[PATCH v6 0/2] Add PWM support for Intel Keem Bay SoC

[PATCH v6 0/2] Add PWM support for Intel Keem Bay SoC

[vineetha.g.jaya.kumaran]

From: "Vineetha G. Jaya Kumaran" <vineetha.g.jaya.kumaran@intel.com>

Hi,

This patch set enables support for PWM on the Intel Keem Bay SoC.
Keem Bay is an ARM based SoC, and the GPIO module allows
configuration of 6 PWM outputs. Patch 1 adds the PWM driver and
Patch 2 is for the required Device Tree bindings documentation.

This driver was tested on the Keem Bay evaluation module board.

Thank you.

Best regards,
Vineetha

Changes since v5:
-Reorder symbols/Kconfig in drivers/pwm/Kconfig and drivers/pwm/Makefile
-Use "Limitations" for consistency
-Add clk_prepare_enable()
-Reorder keembay_pwm_get_state() function call
-Rework if conditional for channel disablement in .apply()
-Remove channel disabling from .probe(), and clear LEADIN register bits in .apply instead
-Update commit message for Patch 1

Changes since v4:
-Add co-developed-by tag
-Include mod_devicetable.h and remove of.h
-Update comment with correct calulation for high/low time
-Fix missing return from dev_err_probe

Changes since v3:
-Removed variable for address and calculate in place instead
-Utilized u32_replace_bits() when updating KMB_PWM_LEADIN_OFFSET
-Utilized dev_err_probe() for error reporting
-Updated comments to use physical units
-Updated error check for pwmchip_add()

Changes since v2:
-Include documentation about HW limitation/behaviour
-Use hex values for KMB_PWM_COUNT_MAX
-Redefine register macros
-Utilize FIELD_GET/FIELD_PREP for calculating pwm_l/h_count and pwm_count
-Round up duty cycle/period values
-Get current hardware state in .apply instead of cached values
-Do a polarity check before .enabled
-Round high time/low time to closest value
-Set enable bit in KMB_PWM_LEADIN_OFFSET to 0 in probe
-Correct the naming for MODULE_ALIAS
-Add additionalProperties: false in DT bindings

Changes since v1:
-Updated licensing info, "clocks" property and example in DT bindings
-Updated name of DT bindings document to match compatible string
-Removed 1 patch for addition of new sysfs attribute "count"
-Added support for COMPILE_TEST in Kconfig
-Updated naming of defines and regmap attribute
-Updated calculation of waveform high time and low time
-Added range checking for waveform high/low time
-Implemented .get_state
-Removed register writes for lead-in and count values (left to default)
-Updated register access to single-access
-Folded keembay_pwm_enable/disable_channel, keembay_pwm_config_period/duty_cycle,
 and keembay_pwm_config into keembay_pwm_apply
-Updated error messages/error codes
-Removed pwm_disable from keembay_pwm_remove
-Removed clk_prepare/clk_enable/clk_disable from driver

Lai, Poey Seng (1):
  pwm: Add PWM driver for Intel Keem Bay

Vineetha G. Jaya Kumaran (1):
  dt-bindings: pwm: keembay: Add bindings for Intel Keem Bay PWM

 .../devicetree/bindings/pwm/intel,keembay-pwm.yaml |  47 +++++
 drivers/pwm/Kconfig                                |   9 +
 drivers/pwm/Makefile                               |   1 +
 drivers/pwm/pwm-keembay.c                          | 232 +++++++++++++++++++++
 4 files changed, 289 insertions(+)
 create mode 100644 Documentation/devicetree/bindings/pwm/intel,keembay-pwm.yaml
 create mode 100644 drivers/pwm/pwm-keembay.c

-- 
1.9.1

[PATCH v6 1/2] pwm: Add PWM driver for Intel Keem Bay

[vineetha.g.jaya.kumaran]

From: "Lai, Poey Seng" <poey.seng.lai@intel.com>

The Intel Keem Bay SoC requires PWM support.
Add the pwm-keembay driver to enable this.

Co-developed-by: Vineetha G. Jaya Kumaran <vineetha.g.jaya.kumaran@intel.com>
Signed-off-by: Lai, Poey Seng <poey.seng.lai@intel.com>
Signed-off-by: Vineetha G. Jaya Kumaran <vineetha.g.jaya.kumaran@intel.com>
---
 drivers/pwm/Kconfig       |   9 ++
 drivers/pwm/Makefile      |   1 +
 drivers/pwm/pwm-keembay.c | 232 ++++++++++++++++++++++++++++++++++++++++++++++
 3 files changed, 242 insertions(+)
 create mode 100644 drivers/pwm/pwm-keembay.c

diff --git a/drivers/pwm/Kconfig b/drivers/pwm/Kconfig
index 7dbcf69..4f1fdbc 100644
--- a/drivers/pwm/Kconfig
+++ b/drivers/pwm/Kconfig
@@ -254,6 +254,15 @@ config PWM_JZ4740
 	  To compile this driver as a module, choose M here: the module
 	  will be called pwm-jz4740.
 
