[PATCH v2 1/2] ASoC: codecs: Add PCM186x binding documentation

[PATCH v2 1/2] ASoC: codecs: Add PCM186x binding documentation

[Andrew F. Davis]

Add the dt-binding documentation for the TI PCM186x 2ch and 4ch Audio
ADCs With Universal Front End.

Signed-off-by: Andrew F. Davis <afd@ti.com>
Acked-by: Rob Herring <robh@kernel.org>
---

Changes from v1:
 - pcm186x@4a -> audio-codec@4a
 - Added Acked-by

 .../devicetree/bindings/sound/pcm186x.txt          | 42 ++++++++++++++++++++++
 1 file changed, 42 insertions(+)
 create mode 100644 Documentation/devicetree/bindings/sound/pcm186x.txt

diff --git a/Documentation/devicetree/bindings/sound/pcm186x.txt b/Documentation/devicetree/bindings/sound/pcm186x.txt
new file mode 100644
index 000000000000..1087f4855980
--- /dev/null
+++ b/Documentation/devicetree/bindings/sound/pcm186x.txt
@@ -0,0 +1,42 @@
+Texas Instruments PCM186x Universal Audio ADC
+
+These devices support both I2C and SPI (configured with pin strapping
+on the board).
+
+Required properties:
+
+ - compatible : "ti,pcm1862",
+                "ti,pcm1863",
+                "ti,pcm1864",
+                "ti,pcm1865"
+
+ - reg : The I2C address of the device for I2C, the chip select
+         number for SPI.
+
+ - avdd-supply: Analog core power supply (3.3v)
+ - dvdd-supply: Digital core power supply
+ - iovdd-supply: Digital IO power supply
+        See regulator/regulator.txt for more information
+
+CODEC input pins:
+ * VINL1
+ * VINR1
+ * VINL2
+ * VINR2
+ * VINL3
+ * VINR3
+ * VINL4
+ * VINR4
+
+The pins can be used in referring sound node's audio-routing property.
+
+Example:
+
+	pcm186x: audio-codec@4a {
+		compatible = "ti,pcm1865";
+		reg = <0x4a>;
+
+		avdd-supply = <&reg_3v3_analog>;
+		dvdd-supply = <&reg_3v3>;
+		iovdd-supply = <&reg_1v8>;
+	};
-- 
2.15.0

[PATCH v2 2/2] ASoC: codecs: Add initial PCM1862/63/64/65 universal ADC driver

[Andrew F. Davis]

From: Andreas Dannenberg <dannenberg@ti.com>

This is an initial version of the PCM186x codec driver supporting both
2-channel and 4-channel device variants. Not all device features are
supported yet such as master/slave mode PLL configuration for which the
codec driver currently relies on the PCM186x built-in clock
auto-detection feature or the connection of digital microphones.
However here is what's here and what should work:

- Support for SPI and I2C low-level interfaces
- Regmap support and basic register definitions
- Input Mixer and Mux selection
- I2C, LJ, and TDM DAI format support

Signed-off-by: Andreas Dannenberg <dannenberg@ti.com>
Signed-off-by: Michael Stecklein <m-stecklein@ti.com>
Signed-off-by: Andrew F. Davis <afd@ti.com>
---

Changes from v1:
 - Remove extra debug statements
 - Fix volume control names
 - Power up supplies before device reset

 sound/soc/codecs/Kconfig       |  17 +
 sound/soc/codecs/Makefile      |   6 +
 sound/soc/codecs/pcm186x-i2c.c |  69 ++++
 sound/soc/codecs/pcm186x-spi.c |  69 ++++
 sound/soc/codecs/pcm186x.c     | 773 +++++++++++++++++++++++++++++++++++++++++
 sound/soc/codecs/pcm186x.h     | 221 ++++++++++++
 6 files changed, 1155 insertions(+)
 create mode 100644 sound/soc/codecs/pcm186x-i2c.c
 create mode 100644 sound/soc/codecs/pcm186x-spi.c
 create mode 100644 sound/soc/codecs/pcm186x.c
 create mode 100644 sound/soc/codecs/pcm186x.h

diff --git a/sound/soc/codecs/Kconfig b/sound/soc/codecs/Kconfig
index a42ddbc93f3d..dda8c01170b3 100644
--- a/sound/soc/codecs/Kconfig
+++ b/sound/soc/codecs/Kconfig
@@ -109,6 +109,8 @@ config SND_SOC_ALL_CODECS
 	select SND_SOC_PCM1681 if I2C
 	select SND_SOC_PCM179X_I2C if I2C
 	select SND_SOC_PCM179X_SPI if SPI_MASTER
+	select SND_SOC_PCM186X_I2C if I2C
+	select SND_SOC_PCM186X_SPI if SPI_MASTER
 	select SND_SOC_PCM3008
 	select SND_SOC_PCM3168A_I2C if I2C
 	select SND_SOC_PCM3168A_SPI if SPI_MASTER
@@ -661,6 +663,21 @@ config SND_SOC_PCM179X_SPI
 	  Enable support for Texas Instruments PCM179x CODEC.
 	  Select this if your PCM179x is connected via an SPI bus.
 
+config SND_SOC_PCM186X
+	tristate
+
+config SND_SOC_PCM186X_I2C
+	tristate "Texas Instruments PCM186x CODECs - I2C"
+	depends on I2C
+	select SND_SOC_PCM186X
+	select REGMAP_I2C
+
+config SND_SOC_PCM186X_SPI
+	tristate "Texas Instruments PCM186x CODECs - SPI"
+	depends on SPI_MASTER
+	select SND_SOC_PCM186X
+	select REGMAP_SPI
+
 config SND_SOC_PCM3008
        tristate
 
