[PATCH v5 0/6] ARM: dts: Add PHYTEC phyCORE-i.MX 6 and phyBOARD-Mira carrier board support

[PATCH v5 0/6] ARM: dts: Add PHYTEC phyCORE-i.MX 6 and phyBOARD-Mira carrier board support

[Stefan Riedmueller]

This patchset adds support for the PHYTEC phyCORE-i.MX 6 and phyBOARD-Mira.

Following boards are included:
phyBOARD-Mira with phyCORE-i.MX 6 Quad/Dual with:
- i.MX 6Quad/Dual SOC
- NAND or eMMC
- HDMI interface
- LVDS display interface
- Gigabit Ethernet
- USB Host
- CAN
- RS232
- PCIe
This board also contains an LVDS camera interface and parallel display
interface which are not yet supported.

phyBAORD-Mira with phyCORE-i.MX 6 DualLight/Solo with:
- i.MX 6DualLight/Solo
- NAND
- HDMI interface
- 100 MBit/s Ethernet
- USB Host
- RS232

phyBOARD-Mira with phyCORE-i.MX 6 QuadPlus with:
- i.MX 6QuadPlus SOC
- NAND
- HDMI interface
- LVDS display interface
- Gigabit Ethernet
- USB Host
- CAN
- RS232
- PCIe
This board also contains an LVDS camera interface and parallel display
interface which are not yet supported.

The entire series is based on v4.15-rc4.

Changes since v1:
- Removed unnecessary ipu aliases
- Added unit-address to memory node name
- Fixed eeprom compatible to correct vendor name (atmel instead of cat)
- Fixed rtc compatible to correct vendor name (microcrystal instead of mc)
- Changed pcie regulator to be used with vpcie-supply in &pcie node and
  removed regulator-always-on
- Changed pcie reset-gpio polarity to GPIO_ACTIVE_LOW
- Replaced fsl,uart-has-rtscts by uart-has-rtscts
- Fixed typos in defconfig patch

Changes since v2:
- Fixed typo in patch subject PATCH 4/6
- Added reviewed by tags on PATCH 4/6 and PATCH 6/6

Changes since v3:
- Removed model and compatible from phycore dtsi
- Changed flash compatible to jedec,spi-nor
- Renamed some_green node to som-led-green
- Dropped labels for eeprom, pmic, da9062_wdt and da9062_reg
- Renamed flash label to m25p80
- Put compatible at beginning of property lists
- Changed copyright year to 2018
- Added reviewed by tags on PATCH 1/6, 2/6, 3/6 and 5/6

Changes since v4:
- Rearranged &m25p80 node in dts files to fit alphabetical order
- Fixed a parenthesis for uniformity in mira dtsi

Christian Hemp (2):
  ARM: dts: imx6: Add support for phyBOARD-Mira i.MX 6Quad/Dual RDK
  ARM: dts: imx6: Add support for phyBOARD-Mira i.MX 6 DualLight/Solo
    RDK

Enrico Scholz (1):
  ARM: dts: imx6: Add support for phyBOARD-Mira with i.MX 6QuadPlus

Stefan Riedmueller (3):
  ARM: dts: imx6: Add initial support for phyCORE-i.MX 6 SOM
  ARM: dts: imx6: Add initial support for phyBOARD-Mira
  ARM: imx_v6_v7_defconfig: Enable Dialog Semiconductor DA9062 driver

 arch/arm/boot/dts/Makefile                        |   4 +
 arch/arm/boot/dts/imx6dl-phytec-mira-rdk-nand.dts |  64 ++++
 arch/arm/boot/dts/imx6q-phytec-mira-rdk-emmc.dts  |  72 ++++
 arch/arm/boot/dts/imx6q-phytec-mira-rdk-nand.dts  |  72 ++++
 arch/arm/boot/dts/imx6qdl-phytec-mira.dtsi        | 390 ++++++++++++++++++++++
 arch/arm/boot/dts/imx6qdl-phytec-phycore-som.dtsi | 279 ++++++++++++++++
 arch/arm/boot/dts/imx6qp-phytec-mira-rdk-nand.dts |  72 ++++
 arch/arm/configs/imx_v6_v7_defconfig              |   4 +
 8 files changed, 957 insertions(+)
 create mode 100644 arch/arm/boot/dts/imx6dl-phytec-mira-rdk-nand.dts
 create mode 100644 arch/arm/boot/dts/imx6q-phytec-mira-rdk-emmc.dts
 create mode 100644 arch/arm/boot/dts/imx6q-phytec-mira-rdk-nand.dts
 create mode 100644 arch/arm/boot/dts/imx6qdl-phytec-mira.dtsi
 create mode 100644 arch/arm/boot/dts/imx6qdl-phytec-phycore-som.dtsi
 create mode 100644 arch/arm/boot/dts/imx6qp-phytec-mira-rdk-nand.dts

-- 
2.7.4

--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at  http://vger.kernel.org/majordomo-info.html

[PATCH v5 1/6] ARM: dts: imx6: Add initial support for phyCORE-i.MX 6 SOM

[Stefan Riedmueller]

This patch adds basic support for PHYTEC phyCORE-i.MX 6 SOM with i.MX
6Quad/Dual or i.MX 6DualLight/Solo.

Signed-off-by: Christian Hemp <c.hemp-guT5V/WYfQezQB+pC5nmwQ@public.gmane.org>
Signed-off-by: Stefan Christ <s.christ-guT5V/WYfQezQB+pC5nmwQ@public.gmane.org>
Signed-off-by: Christoph Fritz <chf.fritz-gM/Ye1E23mwN+BqQ9rBEUg@public.gmane.org>
Signed-off-by: Stefan Riedmueller <s.riedmueller-guT5V/WYfQezQB+pC5nmwQ@public.gmane.org>
Reviewed-by: Fabio Estevam <fabio.estevam-3arQi8VN3Tc@public.gmane.org>
---
 arch/arm/boot/dts/imx6qdl-phytec-phycore-som.dtsi | 279 ++++++++++++++++++++++
 1 file changed, 279 insertions(+)
 create mode 100644 arch/arm/boot/dts/imx6qdl-phytec-phycore-som.dtsi

