>;
+		dma-names = "tx", "rx", "tx", "rx";
 		power-domains = <&cpg_clocks>;
 		status = "disabled";
 	};
-- 
2.7.2

[PATCHv2 02/31] ARM: dts: r8a7790: Reference both DMA controllers in SCIFB nodes

[Niklas Söderlund]

R-Car Gen2 have two DMA controllers, which are equivalent. Add
references to both dmac0 and dmac1 so the driver can fallback to the
later if the first one is unavailable.

Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
---
 arch/arm/boot/dts/r8a7790.dtsi | 15 +++++++++------
 1 file changed, 9 insertions(+), 6 deletions(-)

diff --git a/arch/arm/boot/dts/r8a7790.dtsi b/arch/arm/boot/dts/r8a7790.dtsi
index 7d9ff0b..13e8817 100644
--- a/arch/arm/boot/dts/r8a7790.dtsi
+++ b/arch/arm/boot/dts/r8a7790.dtsi
@@ -675,8 +675,9 @@
 		interrupts = <GIC_SPI 148 IRQ_TYPE_LEVEL_HIGH>;
 		clocks = <&mstp2_clks R8A7790_CLK_SCIFB0>;
 		clock-names = "fck";
-		dmas = <&dmac0 0x3d>, <&dmac0 0x3e>;
-		dma-names = "tx", "rx";
+		dmas = <&dmac0 0x3d>, <&dmac0 0x3e>,
+		       <&dmac1 0x3d>, <&dmac1 0x3e>;
+		dma-names = "tx", "rx", "tx", "rx";
 		power-domains = <&cpg_clocks>;
 		status = "disabled";
 	};
@@ -688,8 +689,9 @@
 		interrupts = <GIC_SPI 149 IRQ_TYPE_LEVEL_HIGH>;
 		clocks = <&mstp2_clks R8A7790_CLK_SCIFB1>;
 		clock-names = "fck";
-		dmas = <&dmac0 0x19>, <&dmac0 0x1a>;
-		dma-names = "tx", "rx";
+		dmas = <&dmac0 0x19>, <&dmac0 0x1a>,
+		       <&dmac1 0x19>, <&dmac1 0x1a>;
+		dma-names = "tx", "rx", "tx", "rx";
 		power-domains = <&cpg_clocks>;
 		status = "disabled";
 	};
@@ -701,8 +703,9 @@
 		interrupts = <GIC_SPI 150 IRQ_TYPE_LEVEL_HIGH>;
 		clocks = <&mstp2_clks R8A7790_CLK_SCIFB2>;
 		clock-names = "fck";
-		dmas = <&dmac0 0x1d>, <&dmac0 0x1e>;
-		dma-names = "tx", "rx";
+		dmas = <&dmac0 0x1d>, <&dmac0 0x1e>,
+		       <&dmac1 0x1d>, <&dmac1 0x1e>;
+		dma-names = "tx", "rx", "tx", "rx";
 		power-domains = <&cpg_clocks>;
 		status = "disabled";
 	};
-- 
2.7.2

[PATCHv2 03/31] ARM: dts: r8a7790: Reference both DMA controllers in HSCIF nodes

[Niklas Söderlund]

R-Car Gen2 have two DMA controllers, which are equivalent. Add
references to both dmac0 and dmac1 so the driver can fallback to the
later if the first one is unavailable.

Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
---
 arch/arm/boot/dts/r8a7790.dtsi | 10 ++++++----
 1 file changed, 6 insertions(+), 4 deletions(-)

diff --git a/arch/arm/boot/dts/r8a7790.dtsi b/arch/arm/boot/dts/r8a7790.dtsi
index 13e8817..2c02493 100644
--- a/arch/arm/boot/dts/r8a7790.dtsi
+++ b/arch/arm/boot/dts/r8a7790.dtsi
@@ -760,8 +760,9 @@
 		clocks = <&mstp7_clks R8A7790_CLK_HSCIF0>, <&zs_clk>,
 			 <&scif_clk>;
 		clock-names = "fck", "brg_int", "scif_clk";
-		dmas = <&dmac0 0x39>, <&dmac0 0x3a>;
-		dma-names = "tx", "rx";
+		dmas = <&dmac0 0x39>, <&dmac0 0x3a>,
+		       <&dmac1 0x39>, <&dmac1 0x3a>;
+		dma-names = "tx", "rx", "tx", "rx";
 		power-domains = <&cpg_clocks>;
 		status = "disabled";
 	};
@@ -774,8 +775,9 @@
 		clocks = <&mstp7_clks R8A7790_CLK_HSCIF1>, <&zs_clk>,
 			 <&scif_clk>;
 		clock-names = "fck", "brg_int", "scif_clk";
-		dmas = <&dmac0 0x4d>, <&dmac0 0x4e>;
-		dma-names = "tx", "rx";
+		dmas = <&dmac0 0x4d>, <&dmac0 0x4e>,
+		       <&dmac1 0x4d>, <&dmac1 0x4e>;
+		dma-names = "tx", "rx", "tx", "rx";
 		power-domains = <&cpg_clocks>;
 		status = "disabled";
 	};
-- 
2.7.2

[PATCHv2 04/31] ARM: dts: r8a7790: Reference both DMA controllers in SCIF nodes

[Niklas Söderlund]

R-Car Gen2 have two DMA controllers, which are equivalent. Add
references to both dmac0 and dmac1 so the driver can fallback to the
later if the first one is unavailable.

Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
---
 arch/arm/boot/dts/r8a7790.dtsi | 15 +++++++++------
 1 file changed, 9 insertions(+), 6 deletions(-)

diff --git a/arch/arm/boot/dts/r8a7790.dtsi b/arch/arm/boot/dts/r8a7790.dtsi
index 2c02493..fe1e995 100644
--- a/arch/arm/boot/dts/r8a7790.dtsi
+++ b/arch/arm/boot/dts/r8a7790.dtsi
@@ -718,8 +718,9 @@
 		clocks = <&mstp7_clks R8A7790_CLK_SCIF0>, <&zs_clk>,
 			 <&scif_clk>;
 		clock-names = "fck", "brg_int", "scif_clk";
-		dmas = <&dmac0 0x29>, <&dmac0 0x2a>;
-		dma-names = "tx", "rx";
+		dmas = <&dmac0 0x29>, <&dmac0 0x2a>,
+		       <&dmac1 0x29>, <&dmac1 0x2a>;
+		dma-names = "tx", "rx", "tx", "rx";
 		power-domains = <&cpg_clocks>;
 		status = "disabled";
 	};
@@ -732,8 +733,9 @@
 		clocks = <&mstp7_clks R8A7790_CLK_SCIF1>, <&zs_clk>,
 			 <&scif_clk>;
 		clock-names = "fck", "brg_int", "scif_clk";
-		dmas = <&dmac0 0x2d>, <&dmac0 0x2e>;
-		dma-names = "tx", "rx";
+		dmas = <&dmac0 0x2d>, <&dmac0 0x2e>,
+		       <&dmac1 0x2d>, <&dmac1 0x2e>;
+		dma-names = "tx", "rx", "tx", "rx";
 		power-domains = <&cpg_clocks>;
 		status = "disabled";
 	};
@@ -746,8 +748,9 @@
 		clocks = <&mstp3_clks R8A7790_CLK_SCIF2>, <&zs_clk>,
 			 <&scif_clk>;
 		clock-names = "fck", "brg_int", "scif_clk";
-		dmas = <&dmac0 0x2b>, <&dmac0 0x2c>;
-		dma-names = "tx", "rx";
+		dmas = <&dmac0 0x2b>, <&dmac0 0x2c>,
+		       <&dmac1 0x2b>, <&dmac1 0x2c>;
+		dma-names = "tx", "rx", "tx", "rx";
 		power-domains = <&cpg_clocks>;
 		status = "disabled";
 	};
-- 
2.7.2

[PATCHv2 05/31] ARM: dts: r8a7790: Reference both DMA controllers in MSIOF nodes

[Niklas Söderlund]

R-Car Gen2 have two DMA controllers, which are equivalent. Add
references to both dmac0 and dmac1 so the driver can fallback to the
later if the first one is unavailable.

Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
---
 arch/arm/boot/dts/r8a7790.dtsi | 20 ++++++++++++--------
 1 file changed, 12 insertions(+), 8 deletions(-)

diff --git a/arch/arm/boot/dts/r8a7790.dtsi b/arch/arm/boot/dts/r8a7790.dtsi
index fe1e995..102973c 100644
--- a/arch/arm/boot/dts/r8a7790.dtsi
+++ b/arch/arm/boot/dts/r8a7790.dtsi
@@ -1508,8 +1508,9 @@
 		reg = <0 0xe6e20000 0 0x0064>;
 		interrupts = <GIC_SPI 156 IRQ_TYPE_LEVEL_HIGH>;
 		clocks = <&mstp0_clks R8A7790_CLK_MSIOF0>;
-		dmas = <&dmac0 0x51>, <&dmac0 0x52>;
-		dma-names = "tx", "rx";
+		dmas = <&dmac0 0x51>, <&dmac0 0x52>,
+		       <&dmac1 0x51>, <&dmac1 0x52>;
+		dma-names = "tx", "rx", "tx", "rx";
 		power-domains = <&cpg_clocks>;
 		#address-cells = <1>;
 		#size-cells = <0>;
@@ -1521,8 +1522,9 @@
 		reg = <0 0xe6e10000 0 0x0064>;
 		interrupts = <GIC_SPI 157 IRQ_TYPE_LEVEL_HIGH>;
 		clocks = <&mstp2_clks R8A7790_CLK_MSIOF1>;
-		dmas = <&dmac0 0x55>, <&dmac0 0x56>;
-		dma-names = "tx", "rx";
+		dmas = <&dmac0 0x55>, <&dmac0 0x56>,
+		       <&dmac1 0x55>, <&dmac1 0x56>;
+		dma-names = "tx", "rx", "tx", "rx";
 		power-domains = <&cpg_clocks>;
 		#address-cells = <1>;
 		#size-cells = <0>;
@@ -1534,8 +1536,9 @@
 		reg = <0 0xe6e00000 0 0x0064>;
 		interrupts = <GIC_SPI 158 IRQ_TYPE_LEVEL_HIGH>;
 		clocks = <&mstp2_clks R8A7790_CLK_MSIOF2>;
-		dmas = <&dmac0 0x41>, <&dmac0 0x42>;
-		dma-names = "tx", "rx";
+		dmas = <&dmac0 0x41>, <&dmac0 0x42>,
+		       <&dmac1 0x41>, <&dmac1 0x42>;
+		dma-names = "tx", "rx", "tx", "rx";
 		power-domains = <&cpg_clocks>;
 		#address-cells = <1>;
 		#size-cells = <0>;
@@ -1547,8 +1550,9 @@
 		reg = <0 0xe6c90000 0 0x0064>;
 		interrupts = <GIC_SPI 159 IRQ_TYPE_LEVEL_HIGH>;
 		clocks = <&mstp2_clks R8A7790_CLK_MSIOF3>;
-		dmas = <&dmac0 0x45>, <&dmac0 0x46>;
-		dma-names = "tx", "rx";
+		dmas = <&dmac0 0x45>, <&dmac0 0x46>,
+		       <&dmac1 0x45>, <&dmac1 0x46>;
+		dma-names = "tx", "rx", "tx", "rx";
 		power-domains = <&cpg_clocks>;
 		#address-cells = <1>;
 		#size-cells = <0>;
-- 
2.7.2

[PATCHv2 06/31] ARM: dts: r8a7790: Reference both DMA controllers in QSPI node

[Niklas Söderlund]

R-Car Gen2 have two DMA controllers, which are equivalent. Add
references to both dmac0 and dmac1 so the driver can fallback to the
later if the first one is unavailable.

Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Acked-by: Geert Uytterhoeven <geert+renesas-gXvu3+zWzMSzQB+pC5nmwQ@public.gmane.org>
---
 arch/arm/boot/dts/r8a7790.dtsi | 5 +++--
 1 file changed, 3 insertions(+), 2 deletions(-)

diff --git a/arch/arm/boot/dts/r8a7790.dtsi b/arch/arm/boot/dts/r8a7790.dtsi
index 102973c..a80791a 100644
--- a/arch/arm/boot/dts/r8a7790.dtsi
+++ b/arch/arm/boot/dts/r8a7790.dtsi
@@ -1494,8 +1494,9 @@
 		reg = <0 0xe6b10000 0 0x2c>;
 		interrupts = <GIC_SPI 184 IRQ_TYPE_LEVEL_HIGH>;
 		clocks = <&mstp9_clks R8A7790_CLK_QSPI_MOD>;
-		dmas = <&dmac0 0x17>, <&dmac0 0x18>;
-		dma-names = "tx", "rx";
+		dmas = <&dmac0 0x17>, <&dmac0 0x18>,
+		       <&dmac1 0x17>, <&dmac1 0x18>;
+		dma-names = "tx", "rx", "tx", "rx";
 		power-domains = <&cpg_clocks>;
 		num-cs = <1>;
 		#address-cells = <1>;
-- 
2.7.2

--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at  http://vger.kernel.org/majordomo-info.html

[PATCHv2 07/31] ARM: dts: r8a7790: Reference both DMA controllers in IIC nodes

[Niklas Söderlund]

R-Car Gen2 have two DMA controllers, which are equivalent. Add
references to both dmac0 and dmac1 so the driver can fallback to the
later if the first one is unavailable.

Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
---
 arch/arm/boot/dts/r8a7790.dtsi | 20 ++++++++++++--------
 1 file changed, 12 insertions(+), 8 deletions(-)

diff --git a/arch/arm/boot/dts/r8a7790.dtsi b/arch/arm/boot/dts/r8a7790.dtsi
index a80791a..cfa91f0 100644
--- a/arch/arm/boot/dts/r8a7790.dtsi
+++ b/arch/arm/boot/dts/r8a7790.dtsi
@@ -506,8 +506,9 @@
 		reg = <0 0xe6500000 0 0x425>;
 		interrupts = <GIC_SPI 174 IRQ_TYPE_LEVEL_HIGH>;
 		clocks = <&mstp3_clks R8A7790_CLK_IIC0>;
-		dmas = <&dmac0 0x61>, <&dmac0 0x62>;
-		dma-names = "tx", "rx";
+		dmas = <&dmac0 0x61>, <&dmac0 0x62>,
+		       <&dmac1 0x61>, <&dmac1 0x62>;
+		dma-names = "tx", "rx", "tx", "rx";
 		power-domains = <&cpg_clocks>;
 		status = "disabled";
 	};
@@ -519,8 +520,9 @@
 		reg = <0 0xe6510000 0 0x425>;
 		interrupts = <GIC_SPI 175 IRQ_TYPE_LEVEL_HIGH>;
 		clocks = <&mstp3_clks R8A7790_CLK_IIC1>;
-		dmas = <&dmac0 0x65>, <&dmac0 0x66>;
-		dma-names = "tx", "rx";
+		dmas = <&dmac0 0x65>, <&dmac0 0x66>,
+		       <&dmac1 0x65>, <&dmac1 0x66>;
+		dma-names = "tx", "rx", "tx", "rx";
 		power-domains = <&cpg_clocks>;
 		status = "disabled";
 	};
@@ -532,8 +534,9 @@
 		reg = <0 0xe6520000 0 0x425>;
 		interrupts = <GIC_SPI 176 IRQ_TYPE_LEVEL_HIGH>;
 		clocks = <&mstp3_clks R8A7790_CLK_IIC2>;
-		dmas = <&dmac0 0x69>, <&dmac0 0x6a>;
-		dma-names = "tx", "rx";
+		dmas = <&dmac0 0x69>, <&dmac0 0x6a>,
+		       <&dmac1 0x69>, <&dmac1 0x6a>;
+		dma-names = "tx", "rx", "tx", "rx";
 		power-domains = <&cpg_clocks>;
 		status = "disabled";
 	};
@@ -545,8 +548,9 @@
 		reg = <0 0xe60b0000 0 0x425>;
 		interrupts = <GIC_SPI 173 IRQ_TYPE_LEVEL_HIGH>;
 		clocks = <&mstp9_clks R8A7790_CLK_IICDVFS>;
-		dmas = <&dmac0 0x77>, <&dmac0 0x78>;
-		dma-names = "tx", "rx";
+		dmas = <&dmac0 0x77>, <&dmac0 0x78>,
+		       <&dmac1 0x77>, <&dmac1 0x78>;
+		dma-names = "tx", "rx", "tx", "rx";
 		power-domains = <&cpg_clocks>;
 		status = "disabled";
 	};
-- 
2.7.2

[PATCHv2 08/31] ARM: dts: r8a7790: Reference both DMA controllers in SDHI nodes

[Niklas Söderlund]

R-Car Gen2 have two DMA controllers, which are equivalent. Add
references to both dmac0 and dmac1 so the driver can fallback to the
later if the first one is unavailable.

Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
---
 arch/arm/boot/dts/r8a7790.dtsi | 20 ++++++++++++--------
 1 file changed, 12 insertions(+), 8 deletions(-)

diff --git a/arch/arm/boot/dts/r8a7790.dtsi b/arch/arm/boot/dts/r8a7790.dtsi
index cfa91f0..31b9b0a 100644
--- a/arch/arm/boot/dts/r8a7790.dtsi
+++ b/arch/arm/boot/dts/r8a7790.dtsi
@@ -591,8 +591,9 @@
 		reg = <0 0xee100000 0 0x328>;
 		interrupts = <GIC_SPI 165 IRQ_TYPE_LEVEL_HIGH>;
 		clocks = <&mstp3_clks R8A7790_CLK_SDHI0>;
-		dmas = <&dmac1 0xcd>, <&dmac1 0xce>;
-		dma-names = "tx", "rx";
+		dmas = <&dmac1 0xcd>, <&dmac1 0xce>,
+		       <&dmac0 0xcd>, <&dmac0 0xce>;
+		dma-names = "tx", "rx", "tx", "rx";
 		power-domains = <&cpg_clocks>;
 		status = "disabled";
 	};
@@ -602,8 +603,9 @@
 		reg = <0 0xee120000 0 0x328>;
 		interrupts = <GIC_SPI 166 IRQ_TYPE_LEVEL_HIGH>;
 		clocks = <&mstp3_clks R8A7790_CLK_SDHI1>;
-		dmas = <&dmac1 0xc9>, <&dmac1 0xca>;
-		dma-names = "tx", "rx";
+		dmas = <&dmac1 0xc9>, <&dmac1 0xca>,
+		       <&dmac0 0xc9>, <&dmac0 0xca>;
+		dma-names = "tx", "rx", "tx", "rx";
 		power-domains = <&cpg_clocks>;
 		status = "disabled";
 	};
@@ -613,8 +615,9 @@
 		reg = <0 0xee140000 0 0x100>;
 		interrupts = <GIC_SPI 167 IRQ_TYPE_LEVEL_HIGH>;
 		clocks = <&mstp3_clks R8A7790_CLK_SDHI2>;
-		dmas = <&dmac1 0xc1>, <&dmac1 0xc2>;
-		dma-names = "tx", "rx";
+		dmas = <&dmac1 0xc1>, <&dmac1 0xc2>,
+		       <&dmac0 0xc1>, <&dmac0 0xc2>;
+		dma-names = "tx", "rx", "tx", "rx";
 		power-domains = <&cpg_clocks>;
 		status = "disabled";
 	};
@@ -624,8 +627,9 @@
 		reg = <0 0xee160000 0 0x100>;
 		interrupts = <GIC_SPI 168 IRQ_TYPE_LEVEL_HIGH>;
 		clocks = <&mstp3_clks R8A7790_CLK_SDHI3>;
-		dmas = <&dmac1 0xd3>, <&dmac1 0xd4>;
-		dma-names = "tx", "rx";
+		dmas = <&dmac1 0xd3>, <&dmac1 0xd4>,
+		       <&dmac0 0xd3>, <&dmac0 0xd4>;
+		dma-names = "tx", "rx", "tx", "rx";
 		power-domains = <&cpg_clocks>;
 		status = "disabled";
 	};
-- 
2.7.2

[PATCHv2 09/31] ARM: dts: r8a7790: Reference both DMA controllers in MMCIF nodes

[Niklas Söderlund]

R-Car Gen2 have two DMA controllers, which are equivalent. Add
references to both dmac0 and dmac1 so the driver can fallback to the
later if the first one is unavailable.

Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
---
 arch/arm/boot/dts/r8a7790.dtsi | 10 ++++++----
 1 file changed, 6 insertions(+), 4 deletions(-)

diff --git a/arch/arm/boot/dts/r8a7790.dtsi b/arch/arm/boot/dts/r8a7790.dtsi
index 31b9b0a..b71b3e2 100644
--- a/arch/arm/boot/dts/r8a7790.dtsi
+++ b/arch/arm/boot/dts/r8a7790.dtsi
@@ -560,8 +560,9 @@
 		reg = <0 0xee200000 0 0x80>;
 		interrupts = <GIC_SPI 169 IRQ_TYPE_LEVEL_HIGH>;
 		clocks = <&mstp3_clks R8A7790_CLK_MMCIF0>;
-		dmas = <&dmac0 0xd1>, <&dmac0 0xd2>;
-		dma-names = "tx", "rx";
+		dmas = <&dmac0 0xd1>, <&dmac0 0xd2>,
+		       <&dmac1 0xd1>, <&dmac1 0xd2>;
+		dma-names = "tx", "rx", "tx", "rx";
 		power-domains = <&cpg_clocks>;
 		reg-io-width = <4>;
 		status = "disabled";
@@ -573,8 +574,9 @@
 		reg = <0 0xee220000 0 0x80>;
 		interrupts = <GIC_SPI 170 IRQ_TYPE_LEVEL_HIGH>;
 		clocks = <&mstp3_clks R8A7790_CLK_MMCIF1>;
-		dmas = <&dmac0 0xe1>, <&dmac0 0xe2>;
-		dma-names = "tx", "rx";
+		dmas = <&dmac0 0xe1>, <&dmac0 0xe2>,
+		       <&dmac1 0xe1>, <&dmac1 0xe2>;
+		dma-names = "tx", "rx", "tx", "rx";
 		power-domains = <&cpg_clocks>;
 		reg-io-width = <4>;
 		status = "disabled";
-- 
2.7.2

[PATCHv2 10/31] ARM: dts: r8a7791: Reference both DMA controllers in SCIFA nodes

[Niklas Söderlund]

R-Car Gen2 have two DMA controllers, which are equivalent. Add
references to both dmac0 and dmac1 so the driver can fallback to the
later if the first one is unavailable.

Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
---
 arch/arm/boot/dts/r8a7791.dtsi | 30 ++++++++++++++++++------------
 1 file changed, 18 insertions(+), 12 deletions(-)

diff --git a/arch/arm/boot/dts/r8a7791.dtsi b/arch/arm/boot/dts/r8a7791.dtsi
index 396a640..4de4812 100644
--- a/arch/arm/boot/dts/r8a7791.dtsi
+++ b/arch/arm/boot/dts/r8a7791.dtsi
@@ -600,8 +600,9 @@
 		interrupts = <GIC_SPI 144 IRQ_TYPE_LEVEL_HIGH>;
 		clocks = <&mstp2_clks R8A7791_CLK_SCIFA0>;
 		clock-names = "fck";
-		dmas = <&dmac0 0x21>, <&dmac0 0x22>;
-		dma-names = "tx", "rx";
+		dmas = <&dmac0 0x21>, <&dmac0 0x22>,
+		       <&dmac1 0x21>, <&dmac1 0x22>;
+		dma-names = "tx", "rx", "tx", "rx";
 		power-domains = <&cpg_clocks>;
 		status = "disabled";
 	};
@@ -613,8 +614,9 @@
 		interrupts = <GIC_SPI 145 IRQ_TYPE_LEVEL_HIGH>;
 		clocks = <&mstp2_clks R8A7791_CLK_SCIFA1>;
 		clock-names = "fck";
-		dmas = <&dmac0 0x25>, <&dmac0 0x26>;
-		dma-names = "tx", "rx";
+		dmas = <&dmac0 0x25>, <&dmac0 0x26>,
+		       <&dmac1 0x25>, <&dmac1 0x26>;
+		dma-names = "tx", "rx", "tx", "rx";
 		power-domains = <&cpg_clocks>;
 		status = "disabled";
 	};
@@ -626,8 +628,9 @@
 		interrupts = <GIC_SPI 151 IRQ_TYPE_LEVEL_HIGH>;
 		clocks = <&mstp2_clks R8A7791_CLK_SCIFA2>;
 		clock-names = "fck";
-		dmas = <&dmac0 0x27>, <&dmac0 0x28>;
-		dma-names = "tx", "rx";
+		dmas = <&dmac0 0x27>, <&dmac0 0x28>,
+		       <&dmac1 0x27>, <&dmac1 0x28>;
+		dma-names = "tx", "rx", "tx", "rx";
 		power-domains = <&cpg_clocks>;
 		status = "disabled";
 	};
@@ -639,8 +642,9 @@
 		interrupts = <GIC_SPI 29 IRQ_TYPE_LEVEL_HIGH>;
 		clocks = <&mstp11_clks R8A7791_CLK_SCIFA3>;
 		clock-names = "fck";
-		dmas = <&dmac0 0x1b>, <&dmac0 0x1c>;
-		dma-names = "tx", "rx";
+		dmas = <&dmac0 0x1b>, <&dmac0 0x1c>,
+		       <&dmac1 0x1b>, <&dmac1 0x1c>;
+		dma-names = "tx", "rx", "tx", "rx";
 		power-domains = <&cpg_clocks>;
 		status = "disabled";
 	};
@@ -652,8 +656,9 @@
 		interrupts = <GIC_SPI 30 IRQ_TYPE_LEVEL_HIGH>;
 		clocks = <&mstp11_clks R8A7791_CLK_SCIFA4>;
 		clock-names = "fck";
-		dmas = <&dmac0 0x1f>, <&dmac0 0x20>;
-		dma-names = "tx", "rx";
+		dmas = <&dmac0 0x1f>, <&dmac0 0x20>,
+		       <&dmac1 0x1f>, <&dmac1 0x20>;
+		dma-names = "tx", "rx", "tx", "rx";
 		power-domains = <&cpg_clocks>;
 		status = "disabled";
 	};
@@ -665,8 +670,9 @@
 		interrupts = <GIC_SPI 31 IRQ_TYPE_LEVEL_HIGH>;
 		clocks = <&mstp11_clks R8A7791_CLK_SCIFA5>;
 		clock-names = "fck";
-		dmas = <&dmac0 0x23>, <&dmac0 0x24>;
-		dma-names = "tx", "rx";
+		dmas = <&dmac0 0x23>, <&dmac0 0x24>,
+		       <&dmac1 0x23>, <&dmac1 0x24>;
+		dma-names = "tx", "rx", "tx", "rx";
 		power-domains = <&cpg_clocks>;
 		status = "disabled";
 	};
-- 
2.7.2

[PATCHv2 11/31] ARM: dts: r8a7791: Reference both DMA controllers in SCIFB nodes

[Niklas Söderlund]

R-Car Gen2 have two DMA controllers, which are equivalent. Add
references to both dmac0 and dmac1 so the driver can fallback to the
later if the first one is unavailable.

Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Acked-by: Geert Uytterhoeven <geert+renesas-gXvu3+zWzMSzQB+pC5nmwQ@public.gmane.org>
---
 arch/arm/boot/dts/r8a7791.dtsi | 15 +++++++++------
 1 file changed, 9 insertions(+), 6 deletions(-)

diff --git a/arch/arm/boot/dts/r8a7791.dtsi b/arch/arm/boot/dts/r8a7791.dtsi
index 4de4812..319e34c 100644
--- a/arch/arm/boot/dts/r8a7791.dtsi
+++ b/arch/arm/boot/dts/r8a7791.dtsi
@@ -684,8 +684,9 @@
 		interrupts = <GIC_SPI 148 IRQ_TYPE_LEVEL_HIGH>;
 		clocks = <&mstp2_clks R8A7791_CLK_SCIFB0>;
 		clock-names = "fck";
-		dmas = <&dmac0 0x3d>, <&dmac0 0x3e>;
-		dma-names = "tx", "rx";
+		dmas = <&dmac0 0x3d>, <&dmac0 0x3e>,
+		       <&dmac1 0x3d>, <&dmac1 0x3e>;
+		dma-names = "tx", "rx", "tx", "rx";
 		power-domains = <&cpg_clocks>;
 		status = "disabled";
 	};
@@ -697,8 +698,9 @@
 		interrupts = <GIC_SPI 149 IRQ_TYPE_LEVEL_HIGH>;
 		clocks = <&mstp2_clks R8A7791_CLK_SCIFB1>;
 		clock-names = "fck";
-		dmas = <&dmac0 0x19>, <&dmac0 0x1a>;
-		dma-names = "tx", "rx";
+		dmas = <&dmac0 0x19>, <&dmac0 0x1a>,
+		       <&dmac1 0x19>, <&dmac1 0x1a>;
+		dma-names = "tx", "rx", "tx", "rx";
 		power-domains = <&cpg_clocks>;
 		status = "disabled";
 	};
@@ -710,8 +712,9 @@
 		interrupts = <GIC_SPI 150 IRQ_TYPE_LEVEL_HIGH>;
 		clocks = <&mstp2_clks R8A7791_CLK_SCIFB2>;
 		clock-names = "fck";
-		dmas = <&dmac0 0x1d>, <&dmac0 0x1e>;
-		dma-names = "tx", "rx";
+		dmas = <&dmac0 0x1d>, <&dmac0 0x1e>,
+		       <&dmac1 0x1d>, <&dmac1 0x1e>;
+		dma-names = "tx", "rx", "tx", "rx";
 		power-domains = <&cpg_clocks>;
 		status = "disabled";
 	};
-- 
2.7.2

--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at  http://vger.kernel.org/majordomo-info.html

[PATCHv2 12/31] ARM: dts: r8a7791: Reference both DMA controllers in HSCIF nodes

[Niklas Söderlund]

R-Car Gen2 have two DMA controllers, which are equivalent. Add
references to both dmac0 and dmac1 so the driver can fallback to the
later if the first one is unavailable.

Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
---
 arch/arm/boot/dts/r8a7791.dtsi | 15 +++++++++------
 1 file changed, 9 insertions(+), 6 deletions(-)

diff --git a/arch/arm/boot/dts/r8a7791.dtsi b/arch/arm/boot/dts/r8a7791.dtsi
index 319e34c..7854a4f 100644
--- a/arch/arm/boot/dts/r8a7791.dtsi
+++ b/arch/arm/boot/dts/r8a7791.dtsi
@@ -811,8 +811,9 @@
 		clocks = <&mstp7_clks R8A7791_CLK_HSCIF0>, <&zs_clk>,
 			 <&scif_clk>;
 		clock-names = "fck", "brg_int", "scif_clk";
-		dmas = <&dmac0 0x39>, <&dmac0 0x3a>;
-		dma-names = "tx", "rx";
+		dmas = <&dmac0 0x39>, <&dmac0 0x3a>,
+		       <&dmac1 0x39>, <&dmac1 0x3a>;
+		dma-names = "tx", "rx", "tx", "rx";
 		power-domains = <&cpg_clocks>;
 		status = "disabled";
 	};
@@ -825,8 +826,9 @@
 		clocks = <&mstp7_clks R8A7791_CLK_HSCIF1>, <&zs_clk>,
 			 <&scif_clk>;
 		clock-names = "fck", "brg_int", "scif_clk";
-		dmas = <&dmac0 0x4d>, <&dmac0 0x4e>;
-		dma-names = "tx", "rx";
+		dmas = <&dmac0 0x4d>, <&dmac0 0x4e>,
+		       <&dmac1 0x4d>, <&dmac1 0x4e>;
+		dma-names = "tx", "rx", "tx", "rx";
 		power-domains = <&cpg_clocks>;
 		status = "disabled";
 	};
@@ -839,8 +841,9 @@
 		clocks = <&mstp7_clks R8A7791_CLK_HSCIF2>, <&zs_clk>,
 			 <&scif_clk>;
 		clock-names = "fck", "brg_int", "scif_clk";
-		dmas = <&dmac0 0x3b>, <&dmac0 0x3c>;
-		dma-names = "tx", "rx";
+		dmas = <&dmac0 0x3b>, <&dmac0 0x3c>,
+		       <&dmac1 0x3b>, <&dmac1 0x3c>;
+		dma-names = "tx", "rx", "tx", "rx";
 		power-domains = <&cpg_clocks>;
 		status = "disabled";
 	};
-- 
2.7.2

[PATCHv2 13/31] ARM: dts: r8a7791: Reference both DMA controllers in SCIF nodes

[Niklas Söderlund]

R-Car Gen2 have two DMA controllers, which are equivalent. Add
references to both dmac0 and dmac1 so the driver can fallback to the
later if the first one is unavailable.

Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
---
 arch/arm/boot/dts/r8a7791.dtsi | 30 ++++++++++++++++++------------
 1 file changed, 18 insertions(+), 12 deletions(-)

diff --git a/arch/arm/boot/dts/r8a7791.dtsi b/arch/arm/boot/dts/r8a7791.dtsi
index 7854a4f..76c8da8 100644
--- a/arch/arm/boot/dts/r8a7791.dtsi
+++ b/arch/arm/boot/dts/r8a7791.dtsi
@@ -727,8 +727,9 @@
 		clocks = <&mstp7_clks R8A7791_CLK_SCIF0>, <&zs_clk>,
 			 <&scif_clk>;
 		clock-names = "fck", "brg_int", "scif_clk";
-		dmas = <&dmac0 0x29>, <&dmac0 0x2a>;
-		dma-names = "tx", "rx";
+		dmas = <&dmac0 0x29>, <&dmac0 0x2a>,
+		       <&dmac1 0x29>, <&dmac1 0x2a>;
+		dma-names = "tx", "rx", "tx", "rx";
 		power-domains = <&cpg_clocks>;
 		status = "disabled";
 	};
@@ -741,8 +742,9 @@
 		clocks = <&mstp7_clks R8A7791_CLK_SCIF1>, <&zs_clk>,
 			 <&scif_clk>;
 		clock-names = "fck", "brg_int", "scif_clk";
-		dmas = <&dmac0 0x2d>, <&dmac0 0x2e>;
-		dma-names = "tx", "rx";
+		dmas = <&dmac0 0x2d>, <&dmac0 0x2e>,
+		       <&dmac1 0x2d>, <&dmac1 0x2e>;
+		dma-names = "tx", "rx", "tx", "rx";
 		power-domains = <&cpg_clocks>;
 		status = "disabled";
 	};
@@ -755,8 +757,9 @@
 		clocks = <&mstp7_clks R8A7791_CLK_SCIF2>, <&zs_clk>,
 			 <&scif_clk>;
 		clock-names = "fck", "brg_int", "scif_clk";
-		dmas = <&dmac0 0x2b>, <&dmac0 0x2c>;
-		dma-names = "tx", "rx";
+		dmas = <&dmac0 0x2b>, <&dmac0 0x2c>,
+		       <&dmac1 0x2b>, <&dmac1 0x2c>;
+		dma-names = "tx", "rx", "tx", "rx";
 		power-domains = <&cpg_clocks>;
 		status = "disabled";
 	};
@@ -769,8 +772,9 @@
 		clocks = <&mstp7_clks R8A7791_CLK_SCIF3>, <&zs_clk>,
 			 <&scif_clk>;
 		clock-names = "fck", "brg_int", "scif_clk";
-		dmas = <&dmac0 0x2f>, <&dmac0 0x30>;
-		dma-names = "tx", "rx";
+		dmas = <&dmac0 0x2f>, <&dmac0 0x30>,
+		       <&dmac1 0x2f>, <&dmac1 0x30>;
+		dma-names = "tx", "rx", "tx", "rx";
 		power-domains = <&cpg_clocks>;
 		status = "disabled";
 	};
@@ -783,8 +787,9 @@
 		clocks = <&mstp7_clks R8A7791_CLK_SCIF4>, <&zs_clk>,
 			 <&scif_clk>;
 		clock-names = "fck", "brg_int", "scif_clk";
-		dmas = <&dmac0 0xfb>, <&dmac0 0xfc>;
-		dma-names = "tx", "rx";
+		dmas = <&dmac0 0xfb>, <&dmac0 0xfc>,
+		       <&dmac1 0xfb>, <&dmac1 0xfc>;
+		dma-names = "tx", "rx", "tx", "rx";
 		power-domains = <&cpg_clocks>;
 		status = "disabled";
 	};
@@ -797,8 +802,9 @@
 		clocks = <&mstp7_clks R8A7791_CLK_SCIF5>, <&zs_clk>,
 			 <&scif_clk>;
 		clock-names = "fck", "brg_int", "scif_clk";
-		dmas = <&dmac0 0xfd>, <&dmac0 0xfe>;
-		dma-names = "tx", "rx";
+		dmas = <&dmac0 0xfd>, <&dmac0 0xfe>,
+		       <&dmac1 0xfd>, <&dmac1 0xfe>;
+		dma-names = "tx", "rx", "tx", "rx";
 		power-domains = <&cpg_clocks>;
 		status = "disabled";
 	};
-- 
2.7.2

[PATCHv2 14/31] ARM: dts: r8a7791: Reference both DMA controllers in MSIOF nodes

[Niklas Söderlund]

R-Car Gen2 have two DMA controllers, which are equivalent. Add
references to both dmac0 and dmac1 so the driver can fallback to the
later if the first one is unavailable.

Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
---
 arch/arm/boot/dts/r8a7791.dtsi | 15 +++++++++------
 1 file changed, 9 insertions(+), 6 deletions(-)

diff --git a/arch/arm/boot/dts/r8a7791.dtsi b/arch/arm/boot/dts/r8a7791.dtsi
index 76c8da8..4d0d7a7 100644
--- a/arch/arm/boot/dts/r8a7791.dtsi
+++ b/arch/arm/boot/dts/r8a7791.dtsi
@@ -1532,8 +1532,9 @@
 		reg = <0 0xe6e20000 0 0x0064>;
 		interrupts = <GIC_SPI 156 IRQ_TYPE_LEVEL_HIGH>;
 		clocks = <&mstp0_clks R8A7791_CLK_MSIOF0>;
-		dmas = <&dmac0 0x51>, <&dmac0 0x52>;
-		dma-names = "tx", "rx";
+		dmas = <&dmac0 0x51>, <&dmac0 0x52>,
+		       <&dmac1 0x51>, <&dmac1 0x52>;
+		dma-names = "tx", "rx", "tx", "rx";
 		power-domains = <&cpg_clocks>;
 		#address-cells = <1>;
 		#size-cells = <0>;
@@ -1545,8 +1546,9 @@
 		reg = <0 0xe6e10000 0 0x0064>;
 		interrupts = <GIC_SPI 157 IRQ_TYPE_LEVEL_HIGH>;
 		clocks = <&mstp2_clks R8A7791_CLK_MSIOF1>;
-		dmas = <&dmac0 0x55>, <&dmac0 0x56>;
-		dma-names = "tx", "rx";
+		dmas = <&dmac0 0x55>, <&dmac0 0x56>,
+		       <&dmac1 0x55>, <&dmac1 0x56>;
+		dma-names = "tx", "rx", "tx", "rx";
 		power-domains = <&cpg_clocks>;
 		#address-cells = <1>;
 		#size-cells = <0>;
@@ -1558,8 +1560,9 @@
 		reg = <0 0xe6e00000 0 0x0064>;
 		interrupts = <GIC_SPI 158 IRQ_TYPE_LEVEL_HIGH>;
 		clocks = <&mstp2_clks R8A7791_CLK_MSIOF2>;
-		dmas = <&dmac0 0x41>, <&dmac0 0x42>;
-		dma-names = "tx", "rx";
+		dmas = <&dmac0 0x41>, <&dmac0 0x42>,
+		       <&dmac1 0x41>, <&dmac1 0x42>;
+		dma-names = "tx", "rx", "tx", "rx";
 		power-domains = <&cpg_clocks>;
 		#address-cells = <1>;
 		#size-cells = <0>;
-- 
2.7.2

[PATCHv2 15/31] ARM: dts: r8a7791: Reference both DMA controllers in QSPI node

[Niklas Söderlund]

R-Car Gen2 have two DMA controllers, which are equivalent. Add
references to both dmac0 and dmac1 so the driver can fallback to the
later if the first one is unavailable.

Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
---
 arch/arm/boot/dts/r8a7791.dtsi | 5 +++--
 1 file changed, 3 insertions(+), 2 deletions(-)

diff --git a/arch/arm/boot/dts/r8a7791.dtsi b/arch/arm/boot/dts/r8a7791.dtsi
index 4d0d7a7..8880e22 100644
--- a/arch/arm/boot/dts/r8a7791.dtsi
+++ b/arch/arm/boot/dts/r8a7791.dtsi
@@ -1518,8 +1518,9 @@
 		reg = <0 0xe6b10000 0 0x2c>;
 		interrupts = <GIC_SPI 184 IRQ_TYPE_LEVEL_HIGH>;
 		clocks = <&mstp9_clks R8A7791_CLK_QSPI_MOD>;
-		dmas = <&dmac0 0x17>, <&dmac0 0x18>;
-		dma-names = "tx", "rx";
+		dmas = <&dmac0 0x17>, <&dmac0 0x18>,
+		       <&dmac1 0x17>, <&dmac1 0x18>;
+		dma-names = "tx", "rx", "tx", "rx";
 		power-domains = <&cpg_clocks>;
 		num-cs = <1>;
 		#address-cells = <1>;
-- 
2.7.2

[PATCHv2 16/31] ARM: dts: r8a7791: Reference both DMA controllers in IIC nodes

[Niklas Söderlund]

R-Car Gen2 have two DMA controllers, which are equivalent. Add
references to both dmac0 and dmac1 so the driver can fallback to the
later if the first one is unavailable.

Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Acked-by: Geert Uytterhoeven <geert+renesas-gXvu3+zWzMSzQB+pC5nmwQ@public.gmane.org>
---
 arch/arm/boot/dts/r8a7791.dtsi | 15 +++++++++------
 1 file changed, 9 insertions(+), 6 deletions(-)

diff --git a/arch/arm/boot/dts/r8a7791.dtsi b/arch/arm/boot/dts/r8a7791.dtsi
index 8880e22..9acecdf 100644
--- a/arch/arm/boot/dts/r8a7791.dtsi
+++ b/arch/arm/boot/dts/r8a7791.dtsi
@@ -510,8 +510,9 @@
 		reg = <0 0xe60b0000 0 0x425>;
 		interrupts = <GIC_SPI 173 IRQ_TYPE_LEVEL_HIGH>;
 		clocks = <&mstp9_clks R8A7791_CLK_IICDVFS>;
-		dmas = <&dmac0 0x77>, <&dmac0 0x78>;
-		dma-names = "tx", "rx";
+		dmas = <&dmac0 0x77>, <&dmac0 0x78>,
+		       <&dmac1 0x77>, <&dmac1 0x78>;
+		dma-names = "tx", "rx", "tx", "rx";
 		power-domains = <&cpg_clocks>;
 		status = "disabled";
 	};
@@ -523,8 +524,9 @@
 		reg = <0 0xe6500000 0 0x425>;
 		interrupts = <GIC_SPI 174 IRQ_TYPE_LEVEL_HIGH>;
 		clocks = <&mstp3_clks R8A7791_CLK_IIC0>;
-		dmas = <&dmac0 0x61>, <&dmac0 0x62>;
-		dma-names = "tx", "rx";
+		dmas = <&dmac0 0x61>, <&dmac0 0x62>,
+		       <&dmac1 0x61>, <&dmac1 0x62>;
+		dma-names = "tx", "rx", "tx", "rx";
 		power-domains = <&cpg_clocks>;
 		status = "disabled";
 	};
@@ -536,8 +538,9 @@
 		reg = <0 0xe6510000 0 0x425>;
 		interrupts = <GIC_SPI 175 IRQ_TYPE_LEVEL_HIGH>;
 		clocks = <&mstp3_clks R8A7791_CLK_IIC1>;
-		dmas = <&dmac0 0x65>, <&dmac0 0x66>;
-		dma-names = "tx", "rx";
+		dmas = <&dmac0 0x65>, <&dmac0 0x66>,
+		       <&dmac1 0x65>, <&dmac1 0x66>;
+		dma-names = "tx", "rx", "tx", "rx";
 		power-domains = <&cpg_clocks>;
 		status = "disabled";
 	};
-- 
2.7.2

--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at  http://vger.kernel.org/majordomo-info.html

[PATCHv2 17/31] ARM: dts: r8a7791: Reference both DMA controllers in SDHI nodes

[Niklas Söderlund]

R-Car Gen2 have two DMA controllers, which are equivalent. Add
references to both dmac0 and dmac1 so the driver can fallback to the
later if the first one is unavailable.

Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Acked-by: Geert Uytterhoeven <geert+renesas-gXvu3+zWzMSzQB+pC5nmwQ@public.gmane.org>
---
 arch/arm/boot/dts/r8a7791.dtsi | 15 +++++++++------
 1 file changed, 9 insertions(+), 6 deletions(-)

diff --git a/arch/arm/boot/dts/r8a7791.dtsi b/arch/arm/boot/dts/r8a7791.dtsi
index 9acecdf..145c5aa 100644
--- a/arch/arm/boot/dts/r8a7791.dtsi
+++ b/arch/arm/boot/dts/r8a7791.dtsi
@@ -568,8 +568,9 @@
 		reg = <0 0xee100000 0 0x328>;
 		interrupts = <GIC_SPI 165 IRQ_TYPE_LEVEL_HIGH>;
 		clocks = <&mstp3_clks R8A7791_CLK_SDHI0>;
-		dmas = <&dmac1 0xcd>, <&dmac1 0xce>;
-		dma-names = "tx", "rx";
+		dmas = <&dmac1 0xcd>, <&dmac1 0xce>,
+		       <&dmac0 0xcd>, <&dmac0 0xce>;
+		dma-names = "tx", "rx", "tx", "rx";
 		power-domains = <&cpg_clocks>;
 		status = "disabled";
 	};
@@ -579,8 +580,9 @@
 		reg = <0 0xee140000 0 0x100>;
 		interrupts = <GIC_SPI 167 IRQ_TYPE_LEVEL_HIGH>;
 		clocks = <&mstp3_clks R8A7791_CLK_SDHI1>;
-		dmas = <&dmac1 0xc1>, <&dmac1 0xc2>;
-		dma-names = "tx", "rx";
+		dmas = <&dmac1 0xc1>, <&dmac1 0xc2>,
+		       <&dmac0 0xc1>, <&dmac0 0xc2>;
+		dma-names = "tx", "rx", "tx", "rx";
 		power-domains = <&cpg_clocks>;
 		status = "disabled";
 	};
@@ -590,8 +592,9 @@
 		reg = <0 0xee160000 0 0x100>;
 		interrupts = <GIC_SPI 168 IRQ_TYPE_LEVEL_HIGH>;
 		clocks = <&mstp3_clks R8A7791_CLK_SDHI2>;
-		dmas = <&dmac1 0xd3>, <&dmac1 0xd4>;
-		dma-names = "tx", "rx";
+		dmas = <&dmac1 0xd3>, <&dmac1 0xd4>,
+		       <&dmac0 0xd3>, <&dmac0 0xd4>;
+		dma-names = "tx", "rx", "tx", "rx";
 		power-domains = <&cpg_clocks>;
 		status = "disabled";
 	};
-- 
2.7.2

--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at  http://vger.kernel.org/majordomo-info.html

[PATCHv2 18/31] ARM: dts: r8a7791: Reference both DMA controllers in MMCIF node

[Niklas Söderlund]

R-Car Gen2 have two DMA controllers, which are equivalent. Add
references to both dmac0 and dmac1 so the driver can fallback to the
later if the first one is unavailable.

Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
---
 arch/arm/boot/dts/r8a7791.dtsi | 5 +++--
 1 file changed, 3 insertions(+), 2 deletions(-)

diff --git a/arch/arm/boot/dts/r8a7791.dtsi b/arch/arm/boot/dts/r8a7791.dtsi
index 145c5aa..5f89b58 100644
--- a/arch/arm/boot/dts/r8a7791.dtsi
+++ b/arch/arm/boot/dts/r8a7791.dtsi
@@ -555,8 +555,9 @@
 		reg = <0 0xee200000 0 0x80>;
 		interrupts = <GIC_SPI 169 IRQ_TYPE_LEVEL_HIGH>;
 		clocks = <&mstp3_clks R8A7791_CLK_MMCIF0>;
-		dmas = <&dmac0 0xd1>, <&dmac0 0xd2>;
-		dma-names = "tx", "rx";
+		dmas = <&dmac0 0xd1>, <&dmac0 0xd2>,
+		       <&dmac1 0xd1>, <&dmac1 0xd2>;
+		dma-names = "tx", "rx", "tx", "rx";
 		power-domains = <&cpg_clocks>;
 		reg-io-width = <4>;
 		status = "disabled";
-- 
2.7.2

[PATCHv2 19/31] ARM: dts: r8a7793: Reference both DMA controllers in SCIFA nodes

[Niklas Söderlund]

R-Car Gen2 have two DMA controllers, which are equivalent. Add
references to both dmac0 and dmac1 so the driver can fallback to the
later if the first one is unavailable.

Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Acked-by: Geert Uytterhoeven <geert+renesas-gXvu3+zWzMSzQB+pC5nmwQ@public.gmane.org>
---
 arch/arm/boot/dts/r8a7793.dtsi | 30 ++++++++++++++++++------------
 1 file changed, 18 insertions(+), 12 deletions(-)

diff --git a/arch/arm/boot/dts/r8a7793.dtsi b/arch/arm/boot/dts/r8a7793.dtsi
index b482159..d833423 100644
--- a/arch/arm/boot/dts/r8a7793.dtsi
+++ b/arch/arm/boot/dts/r8a7793.dtsi
@@ -514,8 +514,9 @@
 		interrupts = <GIC_SPI 144 IRQ_TYPE_LEVEL_HIGH>;
 		clocks = <&mstp2_clks R8A7793_CLK_SCIFA0>;
 		clock-names = "fck";
-		dmas = <&dmac0 0x21>, <&dmac0 0x22>;
-		dma-names = "tx", "rx";
+		dmas = <&dmac0 0x21>, <&dmac0 0x22>,
+		       <&dmac1 0x21>, <&dmac1 0x22>;
+		dma-names = "tx", "rx", "tx", "rx";
 		power-domains = <&cpg_clocks>;
 		status = "disabled";
 	};
@@ -527,8 +528,9 @@
 		interrupts = <GIC_SPI 145 IRQ_TYPE_LEVEL_HIGH>;
 		clocks = <&mstp2_clks R8A7793_CLK_SCIFA1>;
 		clock-names = "fck";
-		dmas = <&dmac0 0x25>, <&dmac0 0x26>;
-		dma-names = "tx", "rx";
+		dmas = <&dmac0 0x25>, <&dmac0 0x26>,
+		       <&dmac1 0x25>, <&dmac1 0x26>;
+		dma-names = "tx", "rx", "tx", "rx";
 		power-domains = <&cpg_clocks>;
 		status = "disabled";
 	};
@@ -540,8 +542,9 @@
 		interrupts = <GIC_SPI 151 IRQ_TYPE_LEVEL_HIGH>;
 		clocks = <&mstp2_clks R8A7793_CLK_SCIFA2>;
 		clock-names = "fck";
-		dmas = <&dmac0 0x27>, <&dmac0 0x28>;
-		dma-names = "tx", "rx";
+		dmas = <&dmac0 0x27>, <&dmac0 0x28>,
+		       <&dmac1 0x27>, <&dmac1 0x28>;
+		dma-names = "tx", "rx", "tx", "rx";
 		power-domains = <&cpg_clocks>;
 		status = "disabled";
 	};
@@ -553,8 +556,9 @@
 		interrupts = <GIC_SPI 29 IRQ_TYPE_LEVEL_HIGH>;
 		clocks = <&mstp11_clks R8A7793_CLK_SCIFA3>;
 		clock-names = "fck";
-		dmas = <&dmac0 0x1b>, <&dmac0 0x1c>;
-		dma-names = "tx", "rx";
+		dmas = <&dmac0 0x1b>, <&dmac0 0x1c>,
+		       <&dmac1 0x1b>, <&dmac1 0x1c>;
+		dma-names = "tx", "rx", "tx", "rx";
 		power-domains = <&cpg_clocks>;
 		status = "disabled";
 	};
@@ -566,8 +570,9 @@
 		interrupts = <GIC_SPI 30 IRQ_TYPE_LEVEL_HIGH>;
 		clocks = <&mstp11_clks R8A7793_CLK_SCIFA4>;
 		clock-names = "fck";
-		dmas = <&dmac0 0x1f>, <&dmac0 0x20>;
-		dma-names = "tx", "rx";
+		dmas = <&dmac0 0x1f>, <&dmac0 0x20>,
+		       <&dmac1 0x1f>, <&dmac1 0x20>;
+		dma-names = "tx", "rx", "tx", "rx";
 		power-domains = <&cpg_clocks>;
 		status = "disabled";
 	};
@@ -579,8 +584,9 @@
 		interrupts = <GIC_SPI 31 IRQ_TYPE_LEVEL_HIGH>;
 		clocks = <&mstp11_clks R8A7793_CLK_SCIFA5>;
 		clock-names = "fck";
-		dmas = <&dmac0 0x23>, <&dmac0 0x24>;
-		dma-names = "tx", "rx";
+		dmas = <&dmac0 0x23>, <&dmac0 0x24>,
+		       <&dmac1 0x23>, <&dmac1 0x24>;
+		dma-names = "tx", "rx", "tx", "rx";
 		power-domains = <&cpg_clocks>;
 		status = "disabled";
 	};
-- 
2.7.2

--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at  http://vger.kernel.org/majordomo-info.html

[PATCHv2 20/31] ARM: dts: r8a7793: Reference both DMA controllers in SCIFB nodes

[Niklas Söderlund]

R-Car Gen2 have two DMA controllers, which are equivalent. Add
references to both dmac0 and dmac1 so the driver can fallback to the
later if the first one is unavailable.

Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
---
 arch/arm/boot/dts/r8a7793.dtsi | 15 +++++++++------
 1 file changed, 9 insertions(+), 6 deletions(-)

diff --git a/arch/arm/boot/dts/r8a7793.dtsi b/arch/arm/boot/dts/r8a7793.dtsi
index d833423..d704790 100644
--- a/arch/arm/boot/dts/r8a7793.dtsi
+++ b/arch/arm/boot/dts/r8a7793.dtsi
@@ -598,8 +598,9 @@
 		interrupts = <GIC_SPI 148 IRQ_TYPE_LEVEL_HIGH>;
 		clocks = <&mstp2_clks R8A7793_CLK_SCIFB0>;
 		clock-names = "fck";
-		dmas = <&dmac0 0x3d>, <&dmac0 0x3e>;
-		dma-names = "tx", "rx";
+		dmas = <&dmac0 0x3d>, <&dmac0 0x3e>,
+		       <&dmac1 0x3d>, <&dmac1 0x3e>;
+		dma-names = "tx", "rx", "tx", "rx";
 		power-domains = <&cpg_clocks>;
 		status = "disabled";
 	};
@@ -611,8 +612,9 @@
 		interrupts = <GIC_SPI 149 IRQ_TYPE_LEVEL_HIGH>;
 		clocks = <&mstp2_clks R8A7793_CLK_SCIFB1>;
 		clock-names = "fck";
-		dmas = <&dmac0 0x19>, <&dmac0 0x1a>;
-		dma-names = "tx", "rx";
+		dmas = <&dmac0 0x19>, <&dmac0 0x1a>,
+		       <&dmac1 0x19>, <&dmac1 0x1a>;
+		dma-names = "tx", "rx", "tx", "rx";
 		power-domains = <&cpg_clocks>;
 		status = "disabled";
 	};
@@ -624,8 +626,9 @@
 		interrupts = <GIC_SPI 150 IRQ_TYPE_LEVEL_HIGH>;
 		clocks = <&mstp2_clks R8A7793_CLK_SCIFB2>;
 		clock-names = "fck";
-		dmas = <&dmac0 0x1d>, <&dmac0 0x1e>;
-		dma-names = "tx", "rx";
+		dmas = <&dmac0 0x1d>, <&dmac0 0x1e>,
+		       <&dmac1 0x1d>, <&dmac1 0x1e>;
+		dma-names = "tx", "rx", "tx", "rx";
 		power-domains = <&cpg_clocks>;
 		status = "disabled";
 	};
-- 
2.7.2

[PATCHv2 21/31] ARM: dts: r8a7793: Reference both DMA controllers in HSCIF nodes

[Niklas Söderlund]

R-Car Gen2 have two DMA controllers, which are equivalent. Add
references to both dmac0 and dmac1 so the driver can fallback to the
later if the first one is unavailable.

Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
---
 arch/arm/boot/dts/r8a7793.dtsi | 15 +++++++++------
 1 file changed, 9 insertions(+), 6 deletions(-)

diff --git a/arch/arm/boot/dts/r8a7793.dtsi b/arch/arm/boot/dts/r8a7793.dtsi
index d704790..be2e1fd 100644
--- a/arch/arm/boot/dts/r8a7793.dtsi
+++ b/arch/arm/boot/dts/r8a7793.dtsi
@@ -725,8 +725,9 @@
 		clocks = <&mstp7_clks R8A7793_CLK_HSCIF0>, <&zs_clk>,
 			 <&scif_clk>;
 		clock-names = "fck", "brg_int", "scif_clk";
-		dmas = <&dmac0 0x39>, <&dmac0 0x3a>;
-		dma-names = "tx", "rx";
+		dmas = <&dmac0 0x39>, <&dmac0 0x3a>,
+		       <&dmac1 0x39>, <&dmac1 0x3a>;
+		dma-names = "tx", "rx", "tx", "rx";
 		power-domains = <&cpg_clocks>;
 		status = "disabled";
 	};
@@ -739,8 +740,9 @@
 		clocks = <&mstp7_clks R8A7793_CLK_HSCIF1>, <&zs_clk>,
 			 <&scif_clk>;
 		clock-names = "fck", "brg_int", "scif_clk";
-		dmas = <&dmac0 0x4d>, <&dmac0 0x4e>;
-		dma-names = "tx", "rx";
+		dmas = <&dmac0 0x4d>, <&dmac0 0x4e>,
+		       <&dmac1 0x4d>, <&dmac1 0x4e>;
+		dma-names = "tx", "rx", "tx", "rx";
 		power-domains = <&cpg_clocks>;
 		status = "disabled";
 	};
@@ -753,8 +755,9 @@
 		clocks = <&mstp7_clks R8A7793_CLK_HSCIF2>, <&zs_clk>,
 			 <&scif_clk>;
 		clock-names = "fck", "brg_int", "scif_clk";
-		dmas = <&dmac0 0x3b>, <&dmac0 0x3c>;
-		dma-names = "tx", "rx";
+		dmas = <&dmac0 0x3b>, <&dmac0 0x3c>,
+		       <&dmac1 0x3b>, <&dmac1 0x3c>;
+		dma-names = "tx", "rx", "tx", "rx";
 		power-domains = <&cpg_clocks>;
 		status = "disabled";
 	};
-- 
2.7.2

[PATCHv2 22/31] ARM: dts: r8a7793: Reference both DMA controllers in SCIF nodes

[Niklas Söderlund]

R-Car Gen2 have two DMA controllers, which are equivalent. Add
references to both dmac0 and dmac1 so the driver can fallback to the
later if the first one is unavailable.

Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Acked-by: Geert Uytterhoeven <geert+renesas-gXvu3+zWzMSzQB+pC5nmwQ@public.gmane.org>
---
 arch/arm/boot/dts/r8a7793.dtsi | 30 ++++++++++++++++++------------
 1 file changed, 18 insertions(+), 12 deletions(-)

diff --git a/arch/arm/boot/dts/r8a7793.dtsi b/arch/arm/boot/dts/r8a7793.dtsi
index be2e1fd..88164ac 100644
--- a/arch/arm/boot/dts/r8a7793.dtsi
+++ b/arch/arm/boot/dts/r8a7793.dtsi
@@ -641,8 +641,9 @@
 		clocks = <&mstp7_clks R8A7793_CLK_SCIF0>, <&zs_clk>,
 			 <&scif_clk>;
 		clock-names = "fck", "brg_int", "scif_clk";
-		dmas = <&dmac0 0x29>, <&dmac0 0x2a>;
-		dma-names = "tx", "rx";
+		dmas = <&dmac0 0x29>, <&dmac0 0x2a>,
+		       <&dmac1 0x29>, <&dmac1 0x2a>;
+		dma-names = "tx", "rx", "tx", "rx";
 		power-domains = <&cpg_clocks>;
 		status = "disabled";
 	};
@@ -655,8 +656,9 @@
 		clocks = <&mstp7_clks R8A7793_CLK_SCIF1>, <&zs_clk>,
 			 <&scif_clk>;
 		clock-names = "fck", "brg_int", "scif_clk";
-		dmas = <&dmac0 0x2d>, <&dmac0 0x2e>;
-		dma-names = "tx", "rx";
+		dmas = <&dmac0 0x2d>, <&dmac0 0x2e>,
+		       <&dmac1 0x2d>, <&dmac1 0x2e>;
+		dma-names = "tx", "rx", "tx", "rx";
 		power-domains = <&cpg_clocks>;
 		status = "disabled";
 	};
@@ -669,8 +671,9 @@
 		clocks = <&mstp7_clks R8A7793_CLK_SCIF2>, <&zs_clk>,
 			 <&scif_clk>;
 		clock-names = "fck", "brg_int", "scif_clk";
-		dmas = <&dmac0 0x2b>, <&dmac0 0x2c>;
-		dma-names = "tx", "rx";
+		dmas = <&dmac0 0x2b>, <&dmac0 0x2c>,
+		       <&dmac1 0x2b>, <&dmac1 0x2c>;
+		dma-names = "tx", "rx", "tx", "rx";
 		power-domains = <&cpg_clocks>;
 		status = "disabled";
 	};
@@ -683,8 +686,9 @@
 		clocks = <&mstp7_clks R8A7793_CLK_SCIF3>, <&zs_clk>,
 			 <&scif_clk>;
 		clock-names = "fck", "brg_int", "scif_clk";
-		dmas = <&dmac0 0x2f>, <&dmac0 0x30>;
-		dma-names = "tx", "rx";
+		dmas = <&dmac0 0x2f>, <&dmac0 0x30>,
+		       <&dmac1 0x2f>, <&dmac1 0x30>;
+		dma-names = "tx", "rx", "tx", "rx";
 		power-domains = <&cpg_clocks>;
 		status = "disabled";
 	};
@@ -697,8 +701,9 @@
 		clocks = <&mstp7_clks R8A7793_CLK_SCIF4>, <&zs_clk>,
 			 <&scif_clk>;
 		clock-names = "fck", "brg_int", "scif_clk";
-		dmas = <&dmac0 0xfb>, <&dmac0 0xfc>;
-		dma-names = "tx", "rx";
+		dmas = <&dmac0 0xfb>, <&dmac0 0xfc>,
+		       <&dmac1 0xfb>, <&dmac1 0xfc>;
+		dma-names = "tx", "rx", "tx", "rx";
 		power-domains = <&cpg_clocks>;
 		status = "disabled";
 	};
@@ -711,8 +716,9 @@
 		clocks = <&mstp7_clks R8A7793_CLK_SCIF5>, <&zs_clk>,
 			 <&scif_clk>;
 		clock-names = "fck", "brg_int", "scif_clk";
-		dmas = <&dmac0 0xfd>, <&dmac0 0xfe>;
-		dma-names = "tx", "rx";
+		dmas = <&dmac0 0xfd>, <&dmac0 0xfe>,
+		       <&dmac1 0xfd>, <&dmac1 0xfe>;
+		dma-names = "tx", "rx", "tx", "rx";
 		power-domains = <&cpg_clocks>;
 		status = "disabled";
 	};
-- 
2.7.2

--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at  http://vger.kernel.org/majordomo-info.html

[PATCHv2 23/31] ARM: dts: r8a7793: Reference both DMA controllers in QSPI node

[Niklas Söderlund]

R-Car Gen2 have two DMA controllers, which are equivalent. Add
references to both dmac0 and dmac1 so the driver can fallback to the
later if the first one is unavailable.

Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
---
 arch/arm/boot/dts/r8a7793.dtsi | 5 +++--
 1 file changed, 3 insertions(+), 2 deletions(-)

diff --git a/arch/arm/boot/dts/r8a7793.dtsi b/arch/arm/boot/dts/r8a7793.dtsi
index 88164ac..b16b0cc 100644
--- a/arch/arm/boot/dts/r8a7793.dtsi
+++ b/arch/arm/boot/dts/r8a7793.dtsi
@@ -785,8 +785,9 @@
 		reg = <0 0xe6b10000 0 0x2c>;
 		interrupts = <GIC_SPI 184 IRQ_TYPE_LEVEL_HIGH>;
 		clocks = <&mstp9_clks R8A7793_CLK_QSPI_MOD>;
-		dmas = <&dmac0 0x17>, <&dmac0 0x18>;
-		dma-names = "tx", "rx";
+		dmas = <&dmac0 0x17>, <&dmac0 0x18>,
+		       <&dmac1 0x17>, <&dmac1 0x18>;
+		dma-names = "tx", "rx", "tx", "rx";
 		power-domains = <&cpg_clocks>;
 		num-cs = <1>;
 		#address-cells = <1>;
-- 
2.7.2

[PATCHv2 24/31] ARM: dts: r8a7793: Reference both DMA controllers in IIC nodes

[Niklas Söderlund]

R-Car Gen2 have two DMA controllers, which are equivalent. Add
references to both dmac0 and dmac1 so the driver can fallback to the
later if the first one is unavailable.

Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
---
 arch/arm/boot/dts/r8a7793.dtsi | 15 +++++++++------
 1 file changed, 9 insertions(+), 6 deletions(-)

diff --git a/arch/arm/boot/dts/r8a7793.dtsi b/arch/arm/boot/dts/r8a7793.dtsi
index b16b0cc..90925c5 100644
--- a/arch/arm/boot/dts/r8a7793.dtsi
+++ b/arch/arm/boot/dts/r8a7793.dtsi
@@ -470,8 +470,9 @@
 		reg = <0 0xe60b0000 0 0x425>;
 		interrupts = <GIC_SPI 173 IRQ_TYPE_LEVEL_HIGH>;
 		clocks = <&mstp9_clks R8A7793_CLK_IICDVFS>;
-		dmas = <&dmac0 0x77>, <&dmac0 0x78>;
-		dma-names = "tx", "rx";
+		dmas = <&dmac0 0x77>, <&dmac0 0x78>,
+		       <&dmac1 0x77>, <&dmac1 0x78>;
+		dma-names = "tx", "rx", "tx", "rx";
 		power-domains = <&cpg_clocks>;
 		status = "disabled";
 	};
@@ -483,8 +484,9 @@
 		reg = <0 0xe6500000 0 0x425>;
 		interrupts = <GIC_SPI 174 IRQ_TYPE_LEVEL_HIGH>;
 		clocks = <&mstp3_clks R8A7793_CLK_IIC0>;
-		dmas = <&dmac0 0x61>, <&dmac0 0x62>;
-		dma-names = "tx", "rx";
+		dmas = <&dmac0 0x61>, <&dmac0 0x62>,
+		       <&dmac1 0x61>, <&dmac1 0x62>;
+		dma-names = "tx", "rx", "tx", "rx";
 		power-domains = <&cpg_clocks>;
 		status = "disabled";
 	};
@@ -496,8 +498,9 @@
 		reg = <0 0xe6510000 0 0x425>;
 		interrupts = <GIC_SPI 175 IRQ_TYPE_LEVEL_HIGH>;
 		clocks = <&mstp3_clks R8A7793_CLK_IIC1>;
-		dmas = <&dmac0 0x65>, <&dmac0 0x66>;
-		dma-names = "tx", "rx";
+		dmas = <&dmac0 0x65>, <&dmac0 0x66>,
+		       <&dmac1 0x65>, <&dmac1 0x66>;
+		dma-names = "tx", "rx", "tx", "rx";
 		power-domains = <&cpg_clocks>;
 		status = "disabled";
 	};
-- 
2.7.2

[PATCHv2 25/31] ARM: dts: r8a7794: Reference both DMA controllers in SCIFA nodes

[Niklas Söderlund]

R-Car Gen2 have two DMA controllers, which are equivalent. Add
references to both dmac0 and dmac1 so the driver can fallback to the
later if the first one is unavailable.

Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
---
 arch/arm/boot/dts/r8a7794.dtsi | 30 ++++++++++++++++++------------
 1 file changed, 18 insertions(+), 12 deletions(-)

diff --git a/arch/arm/boot/dts/r8a7794.dtsi b/arch/arm/boot/dts/r8a7794.dtsi
index eacb2b2..4256557 100644
--- a/arch/arm/boot/dts/r8a7794.dtsi
+++ b/arch/arm/boot/dts/r8a7794.dtsi
@@ -296,8 +296,9 @@
 		interrupts = <GIC_SPI 144 IRQ_TYPE_LEVEL_HIGH>;
 		clocks = <&mstp2_clks R8A7794_CLK_SCIFA0>;
 		clock-names = "fck";
-		dmas = <&dmac0 0x21>, <&dmac0 0x22>;
-		dma-names = "tx", "rx";
+		dmas = <&dmac0 0x21>, <&dmac0 0x22>,
+		       <&dmac1 0x21>, <&dmac1 0x22>;
+		dma-names = "tx", "rx", "tx", "rx";
 		power-domains = <&cpg_clocks>;
 		status = "disabled";
 	};
@@ -309,8 +310,9 @@
 		interrupts = <GIC_SPI 145 IRQ_TYPE_LEVEL_HIGH>;
 		clocks = <&mstp2_clks R8A7794_CLK_SCIFA1>;
 		clock-names = "fck";
-		dmas = <&dmac0 0x25>, <&dmac0 0x26>;
-		dma-names = "tx", "rx";
+		dmas = <&dmac0 0x25>, <&dmac0 0x26>,
+		       <&dmac1 0x25>, <&dmac1 0x26>;
+		dma-names = "tx", "rx", "tx", "rx";
 		power-domains = <&cpg_clocks>;
 		status = "disabled";
 	};
@@ -322,8 +324,9 @@
 		interrupts = <GIC_SPI 151 IRQ_TYPE_LEVEL_HIGH>;
 		clocks = <&mstp2_clks R8A7794_CLK_SCIFA2>;
 		clock-names = "fck";
-		dmas = <&dmac0 0x27>, <&dmac0 0x28>;
-		dma-names = "tx", "rx";
+		dmas = <&dmac0 0x27>, <&dmac0 0x28>,
+		       <&dmac1 0x27>, <&dmac1 0x28>;
+		dma-names = "tx", "rx", "tx", "rx";
 		power-domains = <&cpg_clocks>;
 		status = "disabled";
 	};
@@ -335,8 +338,9 @@
 		interrupts = <GIC_SPI 29 IRQ_TYPE_LEVEL_HIGH>;
 		clocks = <&mstp11_clks R8A7794_CLK_SCIFA3>;
 		clock-names = "fck";
-		dmas = <&dmac0 0x1b>, <&dmac0 0x1c>;
-		dma-names = "tx", "rx";
+		dmas = <&dmac0 0x1b>, <&dmac0 0x1c>,
+		       <&dmac1 0x1b>, <&dmac1 0x1c>;
+		dma-names = "tx", "rx", "tx", "rx";
 		power-domains = <&cpg_clocks>;
 		status = "disabled";
 	};
@@ -348,8 +352,9 @@
 		interrupts = <GIC_SPI 30 IRQ_TYPE_LEVEL_HIGH>;
 		clocks = <&mstp11_clks R8A7794_CLK_SCIFA4>;
 		clock-names = "fck";
-		dmas = <&dmac0 0x1f>, <&dmac0 0x20>;
-		dma-names = "tx", "rx";
+		dmas = <&dmac0 0x1f>, <&dmac0 0x20>,
+		       <&dmac1 0x1f>, <&dmac1 0x20>;
+		dma-names = "tx", "rx", "tx", "rx";
 		power-domains = <&cpg_clocks>;
 		status = "disabled";
 	};
@@ -361,8 +366,9 @@
 		interrupts = <GIC_SPI 31 IRQ_TYPE_LEVEL_HIGH>;
 		clocks = <&mstp11_clks R8A7794_CLK_SCIFA5>;
 		clock-names = "fck";
-		dmas = <&dmac0 0x23>, <&dmac0 0x24>;
-		dma-names = "tx", "rx";
+		dmas = <&dmac0 0x23>, <&dmac0 0x24>,
+		       <&dmac1 0x23>, <&dmac1 0x24>;
+		dma-names = "tx", "rx", "tx", "rx";
 		power-domains = <&cpg_clocks>;
 		status = "disabled";
 	};
-- 
2.7.2

[PATCHv2 26/31] ARM: dts: r8a7794: Reference both DMA controllers in SCIFB nodes

[Niklas Söderlund]

R-Car Gen2 have two DMA controllers, which are equivalent. Add
references to both dmac0 and dmac1 so the driver can fallback to the
later if the first one is unavailable.

Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
---
 arch/arm/boot/dts/r8a7794.dtsi | 15 +++++++++------
 1 file changed, 9 insertions(+), 6 deletions(-)

diff --git a/arch/arm/boot/dts/r8a7794.dtsi b/arch/arm/boot/dts/r8a7794.dtsi
index 4256557..ccf3061 100644
--- a/arch/arm/boot/dts/r8a7794.dtsi
+++ b/arch/arm/boot/dts/r8a7794.dtsi
@@ -380,8 +380,9 @@
 		interrupts = <GIC_SPI 148 IRQ_TYPE_LEVEL_HIGH>;
 		clocks = <&mstp2_clks R8A7794_CLK_SCIFB0>;
 		clock-names = "fck";
-		dmas = <&dmac0 0x3d>, <&dmac0 0x3e>;
-		dma-names = "tx", "rx";
+		dmas = <&dmac0 0x3d>, <&dmac0 0x3e>,
+		       <&dmac1 0x3d>, <&dmac1 0x3e>;
+		dma-names = "tx", "rx", "tx", "rx";
 		power-domains = <&cpg_clocks>;
 		status = "disabled";
 	};
@@ -393,8 +394,9 @@
 		interrupts = <GIC_SPI 149 IRQ_TYPE_LEVEL_HIGH>;
 		clocks = <&mstp2_clks R8A7794_CLK_SCIFB1>;
 		clock-names = "fck";
-		dmas = <&dmac0 0x19>, <&dmac0 0x1a>;
-		dma-names = "tx", "rx";
+		dmas = <&dmac0 0x19>, <&dmac0 0x1a>,
+		       <&dmac1 0x19>, <&dmac1 0x1a>;
+		dma-names = "tx", "rx", "tx", "rx";
 		power-domains = <&cpg_clocks>;
 		status = "disabled";
 	};
@@ -406,8 +408,9 @@
 		interrupts = <GIC_SPI 150 IRQ_TYPE_LEVEL_HIGH>;
 		clocks = <&mstp2_clks R8A7794_CLK_SCIFB2>;
 		clock-names = "fck";
-		dmas = <&dmac0 0x1d>, <&dmac0 0x1e>;
-		dma-names = "tx", "rx";
+		dmas = <&dmac0 0x1d>, <&dmac0 0x1e>,
+		       <&dmac1 0x1d>, <&dmac1 0x1e>;
+		dma-names = "tx", "rx", "tx", "rx";
 		power-domains = <&cpg_clocks>;
 		status = "disabled";
 	};
-- 
2.7.2

[PATCHv2 27/31] ARM: dts: r8a7794: Reference both DMA controllers in HSCIF nodes

[Niklas Söderlund]

R-Car Gen2 have two DMA controllers, which are equivalent. Add
references to both dmac0 and dmac1 so the driver can fallback to the
later if the first one is unavailable.

Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Acked-by: Geert Uytterhoeven <geert+renesas-gXvu3+zWzMSzQB+pC5nmwQ@public.gmane.org>
---
 arch/arm/boot/dts/r8a7794.dtsi | 15 +++++++++------
 1 file changed, 9 insertions(+), 6 deletions(-)

diff --git a/arch/arm/boot/dts/r8a7794.dtsi b/arch/arm/boot/dts/r8a7794.dtsi
index ccf3061..bc65153 100644
--- a/arch/arm/boot/dts/r8a7794.dtsi
+++ b/arch/arm/boot/dts/r8a7794.dtsi
@@ -507,8 +507,9 @@
 		clocks = <&mstp7_clks R8A7794_CLK_HSCIF0>, <&zs_clk>,
 			 <&scif_clk>;
 		clock-names = "fck", "brg_int", "scif_clk";
-		dmas = <&dmac0 0x39>, <&dmac0 0x3a>;
-		dma-names = "tx", "rx";
+		dmas = <&dmac0 0x39>, <&dmac0 0x3a>,
+		       <&dmac1 0x39>, <&dmac1 0x3a>;
+		dma-names = "tx", "rx", "tx", "rx";
 		power-domains = <&cpg_clocks>;
 		status = "disabled";
 	};
@@ -521,8 +522,9 @@
 		clocks = <&mstp7_clks R8A7794_CLK_HSCIF1>, <&zs_clk>,
 			 <&scif_clk>;
 		clock-names = "fck", "brg_int", "scif_clk";
-		dmas = <&dmac0 0x4d>, <&dmac0 0x4e>;
-		dma-names = "tx", "rx";
+		dmas = <&dmac0 0x4d>, <&dmac0 0x4e>,
+		       <&dmac1 0x4d>, <&dmac1 0x4e>;
+		dma-names = "tx", "rx", "tx", "rx";
 		power-domains = <&cpg_clocks>;
 		status = "disabled";
 	};
@@ -535,8 +537,9 @@
 		clocks = <&mstp7_clks R8A7794_CLK_HSCIF2>, <&zs_clk>,
 			 <&scif_clk>;
 		clock-names = "fck", "brg_int", "scif_clk";
-		dmas = <&dmac0 0x3b>, <&dmac0 0x3c>;
-		dma-names = "tx", "rx";
+		dmas = <&dmac0 0x3b>, <&dmac0 0x3c>,
+		       <&dmac1 0x3b>, <&dmac1 0x3c>;
+		dma-names = "tx", "rx", "tx", "rx";
 		power-domains = <&cpg_clocks>;
 		status = "disabled";
 	};
-- 
2.7.2

--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at  http://vger.kernel.org/majordomo-info.html

[PATCHv2 28/31] ARM: dts: r8a7794: Reference both DMA controllers in SCIF nodes

[Niklas Söderlund]

R-Car Gen2 have two DMA controllers, which are equivalent. Add
references to both dmac0 and dmac1 so the driver can fallback to the
later if the first one is unavailable.

Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
---
 arch/arm/boot/dts/r8a7794.dtsi | 30 ++++++++++++++++++------------
 1 file changed, 18 insertions(+), 12 deletions(-)

diff --git a/arch/arm/boot/dts/r8a7794.dtsi b/arch/arm/boot/dts/r8a7794.dtsi
index bc65153..982f089 100644
--- a/arch/arm/boot/dts/r8a7794.dtsi
+++ b/arch/arm/boot/dts/r8a7794.dtsi
@@ -423,8 +423,9 @@
 		clocks = <&mstp7_clks R8A7794_CLK_SCIF0>, <&zs_clk>,
 			 <&scif_clk>;
 		clock-names = "fck", "brg_int", "scif_clk";
-		dmas = <&dmac0 0x29>, <&dmac0 0x2a>;
-		dma-names = "tx", "rx";
+		dmas = <&dmac0 0x29>, <&dmac0 0x2a>,
+		       <&dmac1 0x29>, <&dmac1 0x2a>;
+		dma-names = "tx", "rx", "tx", "rx";
 		power-domains = <&cpg_clocks>;
 		status = "disabled";
 	};
@@ -437,8 +438,9 @@
 		clocks = <&mstp7_clks R8A7794_CLK_SCIF1>, <&zs_clk>,
 			 <&scif_clk>;
 		clock-names = "fck", "brg_int", "scif_clk";
-		dmas = <&dmac0 0x2d>, <&dmac0 0x2e>;
-		dma-names = "tx", "rx";
+		dmas = <&dmac0 0x2d>, <&dmac0 0x2e>,
+		       <&dmac1 0x2d>, <&dmac1 0x2e>;
+		dma-names = "tx", "rx", "tx", "rx";
 		power-domains = <&cpg_clocks>;
 		status = "disabled";
 	};
@@ -451,8 +453,9 @@
 		clocks = <&mstp7_clks R8A7794_CLK_SCIF2>, <&zs_clk>,
 			 <&scif_clk>;
 		clock-names = "fck", "brg_int", "scif_clk";
-		dmas = <&dmac0 0x2b>, <&dmac0 0x2c>;
-		dma-names = "tx", "rx";
+		dmas = <&dmac0 0x2b>, <&dmac0 0x2c>,
+		       <&dmac1 0x2b>, <&dmac1 0x2c>;
+		dma-names = "tx", "rx", "tx", "rx";
 		power-domains = <&cpg_clocks>;
 		status = "disabled";
 	};
@@ -465,8 +468,9 @@
 		clocks = <&mstp7_clks R8A7794_CLK_SCIF3>, <&zs_clk>,
 			 <&scif_clk>;
 		clock-names = "fck", "brg_int", "scif_clk";
-		dmas = <&dmac0 0x2f>, <&dmac0 0x30>;
-		dma-names = "tx", "rx";
+		dmas = <&dmac0 0x2f>, <&dmac0 0x30>,
+		       <&dmac1 0x2f>, <&dmac1 0x30>;
+		dma-names = "tx", "rx", "tx", "rx";
 		power-domains = <&cpg_clocks>;
 		status = "disabled";
 	};
@@ -479,8 +483,9 @@
 		clocks = <&mstp7_clks R8A7794_CLK_SCIF4>, <&zs_clk>,
 			 <&scif_clk>;
 		clock-names = "fck", "brg_int", "scif_clk";
-		dmas = <&dmac0 0xfb>, <&dmac0 0xfc>;
-		dma-names = "tx", "rx";
+		dmas = <&dmac0 0xfb>, <&dmac0 0xfc>,
+		       <&dmac1 0xfb>, <&dmac1 0xfc>;
+		dma-names = "tx", "rx", "tx", "rx";
 		power-domains = <&cpg_clocks>;
 		status = "disabled";
 	};
@@ -493,8 +498,9 @@
 		clocks = <&mstp7_clks R8A7794_CLK_SCIF5>, <&zs_clk>,
 			 <&scif_clk>;
 		clock-names = "fck", "brg_int", "scif_clk";
-		dmas = <&dmac0 0xfd>, <&dmac0 0xfe>;
-		dma-names = "tx", "rx";
+		dmas = <&dmac0 0xfd>, <&dmac0 0xfe>,
+		       <&dmac1 0xfd>, <&dmac1 0xfe>;
+		dma-names = "tx", "rx", "tx", "rx";
 		power-domains = <&cpg_clocks>;
 		status = "disabled";
 	};
-- 
2.7.2

[PATCHv2 29/31] ARM: dts: r8a7794: Reference both DMA controllers in QSPI node

[Niklas Söderlund]

R-Car Gen2 have two DMA controllers, which are equivalent. Add
references to both dmac0 and dmac1 so the driver can fallback to the
later if the first one is unavailable.

Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
---
 arch/arm/boot/dts/r8a7794.dtsi | 5 +++--
 1 file changed, 3 insertions(+), 2 deletions(-)

diff --git a/arch/arm/boot/dts/r8a7794.dtsi b/arch/arm/boot/dts/r8a7794.dtsi
index 982f089..4761849 100644
--- a/arch/arm/boot/dts/r8a7794.dtsi
+++ b/arch/arm/boot/dts/r8a7794.dtsi
@@ -691,8 +691,9 @@
 		reg = <0 0xe6b10000 0 0x2c>;
 		interrupts = <GIC_SPI 184 IRQ_TYPE_LEVEL_HIGH>;
 		clocks = <&mstp9_clks R8A7794_CLK_QSPI_MOD>;
-		dmas = <&dmac0 0x17>, <&dmac0 0x18>;
-		dma-names = "tx", "rx";
+		dmas = <&dmac0 0x17>, <&dmac0 0x18>,
+		       <&dmac1 0x17>, <&dmac1 0x18>;
+		dma-names = "tx", "rx", "tx", "rx";
 		power-domains = <&cpg_clocks>;
 		num-cs = <1>;
 		#address-cells = <1>;
-- 
2.7.2

[PATCHv2 30/31] ARM: dts: r8a7794: Reference both DMA controllers in SDHI nodes

[Niklas Söderlund]

R-Car Gen2 have two DMA controllers, which are equivalent. Add
references to both dmac0 and dmac1 so the driver can fallback to the
later if the first one is unavailable.

Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Geert Uytterhoeven <geert+renesas-gXvu3+zWzMSzQB+pC5nmwQ@public.gmane.org>
Acked-by: Geert Uytterhoeven <geert+renesas-gXvu3+zWzMSzQB+pC5nmwQ@public.gmane.org>
---
 arch/arm/boot/dts/r8a7794.dtsi | 9 +++++++++
 1 file changed, 9 insertions(+)

diff --git a/arch/arm/boot/dts/r8a7794.dtsi b/arch/arm/boot/dts/r8a7794.dtsi
index 4761849..ec54246 100644
--- a/arch/arm/boot/dts/r8a7794.dtsi
+++ b/arch/arm/boot/dts/r8a7794.dtsi
@@ -664,6 +664,9 @@
 		reg = <0 0xee100000 0 0x200>;
 		interrupts = <GIC_SPI 165 IRQ_TYPE_LEVEL_HIGH>;
 		clocks = <&mstp3_clks R8A7794_CLK_SDHI0>;
+		dmas = <&dmac1 0xcd>, <&dmac1 0xce>,
+		       <&dmac0 0xcd>, <&dmac0 0xce>;
+		dma-names = "tx", "rx", "tx", "rx";
 		power-domains = <&cpg_clocks>;
 		status = "disabled";
 	};
@@ -673,6 +676,9 @@
 		reg = <0 0xee140000 0 0x100>;
 		interrupts = <GIC_SPI 167 IRQ_TYPE_LEVEL_HIGH>;
 		clocks = <&mstp3_clks R8A7794_CLK_SDHI1>;
+		dmas = <&dmac1 0xc1>, <&dmac1 0xc2>,
+		       <&dmac0 0xc1>, <&dmac0 0xc2>;
+		dma-names = "tx", "rx", "tx", "rx";
 		power-domains = <&cpg_clocks>;
 		status = "disabled";
 	};
@@ -682,6 +688,9 @@
 		reg = <0 0xee160000 0 0x100>;
 		interrupts = <GIC_SPI 168 IRQ_TYPE_LEVEL_HIGH>;
 		clocks = <&mstp3_clks R8A7794_CLK_SDHI2>;
+		dmas = <&dmac1 0xd3>, <&dmac1 0xd4>,
+		       <&dmac0 0xd3>, <&dmac0 0xd4>;
+		dma-names = "tx", "rx", "tx", "rx";
 		power-domains = <&cpg_clocks>;
 		status = "disabled";
 	};
-- 
2.7.2

--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at  http://vger.kernel.org/majordomo-info.html

[PATCHv2 31/31] ARM: dts: r8a7794: Reference both DMA controllers in MMCIF node

[Niklas Söderlund]

R-Car Gen2 have two DMA controllers, which are equivalent. Add
references to both dmac0 and dmac1 so the driver can fallback to the
later if the first one is unavailable.

Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
---
 arch/arm/boot/dts/r8a7794.dtsi | 5 +++--
 1 file changed, 3 insertions(+), 2 deletions(-)

diff --git a/arch/arm/boot/dts/r8a7794.dtsi b/arch/arm/boot/dts/r8a7794.dtsi
index ec54246..1219f75 100644
--- a/arch/arm/boot/dts/r8a7794.dtsi
+++ b/arch/arm/boot/dts/r8a7794.dtsi
@@ -652,8 +652,9 @@
 		reg = <0 0xee200000 0 0x80>;
 		interrupts = <GIC_SPI 169 IRQ_TYPE_LEVEL_HIGH>;
 		clocks = <&mstp3_clks R8A7794_CLK_MMCIF0>;
-		dmas = <&dmac0 0xd1>, <&dmac0 0xd2>;
-		dma-names = "tx", "rx";
+		dmas = <&dmac0 0xd1>, <&dmac0 0xd2>,
+		       <&dmac1 0xd1>, <&dmac1 0xd2>;
+		dma-names = "tx", "rx", "tx", "rx";
 		power-domains = <&cpg_clocks>;
 		reg-io-width = <4>;
 		status = "disabled";
-- 
2.7.2

Re: [PATCHv2 00/31] ARM: dts: r8a779[0-4]: Reference both DMA controllers

[Simon Horman]

On Tue, Mar 15, 2016 at 01:41:37PM +0100, Niklas Söderlund wrote:
> Hi,
> 
> R-Car Gen2 have two DMA controllers, which are equivalent. However DMA
> slaves were tied only to a single DMA controller in .dtsi. This series
> add references to to both DMA controllers for all nodes that previously
> only referenced one of them. It also adds dma references to the SDHI
> nodes for r8a7794 which according to the datasheet should work but I
> have not access to HW to verify.
> 
> Tested on Koelsch (r8a7791) by altering the compatible value of either
> dmac0 or dmac1 and verifying that the DMA slaves pick the DMA controller
> that is instantiated.
> 
> For your convince the series can be fetched from
> https://git.ragnatech.se/linux rcar-dmas-dt-2
> 
> * Changes since v1
> - Rebase on top of renesas-devel-20160315-v4.5 and add dmas references
>   new nodes (r8a7790: scif2 r8a7793: i2c6,i2c7,i2c8).
> - Correct error in commit message 31/31 (s/QSPI/MMCIF).
> - Collect Ack and Reviewed tags from Geert.

Thanks Niklas,

I have queued these up for v4.7.