+config PWM_KEEMBAY
+	tristate "Intel Keem Bay PWM driver"
+	depends on ARM64 || COMPILE_TEST
+	help
+	  The platform driver for Intel Keem Bay PWM controller.
+
+	  To compile this driver as a module, choose M here: the module
+	  will be called pwm-keembay.
+
 config PWM_LP3943
 	tristate "TI/National Semiconductor LP3943 PWM support"
 	depends on MFD_LP3943
diff --git a/drivers/pwm/Makefile b/drivers/pwm/Makefile
index 2c2ba0a..a105112 100644
--- a/drivers/pwm/Makefile
+++ b/drivers/pwm/Makefile
@@ -22,6 +22,7 @@ obj-$(CONFIG_PWM_IMX27)		+= pwm-imx27.o
 obj-$(CONFIG_PWM_IMX_TPM)	+= pwm-imx-tpm.o
 obj-$(CONFIG_PWM_IQS620A)	+= pwm-iqs620a.o
 obj-$(CONFIG_PWM_JZ4740)	+= pwm-jz4740.o
+obj-$(CONFIG_PWM_KEEMBAY)	+= pwm-keembay.o
 obj-$(CONFIG_PWM_LP3943)	+= pwm-lp3943.o
 obj-$(CONFIG_PWM_LPC18XX_SCT)	+= pwm-lpc18xx-sct.o
 obj-$(CONFIG_PWM_LPC32XX)	+= pwm-lpc32xx.o
diff --git a/drivers/pwm/pwm-keembay.c b/drivers/pwm/pwm-keembay.c
new file mode 100644
index 00000000..6f41b1c
--- /dev/null
+++ b/drivers/pwm/pwm-keembay.c
@@ -0,0 +1,232 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Intel Keem Bay PWM driver
+ *
+ * Copyright (C) 2020 Intel Corporation
+ * Authors: Lai Poey Seng <poey.seng.lai@intel.com>
+ *          Vineetha G. Jaya Kumaran <vineetha.g.jaya.kumaran@intel.com>
+ *
+ * Limitations:
+ * - Upon disabling a channel, the currently running
+ *   period will not be completed. However, upon
+ *   reconfiguration of the duty cycle/period, the
+ *   currently running period will be completed first.
+ */
+
+#include <linux/bitfield.h>
+#include <linux/clk.h>
+#include <linux/io.h>
+#include <linux/mod_devicetable.h>
+#include <linux/module.h>
+#include <linux/platform_device.h>
+#include <linux/pwm.h>
+#include <linux/regmap.h>
+
+#define KMB_TOTAL_PWM_CHANNELS		6
+#define KMB_PWM_COUNT_MAX		0xffff
+#define KMB_PWM_EN_BIT			BIT(31)
+
+/* Mask */
+#define KMB_PWM_HIGH_MASK		GENMASK(31, 16)
+#define KMB_PWM_LOW_MASK		GENMASK(15, 0)
+#define KMB_PWM_LEADIN_MASK		GENMASK(30, 0)
+
+/* PWM Register offset */
+#define KMB_PWM_LEADIN_OFFSET(ch)	(0x00 + 4 * (ch))
+#define KMB_PWM_HIGHLOW_OFFSET(ch)	(0x20 + 4 * (ch))
+
+struct keembay_pwm {
+	struct pwm_chip chip;
+	struct device *dev;
+	struct clk *clk;
+	void __iomem *base;
+};
+
+static inline struct keembay_pwm *to_keembay_pwm_dev(struct pwm_chip *chip)
+{
+	return container_of(chip, struct keembay_pwm, chip);
+}
+
+static inline void keembay_pwm_update_bits(struct keembay_pwm *priv, u32 mask,
+					   u32 val, u32 offset)
+{
+	u32 buff = readl(priv->base + offset);
+
+	buff = u32_replace_bits(buff, val, mask);
+	writel(buff, priv->base + offset);
+}
+
+static void keembay_pwm_enable(struct keembay_pwm *priv, int ch)
+{
+	keembay_pwm_update_bits(priv, KMB_PWM_EN_BIT, 1,
+				KMB_PWM_LEADIN_OFFSET(ch));
+}
+
+static void keembay_pwm_disable(struct keembay_pwm *priv, int ch)
+{
+	keembay_pwm_update_bits(priv, KMB_PWM_EN_BIT, 0,
+				KMB_PWM_LEADIN_OFFSET(ch));
+}
+
+static void keembay_pwm_get_state(struct pwm_chip *chip, struct pwm_device *pwm,
+				  struct pwm_state *state)
+{
+	struct keembay_pwm *priv = to_keembay_pwm_dev(chip);
+	unsigned long long pwm_h_count, pwm_l_count;
+	unsigned long clk_rate;
+	u32 buff;
+
+	clk_rate = clk_get_rate(priv->clk);
+
+	/* Read channel enabled status */
+	buff = readl(priv->base + KMB_PWM_LEADIN_OFFSET(pwm->hwpwm));
+	if (buff & KMB_PWM_EN_BIT)
+		state->enabled = true;
+	else
+		state->enabled = false;
+
+	/* Read period and duty cycle */
+	buff = readl(priv->base + KMB_PWM_HIGHLOW_OFFSET(pwm->hwpwm));
+	pwm_l_count = FIELD_GET(KMB_PWM_LOW_MASK, buff) * NSEC_PER_SEC;
+	pwm_h_count = FIELD_GET(KMB_PWM_HIGH_MASK, buff) * NSEC_PER_SEC;
+	state->duty_cycle = DIV_ROUND_UP_ULL(pwm_h_count, clk_rate);
