* [PATCH v3 3/7] mtd: nand: add reworked Marvell NAND controller driver
[not found] ` <20180109103637.23798-1-miquel.raynal-wi1+55ScJUtKEb57/3fJTNBPR1lH4CV8@public.gmane.org>
2018-01-09 10:36 ` [PATCH v3 1/7] dt-bindings: mtd: document new nand-rb property Miquel Raynal
2018-01-09 10:36 ` [PATCH v3 2/7] dt-bindings: mtd: add Marvell NAND controller documentation Miquel Raynal
@ 2018-01-09 10:36 ` Miquel Raynal
2018-01-09 10:36 ` [PATCH v3 4/7] mtd: nand: use reworked NAND controller driver with Marvell EBU SoCs Miquel Raynal
` (5 subsequent siblings)
8 siblings, 0 replies; 19+ messages in thread
From: Miquel Raynal @ 2018-01-09 10:36 UTC (permalink / raw)
To: David Woodhouse, Brian Norris, Boris Brezillon, Marek Vasut,
Richard Weinberger, Cyrille Pitchen, Rob Herring, Mark Rutland,
Jason Cooper, Andrew Lunn, Gregory Clement,
Sebastian Hesselbarth, Russell King, Daniel Mack, Haojian Zhuang,
Robert Jarzmik, Eric Miao, Catalin Marinas
Cc: linux-mtd-IAPFreCvJWM7uuMidbF8XUB+6BGkLq7r,
devicetree-u79uwXL29TY76Z2rM5mHXA,
linux-arm-kernel-IAPFreCvJWM7uuMidbF8XUB+6BGkLq7r,
Thomas Petazzoni, Antoine Tenart, Nadav Haklai, Miquel Raynal,
Ofer Heifetz, Hanna Hawa, Neta Zur Hershkovits, Willy Tarreau,
Sean Nyekjaer
Add marvell_nand driver which aims at replacing the existing pxa3xx_nand
driver.
The new driver intends to be easier to understand and follows the brand
new NAND framework rules by implementing hooks for every pattern the
controller might support and referencing them inside a parser object
that will be given to the core at each ->exec_op() call.
Raw accessors are implemented, useful to test/debug memory/filesystem
corruptions. Userspace binaries contained in the mtd-utils package may
now be used and their output trusted.
Most of the DT nodes using the old driver kept non-optimal timings from
the bootloader (even if there was some mechanisms to derive them if the
chip was ONFI compliant). The new default is to implement
->setup_data_interface() and follow the core's decision regarding the
chip.
Thanks to the improved timings, implementation of ONFI mode 5 support
(with EDO managed by adding a delay on data sampling), merging the
commands together and optimizing writes in the command registers, the
new driver may achieve faster throughputs in both directions.
Measurements show an improvement of about +23% read throughput and +24%
write throughput. These measurements have been done with an
Armada-385-DB-AP (4kiB NAND pages forced in 4-bit strength BCH ECC
correction) using the userspace tool 'flash_speed' from the MTD test
suite.
Besides these important topics, the new driver addresses several
unsolved known issues in the old driver which:
- did not work with ECC soft neither with ECC none ;
- relied on naked read/write (which is unchanged) while the NFCv1
embedded in the pxa3xx platforms do not implement it, so several
NAND commands did not actually ever work without any notice (like
reading the ONFI PARAM_PAGE or SET/GET_FEATURES) ;
- wrote the OOB data correctly, but was not able to read it correctly
past the first OOB data chunk ;
- did not retrieve ECC bytes ;
- used device tree bindings that did not allow more than one NAND chip,
and did not allow to choose the correct chip select if not
incrementing from 0. Plus, the Ready/Busy line used had to be 0.
Old device tree bindings are still supported but deprecated. A more
hierarchical view has to be used to keep the controller and the NAND
chip structures clearly separated both inside the device tree and also
in the driver code.
Signed-off-by: Miquel Raynal <miquel.raynal-wi1+55ScJUtKEb57/3fJTNBPR1lH4CV8@public.gmane.org>
Tested-by: Sean Nyekjaer <sean.nyekjaer-rjjw5hvvQKZaa/9Udqfwiw@public.gmane.org>
Tested-by: Willy Tarreau <w@1wt.eu>
---
drivers/mtd/nand/Kconfig | 13 +
drivers/mtd/nand/Makefile | 1 +
drivers/mtd/nand/marvell_nand.c | 2897 +++++++++++++++++++++++++++++++++++++++
3 files changed, 2911 insertions(+)
create mode 100644 drivers/mtd/nand/marvell_nand.c
diff --git a/drivers/mtd/nand/Kconfig b/drivers/mtd/nand/Kconfig
index 859eb7790c46..e6b8c59f2c0d 100644
--- a/drivers/mtd/nand/Kconfig
+++ b/drivers/mtd/nand/Kconfig
@@ -315,6 +315,7 @@ config MTD_NAND_ATMEL
config MTD_NAND_PXA3xx
tristate "NAND support on PXA3xx and Armada 370/XP"
+ depends on !MTD_NAND_MARVELL
depends on PXA3xx || ARCH_MMP || PLAT_ORION || ARCH_MVEBU
help
@@ -323,6 +324,18 @@ config MTD_NAND_PXA3xx
platforms (XP, 370, 375, 38x, 39x) and 64-bit Armada
platforms (7K, 8K) (NFCv2).
+config MTD_NAND_MARVELL
+ tristate "NAND controller support on Marvell boards"
+ depends on PXA3xx || ARCH_MMP || PLAT_ORION || ARCH_MVEBU || \
+ COMPILE_TEST
+ depends on HAS_IOMEM
+ help
+ This enables the NAND flash controller driver for Marvell boards,
+ including:
+ - PXA3xx processors (NFCv1)
+ - 32-bit Armada platforms (XP, 37x, 38x, 39x) (NFCv2)
+ - 64-bit Aramda platforms (7k, 8k) (NFCv2)
+
config MTD_NAND_SLC_LPC32XX
tristate "NXP LPC32xx SLC Controller"
depends on ARCH_LPC32XX
diff --git a/drivers/mtd/nand/Makefile b/drivers/mtd/nand/Makefile
index 118a1349aad3..921634ba400c 100644
--- a/drivers/mtd/nand/Makefile
+++ b/drivers/mtd/nand/Makefile
@@ -32,6 +32,7 @@ obj-$(CONFIG_MTD_NAND_OMAP2) += omap2_nand.o
obj-$(CONFIG_MTD_NAND_OMAP_BCH_BUILD) += omap_elm.o
obj-$(CONFIG_MTD_NAND_CM_X270) += cmx270_nand.o
obj-$(CONFIG_MTD_NAND_PXA3xx) += pxa3xx_nand.o
+obj-$(CONFIG_MTD_NAND_MARVELL) += marvell_nand.o
obj-$(CONFIG_MTD_NAND_TMIO) += tmio_nand.o
obj-$(CONFIG_MTD_NAND_PLATFORM) += plat_nand.o
obj-$(CONFIG_MTD_NAND_PASEMI) += pasemi_nand.o
diff --git a/drivers/mtd/nand/marvell_nand.c b/drivers/mtd/nand/marvell_nand.c
new file mode 100644
index 000000000000..9d01120d97c5
--- /dev/null
+++ b/drivers/mtd/nand/marvell_nand.c
@@ -0,0 +1,2897 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Marvell NAND flash controller driver
+ *
+ * Copyright (C) 2017 Marvell
+ * Author: Miquel RAYNAL <miquel.raynal-wi1+55ScJUtKEb57/3fJTNBPR1lH4CV8@public.gmane.org>
+ *
+ */
+
+#include <linux/module.h>
+#include <linux/clk.h>
+#include <linux/mtd/rawnand.h>
+#include <linux/of_platform.h>
+#include <linux/iopoll.h>
+#include <linux/interrupt.h>
+#include <linux/slab.h>
+#include <linux/mfd/syscon.h>
+#include <linux/regmap.h>
+#include <asm/unaligned.h>
+
+#include <linux/dmaengine.h>
+#include <linux/dma-mapping.h>
+#include <linux/dma/pxa-dma.h>
+#include <linux/platform_data/mtd-nand-pxa3xx.h>
+
+/* Data FIFO granularity, FIFO reads/writes must be a multiple of this length */
+#define FIFO_DEPTH 8
+#define FIFO_REP(x) (x / sizeof(u32))
+#define BCH_SEQ_READS (32 / FIFO_DEPTH)
+/* NFC does not support transfers of larger chunks at a time */
+#define MAX_CHUNK_SIZE 2112
+/* NFCv1 cannot read more that 7 bytes of ID */
+#define NFCV1_READID_LEN 7
+/* Polling is done at a pace of POLL_PERIOD us until POLL_TIMEOUT is reached */
+#define POLL_PERIOD 0
+#define POLL_TIMEOUT 100000
+/* Interrupt maximum wait period in ms */
+#define IRQ_TIMEOUT 1000
+/* Latency in clock cycles between SoC pins and NFC logic */
+#define MIN_RD_DEL_CNT 3
+/* Maximum number of contiguous address cycles */
+#define MAX_ADDRESS_CYC_NFCV1 5
+#define MAX_ADDRESS_CYC_NFCV2 7
+/* System control registers/bits to enable the NAND controller on some SoCs */
+#define GENCONF_SOC_DEVICE_MUX 0x208
+#define GENCONF_SOC_DEVICE_MUX_NFC_EN BIT(0)
+#define GENCONF_SOC_DEVICE_MUX_ECC_CLK_RST BIT(20)
+#define GENCONF_SOC_DEVICE_MUX_ECC_CORE_RST BIT(21)
+#define GENCONF_SOC_DEVICE_MUX_NFC_INT_EN BIT(25)
+#define GENCONF_CLK_GATING_CTRL 0x220
+#define GENCONF_CLK_GATING_CTRL_ND_GATE BIT(2)
+#define GENCONF_ND_CLK_CTRL 0x700
+#define GENCONF_ND_CLK_CTRL_EN BIT(0)
+
+/* NAND controller data flash control register */
+#define NDCR 0x00
+#define NDCR_ALL_INT GENMASK(11, 0)
+#define NDCR_CS1_CMDDM BIT(7)
+#define NDCR_CS0_CMDDM BIT(8)
+#define NDCR_RDYM BIT(11)
+#define NDCR_ND_ARB_EN BIT(12)
+#define NDCR_RA_START BIT(15)
+#define NDCR_RD_ID_CNT(x) (min_t(unsigned int, x, 0x7) << 16)
+#define NDCR_PAGE_SZ(x) (x >= 2048 ? BIT(24) : 0)
+#define NDCR_DWIDTH_M BIT(26)
+#define NDCR_DWIDTH_C BIT(27)
+#define NDCR_ND_RUN BIT(28)
+#define NDCR_DMA_EN BIT(29)
+#define NDCR_ECC_EN BIT(30)
+#define NDCR_SPARE_EN BIT(31)
+
+/* NAND interface timing parameter 0 register */
+#define NDTR0 0x04
+#define NDTR0_TRP(x) ((min_t(unsigned int, x, 0xF) & 0x7) << 0)
+#define NDTR0_TRH(x) (min_t(unsigned int, x, 0x7) << 3)
+#define NDTR0_ETRP(x) ((min_t(unsigned int, x, 0xF) & 0x8) << 3)
+#define NDTR0_SEL_NRE_EDGE BIT(7)
+#define NDTR0_TWP(x) (min_t(unsigned int, x, 0x7) << 8)
+#define NDTR0_TWH(x) (min_t(unsigned int, x, 0x7) << 11)
+#define NDTR0_TCS(x) (min_t(unsigned int, x, 0x7) << 16)
+#define NDTR0_TCH(x) (min_t(unsigned int, x, 0x7) << 19)
+#define NDTR0_RD_CNT_DEL(x) (min_t(unsigned int, x, 0xF) << 22)
+#define NDTR0_SELCNTR BIT(26)
+#define NDTR0_TADL(x) (min_t(unsigned int, x, 0x1F) << 27)
+
+/* NAND interface timing parameter 1 register */
+#define NDTR1 0x0C
+#define NDTR1_TAR(x) (min_t(unsigned int, x, 0xF) << 0)
+#define NDTR1_TWHR(x) (min_t(unsigned int, x, 0xF) << 4)
+#define NDTR1_TRHW(x) (min_t(unsigned int, x / 16, 0x3) << 8)
+#define NDTR1_PRESCALE BIT(14)
+#define NDTR1_WAIT_MODE BIT(15)
+#define NDTR1_TR(x) (min_t(unsigned int, x, 0xFFFF) << 16)
+
+/* NAND controller status register */
+#define NDSR 0x14
+#define NDSR_WRCMDREQ BIT(0)
+#define NDSR_RDDREQ BIT(1)
+#define NDSR_WRDREQ BIT(2)
+#define NDSR_CORERR BIT(3)
+#define NDSR_UNCERR BIT(4)
+#define NDSR_CMDD(cs) BIT(8 - cs)
+#define NDSR_RDY(rb) BIT(11 + rb)
+#define NDSR_ERRCNT(x) ((x >> 16) & 0x1F)
+
+/* NAND ECC control register */
+#define NDECCCTRL 0x28
+#define NDECCCTRL_BCH_EN BIT(0)
+
+/* NAND controller data buffer register */
+#define NDDB 0x40
+
+/* NAND controller command buffer 0 register */
+#define NDCB0 0x48
+#define NDCB0_CMD1(x) ((x & 0xFF) << 0)
+#define NDCB0_CMD2(x) ((x & 0xFF) << 8)
+#define NDCB0_ADDR_CYC(x) ((x & 0x7) << 16)
+#define NDCB0_DBC BIT(19)
+#define NDCB0_CMD_TYPE(x) ((x & 0x7) << 21)
+#define NDCB0_CSEL BIT(24)
+#define NDCB0_RDY_BYP BIT(27)
+#define NDCB0_LEN_OVRD BIT(28)
+#define NDCB0_CMD_XTYPE(x) ((x & 0x7) << 29)
+
+/* NAND controller command buffer 1 register */
+#define NDCB1 0x4C
+#define NDCB1_COLS(x) ((x & 0xFFFF) << 0)
+#define NDCB1_ADDRS_PAGE(x) (x << 16)
+
+/* NAND controller command buffer 2 register */
+#define NDCB2 0x50
+#define NDCB2_ADDR5_PAGE(x) (((x >> 16) & 0xFF) << 0)
+#define NDCB2_ADDR5_CYC(x) ((x & 0xFF) << 0)
+
+/* NAND controller command buffer 3 register */
+#define NDCB3 0x54
+#define NDCB3_ADDR6_CYC(x) ((x & 0xFF) << 16)
+#define NDCB3_ADDR7_CYC(x) ((x & 0xFF) << 24)
+
+/* NAND controller command buffer 0 register 'type' and 'xtype' fields */
+#define TYPE_READ 0
+#define TYPE_WRITE 1
+#define TYPE_ERASE 2
+#define TYPE_READ_ID 3
+#define TYPE_STATUS 4
+#define TYPE_RESET 5
+#define TYPE_NAKED_CMD 6
+#define TYPE_NAKED_ADDR 7
+#define TYPE_MASK 7
+#define XTYPE_MONOLITHIC_RW 0
+#define XTYPE_LAST_NAKED_RW 1
+#define XTYPE_FINAL_COMMAND 3
+#define XTYPE_READ 4
+#define XTYPE_WRITE_DISPATCH 4
+#define XTYPE_NAKED_RW 5
+#define XTYPE_COMMAND_DISPATCH 6
+#define XTYPE_MASK 7
+
+/**
+ * Marvell ECC engine works differently than the others, in order to limit the
+ * size of the IP, hardware engineers chose to set a fixed strength at 16 bits
+ * per subpage, and depending on a the desired strength needed by the NAND chip,
+ * a particular layout mixing data/spare/ecc is defined, with a possible last
+ * chunk smaller that the others.
+ *
+ * @writesize: Full page size on which the layout applies
+ * @chunk: Desired ECC chunk size on which the layout applies
+ * @strength: Desired ECC strength (per chunk size bytes) on which the
+ * layout applies
+ * @nchunks: Total number of chunks
+ * @full_chunk_cnt: Number of full-sized chunks, which is the number of
+ * repetitions of the pattern:
+ * (data_bytes + spare_bytes + ecc_bytes).
+ * @data_bytes: Number of data bytes per chunk
+ * @spare_bytes: Number of spare bytes per chunk
+ * @ecc_bytes: Number of ecc bytes per chunk
+ * @last_data_bytes: Number of data bytes in the last chunk
+ * @last_spare_bytes: Number of spare bytes in the last chunk
+ * @last_ecc_bytes: Number of ecc bytes in the last chunk
+ */
+struct marvell_hw_ecc_layout {
+ /* Constraints */
+ int writesize;
+ int chunk;
+ int strength;
+ /* Corresponding layout */
+ int nchunks;
+ int full_chunk_cnt;
+ int data_bytes;
+ int spare_bytes;
+ int ecc_bytes;
+ int last_data_bytes;
+ int last_spare_bytes;
+ int last_ecc_bytes;
+};
+
+#define MARVELL_LAYOUT(ws, dc, ds, nc, fcc, db, sb, eb, ldb, lsb, leb) \
+ { \
+ .writesize = ws, \
+ .chunk = dc, \
+ .strength = ds, \
+ .nchunks = nc, \
+ .full_chunk_cnt = fcc, \
+ .data_bytes = db, \
+ .spare_bytes = sb, \
+ .ecc_bytes = eb, \
+ .last_data_bytes = ldb, \
+ .last_spare_bytes = lsb, \
+ .last_ecc_bytes = leb, \
+ }
+
+/* Layouts explained in AN-379_Marvell_SoC_NFC_ECC */
+static const struct marvell_hw_ecc_layout marvell_nfc_layouts[] = {
+ MARVELL_LAYOUT( 512, 512, 1, 1, 1, 512, 8, 8, 0, 0, 0),
+ MARVELL_LAYOUT( 2048, 512, 1, 1, 1, 2048, 40, 24, 0, 0, 0),
+ MARVELL_LAYOUT( 2048, 512, 4, 1, 1, 2048, 32, 30, 0, 0, 0),
+ MARVELL_LAYOUT( 4096, 512, 4, 2, 2, 2048, 32, 30, 0, 0, 0),
+ MARVELL_LAYOUT( 4096, 512, 8, 5, 4, 1024, 0, 30, 0, 64, 30),
+};
+
+/**
+ * The Nand Flash Controller has up to 4 CE and 2 RB pins. The CE selection
+ * is made by a field in NDCB0 register, and in another field in NDCB2 register.