diff --git a/sound/soc/codecs/Makefile b/sound/soc/codecs/Makefile
index 0001069ce2a7..146e48a60098 100644
--- a/sound/soc/codecs/Makefile
+++ b/sound/soc/codecs/Makefile
@@ -105,6 +105,9 @@ snd-soc-pcm1681-objs := pcm1681.o
 snd-soc-pcm179x-codec-objs := pcm179x.o
 snd-soc-pcm179x-i2c-objs := pcm179x-i2c.o
 snd-soc-pcm179x-spi-objs := pcm179x-spi.o
+snd-soc-pcm186x-objs := pcm186x.o
+snd-soc-pcm186x-i2c-objs := pcm186x-i2c.o
+snd-soc-pcm186x-spi-objs := pcm186x-spi.o
 snd-soc-pcm3008-objs := pcm3008.o
 snd-soc-pcm3168a-objs := pcm3168a.o
 snd-soc-pcm3168a-i2c-objs := pcm3168a-i2c.o
@@ -345,6 +348,9 @@ obj-$(CONFIG_SND_SOC_PCM1681)	+= snd-soc-pcm1681.o
 obj-$(CONFIG_SND_SOC_PCM179X)	+= snd-soc-pcm179x-codec.o
 obj-$(CONFIG_SND_SOC_PCM179X_I2C)	+= snd-soc-pcm179x-i2c.o
 obj-$(CONFIG_SND_SOC_PCM179X_SPI)	+= snd-soc-pcm179x-spi.o
+obj-$(CONFIG_SND_SOC_PCM186X)	+= snd-soc-pcm186x.o
+obj-$(CONFIG_SND_SOC_PCM186X_I2C)	+= snd-soc-pcm186x-i2c.o
+obj-$(CONFIG_SND_SOC_PCM186X_SPI)	+= snd-soc-pcm186x-spi.o
 obj-$(CONFIG_SND_SOC_PCM3008)	+= snd-soc-pcm3008.o
 obj-$(CONFIG_SND_SOC_PCM3168A)	+= snd-soc-pcm3168a.o
 obj-$(CONFIG_SND_SOC_PCM3168A_I2C)	+= snd-soc-pcm3168a-i2c.o
diff --git a/sound/soc/codecs/pcm186x-i2c.c b/sound/soc/codecs/pcm186x-i2c.c
new file mode 100644
index 000000000000..6310325043a1
--- /dev/null
+++ b/sound/soc/codecs/pcm186x-i2c.c
@@ -0,0 +1,69 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Texas Instruments PCM186x Universal Audio ADC - I2C
+ *
+ * Copyright (C) 2015-2017 Texas Instruments Incorporated - http://www.ti.com
+ *	Andreas Dannenberg <dannenberg@ti.com>
+ *	Andrew F. Davis <afd@ti.com>
+ */
+
+#include <linux/init.h>
+#include <linux/module.h>
+#include <linux/i2c.h>
+
+#include "pcm186x.h"
+
+static const struct of_device_id pcm186x_of_match[] = {
+	{ .compatible = "ti,pcm1862", .data = (void *)PCM1862 },
+	{ .compatible = "ti,pcm1863", .data = (void *)PCM1863 },
+	{ .compatible = "ti,pcm1864", .data = (void *)PCM1864 },
+	{ .compatible = "ti,pcm1865", .data = (void *)PCM1865 },
+	{ }
+};
+MODULE_DEVICE_TABLE(of, pcm186x_of_match);
+
+static int pcm186x_i2c_probe(struct i2c_client *i2c,
+			     const struct i2c_device_id *id)
+{
+	const enum pcm186x_type type = (enum pcm186x_type)id->driver_data;
+	int irq = i2c->irq;
+	struct regmap *regmap;
+
+	regmap = devm_regmap_init_i2c(i2c, &pcm186x_regmap);
+	if (IS_ERR(regmap))
+		return PTR_ERR(regmap);
+
+	return pcm186x_probe(&i2c->dev, type, irq, regmap);
+}
+
+static int pcm186x_i2c_remove(struct i2c_client *i2c)
+{
+	pcm186x_remove(&i2c->dev);
+	return 0;
+}
+
+static const struct i2c_device_id pcm186x_i2c_id[] = {
+	{ "pcm1862", PCM1862 },
+	{ "pcm1863", PCM1863 },
+	{ "pcm1864", PCM1864 },
+	{ "pcm1865", PCM1865 },
+	{ }
+};
+MODULE_DEVICE_TABLE(i2c, pcm186x_i2c_id);
+
+static struct i2c_driver pcm186x_i2c_driver = {
+	.probe		= pcm186x_i2c_probe,
+	.remove		= pcm186x_i2c_remove,
+	.id_table	= pcm186x_i2c_id,
+	.driver		= {
+		.name	= "pcm186x",
+		.of_match_table = pcm186x_of_match,
+		.pm     = &pcm186x_pm_ops,
+	},
+};
+module_i2c_driver(pcm186x_i2c_driver);
+
+MODULE_AUTHOR("Andreas Dannenberg <dannenberg@ti.com>");
+MODULE_AUTHOR("Andrew F. Davis <afd@ti.com>");
+MODULE_DESCRIPTION("PCM186x Universal Audio ADC I2C Interface Driver");
+MODULE_LICENSE("GPL v2");
diff --git a/sound/soc/codecs/pcm186x-spi.c b/sound/soc/codecs/pcm186x-spi.c
new file mode 100644
index 000000000000..2b4a5351aeff
--- /dev/null
+++ b/sound/soc/codecs/pcm186x-spi.c
@@ -0,0 +1,69 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Texas Instruments PCM186x Universal Audio ADC - SPI
+ *
+ * Copyright (C) 2015-2017 Texas Instruments Incorporated - http://www.ti.com
+ *	Andreas Dannenberg <dannenberg@ti.com>
+ *	Andrew F. Davis <afd@ti.com>
+ */
+
+#include <linux/init.h>
+#include <linux/module.h>
+#include <linux/spi/spi.h>
+
+#include "pcm186x.h"
+
+static const struct of_device_id pcm186x_of_match[] = {
+	{ .compatible = "ti,pcm1862", .data = (void *)PCM1862 },
+	{ .compatible = "ti,pcm1863", .data = (void *)PCM1863 },
+	{ .compatible = "ti,pcm1864", .data = (void *)PCM1864 },
+	{ .compatible = "ti,pcm1865", .data = (void *)PCM1865 },
+	{ }
+};
+MODULE_DEVICE_TABLE(of, pcm186x_of_match);
+
+static int pcm186x_spi_probe(struct spi_device *spi)
+{
+	const enum pcm186x_type type =
+			 (enum pcm186x_type)spi_get_device_id(spi)->driver_data;
+	int irq = spi->irq;
+	struct regmap *regmap;
+
+	regmap = devm_regmap_init_spi(spi, &pcm186x_regmap);
+	if (IS_ERR(regmap))
+		return PTR_ERR(regmap);
+
+	return pcm186x_probe(&spi->dev, type, irq, regmap);
+}
+
+static int pcm186x_spi_remove(struct spi_device *spi)
+{
+	pcm186x_remove(&spi->dev);
+	return 0;
+}
+
+static const struct spi_device_id pcm186x_spi_id[] = {
+	{ "pcm1862", PCM1862 },
+	{ "pcm1863", PCM1863 },
+	{ "pcm1864", PCM1864 },
+	{ "pcm1865", PCM1865 },
+	{ }
+};
+MODULE_DEVICE_TABLE(spi, pcm186x_spi_id);
+
+static struct spi_driver pcm186x_spi_driver = {
+	.probe		= pcm186x_spi_probe,
+	.remove		= pcm186x_spi_remove,
+	.id_table	= pcm186x_spi_id,
+	.driver		= {
+		.name	= "pcm186x",
+		.of_match_table = pcm186x_of_match,
+		.pm     = &pcm186x_pm_ops,
+	},
+};
+module_spi_driver(pcm186x_spi_driver);
+
+MODULE_AUTHOR("Andreas Dannenberg <dannenberg@ti.com>");
+MODULE_AUTHOR("Andrew F. Davis <afd@ti.com>");
+MODULE_DESCRIPTION("PCM186x Universal Audio ADC SPI Interface Driver");
+MODULE_LICENSE("GPL v2");
diff --git a/sound/soc/codecs/pcm186x.c b/sound/soc/codecs/pcm186x.c
new file mode 100644
index 000000000000..0553ac176c37
--- /dev/null
+++ b/sound/soc/codecs/pcm186x.c
@@ -0,0 +1,773 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Texas Instruments PCM186x Universal Audio ADC
+ *
+ * Copyright (C) 2015-2017 Texas Instruments Incorporated - http://www.ti.com
+ *	Andreas Dannenberg <dannenberg@ti.com>
+ *	Andrew F. Davis <afd@ti.com>
+ */
+
+#include <linux/module.h>
+#include <linux/moduleparam.h>
+#include <linux/init.h>
+#include <linux/delay.h>
+#include <linux/pm.h>
+#include <linux/pm_runtime.h>
+#include <linux/regulator/consumer.h>
+#include <linux/regmap.h>
+#include <linux/slab.h>
+#include <sound/core.h>
+#include <sound/pcm.h>
+#include <sound/pcm_params.h>
+#include <sound/soc.h>
+#include <sound/jack.h>
+#include <sound/initval.h>
+#include <sound/tlv.h>
+
+#include "pcm186x.h"
+
