[PATCH v3 0/6] arm: sunxi: IR support for A83T

[PATCH v3 0/6] arm: sunxi: IR support for A83T

[Philipp Rossak]

This patch series adds support for the sunxi A83T ir module and enhances 
the sunxi-ir driver. Right now the base clock frequency for the ir driver
is a hard coded define and is set to 8 MHz.
This works for the most common ir receivers. On the Sinovoip Bananapi M3 
the ir receiver needs, a 3 MHz base clock frequency to work without
problems with this driver.

This patch series adds support for an optinal property that makes it able
to override the default base clock frequency and enables the ir interface 
on the a83t and the Bananapi M3.

changes since v2:
* reorder cir pin (alphabetical)
* fix typo in documentation

changes since v1:
* fix typos, reword Documentation
* initialize 'b_clk_freq' to 'SUNXI_IR_BASE_CLK' & remove if statement
* change dev_info() to dev_dbg()
* change naming to cir* in dts/dtsi
* Added acked Ackedi-by to related patch
* use whole memory block instead of registers needed + fix for h3/h5

changes since rfc:
* The property is now optinal. If the property is not available in 
  the dtb the driver uses the default base clock frequency.
* the driver prints out the the selected base clock frequency.
* changed devicetree property from base-clk-frequency to clock-frequency

Regards,
Philipp


Philipp Rossak (6):
  media: rc: update sunxi-ir driver to get base clock frequency from
    devicetree
  media: dt: bindings: Update binding documentation for sunxi IR
    controller
  arm: dts: sun8i: a83t: Add the cir pin for the A83T
  arm: dts: sun8i: a83t: Add support for the cir interface
  arm: dts: sun8i: a83t: bananapi-m3: Enable IR controller
  arm: dts: sun8i: h3-h8: ir register size should be the whole memory
    block

 Documentation/devicetree/bindings/media/sunxi-ir.txt |  3 +++
 arch/arm/boot/dts/sun8i-a83t-bananapi-m3.dts         |  7 +++++++
 arch/arm/boot/dts/sun8i-a83t.dtsi                    | 15 +++++++++++++++
 arch/arm/boot/dts/sunxi-h3-h5.dtsi                   |  2 +-
 drivers/media/rc/sunxi-cir.c                         | 19 +++++++++++--------
 5 files changed, 37 insertions(+), 9 deletions(-)

-- 
2.11.0

[PATCH v3 1/6] media: rc: update sunxi-ir driver to get base clock frequency from devicetree

[Philipp Rossak]

This patch updates the sunxi-ir driver to set the base clock frequency from
devicetree.

This is necessary since there are different ir receivers on the
market, that operate with different frequencies. So this value could be
set if the attached ir receiver needs a different base clock frequency,
than the default 8 MHz.

Signed-off-by: Philipp Rossak <embed3d-Re5JQEeQqe8AvxtiuMwx3w@public.gmane.org>
---
 drivers/media/rc/sunxi-cir.c | 19 +++++++++++--------
 1 file changed, 11 insertions(+), 8 deletions(-)

diff --git a/drivers/media/rc/sunxi-cir.c b/drivers/media/rc/sunxi-cir.c
index 97f367b446c4..f500cea228a9 100644
--- a/drivers/media/rc/sunxi-cir.c
+++ b/drivers/media/rc/sunxi-cir.c
@@ -72,12 +72,8 @@
 /* CIR_REG register idle threshold */
 #define REG_CIR_ITHR(val)    (((val) << 8) & (GENMASK(15, 8)))
 
-/* Required frequency for IR0 or IR1 clock in CIR mode */
+/* Required frequency for IR0 or IR1 clock in CIR mode (default) */
 #define SUNXI_IR_BASE_CLK     8000000
-/* Frequency after IR internal divider  */
-#define SUNXI_IR_CLK          (SUNXI_IR_BASE_CLK / 64)
-/* Sample period in ns */
-#define SUNXI_IR_SAMPLE       (1000000000ul / SUNXI_IR_CLK)
 /* Noise threshold in samples  */
 #define SUNXI_IR_RXNOISE      1
 /* Idle Threshold in samples */
@@ -122,7 +118,8 @@ static irqreturn_t sunxi_ir_irq(int irqno, void *dev_id)
 			/* for each bit in fifo */
 			dt = readb(ir->base + SUNXI_IR_RXFIFO_REG);
 			rawir.pulse = (dt & 0x80) != 0;
-			rawir.duration = ((dt & 0x7f) + 1) * SUNXI_IR_SAMPLE;
+			rawir.duration = ((dt & 0x7f) + 1) *
+					 ir->rc->rx_resolution;
 			ir_raw_event_store_with_filter(ir->rc, &rawir);
 		}
 	}
@@ -148,6 +145,7 @@ static int sunxi_ir_probe(struct platform_device *pdev)
 	struct device_node *dn = dev->of_node;
 	struct resource *res;
 	struct sunxi_ir *ir;
+	u32 b_clk_freq = SUNXI_IR_BASE_CLK;
 