diff --git a/arch/arm/boot/dts/imx6qdl-phytec-phycore-som.dtsi b/arch/arm/boot/dts/imx6qdl-phytec-phycore-som.dtsi
new file mode 100644
index 0000000..6486df3
--- /dev/null
+++ b/arch/arm/boot/dts/imx6qdl-phytec-phycore-som.dtsi
@@ -0,0 +1,279 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Copyright (C) 2018 PHYTEC Messtechnik GmbH
+ * Author: Christian Hemp <c.hemp-guT5V/WYfQezQB+pC5nmwQ@public.gmane.org>
+ */
+
+#include <dt-bindings/gpio/gpio.h>
+
+/ {
+	aliases {
+		rtc1 = &da9062_rtc;
+		rtc2 = &snvs_rtc;
+	};
+
+	/*
+	 * Set the minimum memory size here and
+	 * let the bootloader set the real size.
+	 */
+	memory@10000000 {
+		device_type = "memory";
+		reg = <0x10000000 0x8000000>;
+	};
+
+	gpio_leds_som: somleds {
+		compatible = "gpio-leds";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_gpioleds_som>;
+
+		som-led-green {
+			label = "phycore:green";
+			gpios = <&gpio1 4 GPIO_ACTIVE_HIGH>;
+			linux,default-trigger = "heartbeat";
+		};
+	};
+};
+
+&ecspi1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_ecspi1>;
+	cs-gpios = <&gpio3 19 GPIO_ACTIVE_LOW>;
+	status = "okay";
+
+	m25p80: flash@0 {
+		compatible = "jedec,spi-nor";
+		spi-max-frequency = <20000000>;
+		reg = <0>;
+		status = "disabled";
+	};
+};
+
+&fec {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_enet>;
+	phy-handle = <&ethphy>;
+	phy-mode = "rgmii";
+	phy-supply = <&vdd_eth_io>;
+	phy-reset-gpios = <&gpio1 14 GPIO_ACTIVE_LOW>;
+	status = "disabled";
+
+	mdio {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		ethphy: ethernet-phy@3 {
+			reg = <3>;
+			txc-skew-ps = <1680>;
+			rxc-skew-ps = <1860>;
+		};
+	};
+};
+
+&gpmi {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_gpmi_nand>;
+	nand-on-flash-bbt;
+	status = "disabled";
+};
+
+&i2c3 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_i2c3>;
+	clock-frequency = <400000>;
+	status = "okay";
+
+	eeprom@50 {
+		compatible = "atmel,24c32";
+		reg = <0x50>;
+	};
+
+	pmic@58 {
+		compatible = "dlg,da9062";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_pmic>;
+		reg = <0x58>;
+		interrupt-parent = <&gpio1>;
+		interrupts = <2 IRQ_TYPE_LEVEL_LOW>;
+		interrupt-controller;
+
+		da9062_rtc: rtc {
+			compatible = "dlg,da9062-rtc";
+		};
+
+		watchdog {
+			compatible = "dlg,da9062-watchdog";
+		};
+
+		regulators {
+			vdd_arm: buck1 {
+				regulator-name = "vdd_arm";
+				regulator-min-microvolt = <730000>;
+				regulator-max-microvolt = <1380000>;
+				regulator-always-on;
+			};
+
+			vdd_soc: buck2 {
+				regulator-name = "vdd_soc";
+				regulator-min-microvolt = <730000>;
+				regulator-max-microvolt = <1380000>;
+				regulator-always-on;
+			};
+
+			vdd_ddr3_1p5: buck3 {
+				regulator-name = "vdd_ddr3";
+				regulator-min-microvolt = <1500000>;
+				regulator-max-microvolt = <1500000>;
+				regulator-always-on;
+			};
+
+			vdd_eth_1p2: buck4 {
+				regulator-name = "vdd_eth";
+				regulator-min-microvolt = <1200000>;
+				regulator-max-microvolt = <1200000>;
+				regulator-always-on;
+			};
+
+			vdd_snvs: ldo1 {
+				regulator-name = "vdd_snvs";
+				regulator-min-microvolt = <3000000>;
+				regulator-max-microvolt = <3000000>;
+				regulator-always-on;
+			};
+
+			vdd_high: ldo2 {
+				regulator-name = "vdd_high";
+				regulator-min-microvolt = <3000000>;
+				regulator-max-microvolt = <3000000>;
+				regulator-always-on;
+			};
+
+			vdd_eth_io: ldo3 {
+				regulator-name = "vdd_eth_io";
+				regulator-min-microvolt = <2500000>;
+				regulator-max-microvolt = <2500000>;
+			};
+
+			vdd_emmc_1p8: ldo4 {
+				regulator-name = "vdd_emmc";
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <1800000>;
+			};
+		};
+	};
+};
+
+&reg_arm {
+	vin-supply = <&vdd_arm>;
+};
+
+&reg_pu {
+	vin-supply = <&vdd_soc>;
+};
+
+&reg_soc {
+	vin-supply = <&vdd_soc>;
+};
+
+&snvs_poweroff {
+	status = "okay";
+};
+
+&usdhc4 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_usdhc4>;
+	bus-width = <8>;
+	non-removable;
+	vmmc-supply = <&vdd_emmc_1p8>;
+	status = "disabled";
+};
+
+&iomuxc {
+	pinctrl_enet: enetgrp {
+		fsl,pins = <
+			MX6QDL_PAD_ENET_MDIO__ENET_MDIO		0x1b0b0
+			MX6QDL_PAD_ENET_MDC__ENET_MDC		0x1b0b0
+			MX6QDL_PAD_RGMII_TXC__RGMII_TXC		0x1b0b0
+			MX6QDL_PAD_RGMII_TD0__RGMII_TD0		0x1b0b0
+			MX6QDL_PAD_RGMII_TD1__RGMII_TD1		0x1b0b0
+			MX6QDL_PAD_RGMII_TD2__RGMII_TD2		0x1b0b0
+			MX6QDL_PAD_RGMII_TD3__RGMII_TD3		0x1b0b0
+			MX6QDL_PAD_RGMII_TX_CTL__RGMII_TX_CTL	0x1b0b0
+			MX6QDL_PAD_ENET_REF_CLK__ENET_TX_CLK	0x1b0b0
+			MX6QDL_PAD_RGMII_RXC__RGMII_RXC		0x1b0b0
+			MX6QDL_PAD_RGMII_RD0__RGMII_RD0		0x1b0b0
+			MX6QDL_PAD_RGMII_RD1__RGMII_RD1		0x1b0b0
+			MX6QDL_PAD_RGMII_RD2__RGMII_RD2		0x1b0b0
+			MX6QDL_PAD_RGMII_RD3__RGMII_RD3		0x1b0b0
+			MX6QDL_PAD_RGMII_RX_CTL__RGMII_RX_CTL	0x1b0b0
+			MX6QDL_PAD_ENET_TX_EN__ENET_TX_EN	0x1b0b0
+			MX6QDL_PAD_SD2_DAT1__GPIO1_IO14		0x1b0b0
+		>;
+	};
+
+	pinctrl_gpioleds_som: gpioledssomgrp {
+		fsl,pins = <
+			MX6QDL_PAD_GPIO_4__GPIO1_IO04		0x1b0b0
+		>;
+	};
+
+	pinctrl_gpmi_nand: gpminandgrp {
+		fsl,pins = <
+			MX6QDL_PAD_NANDF_CLE__NAND_CLE		0xb0b1
+			MX6QDL_PAD_NANDF_ALE__NAND_ALE		0xb0b1
+			MX6QDL_PAD_NANDF_WP_B__NAND_WP_B	0xb0b1
+			MX6QDL_PAD_NANDF_RB0__NAND_READY_B	0xb000
+			MX6QDL_PAD_NANDF_CS0__NAND_CE0_B	0xb0b1
+			MX6QDL_PAD_NANDF_CS1__NAND_CE1_B	0xb0b1
+			MX6QDL_PAD_NANDF_CS2__NAND_CE2_B	0xb0b1
+			MX6QDL_PAD_NANDF_CS3__NAND_CE3_B	0xb0b1
+			MX6QDL_PAD_SD4_CMD__NAND_RE_B		0xb0b1
+			MX6QDL_PAD_SD4_CLK__NAND_WE_B		0xb0b1
+			MX6QDL_PAD_NANDF_D0__NAND_DATA00	0xb0b1
+			MX6QDL_PAD_NANDF_D1__NAND_DATA01	0xb0b1
+			MX6QDL_PAD_NANDF_D2__NAND_DATA02	0xb0b1
+			MX6QDL_PAD_NANDF_D3__NAND_DATA03	0xb0b1
+			MX6QDL_PAD_NANDF_D4__NAND_DATA04	0xb0b1
+			MX6QDL_PAD_NANDF_D5__NAND_DATA05	0xb0b1
+			MX6QDL_PAD_NANDF_D6__NAND_DATA06	0xb0b1
+			MX6QDL_PAD_NANDF_D7__NAND_DATA07	0xb0b1
+			MX6QDL_PAD_SD4_DAT0__NAND_DQS		0x00b1
+		>;
+	};
+
+	pinctrl_i2c3: i2c3grp {
+		fsl,pins = <
+			MX6QDL_PAD_GPIO_6__I2C3_SDA		0x4001b8b1
+			MX6QDL_PAD_GPIO_5__I2C3_SCL		0x4001b8b1
+		>;
+	};
+
+	pinctrl_ecspi1: ecspi1grp {
+		fsl,pins = <
+			MX6QDL_PAD_EIM_D16__ECSPI1_SCLK		0x100b1
+			MX6QDL_PAD_EIM_D17__ECSPI1_MISO		0x100b1
+			MX6QDL_PAD_EIM_D18__ECSPI1_MOSI		0x100b1
+			MX6QDL_PAD_EIM_D19__GPIO3_IO19		0x1b0b0
+		>;
+	};
+
+	pinctrl_pmic: pmicgrp {
+		fsl,pins = <
+			MX6QDL_PAD_GPIO_2__GPIO1_IO02		0x1b0b0
+		>;
+	};
+
+	pinctrl_usdhc4: usdhc4grp {
+		fsl,pins = <
+			MX6QDL_PAD_SD4_CMD__SD4_CMD		0x17059
+			MX6QDL_PAD_SD4_CLK__SD4_CLK		0x10059
+			MX6QDL_PAD_SD4_DAT0__SD4_DATA0		0x17059
+			MX6QDL_PAD_SD4_DAT1__SD4_DATA1		0x17059
+			MX6QDL_PAD_SD4_DAT2__SD4_DATA2		0x17059
+			MX6QDL_PAD_SD4_DAT3__SD4_DATA3		0x17059
+			MX6QDL_PAD_SD4_DAT4__SD4_DATA4		0x17059
+			MX6QDL_PAD_SD4_DAT5__SD4_DATA5		0x17059
+			MX6QDL_PAD_SD4_DAT6__SD4_DATA6		0x17059
+			MX6QDL_PAD_SD4_DAT7__SD4_DATA7		0x17059
+		>;
+	};
+};
-- 
2.7.4