+static const char * const pcm186x_supply_names[] = {
+	"avdd",		/* Analog power supply. Connect to 3.3-V supply. */
+	"dvdd",		/* Digital power supply. Connect to 3.3-V supply. */
+	"iovdd",	/* I/O power supply. Connect to 3.3-V or 1.8-V. */
+};
+#define PCM186x_NUM_SUPPLIES ARRAY_SIZE(pcm186x_supply_names)
+
+struct pcm186x_priv {
+	struct regmap *regmap;
+	struct regulator_bulk_data supplies[PCM186x_NUM_SUPPLIES];
+	unsigned int sysclk;
+	unsigned int tdm_offset;
+	bool is_tdm_mode;
+	bool is_master_mode;
+};
+
+static const DECLARE_TLV_DB_SCALE(pcm186x_pga_tlv, -1200, 4000, 50);
+
+static const struct snd_kcontrol_new pcm1863_snd_controls[] = {
+	SOC_DOUBLE_R_S_TLV("ADC Capture Volume", PCM186X_PGA_VAL_CH1_L,
+			   PCM186X_PGA_VAL_CH1_R, 0, -24, 80, 7, 0,
+			   pcm186x_pga_tlv),
+};
+
+static const struct snd_kcontrol_new pcm1865_snd_controls[] = {
+	SOC_DOUBLE_R_S_TLV("ADC1 Capture Volume", PCM186X_PGA_VAL_CH1_L,
+			   PCM186X_PGA_VAL_CH1_R, 0, -24, 80, 7, 0,
+			   pcm186x_pga_tlv),
+	SOC_DOUBLE_R_S_TLV("ADC2 Capture Volume", PCM186X_PGA_VAL_CH2_L,
+			   PCM186X_PGA_VAL_CH2_R, 0, -24, 80, 7, 0,
+			   pcm186x_pga_tlv),
+};
+
+const unsigned int pcm186x_adc_input_channel_sel_value[] = {
+	0x00, 0x01, 0x02, 0x03, 0x04, 0x05, 0x06, 0x07,
+	0x08, 0x09, 0x0a, 0x0b, 0x0c, 0x0d, 0x0e, 0x0f,
+	0x10, 0x20, 0x30
+};
+
+static const char * const pcm186x_adcl_input_channel_sel_text[] = {
+	"No Select",
+	"VINL1[SE]",					/* Default for ADC1L */
+	"VINL2[SE]",					/* Default for ADC2L */
+	"VINL2[SE] + VINL1[SE]",
+	"VINL3[SE]",
+	"VINL3[SE] + VINL1[SE]",
+	"VINL3[SE] + VINL2[SE]",
+	"VINL3[SE] + VINL2[SE] + VINL1[SE]",
+	"VINL4[SE]",
+	"VINL4[SE] + VINL1[SE]",
+	"VINL4[SE] + VINL2[SE]",
+	"VINL4[SE] + VINL2[SE] + VINL1[SE]",
+	"VINL4[SE] + VINL3[SE]",
+	"VINL4[SE] + VINL3[SE] + VINL1[SE]",
+	"VINL4[SE] + VINL3[SE] + VINL2[SE]",
+	"VINL4[SE] + VINL3[SE] + VINL2[SE] + VINL1[SE]",
+	"{VIN1P, VIN1M}[DIFF]",
+	"{VIN4P, VIN4M}[DIFF]",
+	"{VIN1P, VIN1M}[DIFF] + {VIN4P, VIN4M}[DIFF]"
+};
+
+static const char * const pcm186x_adcr_input_channel_sel_text[] = {
+	"No Select",
+	"VINR1[SE]",					/* Default for ADC1R */
+	"VINR2[SE]",					/* Default for ADC2R */
+	"VINR2[SE] + VINR1[SE]",
+	"VINR3[SE]",
+	"VINR3[SE] + VINR1[SE]",
+	"VINR3[SE] + VINR2[SE]",
+	"VINR3[SE] + VINR2[SE] + VINR1[SE]",
+	"VINR4[SE]",
+	"VINR4[SE] + VINR1[SE]",
+	"VINR4[SE] + VINR2[SE]",
+	"VINR4[SE] + VINR2[SE] + VINR1[SE]",
+	"VINR4[SE] + VINR3[SE]",
+	"VINR4[SE] + VINR3[SE] + VINR1[SE]",
+	"VINR4[SE] + VINR3[SE] + VINR2[SE]",
+	"VINR4[SE] + VINR3[SE] + VINR2[SE] + VINR1[SE]",
+	"{VIN2P, VIN2M}[DIFF]",
+	"{VIN3P, VIN3M}[DIFF]",
+	"{VIN2P, VIN2M}[DIFF] + {VIN3P, VIN3M}[DIFF]"
+};
+
+static const struct soc_enum pcm186x_adc_input_channel_sel[] = {
+	SOC_VALUE_ENUM_SINGLE(PCM186X_ADC1_INPUT_SEL_L, 0,
+			      PCM186X_ADC_INPUT_SEL_MASK,
+			      ARRAY_SIZE(pcm186x_adcl_input_channel_sel_text),
+			      pcm186x_adcl_input_channel_sel_text,
+			      pcm186x_adc_input_channel_sel_value),
+	SOC_VALUE_ENUM_SINGLE(PCM186X_ADC1_INPUT_SEL_R, 0,
+			      PCM186X_ADC_INPUT_SEL_MASK,
+			      ARRAY_SIZE(pcm186x_adcr_input_channel_sel_text),
+			      pcm186x_adcr_input_channel_sel_text,
+			      pcm186x_adc_input_channel_sel_value),
+	SOC_VALUE_ENUM_SINGLE(PCM186X_ADC2_INPUT_SEL_L, 0,
+			      PCM186X_ADC_INPUT_SEL_MASK,
+			      ARRAY_SIZE(pcm186x_adcl_input_channel_sel_text),
+			      pcm186x_adcl_input_channel_sel_text,
+			      pcm186x_adc_input_channel_sel_value),
+	SOC_VALUE_ENUM_SINGLE(PCM186X_ADC2_INPUT_SEL_R, 0,
+			      PCM186X_ADC_INPUT_SEL_MASK,
+			      ARRAY_SIZE(pcm186x_adcr_input_channel_sel_text),
+			      pcm186x_adcr_input_channel_sel_text,
+			      pcm186x_adc_input_channel_sel_value),
+};
+
+static const struct snd_kcontrol_new pcm186x_adc_mux_controls[] = {
+	SOC_DAPM_ENUM("ADC1 Left Input", pcm186x_adc_input_channel_sel[0]),
+	SOC_DAPM_ENUM("ADC1 Right Input", pcm186x_adc_input_channel_sel[1]),
+	SOC_DAPM_ENUM("ADC2 Left Input", pcm186x_adc_input_channel_sel[2]),
+	SOC_DAPM_ENUM("ADC2 Right Input", pcm186x_adc_input_channel_sel[3]),
+};
+
+static const struct snd_soc_dapm_widget pcm1863_dapm_widgets[] = {
+	SND_SOC_DAPM_INPUT("VINL1"),
+	SND_SOC_DAPM_INPUT("VINR1"),
+	SND_SOC_DAPM_INPUT("VINL2"),
+	SND_SOC_DAPM_INPUT("VINR2"),
+	SND_SOC_DAPM_INPUT("VINL3"),
+	SND_SOC_DAPM_INPUT("VINR3"),
+	SND_SOC_DAPM_INPUT("VINL4"),
+	SND_SOC_DAPM_INPUT("VINR4"),
+
+	SND_SOC_DAPM_MUX("ADC Left Capture Source", SND_SOC_NOPM, 0, 0,
+			 &pcm186x_adc_mux_controls[0]),
+	SND_SOC_DAPM_MUX("ADC Right Capture Source", SND_SOC_NOPM, 0, 0,
+			 &pcm186x_adc_mux_controls[1]),
+
+	/*
+	 * Put the codec into SLEEP mode when not in use, allowing the
+	 * Energysense mechanism to operate.
+	 */
+	SND_SOC_DAPM_ADC("ADC", "HiFi Capture", PCM186X_POWER_CTRL, 1,  0),
+};
+
+static const struct snd_soc_dapm_widget pcm1865_dapm_widgets[] = {
+	SND_SOC_DAPM_INPUT("VINL1"),
+	SND_SOC_DAPM_INPUT("VINR1"),
+	SND_SOC_DAPM_INPUT("VINL2"),
+	SND_SOC_DAPM_INPUT("VINR2"),
+	SND_SOC_DAPM_INPUT("VINL3"),
+	SND_SOC_DAPM_INPUT("VINR3"),
+	SND_SOC_DAPM_INPUT("VINL4"),
+	SND_SOC_DAPM_INPUT("VINR4"),
+
+	SND_SOC_DAPM_MUX("ADC1 Left Capture Source", SND_SOC_NOPM, 0, 0,
+			 &pcm186x_adc_mux_controls[0]),
+	SND_SOC_DAPM_MUX("ADC1 Right Capture Source", SND_SOC_NOPM, 0, 0,
+			 &pcm186x_adc_mux_controls[1]),
+	SND_SOC_DAPM_MUX("ADC2 Left Capture Source", SND_SOC_NOPM, 0, 0,
+			 &pcm186x_adc_mux_controls[2]),
+	SND_SOC_DAPM_MUX("ADC2 Right Capture Source", SND_SOC_NOPM, 0, 0,
+			 &pcm186x_adc_mux_controls[3]),
+
+	/*
+	 * Put the codec into SLEEP mode when not in use, allowing the
+	 * Energysense mechanism to operate.
+	 */
+	SND_SOC_DAPM_ADC("ADC1", "HiFi Capture 1", PCM186X_POWER_CTRL, 1,  0),
+	SND_SOC_DAPM_ADC("ADC2", "HiFi Capture 2", PCM186X_POWER_CTRL, 1,  0),
+};
+
+static const struct snd_soc_dapm_route pcm1863_dapm_routes[] = {
+	{ "ADC Left Capture Source", NULL, "VINL1" },
+	{ "ADC Left Capture Source", NULL, "VINR1" },
+	{ "ADC Left Capture Source", NULL, "VINL2" },
+	{ "ADC Left Capture Source", NULL, "VINR2" },
+	{ "ADC Left Capture Source", NULL, "VINL3" },
+	{ "ADC Left Capture Source", NULL, "VINR3" },
+	{ "ADC Left Capture Source", NULL, "VINL4" },
+	{ "ADC Left Capture Source", NULL, "VINR4" },
+
+	{ "ADC", NULL, "ADC Left Capture Source" },
+
+	{ "ADC Right Capture Source", NULL, "VINL1" },