 	ir = devm_kzalloc(dev, sizeof(struct sunxi_ir), GFP_KERNEL);
 	if (!ir)
@@ -172,6 +170,9 @@ static int sunxi_ir_probe(struct platform_device *pdev)
 		return PTR_ERR(ir->clk);
 	}
 
+	/* Base clock frequency (optional) */
+	of_property_read_u32(dn, "clock-frequency", &b_clk_freq);
+
 	/* Reset (optional) */
 	ir->rst = devm_reset_control_get_optional_exclusive(dev, NULL);
 	if (IS_ERR(ir->rst))
@@ -180,11 +181,12 @@ static int sunxi_ir_probe(struct platform_device *pdev)
 	if (ret)
 		return ret;
 
-	ret = clk_set_rate(ir->clk, SUNXI_IR_BASE_CLK);
+	ret = clk_set_rate(ir->clk, b_clk_freq);
 	if (ret) {
 		dev_err(dev, "set ir base clock failed!\n");
 		goto exit_reset_assert;
 	}
+	dev_dbg(dev, "set base clock frequency to %d Hz.\n", b_clk_freq);
 
 	if (clk_prepare_enable(ir->apb_clk)) {
 		dev_err(dev, "try to enable apb_ir_clk failed\n");
@@ -225,7 +227,8 @@ static int sunxi_ir_probe(struct platform_device *pdev)
 	ir->rc->map_name = ir->map_name ?: RC_MAP_EMPTY;
 	ir->rc->dev.parent = dev;
 	ir->rc->allowed_protocols = RC_PROTO_BIT_ALL_IR_DECODER;
-	ir->rc->rx_resolution = SUNXI_IR_SAMPLE;
+	/* Frequency after IR internal divider with sample period in ns */
+	ir->rc->rx_resolution = (1000000000ul / (b_clk_freq / 64));
 	ir->rc->timeout = MS_TO_NS(SUNXI_IR_TIMEOUT);
 	ir->rc->driver_name = SUNXI_IR_DEV;
 
-- 
2.11.0

[PATCH v3 2/6] media: dt: bindings: Update binding documentation for sunxi IR controller

[Philipp Rossak]

This patch updates documentation for Device-Tree bindings for sunxi IR
controller and adds the new optional property for the base clock
frequency.

Signed-off-by: Philipp Rossak <embed3d-Re5JQEeQqe8AvxtiuMwx3w@public.gmane.org>
---
 Documentation/devicetree/bindings/media/sunxi-ir.txt | 3 +++
 1 file changed, 3 insertions(+)

diff --git a/Documentation/devicetree/bindings/media/sunxi-ir.txt b/Documentation/devicetree/bindings/media/sunxi-ir.txt
index 91648c569b1e..278098987edb 100644
--- a/Documentation/devicetree/bindings/media/sunxi-ir.txt
+++ b/Documentation/devicetree/bindings/media/sunxi-ir.txt
@@ -11,6 +11,8 @@ Required properties:
 Optional properties:
 - linux,rc-map-name: see rc.txt file in the same directory.
 - resets : phandle + reset specifier pair
+- clock-frequency  : IR Receiver clock frequency, in Hertz. Defaults to 8 MHz
+		     if missing.
 
 Example:
 
@@ -18,6 +20,7 @@ ir0: ir@1c21800 {
 	compatible = "allwinner,sun4i-a10-ir";
 	clocks = <&apb0_gates 6>, <&ir0_clk>;
 	clock-names = "apb", "ir";
+	clock-frequency = <3000000>;
 	resets = <&apb0_rst 1>;
 	interrupts = <0 5 1>;
 	reg = <0x01C21800 0x40>;
-- 
2.11.0

[PATCH v3 3/6] arm: dts: sun8i: a83t: Add the cir pin for the A83T

[Philipp Rossak]

The CIR Pin of the A83T is located at PL12.