--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at  http://vger.kernel.org/majordomo-info.html

[PATCH v5 2/6] ARM: dts: imx6: Add initial support for phyBOARD-Mira

[Stefan Riedmueller]

This patch adds basic support for PHYTEC phyBOARD-Mira as carrier board
for PHYTEC phyCORE-i.MX 6.

Signed-off-by: Christian Hemp <c.hemp-guT5V/WYfQezQB+pC5nmwQ@public.gmane.org>
Signed-off-by: Stefan Christ <s.christ-guT5V/WYfQezQB+pC5nmwQ@public.gmane.org>
Signed-off-by: Christoph Fritz <chf.fritz-gM/Ye1E23mwN+BqQ9rBEUg@public.gmane.org>
Signed-off-by: Stefan Riedmueller <s.riedmueller-guT5V/WYfQezQB+pC5nmwQ@public.gmane.org>
Reviewed-by: Fabio Estevam <fabio.estevam-3arQi8VN3Tc@public.gmane.org>
---
 arch/arm/boot/dts/imx6qdl-phytec-mira.dtsi | 390 +++++++++++++++++++++++++++++
 1 file changed, 390 insertions(+)
 create mode 100644 arch/arm/boot/dts/imx6qdl-phytec-mira.dtsi

diff --git a/arch/arm/boot/dts/imx6qdl-phytec-mira.dtsi b/arch/arm/boot/dts/imx6qdl-phytec-mira.dtsi
new file mode 100644
index 0000000..9ebd438
--- /dev/null
+++ b/arch/arm/boot/dts/imx6qdl-phytec-mira.dtsi
@@ -0,0 +1,390 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Copyright (C) 2018 PHYTEC Messtechnik GmbH
+ * Author: Christian Hemp <c.hemp-guT5V/WYfQezQB+pC5nmwQ@public.gmane.org>
+ */
+
+
+/ {
+	aliases {
+		rtc0 = &i2c_rtc;
+	};
+
+	backlight: backlight {
+		compatible = "pwm-backlight";
+		brightness-levels = <0 4 8 16 32 64 128 255>;
+		default-brightness-level = <7>;
+		power-supply = <&reg_backlight>;
+		pwms = <&pwm1 0 5000000>;
+		status = "okay";
+	};
+
+	gpio_leds: leds {
+		compatible = "gpio-leds";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_gpioleds>;
+		status = "disabled";
+
+		red {
+			label = "phyboard-mira:red";
+			gpios = <&gpio5 22 GPIO_ACTIVE_HIGH>;
+		};
+
+		green {
+			label = "phyboard-mira:green";
+			gpios = <&gpio5 23 GPIO_ACTIVE_HIGH>;
+		};
+
+		blue {
+			label = "phyboard-mira:blue";
+			gpios = <&gpio5 24 GPIO_ACTIVE_HIGH>;
+			linux,default-trigger = "mmc0";
+		};
+	};
+
+	reg_backlight: regulator-backlight {
+		compatible = "regulator-fixed";
+		regulator-name = "backlight_3v3";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		regulator-always-on;
+	};
+
+	reg_en_switch: regulator-en-switch {
+		compatible = "regulator-fixed";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_en_switch>;
+		regulator-name = "Enable Switch";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		enable-active-high;
+		gpio = <&gpio3 4 GPIO_ACTIVE_HIGH>;
+		regulator-always-on;
+	};
+
+	reg_flexcan1: regulator-flexcan1 {
+		compatible = "regulator-fixed";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_flexcan1_en>;
+		regulator-name = "flexcan1-reg";
+		regulator-min-microvolt = <1500000>;
+		regulator-max-microvolt = <1500000>;
+		gpio = <&gpio2 20 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+	};
+
+	reg_panel: regulator-panel {
+		compatible = "regulator-fixed";
+		regulator-name = "panel-power-supply";
+		regulator-min-microvolt = <12000000>;
+		regulator-max-microvolt = <12000000>;
+		regulator-always-on;
+	};
+
+	reg_pcie: regulator-pcie {
+		compatible = "regulator-fixed";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_pcie_reg>;
+		regulator-name = "mPCIe_1V5";
+		regulator-min-microvolt = <1500000>;
+		regulator-max-microvolt = <1500000>;
+		gpio = <&gpio3 0 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+	};
+
+	reg_usb_h1_vbus: usb-h1-vbus {
+		compatible = "regulator-fixed";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_usbh1_vbus>;
+		regulator-name = "usb_h1_vbus";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		gpio = <&gpio2 18 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+	};
+
+	reg_usbotg_vbus: usbotg-vbus {
+		compatible = "regulator-fixed";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_usbotg_vbus>;
+		regulator-name = "usb_otg_vbus";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		gpio = <&gpio2 19 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+	};
+
+	panel {
+		compatible = "auo,g104sn02";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_panel_en>;
+		power-supply = <&reg_panel>;
+		enable-gpios = <&gpio2 28 GPIO_ACTIVE_LOW>;
+		backlight = <&backlight>;
+
+		port {
+			panel_in: endpoint {
+				remote-endpoint = <&lvds0_out>;
+			};
+		};
+	};
+};
+
+&can1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_flexcan1>;
+	xceiver-supply = <&reg_flexcan1>;
+	status = "disabled";
+};
+
+&hdmi {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_hdmicec>;
+	ddc-i2c-bus = <&i2c2>;
+	status = "disabled";
+};
+
+&i2c1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_i2c1>;
+	clock-frequency = <400000>;
+	status = "disabled";
