From: Kalle Valo <kvalo@codeaurora.org>
To: linux-wireless@vger.kernel.org
Cc: ath11k@lists.infradead.org, devicetree@vger.kernel.org
Subject: [PATCH v2 01/49] dt: bindings: net: add qcom,ath11k.yaml
Date: Sun, 20 Oct 2019 13:03:19 +0300 [thread overview]
Message-ID: <1571565847-10338-2-git-send-email-kvalo@codeaurora.org> (raw)
In-Reply-To: <1571565847-10338-1-git-send-email-kvalo@codeaurora.org>
ath11k is a driver for Qualcomm IEEE 802.11ax devices. Add a
bindings document for the driver, first documenting IPQ8074 which is the
only device ath11k currently supports.
Signed-off-by: Anilkumar Kolli <akolli@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
---
.../bindings/net/wireless/qcom,ath11k.yaml | 277 +++++++++++++++++++++
1 file changed, 277 insertions(+)
diff --git a/Documentation/devicetree/bindings/net/wireless/qcom,ath11k.yaml b/Documentation/devicetree/bindings/net/wireless/qcom,ath11k.yaml
new file mode 100644
index 000000000000..5d25542f85f8
--- /dev/null
+++ b/Documentation/devicetree/bindings/net/wireless/qcom,ath11k.yaml
@@ -0,0 +1,277 @@
+# SPDX-License-Identifier: BSD-3-Clause-Clear
+# Copyright (c) 2018-2019 The Linux Foundation. All rights reserved.
+
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/net/wireless/qcom,ath11k.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Qualcomm Technologies ath11k wireless devices Generic Binding
+
+maintainers:
+ - Kalle Valo <kvalo@codeaurora.org>
+
+description: |
+ These are dt entries used on ath11k driver. AHB based ipq8074 uses most of the properties defined in this doc.
+
+properties:
+ compatible:
+ const: "qcom,ipq8074-wifi"
+
+ reg:
+ description: Address and length of the register set for the device
+ maxItems: 1
+
+ interrupts:
+ minItems: 53
+ maxItems: 53
+ items:
+ - description: misc-pulse1 interrupt events
+ - description: misc-latch interrupt events
+ - description: sw exception interrupt events
+ - description: watchdog interrupt events
+ - description: interrupt event for ring CE0
+ - description: interrupt event for ring CE1
+ - description: interrupt event for ring CE2
+ - description: interrupt event for ring CE3
+ - description: interrupt event for ring CE4
+ - description: interrupt event for ring CE5
+ - description: interrupt event for ring CE6
+ - description: interrupt event for ring CE7
+ - description: interrupt event for ring CE8
+ - description: interrupt event for ring CE9
+ - description: interrupt event for ring CE10
+ - description: interrupt event for ring CE11
+ - description: interrupt event for ring host2wbm-desc-feed
+ - description: interrupt event for ring host2reo-re-injection
+ - description: interrupt event for ring host2reo-command
+ - description: interrupt event for ring host2rxdma-monitor-ring3
+ - description: interrupt event for ring host2rxdma-monitor-ring2
+ - description: interrupt event for ring host2rxdma-monitor-ring1
+ - description: interrupt event for ring reo2ost-exception
+ - description: interrupt event for ring wbm2host-rx-release
+ - description: interrupt event for ring reo2host-status
+ - description: interrupt event for ring reo2host-destination-ring4
+ - description: interrupt event for ring reo2host-destination-ring3
+ - description: interrupt event for ring reo2host-destination-ring2
+ - description: interrupt event for ring reo2host-destination-ring1