Signed-off-by: Philipp Rossak <embed3d-Re5JQEeQqe8AvxtiuMwx3w@public.gmane.org>
---
 arch/arm/boot/dts/sun8i-a83t.dtsi | 5 +++++
 1 file changed, 5 insertions(+)

diff --git a/arch/arm/boot/dts/sun8i-a83t.dtsi b/arch/arm/boot/dts/sun8i-a83t.dtsi
index de5119a2a91c..06e96db7c41a 100644
--- a/arch/arm/boot/dts/sun8i-a83t.dtsi
+++ b/arch/arm/boot/dts/sun8i-a83t.dtsi
@@ -617,6 +617,11 @@
 			interrupt-controller;
 			#interrupt-cells = <3>;
 
+			cir_pins: cir-pins@0 {
+				pins = "PL12";
+				function = "s_cir_rx";
+			};
+
 			r_rsb_pins: r-rsb-pins {
 				pins = "PL0", "PL1";
 				function = "s_rsb";
-- 
2.11.0

[PATCH v3 4/6] arm: dts: sun8i: a83t: Add support for the cir interface

[Philipp Rossak]

The cir interface is like on the H3 located at 0x01f02000 and is exactly
the same. This patch adds support for the ir interface on the A83T.

Signed-off-by: Philipp Rossak <embed3d-Re5JQEeQqe8AvxtiuMwx3w@public.gmane.org>
---
 arch/arm/boot/dts/sun8i-a83t.dtsi | 10 ++++++++++
 1 file changed, 10 insertions(+)

diff --git a/arch/arm/boot/dts/sun8i-a83t.dtsi b/arch/arm/boot/dts/sun8i-a83t.dtsi
index 06e96db7c41a..ddc0d592107f 100644
--- a/arch/arm/boot/dts/sun8i-a83t.dtsi
+++ b/arch/arm/boot/dts/sun8i-a83t.dtsi
@@ -605,6 +605,16 @@
 			#reset-cells = <1>;
 		};
 
+		cir: cir@01f02000 {
+			compatible = "allwinner,sun5i-a13-ir";
+			clocks = <&r_ccu CLK_APB0_IR>, <&r_ccu CLK_IR>;
+			clock-names = "apb", "ir";
+			resets = <&r_ccu RST_APB0_IR>;
+			interrupts = <GIC_SPI 37 IRQ_TYPE_LEVEL_HIGH>;
+			reg = <0x01f02000 0x400>;
+			status = "disabled";
+		};
+
 		r_pio: pinctrl@1f02c00 {
 			compatible = "allwinner,sun8i-a83t-r-pinctrl";
 			reg = <0x01f02c00 0x400>;
-- 
2.11.0

[PATCH v3 5/6] arm: dts: sun8i: a83t: bananapi-m3: Enable IR controller

[Philipp Rossak]

The Bananapi M3 has an onboard IR receiver.
This enables the onboard IR receiver subnode.
Unlike the other IR receivers this one needs a base clock frequency
of 3000000 Hz (3 MHz), to be able to work.

Signed-off-by: Philipp Rossak <embed3d-Re5JQEeQqe8AvxtiuMwx3w@public.gmane.org>
Acked-by: Chen-Yu Tsai <wens-jdAy2FN1RRM@public.gmane.org>
---
 arch/arm/boot/dts/sun8i-a83t-bananapi-m3.dts | 7 +++++++
 1 file changed, 7 insertions(+)

diff --git a/arch/arm/boot/dts/sun8i-a83t-bananapi-m3.dts b/arch/arm/boot/dts/sun8i-a83t-bananapi-m3.dts
index 6550bf0e594b..ffc6445fd281 100644
--- a/arch/arm/boot/dts/sun8i-a83t-bananapi-m3.dts
+++ b/arch/arm/boot/dts/sun8i-a83t-bananapi-m3.dts
@@ -82,6 +82,13 @@
 	};
 };
 
+&cir {
+	pinctrl-names = "default";
+	pinctrl-0 = <&cir_pins>;
+	clock-frequency = <3000000>;
+	status = "okay";
+};
+
 &ehci0 {
 	/* Terminus Tech FE 1.1s 4-port USB 2.0 hub here */
 	status = "okay";
-- 
2.11.0

[PATCH v3 6/6] arm: dts: sun8i: h3-h8: ir register size should be the whole memory block

[Philipp Rossak]

The size of the register should be the size of the whole memory block,
not just the registers, that are needed.

