devicetree.vger.kernel.org archive mirror
 help / color / mirror / Atom feed
From: Rhyland Klein <rklein-DDmLM1+adcrQT0dZR+AlfA@public.gmane.org>
To: Laxman Dewangan
	<ldewangan-DDmLM1+adcrQT0dZR+AlfA@public.gmane.org>,
	Thierry Reding
	<thierry.reding-Re5JQEeQqe8AvxtiuMwx3w@public.gmane.org>
Cc: Stephen Warren <swarren-3lzwWm7+Weoh9ZMKESR00Q@public.gmane.org>,
	Jon Hunter <jonathanh-DDmLM1+adcrQT0dZR+AlfA@public.gmane.org>,
	Alexandre Courbot
	<gnurou-Re5JQEeQqe8AvxtiuMwx3w@public.gmane.org>,
	Andrew Bresticker
	<abrestic-F7+t8E8rja9g9hUCZPvPmw@public.gmane.org>,
	devicetree-u79uwXL29TY76Z2rM5mHXA@public.gmane.org,
	linux-tegra-u79uwXL29TY76Z2rM5mHXA@public.gmane.org,
	linux-kernel-u79uwXL29TY76Z2rM5mHXA@public.gmane.org,
	Rhyland Klein <rklein-DDmLM1+adcrQT0dZR+AlfA@public.gmane.org>
Subject: [PATCH] ARM64: boot: dts: Add regulators for Tegra210 Smaug
Date: Fri, 3 Jun 2016 16:22:45 -0400	[thread overview]
Message-ID: <1464985365-11612-1-git-send-email-rklein@nvidia.com> (raw)

Add regulators to the Tegra210 Smaug DTS file including
support for the max77620 PMIC.

Signed-off-by: Rhyland Klein <rklein-DDmLM1+adcrQT0dZR+AlfA@public.gmane.org>
---
 arch/arm64/boot/dts/nvidia/tegra210-smaug.dts | 350 ++++++++++++++++++++++++++
 1 file changed, 350 insertions(+)

diff --git a/arch/arm64/boot/dts/nvidia/tegra210-smaug.dts b/arch/arm64/boot/dts/nvidia/tegra210-smaug.dts
index 4d89f4e02d98..fdca5b5d79e8 100644
--- a/arch/arm64/boot/dts/nvidia/tegra210-smaug.dts
+++ b/arch/arm64/boot/dts/nvidia/tegra210-smaug.dts
@@ -1,6 +1,7 @@
 /dts-v1/;
 
 #include <dt-bindings/input/input.h>
+#include <dt-bindings/mfd/max77620.h>
 #include <dt-bindings/pinctrl/pinctrl-tegra.h>
 
 #include "tegra210.dtsi"
@@ -1327,6 +1328,269 @@
 		};
 	};
 