+ - description: interrupt event for ring rxdma2host-monitor-destination-mac3
+ - description: interrupt event for ring rxdma2host-monitor-destination-mac2
+ - description: interrupt event for ring rxdma2host-monitor-destination-mac1
+ - description: interrupt event for ring ppdu-end-interrupts-mac3
+ - description: interrupt event for ring ppdu-end-interrupts-mac2
+ - description: interrupt event for ring ppdu-end-interrupts-mac1
+ - description: interrupt event for ring rxdma2host-monitor-status-ring-mac3
+ - description: interrupt event for ring rxdma2host-monitor-status-ring-mac2
+ - description: interrupt event for ring rxdma2host-monitor-status-ring-mac1
+ - description: interrupt event for ring host2rxdma-host-buf-ring-mac3
+ - description: interrupt event for ring host2rxdma-host-buf-ring-mac2
+ - description: interrupt event for ring host2rxdma-host-buf-ring-mac1
+ - description: interrupt event for ring rxdma2host-destination-ring-mac3
+ - description: interrupt event for ring rxdma2host-destination-ring-mac2
+ - description: interrupt event for ring rxdma2host-destination-ring-mac1
+ - description: interrupt event for ring host2tcl-input-ring4
+ - description: interrupt event for ring host2tcl-input-ring3
+ - description: interrupt event for ring host2tcl-input-ring2
+ - description: interrupt event for ring host2tcl-input-ring1
+ - description: interrupt event for ring wbm2host-tx-completions-ring3
+ - description: interrupt event for ring wbm2host-tx-completions-ring2
+ - description: interrupt event for ring wbm2host-tx-completions-ring1
+ - description: interrupt event for ring tcl2host-status-ring
+
+
+ interrupt-names:
+ minItems: 53
+ maxItems: 53
+ items:
+ - const: misc-pulse1
+ - const: misc-latch
+ - const: sw-exception
+ - const: watchdog
+ - const: ce0
+ - const: ce1
+ - const: ce2
+ - const: ce3
+ - const: ce4
+ - const: ce5
+ - const: ce6
+ - const: ce7
+ - const: ce8
+ - const: ce9
+ - const: ce10
+ - const: ce11
+ - const: host2wbm-desc-feed
+ - const: host2reo-re-injection
+ - const: host2reo-command
+ - const: host2rxdma-monitor-ring3
+ - const: host2rxdma-monitor-ring2
+ - const: host2rxdma-monitor-ring1
+ - const: reo2ost-exception
+ - const: wbm2host-rx-release
+ - const: reo2host-status
+ - const: reo2host-destination-ring4
+ - const: reo2host-destination-ring3
+ - const: reo2host-destination-ring2
+ - const: reo2host-destination-ring1
+ - const: rxdma2host-monitor-destination-mac3
+ - const: rxdma2host-monitor-destination-mac2
+ - const: rxdma2host-monitor-destination-mac1
+ - const: ppdu-end-interrupts-mac3
+ - const: ppdu-end-interrupts-mac2
+ - const: ppdu-end-interrupts-mac1
+ - const: rxdma2host-monitor-status-ring-mac3
+ - const: rxdma2host-monitor-status-ring-mac2
+ - const: rxdma2host-monitor-status-ring-mac1
+ - const: host2rxdma-host-buf-ring-mac3
+ - const: host2rxdma-host-buf-ring-mac2
+ - const: host2rxdma-host-buf-ring-mac1
+ - const: rxdma2host-destination-ring-mac3
+ - const: rxdma2host-destination-ring-mac2
+ - const: rxdma2host-destination-ring-mac1
+ - const: host2tcl-input-ring4
+ - const: host2tcl-input-ring3
+ - const: host2tcl-input-ring2
+ - const: host2tcl-input-ring1
+ - const: wbm2host-tx-completions-ring3
+ - const: wbm2host-tx-completions-ring2
+ - const: wbm2host-tx-completions-ring1
+ - const: tcl2host-status-ring
+
+ qcom,rproc:
+ $ref: /schemas/types.yaml#definitions/phandle