Signed-off-by: Philipp Rossak <embed3d-Re5JQEeQqe8AvxtiuMwx3w@public.gmane.org>
---
 arch/arm/boot/dts/sunxi-h3-h5.dtsi | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)

diff --git a/arch/arm/boot/dts/sunxi-h3-h5.dtsi b/arch/arm/boot/dts/sunxi-h3-h5.dtsi
index 8d40c00d64bb..a9caeda4a574 100644
--- a/arch/arm/boot/dts/sunxi-h3-h5.dtsi
+++ b/arch/arm/boot/dts/sunxi-h3-h5.dtsi
@@ -674,7 +674,7 @@
 			clock-names = "apb", "ir";
 			resets = <&r_ccu RST_APB0_IR>;
 			interrupts = <GIC_SPI 37 IRQ_TYPE_LEVEL_HIGH>;
-			reg = <0x01f02000 0x40>;
+			reg = <0x01f02000 0x400>;
 			status = "disabled";
 		};
 
-- 
2.11.0

Re: [PATCH v3 2/6] media: dt: bindings: Update binding documentation for sunxi IR controller

[Maxime Ripard]

[-- Attachment #1: Type: text/plain, Size: 498 bytes --]

On Tue, Dec 19, 2017 at 09:07:43AM +0100, Philipp Rossak wrote:
> This patch updates documentation for Device-Tree bindings for sunxi IR
> controller and adds the new optional property for the base clock
> frequency.
> 
> Signed-off-by: Philipp Rossak <embed3d-Re5JQEeQqe8AvxtiuMwx3w@public.gmane.org>

Acked-by: Maxime Ripard <maxime.ripard-wi1+55ScJUtKEb57/3fJTNBPR1lH4CV8@public.gmane.org>
Maxime

-- 
Maxime Ripard, Free Electrons
Embedded Linux and Kernel engineering
http://free-electrons.com

Re: [PATCH v3 2/6] media: dt: bindings: Update binding documentation for sunxi IR controller

[Rob Herring]

On Tue, Dec 19, 2017 at 09:07:43AM +0100, Philipp Rossak wrote:
> This patch updates documentation for Device-Tree bindings for sunxi IR
> controller and adds the new optional property for the base clock
> frequency.
> 
> Signed-off-by: Philipp Rossak <embed3d-Re5JQEeQqe8AvxtiuMwx3w@public.gmane.org>
> ---
>  Documentation/devicetree/bindings/media/sunxi-ir.txt | 3 +++
>  1 file changed, 3 insertions(+)

Reviewed-by: Rob Herring <robh-DgEjT+Ai2ygdnm+yROfE0A@public.gmane.org>

Re: [PATCH v3 1/6] media: rc: update sunxi-ir driver to get base clock frequency from devicetree

[Andi Shyti]

Hi Philipp,

On Tue, Dec 19, 2017 at 09:07:42AM +0100, Philipp Rossak wrote:
> This patch updates the sunxi-ir driver to set the base clock frequency from
> devicetree.
> 
> This is necessary since there are different ir receivers on the
> market, that operate with different frequencies. So this value could be
> set if the attached ir receiver needs a different base clock frequency,
> than the default 8 MHz.
> 
> Signed-off-by: Philipp Rossak <embed3d-Re5JQEeQqe8AvxtiuMwx3w@public.gmane.org>

feel free to add

Reviewed-by: Andi Shyti <andi.shyti-Sze3O3UU22JBDgjK7y7TUQ@public.gmane.org>

Andi
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at  http://vger.kernel.org/majordomo-info.html

Re: [PATCH v3 0/6] arm: sunxi: IR support for A83T

[Sean Young]