+	state->period = DIV_ROUND_UP_ULL(pwm_h_count + pwm_l_count, clk_rate);
+}
+
+static int keembay_pwm_apply(struct pwm_chip *chip, struct pwm_device *pwm,
+			     const struct pwm_state *state)
+{
+	struct keembay_pwm *priv = to_keembay_pwm_dev(chip);
+	struct pwm_state current_state;
+	u16 pwm_h_count, pwm_l_count;
+	unsigned long long div;
+	unsigned long clk_rate;
+	u32 pwm_count = 0;
+
+	if (state->polarity != PWM_POLARITY_NORMAL)
+		return -ENOSYS;
+
+	keembay_pwm_update_bits(priv, KMB_PWM_LEADIN_MASK, 0,
+				KMB_PWM_LEADIN_OFFSET(pwm->hwpwm));
+
+	keembay_pwm_get_state(chip, pwm, &current_state);
+
+	if (!state->enabled) {
+		if (current_state.enabled)
+			keembay_pwm_disable(priv, pwm->hwpwm);
+		return 0;
+	}
+
+	/*
+	 * The upper 16 bits of the KMB_PWM_HIGHLOW_OFFSET register contain
+	 * the high time of the waveform, while the last 16 bits contain
+	 * the low time of the waveform, in terms of clock cycles.
+	 *
+	 * high time = clock rate * duty cycle
+	 * low time =  clock rate * (period - duty cycle)
+	 *
+	 * e.g. For period 50us, duty cycle 30us, and clock rate 500MHz:
+	 * high time = 500MHz * 30us = 0x3A98
+	 * low time = 500MHz * 20us = 0x2710
+	 * Value written to KMB_PWM_HIGHLOW_OFFSET = 0x3A982710
+	 */
+
+	clk_rate = clk_get_rate(priv->clk);
+
+	/* Configure waveform high time */
+	div = clk_rate * state->duty_cycle;
+	div = DIV_ROUND_CLOSEST_ULL(div, NSEC_PER_SEC);
+	if (div > KMB_PWM_COUNT_MAX)
+		return -ERANGE;
+
+	pwm_h_count = div;
+
+	/* Configure waveform low time */
+	div = clk_rate * (state->period - state->duty_cycle);
+	div = DIV_ROUND_CLOSEST_ULL(div, NSEC_PER_SEC);
+	if (div > KMB_PWM_COUNT_MAX)
+		return -ERANGE;
+
+	pwm_l_count = div;
+
+	pwm_count = FIELD_PREP(KMB_PWM_HIGH_MASK, pwm_h_count) |
+		    FIELD_PREP(KMB_PWM_LOW_MASK, pwm_l_count);
+
+	writel(pwm_count, priv->base + KMB_PWM_HIGHLOW_OFFSET(pwm->hwpwm));
+
+	if (state->enabled && !current_state.enabled)
+		keembay_pwm_enable(priv, pwm->hwpwm);
+
+	return 0;
+}
+
+static const struct pwm_ops keembay_pwm_ops = {
+	.owner = THIS_MODULE,
+	.apply = keembay_pwm_apply,
+	.get_state = keembay_pwm_get_state,
+};
+
+static int keembay_pwm_probe(struct platform_device *pdev)
+{
+	struct device *dev = &pdev->dev;
+	struct keembay_pwm *priv;
+	int ret;
+
+	priv = devm_kzalloc(dev, sizeof(*priv), GFP_KERNEL);
+	if (!priv)
+		return -ENOMEM;
+
+	priv->clk = devm_clk_get(&pdev->dev, NULL);
+	if (IS_ERR(priv->clk))
+		return dev_err_probe(dev, PTR_ERR(priv->clk), "Failed to get clock\n");
+
+	ret = clk_prepare_enable(priv->clk);
+	if (ret)
+		return ret;
+
+	priv->base = devm_platform_ioremap_resource(pdev, 0);
+	if (IS_ERR(priv->base))
+		return PTR_ERR(priv->base);
+
+	priv->chip.base = -1;
+	priv->chip.dev = dev;
+	priv->chip.ops = &keembay_pwm_ops;
+	priv->chip.npwm = KMB_TOTAL_PWM_CHANNELS;
+
+	ret = pwmchip_add(&priv->chip);
+	if (ret) {
+		dev_err(dev, "Failed to add PWM chip: %pe\n", ERR_PTR(ret));
+		return ret;
+	}
+
+	platform_set_drvdata(pdev, priv);
+
+	return 0;
+}
+
+static int keembay_pwm_remove(struct platform_device *pdev)
+{
+	struct keembay_pwm *priv = platform_get_drvdata(pdev);
+
+	return pwmchip_remove(&priv->chip);
+}
+
+static const struct of_device_id keembay_pwm_of_match[] = {
+	{ .compatible = "intel,keembay-pwm" },
+	{ }
+};
+MODULE_DEVICE_TABLE(of, keembay_pwm_of_match);
+
+static struct platform_driver keembay_pwm_driver = {
+	.probe	= keembay_pwm_probe,
+	.remove	= keembay_pwm_remove,
+	.driver	= {
+		.name = "pwm-keembay",
+		.of_match_table = keembay_pwm_of_match,
+	},
+};
+module_platform_driver(keembay_pwm_driver);
+
+MODULE_ALIAS("platform:pwm-keembay");
+MODULE_DESCRIPTION("Intel Keem Bay PWM driver");
+MODULE_LICENSE("GPL v2");
-- 
1.9.1