+
+	stmpe: touchctrl@44 {
+		compatible = "st,stmpe811";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_stmpe>;
+		reg = <0x44>;
+		interrupt-parent = <&gpio7>;
+		interrupts = <12 IRQ_TYPE_NONE>;
+		status = "disabled";
+
+		stmpe_touchscreen {
+			compatible = "st,stmpe-ts";
+			st,sample-time = <4>;
+			st,mod-12b = <1>;
+			st,ref-sel = <0>;
+			st,adc-freq = <1>;
+			st,ave-ctrl = <1>;
+			st,touch-det-delay = <2>;
+			st,settling = <2>;
+			st,fraction-z = <7>;
+			st,i-drive = <1>;
+		};
+	};
+
+	i2c_rtc: rtc@68 {
+		compatible = "microcrystal,rv4162";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_rtc_int>;
+		reg = <0x68>;
+		interrupt-parent = <&gpio7>;
+		interrupts = <8 IRQ_TYPE_LEVEL_HIGH>;
+		status = "disabled";
+	};
+};
+
+&i2c2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_i2c2>;
+	clock-frequency = <100000>;
+	status = "disabled";
+};
+
+&ldb {
+	status = "okay";
+
+	lvds-channel@0 {
+		fsl,data-mapping = "spwg";
+		fsl,data-width = <24>;
+		status = "disabled";
+
+		port@4 {
+			reg = <4>;
+
+			lvds0_out: endpoint {
+				remote-endpoint = <&panel_in>;
+			};
+		};
+	};
+};
+
+&pcie {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_pcie>;
+	reset-gpio = <&gpio2 25 GPIO_ACTIVE_LOW>;
+	vpcie-supply = <&reg_pcie>;
+	status = "disabled";
+};
+
+&pwm1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_pwm1>;
+	status = "okay";
+};
+
+&uart2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_uart2>;
+	status = "okay";
+};
+
+&uart3 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_uart3>;
+	uart-has-rtscts;
+	status = "disabled";
+};
+
+&usbh1 {
+	vbus-supply = <&reg_usb_h1_vbus>;
+	disable-over-current;
+	status = "disabled";
+};
+
+&usbotg {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_usbotg>;
+	vbus-supply = <&reg_usbotg_vbus>;
+	disable-over-current;
+	status = "disabled";
+};
+
+&usdhc1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_usdhc1>;
+	cd-gpios = <&gpio6 31 GPIO_ACTIVE_LOW>;
+	no-1-8-v;
+	status = "disabled";
+};
+
+&iomuxc {
+	pinctrl_panel_en: panelen1grp {
+		fsl,pins = <
+			MX6QDL_PAD_EIM_EB0__GPIO2_IO28		0xb0b1
+		>;
+	};
+
+	pinctrl_en_switch: enswitchgrp {
+		fsl,pins = <
+			MX6QDL_PAD_EIM_DA4__GPIO3_IO04		0xb0b1
+		>;
+	};
+
+	pinctrl_flexcan1: flexcan1grp {
+		fsl,pins = <
+			MX6QDL_PAD_GPIO_7__FLEXCAN1_TX		0x1b0b0
+			MX6QDL_PAD_GPIO_8__FLEXCAN1_RX		0x1b0b0
+		>;
+	};
+
+	pinctrl_flexcan1_en: flexcan1engrp {
+		fsl,pins = <
+			MX6QDL_PAD_EIM_A18__GPIO2_IO20		0xb0b1
+		>;
+	};
+
+	pinctrl_gpioleds: gpioledsgrp {
+		fsl,pins = <
+			MX6QDL_PAD_CSI0_DAT4__GPIO5_IO22	0x1b0b0
+			MX6QDL_PAD_CSI0_DAT5__GPIO5_IO23	0x1b0b0
+			MX6QDL_PAD_CSI0_DAT6__GPIO5_IO24	0x1b0b0
+		>;
+	};
+
+	pinctrl_hdmicec: hdmicecgrp {
+		fsl,pins = <
+			MX6QDL_PAD_KEY_ROW2__HDMI_TX_CEC_LINE	0x1f8b0
+		>;
+	};
+
+	pinctrl_i2c2: i2c2grp {
+		fsl,pins = <
+			MX6QDL_PAD_KEY_ROW3__I2C2_SDA		0x4001b8b1
+			MX6QDL_PAD_KEY_COL3__I2C2_SCL		0x4001b8b1
+		>;
+	};
+
+	pinctrl_i2c1: i2c1grp {
+		fsl,pins = <
+			MX6QDL_PAD_EIM_D21__I2C1_SCL		0x4001b8b1
+			MX6QDL_PAD_EIM_D28__I2C1_SDA		0x4001b8b1
+		>;
+	};
+
+	pinctrl_pcie: pciegrp {
+		fsl,pins = <
+			MX6QDL_PAD_EIM_OE__GPIO2_IO25		0xb0b1
+		>;
+	};
+
+	pinctrl_pcie_reg: pciereggrp {
+		fsl,pins = <
+			MX6QDL_PAD_EIM_DA0__GPIO3_IO00		0xb0b1
+		>;
+	};
+
+	pinctrl_pwm1: pwm1grp {
+		fsl,pins = <
+			MX6QDL_PAD_GPIO_9__PWM1_OUT		0x1b0b1
+		>;
+	};
+
+	pinctrl_rtc_int: rtcintgrp {
+		fsl,pins = <
+			MX6QDL_PAD_SD3_RST__GPIO7_IO08		0x1b0b0
+		>;
+	};
+
+	pinctrl_stmpe: stmpegrp {
+		fsl,pins = <
+			MX6QDL_PAD_GPIO_17__GPIO7_IO12		0x1b0b0
+		>;
+	};
+
+	pinctrl_uart2: uart2grp {
+		fsl,pins = <
+			MX6QDL_PAD_EIM_D26__UART2_TX_DATA	0x1b0b1
+			MX6QDL_PAD_EIM_D27__UART2_RX_DATA	0x1b0b1
+		>;
+	};
+
+	pinctrl_uart3: uart3grp {
+		fsl,pins = <
+			MX6QDL_PAD_EIM_EB3__UART3_CTS_B		0x1b0b1
+			MX6QDL_PAD_EIM_D23__UART3_RTS_B		0x1b0b1
+			MX6QDL_PAD_EIM_D24__UART3_TX_DATA	0x1b0b1
+			MX6QDL_PAD_EIM_D25__UART3_RX_DATA	0x1b0b1
+		>;
+	};
+
+	pinctrl_usbh1_vbus: usbh1vbusgrp {
+		fsl,pins = <
+			MX6QDL_PAD_EIM_A20__GPIO2_IO18		0xb0b1
+		>;
+	};
+
+	pinctrl_usbotg: usbotggrp {
+		fsl,pins = <
+			MX6QDL_PAD_GPIO_1__USB_OTG_ID		0x17059
+		>;
+	};
+
+	pinctrl_usbotg_vbus: usbotgvbusgrp {
+		fsl,pins = <
+			MX6QDL_PAD_EIM_A19__GPIO2_IO19		0xb0b1
+		>;
+	};
+
+	pinctrl_usdhc1: usdhc1grp {
+		fsl,pins = <
+			MX6QDL_PAD_SD1_CMD__SD1_CMD		0x170f9
+			MX6QDL_PAD_SD1_CLK__SD1_CLK		0x100f9
+			MX6QDL_PAD_SD1_DAT0__SD1_DATA0		0x170f9
+			MX6QDL_PAD_SD1_DAT1__SD1_DATA1		0x170f9
+			MX6QDL_PAD_SD1_DAT2__SD1_DATA2		0x170f9
+			MX6QDL_PAD_SD1_DAT3__SD1_DATA3		0x170f9
+			MX6QDL_PAD_EIM_BCLK__GPIO6_IO31		0xb0b1  /* CD */
+		>;
+	};
+};
-- 
2.7.4