+ * The datasheet describes the logic with an error: ADDR5 field is once
+ * declared at the beginning of NDCB2, and another time at its end. Because the
+ * ADDR5 field of NDCB2 may be used by other bytes, it would be more logical
+ * to use the last bit of this field instead of the first ones.
+ *
+ * @cs: Wanted CE lane.
+ * @ndcb0_csel: Value of the NDCB0 register with or without the flag
+ * selecting the wanted CE lane. This is set once when
+ * the Device Tree is probed.
+ * @rb: Ready/Busy pin for the flash chip
+ */
+struct marvell_nand_chip_sel {
+ unsigned int cs;
+ u32 ndcb0_csel;
+ unsigned int rb;
+};
+
+/**
+ * NAND chip structure: stores NAND chip device related information
+ *
+ * @chip: Base NAND chip structure
+ * @node: Used to store NAND chips into a list
+ * @layout NAND layout when using hardware ECC
+ * @ndcr: Controller register value for this NAND chip
+ * @ndtr0: Timing registers 0 value for this NAND chip
+ * @ndtr1: Timing registers 1 value for this NAND chip
+ * @selected_die: Current active CS
+ * @nsels: Number of CS lines required by the NAND chip
+ * @sels: Array of CS lines descriptions
+ */
+struct marvell_nand_chip {
+ struct nand_chip chip;
+ struct list_head node;
+ const struct marvell_hw_ecc_layout *layout;
+ u32 ndcr;
+ u32 ndtr0;
+ u32 ndtr1;
+ int addr_cyc;
+ int selected_die;
+ unsigned int nsels;
+ struct marvell_nand_chip_sel sels[0];
+};
+
+static inline struct marvell_nand_chip *to_marvell_nand(struct nand_chip *chip)
+{
+ return container_of(chip, struct marvell_nand_chip, chip);
+}
+
+static inline struct marvell_nand_chip_sel *to_nand_sel(struct marvell_nand_chip
+ *nand)
+{
+ return &nand->sels[nand->selected_die];
+}
+
+/**
+ * NAND controller capabilities for distinction between compatible strings
+ *
+ * @max_cs_nb: Number of Chip Select lines available
+ * @max_rb_nb: Number of Ready/Busy lines available
+ * @need_system_controller: Indicates if the SoC needs to have access to the
+ * system controller (ie. to enable the NAND controller)
+ * @legacy_of_bindings: Indicates if DT parsing must be done using the old
+ * fashion way
+ * @is_nfcv2: NFCv2 has numerous enhancements compared to NFCv1, ie.
+ * BCH error detection and correction algorithm,
+ * NDCB3 register has been added
+ * @use_dma: Use dma for data transfers
+ */
+struct marvell_nfc_caps {
+ unsigned int max_cs_nb;
+ unsigned int max_rb_nb;
+ bool need_system_controller;
+ bool legacy_of_bindings;
+ bool is_nfcv2;
+ bool use_dma;
+};
+
+/**
+ * NAND controller structure: stores Marvell NAND controller information
+ *
+ * @controller: Base controller structure
+ * @dev: Parent device (used to print error messages)
+ * @regs: NAND controller registers
+ * @ecc_clk: ECC block clock, two times the NAND controller clock
+ * @complete: Completion object to wait for NAND controller events
+ * @assigned_cs: Bitmask describing already assigned CS lines
+ * @chips: List containing all the NAND chips attached to
+ * this NAND controller
+ * @caps: NAND controller capabilities for each compatible string
+ * @dma_chan: DMA channel (NFCv1 only)
+ * @dma_buf: 32-bit aligned buffer for DMA transfers (NFCv1 only)
+ */
+struct marvell_nfc {
+ struct nand_hw_control controller;
+ struct device *dev;
+ void __iomem *regs;
+ struct clk *ecc_clk;
+ struct completion complete;
+ unsigned long assigned_cs;
+ struct list_head chips;
+ struct nand_chip *selected_chip;
+ const struct marvell_nfc_caps *caps;
+
+ /* DMA (NFCv1 only) */
+ bool use_dma;
+ struct dma_chan *dma_chan;
+ u8 *dma_buf;
+};
+
+static inline struct marvell_nfc *to_marvell_nfc(struct nand_hw_control *ctrl)
+{
+ return container_of(ctrl, struct marvell_nfc, controller);
+}
+
+/**
+ * NAND controller timings expressed in NAND Controller clock cycles
+ *
+ * @tRP: ND_nRE pulse width
+ * @tRH: ND_nRE high duration
+ * @tWP: ND_nWE pulse time
+ * @tWH: ND_nWE high duration
+ * @tCS: Enable signal setup time
+ * @tCH: Enable signal hold time
+ * @tADL: Address to write data delay
+ * @tAR: ND_ALE low to ND_nRE low delay
+ * @tWHR: ND_nWE high to ND_nRE low for status read
+ * @tRHW: ND_nRE high duration, read to write delay
+ * @tR: ND_nWE high to ND_nRE low for read
+ */
+struct marvell_nfc_timings {
+ /* NDTR0 fields */
+ unsigned int tRP;
+ unsigned int tRH;
+ unsigned int tWP;
+ unsigned int tWH;
+ unsigned int tCS;
+ unsigned int tCH;
+ unsigned int tADL;
+ /* NDTR1 fields */
+ unsigned int tAR;
+ unsigned int tWHR;
+ unsigned int tRHW;
+ unsigned int tR;
+};
+
+/**
+ * Derives a duration in numbers of clock cycles.
+ *
+ * @ps: Duration in pico-seconds
+ * @period_ns: Clock period in nano-seconds
+ *
+ * Convert the duration in nano-seconds, then divide by the period and
+ * return the number of clock periods.
+ */
+#define TO_CYCLES(ps, period_ns) (DIV_ROUND_UP(ps / 1000, period_ns))
+
+/**
+ * NAND driver structure filled during the parsing of the ->exec_op() subop
+ * subset of instructions.
+ *
+ * @ndcb: Array of values written to NDCBx registers
+ * @cle_ale_delay_ns: Optional delay after the last CMD or ADDR cycle
+ * @rdy_timeout_ms: Timeout for waits on Ready/Busy pin
+ * @rdy_delay_ns: Optional delay after waiting for the RB pin
+ * @data_delay_ns: Optional delay after the data xfer
+ * @data_instr_idx: Index of the data instruction in the subop
+ * @data_instr: Pointer to the data instruction in the subop
+ */
+struct marvell_nfc_op {
+ u32 ndcb[4];
+ unsigned int cle_ale_delay_ns;
+ unsigned int rdy_timeout_ms;
+ unsigned int rdy_delay_ns;
+ unsigned int data_delay_ns;
+ unsigned int data_instr_idx;
+ const struct nand_op_instr *data_instr;
+};
+
+/*
+ * Internal helper to conditionnally apply a delay (from the above structure,
+ * most of the time).
+ */
+static void cond_delay(unsigned int ns)
+{
+ if (!ns)
+ return;
+
+ if (ns < 10000)
+ ndelay(ns);
+ else
+ udelay(DIV_ROUND_UP(ns, 1000));
+}
+
+/*
+ * The controller has many flags that could generate interrupts, most of them
+ * are disabled and polling is used. For the very slow signals, using interrupts
+ * may relax the CPU charge.
+ */
+static void marvell_nfc_disable_int(struct marvell_nfc *nfc, u32 int_mask)
+{
+ u32 reg;
+
+ /* Writing 1 disables the interrupt */
+ reg = readl_relaxed(nfc->regs + NDCR);
+ writel_relaxed(reg | int_mask, nfc->regs + NDCR);
+}
+
+static void marvell_nfc_enable_int(struct marvell_nfc *nfc, u32 int_mask)
+{
+ u32 reg;
+
+ /* Writing 0 enables the interrupt */
+ reg = readl_relaxed(nfc->regs + NDCR);
+ writel_relaxed(reg & ~int_mask, nfc->regs + NDCR);
+}
+
+static void marvell_nfc_clear_int(struct marvell_nfc *nfc, u32 int_mask)
+{
+ writel_relaxed(int_mask, nfc->regs + NDSR);
+}
+
+static void marvell_nfc_force_byte_access(struct nand_chip *chip,
+ bool force_8bit)
+{
+ struct marvell_nfc *nfc = to_marvell_nfc(chip->controller);
+ u32 ndcr;
+
+ /*
+ * Callers of this function do not verify if the NAND is using a 16-bit
+ * an 8-bit bus for normal operations, so we need to take care of that
+ * here by leaving the configuration unchanged if the NAND does not have
+ * the NAND_BUSWIDTH_16 flag set.
+ */
+ if (!(chip->options & NAND_BUSWIDTH_16))
+ return;
+
+ ndcr = readl_relaxed(nfc->regs + NDCR);
+
+ if (force_8bit)
+ ndcr &= ~(NDCR_DWIDTH_M | NDCR_DWIDTH_C);
+ else
+ ndcr |= NDCR_DWIDTH_M | NDCR_DWIDTH_C;
+
+ writel_relaxed(ndcr, nfc->regs + NDCR);
+}
+
+static int marvell_nfc_wait_ndrun(struct nand_chip *chip)
+{
+ struct marvell_nfc *nfc = to_marvell_nfc(chip->controller);
+ u32 val;
+ int ret;
+
+ /*
+ * The command is being processed, wait for the ND_RUN bit to be
+ * cleared by the NFC. If not, we must clear it by hand.
+ */
+ ret = readl_relaxed_poll_timeout(nfc->regs + NDCR, val,
+ (val & NDCR_ND_RUN) == 0,
+ POLL_PERIOD, POLL_TIMEOUT);
+ if (ret) {
+ dev_err(nfc->dev, "Timeout on NAND controller run mode\n");
+ writel_relaxed(readl(nfc->regs + NDCR) & ~NDCR_ND_RUN,
+ nfc->regs + NDCR);
+ return ret;
+ }
+
+ return 0;
+}
+
+/*
+ * Any time a command has to be sent to the controller, the following sequence
+ * has to be followed:
+ * - call marvell_nfc_prepare_cmd()
+ * -> activate the ND_RUN bit that will kind of 'start a job'
+ * -> wait the signal indicating the NFC is waiting for a command
+ * - send the command (cmd and address cycles)
+ * - enventually send or receive the data
+ * - call marvell_nfc_end_cmd() with the corresponding flag
+ * -> wait the flag to be triggered or cancel the job with a timeout
+ *
+ * The following helpers are here to factorize the code a bit so that
+ * specialized functions responsible for executing the actual NAND
+ * operations do not have to replicate the same code blocks.
+ */
+static int marvell_nfc_prepare_cmd(struct nand_chip *chip)
+{
+ struct marvell_nfc *nfc = to_marvell_nfc(chip->controller);
+ u32 ndcr, val;
+ int ret;
+
+ /* Poll ND_RUN and clear NDSR before issuing any command */
+ ret = marvell_nfc_wait_ndrun(chip);
+ if (ret) {
+ dev_err(nfc->dev, "Last operation did not suceed\n");
+ return ret;
+ }
+
+ ndcr = readl_relaxed(nfc->regs + NDCR);
+ writel_relaxed(readl(nfc->regs + NDSR), nfc->regs + NDSR);
+
+ /* Assert ND_RUN bit and wait the NFC to be ready */
+ writel_relaxed(ndcr | NDCR_ND_RUN, nfc->regs + NDCR);
+ ret = readl_relaxed_poll_timeout(nfc->regs + NDSR, val,
+ val & NDSR_WRCMDREQ,
+ POLL_PERIOD, POLL_TIMEOUT);
+ if (ret) {
+ dev_err(nfc->dev, "Timeout on WRCMDRE\n");
+ return -ETIMEDOUT;
+ }
+
+ /* Command may be written, clear WRCMDREQ status bit */
+ writel_relaxed(NDSR_WRCMDREQ, nfc->regs + NDSR);
+
+ return 0;
+}
+
+static void marvell_nfc_send_cmd(struct nand_chip *chip,
+ struct marvell_nfc_op *nfc_op)
+{
+ struct marvell_nand_chip *marvell_nand = to_marvell_nand(chip);
+ struct marvell_nfc *nfc = to_marvell_nfc(chip->controller);
+
+ dev_dbg(nfc->dev, "\nNDCR: 0x%08x\n"
+ "NDCB0: 0x%08x\nNDCB1: 0x%08x\nNDCB2: 0x%08x\nNDCB3: 0x%08x\n",
+ (u32)readl_relaxed(nfc->regs + NDCR), nfc_op->ndcb[0],
+ nfc_op->ndcb[1], nfc_op->ndcb[2], nfc_op->ndcb[3]);
+
+ writel_relaxed(to_nand_sel(marvell_nand)->ndcb0_csel | nfc_op->ndcb[0],
+ nfc->regs + NDCB0);
+ writel_relaxed(nfc_op->ndcb[1], nfc->regs + NDCB0);
+ writel(nfc_op->ndcb[2], nfc->regs + NDCB0);
+
+ /*
+ * Write NDCB0 four times only if LEN_OVRD is set or if ADDR6 or ADDR7
+ * fields are used (only available on NFCv2).
+ */
+ if (nfc_op->ndcb[0] & NDCB0_LEN_OVRD ||
+ (nfc_op->ndcb[0] & NDCB0_ADDR_CYC(6)) == NDCB0_ADDR_CYC(6)) {
+ if (nfc->caps->is_nfcv2)
+ writel(nfc_op->ndcb[3], nfc->regs + NDCB0);
+ else
+ dev_err(nfc->dev,
+ "NDCB3 does not exist on NFCv1 and should not be written\n");
+ }
+}
+
+static int marvell_nfc_end_cmd(struct nand_chip *chip, int flag,
+ const char *label)
+{
+ struct marvell_nfc *nfc = to_marvell_nfc(chip->controller);
+ u32 val;
+ int ret;
+
+ ret = readl_relaxed_poll_timeout(nfc->regs + NDSR, val,
+ val & flag,
+ POLL_PERIOD, POLL_TIMEOUT);
+
+ if (ret) {
+ dev_err(nfc->dev, "Timeout on %s (NDSR: 0x%08x)\n",
+ label, val);
+ if (nfc->dma_chan)
+ dmaengine_terminate_all(nfc->dma_chan);
+ return ret;
+ }
+
+ /*
+ * DMA function uses this helper to poll on CMDD bits without wanting
+ * them to be bleared.
+ */
+ if (nfc->use_dma && (readl_relaxed(nfc->regs + NDCR) & NDCR_DMA_EN))
+ return 0;
+
+ writel_relaxed(flag, nfc->regs + NDSR);
+
+ return 0;
+}
+
+static int marvell_nfc_wait_cmdd(struct nand_chip *chip)
+{
+ struct marvell_nand_chip *marvell_nand = to_marvell_nand(chip);
+ int cs_flag = NDSR_CMDD(to_nand_sel(marvell_nand)->ndcb0_csel);
+
+ return marvell_nfc_end_cmd(chip, cs_flag, "CMDD");
+}
+
+static int marvell_nfc_wait_op(struct nand_chip *chip, unsigned int timeout_ms)
+{
+ struct marvell_nfc *nfc = to_marvell_nfc(chip->controller);
+ int ret;
+
+ /* Timeout is expressed in ms */
+ if (!timeout_ms)
+ timeout_ms = IRQ_TIMEOUT;
+
+ init_completion(&nfc->complete);
+
+ marvell_nfc_enable_int(nfc, NDCR_RDYM);
+ ret = wait_for_completion_timeout(&nfc->complete,
+ msecs_to_jiffies(timeout_ms));
+ marvell_nfc_disable_int(nfc, NDCR_RDYM);
+ marvell_nfc_clear_int(nfc, NDSR_RDY(0) | NDSR_RDY(1));
+ if (!ret) {
+ dev_err(nfc->dev, "Timeout waiting for RB signal\n");
+ return -ETIMEDOUT;
+ }
+
+ return 0;
+}
+
+static void marvell_nfc_select_chip(struct mtd_info *mtd, int die_nr)
+{
+ struct nand_chip *chip = mtd_to_nand(mtd);
+ struct marvell_nand_chip *marvell_nand = to_marvell_nand(chip);
+ struct marvell_nfc *nfc = to_marvell_nfc(chip->controller);
+
+ if (chip == nfc->selected_chip && die_nr == marvell_nand->selected_die)
+ return;
+
+ if (die_nr < 0 || die_nr >= marvell_nand->nsels) {
+ nfc->selected_chip = NULL;
+ marvell_nand->selected_die = -1;
+ return;
+ }
+
+ /*
+ * Do not change the timing registers when using the DT property
+ * marvell,nand-keep-config; in that case ->ndtr0 and ->ndtr1 from the
+ * marvell_nand structure are supposedly empty.