[PATCH v6 2/2] dt-bindings: pwm: keembay: Add bindings for Intel Keem Bay PWM

[vineetha.g.jaya.kumaran]

From: "Vineetha G. Jaya Kumaran" <vineetha.g.jaya.kumaran@intel.com>

Add PWM Device Tree bindings documentation for the Intel Keem Bay SoC.

Reviewed-by: Rob Herring <robh@kernel.org>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Vineetha G. Jaya Kumaran <vineetha.g.jaya.kumaran@intel.com>
---
 .../devicetree/bindings/pwm/intel,keembay-pwm.yaml | 47 ++++++++++++++++++++++
 1 file changed, 47 insertions(+)
 create mode 100644 Documentation/devicetree/bindings/pwm/intel,keembay-pwm.yaml

diff --git a/Documentation/devicetree/bindings/pwm/intel,keembay-pwm.yaml b/Documentation/devicetree/bindings/pwm/intel,keembay-pwm.yaml
new file mode 100644
index 00000000..a374334
--- /dev/null
+++ b/Documentation/devicetree/bindings/pwm/intel,keembay-pwm.yaml
@@ -0,0 +1,47 @@
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+# Copyright (C) 2020 Intel Corporation
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/pwm/intel,keembay-pwm.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Intel Keem Bay PWM Device Tree Bindings
+
+maintainers:
+  - Vineetha G. Jaya Kumaran <vineetha.g.jaya.kumaran@intel.com>
+
+allOf:
+  - $ref: pwm.yaml#
+
+properties:
+  compatible:
+    enum:
+      - intel,keembay-pwm
+
+  reg:
+    maxItems: 1
+
+  clocks:
+    maxItems: 1
+
+  "#pwm-cells":
+    const: 2
+
+required:
+ - compatible
+ - reg
+ - clocks
+ - '#pwm-cells'
+
+additionalProperties: false
+
+examples:
+  - |
+    #define KEEM_BAY_A53_GPIO
+
+    pwm@203200a0 {
+      compatible = "intel,keembay-pwm";
+      reg = <0x203200a0 0xe8>;
+      clocks = <&scmi_clk KEEM_BAY_A53_GPIO>;
+      #pwm-cells = <2>;
+    };
-- 
1.9.1

Re: [PATCH v6 1/2] pwm: Add PWM driver for Intel Keem Bay

[Andy Shevchenko]

On Mon, Sep 07, 2020 at 08:07:49PM +0800, vineetha.g.jaya.kumaran@intel.com wrote:
> From: "Lai, Poey Seng" <poey.seng.lai@intel.com>
> 
> The Intel Keem Bay SoC requires PWM support.
> Add the pwm-keembay driver to enable this.

Hadn't I given a tag already? If so, where is it?

> Co-developed-by: Vineetha G. Jaya Kumaran <vineetha.g.jaya.kumaran@intel.com>
> Signed-off-by: Lai, Poey Seng <poey.seng.lai@intel.com>
> Signed-off-by: Vineetha G. Jaya Kumaran <vineetha.g.jaya.kumaran@intel.com>

-- 
With Best Regards,
Andy Shevchenko