+	{ "ADC Right Capture Source", NULL, "VINR1" },
+	{ "ADC Right Capture Source", NULL, "VINL2" },
+	{ "ADC Right Capture Source", NULL, "VINR2" },
+	{ "ADC Right Capture Source", NULL, "VINL3" },
+	{ "ADC Right Capture Source", NULL, "VINR3" },
+	{ "ADC Right Capture Source", NULL, "VINL4" },
+	{ "ADC Right Capture Source", NULL, "VINR4" },
+
+	{ "ADC", NULL, "ADC Right Capture Source" },
+};
+
+static const struct snd_soc_dapm_route pcm1865_dapm_routes[] = {
+	{ "ADC1 Left Capture Source", NULL, "VINL1" },
+	{ "ADC1 Left Capture Source", NULL, "VINR1" },
+	{ "ADC1 Left Capture Source", NULL, "VINL2" },
+	{ "ADC1 Left Capture Source", NULL, "VINR2" },
+	{ "ADC1 Left Capture Source", NULL, "VINL3" },
+	{ "ADC1 Left Capture Source", NULL, "VINR3" },
+	{ "ADC1 Left Capture Source", NULL, "VINL4" },
+	{ "ADC1 Left Capture Source", NULL, "VINR4" },
+
+	{ "ADC1", NULL, "ADC1 Left Capture Source" },
+
+	{ "ADC1 Right Capture Source", NULL, "VINL1" },
+	{ "ADC1 Right Capture Source", NULL, "VINR1" },
+	{ "ADC1 Right Capture Source", NULL, "VINL2" },
+	{ "ADC1 Right Capture Source", NULL, "VINR2" },
+	{ "ADC1 Right Capture Source", NULL, "VINL3" },
+	{ "ADC1 Right Capture Source", NULL, "VINR3" },
+	{ "ADC1 Right Capture Source", NULL, "VINL4" },
+	{ "ADC1 Right Capture Source", NULL, "VINR4" },
+
+	{ "ADC1", NULL, "ADC1 Right Capture Source" },
+
+	{ "ADC2 Left Capture Source", NULL, "VINL1" },
+	{ "ADC2 Left Capture Source", NULL, "VINR1" },
+	{ "ADC2 Left Capture Source", NULL, "VINL2" },
+	{ "ADC2 Left Capture Source", NULL, "VINR2" },
+	{ "ADC2 Left Capture Source", NULL, "VINL3" },
+	{ "ADC2 Left Capture Source", NULL, "VINR3" },
+	{ "ADC2 Left Capture Source", NULL, "VINL4" },
+	{ "ADC2 Left Capture Source", NULL, "VINR4" },
+
+	{ "ADC2", NULL, "ADC2 Left Capture Source" },
+
+	{ "ADC2 Right Capture Source", NULL, "VINL1" },
+	{ "ADC2 Right Capture Source", NULL, "VINR1" },
+	{ "ADC2 Right Capture Source", NULL, "VINL2" },
+	{ "ADC2 Right Capture Source", NULL, "VINR2" },
+	{ "ADC2 Right Capture Source", NULL, "VINL3" },
+	{ "ADC2 Right Capture Source", NULL, "VINR3" },
+	{ "ADC2 Right Capture Source", NULL, "VINL4" },
+	{ "ADC2 Right Capture Source", NULL, "VINR4" },
+
+	{ "ADC2", NULL, "ADC2 Right Capture Source" },
+};
+
+static int pcm186x_hw_params(struct snd_pcm_substream *substream,
+			     struct snd_pcm_hw_params *params,
+			     struct snd_soc_dai *dai)
+{
+	struct snd_soc_codec *codec = dai->codec;
+
+	struct pcm186x_priv *priv = snd_soc_codec_get_drvdata(codec);
+	unsigned int rate = params_rate(params);
+	unsigned int format = params_format(params);
+	unsigned int width = params_width(params);
+	unsigned int channels = params_channels(params);
+	unsigned int div_lrck;
+	unsigned int div_bck;
+	u8 tdm_tx_sel = 0;
+	u8 pcm_cfg = 0;
+	int ret;
+
+	dev_dbg(codec->dev, "%s() rate=%u format=0x%x width=%u channels=%u\n",
+		__func__, rate, format, width, channels);
+
+	switch (width) {
+	case 16:
+		pcm_cfg = PCM186X_PCM_CFG_RX_WLEN_16 <<
+			  PCM186X_PCM_CFG_RX_WLEN_SHIFT |
+			  PCM186X_PCM_CFG_TX_WLEN_16 <<
+			  PCM186X_PCM_CFG_TX_WLEN_SHIFT;
+		break;
+	case 20:
+		pcm_cfg = PCM186X_PCM_CFG_RX_WLEN_20 <<
+			  PCM186X_PCM_CFG_RX_WLEN_SHIFT |
+			  PCM186X_PCM_CFG_TX_WLEN_20 <<
+			  PCM186X_PCM_CFG_TX_WLEN_SHIFT;
+		break;
+	case 24:
+		pcm_cfg = PCM186X_PCM_CFG_RX_WLEN_24 <<
+			  PCM186X_PCM_CFG_RX_WLEN_SHIFT |
+			  PCM186X_PCM_CFG_TX_WLEN_24 <<
+			  PCM186X_PCM_CFG_TX_WLEN_SHIFT;
+		break;
+	case 32:
+		pcm_cfg = PCM186X_PCM_CFG_RX_WLEN_32 <<
+			  PCM186X_PCM_CFG_RX_WLEN_SHIFT |
+			  PCM186X_PCM_CFG_TX_WLEN_32 <<
+			  PCM186X_PCM_CFG_TX_WLEN_SHIFT;
+		break;
+	default:
+		return -EINVAL;
+	}
+
+	snd_soc_update_bits(codec, PCM186X_PCM_CFG,
+			    PCM186X_PCM_CFG_RX_WLEN_MASK |
+			    PCM186X_PCM_CFG_TX_WLEN_MASK,
+			    pcm_cfg);
+
+	div_lrck = width * channels;
+
+	if (priv->is_tdm_mode) {
+		/* Select TDM transmission data */
+		switch (channels) {
+		case 2:
+			tdm_tx_sel = PCM186X_TDM_TX_SEL_2CH;
+			break;
+		case 4:
+			tdm_tx_sel = PCM186X_TDM_TX_SEL_4CH;
+			break;
+		case 6:
+			tdm_tx_sel = PCM186X_TDM_TX_SEL_6CH;
+			break;
+		default:
+			return -EINVAL;
+		}
+
+		snd_soc_update_bits(codec, PCM186X_TDM_TX_SEL,
+				    PCM186X_TDM_TX_SEL_MASK, tdm_tx_sel);
+
+		/* In DSP/TDM mode, the LRCLK divider must be 256 */
+		div_lrck = 256;
+
+		/* Configure 1/256 duty cycle for LRCK */
+		snd_soc_update_bits(codec, PCM186X_PCM_CFG,
+				    PCM186X_PCM_CFG_TDM_LRCK_MODE,
+				    PCM186X_PCM_CFG_TDM_LRCK_MODE);
+	}
+
+	/* Only configure clock dividers in master mode. */
+	if (priv->is_master_mode) {
+		div_bck = priv->sysclk / (div_lrck * rate);
+
+		dev_dbg(codec->dev,
+			"%s() master_clk=%u div_bck=%u div_lrck=%u\n",
+			__func__, priv->sysclk, div_bck, div_lrck);
+
+		snd_soc_write(codec, PCM186X_BCK_DIV, div_bck - 1);
+		snd_soc_write(codec, PCM186X_LRK_DIV, div_lrck - 1);
+	}
+
+	return 0;
+}
+
+static int pcm186x_set_fmt(struct snd_soc_dai *dai, unsigned int format)
+{
+	struct snd_soc_codec *codec = dai->codec;
+	struct pcm186x_priv *priv = snd_soc_codec_get_drvdata(codec);
+	u8 clk_ctrl = 0;
+	u8 pcm_cfg = 0;
+
+	dev_dbg(codec->dev, "%s() format=0x%x\n", __func__, format);
+
+	/* set master/slave audio interface */
+	switch (format & SND_SOC_DAIFMT_MASTER_MASK) {
+	case SND_SOC_DAIFMT_CBM_CFM:
+		if (!priv->sysclk) {
+			dev_err(codec->dev, "operating in master mode requires sysclock to be configured\n");
+			return -EINVAL;
+		}
+		clk_ctrl |= PCM186X_CLK_CTRL_MST_MODE;
+		priv->is_master_mode = true;
+		break;
+	case SND_SOC_DAIFMT_CBS_CFS:
+		priv->is_master_mode = false;
+		break;
+	default:
+		dev_err(codec->dev, "Invalid DAI master/slave interface\n");
+		return -EINVAL;
+	}
+
+	/* set interface polarity */
+	switch (format & SND_SOC_DAIFMT_INV_MASK) {
+	case SND_SOC_DAIFMT_NB_NF:
+		break;
+	default:
+		dev_err(codec->dev, "Inverted DAI clocks not supported\n");
+		return -EINVAL;
+	}
+
+	/* set interface format */
+	switch (format & SND_SOC_DAIFMT_FORMAT_MASK) {
+	case SND_SOC_DAIFMT_I2S:
+		pcm_cfg = PCM186X_PCM_CFG_FMT_I2S;
+		break;
+	case SND_SOC_DAIFMT_LEFT_J:
+		pcm_cfg = PCM186X_PCM_CFG_FMT_LEFTJ;
+		break;
+	case SND_SOC_DAIFMT_DSP_A:
+		priv->tdm_offset += 1;
+		/* Fall through... DSP_A uses the same basic config as DSP_B