+ */
+ if (marvell_nand->ndtr0 && marvell_nand->ndtr1) {
+ writel_relaxed(marvell_nand->ndtr0, nfc->regs + NDTR0);
+ writel_relaxed(marvell_nand->ndtr1, nfc->regs + NDTR1);
+ }
+
+ /* Reset the NDCR register to a clean state for this particular chip */
+ if (marvell_nand->ndcr)
+ writel_relaxed(marvell_nand->ndcr, nfc->regs + NDCR);
+
+ /* Also reset the interrupt status register */
+ marvell_nfc_clear_int(nfc, NDCR_ALL_INT);
+
+ nfc->selected_chip = chip;
+ marvell_nand->selected_die = die_nr;
+}
+
+static irqreturn_t marvell_nfc_isr(int irq, void *dev_id)
+{
+ struct marvell_nfc *nfc = dev_id;
+ u32 st = readl_relaxed(nfc->regs + NDSR);
+ u32 ien = (~readl_relaxed(nfc->regs + NDCR)) & NDCR_ALL_INT;
+
+ /*
+ * RDY interrupt mask is one bit in NDCR while there are two status
+ * bit in NDSR (RDY[cs0/cs2] and RDY[cs1/cs3]).
+ */
+ if (st & NDSR_RDY(1))
+ st |= NDSR_RDY(0);
+
+ if (!(st & ien))
+ return IRQ_NONE;
+
+ marvell_nfc_disable_int(nfc, st & NDCR_ALL_INT);
+
+ if (!(st & (NDSR_RDDREQ | NDSR_WRDREQ | NDSR_WRCMDREQ)))
+ complete(&nfc->complete);
+
+ return IRQ_HANDLED;
+}
+
+/* HW ECC related functions */
+static void marvell_nfc_enable_hw_ecc(struct nand_chip *chip)
+{
+ struct marvell_nfc *nfc = to_marvell_nfc(chip->controller);
+ u32 ndcr = readl_relaxed(nfc->regs + NDCR);
+
+ if (!(ndcr & NDCR_ECC_EN)) {
+ writel_relaxed(ndcr | NDCR_ECC_EN, nfc->regs + NDCR);
+
+ /*
+ * When enabling BCH, set threshold to 0 to always know the
+ * number of corrected bitflips.
+ */
+ if (chip->ecc.algo == NAND_ECC_BCH)
+ writel_relaxed(NDECCCTRL_BCH_EN, nfc->regs + NDECCCTRL);
+ }
+}
+
+static void marvell_nfc_disable_hw_ecc(struct nand_chip *chip)
+{
+ struct marvell_nfc *nfc = to_marvell_nfc(chip->controller);
+ u32 ndcr = readl_relaxed(nfc->regs + NDCR);
+
+ if (ndcr & NDCR_ECC_EN) {
+ writel_relaxed(ndcr & ~NDCR_ECC_EN, nfc->regs + NDCR);
+ if (chip->ecc.algo == NAND_ECC_BCH)
+ writel_relaxed(0, nfc->regs + NDECCCTRL);
+ }
+}
+
+/* DMA related helpers */
+static void marvell_nfc_enable_dma(struct marvell_nfc *nfc)
+{
+ u32 reg;
+
+ reg = readl_relaxed(nfc->regs + NDCR);
+ writel_relaxed(reg | NDCR_DMA_EN, nfc->regs + NDCR);
+}
+
+static void marvell_nfc_disable_dma(struct marvell_nfc *nfc)
+{
+ u32 reg;
+
+ reg = readl_relaxed(nfc->regs + NDCR);
+ writel_relaxed(reg & ~NDCR_DMA_EN, nfc->regs + NDCR);
+}
+
+/* Read/write PIO/DMA accessors */
+static int marvell_nfc_xfer_data_dma(struct marvell_nfc *nfc,
+ enum dma_data_direction direction,
+ unsigned int len)
+{
+ unsigned int dma_len = min_t(int, ALIGN(len, 32), MAX_CHUNK_SIZE);
+ struct dma_async_tx_descriptor *tx;
+ struct scatterlist sg;
+ dma_cookie_t cookie;
+ int ret;
+
+ marvell_nfc_enable_dma(nfc);
+ /* Prepare the DMA transfer */
+ sg_init_one(&sg, nfc->dma_buf, dma_len);
+ dma_map_sg(nfc->dma_chan->device->dev, &sg, 1, direction);
+ tx = dmaengine_prep_slave_sg(nfc->dma_chan, &sg, 1,
+ direction == DMA_FROM_DEVICE ?
+ DMA_DEV_TO_MEM : DMA_MEM_TO_DEV,
+ DMA_PREP_INTERRUPT);
+ if (!tx) {
+ dev_err(nfc->dev, "Could not prepare DMA S/G list\n");
+ return -ENXIO;
+ }
+
+ /* Do the task and wait for it to finish */
+ cookie = dmaengine_submit(tx);
+ ret = dma_submit_error(cookie);
+ if (ret)
+ return -EIO;
+
+ dma_async_issue_pending(nfc->dma_chan);
+ ret = marvell_nfc_wait_cmdd(nfc->selected_chip);
+ dma_unmap_sg(nfc->dma_chan->device->dev, &sg, 1, direction);
+ marvell_nfc_disable_dma(nfc);
+ if (ret) {
+ dev_err(nfc->dev, "Timeout waiting for DMA (status: %d)\n",
+ dmaengine_tx_status(nfc->dma_chan, cookie, NULL));
+ dmaengine_terminate_all(nfc->dma_chan);
+ return -ETIMEDOUT;
+ }
+
+ return 0;
+}
+
+static int marvell_nfc_xfer_data_in_pio(struct marvell_nfc *nfc, u8 *in,
+ unsigned int len)
+{
+ unsigned int last_len = len % FIFO_DEPTH;
+ unsigned int last_full_offset = round_down(len, FIFO_DEPTH);
+ int i;
+
+ for (i = 0; i < last_full_offset; i += FIFO_DEPTH)
+ ioread32_rep(nfc->regs + NDDB, in + i, FIFO_REP(FIFO_DEPTH));
+
+ if (last_len) {
+ u8 tmp_buf[FIFO_DEPTH];
+
+ ioread32_rep(nfc->regs + NDDB, tmp_buf, FIFO_REP(FIFO_DEPTH));
+ memcpy(in + last_full_offset, tmp_buf, last_len);
+ }
+
+ return 0;
+}
+
+static int marvell_nfc_xfer_data_out_pio(struct marvell_nfc *nfc, const u8 *out,
+ unsigned int len)
+{
+ unsigned int last_len = len % FIFO_DEPTH;
+ unsigned int last_full_offset = round_down(len, FIFO_DEPTH);
+ int i;
+
+ for (i = 0; i < last_full_offset; i += FIFO_DEPTH)
+ iowrite32_rep(nfc->regs + NDDB, out + i, FIFO_REP(FIFO_DEPTH));
+
+ if (last_len) {
+ u8 tmp_buf[FIFO_DEPTH];
+
+ memcpy(tmp_buf, out + last_full_offset, last_len);
+ iowrite32_rep(nfc->regs + NDDB, tmp_buf, FIFO_REP(FIFO_DEPTH));
+ }
+
+ return 0;
+}
+
+static void marvell_nfc_check_empty_chunk(struct nand_chip *chip,
+ u8 *data, int data_len,
+ u8 *spare, int spare_len,
+ u8 *ecc, int ecc_len,
+ unsigned int *max_bitflips)
+{
+ struct mtd_info *mtd = nand_to_mtd(chip);
+ int bf;
+
+ /*
+ * Blank pages (all 0xFF) that have not been written may be recognized
+ * as bad if bitflips occur, so whenever an uncorrectable error occurs,
+ * check if the entire page (with ECC bytes) is actually blank or not.
+ */
+ if (!data)
+ data_len = 0;
+ if (!spare)
+ spare_len = 0;
+ if (!ecc)
+ ecc_len = 0;
+
+ bf = nand_check_erased_ecc_chunk(data, data_len, ecc, ecc_len,
+ spare, spare_len, chip->ecc.strength);
+ if (bf < 0) {
+ mtd->ecc_stats.failed++;
+ return;
+ }
+
+ /* Update the stats and max_bitflips */
+ mtd->ecc_stats.corrected += bf;
+ *max_bitflips = max_t(unsigned int, *max_bitflips, bf);
+}
+
+/*
+ * Check a chunk is correct or not according to hardware ECC engine.
+ * mtd->ecc_stats.corrected is updated, as well as max_bitflips, however
+ * mtd->ecc_stats.failure is not, the function will instead return a non-zero
+ * value indicating that a check on the emptyness of the subpage must be
+ * performed before declaring the subpage corrupted.
+ */
+static int marvell_nfc_hw_ecc_correct(struct nand_chip *chip,
+ unsigned int *max_bitflips)
+{
+ struct mtd_info *mtd = nand_to_mtd(chip);
+ struct marvell_nfc *nfc = to_marvell_nfc(chip->controller);
+ int bf = 0;
+ u32 ndsr;
+
+ ndsr = readl_relaxed(nfc->regs + NDSR);
+
+ /* Check uncorrectable error flag */
+ if (ndsr & NDSR_UNCERR) {
+ writel_relaxed(ndsr, nfc->regs + NDSR);
+
+ /*
+ * Do not increment ->ecc_stats.failed now, instead, return a
+ * non-zero value to indicate that this chunk was apparently
+ * bad, and it should be check to see if it empty or not. If
+ * the chunk (with ECC bytes) is not declared empty, the calling
+ * function must increment the failure count.
+ */
+ return -EBADMSG;
+ }
+
+ /* Check correctable error flag */
+ if (ndsr & NDSR_CORERR) {
+ writel_relaxed(ndsr, nfc->regs + NDSR);
+
+ if (chip->ecc.algo == NAND_ECC_BCH)
+ bf = NDSR_ERRCNT(ndsr);
+ else
+ bf = 1;
+ }
+
+ /* Update the stats and max_bitflips */
+ mtd->ecc_stats.corrected += bf;
+ *max_bitflips = max_t(unsigned int, *max_bitflips, bf);
+
+ return 0;
+}
+
+/* Hamming read helpers */
+static int marvell_nfc_hw_ecc_hmg_do_read_page(struct nand_chip *chip,
+ u8 *data_buf, u8 *oob_buf,
+ bool raw, int page)
+{
+ struct marvell_nand_chip *marvell_nand = to_marvell_nand(chip);
+ struct marvell_nfc *nfc = to_marvell_nfc(chip->controller);
+ const struct marvell_hw_ecc_layout *lt = to_marvell_nand(chip)->layout;
+ struct marvell_nfc_op nfc_op = {
+ .ndcb[0] = NDCB0_CMD_TYPE(TYPE_READ) |
+ NDCB0_ADDR_CYC(marvell_nand->addr_cyc) |
+ NDCB0_DBC |
+ NDCB0_CMD1(NAND_CMD_READ0) |
+ NDCB0_CMD2(NAND_CMD_READSTART),
+ .ndcb[1] = NDCB1_ADDRS_PAGE(page),
+ .ndcb[2] = NDCB2_ADDR5_PAGE(page),
+ };
+ unsigned int oob_bytes = lt->spare_bytes + (raw ? lt->ecc_bytes : 0);
+ int ret;
+
+ /* NFCv2 needs more information about the operation being executed */
+ if (nfc->caps->is_nfcv2)
+ nfc_op.ndcb[0] |= NDCB0_CMD_XTYPE(XTYPE_MONOLITHIC_RW);
+
+ ret = marvell_nfc_prepare_cmd(chip);
+ if (ret)
+ return ret;
+
+ marvell_nfc_send_cmd(chip, &nfc_op);
+ ret = marvell_nfc_end_cmd(chip, NDSR_RDDREQ,
+ "RDDREQ while draining FIFO (data/oob)");
+ if (ret)
+ return ret;
+
+ /*
+ * Read the page then the OOB area. Unlike what is shown in current
+ * documentation, spare bytes are protected by the ECC engine, and must
+ * be at the beginning of the OOB area or running this driver on legacy
+ * systems will prevent the discovery of the BBM/BBT.
+ */
+ if (nfc->use_dma) {
+ marvell_nfc_xfer_data_dma(nfc, DMA_FROM_DEVICE,
+ lt->data_bytes + oob_bytes);
+ memcpy(data_buf, nfc->dma_buf, lt->data_bytes);
+ memcpy(oob_buf, nfc->dma_buf + lt->data_bytes, oob_bytes);
+ } else {
+ marvell_nfc_xfer_data_in_pio(nfc, data_buf, lt->data_bytes);
+ marvell_nfc_xfer_data_in_pio(nfc, oob_buf, oob_bytes);
+ }
+
+ ret = marvell_nfc_wait_cmdd(chip);
+
+ return ret;
+}
+
+static int marvell_nfc_hw_ecc_hmg_read_page_raw(struct mtd_info *mtd,
+ struct nand_chip *chip, u8 *buf,
+ int oob_required, int page)
+{
+ return marvell_nfc_hw_ecc_hmg_do_read_page(chip, buf, chip->oob_poi,
+ true, page);
+}
+
+static int marvell_nfc_hw_ecc_hmg_read_page(struct mtd_info *mtd,
+ struct nand_chip *chip,
+ u8 *buf, int oob_required,
+ int page)
+{
+ const struct marvell_hw_ecc_layout *lt = to_marvell_nand(chip)->layout;
+ unsigned int full_sz = lt->data_bytes + lt->spare_bytes + lt->ecc_bytes;
+ int max_bitflips = 0, ret;
+ u8 *raw_buf;
+
+ marvell_nfc_enable_hw_ecc(chip);
+ marvell_nfc_hw_ecc_hmg_do_read_page(chip, buf, chip->oob_poi, false,
+ page);
+ ret = marvell_nfc_hw_ecc_correct(chip, &max_bitflips);
+ marvell_nfc_disable_hw_ecc(chip);
+
+ if (!ret)
+ return max_bitflips;
+
+ /*
+ * When ECC failures are detected, check if the full page has been
+ * written or not. Ignore the failure if it is actually empty.
+ */
+ raw_buf = kmalloc(full_sz, GFP_KERNEL);
+ if (!raw_buf)
+ return -ENOMEM;
+
+ marvell_nfc_hw_ecc_hmg_do_read_page(chip, raw_buf, raw_buf +
+ lt->data_bytes, true, page);
+ marvell_nfc_check_empty_chunk(chip, raw_buf, full_sz, NULL, 0, NULL, 0,
+ &max_bitflips);
+ kfree(raw_buf);
+
+ return max_bitflips;
+}
+
+/*
+ * Spare area in Hamming layouts is not protected by the ECC engine (even if
+ * it appears before the ECC bytes when reading), the ->read_oob_raw() function
+ * also stands for ->read_oob().
+ */
+static int marvell_nfc_hw_ecc_hmg_read_oob_raw(struct mtd_info *mtd,
+ struct nand_chip *chip, int page)
+{
+ /* Invalidate page cache */
+ chip->pagebuf = -1;
+
+ return marvell_nfc_hw_ecc_hmg_do_read_page(chip, chip->data_buf,
+ chip->oob_poi, true, page);
+}
+
+/* Hamming write helpers */
+static int marvell_nfc_hw_ecc_hmg_do_write_page(struct nand_chip *chip,
+ const u8 *data_buf,
+ const u8 *oob_buf, bool raw,
+ int page)
+{
+ struct marvell_nand_chip *marvell_nand = to_marvell_nand(chip);
+ struct marvell_nfc *nfc = to_marvell_nfc(chip->controller);
+ const struct marvell_hw_ecc_layout *lt = to_marvell_nand(chip)->layout;
+ struct marvell_nfc_op nfc_op = {
+ .ndcb[0] = NDCB0_CMD_TYPE(TYPE_WRITE) |
+ NDCB0_ADDR_CYC(marvell_nand->addr_cyc) |
+ NDCB0_CMD1(NAND_CMD_SEQIN) |
+ NDCB0_CMD2(NAND_CMD_PAGEPROG) |
+ NDCB0_DBC,
+ .ndcb[1] = NDCB1_ADDRS_PAGE(page),
+ .ndcb[2] = NDCB2_ADDR5_PAGE(page),
+ };
+ unsigned int oob_bytes = lt->spare_bytes + (raw ? lt->ecc_bytes : 0);
+ int ret;
+
+ /* NFCv2 needs more information about the operation being executed */
+ if (nfc->caps->is_nfcv2)
+ nfc_op.ndcb[0] |= NDCB0_CMD_XTYPE(XTYPE_MONOLITHIC_RW);
+
+ ret = marvell_nfc_prepare_cmd(chip);
+ if (ret)
+ return ret;
+
+ marvell_nfc_send_cmd(chip, &nfc_op);
+ ret = marvell_nfc_end_cmd(chip, NDSR_WRDREQ,
+ "WRDREQ while loading FIFO (data)");
+ if (ret)
+ return ret;
+
+ /* Write the page then the OOB area */
+ if (nfc->use_dma) {
+ memcpy(nfc->dma_buf, data_buf, lt->data_bytes);
+ memcpy(nfc->dma_buf + lt->data_bytes, oob_buf, oob_bytes);
+ marvell_nfc_xfer_data_dma(nfc, DMA_TO_DEVICE, lt->data_bytes +
+ lt->ecc_bytes + lt->spare_bytes);
+ } else {
+ marvell_nfc_xfer_data_out_pio(nfc, data_buf, lt->data_bytes);
+ marvell_nfc_xfer_data_out_pio(nfc, oob_buf, oob_bytes);
+ }
+
+ ret = marvell_nfc_wait_cmdd(chip);
+ if (ret)
+ return ret;
+
+ ret = marvell_nfc_wait_op(chip,
+ chip->data_interface.timings.sdr.tPROG_max);
+ return ret;
+}
+
+static int marvell_nfc_hw_ecc_hmg_write_page_raw(struct mtd_info *mtd,
+ struct nand_chip *chip,
+ const u8 *buf,
+ int oob_required, int page)
+{
+ return marvell_nfc_hw_ecc_hmg_do_write_page(chip, buf, chip->oob_poi,
+ true, page);
+}
+
+static int marvell_nfc_hw_ecc_hmg_write_page(struct mtd_info *mtd,
+ struct nand_chip *chip,
+ const u8 *buf,
+ int oob_required, int page)
+{
+ int ret;
+
+ marvell_nfc_enable_hw_ecc(chip);
+ ret = marvell_nfc_hw_ecc_hmg_do_write_page(chip, buf, chip->oob_poi,
+ false, page);
+ marvell_nfc_disable_hw_ecc(chip);
+
+ return ret;
+}
+
+/*
+ * Spare area in Hamming layouts is not protected by the ECC engine (even if
+ * it appears before the ECC bytes when reading), the ->write_oob_raw() function
+ * also stands for ->write_oob().