On Tue, Dec 19, 2017 at 09:07:41AM +0100, Philipp Rossak wrote:
> This patch series adds support for the sunxi A83T ir module and enhances 
> the sunxi-ir driver. Right now the base clock frequency for the ir driver
> is a hard coded define and is set to 8 MHz.
> This works for the most common ir receivers. On the Sinovoip Bananapi M3 
> the ir receiver needs, a 3 MHz base clock frequency to work without
> problems with this driver.
> 
> This patch series adds support for an optinal property that makes it able
> to override the default base clock frequency and enables the ir interface 
> on the a83t and the Bananapi M3.
> 
> changes since v2:
> * reorder cir pin (alphabetical)
> * fix typo in documentation
> 
> changes since v1:
> * fix typos, reword Documentation
> * initialize 'b_clk_freq' to 'SUNXI_IR_BASE_CLK' & remove if statement
> * change dev_info() to dev_dbg()
> * change naming to cir* in dts/dtsi
> * Added acked Ackedi-by to related patch
> * use whole memory block instead of registers needed + fix for h3/h5
> 
> changes since rfc:
> * The property is now optinal. If the property is not available in 
>   the dtb the driver uses the default base clock frequency.
> * the driver prints out the the selected base clock frequency.
> * changed devicetree property from base-clk-frequency to clock-frequency
> 
> Regards,
> Philipp
> 
> 
> Philipp Rossak (6):
>   media: rc: update sunxi-ir driver to get base clock frequency from
>     devicetree
>   media: dt: bindings: Update binding documentation for sunxi IR
>     controller
>   arm: dts: sun8i: a83t: Add the cir pin for the A83T
>   arm: dts: sun8i: a83t: Add support for the cir interface
>   arm: dts: sun8i: a83t: bananapi-m3: Enable IR controller
>   arm: dts: sun8i: h3-h8: ir register size should be the whole memory
>     block

I can take this series (through rc-core, i.e. linux-media), but I need an
maintainer Acked-by: for the sun[x8]i dts changes (all four patches).

>  Documentation/devicetree/bindings/media/sunxi-ir.txt |  3 +++
>  arch/arm/boot/dts/sun8i-a83t-bananapi-m3.dts         |  7 +++++++
>  arch/arm/boot/dts/sun8i-a83t.dtsi                    | 15 +++++++++++++++
>  arch/arm/boot/dts/sunxi-h3-h5.dtsi                   |  2 +-
>  drivers/media/rc/sunxi-cir.c                         | 19 +++++++++++--------
>  5 files changed, 37 insertions(+), 9 deletions(-)


Thanks
Sean

Re: [PATCH v3 0/6] arm: sunxi: IR support for A83T

[Maxime Ripard]

[-- Attachment #1: Type: text/plain, Size: 2493 bytes --]

Hi,

On Fri, Jan 05, 2018 at 12:02:53PM +0000, Sean Young wrote:
> On Tue, Dec 19, 2017 at 09:07:41AM +0100, Philipp Rossak wrote:
> > This patch series adds support for the sunxi A83T ir module and enhances 
> > the sunxi-ir driver. Right now the base clock frequency for the ir driver
> > is a hard coded define and is set to 8 MHz.
> > This works for the most common ir receivers. On the Sinovoip Bananapi M3 
> > the ir receiver needs, a 3 MHz base clock frequency to work without
> > problems with this driver.
> > 
> > This patch series adds support for an optinal property that makes it able
> > to override the default base clock frequency and enables the ir interface 
> > on the a83t and the Bananapi M3.
> > 
> > changes since v2:
> > * reorder cir pin (alphabetical)
> > * fix typo in documentation
> > 
> > changes since v1:
> > * fix typos, reword Documentation
> > * initialize 'b_clk_freq' to 'SUNXI_IR_BASE_CLK' & remove if statement
> > * change dev_info() to dev_dbg()
> > * change naming to cir* in dts/dtsi
> > * Added acked Ackedi-by to related patch
> > * use whole memory block instead of registers needed + fix for h3/h5
> > 
> > changes since rfc:
> > * The property is now optinal. If the property is not available in 
> >   the dtb the driver uses the default base clock frequency.
> > * the driver prints out the the selected base clock frequency.
> > * changed devicetree property from base-clk-frequency to clock-frequency
> > 
> > Regards,
> > Philipp
> > 
> > 
> > Philipp Rossak (6):
> >   media: rc: update sunxi-ir driver to get base clock frequency from
> >     devicetree
> >   media: dt: bindings: Update binding documentation for sunxi IR
> >     controller
> >   arm: dts: sun8i: a83t: Add the cir pin for the A83T
> >   arm: dts: sun8i: a83t: Add support for the cir interface
> >   arm: dts: sun8i: a83t: bananapi-m3: Enable IR controller
> >   arm: dts: sun8i: h3-h8: ir register size should be the whole memory
> >     block
> 
> I can take this series (through rc-core, i.e. linux-media), but I need an
> maintainer Acked-by: for the sun[x8]i dts changes (all four patches).