+	i2c@7000d000 {
+		status = "okay";
+		clock-frequency = <1000000>;
+
+		max77620: max77620@3c {
+			compatible = "maxim,max77620";
+			reg = <0x3c>;
+			interrupts = <0 86 IRQ_TYPE_NONE>;
+
+			#interrupt-cells = <2>;
+			interrupt-controller;
+
+			gpio-controller;
+			#gpio-cells = <2>;
+
+			pinctrl-names = "default";
+			pinctrl-0 = <&max77620_default>;
+
+			max77620_default: pinmux@0 {
+				pin_gpio {
+					pins = "gpio0", "gpio1", "gpio2", "gpio5",
+					       "gpio6", "gpio7";
+					function = "gpio";
+				};
+
+				/*
+				 * GPIO3 is used to en_pp3300, and it is part of power
+				 * sequence, So it must be sequenced up (automatically
+				 * set by OTP) and down properly.
+				 */
+				pin_gpio3 {
+					pins = "gpio3";
+					function = "fps-out";
+					drive-open-drain = <1>;
+					maxim,active-fps-source = <MAX77620_FPS_SRC_0>;
+					maxim,active-fps-power-up-slot = <4>;
+					maxim,active-fps-power-down-slot = <2>;
+				};
+
+				pin_gpio5_6_7 {
+					pins = "gpio5", "gpio6";
+					function = "gpio";
+					drive-push-pull = <1>;
+				};
+
+				pin_32k {
+					pins = "gpio4";
+					function = "32k-out1";
+				};
+			};
+
+			fps {
+				fps0 {
+					maxim,shutdown-fps-time-period-us = <5120>;
+					maxim,fps-event-source = <MAX77620_FPS_EVENT_SRC_EN0>;
+				};
+
+				fps1 {
+					maxim,shutdown-fps-time-period-us = <5120>;
+					maxim,fps-event-source = <MAX77620_FPS_EVENT_SRC_EN1>;
+					maxim,enable-sleep;
+				};
+
+				fps2 {
+					maxim,fps-event-source = <MAX77620_FPS_EVENT_SRC_EN0>;
+				};
+			};
+
+			regulators {
+				in-ldo0-1-supply = <&pp1350>;
+				in-ldo2-supply = <&pp3300>;
+				in-ldo3-5-supply = <&pp3300>;
+				in-ldo7-8-supply = <&pp1350>;
+
+				ppvar_soc: sd0 {
+					regulator-name = "PPVAR_SOC";
+					regulator-min-microvolt = <825000>;
+					regulator-max-microvolt = <1125000>;
+					regulator-enable-ramp-delay = <146>;
+					regulator-disable-ramp-delay = <4080>;
+					regulator-ramp-delay = <27500>;
+					regulator-ramp-delay-scale = <300>;
+					regulator-always-on;
+					regulator-boot-on;
+					maxim,active-fps-source = <MAX77620_FPS_SRC_1>;
+					maxim,active-fps-power-up-slot = <1>;
+					maxim,active-fps-power-down-slot = <7>;
+				};
+
+				pp1100_sd1: sd1 {
+					regulator-name = "PP1100";
+					regulator-min-microvolt = <1125000>;
+					regulator-max-microvolt = <1125000>;
+					regulator-enable-ramp-delay = <130>;
+					regulator-disable-ramp-delay = <145800>;
+					regulator-ramp-delay = <27500>;
+					regulator-ramp-delay-scale = <300>;
+					regulator-always-on;
+					regulator-boot-on;
+					maxim,active-fps-source = <MAX77620_FPS_SRC_0>;
+					maxim,active-fps-power-up-slot = <5>;
+					maxim,active-fps-power-down-slot = <1>;
+				};
+
+				pp1350: sd2 {
+					regulator-name = "PP1350";
+					regulator-min-microvolt = <1350000>;
+					regulator-max-microvolt = <1350000>;
+					regulator-enable-ramp-delay = <176>;
+					regulator-disable-ramp-delay = <32000>;
+					regulator-ramp-delay = <27500>;
+					regulator-ramp-delay-scale = <350>;
+					regulator-always-on;
+					regulator-boot-on;
+					maxim,active-fps-source = <MAX77620_FPS_SRC_NONE>;
+					maxim,active-fps-power-up-slot = <2>;
+					maxim,active-fps-power-down-slot = <5>;
+				};
+
+				pp1800: sd3 {
+					regulator-name = "PP1800";
+					regulator-min-microvolt = <1800000>;
+					regulator-max-microvolt = <1800000>;
+					regulator-enable-ramp-delay = <242>;
+					regulator-disable-ramp-delay = <118000>;
+					regulator-ramp-delay = <27500>;
+					regulator-ramp-delay-scale = <360>;
+					regulator-always-on;
+					regulator-boot-on;
+					maxim,active-fps-source = <MAX77620_FPS_SRC_0>;
+					maxim,active-fps-power-up-slot = <3>;
+					maxim,active-fps-power-down-slot = <3>;
+				};
+
+				pp1200_avdd: ldo0 {
+					regulator-name = "PP1200_AVDD";
+					regulator-min-microvolt = <1200000>;
+					regulator-max-microvolt = <1200000>;
+					regulator-enable-ramp-delay = <26>;
+					regulator-disable-ramp-delay = <626>;
+					regulator-ramp-delay = <100000>;
+					regulator-ramp-delay-scale = <200>;
+					regulator-boot-on;
+					maxim,active-fps-source = <MAX77620_FPS_SRC_NONE>;
+					maxim,active-fps-power-up-slot = <0>;
+					maxim,active-fps-power-down-slot = <7>;
+				};
+
+				pp1200_rcam: ldo1 {
+					regulator-name = "PP1200_RCAM";
+					regulator-min-microvolt = <1200000>;
+					regulator-max-microvolt = <1200000>;
+					regulator-enable-ramp-delay = <22>;
+					regulator-disable-ramp-delay = <630>;
+					regulator-ramp-delay = <100000>;
+					regulator-ramp-delay-scale = <200>;
+					maxim,active-fps-source = <MAX77620_FPS_SRC_NONE>;
+					maxim,active-fps-power-up-slot = <0>;
+					maxim,active-fps-power-down-slot = <7>;
+				};
+
+				pp_ldo2: ldo2 {
+					regulator-name = "PP_LDO2";
+					regulator-min-microvolt = <1800000>;
+					regulator-max-microvolt = <1800000>;
+					regulator-enable-ramp-delay = <62>;
+					regulator-disable-ramp-delay = <650>;
+					regulator-ramp-delay = <100000>;
+					regulator-ramp-delay-scale = <200>;
+					regulator-always-on;
+					regulator-boot-on;
+					maxim,active-fps-source = <MAX77620_FPS_SRC_NONE>;
+					maxim,active-fps-power-up-slot = <0>;
+					maxim,active-fps-power-down-slot = <7>;
+				};
+
+				pp2800l_rcam: ldo3 {