+ */
+static int marvell_nfc_hw_ecc_hmg_write_oob_raw(struct mtd_info *mtd,
+ struct nand_chip *chip,
+ int page)
+{
+ /* Invalidate page cache */
+ chip->pagebuf = -1;
+
+ memset(chip->data_buf, 0xFF, mtd->writesize);
+
+ return marvell_nfc_hw_ecc_hmg_do_write_page(chip, chip->data_buf,
+ chip->oob_poi, true, page);
+}
+
+/* BCH read helpers */
+static int marvell_nfc_hw_ecc_bch_read_page_raw(struct mtd_info *mtd,
+ struct nand_chip *chip, u8 *buf,
+ int oob_required, int page)
+{
+ const struct marvell_hw_ecc_layout *lt = to_marvell_nand(chip)->layout;
+ u8 *oob = chip->oob_poi;
+ int chunk_size = lt->data_bytes + lt->spare_bytes + lt->ecc_bytes;
+ int ecc_offset = (lt->full_chunk_cnt * lt->spare_bytes) +
+ lt->last_spare_bytes;
+ int data_len = lt->data_bytes;
+ int spare_len = lt->spare_bytes;
+ int ecc_len = lt->ecc_bytes;
+ int chunk;
+
+ if (oob_required)
+ memset(chip->oob_poi, 0xFF, mtd->oobsize);
+
+ nand_read_page_op(chip, page, 0, NULL, 0);
+
+ for (chunk = 0; chunk < lt->nchunks; chunk++) {
+ /* Update last chunk length */
+ if (chunk >= lt->full_chunk_cnt) {
+ data_len = lt->last_data_bytes;
+ spare_len = lt->last_spare_bytes;
+ ecc_len = lt->last_ecc_bytes;
+ }
+
+ /* Read data bytes*/
+ nand_change_read_column_op(chip, chunk * chunk_size,
+ buf + (lt->data_bytes * chunk),
+ data_len, false);
+
+ /* Read spare bytes */
+ nand_read_data_op(chip, oob + (lt->spare_bytes * chunk),
+ spare_len, false);
+
+ /* Read ECC bytes */
+ nand_read_data_op(chip, oob + ecc_offset +
+ (ALIGN(lt->ecc_bytes, 32) * chunk),
+ ecc_len, false);
+ }
+
+ return 0;
+}
+
+static void marvell_nfc_hw_ecc_bch_read_chunk(struct nand_chip *chip, int chunk,
+ u8 *data, unsigned int data_len,
+ u8 *spare, unsigned int spare_len,
+ int page)
+{
+ struct marvell_nand_chip *marvell_nand = to_marvell_nand(chip);
+ struct marvell_nfc *nfc = to_marvell_nfc(chip->controller);
+ const struct marvell_hw_ecc_layout *lt = to_marvell_nand(chip)->layout;
+ int i, ret;
+ struct marvell_nfc_op nfc_op = {
+ .ndcb[0] = NDCB0_CMD_TYPE(TYPE_READ) |
+ NDCB0_ADDR_CYC(marvell_nand->addr_cyc) |
+ NDCB0_LEN_OVRD,
+ .ndcb[1] = NDCB1_ADDRS_PAGE(page),
+ .ndcb[2] = NDCB2_ADDR5_PAGE(page),
+ .ndcb[3] = data_len + spare_len,
+ };
+
+ ret = marvell_nfc_prepare_cmd(chip);
+ if (ret)
+ return;
+
+ if (chunk == 0)
+ nfc_op.ndcb[0] |= NDCB0_DBC |
+ NDCB0_CMD1(NAND_CMD_READ0) |
+ NDCB0_CMD2(NAND_CMD_READSTART);
+
+ /*
+ * Trigger the naked read operation only on the last chunk.
+ * Otherwise, use monolithic read.
+ */
+ if (lt->nchunks == 1 || (chunk < lt->nchunks - 1))
+ nfc_op.ndcb[0] |= NDCB0_CMD_XTYPE(XTYPE_MONOLITHIC_RW);
+ else
+ nfc_op.ndcb[0] |= NDCB0_CMD_XTYPE(XTYPE_LAST_NAKED_RW);
+
+ marvell_nfc_send_cmd(chip, &nfc_op);
+
+ /*
+ * According to the datasheet, when reading from NDDB
+ * with BCH enabled, after each 32 bytes reads, we
+ * have to make sure that the NDSR.RDDREQ bit is set.
+ *
+ * Drain the FIFO, 8 32-bit reads at a time, and skip
+ * the polling on the last read.
+ *
+ * Length is a multiple of 32 bytes, hence it is a multiple of 8 too.
+ */
+ for (i = 0; i < data_len; i += FIFO_DEPTH * BCH_SEQ_READS) {
+ marvell_nfc_end_cmd(chip, NDSR_RDDREQ,
+ "RDDREQ while draining FIFO (data)");
+ marvell_nfc_xfer_data_in_pio(nfc, data,
+ FIFO_DEPTH * BCH_SEQ_READS);
+ data += FIFO_DEPTH * BCH_SEQ_READS;
+ }
+
+ for (i = 0; i < spare_len; i += FIFO_DEPTH * BCH_SEQ_READS) {
+ marvell_nfc_end_cmd(chip, NDSR_RDDREQ,
+ "RDDREQ while draining FIFO (OOB)");
+ marvell_nfc_xfer_data_in_pio(nfc, spare,
+ FIFO_DEPTH * BCH_SEQ_READS);
+ spare += FIFO_DEPTH * BCH_SEQ_READS;
+ }
+}
+
+static int marvell_nfc_hw_ecc_bch_read_page(struct mtd_info *mtd,
+ struct nand_chip *chip,
+ u8 *buf, int oob_required,
+ int page)
+{
+ const struct marvell_hw_ecc_layout *lt = to_marvell_nand(chip)->layout;
+ int data_len = lt->data_bytes, spare_len = lt->spare_bytes, ecc_len;
+ u8 *data = buf, *spare = chip->oob_poi, *ecc;
+ int max_bitflips = 0;
+ u32 failure_mask = 0;
+ int chunk, ecc_offset_in_page, ret;
+
+ /*
+ * With BCH, OOB is not fully used (and thus not read entirely), not
+ * expected bytes could show up at the end of the OOB buffer if not
+ * explicitly erased.
+ */
+ if (oob_required)
+ memset(chip->oob_poi, 0xFF, mtd->oobsize);
+
+ marvell_nfc_enable_hw_ecc(chip);
+
+ for (chunk = 0; chunk < lt->nchunks; chunk++) {
+ /* Update length for the last chunk */
+ if (chunk >= lt->full_chunk_cnt) {
+ data_len = lt->last_data_bytes;
+ spare_len = lt->last_spare_bytes;
+ }
+
+ /* Read the chunk and detect number of bitflips */
+ marvell_nfc_hw_ecc_bch_read_chunk(chip, chunk, data, data_len,
+ spare, spare_len, page);
+ ret = marvell_nfc_hw_ecc_correct(chip, &max_bitflips);
+ if (ret)
+ failure_mask |= BIT(chunk);
+
+ data += data_len;
+ spare += spare_len;
+ }
+
+ marvell_nfc_disable_hw_ecc(chip);
+
+ if (!failure_mask)
+ return max_bitflips;
+
+ /*
+ * Please note that dumping the ECC bytes during a normal read with OOB
+ * area would add a significant overhead as ECC bytes are "consumed" by
+ * the controller in normal mode and must be re-read in raw mode. To
+ * avoid dropping the performances, we prefer not to include them. The
+ * user should re-read the page in raw mode if ECC bytes are required.
+ *
+ * However, for any subpage read error reported by ->correct(), the ECC
+ * bytes must be read in raw mode and the full subpage must be checked
+ * to see if it is entirely empty of if there was an actual error.
+ */
+ for (chunk = 0; chunk < lt->nchunks; chunk++) {
+ /* No failure reported for this chunk, move to the next one */
+ if (!(failure_mask & BIT(chunk)))
+ continue;
+
+ /* Derive ECC bytes positions (in page/buffer) and length */
+ ecc = chip->oob_poi +
+ (lt->full_chunk_cnt * lt->spare_bytes) +
+ lt->last_spare_bytes +
+ (chunk * ALIGN(lt->ecc_bytes, 32));
+ ecc_offset_in_page =
+ (chunk * (lt->data_bytes + lt->spare_bytes +
+ lt->ecc_bytes)) +
+ (chunk < lt->full_chunk_cnt ?
+ lt->data_bytes + lt->spare_bytes :
+ lt->last_data_bytes + lt->last_spare_bytes);
+ ecc_len = chunk < lt->full_chunk_cnt ?
+ lt->ecc_bytes : lt->last_ecc_bytes;
+
+ /* Do the actual raw read of the ECC bytes */
+ nand_change_read_column_op(chip, ecc_offset_in_page,
+ ecc, ecc_len, false);
+
+ /* Derive data/spare bytes positions (in buffer) and length */
+ data = buf + (chunk * lt->data_bytes);
+ data_len = chunk < lt->full_chunk_cnt ?
+ lt->data_bytes : lt->last_data_bytes;
+ spare = chip->oob_poi + (chunk * (lt->spare_bytes +
+ lt->ecc_bytes));
+ spare_len = chunk < lt->full_chunk_cnt ?
+ lt->spare_bytes : lt->last_spare_bytes;
+
+ /* Check the entire chunk (data + spare + ecc) for emptyness */
+ marvell_nfc_check_empty_chunk(chip, data, data_len, spare,
+ spare_len, ecc, ecc_len,
+ &max_bitflips);
+ }
+
+ return max_bitflips;
+}
+
+static int marvell_nfc_hw_ecc_bch_read_oob_raw(struct mtd_info *mtd,
+ struct nand_chip *chip, int page)
+{
+ /* Invalidate page cache */
+ chip->pagebuf = -1;
+
+ return chip->ecc.read_page_raw(mtd, chip, chip->data_buf, true, page);
+}
+
+static int marvell_nfc_hw_ecc_bch_read_oob(struct mtd_info *mtd,
+ struct nand_chip *chip, int page)
+{
+ /* Invalidate page cache */
+ chip->pagebuf = -1;
+
+ return chip->ecc.read_page(mtd, chip, chip->data_buf, true, page);
+}
+
+/* BCH write helpers */
+static int marvell_nfc_hw_ecc_bch_write_page_raw(struct mtd_info *mtd,
+ struct nand_chip *chip,
+ const u8 *buf,
+ int oob_required, int page)
+{
+ const struct marvell_hw_ecc_layout *lt = to_marvell_nand(chip)->layout;
+ int full_chunk_size = lt->data_bytes + lt->spare_bytes + lt->ecc_bytes;
+ int data_len = lt->data_bytes;
+ int spare_len = lt->spare_bytes;
+ int ecc_len = lt->ecc_bytes;
+ int oob_len = spare_len + ecc_len;
+ int spare_offset = 0;
+ int ecc_offset = (lt->full_chunk_cnt * lt->spare_bytes) +
+ lt->last_spare_bytes;
+ int chunk;
+
+ nand_prog_page_begin_op(chip, page, 0, NULL, 0);
+
+ for (chunk = 0; chunk < lt->nchunks; chunk++) {
+ if (chunk >= lt->full_chunk_cnt) {
+ data_len = lt->last_data_bytes;
+ spare_len = lt->last_spare_bytes;
+ ecc_len = lt->last_ecc_bytes;
+ oob_len = spare_len + ecc_len;
+ }
+
+ /* Point to the column of the next chunk */
+ nand_change_write_column_op(chip, chunk * full_chunk_size,
+ NULL, 0, false);
+
+ /* Write the data */
+ nand_write_data_op(chip, buf + (chunk * lt->data_bytes),
+ data_len, false);
+
+ if (!oob_required)
+ continue;
+
+ /* Write the spare bytes */
+ if (spare_len)
+ nand_write_data_op(chip, chip->oob_poi + spare_offset,
+ spare_len, false);
+
+ /* Write the ECC bytes */
+ if (ecc_len)
+ nand_write_data_op(chip, chip->oob_poi + ecc_offset,
+ ecc_len, false);
+
+ spare_offset += spare_len;
+ ecc_offset += ALIGN(ecc_len, 32);
+ }
+
+ return nand_prog_page_end_op(chip);
+}
+
+static int
+marvell_nfc_hw_ecc_bch_write_chunk(struct nand_chip *chip, int chunk,
+ const u8 *data, unsigned int data_len,
+ const u8 *spare, unsigned int spare_len,
+ int page)
+{
+ struct marvell_nand_chip *marvell_nand = to_marvell_nand(chip);
+ struct marvell_nfc *nfc = to_marvell_nfc(chip->controller);
+ const struct marvell_hw_ecc_layout *lt = to_marvell_nand(chip)->layout;
+ int ret;
+ struct marvell_nfc_op nfc_op = {
+ .ndcb[0] = NDCB0_CMD_TYPE(TYPE_WRITE) | NDCB0_LEN_OVRD,
+ .ndcb[3] = data_len + spare_len,
+ };
+
+ /*
+ * First operation dispatches the CMD_SEQIN command, issue the address
+ * cycles and asks for the first chunk of data.
+ * All operations in the middle (if any) will issue a naked write and
+ * also ask for data.
+ * Last operation (if any) asks for the last chunk of data through a
+ * last naked write.
+ */
+ if (chunk == 0) {
+ nfc_op.ndcb[0] |= NDCB0_CMD_XTYPE(XTYPE_WRITE_DISPATCH) |
+ NDCB0_ADDR_CYC(marvell_nand->addr_cyc) |
+ NDCB0_CMD1(NAND_CMD_SEQIN);
+ nfc_op.ndcb[1] |= NDCB1_ADDRS_PAGE(page);
+ nfc_op.ndcb[2] |= NDCB2_ADDR5_PAGE(page);
+ } else if (chunk < lt->nchunks - 1) {
+ nfc_op.ndcb[0] |= NDCB0_CMD_XTYPE(XTYPE_NAKED_RW);
+ } else {
+ nfc_op.ndcb[0] |= NDCB0_CMD_XTYPE(XTYPE_LAST_NAKED_RW);
+ }
+
+ /* Always dispatch the PAGEPROG command on the last chunk */
+ if (chunk == lt->nchunks - 1)
+ nfc_op.ndcb[0] |= NDCB0_CMD2(NAND_CMD_PAGEPROG) | NDCB0_DBC;
+
+ ret = marvell_nfc_prepare_cmd(chip);
+ if (ret)
+ return ret;
+
+ marvell_nfc_send_cmd(chip, &nfc_op);
+ ret = marvell_nfc_end_cmd(chip, NDSR_WRDREQ,
+ "WRDREQ while loading FIFO (data)");
+ if (ret)
+ return ret;
+
+ /* Transfer the contents */
+ iowrite32_rep(nfc->regs + NDDB, data, FIFO_REP(data_len));
+ iowrite32_rep(nfc->regs + NDDB, spare, FIFO_REP(spare_len));
+
+ return 0;
+}
+
+static int marvell_nfc_hw_ecc_bch_write_page(struct mtd_info *mtd,
+ struct nand_chip *chip,
+ const u8 *buf,
+ int oob_required, int page)
+{
+ const struct marvell_hw_ecc_layout *lt = to_marvell_nand(chip)->layout;
+ const u8 *data = buf;
+ const u8 *spare = chip->oob_poi;
+ int data_len = lt->data_bytes;
+ int spare_len = lt->spare_bytes;
+ int chunk, ret;
+
+ /* Spare data will be written anyway, so clear it to avoid garbage */
+ if (!oob_required)
+ memset(chip->oob_poi, 0xFF, mtd->oobsize);
+
+ marvell_nfc_enable_hw_ecc(chip);
+
+ for (chunk = 0; chunk < lt->nchunks; chunk++) {
+ if (chunk >= lt->full_chunk_cnt) {
+ data_len = lt->last_data_bytes;
+ spare_len = lt->last_spare_bytes;
+ }
+
+ marvell_nfc_hw_ecc_bch_write_chunk(chip, chunk, data, data_len,
+ spare, spare_len, page);
+ data += data_len;
+ spare += spare_len;
+
+ /*
+ * Waiting only for CMDD or PAGED is not enough, ECC are
+ * partially written. No flag is set once the operation is
+ * really finished but the ND_RUN bit is cleared, so wait for it
+ * before stepping into the next command.