--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at  http://vger.kernel.org/majordomo-info.html

[PATCH v5 3/6] ARM: dts: imx6: Add support for phyBOARD-Mira i.MX 6Quad/Dual RDK

[Stefan Riedmueller]

From: Christian Hemp <c.hemp-guT5V/WYfQezQB+pC5nmwQ@public.gmane.org>

Add support for the PHYTEC phyBOARD-Mira Rapid Development Kit with
i.MX 6Quad/Dual with eMMC or NAND.

Following interfaces are supported:
- Gigabit Ethernet
- USB Host
- CAN
- RS232
- PCIe
- LVDS
- HDMI

Signed-off-by: Christian Hemp <c.hemp-guT5V/WYfQezQB+pC5nmwQ@public.gmane.org>
Signed-off-by: Stefan Christ <s.christ-guT5V/WYfQezQB+pC5nmwQ@public.gmane.org>
Signed-off-by: Stefan Riedmueller <s.riedmueller-guT5V/WYfQezQB+pC5nmwQ@public.gmane.org>
Reviewed-by: Fabio Estevam <fabio.estevam-3arQi8VN3Tc@public.gmane.org>
---
 arch/arm/boot/dts/Makefile                       |  2 +
 arch/arm/boot/dts/imx6q-phytec-mira-rdk-emmc.dts | 72 ++++++++++++++++++++++++
 arch/arm/boot/dts/imx6q-phytec-mira-rdk-nand.dts | 72 ++++++++++++++++++++++++
 3 files changed, 146 insertions(+)
 create mode 100644 arch/arm/boot/dts/imx6q-phytec-mira-rdk-emmc.dts
 create mode 100644 arch/arm/boot/dts/imx6q-phytec-mira-rdk-nand.dts

diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
index d0381e9..b793617 100644
--- a/arch/arm/boot/dts/Makefile
+++ b/arch/arm/boot/dts/Makefile
@@ -449,6 +449,8 @@ dtb-$(CONFIG_SOC_IMX6Q) += \
 	imx6q-nitrogen6_max.dtb \
 	imx6q-nitrogen6_som2.dtb \
 	imx6q-novena.dtb \
+	imx6q-phytec-mira-rdk-emmc.dtb \
+	imx6q-phytec-mira-rdk-nand.dtb \
 	imx6q-phytec-pbab01.dtb \
 	imx6q-pistachio.dtb \
 	imx6q-rex-pro.dtb \
diff --git a/arch/arm/boot/dts/imx6q-phytec-mira-rdk-emmc.dts b/arch/arm/boot/dts/imx6q-phytec-mira-rdk-emmc.dts
new file mode 100644
index 0000000..8fdce3c
--- /dev/null
+++ b/arch/arm/boot/dts/imx6q-phytec-mira-rdk-emmc.dts
@@ -0,0 +1,72 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Copyright (C) 2018 PHYTEC Messtechnik GmbH
+ * Author: Christian Hemp <c.hemp-guT5V/WYfQezQB+pC5nmwQ@public.gmane.org>
+ */
+
+/dts-v1/;
+#include "imx6q.dtsi"
+#include "imx6qdl-phytec-phycore-som.dtsi"
+#include "imx6qdl-phytec-mira.dtsi"
+
+/ {
+	model = "PHYTEC phyBOARD-Mira Quad Carrier-Board with eMMC";
+	compatible = "phytec,imx6q-pbac06-emmc", "phytec,imx6q-pbac06",
+		     "phytec,imx6qdl-pcm058", "fsl,imx6q";
+
+	chosen {
+		linux,stdout-path = &uart2;
+	};
+};
+
+&can1 {
+	status = "okay";
+};
+
+&fec {
+	status = "okay";
+};
+
+&hdmi {
+	status = "okay";
+};
+
+&i2c1 {
+	status = "okay";
+};
+
+&i2c2 {
+	status = "okay";
+};
+
+&i2c_rtc {
+	status = "okay";
+};
+
+&m25p80 {
+	status = "okay";
+};
+
+&pcie {
+	status = "okay";
+};
+
+&uart3 {
+	status = "okay";
+};
+
+&usbh1 {
+	status = "okay";
+};
+
+&usbotg {
+	status = "okay";
+};
+
+&usdhc1 {
+	status = "okay";
+};
+
+&usdhc4 {
+	status = "okay";
+};
diff --git a/arch/arm/boot/dts/imx6q-phytec-mira-rdk-nand.dts b/arch/arm/boot/dts/imx6q-phytec-mira-rdk-nand.dts
new file mode 100644
index 0000000..8afa5ce
--- /dev/null
+++ b/arch/arm/boot/dts/imx6q-phytec-mira-rdk-nand.dts
@@ -0,0 +1,72 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Copyright (C) 2018 PHYTEC Messtechnik GmbH
+ * Author: Christian Hemp <c.hemp-guT5V/WYfQezQB+pC5nmwQ@public.gmane.org>
+ */
+
+/dts-v1/;
+#include "imx6q.dtsi"
+#include "imx6qdl-phytec-phycore-som.dtsi"
+#include "imx6qdl-phytec-mira.dtsi"
+
+/ {
+	model = "PHYTEC phyBOARD-Mira Quad Carrier-Board with NAND";
+	compatible = "phytec,imx6q-pbac06-nand", "phytec,imx6q-pbac06",
+		     "phytec,imx6qdl-pcm058", "fsl,imx6q";
+
+	chosen {
+		linux,stdout-path = &uart2;
+	};
+};
+
+&can1 {
+	status = "okay";
+};
+
+&fec {
+	status = "okay";
+};
+
+&gpmi {
+	status = "okay";
+};
+
+&hdmi {
+	status = "okay";
+};
+
+&i2c1 {
+	status = "okay";
+};
+
+&i2c2 {
+	status = "okay";
+};
+
+&i2c_rtc {
+	status = "okay";
+};
+
+&m25p80 {
+	status = "okay";
+};
+
+&pcie {
+	status = "okay";
+};
+
+&uart3 {
+	status = "okay";
+};
+
+&usbh1 {
+	status = "okay";
+};
+
+&usbotg {
+	status = "okay";
+};
+
+&usdhc1 {
+	status = "okay";
+};
-- 
2.7.4

--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at  http://vger.kernel.org/majordomo-info.html

[PATCH v5 4/6] ARM: dts: imx6: Add support for phyBOARD-Mira i.MX 6 DualLight/Solo RDK

[Stefan Riedmueller]

From: Christian Hemp <c.hemp-guT5V/WYfQezQB+pC5nmwQ@public.gmane.org>

Add support for the PHYTEC phyBOARD-Mira Low-Cost Rapid Development Kit
with i.MX 6DualLight/Solo with NAND.

Following interfaces are supported:
- 100 MBit Ethernet
- USB Host
- RS232
- HDMI

Signed-off-by: Christian Hemp <c.hemp-guT5V/WYfQezQB+pC5nmwQ@public.gmane.org>
Signed-off-by: Stefan Christ <s.christ-guT5V/WYfQezQB+pC5nmwQ@public.gmane.org>
Signed-off-by: Stefan Riedmueller <s.riedmueller-guT5V/WYfQezQB+pC5nmwQ@public.gmane.org>
Reviewed-by: Fabio Estevam <fabio.estevam-3arQi8VN3Tc@public.gmane.org>
---
 arch/arm/boot/dts/Makefile                        |  1 +
 arch/arm/boot/dts/imx6dl-phytec-mira-rdk-nand.dts | 64 +++++++++++++++++++++++
 2 files changed, 65 insertions(+)
 create mode 100644 arch/arm/boot/dts/imx6dl-phytec-mira-rdk-nand.dts

diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
index b793617..07d99a1 100644
--- a/arch/arm/boot/dts/Makefile
+++ b/arch/arm/boot/dts/Makefile
@@ -388,6 +388,7 @@ dtb-$(CONFIG_SOC_IMX6Q) += \
 	imx6dl-icore-rqs.dtb \
 	imx6dl-nit6xlite.dtb \
 	imx6dl-nitrogen6x.dtb \
+	imx6dl-phytec-mira-rdk-nand.dtb \
 	imx6dl-phytec-pbab01.dtb \
 	imx6dl-rex-basic.dtb \
 	imx6dl-riotboard.dtb \
diff --git a/arch/arm/boot/dts/imx6dl-phytec-mira-rdk-nand.dts b/arch/arm/boot/dts/imx6dl-phytec-mira-rdk-nand.dts
new file mode 100644
index 0000000..a8adcb2
--- /dev/null
+++ b/arch/arm/boot/dts/imx6dl-phytec-mira-rdk-nand.dts
@@ -0,0 +1,64 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Copyright (C) 2018 PHYTEC Messtechnik GmbH
+ * Author: Christian Hemp <c.hemp-guT5V/WYfQezQB+pC5nmwQ@public.gmane.org>
+ */
+
+/dts-v1/;
+#include "imx6dl.dtsi"
+#include "imx6qdl-phytec-phycore-som.dtsi"
+#include "imx6qdl-phytec-mira.dtsi"
+
+/ {
+	model = "PHYTEC phyBOARD-Mira DualLite/Solo Carrier-Board with NAND";
+	compatible = "phytec,imx6dl-pbac06-nand", "phytec,imx6dl-pbac06",
+		     "phytec,imx6qdl-pcm058", "fsl,imx6dl";
+
+	chosen {
+		linux,stdout-path = &uart2;
+	};
+};
+
+&ethphy {
+	max-speed = <100>;
+};
+
+&fec {
+	status = "okay";
+};
+
+&gpmi {
+	status = "okay";
+};
+
+&hdmi {
+	status = "okay";
+};
+
+&i2c1 {
+	status = "okay";
+};
+
+&i2c2 {
+	status = "okay";
+};
+
+&i2c_rtc {
+	status = "okay";
+};
+
+&uart3 {
+	status = "okay";
+};
+
+&usbh1 {
+	status = "okay";
+};
+
+&usbotg {
+	status = "okay";
+};
+
+&usdhc1 {
+	status = "okay";
+};
-- 
2.7.4

--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at  http://vger.kernel.org/majordomo-info.html

[PATCH v5 5/6] ARM: dts: imx6: Add support for phyBOARD-Mira with i.MX 6QuadPlus

[Stefan Riedmueller]

From: Enrico Scholz <enrico.scholz-wttK6gPy29v+Hn7q9Vec/7NAH6kLmebB@public.gmane.org>

Add support for the PHYTEC phyBOARD-Mira with i.MX 6QuadPlus with NAND.
It is based on the phyBOARD-Mira with i.MX 6Quad/Dual and supports the
same interfaces.