+		 * except we need to shift the TDM output by one BCK cycle
+		 */
+	case SND_SOC_DAIFMT_DSP_B:
+		priv->is_tdm_mode = true;
+		pcm_cfg = PCM186X_PCM_CFG_FMT_TDM;
+		break;
+	default:
+		return -EINVAL;
+	}
+
+	snd_soc_update_bits(codec, PCM186X_CLK_CTRL,
+			    PCM186X_CLK_CTRL_MST_MODE, clk_ctrl);
+
+	snd_soc_write(codec, PCM186X_TDM_TX_OFFSET, priv->tdm_offset);
+
+	snd_soc_update_bits(codec, PCM186X_PCM_CFG,
+			    PCM186X_PCM_CFG_FMT_MASK, pcm_cfg);
+
+	return 0;
+}
+
+static int pcm186x_set_tdm_slot(struct snd_soc_dai *dai, unsigned int tx_mask,
+				unsigned int rx_mask, int slots, int slot_width)
+{
+	struct snd_soc_codec *codec = dai->codec;
+	struct pcm186x_priv *priv = snd_soc_codec_get_drvdata(codec);
+	unsigned int first_slot, last_slot, tdm_offset;
+
+	dev_dbg(codec->dev,
+		"%s() tx_mask=0x%x rx_mask=0x%x slots=%d slot_width=%d\n",
+		__func__, tx_mask, rx_mask, slots, slot_width);
+
+	if (!tx_mask) {
+		dev_err(codec->dev, "tdm tx mask must not be 0\n");
+		return -EINVAL;
+	}
+
+	first_slot = __ffs(tx_mask);
+	last_slot = __fls(tx_mask);
+
+	if (last_slot - first_slot != hweight32(tx_mask) - 1) {
+		dev_err(codec->dev, "tdm tx mask must be contiguous\n");
+		return -EINVAL;
+	}
+
+	tdm_offset = first_slot * slot_width;
+
+	if (tdm_offset > 255) {
+		dev_err(codec->dev, "tdm tx slot selection out of bounds\n");
+		return -EINVAL;
+	}
+
+	priv->tdm_offset = tdm_offset;
+
+	return 0;
+}
+
+static int pcm186x_set_dai_sysclk(struct snd_soc_dai *dai, int clk_id,
+				  unsigned int freq, int dir)
+{
+	struct snd_soc_codec *codec = dai->codec;
+	struct pcm186x_priv *priv = snd_soc_codec_get_drvdata(codec);
+
+	dev_dbg(codec->dev, "%s() clk_id=%d freq=%u dir=%d\n",
+		__func__, clk_id, freq, dir);
+
+	priv->sysclk = freq;
+
+	return 0;
+}
+
+const struct snd_soc_dai_ops pcm186x_dai_ops = {
+	.set_sysclk = pcm186x_set_dai_sysclk,
+	.set_tdm_slot = pcm186x_set_tdm_slot,
+	.set_fmt = pcm186x_set_fmt,
+	.hw_params = pcm186x_hw_params,
+};
+
+static struct snd_soc_dai_driver pcm1863_dai = {
+	.name = "pcm1863-aif",
+	.capture = {
+		 .stream_name = "Capture",
+		 .channels_min = 1,
+		 .channels_max = 2,
+		 .rates = PCM186X_RATES,
+		 .formats = PCM186X_FORMATS,
+	 },
+	.ops = &pcm186x_dai_ops,
+};
+
+static struct snd_soc_dai_driver pcm1865_dai = {
+	.name = "pcm1865-aif",
+	.capture = {
+		 .stream_name = "Capture",
+		 .channels_min = 1,
+		 .channels_max = 4,
+		 .rates = PCM186X_RATES,
+		 .formats = PCM186X_FORMATS,
+	 },
+	.ops = &pcm186x_dai_ops,
+};
+
+static int pcm186x_power_on(struct snd_soc_codec *codec)
+{
+	struct pcm186x_priv *priv = snd_soc_codec_get_drvdata(codec);
+	int ret = 0;
+
+	ret = regulator_bulk_enable(ARRAY_SIZE(priv->supplies),
+				    priv->supplies);
+	if (ret)
+		return ret;
+
+	regcache_cache_only(priv->regmap, false);
+	ret = regcache_sync(priv->regmap);
+	if (ret != 0) {
+		dev_err(codec->dev, "Failed to restore cache\n");
+		regcache_cache_only(priv->regmap, true);
+		regulator_bulk_disable(ARRAY_SIZE(priv->supplies),
+				       priv->supplies);
+		return ret;
+	}
+
+	return 0;
+}
+
+static int pcm186x_power_off(struct snd_soc_codec *codec)
+{
+	struct pcm186x_priv *priv = snd_soc_codec_get_drvdata(codec);
+	int ret;
+
+	regcache_cache_only(priv->regmap, true);
+	ret = regulator_bulk_disable(ARRAY_SIZE(priv->supplies),
+				     priv->supplies);
+	if (ret)
+		return ret;
+
+	return 0;
+}
+
+static int pcm186x_set_bias_level(struct snd_soc_codec *codec,
+				  enum snd_soc_bias_level level)
+{
+	dev_dbg(codec->dev, "## %s: %d -> %d\n", __func__,
+		snd_soc_codec_get_bias_level(codec), level);
+
+	switch (level) {
+	case SND_SOC_BIAS_ON:
+		break;
+	case SND_SOC_BIAS_PREPARE:
+		break;
+	case SND_SOC_BIAS_STANDBY:
+		pcm186x_power_on(codec);
+		break;
+	case SND_SOC_BIAS_OFF:
+		pcm186x_power_off(codec);
+		break;
+	}
+
+	return 0;
+}
+
+static struct snd_soc_codec_driver soc_codec_dev_pcm1863 = {
+	.set_bias_level = pcm186x_set_bias_level,
+
+	.component_driver = {
+		.controls = pcm1863_snd_controls,
+		.num_controls = ARRAY_SIZE(pcm1863_snd_controls),
+		.dapm_widgets = pcm1863_dapm_widgets,
+		.num_dapm_widgets = ARRAY_SIZE(pcm1863_dapm_widgets),
+		.dapm_routes = pcm1863_dapm_routes,
+		.num_dapm_routes = ARRAY_SIZE(pcm1863_dapm_routes),
+	},
+};
+
+static struct snd_soc_codec_driver soc_codec_dev_pcm1865 = {
+	.set_bias_level = pcm186x_set_bias_level,
+
+	.component_driver = {
+		.controls = pcm1865_snd_controls,
+		.num_controls = ARRAY_SIZE(pcm1865_snd_controls),
+		.dapm_widgets = pcm1865_dapm_widgets,
+		.num_dapm_widgets = ARRAY_SIZE(pcm1865_dapm_widgets),
+		.dapm_routes = pcm1865_dapm_routes,
+		.num_dapm_routes = ARRAY_SIZE(pcm1865_dapm_routes),
+	},
+};
+
+static bool pcm186x_volatile(struct device *dev, unsigned int reg)
+{
+	switch (reg) {
+	case PCM186X_PAGE:
+	case PCM186X_DEVICE_STATUS:
+	case PCM186X_FSAMPLE_STATUS:
+	case PCM186X_DIV_STATUS:
+	case PCM186X_CLK_STATUS:
+	case PCM186X_SUPPLY_STATUS:
+	case PCM186X_MMAP_STAT_CTRL:
+	case PCM186X_MMAP_ADDRESS:
+		return true;
+	}
+
+	return false;
+}
+
+/*
+ * The PCM186x's page register is located on every page, allowing to program it
+ * without having to switch pages. Take advantage of this by defining the range
+ * such to have this register located inside the data window.
+ */
+static const struct regmap_range_cfg pcm186x_range = {
+	.name = "Pages",
+	.range_max = PCM186X_MAX_REGISTER,
+	.selector_reg = PCM186X_PAGE,
+	.selector_mask = 0xff,
+	.window_len = PCM186X_PAGE_LEN,
+};
+
+const struct regmap_config pcm186x_regmap = {
+	.reg_bits = 8,
+	.val_bits = 8,
+
+	.volatile_reg = pcm186x_volatile,
+
+	.ranges = &pcm186x_range,
+	.num_ranges = 1,
+
+	.max_register = PCM186X_MAX_REGISTER,
+
+	.cache_type = REGCACHE_RBTREE,
+};
+EXPORT_SYMBOL_GPL(pcm186x_regmap);
+
+int pcm186x_probe(struct device *dev, enum pcm186x_type type, int irq,
+		  struct regmap *regmap)
+{
+	struct pcm186x_priv *priv;
+	int i, ret;
+
+	priv = devm_kzalloc(dev, sizeof(struct pcm186x_priv), GFP_KERNEL);
+	if (!priv)
+		return -ENOMEM;
+
+	dev_set_drvdata(dev, priv);
+	priv->regmap = regmap;
+
+	for (i = 0; i < ARRAY_SIZE(priv->supplies); i++)
+		priv->supplies[i].supply = pcm186x_supply_names[i];
+
+	ret = devm_regulator_bulk_get(dev, ARRAY_SIZE(priv->supplies),
+				      priv->supplies);
+	if (ret) {
+		dev_err(dev, "failed to request supplies: %d\n", ret);