+ */
+ marvell_nfc_wait_ndrun(chip);
+ }
+
+ ret = marvell_nfc_wait_op(chip,
+ chip->data_interface.timings.sdr.tPROG_max);
+
+ marvell_nfc_disable_hw_ecc(chip);
+
+ if (ret)
+ return ret;
+
+ return 0;
+}
+
+static int marvell_nfc_hw_ecc_bch_write_oob_raw(struct mtd_info *mtd,
+ struct nand_chip *chip,
+ int page)
+{
+ /* Invalidate page cache */
+ chip->pagebuf = -1;
+
+ memset(chip->data_buf, 0xFF, mtd->writesize);
+
+ return chip->ecc.write_page_raw(mtd, chip, chip->data_buf, true, page);
+}
+
+static int marvell_nfc_hw_ecc_bch_write_oob(struct mtd_info *mtd,
+ struct nand_chip *chip, int page)
+{
+ /* Invalidate page cache */
+ chip->pagebuf = -1;
+
+ memset(chip->data_buf, 0xFF, mtd->writesize);
+
+ return chip->ecc.write_page(mtd, chip, chip->data_buf, true, page);
+}
+
+/* NAND framework ->exec_op() hooks and related helpers */
+static void marvell_nfc_parse_instructions(struct nand_chip *chip,
+ const struct nand_subop *subop,
+ struct marvell_nfc_op *nfc_op)
+{
+ const struct nand_op_instr *instr = NULL;
+ struct marvell_nfc *nfc = to_marvell_nfc(chip->controller);
+ bool first_cmd = true;
+ unsigned int op_id;
+ int i;
+
+ /* Reset the input structure as most of its fields will be OR'ed */
+ memset(nfc_op, 0, sizeof(struct marvell_nfc_op));
+
+ for (op_id = 0; op_id < subop->ninstrs; op_id++) {
+ unsigned int offset, naddrs;
+ const u8 *addrs;
+ int len = nand_subop_get_data_len(subop, op_id);
+
+ instr = &subop->instrs[op_id];
+
+ switch (instr->type) {
+ case NAND_OP_CMD_INSTR:
+ if (first_cmd)
+ nfc_op->ndcb[0] |=
+ NDCB0_CMD1(instr->ctx.cmd.opcode);
+ else
+ nfc_op->ndcb[0] |=
+ NDCB0_CMD2(instr->ctx.cmd.opcode) |
+ NDCB0_DBC;
+
+ nfc_op->cle_ale_delay_ns = instr->delay_ns;
+ first_cmd = false;
+ break;
+
+ case NAND_OP_ADDR_INSTR:
+ offset = nand_subop_get_addr_start_off(subop, op_id);
+ naddrs = nand_subop_get_num_addr_cyc(subop, op_id);
+ addrs = &instr->ctx.addr.addrs[offset];
+
+ nfc_op->ndcb[0] |= NDCB0_ADDR_CYC(naddrs);
+
+ for (i = 0; i < min_t(unsigned int, 4, naddrs); i++)
+ nfc_op->ndcb[1] |= addrs[i] << (8 * i);
+
+ if (naddrs >= 5)
+ nfc_op->ndcb[2] |= NDCB2_ADDR5_CYC(addrs[4]);
+ if (naddrs >= 6)
+ nfc_op->ndcb[3] |= NDCB3_ADDR6_CYC(addrs[5]);
+ if (naddrs == 7)
+ nfc_op->ndcb[3] |= NDCB3_ADDR7_CYC(addrs[6]);
+
+ nfc_op->cle_ale_delay_ns = instr->delay_ns;
+ break;
+
+ case NAND_OP_DATA_IN_INSTR:
+ nfc_op->data_instr = instr;
+ nfc_op->data_instr_idx = op_id;
+ nfc_op->ndcb[0] |= NDCB0_CMD_TYPE(TYPE_READ);
+ if (nfc->caps->is_nfcv2) {
+ nfc_op->ndcb[0] |=
+ NDCB0_CMD_XTYPE(XTYPE_MONOLITHIC_RW) |
+ NDCB0_LEN_OVRD;
+ nfc_op->ndcb[3] |= round_up(len, FIFO_DEPTH);
+ }
+ nfc_op->data_delay_ns = instr->delay_ns;
+ break;
+
+ case NAND_OP_DATA_OUT_INSTR:
+ nfc_op->data_instr = instr;
+ nfc_op->data_instr_idx = op_id;
+ nfc_op->ndcb[0] |= NDCB0_CMD_TYPE(TYPE_WRITE);
+ if (nfc->caps->is_nfcv2) {
+ nfc_op->ndcb[0] |=
+ NDCB0_CMD_XTYPE(XTYPE_MONOLITHIC_RW) |
+ NDCB0_LEN_OVRD;
+ nfc_op->ndcb[3] |= round_up(len, FIFO_DEPTH);
+ }
+ nfc_op->data_delay_ns = instr->delay_ns;
+ break;
+
+ case NAND_OP_WAITRDY_INSTR:
+ nfc_op->rdy_timeout_ms = instr->ctx.waitrdy.timeout_ms;
+ nfc_op->rdy_delay_ns = instr->delay_ns;
+ break;
+ }
+ }
+}
+
+static int marvell_nfc_xfer_data_pio(struct nand_chip *chip,
+ const struct nand_subop *subop,
+ struct marvell_nfc_op *nfc_op)
+{
+ struct marvell_nfc *nfc = to_marvell_nfc(chip->controller);
+ const struct nand_op_instr *instr = nfc_op->data_instr;
+ unsigned int op_id = nfc_op->data_instr_idx;
+ unsigned int len = nand_subop_get_data_len(subop, op_id);
+ unsigned int offset = nand_subop_get_data_start_off(subop, op_id);
+ bool reading = (instr->type == NAND_OP_DATA_IN_INSTR);
+ int ret;
+
+ if (instr->ctx.data.force_8bit)
+ marvell_nfc_force_byte_access(chip, true);
+
+ if (reading) {
+ u8 *in = instr->ctx.data.buf.in + offset;
+
+ ret = marvell_nfc_xfer_data_in_pio(nfc, in, len);
+ } else {
+ const u8 *out = instr->ctx.data.buf.out + offset;
+
+ ret = marvell_nfc_xfer_data_out_pio(nfc, out, len);
+ }
+
+ if (instr->ctx.data.force_8bit)
+ marvell_nfc_force_byte_access(chip, false);
+
+ return ret;
+}
+
+static int marvell_nfc_monolithic_access_exec(struct nand_chip *chip,
+ const struct nand_subop *subop)
+{
+ struct marvell_nfc_op nfc_op;
+ bool reading;
+ int ret;
+
+ marvell_nfc_parse_instructions(chip, subop, &nfc_op);
+ reading = (nfc_op.data_instr->type == NAND_OP_DATA_IN_INSTR);
+
+ ret = marvell_nfc_prepare_cmd(chip);
+ if (ret)
+ return ret;
+
+ marvell_nfc_send_cmd(chip, &nfc_op);
+ ret = marvell_nfc_end_cmd(chip, NDSR_RDDREQ | NDSR_WRDREQ,
+ "RDDREQ/WRDREQ while draining raw data");
+ if (ret)
+ return ret;
+
+ cond_delay(nfc_op.cle_ale_delay_ns);
+
+ if (reading) {
+ if (nfc_op.rdy_timeout_ms) {
+ ret = marvell_nfc_wait_op(chip, nfc_op.rdy_timeout_ms);
+ if (ret)
+ return ret;
+ }
+
+ cond_delay(nfc_op.rdy_delay_ns);
+ }
+
+ marvell_nfc_xfer_data_pio(chip, subop, &nfc_op);
+ ret = marvell_nfc_wait_cmdd(chip);
+ if (ret)
+ return ret;
+
+ cond_delay(nfc_op.data_delay_ns);
+
+ if (!reading) {
+ if (nfc_op.rdy_timeout_ms) {
+ ret = marvell_nfc_wait_op(chip, nfc_op.rdy_timeout_ms);
+ if (ret)
+ return ret;
+ }
+
+ cond_delay(nfc_op.rdy_delay_ns);
+ }
+
+ /*
+ * NDCR ND_RUN bit should be cleared automatically at the end of each
+ * operation but experience shows that the behavior is buggy when it
+ * comes to writes (with LEN_OVRD). Clear it by hand in this case.
+ */
+ if (!reading) {
+ struct marvell_nfc *nfc = to_marvell_nfc(chip->controller);
+
+ writel_relaxed(readl(nfc->regs + NDCR) & ~NDCR_ND_RUN,
+ nfc->regs + NDCR);
+ }
+
+ return 0;
+}
+
+static int marvell_nfc_naked_access_exec(struct nand_chip *chip,
+ const struct nand_subop *subop)
+{
+ struct marvell_nfc_op nfc_op;
+ int ret;
+
+ marvell_nfc_parse_instructions(chip, subop, &nfc_op);
+
+ /*
+ * Naked access are different in that they need to be flagged as naked
+ * by the controller. Reset the controller registers fields that inform
+ * on the type and refill them according to the ongoing operation.
+ */
+ nfc_op.ndcb[0] &= ~(NDCB0_CMD_TYPE(TYPE_MASK) |
+ NDCB0_CMD_XTYPE(XTYPE_MASK));
+ switch (subop->instrs[0].type) {
+ case NAND_OP_CMD_INSTR:
+ nfc_op.ndcb[0] |= NDCB0_CMD_TYPE(TYPE_NAKED_CMD);
+ break;
+ case NAND_OP_ADDR_INSTR:
+ nfc_op.ndcb[0] |= NDCB0_CMD_TYPE(TYPE_NAKED_ADDR);
+ break;
+ case NAND_OP_DATA_IN_INSTR:
+ nfc_op.ndcb[0] |= NDCB0_CMD_TYPE(TYPE_READ) |
+ NDCB0_CMD_XTYPE(XTYPE_LAST_NAKED_RW);
+ break;
+ case NAND_OP_DATA_OUT_INSTR:
+ nfc_op.ndcb[0] |= NDCB0_CMD_TYPE(TYPE_WRITE) |
+ NDCB0_CMD_XTYPE(XTYPE_LAST_NAKED_RW);
+ break;
+ default:
+ /* This should never happen */
+ break;
+ }
+
+ ret = marvell_nfc_prepare_cmd(chip);
+ if (ret)
+ return ret;
+
+ marvell_nfc_send_cmd(chip, &nfc_op);
+
+ if (!nfc_op.data_instr) {
+ ret = marvell_nfc_wait_cmdd(chip);
+ cond_delay(nfc_op.cle_ale_delay_ns);
+ return ret;
+ }
+
+ ret = marvell_nfc_end_cmd(chip, NDSR_RDDREQ | NDSR_WRDREQ,
+ "RDDREQ/WRDREQ while draining raw data");
+ if (ret)
+ return ret;
+
+ marvell_nfc_xfer_data_pio(chip, subop, &nfc_op);
+ ret = marvell_nfc_wait_cmdd(chip);
+ if (ret)
+ return ret;
+
+ /*
+ * NDCR ND_RUN bit should be cleared automatically at the end of each
+ * operation but experience shows that the behavior is buggy when it
+ * comes to writes (with LEN_OVRD). Clear it by hand in this case.
+ */
+ if (subop->instrs[0].type == NAND_OP_DATA_OUT_INSTR) {
+ struct marvell_nfc *nfc = to_marvell_nfc(chip->controller);
+
+ writel_relaxed(readl(nfc->regs + NDCR) & ~NDCR_ND_RUN,
+ nfc->regs + NDCR);
+ }
+
+ return 0;
+}
+
+static int marvell_nfc_naked_waitrdy_exec(struct nand_chip *chip,
+ const struct nand_subop *subop)
+{
+ struct marvell_nfc_op nfc_op;
+ int ret;
+
+ marvell_nfc_parse_instructions(chip, subop, &nfc_op);
+
+ ret = marvell_nfc_wait_op(chip, nfc_op.rdy_timeout_ms);
+ cond_delay(nfc_op.rdy_delay_ns);
+
+ return ret;
+}
+
+static int marvell_nfc_read_id_type_exec(struct nand_chip *chip,
+ const struct nand_subop *subop)
+{
+ struct marvell_nfc_op nfc_op;
+ int ret;
+
+ marvell_nfc_parse_instructions(chip, subop, &nfc_op);
+ nfc_op.ndcb[0] &= ~NDCB0_CMD_TYPE(TYPE_READ);
+ nfc_op.ndcb[0] |= NDCB0_CMD_TYPE(TYPE_READ_ID);
+
+ ret = marvell_nfc_prepare_cmd(chip);
+ if (ret)
+ return ret;
+
+ marvell_nfc_send_cmd(chip, &nfc_op);
+ ret = marvell_nfc_end_cmd(chip, NDSR_RDDREQ,
+ "RDDREQ while reading ID");
+ if (ret)
+ return ret;
+
+ cond_delay(nfc_op.cle_ale_delay_ns);
+
+ if (nfc_op.rdy_timeout_ms) {
+ ret = marvell_nfc_wait_op(chip, nfc_op.rdy_timeout_ms);
+ if (ret)
+ return ret;
+ }
+
+ cond_delay(nfc_op.rdy_delay_ns);
+
+ marvell_nfc_xfer_data_pio(chip, subop, &nfc_op);
+ ret = marvell_nfc_wait_cmdd(chip);
+ if (ret)
+ return ret;
+
+ cond_delay(nfc_op.data_delay_ns);
+
+ return 0;
+}
+
+static int marvell_nfc_read_status_exec(struct nand_chip *chip,
+ const struct nand_subop *subop)
+{
+ struct marvell_nfc_op nfc_op;
+ int ret;
+
+ marvell_nfc_parse_instructions(chip, subop, &nfc_op);
+ nfc_op.ndcb[0] &= ~NDCB0_CMD_TYPE(TYPE_READ);
+ nfc_op.ndcb[0] |= NDCB0_CMD_TYPE(TYPE_STATUS);
+
+ ret = marvell_nfc_prepare_cmd(chip);
+ if (ret)
+ return ret;
+
+ marvell_nfc_send_cmd(chip, &nfc_op);
+ ret = marvell_nfc_end_cmd(chip, NDSR_RDDREQ,
+ "RDDREQ while reading status");
+ if (ret)
+ return ret;
+
+ cond_delay(nfc_op.cle_ale_delay_ns);
+
+ if (nfc_op.rdy_timeout_ms) {
+ ret = marvell_nfc_wait_op(chip, nfc_op.rdy_timeout_ms);
+ if (ret)
+ return ret;
+ }
+
+ cond_delay(nfc_op.rdy_delay_ns);
+
+ marvell_nfc_xfer_data_pio(chip, subop, &nfc_op);
+ ret = marvell_nfc_wait_cmdd(chip);
+ if (ret)
+ return ret;
+
+ cond_delay(nfc_op.data_delay_ns);
+
+ return 0;
+}
+
+static int marvell_nfc_reset_cmd_type_exec(struct nand_chip *chip,
+ const struct nand_subop *subop)
+{
+ struct marvell_nfc_op nfc_op;
+ int ret;
+
+ marvell_nfc_parse_instructions(chip, subop, &nfc_op);
+ nfc_op.ndcb[0] |= NDCB0_CMD_TYPE(TYPE_RESET);
+
+ ret = marvell_nfc_prepare_cmd(chip);
+ if (ret)
+ return ret;
+
+ marvell_nfc_send_cmd(chip, &nfc_op);
+ ret = marvell_nfc_wait_cmdd(chip);
+ if (ret)
+ return ret;
+
+ cond_delay(nfc_op.cle_ale_delay_ns);
+
+ ret = marvell_nfc_wait_op(chip, nfc_op.rdy_timeout_ms);
+ if (ret)
+ return ret;
+
+ cond_delay(nfc_op.rdy_delay_ns);
+
+ return 0;
+}
+
+static int marvell_nfc_erase_cmd_type_exec(struct nand_chip *chip,
+ const struct nand_subop *subop)
+{
+ struct marvell_nfc_op nfc_op;
+ int ret;
+
+ marvell_nfc_parse_instructions(chip, subop, &nfc_op);
+ nfc_op.ndcb[0] |= NDCB0_CMD_TYPE(TYPE_ERASE);
+
+ ret = marvell_nfc_prepare_cmd(chip);
+ if (ret)
+ return ret;
+
+ marvell_nfc_send_cmd(chip, &nfc_op);
+ ret = marvell_nfc_wait_cmdd(chip);
+ if (ret)
+ return ret;
+
+ cond_delay(nfc_op.cle_ale_delay_ns);
+
+ ret = marvell_nfc_wait_op(chip, nfc_op.rdy_timeout_ms);
+ if (ret)
+ return ret;
+
+ cond_delay(nfc_op.rdy_delay_ns);
+
+ return 0;
+}
+
+static const struct nand_op_parser marvell_nfcv2_op_parser = NAND_OP_PARSER(
+ /* Monolithic reads/writes */
+ NAND_OP_PARSER_PATTERN(
+ marvell_nfc_monolithic_access_exec,
+ NAND_OP_PARSER_PAT_CMD_ELEM(false),
+ NAND_OP_PARSER_PAT_ADDR_ELEM(true, MAX_ADDRESS_CYC_NFCV2),
+ NAND_OP_PARSER_PAT_CMD_ELEM(true),
+ NAND_OP_PARSER_PAT_WAITRDY_ELEM(true),
+ NAND_OP_PARSER_PAT_DATA_IN_ELEM(false, MAX_CHUNK_SIZE)),
+ NAND_OP_PARSER_PATTERN(
+ marvell_nfc_monolithic_access_exec,
+ NAND_OP_PARSER_PAT_CMD_ELEM(false),
+ NAND_OP_PARSER_PAT_ADDR_ELEM(false, MAX_ADDRESS_CYC_NFCV2),
+ NAND_OP_PARSER_PAT_DATA_OUT_ELEM(false, MAX_CHUNK_SIZE),
+ NAND_OP_PARSER_PAT_CMD_ELEM(true),
+ NAND_OP_PARSER_PAT_WAITRDY_ELEM(true)),
+ /* Naked commands */
+ NAND_OP_PARSER_PATTERN(
+ marvell_nfc_naked_access_exec,
+ NAND_OP_PARSER_PAT_CMD_ELEM(false)),
+ NAND_OP_PARSER_PATTERN(
+ marvell_nfc_naked_access_exec,
+ NAND_OP_PARSER_PAT_ADDR_ELEM(false, MAX_ADDRESS_CYC_NFCV2)),
+ NAND_OP_PARSER_PATTERN(
+ marvell_nfc_naked_access_exec,
+ NAND_OP_PARSER_PAT_DATA_IN_ELEM(false, MAX_CHUNK_SIZE)),
+ NAND_OP_PARSER_PATTERN(
+ marvell_nfc_naked_access_exec,
+ NAND_OP_PARSER_PAT_DATA_OUT_ELEM(false, MAX_CHUNK_SIZE)),
+ NAND_OP_PARSER_PATTERN(
+ marvell_nfc_naked_waitrdy_exec,
+ NAND_OP_PARSER_PAT_WAITRDY_ELEM(false)),
+ );
+
+static const struct nand_op_parser marvell_nfcv1_op_parser = NAND_OP_PARSER(
+ /* Naked commands not supported, use a function for each pattern */
+ NAND_OP_PARSER_PATTERN(
+ marvell_nfc_read_id_type_exec,
+ NAND_OP_PARSER_PAT_CMD_ELEM(false),
+ NAND_OP_PARSER_PAT_ADDR_ELEM(false, MAX_ADDRESS_CYC_NFCV1),
+ NAND_OP_PARSER_PAT_DATA_IN_ELEM(false, 8)),
+ NAND_OP_PARSER_PATTERN(
+ marvell_nfc_erase_cmd_type_exec,
+ NAND_OP_PARSER_PAT_CMD_ELEM(false),
+ NAND_OP_PARSER_PAT_ADDR_ELEM(false, MAX_ADDRESS_CYC_NFCV1),
+ NAND_OP_PARSER_PAT_CMD_ELEM(false),
+ NAND_OP_PARSER_PAT_WAITRDY_ELEM(false)),
+ NAND_OP_PARSER_PATTERN(
+ marvell_nfc_read_status_exec,
+ NAND_OP_PARSER_PAT_CMD_ELEM(false),
+ NAND_OP_PARSER_PAT_DATA_IN_ELEM(false, 1)),
+ NAND_OP_PARSER_PATTERN(
+ marvell_nfc_reset_cmd_type_exec,
+ NAND_OP_PARSER_PAT_CMD_ELEM(false),
+ NAND_OP_PARSER_PAT_WAITRDY_ELEM(false)),
+ NAND_OP_PARSER_PATTERN(
+ marvell_nfc_naked_waitrdy_exec,
+ NAND_OP_PARSER_PAT_WAITRDY_ELEM(false)),
+ );
+
+static int marvell_nfc_exec_op(struct nand_chip *chip,
+ const struct nand_operation *op,
+ bool check_only)
+{
+ struct marvell_nfc *nfc = to_marvell_nfc(chip->controller);
+
+ if (nfc->caps->is_nfcv2)
+ return nand_op_parser_exec_op(chip, &marvell_nfcv2_op_parser,
+ op, check_only);
+ else
+ return nand_op_parser_exec_op(chip, &marvell_nfcv1_op_parser,
+ op, check_only);
+}
+
+/*
+ * Layouts were broken in old pxa3xx_nand driver, these are supposed to be
+ * usable.