Signed-off-by: Enrico Scholz <enrico.scholz-wttK6gPy29v+Hn7q9Vec/7NAH6kLmebB@public.gmane.org>
Signed-off-by: Stefan Lengfeld <s.lengfeld-guT5V/WYfQezQB+pC5nmwQ@public.gmane.org>
Signed-off-by: Christian Hemp <c.hemp-guT5V/WYfQezQB+pC5nmwQ@public.gmane.org>
Signed-off-by: Stefan Riedmueller <s.riedmueller-guT5V/WYfQezQB+pC5nmwQ@public.gmane.org>
Reviewed-by: Fabio Estevam <fabio.estevam-3arQi8VN3Tc@public.gmane.org>
---
 arch/arm/boot/dts/Makefile                        |  1 +
 arch/arm/boot/dts/imx6qp-phytec-mira-rdk-nand.dts | 72 +++++++++++++++++++++++
 2 files changed, 73 insertions(+)
 create mode 100644 arch/arm/boot/dts/imx6qp-phytec-mira-rdk-nand.dts

diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
index 07d99a1..d42b522 100644
--- a/arch/arm/boot/dts/Makefile
+++ b/arch/arm/boot/dts/Makefile
@@ -479,6 +479,7 @@ dtb-$(CONFIG_SOC_IMX6Q) += \
 	imx6q-zii-rdu2.dtb \
 	imx6qp-nitrogen6_max.dtb \
 	imx6qp-nitrogen6_som2.dtb \
+	imx6qp-phytec-mira-rdk-nand.dtb \
 	imx6qp-sabreauto.dtb \
 	imx6qp-sabresd.dtb \
 	imx6qp-tx6qp-8037.dtb \
diff --git a/arch/arm/boot/dts/imx6qp-phytec-mira-rdk-nand.dts b/arch/arm/boot/dts/imx6qp-phytec-mira-rdk-nand.dts
new file mode 100644
index 0000000..3618e53
--- /dev/null
+++ b/arch/arm/boot/dts/imx6qp-phytec-mira-rdk-nand.dts
@@ -0,0 +1,72 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Copyright (C) 2018 PHYTEC Messtechnik GmbH
+ * Author: Enrico Scholz <enrico.scholz-wttK6gPy29v+Hn7q9Vec/7NAH6kLmebB@public.gmane.org>
+ */
+
+/dts-v1/;
+#include "imx6qp.dtsi"
+#include "imx6qdl-phytec-phycore-som.dtsi"
+#include "imx6qdl-phytec-mira.dtsi"
+
+/ {
+	model = "PHYTEC phyBOARD-Mira QuadPlus Carrier-Board with NAND";
+	compatible = "phytec,imx6qp-pbac06-nand", "phytec,imx6qp-pbac06",
+		     "phytec,imx6qdl-pcm058", "fsl,imx6qp";
+
+	chosen {
+		linux,stdout-path = &uart2;
+	};
+};
+
+&can1 {
+	status = "okay";
+};
+
+&fec {
+	status = "okay";
+};
+
+&gpmi {
+	status = "okay";
+};
+
+&hdmi {
+	status = "okay";
+};
+
+&i2c1 {
+	status = "okay";
+};
+
+&i2c2 {
+	status = "okay";
+};
+
+&i2c_rtc {
+	status = "okay";
+};
+
+&m25p80 {
+	status = "okay";
+};
+
+&pcie {
+	status = "okay";
+};
+
+&uart3 {
+	status = "okay";
+};
+
+&usbh1 {
+	status = "okay";
+};
+
+&usbotg {
+	status = "okay";
+};
+
+&usdhc1 {
+	status = "okay";
+};
-- 
2.7.4

--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at  http://vger.kernel.org/majordomo-info.html

[PATCH v5 6/6] ARM: imx_v6_v7_defconfig: Enable Dialog Semiconductor DA9062 driver

[Stefan Riedmueller]

The phyCORE-i.MX 6 uses the DA9062/63 PMIC, RTC and Watchdog driver.

Enable these options by default.

Signed-off-by: Stefan Riedmueller <s.riedmueller-guT5V/WYfQezQB+pC5nmwQ@public.gmane.org>
Reviewed-by: Fabio Estevam <fabio.estevam-3arQi8VN3Tc@public.gmane.org>
---
 arch/arm/configs/imx_v6_v7_defconfig | 4 ++++
 1 file changed, 4 insertions(+)

diff --git a/arch/arm/configs/imx_v6_v7_defconfig b/arch/arm/configs/imx_v6_v7_defconfig
index 6726c83..e3c4163 100644
--- a/arch/arm/configs/imx_v6_v7_defconfig
+++ b/arch/arm/configs/imx_v6_v7_defconfig
@@ -216,8 +216,10 @@ CONFIG_THERMAL_WRITABLE_TRIPS=y
 CONFIG_CPU_THERMAL=y
 CONFIG_IMX_THERMAL=y
 CONFIG_WATCHDOG=y
+CONFIG_DA9062_WATCHDOG=y
 CONFIG_IMX2_WDT=y
 CONFIG_MFD_DA9052_I2C=y
+CONFIG_MFD_DA9062=y
 CONFIG_MFD_MC13XXX_SPI=y
 CONFIG_MFD_MC13XXX_I2C=y
 CONFIG_MFD_STMPE=y
@@ -225,6 +227,7 @@ CONFIG_REGULATOR=y
 CONFIG_REGULATOR_FIXED_VOLTAGE=y
 CONFIG_REGULATOR_ANATOP=y
 CONFIG_REGULATOR_DA9052=y
+CONFIG_REGULATOR_DA9062=y
 CONFIG_REGULATOR_GPIO=y
 CONFIG_REGULATOR_MC13783=y
 CONFIG_REGULATOR_MC13892=y
@@ -348,6 +351,7 @@ CONFIG_RTC_DRV_ISL1208=y
 CONFIG_RTC_DRV_PCF8523=y
 CONFIG_RTC_DRV_PCF8563=y
 CONFIG_RTC_DRV_M41T80=y
+CONFIG_RTC_DRV_DA9063=y
 CONFIG_RTC_DRV_MC13XXX=y
 CONFIG_RTC_DRV_MXC=y
 CONFIG_RTC_DRV_SNVS=y
-- 
2.7.4

--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at  http://vger.kernel.org/majordomo-info.html

Re: [PATCH v5 0/6] ARM: dts: Add PHYTEC phyCORE-i.MX 6 and phyBOARD-Mira carrier board support

[Stefan Riedmüller]

Hi Shawn,

I noticed this patch stack did not find its way into your next branch 
yet. Is there anything I can do to speed up the process?