We'll merge them through our tree. We usually have a rather big number
of patches around, so we'd be better off avoiding conflicts :)

Philipp, can you resubmit the DTs as soon as -rc1 is out?

Thanks!
Maxime

-- 
Maxime Ripard, Free Electrons
Embedded Linux and Kernel engineering
http://free-electrons.com

[-- Attachment #2: signature.asc --]
[-- Type: application/pgp-signature, Size: 833 bytes --]

Re: [PATCH v3 1/6] media: rc: update sunxi-ir driver to get base clock frequency from devicetree

[Sean Young]

On Tue, Dec 19, 2017 at 09:07:42AM +0100, Philipp Rossak wrote:
> This patch updates the sunxi-ir driver to set the base clock frequency from
> devicetree.
> 
> This is necessary since there are different ir receivers on the
> market, that operate with different frequencies. So this value could be
> set if the attached ir receiver needs a different base clock frequency,
> than the default 8 MHz.
> 
> Signed-off-by: Philipp Rossak <embed3d-Re5JQEeQqe8AvxtiuMwx3w@public.gmane.org>

Acked-by: Sean Young <sean-hENCXIMQXOg@public.gmane.org>


Sean

> ---
>  drivers/media/rc/sunxi-cir.c | 19 +++++++++++--------
>  1 file changed, 11 insertions(+), 8 deletions(-)
> 
> diff --git a/drivers/media/rc/sunxi-cir.c b/drivers/media/rc/sunxi-cir.c
> index 97f367b446c4..f500cea228a9 100644
> --- a/drivers/media/rc/sunxi-cir.c
> +++ b/drivers/media/rc/sunxi-cir.c
> @@ -72,12 +72,8 @@
>  /* CIR_REG register idle threshold */
>  #define REG_CIR_ITHR(val)    (((val) << 8) & (GENMASK(15, 8)))
>  
> -/* Required frequency for IR0 or IR1 clock in CIR mode */
> +/* Required frequency for IR0 or IR1 clock in CIR mode (default) */
>  #define SUNXI_IR_BASE_CLK     8000000
> -/* Frequency after IR internal divider  */
> -#define SUNXI_IR_CLK          (SUNXI_IR_BASE_CLK / 64)
> -/* Sample period in ns */
> -#define SUNXI_IR_SAMPLE       (1000000000ul / SUNXI_IR_CLK)
>  /* Noise threshold in samples  */
>  #define SUNXI_IR_RXNOISE      1
>  /* Idle Threshold in samples */
> @@ -122,7 +118,8 @@ static irqreturn_t sunxi_ir_irq(int irqno, void *dev_id)
>  			/* for each bit in fifo */
>  			dt = readb(ir->base + SUNXI_IR_RXFIFO_REG);
>  			rawir.pulse = (dt & 0x80) != 0;
> -			rawir.duration = ((dt & 0x7f) + 1) * SUNXI_IR_SAMPLE;
> +			rawir.duration = ((dt & 0x7f) + 1) *
> +					 ir->rc->rx_resolution;
>  			ir_raw_event_store_with_filter(ir->rc, &rawir);
>  		}
>  	}
> @@ -148,6 +145,7 @@ static int sunxi_ir_probe(struct platform_device *pdev)
>  	struct device_node *dn = dev->of_node;
>  	struct resource *res;
>  	struct sunxi_ir *ir;
> +	u32 b_clk_freq = SUNXI_IR_BASE_CLK;
>  
>  	ir = devm_kzalloc(dev, sizeof(struct sunxi_ir), GFP_KERNEL);
>  	if (!ir)
> @@ -172,6 +170,9 @@ static int sunxi_ir_probe(struct platform_device *pdev)
>  		return PTR_ERR(ir->clk);
>  	}
>  
> +	/* Base clock frequency (optional) */
> +	of_property_read_u32(dn, "clock-frequency", &b_clk_freq);
> +
>  	/* Reset (optional) */
>  	ir->rst = devm_reset_control_get_optional_exclusive(dev, NULL);
>  	if (IS_ERR(ir->rst))
> @@ -180,11 +181,12 @@ static int sunxi_ir_probe(struct platform_device *pdev)
>  	if (ret)
>  		return ret;
>  
> -	ret = clk_set_rate(ir->clk, SUNXI_IR_BASE_CLK);
> +	ret = clk_set_rate(ir->clk, b_clk_freq);
>  	if (ret) {
>  		dev_err(dev, "set ir base clock failed!\n");
>  		goto exit_reset_assert;
>  	}
> +	dev_dbg(dev, "set base clock frequency to %d Hz.\n", b_clk_freq);
>  
>  	if (clk_prepare_enable(ir->apb_clk)) {
>  		dev_err(dev, "try to enable apb_ir_clk failed\n");
> @@ -225,7 +227,8 @@ static int sunxi_ir_probe(struct platform_device *pdev)
>  	ir->rc->map_name = ir->map_name ?: RC_MAP_EMPTY;
>  	ir->rc->dev.parent = dev;
>  	ir->rc->allowed_protocols = RC_PROTO_BIT_ALL_IR_DECODER;
> -	ir->rc->rx_resolution = SUNXI_IR_SAMPLE;
> +	/* Frequency after IR internal divider with sample period in ns */
> +	ir->rc->rx_resolution = (1000000000ul / (b_clk_freq / 64));
>  	ir->rc->timeout = MS_TO_NS(SUNXI_IR_TIMEOUT);
>  	ir->rc->driver_name = SUNXI_IR_DEV;
>  
> -- 
> 2.11.0
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at  http://vger.kernel.org/majordomo-info.html