+ */
+static int marvell_nand_ooblayout_ecc(struct mtd_info *mtd, int section,
+ struct mtd_oob_region *oobregion)
+{
+ struct nand_chip *chip = mtd_to_nand(mtd);
+ const struct marvell_hw_ecc_layout *lt = to_marvell_nand(chip)->layout;
+
+ if (section >= lt->nchunks)
+ return -ERANGE;
+
+ oobregion->offset = (lt->full_chunk_cnt * lt->spare_bytes) +
+ section * lt->ecc_bytes;
+ oobregion->length = section < lt->full_chunk_cnt ?
+ lt->ecc_bytes : lt->last_ecc_bytes;
+
+ return 0;
+}
+
+static int marvell_nand_ooblayout_free(struct mtd_info *mtd, int section,
+ struct mtd_oob_region *oobregion)
+{
+ struct nand_chip *chip = mtd_to_nand(mtd);
+ const struct marvell_hw_ecc_layout *lt = to_marvell_nand(chip)->layout;
+
+ if (section >= lt->nchunks)
+ return -ERANGE;
+
+ oobregion->offset = section * lt->spare_bytes;
+ oobregion->length = section < lt->full_chunk_cnt ?
+ lt->spare_bytes : lt->last_spare_bytes;
+
+ if (!section) {
+ /*
+ * Bootrom looks in bytes 0 & 5 for bad blocks for the
+ * 4KB page / 4bit BCH combination.
+ */
+ if (mtd->writesize == SZ_4K && lt->data_bytes == SZ_2K) {
+ oobregion->offset += 6;
+ oobregion->length -= 6;
+ } else {
+ oobregion->offset += 2;
+ oobregion->length -= 2;
+ }
+ }
+
+ return 0;
+}
+
+static const struct mtd_ooblayout_ops marvell_nand_ooblayout_ops = {
+ .ecc = marvell_nand_ooblayout_ecc,
+ .free = marvell_nand_ooblayout_free,
+};
+
+static int marvell_nand_hw_ecc_ctrl_init(struct mtd_info *mtd,
+ struct nand_ecc_ctrl *ecc)
+{
+ struct nand_chip *chip = mtd_to_nand(mtd);
+ struct marvell_nfc *nfc = to_marvell_nfc(chip->controller);
+ const struct marvell_hw_ecc_layout *l;
+ int i;
+
+ if (!nfc->caps->is_nfcv2 &&
+ (mtd->writesize + mtd->oobsize > MAX_CHUNK_SIZE)) {
+ dev_err(nfc->dev,
+ "NFCv1: writesize (%d) cannot be bigger than a chunk (%d)\n",
+ mtd->writesize, MAX_CHUNK_SIZE - mtd->oobsize);
+ return -ENOTSUPP;
+ }
+
+ to_marvell_nand(chip)->layout = NULL;
+ for (i = 0; i < ARRAY_SIZE(marvell_nfc_layouts); i++) {
+ l = &marvell_nfc_layouts[i];
+ if (mtd->writesize == l->writesize &&
+ ecc->size == l->chunk && ecc->strength == l->strength) {
+ to_marvell_nand(chip)->layout = l;
+ break;
+ }
+ }
+
+ if (!to_marvell_nand(chip)->layout ||
+ (!nfc->caps->is_nfcv2 && ecc->strength > 1)) {
+ dev_err(nfc->dev,
+ "ECC strength %d at page size %d is not supported\n",
+ ecc->strength, mtd->writesize);
+ return -ENOTSUPP;
+ }
+
+ mtd_set_ooblayout(mtd, &marvell_nand_ooblayout_ops);
+ ecc->steps = l->nchunks;
+ ecc->size = l->data_bytes;
+
+ if (ecc->strength == 1) {
+ chip->ecc.algo = NAND_ECC_HAMMING;
+ ecc->read_page_raw = marvell_nfc_hw_ecc_hmg_read_page_raw;
+ ecc->read_page = marvell_nfc_hw_ecc_hmg_read_page;
+ ecc->read_oob_raw = marvell_nfc_hw_ecc_hmg_read_oob_raw;
+ ecc->read_oob = ecc->read_oob_raw;
+ ecc->write_page_raw = marvell_nfc_hw_ecc_hmg_write_page_raw;
+ ecc->write_page = marvell_nfc_hw_ecc_hmg_write_page;
+ ecc->write_oob_raw = marvell_nfc_hw_ecc_hmg_write_oob_raw;
+ ecc->write_oob = ecc->write_oob_raw;
+ } else {
+ chip->ecc.algo = NAND_ECC_BCH;
+ ecc->strength = 16;
+ ecc->read_page_raw = marvell_nfc_hw_ecc_bch_read_page_raw;
+ ecc->read_page = marvell_nfc_hw_ecc_bch_read_page;
+ ecc->read_oob_raw = marvell_nfc_hw_ecc_bch_read_oob_raw;
+ ecc->read_oob = marvell_nfc_hw_ecc_bch_read_oob;
+ ecc->write_page_raw = marvell_nfc_hw_ecc_bch_write_page_raw;
+ ecc->write_page = marvell_nfc_hw_ecc_bch_write_page;
+ ecc->write_oob_raw = marvell_nfc_hw_ecc_bch_write_oob_raw;
+ ecc->write_oob = marvell_nfc_hw_ecc_bch_write_oob;
+ }
+
+ return 0;
+}
+
+static int marvell_nand_ecc_init(struct mtd_info *mtd,
+ struct nand_ecc_ctrl *ecc)
+{
+ struct nand_chip *chip = mtd_to_nand(mtd);
+ struct marvell_nfc *nfc = to_marvell_nfc(chip->controller);
+ int ret;
+
+ if (ecc->mode != NAND_ECC_NONE && (!ecc->size || !ecc->strength)) {
+ if (chip->ecc_step_ds && chip->ecc_strength_ds) {
+ ecc->size = chip->ecc_step_ds;
+ ecc->strength = chip->ecc_strength_ds;
+ } else {
+ dev_info(nfc->dev,
+ "No minimum ECC strength, using 1b/512B\n");
+ ecc->size = 512;
+ ecc->strength = 1;
+ }
+ }
+
+ switch (ecc->mode) {
+ case NAND_ECC_HW:
+ ret = marvell_nand_hw_ecc_ctrl_init(mtd, ecc);
+ if (ret)
+ return ret;
+ break;
+ case NAND_ECC_NONE:
+ case NAND_ECC_SOFT:
+ if (!nfc->caps->is_nfcv2 && mtd->writesize != SZ_512 &&
+ mtd->writesize != SZ_2K) {
+ dev_err(nfc->dev, "NFCv1 cannot write %d bytes pages\n",
+ mtd->writesize);
+ return -EINVAL;
+ }
+ break;
+ default:
+ return -EINVAL;
+ }
+
+ return 0;
+}
+
+static u8 bbt_pattern[] = {'M', 'V', 'B', 'b', 't', '0' };
+static u8 bbt_mirror_pattern[] = {'1', 't', 'b', 'B', 'V', 'M' };
+
+static struct nand_bbt_descr bbt_main_descr = {
+ .options = NAND_BBT_LASTBLOCK | NAND_BBT_CREATE | NAND_BBT_WRITE |
+ NAND_BBT_2BIT | NAND_BBT_VERSION,
+ .offs = 8,
+ .len = 6,
+ .veroffs = 14,
+ .maxblocks = 8, /* Last 8 blocks in each chip */
+ .pattern = bbt_pattern
+};
+
+static struct nand_bbt_descr bbt_mirror_descr = {
+ .options = NAND_BBT_LASTBLOCK | NAND_BBT_CREATE | NAND_BBT_WRITE |
+ NAND_BBT_2BIT | NAND_BBT_VERSION,
+ .offs = 8,
+ .len = 6,
+ .veroffs = 14,
+ .maxblocks = 8, /* Last 8 blocks in each chip */
+ .pattern = bbt_mirror_pattern
+};
+
+static int marvell_nfc_setup_data_interface(struct mtd_info *mtd, int chipnr,
+ const struct nand_data_interface
+ *conf)
+{
+ struct nand_chip *chip = mtd_to_nand(mtd);
+ struct marvell_nand_chip *marvell_nand = to_marvell_nand(chip);
+ struct marvell_nfc *nfc = to_marvell_nfc(chip->controller);
+ unsigned int period_ns = 1000000000 / clk_get_rate(nfc->ecc_clk) * 2;
+ const struct nand_sdr_timings *sdr;
+ struct marvell_nfc_timings nfc_tmg;
+ int read_delay;
+
+ sdr = nand_get_sdr_timings(conf);
+ if (IS_ERR(sdr))
+ return PTR_ERR(sdr);
+
+ /*
+ * SDR timings are given in pico-seconds while NFC timings must be
+ * expressed in NAND controller clock cycles, which is half of the
+ * frequency of the accessible ECC clock retrieved by clk_get_rate().
+ * This is not written anywhere in the datasheet but was observed
+ * with an oscilloscope.
+ *
+ * NFC datasheet gives equations from which thoses calculations
+ * are derived, they tend to be slightly more restrictives than the
+ * given core timings and may improve the overall speed.
+ */
+ nfc_tmg.tRP = TO_CYCLES(DIV_ROUND_UP(sdr->tRC_min, 2), period_ns) - 1;
+ nfc_tmg.tRH = nfc_tmg.tRP;
+ nfc_tmg.tWP = TO_CYCLES(DIV_ROUND_UP(sdr->tWC_min, 2), period_ns) - 1;
+ nfc_tmg.tWH = nfc_tmg.tWP;
+ nfc_tmg.tCS = TO_CYCLES(sdr->tCS_min, period_ns);
+ nfc_tmg.tCH = TO_CYCLES(sdr->tCH_min, period_ns) - 1;
+ nfc_tmg.tADL = TO_CYCLES(sdr->tADL_min, period_ns);
+ /*
+ * Read delay is the time of propagation from SoC pins to NFC internal
+ * logic. With non-EDO timings, this is MIN_RD_DEL_CNT clock cycles. In
+ * EDO mode, an additional delay of tRH must be taken into account so
+ * the data is sampled on the falling edge instead of the rising edge.
+ */
+ read_delay = sdr->tRC_min >= 30000 ?
+ MIN_RD_DEL_CNT : MIN_RD_DEL_CNT + nfc_tmg.tRH;
+
+ nfc_tmg.tAR = TO_CYCLES(sdr->tAR_min, period_ns);
+ /*
+ * tWHR and tRHW are supposed to be read to write delays (and vice
+ * versa) but in some cases, ie. when doing a change column, they must
+ * be greater than that to be sure tCCS delay is respected.
+ */
+ nfc_tmg.tWHR = TO_CYCLES(max_t(int, sdr->tWHR_min, sdr->tCCS_min),
+ period_ns) - 2,
+ nfc_tmg.tRHW = TO_CYCLES(max_t(int, sdr->tRHW_min, sdr->tCCS_min),
+ period_ns);
+
+ /* Use WAIT_MODE (wait for RB line) instead of only relying on delays */
+ nfc_tmg.tR = TO_CYCLES(sdr->tWB_max, period_ns);
+
+ if (chipnr < 0)
+ return 0;
+
+ marvell_nand->ndtr0 =
+ NDTR0_TRP(nfc_tmg.tRP) |
+ NDTR0_TRH(nfc_tmg.tRH) |
+ NDTR0_ETRP(nfc_tmg.tRP) |
+ NDTR0_TWP(nfc_tmg.tWP) |
+ NDTR0_TWH(nfc_tmg.tWH) |
+ NDTR0_TCS(nfc_tmg.tCS) |
+ NDTR0_TCH(nfc_tmg.tCH) |
+ NDTR0_RD_CNT_DEL(read_delay) |
+ NDTR0_SELCNTR |
+ NDTR0_TADL(nfc_tmg.tADL);
+
+ marvell_nand->ndtr1 =
+ NDTR1_TAR(nfc_tmg.tAR) |
+ NDTR1_TWHR(nfc_tmg.tWHR) |
+ NDTR1_TRHW(nfc_tmg.tRHW) |
+ NDTR1_WAIT_MODE |
+ NDTR1_TR(nfc_tmg.tR);
+
+ writel_relaxed(marvell_nand->ndtr0, nfc->regs + NDTR0);
+ writel_relaxed(marvell_nand->ndtr1, nfc->regs + NDTR1);
+
+ return 0;
+}
+
+static int marvell_nand_chip_init(struct device *dev, struct marvell_nfc *nfc,
+ struct device_node *np)
+{
+ struct pxa3xx_nand_platform_data *pdata = dev_get_platdata(dev);
+ struct marvell_nand_chip *marvell_nand;
+ struct mtd_info *mtd;
+ struct nand_chip *chip;
+ int nsels, ret, i;
+ u32 cs, rb;
+
+ /*
+ * The legacy "num-cs" property indicates the number of CS on the only
+ * chip connected to the controller (legacy bindings does not support
+ * more than one chip). CS are only incremented one by one while the RB
+ * pin is always the #0.
+ *
+ * When not using legacy bindings, a couple of "reg" and "nand-rb"
+ * properties must be filled. For each chip, expressed as a subnode,
+ * "reg" points to the CS lines and "nand-rb" to the RB line.