+					regulator-name = "PP2800L_RCAM";
+					regulator-min-microvolt = <2800000>;
+					regulator-max-microvolt = <2800000>;
+					regulator-enable-ramp-delay = <50>;
+					regulator-disable-ramp-delay = <1110>;
+					regulator-ramp-delay = <100000>;
+					regulator-ramp-delay-scale = <200>;
+					maxim,active-fps-source = <MAX77620_FPS_SRC_NONE>;
+					maxim,active-fps-power-up-slot = <0>;
+					maxim,active-fps-power-down-slot = <7>;
+				};
+
+				pp100_soc_rtc: ldo4 {
+					regulator-name = "PP1100_SOC_RTC";
+					regulator-min-microvolt = <850000>;
+					regulator-max-microvolt = <850000>;
+					regulator-enable-ramp-delay = <22>;
+					regulator-disable-ramp-delay = <610>;
+					regulator-ramp-delay = <100000>;
+					regulator-ramp-delay-scale = <200>;
+					regulator-always-on; /* Check this */
+					regulator-boot-on;
+					maxim,active-fps-source = <MAX77620_FPS_SRC_0>;
+					maxim,active-fps-power-up-slot = <1>;
+					maxim,active-fps-power-down-slot = <7>;
+				};
+
+				pp2800l_fcam: ldo5 {
+					regulator-name = "PP2800L_FCAM";
+					regulator-min-microvolt = <2800000>;
+					regulator-max-microvolt = <2800000>;
+					regulator-enable-ramp-delay = <62>;
+					regulator-disable-ramp-delay = <640>;
+					regulator-ramp-delay = <100000>;
+					regulator-ramp-delay-scale = <200>;
+					maxim,active-fps-source = <MAX77620_FPS_SRC_NONE>;
+					maxim,active-fps-power-up-slot = <0>;
+					maxim,active-fps-power-down-slot = <7>;
+				};
+
+				ldo6 {
+					/* Unused. */
+					regulator-name = "PP_LDO6";
+					regulator-min-microvolt = <1800000>;
+					regulator-max-microvolt = <1800000>;
+					regulator-enable-ramp-delay = <36>;
+					regulator-disable-ramp-delay = <674>;
+					regulator-ramp-delay = <100000>;
+					regulator-ramp-delay-scale = <200>;
+					maxim,active-fps-source = <MAX77620_FPS_SRC_NONE>;
+					maxim,active-fps-power-up-slot = <0>;
+					maxim,active-fps-power-down-slot = <7>;
+				};
+
+				pp1050_avdd: ldo7 {
+					regulator-name = "PP1050_AVDD";
+					regulator-min-microvolt = <1050000>;
+					regulator-max-microvolt = <1050000>;
+					regulator-enable-ramp-delay = <24>;
+					regulator-disable-ramp-delay = <2768>;
+					regulator-ramp-delay = <100000>;
+					regulator-ramp-delay-scale = <200>;
+					regulator-always-on;
+					regulator-boot-on;
+					maxim,active-fps-source = <MAX77620_FPS_SRC_1>;
+					maxim,active-fps-power-up-slot = <3>;
+					maxim,active-fps-power-down-slot = <4>;
+				};
+
+				avddio_1v05: ldo8 {
+					regulator-name = "AVDDIO_1V05";
+					regulator-min-microvolt = <1050000>;
+					regulator-max-microvolt = <1050000>;
+					regulator-enable-ramp-delay = <22>;
+					regulator-disable-ramp-delay = <1160>;
+					regulator-ramp-delay = <100000>;
+					regulator-ramp-delay-scale = <200>;
+					regulator-boot-on;
+					maxim,active-fps-source = <MAX77620_FPS_SRC_NONE>;
+					maxim,active-fps-power-up-slot = <0>;
+					maxim,active-fps-power-down-slot = <7>;
+				};
+			};
+		};
+	};
+
 	pmc@7000e400 {
 		nvidia,invert-interrupt;
 		nvidia,suspend-mode = <0>;
@@ -1421,4 +1685,90 @@
 		compatible = "arm,psci-1.0";
 		method = "smc";
 	};
+
+	regulators {
+		compatible = "simple-bus";
+		device_type = "fixed-regulators";
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		ppvar_sys: regulator@0 {
+			compatible = "regulator-fixed";
+			reg = <0>;
+			regulator-name = "PPVAR_SYS";
+			regulator-min-microvolt = <4400000>;
+			regulator-max-microvolt = <4400000>;
+			regulator-always-on;
+		};
+
+		pplcd_vdd: regulator@1 {
+			compatible = "regulator-fixed";
+			reg = <1>;
+			regulator-name = "PPLCD_VDD";
+			regulator-min-microvolt = <4400000>;
+			regulator-max-microvolt = <4400000>;
+			gpio = <&gpio TEGRA_GPIO(V, 4) 0>;
+			enable-active-high;
+			regulator-boot-on;
+		};
+
+		pp3000_always: regulator@2 {
+			compatible = "regulator-fixed";
+			reg = <2>;
+			regulator-name = "PP3000_ALWAYS";
+			regulator-min-microvolt = <3000000>;
+			regulator-max-microvolt = <3000000>;
+			regulator-always-on;
+		};
+
+		pp3300: regulator@3 {
+			compatible = "regulator-fixed";
+			reg = <3>;
+			regulator-name = "PP3300";
+			regulator-min-microvolt = <3300000>;
+			regulator-max-microvolt = <3300000>;
+			regulator-boot-on;
+			regulator-always-on;
+			gpio = <&max77620 3 0>;
+			enable-active-high;
+		};
+
+		pp5000: regulator@4 {
+			compatible = "regulator-fixed";
+			reg = <4>;
+			regulator-name = "PP5000";
+			regulator-min-microvolt = <5000000>;
+			regulator-max-microvolt = <5000000>;
+			regulator-always-on;
+		};
+
+		pp1800_lcdio: regulator@5 {
+			compatible = "regulator-fixed";
+			reg = <5>;
+			regulator-name = "PP1800_LCDIO";
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+			gpio = <&gpio TEGRA_GPIO(V, 3) 0>;
+			enable-active-high;
+			regulator-boot-on;
+		};
+
+		pp1800_cam: regulator@6 {
+			compatible = "regulator-fixed";
+			reg= <6>;
+			regulator-name = "PP1800_CAM";
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+			gpio = <&gpio TEGRA_GPIO(K, 3) 0>;
+			enable-active-high;
+		};
+
+		usbc_vbus: regulator@7 {
+			compatible = "regulator-fixed";
+			reg = <7>;
+			regulator-name = "USBC_VBUS";
+			regulator-min-microvolt = <5000000>;
+			regulator-max-microvolt = <5000000>;
+		};
+	};
 };
-- 
1.9.1