Re: [PATCH v3 0/6] arm: sunxi: IR support for A83T

[Philipp Rossak]

On 05.01.2018 15:59, Maxime Ripard wrote:
> Hi,
> 
> On Fri, Jan 05, 2018 at 12:02:53PM +0000, Sean Young wrote:
>> On Tue, Dec 19, 2017 at 09:07:41AM +0100, Philipp Rossak wrote:
>>> This patch series adds support for the sunxi A83T ir module and enhances
>>> the sunxi-ir driver. Right now the base clock frequency for the ir driver
>>> is a hard coded define and is set to 8 MHz.
>>> This works for the most common ir receivers. On the Sinovoip Bananapi M3
>>> the ir receiver needs, a 3 MHz base clock frequency to work without
>>> problems with this driver.
>>>
>>> This patch series adds support for an optinal property that makes it able
>>> to override the default base clock frequency and enables the ir interface
>>> on the a83t and the Bananapi M3.
>>>
>>> changes since v2:
>>> * reorder cir pin (alphabetical)
>>> * fix typo in documentation
>>>
>>> changes since v1:
>>> * fix typos, reword Documentation
>>> * initialize 'b_clk_freq' to 'SUNXI_IR_BASE_CLK' & remove if statement
>>> * change dev_info() to dev_dbg()
>>> * change naming to cir* in dts/dtsi
>>> * Added acked Ackedi-by to related patch
>>> * use whole memory block instead of registers needed + fix for h3/h5
>>>
>>> changes since rfc:
>>> * The property is now optinal. If the property is not available in
>>>    the dtb the driver uses the default base clock frequency.
>>> * the driver prints out the the selected base clock frequency.
>>> * changed devicetree property from base-clk-frequency to clock-frequency
>>>
>>> Regards,
>>> Philipp
>>>
>>>
>>> Philipp Rossak (6):
>>>    media: rc: update sunxi-ir driver to get base clock frequency from
>>>      devicetree
>>>    media: dt: bindings: Update binding documentation for sunxi IR
>>>      controller
>>>    arm: dts: sun8i: a83t: Add the cir pin for the A83T
>>>    arm: dts: sun8i: a83t: Add support for the cir interface
>>>    arm: dts: sun8i: a83t: bananapi-m3: Enable IR controller
>>>    arm: dts: sun8i: h3-h8: ir register size should be the whole memory
>>>      block
>>
>> I can take this series (through rc-core, i.e. linux-media), but I need an
>> maintainer Acked-by: for the sun[x8]i dts changes (all four patches).
> 
> We'll merge them through our tree. We usually have a rather big number
> of patches around, so we'd be better off avoiding conflicts :)
> 
> Philipp, can you resubmit the DTs as soon as -rc1 is out?
> 
> Thanks!
> Maxime
> 
Yes, I can do this!

Regards,
Philipp