Thanks,
Stefan

On 09.01.2018 17:09, Stefan Riedmueller wrote:
> This patchset adds support for the PHYTEC phyCORE-i.MX 6 and phyBOARD-Mira.
>
> Following boards are included:
> phyBOARD-Mira with phyCORE-i.MX 6 Quad/Dual with:
> - i.MX 6Quad/Dual SOC
> - NAND or eMMC
> - HDMI interface
> - LVDS display interface
> - Gigabit Ethernet
> - USB Host
> - CAN
> - RS232
> - PCIe
> This board also contains an LVDS camera interface and parallel display
> interface which are not yet supported.
>
> phyBAORD-Mira with phyCORE-i.MX 6 DualLight/Solo with:
> - i.MX 6DualLight/Solo
> - NAND
> - HDMI interface
> - 100 MBit/s Ethernet
> - USB Host
> - RS232
>
> phyBOARD-Mira with phyCORE-i.MX 6 QuadPlus with:
> - i.MX 6QuadPlus SOC
> - NAND
> - HDMI interface
> - LVDS display interface
> - Gigabit Ethernet
> - USB Host
> - CAN
> - RS232
> - PCIe
> This board also contains an LVDS camera interface and parallel display
> interface which are not yet supported.
>
> The entire series is based on v4.15-rc4.
>
> Changes since v1:
> - Removed unnecessary ipu aliases
> - Added unit-address to memory node name
> - Fixed eeprom compatible to correct vendor name (atmel instead of cat)
> - Fixed rtc compatible to correct vendor name (microcrystal instead of mc)
> - Changed pcie regulator to be used with vpcie-supply in &pcie node and
>    removed regulator-always-on
> - Changed pcie reset-gpio polarity to GPIO_ACTIVE_LOW
> - Replaced fsl,uart-has-rtscts by uart-has-rtscts
> - Fixed typos in defconfig patch
>
> Changes since v2:
> - Fixed typo in patch subject PATCH 4/6
> - Added reviewed by tags on PATCH 4/6 and PATCH 6/6
>
> Changes since v3:
> - Removed model and compatible from phycore dtsi
> - Changed flash compatible to jedec,spi-nor
> - Renamed some_green node to som-led-green
> - Dropped labels for eeprom, pmic, da9062_wdt and da9062_reg
> - Renamed flash label to m25p80
> - Put compatible at beginning of property lists
> - Changed copyright year to 2018
> - Added reviewed by tags on PATCH 1/6, 2/6, 3/6 and 5/6
>
> Changes since v4:
> - Rearranged &m25p80 node in dts files to fit alphabetical order
> - Fixed a parenthesis for uniformity in mira dtsi
>
> Christian Hemp (2):
>    ARM: dts: imx6: Add support for phyBOARD-Mira i.MX 6Quad/Dual RDK
>    ARM: dts: imx6: Add support for phyBOARD-Mira i.MX 6 DualLight/Solo
>      RDK
>
> Enrico Scholz (1):
>    ARM: dts: imx6: Add support for phyBOARD-Mira with i.MX 6QuadPlus
>
> Stefan Riedmueller (3):
>    ARM: dts: imx6: Add initial support for phyCORE-i.MX 6 SOM
>    ARM: dts: imx6: Add initial support for phyBOARD-Mira
>    ARM: imx_v6_v7_defconfig: Enable Dialog Semiconductor DA9062 driver
>
>   arch/arm/boot/dts/Makefile                        |   4 +
>   arch/arm/boot/dts/imx6dl-phytec-mira-rdk-nand.dts |  64 ++++
>   arch/arm/boot/dts/imx6q-phytec-mira-rdk-emmc.dts  |  72 ++++
>   arch/arm/boot/dts/imx6q-phytec-mira-rdk-nand.dts  |  72 ++++
>   arch/arm/boot/dts/imx6qdl-phytec-mira.dtsi        | 390 ++++++++++++++++++++++
>   arch/arm/boot/dts/imx6qdl-phytec-phycore-som.dtsi | 279 ++++++++++++++++
>   arch/arm/boot/dts/imx6qp-phytec-mira-rdk-nand.dts |  72 ++++
>   arch/arm/configs/imx_v6_v7_defconfig              |   4 +
>   8 files changed, 957 insertions(+)
>   create mode 100644 arch/arm/boot/dts/imx6dl-phytec-mira-rdk-nand.dts
>   create mode 100644 arch/arm/boot/dts/imx6q-phytec-mira-rdk-emmc.dts
>   create mode 100644 arch/arm/boot/dts/imx6q-phytec-mira-rdk-nand.dts
>   create mode 100644 arch/arm/boot/dts/imx6qdl-phytec-mira.dtsi
>   create mode 100644 arch/arm/boot/dts/imx6qdl-phytec-phycore-som.dtsi
>   create mode 100644 arch/arm/boot/dts/imx6qp-phytec-mira-rdk-nand.dts
>

--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at  http://vger.kernel.org/majordomo-info.html

Re: [PATCH v5 0/6] ARM: dts: Add PHYTEC phyCORE-i.MX 6 and phyBOARD-Mira carrier board support

[Shawn Guo]

On Tue, Jan 09, 2018 at 05:09:54PM +0100, Stefan Riedmueller wrote:
> Changes since v4:
> - Rearranged &m25p80 node in dts files to fit alphabetical order
> - Fixed a parenthesis for uniformity in mira dtsi
> 
> Christian Hemp (2):
>   ARM: dts: imx6: Add support for phyBOARD-Mira i.MX 6Quad/Dual RDK
>   ARM: dts: imx6: Add support for phyBOARD-Mira i.MX 6 DualLight/Solo
>     RDK
> 
> Enrico Scholz (1):
>   ARM: dts: imx6: Add support for phyBOARD-Mira with i.MX 6QuadPlus
> 
> Stefan Riedmueller (3):
>   ARM: dts: imx6: Add initial support for phyCORE-i.MX 6 SOM
>   ARM: dts: imx6: Add initial support for phyBOARD-Mira

Okay, I replaced v4 with this v5.

>   ARM: imx_v6_v7_defconfig: Enable Dialog Semiconductor DA9062 driver

This one still doesn't apply to imx/defconfig.  Please rebase and
resend.

Shawn
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at  http://vger.kernel.org/majordomo-info.html