+		return ret;
+	}
+
+	ret = regulator_bulk_enable(ARRAY_SIZE(priv->supplies),
+				    priv->supplies);
+	if (ret) {
+		dev_err(dev, "failed enable supplies: %d\n", ret);
+		return ret;
+	}
+
+	/* Reset device registers for a consistent power-on like state */
+	ret = regmap_write(regmap, PCM186X_PAGE, PCM186X_RESET);
+	if (ret) {
+		dev_err(dev, "failed to write device: %d\n", ret);
+		return ret;
+	}
+
+	ret = regulator_bulk_disable(ARRAY_SIZE(priv->supplies),
+				     priv->supplies);
+	if (ret) {
+		dev_err(dev, "failed disable supplies: %d\n", ret);
+		return ret;
+	}
+
+	switch (type) {
+	case PCM1865:
+	case PCM1864:
+		ret = snd_soc_register_codec(dev, &soc_codec_dev_pcm1865,
+					     &pcm1865_dai, 1);
+		break;
+	case PCM1863:
+	case PCM1862:
+		/* Fall through... */
+	default:
+		ret = snd_soc_register_codec(dev, &soc_codec_dev_pcm1863,
+					     &pcm1863_dai, 1);
+	}
+	if (ret != 0) {
+		dev_err(dev, "failed to register CODEC: %d\n", ret);
+		return ret;
+	}
+
+	return 0;
+}
+EXPORT_SYMBOL_GPL(pcm186x_probe);
+
+int pcm186x_remove(struct device *dev)
+{
+	snd_soc_unregister_codec(dev);
+
+	return 0;
+}
+EXPORT_SYMBOL_GPL(pcm186x_remove);
+
+static int __maybe_unused pcm186x_suspend(struct device *dev)
+{
+	struct pcm186x_priv *priv = dev_get_drvdata(dev);
+	int ret;
+
+	ret = regmap_update_bits(priv->regmap, PCM186X_POWER_CTRL,
+				 PCM186X_PWR_CTRL_PWRDN,
+				 PCM186X_PWR_CTRL_PWRDN);
+	if (ret != 0) {
+		dev_err(dev, "failed to write register: %d\n", ret);
+		return ret;
+	}
+
+	ret = regulator_bulk_disable(ARRAY_SIZE(priv->supplies),
+				     priv->supplies);
+	if (ret != 0) {
+		dev_err(dev, "failed to disable supplies: %d\n", ret);
+		return ret;
+	}
+
+	return 0;
+}
+
+static int __maybe_unused pcm186x_resume(struct device *dev)
+{
+	struct pcm186x_priv *priv = dev_get_drvdata(dev);
+	int ret;
+
+	ret = regulator_bulk_enable(ARRAY_SIZE(priv->supplies),
+				    priv->supplies);
+	if (ret != 0) {
+		dev_err(dev, "failed to enable supplies: %d\n", ret);
+		return ret;
+	}
+
+	regcache_cache_only(priv->regmap, false);
+	ret = regcache_sync(priv->regmap);
+	if (ret != 0) {
+		dev_err(dev, "failed to sync cache: %d\n", ret);
+		return ret;
+	}
+
+	ret = regmap_update_bits(priv->regmap, PCM186X_POWER_CTRL,
+				 PCM186X_PWR_CTRL_PWRDN, 0);
+	if (ret != 0) {
+		dev_err(dev, "failed to write register: %d\n", ret);
+		return ret;
+	}
+
+	return 0;
+}
+
+const struct dev_pm_ops pcm186x_pm_ops = {
+	SET_RUNTIME_PM_OPS(pcm186x_suspend, pcm186x_resume, NULL)
+};
+EXPORT_SYMBOL_GPL(pcm186x_pm_ops);
+
+MODULE_AUTHOR("Andreas Dannenberg <dannenberg@ti.com>");
+MODULE_AUTHOR("Andrew F. Davis <afd@ti.com>");
+MODULE_DESCRIPTION("PCM186x Universal Audio ADC driver");
+MODULE_LICENSE("GPL v2");
diff --git a/sound/soc/codecs/pcm186x.h b/sound/soc/codecs/pcm186x.h
new file mode 100644
index 000000000000..64ff11440d32
--- /dev/null
+++ b/sound/soc/codecs/pcm186x.h
@@ -0,0 +1,221 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Texas Instruments PCM186x Universal Audio ADC
+ *
+ * Copyright (C) 2015-2017 Texas Instruments Incorporated - http://www.ti.com
+ *	Andreas Dannenberg <dannenberg@ti.com>
+ *	Andrew F. Davis <afd@ti.com>
+ */
+
+#ifndef _PCM186X_H_
+#define _PCM186X_H_
+
+#include <linux/pm.h>
+#include <linux/regmap.h>
+
+enum pcm186x_type {
+	PCM1862,
+	PCM1863,
+	PCM1864,
+	PCM1865,
+};
+
+#define PCM186X_RATES	SNDRV_PCM_RATE_8000_192000
+#define PCM186X_FORMATS	(SNDRV_PCM_FMTBIT_S16_LE | \
+			 SNDRV_PCM_FMTBIT_S20_3LE |\
+			 SNDRV_PCM_FMTBIT_S24_LE | \
+			 SNDRV_PCM_FMTBIT_S32_LE)
+
+#define PCM186X_PAGE_LEN		0x0100
+#define PCM186X_PAGE_BASE(n)		(PCM186X_PAGE_LEN * n)
+
+/* The page selection register address is the same on all pages */
+#define PCM186X_PAGE			0
+
+/* Register Definitions - Page 0 */
+#define PCM186X_PGA_VAL_CH1_L		(PCM186X_PAGE_BASE(0) +   1)
+#define PCM186X_PGA_VAL_CH1_R		(PCM186X_PAGE_BASE(0) +   2)
+#define PCM186X_PGA_VAL_CH2_L		(PCM186X_PAGE_BASE(0) +   3)
+#define PCM186X_PGA_VAL_CH2_R		(PCM186X_PAGE_BASE(0) +   4)
+#define PCM186X_PGA_CTRL		(PCM186X_PAGE_BASE(0) +   5)
+#define PCM186X_ADC1_INPUT_SEL_L	(PCM186X_PAGE_BASE(0) +   6)
+#define PCM186X_ADC1_INPUT_SEL_R	(PCM186X_PAGE_BASE(0) +   7)
+#define PCM186X_ADC2_INPUT_SEL_L	(PCM186X_PAGE_BASE(0) +   8)
+#define PCM186X_ADC2_INPUT_SEL_R	(PCM186X_PAGE_BASE(0) +   9)
+#define PCM186X_AUXADC_INPUT_SEL	(PCM186X_PAGE_BASE(0) +  10)
+#define PCM186X_PCM_CFG			(PCM186X_PAGE_BASE(0) +  11)
+#define PCM186X_TDM_TX_SEL		(PCM186X_PAGE_BASE(0) +  12)
+#define PCM186X_TDM_TX_OFFSET		(PCM186X_PAGE_BASE(0) +  13)
+#define PCM186X_TDM_RX_OFFSET		(PCM186X_PAGE_BASE(0) +  14)
+#define PCM186X_DPGA_VAL_CH1_L		(PCM186X_PAGE_BASE(0) +  15)
+#define PCM186X_GPIO1_0_CTRL		(PCM186X_PAGE_BASE(0) +  16)
+#define PCM186X_GPIO3_2_CTRL		(PCM186X_PAGE_BASE(0) +  17)
+#define PCM186X_GPIO1_0_DIR_CTRL	(PCM186X_PAGE_BASE(0) +  18)
+#define PCM186X_GPIO3_2_DIR_CTRL	(PCM186X_PAGE_BASE(0) +  19)
+#define PCM186X_GPIO_IN_OUT		(PCM186X_PAGE_BASE(0) +  20)
+#define PCM186X_GPIO_PULL_CTRL		(PCM186X_PAGE_BASE(0) +  21)
+#define PCM186X_DPGA_VAL_CH1_R		(PCM186X_PAGE_BASE(0) +  22)
+#define PCM186X_DPGA_VAL_CH2_L		(PCM186X_PAGE_BASE(0) +  23)
+#define PCM186X_DPGA_VAL_CH2_R		(PCM186X_PAGE_BASE(0) +  24)
+#define PCM186X_DPGA_GAIN_CTRL		(PCM186X_PAGE_BASE(0) +  25)
+#define PCM186X_DPGA_MIC_CTRL		(PCM186X_PAGE_BASE(0) +  26)
+#define PCM186X_DIN_RESAMP_CTRL		(PCM186X_PAGE_BASE(0) +  27)
+#define PCM186X_CLK_CTRL		(PCM186X_PAGE_BASE(0) +  32)
+#define PCM186X_DSP1_CLK_DIV		(PCM186X_PAGE_BASE(0) +  33)
+#define PCM186X_DSP2_CLK_DIV		(PCM186X_PAGE_BASE(0) +  34)
+#define PCM186X_ADC_CLK_DIV		(PCM186X_PAGE_BASE(0) +  35)
+#define PCM186X_PLL_SCK_DIV		(PCM186X_PAGE_BASE(0) +  37)
+#define PCM186X_BCK_DIV			(PCM186X_PAGE_BASE(0) +  38)
+#define PCM186X_LRK_DIV			(PCM186X_PAGE_BASE(0) +  39)
+#define PCM186X_PLL_CTRL		(PCM186X_PAGE_BASE(0) +  40)
+#define PCM186X_PLL_P_DIV		(PCM186X_PAGE_BASE(0) +  41)
+#define PCM186X_PLL_R_DIV		(PCM186X_PAGE_BASE(0) +  42)
+#define PCM186X_PLL_J_DIV		(PCM186X_PAGE_BASE(0) +  43)
+#define PCM186X_PLL_D_DIV_LSB		(PCM186X_PAGE_BASE(0) +  44)
+#define PCM186X_PLL_D_DIV_MSB		(PCM186X_PAGE_BASE(0) +  45)
+#define PCM186X_SIGDET_MODE		(PCM186X_PAGE_BASE(0) +  48)
+#define PCM186X_SIGDET_MASK		(PCM186X_PAGE_BASE(0) +  49)