+ */
+ if (pdata) {
+ nsels = 1;
+ } else if (nfc->caps->legacy_of_bindings) {
+ if (!of_get_property(np, "num-cs", &nsels)) {
+ dev_err(dev, "missing num-cs property\n");
+ return -EINVAL;
+ }
+ } else {
+ if (!of_get_property(np, "reg", &nsels)) {
+ dev_err(dev, "missing reg property\n");
+ return -EINVAL;
+ }
+ }
+
+ if (!pdata)
+ nsels /= sizeof(u32);
+ if (!nsels) {
+ dev_err(dev, "invalid reg property size\n");
+ return -EINVAL;
+ }
+
+ /* Alloc the nand chip structure */
+ marvell_nand = devm_kzalloc(dev, sizeof(*marvell_nand) +
+ (nsels *
+ sizeof(struct marvell_nand_chip_sel)),
+ GFP_KERNEL);
+ if (!marvell_nand) {
+ dev_err(dev, "could not allocate chip structure\n");
+ return -ENOMEM;
+ }
+
+ marvell_nand->nsels = nsels;
+ marvell_nand->selected_die = -1;
+
+ for (i = 0; i < nsels; i++) {
+ if (pdata || nfc->caps->legacy_of_bindings) {
+ /*
+ * Legacy bindings use the CS lines in natural
+ * order (0, 1, ...)
+ */
+ cs = i;
+ } else {
+ /* Retrieve CS id */
+ ret = of_property_read_u32_index(np, "reg", i, &cs);
+ if (ret) {
+ dev_err(dev, "could not retrieve reg property: %d\n",
+ ret);
+ return ret;
+ }
+ }
+
+ if (cs >= nfc->caps->max_cs_nb) {
+ dev_err(dev, "invalid reg value: %u (max CS = %d)\n",
+ cs, nfc->caps->max_cs_nb);
+ return -EINVAL;
+ }
+
+ if (test_and_set_bit(cs, &nfc->assigned_cs)) {
+ dev_err(dev, "CS %d already assigned\n", cs);
+ return -EINVAL;
+ }
+
+ /*
+ * The cs variable represents the chip select id, which must be
+ * converted in bit fields for NDCB0 and NDCB2 to select the
+ * right chip. Unfortunately, due to a lack of information on
+ * the subject and incoherent documentation, the user should not
+ * use CS1 and CS3 at all as asserting them is not supported in
+ * a reliable way (due to multiplexing inside ADDR5 field).
+ */
+ marvell_nand->sels[i].cs = cs;
+ switch (cs) {
+ case 0:
+ case 2:
+ marvell_nand->sels[i].ndcb0_csel = 0;
+ break;
+ case 1:
+ case 3:
+ marvell_nand->sels[i].ndcb0_csel = NDCB0_CSEL;
+ break;
+ default:
+ return -EINVAL;
+ }
+
+ /* Retrieve RB id */
+ if (pdata || nfc->caps->legacy_of_bindings) {
+ /* Legacy bindings always use RB #0 */
+ rb = 0;
+ } else {
+ ret = of_property_read_u32_index(np, "nand-rb", i,
+ &rb);
+ if (ret) {
+ dev_err(dev,
+ "could not retrieve RB property: %d\n",
+ ret);
+ return ret;
+ }
+ }
+
+ if (rb >= nfc->caps->max_rb_nb) {
+ dev_err(dev, "invalid reg value: %u (max RB = %d)\n",
+ rb, nfc->caps->max_rb_nb);
+ return -EINVAL;
+ }
+
+ marvell_nand->sels[i].rb = rb;
+ }
+
+ chip = &marvell_nand->chip;
+ chip->controller = &nfc->controller;
+ nand_set_flash_node(chip, np);
+
+ chip->exec_op = marvell_nfc_exec_op;
+ chip->select_chip = marvell_nfc_select_chip;
+ if (nfc->caps->is_nfcv2 &&
+ !of_property_read_bool(np, "marvell,nand-keep-config"))
+ chip->setup_data_interface = marvell_nfc_setup_data_interface;
+
+ mtd = nand_to_mtd(chip);
+ mtd->dev.parent = dev;
+
+ /*
+ * Default to HW ECC engine mode. If the nand-ecc-mode property is given
+ * in the DT node, this entry will be overwritten in nand_scan_ident().
+ */
+ chip->ecc.mode = NAND_ECC_HW;
+
+ chip->options |= NAND_BUSWIDTH_AUTO;
+ ret = nand_scan_ident(mtd, marvell_nand->nsels, NULL);
+ if (ret) {
+ dev_err(dev, "could not identify the nand chip\n");
+ return ret;
+ }
+
+ if (pdata && pdata->flash_bbt)
+ chip->bbt_options |= NAND_BBT_USE_FLASH;
+
+ if (chip->bbt_options & NAND_BBT_USE_FLASH) {
+ /*
+ * We'll use a bad block table stored in-flash and don't
+ * allow writing the bad block marker to the flash.
+ */
+ chip->bbt_options |= NAND_BBT_NO_OOB_BBM;
+ chip->bbt_td = &bbt_main_descr;
+ chip->bbt_md = &bbt_mirror_descr;
+ }
+
+ /*
+ * With RA_START bit set in NDCR, columns takes two address cycles. This
+ * means addressing a chip with more than 256 pages needs a fifth
+ * address cycle. Addressing a chip using CS 2 or 3 should also needs
+ * this additional cycle but due to inconsistance in the documentation
+ * and lack of hardware to test this situation, this case has been
+ * dropped and is not supported by this driver.
+ */
+ marvell_nand->addr_cyc = 4;
+ if (chip->options & NAND_ROW_ADDR_3)
+ marvell_nand->addr_cyc = 5;
+
+ if (pdata) {
+ chip->ecc.size = pdata->ecc_step_size;
+ chip->ecc.strength = pdata->ecc_strength;
+ }
+
+ ret = marvell_nand_ecc_init(mtd, &chip->ecc);
+ if (ret) {
+ dev_err(dev, "ECC init failed: %d\n", ret);
+ return ret;
+ }
+
+ if (chip->ecc.mode == NAND_ECC_HW) {
+ /*
+ * Subpage write not available with hardware ECC, prohibit also
+ * subpage read as in userspace subpage access would still be
+ * allowed and subpage write, if used, would lead to numerous
+ * uncorrectable ECC errors.
+ */
+ chip->options |= NAND_NO_SUBPAGE_WRITE;
+ }
+
+ if (pdata || nfc->caps->legacy_of_bindings) {
+ /*
+ * We keep the MTD name unchanged to avoid breaking platforms
+ * where the MTD cmdline parser is used and the bootloader
+ * has not been updated to use the new naming scheme.
+ */
+ mtd->name = "pxa3xx_nand-0";
+ } else if (!mtd->name) {
+ /*
+ * If the new bindings are used and the bootloader has not been
+ * updated to pass a new mtdparts parameter on the cmdline, you
+ * should define the following property in your NAND node, ie:
+ *
+ * label = "main-storage";
+ *
+ * This way, mtd->name will be set by the core when
+ * nand_set_flash_node() is called.
+ */
+ mtd->name = devm_kasprintf(nfc->dev, GFP_KERNEL,
+ "%s:nand.%d", dev_name(nfc->dev),
+ marvell_nand->sels[0].cs);
+ if (!mtd->name) {
+ dev_err(nfc->dev, "Failed to allocate mtd->name\n");
+ return -ENOMEM;
+ }
+ }
+
+ /*
+ * Save a reference value of NDCR for each NAND chip switch, adapt page
+ * size and bus width.
+ */
+ marvell_nand->ndcr = readl_relaxed(nfc->regs + NDCR);
+ marvell_nand->ndcr &= ~(NDCR_ND_RUN | NDCR_DWIDTH_M | NDCR_DWIDTH_C |
+ NDCR_PAGE_SZ(2048));
+ marvell_nand->ndcr |= NDCR_PAGE_SZ(mtd->writesize);
+ if (chip->options & NAND_BUSWIDTH_16)
+ marvell_nand->ndcr |= NDCR_DWIDTH_M | NDCR_DWIDTH_C;
+
+ ret = nand_scan_tail(mtd);
+ if (ret) {
+ dev_err(dev, "nand_scan_tail failed: %d\n", ret);
+ return ret;
+ }
+
+ if (pdata)
+ /* Legacy bindings support only one chip */
+ ret = mtd_device_register(mtd, pdata->parts[0],
+ pdata->nr_parts[0]);
+ else
+ ret = mtd_device_register(mtd, NULL, 0);
+ if (ret) {
+ dev_err(dev, "failed to register mtd device: %d\n", ret);
+ nand_release(mtd);
+ return ret;
+ }
+
+ list_add_tail(&marvell_nand->node, &nfc->chips);
+
+ return 0;
+}
+
+static int marvell_nand_chips_init(struct device *dev, struct marvell_nfc *nfc)
+{
+ struct device_node *np = dev->of_node;
+ struct device_node *nand_np;
+ int max_cs = nfc->caps->max_cs_nb;
+ int nchips;
+ int ret;
+
+ if (!np)
+ nchips = 1;
+ else
+ nchips = of_get_child_count(np);
+
+ if (nchips > max_cs) {
+ dev_err(dev, "too many NAND chips: %d (max = %d CS)\n", nchips,
+ max_cs);
+ return -EINVAL;
+ }
+
+ /*
+ * Legacy bindings do not use child nodes to exhibit NAND chip
+ * properties and layout. Instead, NAND properties are mixed with the
+ * controller ones, and partitions are defined as direct subnodes of the
+ * NAND controller node.
+ */
+ if (nfc->caps->legacy_of_bindings) {
+ ret = marvell_nand_chip_init(dev, nfc, np);
+ return ret;
+ }
+
+ for_each_child_of_node(np, nand_np) {
+ ret = marvell_nand_chip_init(dev, nfc, nand_np);
+ if (ret) {
+ of_node_put(nand_np);
+ return ret;
+ }
+ }
+
+ return 0;
+}
+
+static void marvell_nand_chips_cleanup(struct marvell_nfc *nfc)
+{
+ struct marvell_nand_chip *entry, *temp;
+
+ list_for_each_entry_safe(entry, temp, &nfc->chips, node) {
+ nand_release(nand_to_mtd(&entry->chip));
+ list_del(&entry->node);
+ }
+}
+
+static int marvell_nfc_init_dma(struct marvell_nfc *nfc)
+{
+ struct platform_device *pdev = container_of(nfc->dev,
+ struct platform_device,
+ dev);
+ struct dma_slave_config config = {};
+ struct resource *r;
+ dma_cap_mask_t mask;
+ struct pxad_param param;
+ int ret;
+
+ if (!IS_ENABLED(CONFIG_PXA_DMA)) {
+ dev_warn(nfc->dev,
+ "DMA not enabled in configuration\n");
+ return -ENOTSUPP;
+ }
+
+ ret = dma_set_mask_and_coherent(nfc->dev, DMA_BIT_MASK(32));
+ if (ret)
+ return ret;
+
+ r = platform_get_resource(pdev, IORESOURCE_DMA, 0);
+ if (!r) {
+ dev_err(nfc->dev, "No resource defined for data DMA\n");
+ return -ENXIO;
+ }
+
+ param.drcmr = r->start;
+ param.prio = PXAD_PRIO_LOWEST;
+ dma_cap_zero(mask);
+ dma_cap_set(DMA_SLAVE, mask);
+ nfc->dma_chan =
+ dma_request_slave_channel_compat(mask, pxad_filter_fn,
+ ¶m, nfc->dev,
+ "data");
+ if (!nfc->dma_chan) {
+ dev_err(nfc->dev,
+ "Unable to request data DMA channel\n");
+ return -ENODEV;
+ }
+
+ r = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+ if (!r)
+ return -ENXIO;
+
+ config.src_addr_width = DMA_SLAVE_BUSWIDTH_4_BYTES;
+ config.dst_addr_width = DMA_SLAVE_BUSWIDTH_4_BYTES;
+ config.src_addr = r->start + NDDB;
+ config.dst_addr = r->start + NDDB;
+ config.src_maxburst = 32;
+ config.dst_maxburst = 32;
+ ret = dmaengine_slave_config(nfc->dma_chan, &config);
+ if (ret < 0) {
+ dev_err(nfc->dev, "Failed to configure DMA channel\n");
+ return ret;
+ }
+
+ /*
+ * DMA must act on length multiple of 32 and this length may be
+ * bigger than the destination buffer. Use this buffer instead
+ * for DMA transfers and then copy the desired amount of data to
+ * the provided buffer.
+ */
+ nfc->dma_buf = kmalloc(MAX_CHUNK_SIZE, GFP_DMA);
+ if (!nfc->dma_buf)
+ return -ENOMEM;
+
+ nfc->use_dma = true;
+
+ return 0;
+}
+
+static int marvell_nfc_init(struct marvell_nfc *nfc)
+{
+ struct device_node *np = nfc->dev->of_node;
+
+ /*
+ * Some SoCs like A7k/A8k need to enable manually the NAND
+ * controller, gated clocks and reset bits to avoid being bootloader
+ * dependent. This is done through the use of the System Functions
+ * registers.
+ */
+ if (nfc->caps->need_system_controller) {
+ struct regmap *sysctrl_base =
+ syscon_regmap_lookup_by_phandle(np,
+ "marvell,system-controller");
+ u32 reg;
+
+ if (IS_ERR(sysctrl_base))
+ return PTR_ERR(sysctrl_base);
+
+ reg = GENCONF_SOC_DEVICE_MUX_NFC_EN |
+ GENCONF_SOC_DEVICE_MUX_ECC_CLK_RST |
+ GENCONF_SOC_DEVICE_MUX_ECC_CORE_RST |
+ GENCONF_SOC_DEVICE_MUX_NFC_INT_EN;
+ regmap_write(sysctrl_base, GENCONF_SOC_DEVICE_MUX, reg);
+
+ regmap_read(sysctrl_base, GENCONF_CLK_GATING_CTRL, ®);
+ reg |= GENCONF_CLK_GATING_CTRL_ND_GATE;
+ regmap_write(sysctrl_base, GENCONF_CLK_GATING_CTRL, reg);
+
+ regmap_read(sysctrl_base, GENCONF_ND_CLK_CTRL, ®);
+ reg |= GENCONF_ND_CLK_CTRL_EN;
+ regmap_write(sysctrl_base, GENCONF_ND_CLK_CTRL, reg);
+ }
+
+ /* Configure the DMA if appropriate */
+ if (!nfc->caps->is_nfcv2)
+ marvell_nfc_init_dma(nfc);
+
+ /*
+ * ECC operations and interruptions are only enabled when specifically
+ * needed. ECC shall not be activated in the early stages (fails probe).
+ * Arbiter flag, even if marked as "reserved", must be set (empirical).
+ * SPARE_EN bit must always be set or ECC bytes will not be at the same
+ * offset in the read page and this will fail the protection.
+ */
+ writel_relaxed(NDCR_RA_START | NDCR_ALL_INT | NDCR_ND_ARB_EN |
+ NDCR_SPARE_EN | (nfc->caps->is_nfcv2 ?