+ description:
+ DT entry of q6v5-wcss remoteproc driver.
+ Phandle to a node that can contain the following properties
+ * compatible
+ * reg
+ * reg-names
+
+required:
+ - compatible
+ - reg
+ - interrupts
+ - interrupt-names
+ - qcom,rproc
+
+additionalProperties: false
+
+examples:
+ - |
+
+ q6v5_wcss: q6v5_wcss@CD00000 {
+ compatible = "qcom,ipq8074-wcss-pil";
+ reg = <0xCD00000 0x4040>,
+ <0x4AB000 0x20>;
+ reg-names = "qdsp6",
+ "rmb";
+ };
+
+ wifi0: wifi@c000000 {
+ compatible = "qcom,ipq8074-wifi";
+ reg = <0xc000000 0x2000000>;
+ interrupts = <0 320 1>,
+ <0 319 1>,
+ <0 318 1>,
+ <0 317 1>,
+ <0 316 1>,
+ <0 315 1>,
+ <0 314 1>,
+ <0 311 1>,
+ <0 310 1>,
+ <0 411 1>,
+ <0 410 1>,
+ <0 40 1>,
+ <0 39 1>,
+ <0 302 1>,
+ <0 301 1>,
+ <0 37 1>,
+ <0 36 1>,
+ <0 296 1>,
+ <0 295 1>,
+ <0 294 1>,
+ <0 293 1>,
+ <0 292 1>,
+ <0 291 1>,
+ <0 290 1>,
+ <0 289 1>,
+ <0 288 1>,
+ <0 239 1>,
+ <0 236 1>,
+ <0 235 1>,
+ <0 234 1>,
+ <0 233 1>,
+ <0 232 1>,
+ <0 231 1>,
+ <0 230 1>,
+ <0 229 1>,
+ <0 228 1>,
+ <0 224 1>,
+ <0 223 1>,
+ <0 203 1>,
+ <0 183 1>,
+ <0 180 1>,
+ <0 179 1>,
+ <0 178 1>,
+ <0 177 1>,
+ <0 176 1>,
+ <0 163 1>,
+ <0 162 1>,
+ <0 160 1>,
+ <0 159 1>,
+ <0 158 1>,
+ <0 157 1>,
+ <0 156 1>;
+ interrupt-names = "misc-pulse1",
+ "misc-latch",
+ "sw-exception",
+ "watchdog",
+ "ce0",
+ "ce1",
+ "ce2",
+ "ce3",
+ "ce4",
+ "ce5",
+ "ce6",
+ "ce7",
+ "ce8",
+ "ce9",
+ "ce10",
+ "ce11",
+ "host2wbm-desc-feed",
+ "host2reo-re-injection",
+ "host2reo-command",
+ "host2rxdma-monitor-ring3",
+ "host2rxdma-monitor-ring2",
+ "host2rxdma-monitor-ring1",
+ "reo2ost-exception",
+ "wbm2host-rx-release",
+ "reo2host-status",
+ "reo2host-destination-ring4",
+ "reo2host-destination-ring3",
+ "reo2host-destination-ring2",
+ "reo2host-destination-ring1",
+ "rxdma2host-monitor-destination-mac3",
+ "rxdma2host-monitor-destination-mac2",
+ "rxdma2host-monitor-destination-mac1",
+ "ppdu-end-interrupts-mac3",
+ "ppdu-end-interrupts-mac2",
+ "ppdu-end-interrupts-mac1",
+ "rxdma2host-monitor-status-ring-mac3",
+ "rxdma2host-monitor-status-ring-mac2",
+ "rxdma2host-monitor-status-ring-mac1",
+ "host2rxdma-host-buf-ring-mac3",
+ "host2rxdma-host-buf-ring-mac2",
+ "host2rxdma-host-buf-ring-mac1",
+ "rxdma2host-destination-ring-mac3",
+ "rxdma2host-destination-ring-mac2",
+ "rxdma2host-destination-ring-mac1",
+ "host2tcl-input-ring4",
+ "host2tcl-input-ring3",
+ "host2tcl-input-ring2",
+ "host2tcl-input-ring1",
+ "wbm2host-tx-completions-ring3",
+ "wbm2host-tx-completions-ring2",
+ "wbm2host-tx-completions-ring1",
+ "tcl2host-status-ring";
+ qcom,rproc = <&q6v5_wcss>;
+ };
next prev parent reply other threads:[~2019-10-20 10:04 UTC|newest]
Thread overview: 58+ messages / expand[flat|nested] mbox.gz Atom feed top
2019-10-20 10:03 [PATCH v2 00/49] ath11k: driver for Qualcomm IEEE 802.11ax devices Kalle Valo
2019-10-20 10:03 ` Kalle Valo [this message]
2019-10-25 21:30 ` [PATCH v2 01/49] dt: bindings: net: add qcom,ath11k.yaml Rob Herring
2019-10-27 13:28 ` Kalle Valo
2019-10-27 20:56 ` Rob Herring
2019-11-05 14:55 ` Kalle Valo
2019-11-07 15:38 ` Kalle Valo
2019-11-15 12:18 ` Kalle Valo
2019-10-20 10:03 ` [PATCH v2 02/49] ath11k: add Kconfig Kalle Valo
2019-10-21 20:53 ` Jeff Johnson
2019-11-07 16:04 ` Kalle Valo
2019-10-20 10:03 ` [PATCH v2 03/49] ath11k: add Makefile Kalle Valo