+#define PCM186X_SIGDET_STAT		(PCM186X_PAGE_BASE(0) +  50)
+#define PCM186X_SIGDET_LOSS_TIME	(PCM186X_PAGE_BASE(0) +  52)
+#define PCM186X_SIGDET_SCAN_TIME	(PCM186X_PAGE_BASE(0) +  53)
+#define PCM186X_SIGDET_INT_INTVL	(PCM186X_PAGE_BASE(0) +  54)
+#define PCM186X_SIGDET_DC_REF_CH1_L	(PCM186X_PAGE_BASE(0) +  64)
+#define PCM186X_SIGDET_DC_DIFF_CH1_L	(PCM186X_PAGE_BASE(0) +  65)
+#define PCM186X_SIGDET_DC_LEV_CH1_L	(PCM186X_PAGE_BASE(0) +  66)
+#define PCM186X_SIGDET_DC_REF_CH1_R	(PCM186X_PAGE_BASE(0) +  67)
+#define PCM186X_SIGDET_DC_DIFF_CH1_R	(PCM186X_PAGE_BASE(0) +  68)
+#define PCM186X_SIGDET_DC_LEV_CH1_R	(PCM186X_PAGE_BASE(0) +  69)
+#define PCM186X_SIGDET_DC_REF_CH2_L	(PCM186X_PAGE_BASE(0) +  70)
+#define PCM186X_SIGDET_DC_DIFF_CH2_L	(PCM186X_PAGE_BASE(0) +  71)
+#define PCM186X_SIGDET_DC_LEV_CH2_L	(PCM186X_PAGE_BASE(0) +  72)
+#define PCM186X_SIGDET_DC_REF_CH2_R	(PCM186X_PAGE_BASE(0) +  73)
+#define PCM186X_SIGDET_DC_DIFF_CH2_R	(PCM186X_PAGE_BASE(0) +  74)
+#define PCM186X_SIGDET_DC_LEV_CH2_R	(PCM186X_PAGE_BASE(0) +  75)
+#define PCM186X_SIGDET_DC_REF_CH3_L	(PCM186X_PAGE_BASE(0) +  76)
+#define PCM186X_SIGDET_DC_DIFF_CH3_L	(PCM186X_PAGE_BASE(0) +  77)
+#define PCM186X_SIGDET_DC_LEV_CH3_L	(PCM186X_PAGE_BASE(0) +  78)
+#define PCM186X_SIGDET_DC_REF_CH3_R	(PCM186X_PAGE_BASE(0) +  79)
+#define PCM186X_SIGDET_DC_DIFF_CH3_R	(PCM186X_PAGE_BASE(0) +  80)
+#define PCM186X_SIGDET_DC_LEV_CH3_R	(PCM186X_PAGE_BASE(0) +  81)
+#define PCM186X_SIGDET_DC_REF_CH4_L	(PCM186X_PAGE_BASE(0) +  82)
+#define PCM186X_SIGDET_DC_DIFF_CH4_L	(PCM186X_PAGE_BASE(0) +  83)
+#define PCM186X_SIGDET_DC_LEV_CH4_L	(PCM186X_PAGE_BASE(0) +  84)
+#define PCM186X_SIGDET_DC_REF_CH4_R	(PCM186X_PAGE_BASE(0) +  85)
+#define PCM186X_SIGDET_DC_DIFF_CH4_R	(PCM186X_PAGE_BASE(0) +  86)
+#define PCM186X_SIGDET_DC_LEV_CH4_R	(PCM186X_PAGE_BASE(0) +  87)
+#define PCM186X_AUXADC_DATA_CTRL	(PCM186X_PAGE_BASE(0) +  88)
+#define PCM186X_AUXADC_DATA_LSB		(PCM186X_PAGE_BASE(0) +  89)
+#define PCM186X_AUXADC_DATA_MSB		(PCM186X_PAGE_BASE(0) +  90)
+#define PCM186X_INT_ENABLE		(PCM186X_PAGE_BASE(0) +  96)
+#define PCM186X_INT_FLAG		(PCM186X_PAGE_BASE(0) +  97)
+#define PCM186X_INT_POL_WIDTH		(PCM186X_PAGE_BASE(0) +  98)
+#define PCM186X_POWER_CTRL		(PCM186X_PAGE_BASE(0) + 112)
+#define PCM186X_FILTER_MUTE_CTRL	(PCM186X_PAGE_BASE(0) + 113)
+#define PCM186X_DEVICE_STATUS		(PCM186X_PAGE_BASE(0) + 114)
+#define PCM186X_FSAMPLE_STATUS		(PCM186X_PAGE_BASE(0) + 115)
+#define PCM186X_DIV_STATUS		(PCM186X_PAGE_BASE(0) + 116)
+#define PCM186X_CLK_STATUS		(PCM186X_PAGE_BASE(0) + 117)
+#define PCM186X_SUPPLY_STATUS		(PCM186X_PAGE_BASE(0) + 120)
+
+/* Register Definitions - Page 1 */
+#define PCM186X_MMAP_STAT_CTRL		(PCM186X_PAGE_BASE(1) +   1)
+#define PCM186X_MMAP_ADDRESS		(PCM186X_PAGE_BASE(1) +   2)
+#define PCM186X_MEM_WDATA0		(PCM186X_PAGE_BASE(1) +   4)
+#define PCM186X_MEM_WDATA1		(PCM186X_PAGE_BASE(1) +   5)
+#define PCM186X_MEM_WDATA2		(PCM186X_PAGE_BASE(1) +   6)
+#define PCM186X_MEM_WDATA3		(PCM186X_PAGE_BASE(1) +   7)
+#define PCM186X_MEM_RDATA0		(PCM186X_PAGE_BASE(1) +   8)
+#define PCM186X_MEM_RDATA1		(PCM186X_PAGE_BASE(1) +   9)
+#define PCM186X_MEM_RDATA2		(PCM186X_PAGE_BASE(1) +  10)
+#define PCM186X_MEM_RDATA3		(PCM186X_PAGE_BASE(1) +  11)
+
+/* Register Definitions - Page 3 */
+#define PCM186X_OSC_PWR_DOWN_CTRL	(PCM186X_PAGE_BASE(3) +  18)
+#define PCM186X_MIC_BIAS_CTRL		(PCM186X_PAGE_BASE(3) +  21)
+
+/* Register Definitions - Page 253 */
+#define PCM186X_CURR_TRIM_CTRL		(PCM186X_PAGE_BASE(253) +  20)
+
+#define PCM186X_MAX_REGISTER		PCM186X_CURR_TRIM_CTRL
+
+/* PCM186X_PAGE */
+#define PCM186X_RESET			0xff
+
+/* PCM186X_ADCX_INPUT_SEL_X */
+#define PCM186X_ADC_INPUT_SEL_POL	BIT(7)
+#define PCM186X_ADC_INPUT_SEL_MASK	GENMASK(5, 0)
+
+/* PCM186X_PCM_CFG */
+#define PCM186X_PCM_CFG_RX_WLEN_MASK	GENMASK(7, 6)
+#define PCM186X_PCM_CFG_RX_WLEN_SHIFT	6
+#define PCM186X_PCM_CFG_RX_WLEN_32	0x00
+#define PCM186X_PCM_CFG_RX_WLEN_24	0x01
+#define PCM186X_PCM_CFG_RX_WLEN_20	0x02
+#define PCM186X_PCM_CFG_RX_WLEN_16	0x03
+#define PCM186X_PCM_CFG_TDM_LRCK_MODE	BIT(4)
+#define PCM186X_PCM_CFG_TX_WLEN_MASK	GENMASK(3, 2)
+#define PCM186X_PCM_CFG_TX_WLEN_SHIFT	2
+#define PCM186X_PCM_CFG_TX_WLEN_32	0x00
+#define PCM186X_PCM_CFG_TX_WLEN_24	0x01
+#define PCM186X_PCM_CFG_TX_WLEN_20	0x02
+#define PCM186X_PCM_CFG_TX_WLEN_16	0x03
+#define PCM186X_PCM_CFG_FMT_MASK	GENMASK(1, 0)
+#define PCM186X_PCM_CFG_FMT_SHIFT	0
+#define PCM186X_PCM_CFG_FMT_I2S		0x00
+#define PCM186X_PCM_CFG_FMT_LEFTJ	0x01
+#define PCM186X_PCM_CFG_FMT_RIGHTJ	0x02
+#define PCM186X_PCM_CFG_FMT_TDM		0x03
+
+/* PCM186X_TDM_TX_SEL */
+#define PCM186X_TDM_TX_SEL_2CH		0x00
+#define PCM186X_TDM_TX_SEL_4CH		0x01
+#define PCM186X_TDM_TX_SEL_6CH		0x02
+#define PCM186X_TDM_TX_SEL_MASK		0x03
+
+/* PCM186X_CLK_CTRL */
+#define PCM186X_CLK_CTRL_SCK_XI_SEL1	BIT(7)
+#define PCM186X_CLK_CTRL_SCK_XI_SEL0	BIT(6)
+#define PCM186X_CLK_CTRL_SCK_SRC_PLL	BIT(5)
+#define PCM186X_CLK_CTRL_MST_MODE	BIT(4)
+#define PCM186X_CLK_CTRL_ADC_SRC_PLL	BIT(3)
+#define PCM186X_CLK_CTRL_DSP2_SRC_PLL	BIT(2)
+#define PCM186X_CLK_CTRL_DSP1_SRC_PLL	BIT(1)
+#define PCM186X_CLK_CTRL_CLKDET_EN	BIT(0)
+
+/* PCM186X_PLL_CTRL */
+#define PCM186X_PLL_CTRL_LOCK		BIT(4)
+#define PCM186X_PLL_CTRL_REF_SEL	BIT(1)
+#define PCM186X_PLL_CTRL_EN		BIT(0)
+
+/* PCM186X_POWER_CTRL */
+#define PCM186X_PWR_CTRL_PWRDN		BIT(2)
+#define PCM186X_PWR_CTRL_SLEEP		BIT(1)
+#define PCM186X_PWR_CTRL_STBY		BIT(0)
+
+/* PCM186X_CLK_STATUS */
+#define PCM186X_CLK_STATUS_LRCKHLT	BIT(6)
+#define PCM186X_CLK_STATUS_BCKHLT	BIT(5)
+#define PCM186X_CLK_STATUS_SCKHLT	BIT(4)
+#define PCM186X_CLK_STATUS_LRCKERR	BIT(2)
+#define PCM186X_CLK_STATUS_BCKERR	BIT(1)
+#define PCM186X_CLK_STATUS_SCKERR	BIT(0)
+
+/* PCM186X_SUPPLY_STATUS */
+#define PCM186X_SUPPLY_STATUS_DVDD	BIT(2)
+#define PCM186X_SUPPLY_STATUS_AVDD	BIT(1)
+#define PCM186X_SUPPLY_STATUS_LDO	BIT(0)
+
+/* PCM186X_MMAP_STAT_CTRL */
+#define PCM186X_MMAP_STAT_DONE		BIT(4)
+#define PCM186X_MMAP_STAT_BUSY		BIT(2)
+#define PCM186X_MMAP_STAT_R_REQ		BIT(1)
+#define PCM186X_MMAP_STAT_W_REQ		BIT(0)
+
+extern const struct dev_pm_ops pcm186x_pm_ops;
+extern const struct regmap_config pcm186x_regmap;
+
+int pcm186x_probe(struct device *dev, enum pcm186x_type type, int irq,
+		  struct regmap *regmap);
+int pcm186x_remove(struct device *dev);
+
+#endif /* _PCM186X_H_ */
-- 
2.15.0