             reply	other threads:[~2016-06-03 20:22 UTC|newest]

Thread overview: 4+ messages / expand[flat|nested]  mbox.gz  Atom feed  top
2016-06-03 20:22 Rhyland Klein [this message]
     [not found] ` <1464985365-11612-1-git-send-email-rklein-DDmLM1+adcrQT0dZR+AlfA@public.gmane.org>
2016-06-06  6:39   ` [PATCH] ARM64: boot: dts: Add regulators for Tegra210 Smaug Laxman Dewangan
2016-06-06 21:52     ` Rhyland Klein
     [not found]       ` <b28b44d9-7f3e-c1bb-7df8-238191ab1941-DDmLM1+adcrQT0dZR+AlfA@public.gmane.org>
2016-06-07 11:35         ` Laxman Dewangan

Reply instructions:

You may reply publicly to this message via plain-text email
using any one of the following methods:

* Save the following mbox file, import it into your mail client,
  and reply-to-all from there: mbox

  Avoid top-posting and favor interleaved quoting:
  https://en.wikipedia.org/wiki/Posting_style#Interleaved_style

* Reply using the --to, --cc, and --in-reply-to
  switches of git-send-email(1):

  git send-email \
    --in-reply-to=1464985365-11612-1-git-send-email-rklein@nvidia.com \
    --to=rklein-ddmlm1+adcrqt0dzr+alfa@public.gmane.org \
    --cc=abrestic-F7+t8E8rja9g9hUCZPvPmw@public.gmane.org \
    --cc=devicetree-u79uwXL29TY76Z2rM5mHXA@public.gmane.org \
    --cc=gnurou-Re5JQEeQqe8AvxtiuMwx3w@public.gmane.org \
    --cc=jonathanh-DDmLM1+adcrQT0dZR+AlfA@public.gmane.org \
    --cc=ldewangan-DDmLM1+adcrQT0dZR+AlfA@public.gmane.org \
    --cc=linux-kernel-u79uwXL29TY76Z2rM5mHXA@public.gmane.org \
    --cc=linux-tegra-u79uwXL29TY76Z2rM5mHXA@public.gmane.org \
    --cc=swarren-3lzwWm7+Weoh9ZMKESR00Q@public.gmane.org \
    --cc=thierry.reding-Re5JQEeQqe8AvxtiuMwx3w@public.gmane.org \
    /path/to/YOUR_REPLY

  https://kernel.org/pub/software/scm/git/docs/git-send-email.html

* If your mail client supports setting the In-Reply-To header
  via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line before the message body. 
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).