2019-10-20 10:03 ` [PATCH v2 04/49] ath11k: add ahb.c Kalle Valo
2019-10-20 10:03 ` [PATCH v2 05/49] ath11k: add ahb.h Kalle Valo
2019-10-20 10:03 ` [PATCH v2 06/49] ath11k: add ce.c Kalle Valo
2019-10-20 10:03 ` [PATCH v2 07/49] ath11k: add ce.h Kalle Valo
2019-10-20 10:03 ` [PATCH v2 08/49] ath11k: add core.c Kalle Valo
2019-10-20 10:03 ` [PATCH v2 09/49] ath11k: add core.h Kalle Valo
2019-10-20 10:03 ` [PATCH v2 10/49] ath11k: add debug.c Kalle Valo
2019-10-20 10:03 ` [PATCH v2 11/49] ath11k: add debug.h Kalle Valo
2019-10-20 10:03 ` [PATCH v2 12/49] ath11k: add debug_htt_stats.c Kalle Valo
2019-10-20 10:03 ` [PATCH v2 13/49] ath11k: add debug_htt_stats.h Kalle Valo
2019-10-20 10:03 ` [PATCH v2 14/49] ath11k: add debugfs_sta.c Kalle Valo
2019-10-20 10:03 ` [PATCH v2 15/49] ath11k: add dp.c Kalle Valo
2019-10-20 10:03 ` [PATCH v2 16/49] ath11k: add dp.h Kalle Valo
2019-10-20 10:03 ` [PATCH v2 17/49] ath11k: add dp_rx.c Kalle Valo
2019-10-20 10:03 ` [PATCH v2 18/49] ath11k: add dp_rx.h Kalle Valo
2019-10-20 10:03 ` [PATCH v2 19/49] ath11k: add dp_tx.c Kalle Valo
2019-10-20 10:03 ` [PATCH v2 20/49] ath11k: add dp_tx.h Kalle Valo
2019-10-20 10:03 ` [PATCH v2 21/49] ath11k: add hal.c Kalle Valo
2019-10-20 10:03 ` [PATCH v2 22/49] ath11k: add hal.h Kalle Valo
2019-10-20 10:03 ` [PATCH v2 23/49] ath11k: add hal_desc.h Kalle Valo
2019-10-20 10:03 ` [PATCH v2 24/49] ath11k: add hal_rx.c Kalle Valo
2019-10-20 10:03 ` [PATCH v2 25/49] ath11k: add hal_rx.h Kalle Valo
2019-10-20 10:03 ` [PATCH v2 26/49] ath11k: add hal_tx.c Kalle Valo
2019-10-20 10:03 ` [PATCH v2 27/49] ath11k: add hal_tx.h Kalle Valo
2019-10-20 10:03 ` [PATCH v2 28/49] ath11k: add htc.c Kalle Valo
2019-10-20 10:03 ` [PATCH v2 29/49] ath11k: add htc.h Kalle Valo
2019-10-20 10:03 ` [PATCH v2 30/49] ath11k: add hw.h Kalle Valo
2019-10-20 10:03 ` [PATCH v2 31/49] ath11k: add mac.c Kalle Valo
2019-10-20 10:03 ` [PATCH v2 32/49] ath11k: add mac.h Kalle Valo
2019-10-20 10:03 ` [PATCH v2 33/49] ath11k: add peer.c Kalle Valo
2019-10-20 10:03 ` [PATCH v2 34/49] ath11k: add peer.h Kalle Valo
2019-10-20 10:03 ` [PATCH v2 35/49] ath11k: add qmi.c Kalle Valo
2019-10-20 10:03 ` [PATCH v2 36/49] ath11k: add qmi.h Kalle Valo
2019-10-20 10:03 ` [PATCH v2 37/49] ath11k: add reg.c Kalle Valo
2019-10-20 10:03 ` [PATCH v2 38/49] ath11k: add reg.h Kalle Valo
2019-10-20 10:03 ` [PATCH v2 39/49] ath11k: add rx_desc.h Kalle Valo
2019-10-20 10:03 ` [PATCH v2 40/49] ath11k: add testmode.c Kalle Valo
2019-10-20 10:03 ` [PATCH v2 41/49] ath11k: add testmode.h Kalle Valo
2019-10-20 10:04 ` [PATCH v2 42/49] ath11k: add testmode_i.h Kalle Valo
2019-10-20 10:04 ` [PATCH v2 43/49] ath11k: add trace.c Kalle Valo
2019-10-20 10:04 ` [PATCH v2 44/49] ath11k: add trace.h Kalle Valo
2019-10-20 10:04 ` [PATCH v2 45/49] ath11k: add wmi.c Kalle Valo
2019-10-20 10:04 ` [PATCH v2 46/49] ath11k: add wmi.h Kalle Valo
2019-10-20 10:04 ` [PATCH v2 47/49] ath: add ath11k to Makefile Kalle Valo
2019-10-20 10:04 ` [PATCH v2 48/49] ath: add ath11k to Kconfig Kalle Valo
2019-10-20 10:04 ` [PATCH v2 49/49] MAINTAINERS: add ath11k Kalle Valo
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=1571565847-10338-2-git-send-email-kvalo@codeaurora.org \
--to=kvalo@codeaurora.org \
--cc=ath11k@lists.infradead.org \
--cc=devicetree@vger.kernel.org \
--cc=linux-wireless@vger.kernel.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).