Re: [PATCH v2 2/2] ASoC: codecs: Add initial PCM1862/63/64/65 universal ADC driver

[Mark Brown]

[-- Attachment #1: Type: text/plain, Size: 1915 bytes --]

On Wed, Nov 29, 2017 at 12:50:15PM -0600, Andrew F. Davis wrote:

> +	case SND_SOC_BIAS_STANDBY:
> +		pcm186x_power_on(codec);
> +		break;
> +	case SND_SOC_BIAS_OFF:
> +		pcm186x_power_off(codec);
> +		break;
> +	}

> +/*
> + * The PCM186x's page register is located on every page, allowing to program it
> + * without having to switch pages. Take advantage of this by defining the range
> + * such to have this register located inside the data window.
> + */

That sounds like a normal page register?

> +int pcm186x_probe(struct device *dev, enum pcm186x_type type, int irq,
> +		  struct regmap *regmap)
> +{

> +	ret = regulator_bulk_disable(ARRAY_SIZE(priv->supplies),
> +				     priv->supplies);
> +	if (ret) {
> +		dev_err(dev, "failed disable supplies: %d\n", ret);
> +		return ret;
> +	}

> +static int __maybe_unused pcm186x_resume(struct device *dev)
> +{
> +	struct pcm186x_priv *priv = dev_get_drvdata(dev);
> +	int ret;
> +
> +	ret = regulator_bulk_enable(ARRAY_SIZE(priv->supplies),
> +				    priv->supplies);
> +	if (ret != 0) {
> +		dev_err(dev, "failed to enable supplies: %d\n", ret);
> +		return ret;
> +	}

> +const struct dev_pm_ops pcm186x_pm_ops = {
> +	SET_RUNTIME_PM_OPS(pcm186x_suspend, pcm186x_resume, NULL)
> +};
> +EXPORT_SYMBOL_GPL(pcm186x_pm_ops);

There's no code in the driver that enables runtime PM so this isn't
going to do anything.  I'm also not clear that the power management
handling is in general joined up - we leave the regulators disabled
at the end of probe, relying on the bias level configuration to reenable
them but then the runtime PM configuration also tries to enable and
disable them.  Based on what I think the intention is I'd suggest
removing the bias level handling and then having probe enable runtime
PM with the device flagged as active, letting runtime PM do any
disabling if the device is idle.

I'd also expect to see some system suspend handling.

[-- Attachment #2: signature.asc --]
[-- Type: application/pgp-signature, Size: 488 bytes --]

Re: [PATCH v2 2/2] ASoC: codecs: Add initial PCM1862/63/64/65 universal ADC driver

[Andrew F. Davis]

On 11/30/2017 06:20 AM, Mark Brown wrote:
> On Wed, Nov 29, 2017 at 12:50:15PM -0600, Andrew F. Davis wrote:
> 
>> +	case SND_SOC_BIAS_STANDBY:
>> +		pcm186x_power_on(codec);
>> +		break;
>> +	case SND_SOC_BIAS_OFF:
>> +		pcm186x_power_off(codec);
>> +		break;
>> +	}
> 
>> +/*
>> + * The PCM186x's page register is located on every page, allowing to program it
>> + * without having to switch pages. Take advantage of this by defining the range
>> + * such to have this register located inside the data window.
>> + */
> 
> That sounds like a normal page register?
> 

It is, I believe Andreas commented this for his own reference, I'll drop it.

>> +int pcm186x_probe(struct device *dev, enum pcm186x_type type, int irq,
>> +		  struct regmap *regmap)
>> +{
> 
>> +	ret = regulator_bulk_disable(ARRAY_SIZE(priv->supplies),
>> +				     priv->supplies);
>> +	if (ret) {
>> +		dev_err(dev, "failed disable supplies: %d\n", ret);
>> +		return ret;
>> +	}
> 
>> +static int __maybe_unused pcm186x_resume(struct device *dev)
>> +{
>> +	struct pcm186x_priv *priv = dev_get_drvdata(dev);
>> +	int ret;
>> +
>> +	ret = regulator_bulk_enable(ARRAY_SIZE(priv->supplies),
>> +				    priv->supplies);
>> +	if (ret != 0) {
>> +		dev_err(dev, "failed to enable supplies: %d\n", ret);
>> +		return ret;
>> +	}
> 
>> +const struct dev_pm_ops pcm186x_pm_ops = {
>> +	SET_RUNTIME_PM_OPS(pcm186x_suspend, pcm186x_resume, NULL)
>> +};
>> +EXPORT_SYMBOL_GPL(pcm186x_pm_ops);
> 
> There's no code in the driver that enables runtime PM so this isn't
> going to do anything.  I'm also not clear that the power management
> handling is in general joined up - we leave the regulators disabled
> at the end of probe, relying on the bias level configuration to reenable
> them but then the runtime PM configuration also tries to enable and
> disable them.  Based on what I think the intention is I'd suggest
> removing the bias level handling and then having probe enable runtime
> PM with the device flagged as active, letting runtime PM do any
> disabling if the device is idle.
> 

I beleive this was meant to be be SIMPLE_DEV_PM_OPS and not
SET_RUNTIME_PM_OPS. I'll fix this all up for v3.

Just thinking, the sound core sets SND_SOC_BIAS_OFF before suspend
anyway, right? So the results would be similar just having all the PM
stuff in the bias level handling for consistency, but I'm open to
whatever is the preferred way.

> I'd also expect to see some system suspend handling.
> 
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at  http://vger.kernel.org/majordomo-info.html

Re: [PATCH v2 2/2] ASoC: codecs: Add initial PCM1862/63/64/65 universal ADC driver

[Mark Brown]

[-- Attachment #1.1: Type: text/plain, Size: 1098 bytes --]

On Thu, Nov 30, 2017 at 09:56:08AM -0600, Andrew F. Davis wrote:
> On 11/30/2017 06:20 AM, Mark Brown wrote:

> > disable them.  Based on what I think the intention is I'd suggest
> > removing the bias level handling and then having probe enable runtime
> > PM with the device flagged as active, letting runtime PM do any
> > disabling if the device is idle.

> I beleive this was meant to be be SIMPLE_DEV_PM_OPS and not
> SET_RUNTIME_PM_OPS. I'll fix this all up for v3.

I was wondering that.

> Just thinking, the sound core sets SND_SOC_BIAS_OFF before suspend
> anyway, right? So the results would be similar just having all the PM
> stuff in the bias level handling for consistency, but I'm open to
> whatever is the preferred way.

It doesn't matter that much, if you do it only in set_bias_level() then
unless you set idle_bias_off there will be no runtime PM which may or
may not be what you want and you'll also not give the user the ability
to control if runtime PM happens via the sysfs files but I'm not
convinced that anyone ever actually does that.  Either approach is fine
really.

[-- Attachment #1.2: signature.asc --]
[-- Type: application/pgp-signature, Size: 488 bytes --]

[-- Attachment #2: Type: text/plain, Size: 0 bytes --]

Applied "ASoC: pcm186x: Add PCM186x binding documentation" to the asoc tree

[Mark Brown]

The patch

   ASoC: pcm186x: Add PCM186x binding documentation

has been applied to the asoc tree at

   https://git.kernel.org/pub/scm/linux/kernel/git/broonie/sound.git 

All being well this means that it will be integrated into the linux-next
tree (usually sometime in the next 24 hours) and sent to Linus during
the next merge window (or sooner if it is a bug fix), however if
problems are discovered then the patch may be dropped or reverted.  

You may get further e-mails resulting from automated or manual testing
and review of the tree, please engage with people reporting problems and
send followup patches addressing any issues that are reported if needed.

If any updates are required or you are submitting further changes they
should be sent as incremental updates against current git, existing
patches will not be replaced.

Please add any relevant lists and maintainers to the CCs when replying
to this mail.

Thanks,
Mark

>From eb2a8168b9fd69f66199d9d7e86d23fecfab4e33 Mon Sep 17 00:00:00 2001
From: "Andrew F. Davis" <afd@ti.com>
Date: Tue, 5 Dec 2017 14:52:55 -0600
Subject: [PATCH] ASoC: pcm186x: Add PCM186x binding documentation

Add the dt-binding documentation for the TI PCM186x 2ch and 4ch Audio
ADCs With Universal Front End.

Signed-off-by: Andrew F. Davis <afd@ti.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
---
 .../devicetree/bindings/sound/pcm186x.txt          | 42 ++++++++++++++++++++++
 1 file changed, 42 insertions(+)
 create mode 100644 Documentation/devicetree/bindings/sound/pcm186x.txt

diff --git a/Documentation/devicetree/bindings/sound/pcm186x.txt b/Documentation/devicetree/bindings/sound/pcm186x.txt
new file mode 100644
index 000000000000..1087f4855980
--- /dev/null
+++ b/Documentation/devicetree/bindings/sound/pcm186x.txt
@@ -0,0 +1,42 @@
+Texas Instruments PCM186x Universal Audio ADC
+
+These devices support both I2C and SPI (configured with pin strapping
+on the board).
+
+Required properties:
+
+ - compatible : "ti,pcm1862",
+                "ti,pcm1863",
+                "ti,pcm1864",
+                "ti,pcm1865"
+
+ - reg : The I2C address of the device for I2C, the chip select
+         number for SPI.
+
+ - avdd-supply: Analog core power supply (3.3v)
+ - dvdd-supply: Digital core power supply
+ - iovdd-supply: Digital IO power supply
+        See regulator/regulator.txt for more information
+
+CODEC input pins:
+ * VINL1
+ * VINR1
+ * VINL2
+ * VINR2
+ * VINL3
+ * VINR3
+ * VINL4
+ * VINR4
+
+The pins can be used in referring sound node's audio-routing property.
+
+Example:
+
+	pcm186x: audio-codec@4a {
+		compatible = "ti,pcm1865";
+		reg = <0x4a>;
+
+		avdd-supply = <&reg_3v3_analog>;
+		dvdd-supply = <&reg_3v3>;
+		iovdd-supply = <&reg_1v8>;
+	};
-- 
2.15.0