+ 0 : NDCR_RD_ID_CNT(NFCV1_READID_LEN)),
+ nfc->regs + NDCR);
+ writel_relaxed(0xFFFFFFFF, nfc->regs + NDSR);
+ writel_relaxed(0, nfc->regs + NDECCCTRL);
+
+ return 0;
+}
+
+static int marvell_nfc_probe(struct platform_device *pdev)
+{
+ struct device *dev = &pdev->dev;
+ struct resource *r;
+ struct marvell_nfc *nfc;
+ int ret;
+ int irq;
+
+ nfc = devm_kzalloc(&pdev->dev, sizeof(struct marvell_nfc),
+ GFP_KERNEL);
+ if (!nfc)
+ return -ENOMEM;
+
+ nfc->dev = dev;
+ nand_hw_control_init(&nfc->controller);
+ INIT_LIST_HEAD(&nfc->chips);
+
+ r = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+ nfc->regs = devm_ioremap_resource(dev, r);
+ if (IS_ERR(nfc->regs))
+ return PTR_ERR(nfc->regs);
+
+ irq = platform_get_irq(pdev, 0);
+ if (irq < 0) {
+ dev_err(dev, "failed to retrieve irq\n");
+ return irq;
+ }
+
+ nfc->ecc_clk = devm_clk_get(&pdev->dev, NULL);
+ if (IS_ERR(nfc->ecc_clk))
+ return PTR_ERR(nfc->ecc_clk);
+
+ ret = clk_prepare_enable(nfc->ecc_clk);
+ if (ret)
+ return ret;
+
+ marvell_nfc_disable_int(nfc, NDCR_ALL_INT);
+ marvell_nfc_clear_int(nfc, NDCR_ALL_INT);
+ ret = devm_request_irq(dev, irq, marvell_nfc_isr,
+ 0, "marvell-nfc", nfc);
+ if (ret)
+ goto unprepare_clk;
+
+ /* Get NAND controller capabilities */
+ if (pdev->id_entry)
+ nfc->caps = (void *)pdev->id_entry->driver_data;
+ else
+ nfc->caps = of_device_get_match_data(&pdev->dev);
+
+ if (!nfc->caps) {
+ dev_err(dev, "Could not retrieve NFC caps\n");
+ ret = -EINVAL;
+ goto unprepare_clk;
+ }
+
+ /* Init the controller and then probe the chips */
+ ret = marvell_nfc_init(nfc);
+ if (ret)
+ goto unprepare_clk;
+
+ platform_set_drvdata(pdev, nfc);
+
+ ret = marvell_nand_chips_init(dev, nfc);
+ if (ret)
+ goto unprepare_clk;
+
+ return 0;
+
+unprepare_clk:
+ clk_disable_unprepare(nfc->ecc_clk);
+
+ return ret;
+}
+
+static int marvell_nfc_remove(struct platform_device *pdev)
+{
+ struct marvell_nfc *nfc = platform_get_drvdata(pdev);
+
+ marvell_nand_chips_cleanup(nfc);
+
+ if (nfc->use_dma) {
+ dmaengine_terminate_all(nfc->dma_chan);
+ dma_release_channel(nfc->dma_chan);
+ }
+
+ clk_disable_unprepare(nfc->ecc_clk);
+
+ return 0;
+}
+
+static const struct marvell_nfc_caps marvell_armada_8k_nfc_caps = {
+ .max_cs_nb = 4,
+ .max_rb_nb = 2,
+ .need_system_controller = true,
+ .is_nfcv2 = true,
+};
+
+static const struct marvell_nfc_caps marvell_armada370_nfc_caps = {
+ .max_cs_nb = 4,
+ .max_rb_nb = 2,
+ .is_nfcv2 = true,
+};
+
+static const struct marvell_nfc_caps marvell_pxa3xx_nfc_caps = {
+ .max_cs_nb = 2,
+ .max_rb_nb = 1,
+ .use_dma = true,
+};
+
+static const struct marvell_nfc_caps marvell_armada_8k_nfc_legacy_caps = {
+ .max_cs_nb = 4,
+ .max_rb_nb = 2,
+ .need_system_controller = true,
+ .legacy_of_bindings = true,
+ .is_nfcv2 = true,
+};
+
+static const struct marvell_nfc_caps marvell_armada370_nfc_legacy_caps = {
+ .max_cs_nb = 4,
+ .max_rb_nb = 2,
+ .legacy_of_bindings = true,
+ .is_nfcv2 = true,
+};
+
+static const struct marvell_nfc_caps marvell_pxa3xx_nfc_legacy_caps = {
+ .max_cs_nb = 2,
+ .max_rb_nb = 1,
+ .legacy_of_bindings = true,
+ .use_dma = true,
+};
+
+static const struct platform_device_id marvell_nfc_platform_ids[] = {
+ {
+ .name = "pxa3xx-nand",
+ .driver_data = (kernel_ulong_t)&marvell_pxa3xx_nfc_legacy_caps,
+ },
+ { /* sentinel */ },
+};
+MODULE_DEVICE_TABLE(platform, marvell_nfc_platform_ids);
+
+static const struct of_device_id marvell_nfc_of_ids[] = {
+ {
+ .compatible = "marvell,armada-8k-nand-controller",
+ .data = &marvell_armada_8k_nfc_caps,
+ },
+ {
+ .compatible = "marvell,armada370-nand-controller",
+ .data = &marvell_armada370_nfc_caps,
+ },
+ {
+ .compatible = "marvell,pxa3xx-nand-controller",
+ .data = &marvell_pxa3xx_nfc_caps,
+ },
+ /* Support for old/deprecated bindings: */
+ {
+ .compatible = "marvell,armada-8k-nand",
+ .data = &marvell_armada_8k_nfc_legacy_caps,
+ },
+ {
+ .compatible = "marvell,armada370-nand",
+ .data = &marvell_armada370_nfc_legacy_caps,
+ },
+ {
+ .compatible = "marvell,pxa3xx-nand",
+ .data = &marvell_pxa3xx_nfc_legacy_caps,
+ },
+ { /* sentinel */ },
+};
+MODULE_DEVICE_TABLE(of, marvell_nfc_of_ids);
+
+static struct platform_driver marvell_nfc_driver = {
+ .driver = {
+ .name = "marvell-nfc",
+ .of_match_table = marvell_nfc_of_ids,
+ },
+ .id_table = marvell_nfc_platform_ids,
+ .probe = marvell_nfc_probe,
+ .remove = marvell_nfc_remove,
+};
+module_platform_driver(marvell_nfc_driver);
+
+MODULE_LICENSE("GPL");
+MODULE_DESCRIPTION("Marvell NAND controller driver");
--
2.11.0
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
^ permalink raw reply related [flat|nested] 19+ messages in thread* [PATCH v3 5/7] mtd: nand: use Marvell reworked NAND controller driver with all platforms
[not found] ` <20180109103637.23798-1-miquel.raynal-wi1+55ScJUtKEb57/3fJTNBPR1lH4CV8@public.gmane.org>
` (3 preceding siblings ...)
2018-01-09 10:36 ` [PATCH v3 4/7] mtd: nand: use reworked NAND controller driver with Marvell EBU SoCs Miquel Raynal
@ 2018-01-09 10:36 ` Miquel Raynal
[not found] ` <20180109103637.23798-6-miquel.raynal-wi1+55ScJUtKEb57/3fJTNBPR1lH4CV8@public.gmane.org>
2018-01-09 10:36 ` [PATCH v3 6/7] dt-bindings: mtd: remove pxa3xx NAND controller documentation Miquel Raynal
` (3 subsequent siblings)
8 siblings, 1 reply; 19+ messages in thread
From: Miquel Raynal @ 2018-01-09 10:36 UTC (permalink / raw)
To: David Woodhouse, Brian Norris, Boris Brezillon, Marek Vasut,
Richard Weinberger, Cyrille Pitchen, Rob Herring, Mark Rutland,
Jason Cooper, Andrew Lunn, Gregory Clement,
Sebastian Hesselbarth, Russell King, Daniel Mack, Haojian Zhuang,
Robert Jarzmik, Eric Miao, Catalin Marinas
Cc: linux-mtd-IAPFreCvJWM7uuMidbF8XUB+6BGkLq7r,
devicetree-u79uwXL29TY76Z2rM5mHXA,
linux-arm-kernel-IAPFreCvJWM7uuMidbF8XUB+6BGkLq7r,
Thomas Petazzoni, Antoine Tenart, Nadav Haklai, Miquel Raynal,
Ofer Heifetz, Hanna Hawa, Neta Zur Hershkovits, Willy Tarreau,
Sean Nyekjaer
Actually remove pxa3xx_nand.c to let marvell_nand.c be compiled instead.
Also change the defconfig files using it as well as some board files
depending on CONFIG_MTD_NAND_PXA3xx.
Signed-off-by: Miquel Raynal <miquel.raynal-wi1+55ScJUtKEb57/3fJTNBPR1lH4CV8@public.gmane.org>
---
arch/arm/configs/cm_x300_defconfig | 2 +-
arch/arm/configs/pxa3xx_defconfig | 3 +-
arch/arm/configs/pxa_defconfig | 2 +-
arch/arm/configs/raumfeld_defconfig | 2 +-
arch/arm/mach-mmp/ttc_dkb.c | 4 +-
arch/arm/mach-pxa/cm-x300.c | 2 +-
arch/arm/mach-pxa/colibri-pxa3xx.c | 2 +-
arch/arm/mach-pxa/colibri.h | 2 +-
arch/arm/mach-pxa/littleton.c | 4 +-
arch/arm/mach-pxa/mxm8x10.c | 4 +-
arch/arm/mach-pxa/zylonite.c | 4 +-
drivers/mtd/nand/Kconfig | 11 -
drivers/mtd/nand/Makefile | 1 -
drivers/mtd/nand/pxa3xx_nand.c | 2104 -----------------------------------
14 files changed, 15 insertions(+), 2132 deletions(-)
delete mode 100644 drivers/mtd/nand/pxa3xx_nand.c
diff --git a/arch/arm/configs/cm_x300_defconfig b/arch/arm/configs/cm_x300_defconfig
index c0418e03d180..5e349c625b71 100644
--- a/arch/arm/configs/cm_x300_defconfig
+++ b/arch/arm/configs/cm_x300_defconfig
@@ -49,7 +49,7 @@ CONFIG_UEVENT_HELPER_PATH="/sbin/hotplug"
CONFIG_MTD=y
CONFIG_MTD_BLOCK=y
CONFIG_MTD_NAND=y
-CONFIG_MTD_NAND_PXA3xx=y
+CONFIG_MTD_NAND_MARVELL=y
CONFIG_MTD_UBI=y
CONFIG_BLK_DEV_LOOP=y
CONFIG_BLK_DEV_RAM=y
diff --git a/arch/arm/configs/pxa3xx_defconfig b/arch/arm/configs/pxa3xx_defconfig
index bfea6874b0a1..3e0de035ab77 100644
--- a/arch/arm/configs/pxa3xx_defconfig
+++ b/arch/arm/configs/pxa3xx_defconfig
@@ -32,8 +32,7 @@ CONFIG_UEVENT_HELPER_PATH="/sbin/hotplug"
CONFIG_MTD=y
CONFIG_MTD_BLOCK=y
CONFIG_MTD_NAND=y
-CONFIG_MTD_NAND_PXA3xx=y
-CONFIG_MTD_NAND_PXA3xx_BUILTIN=y
+CONFIG_MTD_NAND_MARVELL=y
CONFIG_MTD_ONENAND=y
CONFIG_MTD_ONENAND_VERIFY_WRITE=y
CONFIG_MTD_ONENAND_GENERIC=y
diff --git a/arch/arm/configs/pxa_defconfig b/arch/arm/configs/pxa_defconfig
index 830e817a028a..934af8601f7d 100644
--- a/arch/arm/configs/pxa_defconfig
+++ b/arch/arm/configs/pxa_defconfig
@@ -198,7 +198,7 @@ CONFIG_MTD_NAND_DISKONCHIP_PROBE_ADDRESS=0x4000000
CONFIG_MTD_NAND_DISKONCHIP_PROBE_HIGH=y
CONFIG_MTD_NAND_DISKONCHIP_BBTWRITE=y
CONFIG_MTD_NAND_SHARPSL=m
-CONFIG_MTD_NAND_PXA3xx=m
+CONFIG_MTD_NAND_MARVELL=m
CONFIG_MTD_NAND_CM_X270=m
CONFIG_MTD_NAND_TMIO=m
CONFIG_MTD_NAND_BRCMNAND=m
diff --git a/arch/arm/configs/raumfeld_defconfig b/arch/arm/configs/raumfeld_defconfig
index 77a56c23c6ef..2dd56e9a484e 100644
--- a/arch/arm/configs/raumfeld_defconfig
+++ b/arch/arm/configs/raumfeld_defconfig
@@ -33,7 +33,7 @@ CONFIG_NFTL=y
CONFIG_NFTL_RW=y
CONFIG_MTD_BLOCK2MTD=y
CONFIG_MTD_NAND=y
-CONFIG_MTD_NAND_PXA3xx=y
+CONFIG_MTD_NAND_MARVELL=y
CONFIG_MTD_UBI=y
CONFIG_BLK_DEV_LOOP=y
CONFIG_ISL29003=y
diff --git a/arch/arm/mach-mmp/ttc_dkb.c b/arch/arm/mach-mmp/ttc_dkb.c
index d90c74fa614d..e0b6073c61a7 100644
--- a/arch/arm/mach-mmp/ttc_dkb.c
+++ b/arch/arm/mach-mmp/ttc_dkb.c
@@ -178,7 +178,7 @@ static struct mv_usb_platform_data ttc_usb_pdata = {
#endif
#endif
-#if IS_ENABLED(CONFIG_MTD_NAND_PXA3xx)
+#if IS_ENABLED(CONFIG_MTD_NAND_MARVELL)
static struct pxa3xx_nand_platform_data dkb_nand_info = {
.enable_arbiter = 1,
.num_cs = 1,
@@ -275,7 +275,7 @@ static void __init ttc_dkb_init(void)
/* on-chip devices */
pxa910_add_uart(1);
-#if IS_ENABLED(CONFIG_MTD_NAND_PXA3xx)
+#if IS_ENABLED(CONFIG_MTD_NAND_MARVELL)
pxa910_add_nand(&dkb_nand_info);
#endif
diff --git a/arch/arm/mach-pxa/cm-x300.c b/arch/arm/mach-pxa/cm-x300.c
index 868448d2cd82..fe1c76bca212 100644
--- a/arch/arm/mach-pxa/cm-x300.c
+++ b/arch/arm/mach-pxa/cm-x300.c
@@ -391,7 +391,7 @@ static void __init cm_x300_init_ac97(void)
static inline void cm_x300_init_ac97(void) {}
#endif
-#if defined(CONFIG_MTD_NAND_PXA3xx) || defined(CONFIG_MTD_NAND_PXA3xx_MODULE)
+#if IS_ENABLED(CONFIG_MTD_NAND_MARVELL)
static struct mtd_partition cm_x300_nand_partitions[] = {
[0] = {
.name = "OBM",
diff --git a/arch/arm/mach-pxa/colibri-pxa3xx.c b/arch/arm/mach-pxa/colibri-pxa3xx.c
index b04431bb4ba7..3018eafd723e 100644
--- a/arch/arm/mach-pxa/colibri-pxa3xx.c
+++ b/arch/arm/mach-pxa/colibri-pxa3xx.c
@@ -110,7 +110,7 @@ void __init colibri_pxa3xx_init_lcd(int bl_pin)
}
#endif
-#if defined(CONFIG_MTD_NAND_PXA3xx) || defined(CONFIG_MTD_NAND_PXA3xx_MODULE)
+#if IS_ENABLED(CONFIG_MTD_NAND_MARVELL)
static struct mtd_partition colibri_nand_partitions[] = {
{
.name = "bootloader",
diff --git a/arch/arm/mach-pxa/colibri.h b/arch/arm/mach-pxa/colibri.h
index 673a131da875..85525d49e321 100644
--- a/arch/arm/mach-pxa/colibri.h
+++ b/arch/arm/mach-pxa/colibri.h
@@ -46,7 +46,7 @@ static inline void colibri_pxa3xx_init_lcd(int bl_pin) {}
extern void colibri_pxa3xx_init_eth(struct ax_plat_data *plat_data);
#endif
-#if defined(CONFIG_MTD_NAND_PXA3xx) || defined(CONFIG_MTD_NAND_PXA3xx_MODULE)
+#if IS_ENABLED(CONFIG_MTD_NAND_MARVELL)
extern void colibri_pxa3xx_init_nand(void);
#else
static inline void colibri_pxa3xx_init_nand(void) {}
diff --git a/arch/arm/mach-pxa/littleton.c b/arch/arm/mach-pxa/littleton.c
index fae38fdc8d8e..380b07a15ef9 100644
--- a/arch/arm/mach-pxa/littleton.c
+++ b/arch/arm/mach-pxa/littleton.c
@@ -290,7 +290,7 @@ static void __init littleton_init_mmc(void)
static inline void littleton_init_mmc(void) {}
#endif
-#if defined(CONFIG_MTD_NAND_PXA3xx) || defined(CONFIG_MTD_NAND_PXA3xx_MODULE)
+#if IS_ENABLED(CONFIG_MTD_NAND_MARVELL)
static struct mtd_partition littleton_nand_partitions[] = {
[0] = {
.name = "Bootloader",
@@ -340,7 +340,7 @@ static void __init littleton_init_nand(void)
}
#else
static inline void littleton_init_nand(void) {}
-#endif /* CONFIG_MTD_NAND_PXA3xx || CONFIG_MTD_NAND_PXA3xx_MODULE */
+#endif /* IS_ENABLED(CONFIG_MTD_NAND_MARVELL) */
#if defined(CONFIG_I2C_PXA) || defined(CONFIG_I2C_PXA_MODULE)
static struct led_info littleton_da9034_leds[] = {
diff --git a/arch/arm/mach-pxa/mxm8x10.c b/arch/arm/mach-pxa/mxm8x10.c
index 9a22ae0ad8c9..743d983fc222 100644
--- a/arch/arm/mach-pxa/mxm8x10.c
+++ b/arch/arm/mach-pxa/mxm8x10.c
@@ -359,7 +359,7 @@ void __init mxm_8x10_ac97_init(void)
}
/* NAND flash Support */
-#if defined(CONFIG_MTD_NAND_PXA3xx) || defined(CONFIG_MTD_NAND_PXA3xx_MODULE)
+#if IS_ENABLED(CONFIG_MTD_NAND_MARVELL)
#define NAND_BLOCK_SIZE SZ_128K
#define NB(x) (NAND_BLOCK_SIZE * (x))
static struct mtd_partition mxm_8x10_nand_partitions[] = {
@@ -402,7 +402,7 @@ static void __init mxm_8x10_nand_init(void)
}
#else
static inline void mxm_8x10_nand_init(void) {}
-#endif /* CONFIG_MTD_NAND_PXA3xx || CONFIG_MTD_NAND_PXA3xx_MODULE */
+#endif /* IS_ENABLED(CONFIG_MTD_NAND_MARVELL) */
/* Ethernet support: Davicom DM9000 */
static struct resource dm9k_resources[] = {
diff --git a/arch/arm/mach-pxa/zylonite.c b/arch/arm/mach-pxa/zylonite.c
index 4268552d600d..3a99fc054e96 100644
--- a/arch/arm/mach-pxa/zylonite.c
+++ b/arch/arm/mach-pxa/zylonite.c
@@ -338,7 +338,7 @@ static void __init zylonite_init_keypad(void)
static inline void zylonite_init_keypad(void) {}
#endif
-#if defined(CONFIG_MTD_NAND_PXA3xx) || defined(CONFIG_MTD_NAND_PXA3xx_MODULE)
+#if IS_ENABLED(CONFIG_MTD_NAND_MARVELL)
static struct mtd_partition zylonite_nand_partitions[] = {
[0] = {
.name = "Bootloader",
@@ -388,7 +388,7 @@ static void __init zylonite_init_nand(void)
}
#else
static inline void zylonite_init_nand(void) {}
-#endif /* CONFIG_MTD_NAND_PXA3xx || CONFIG_MTD_NAND_PXA3xx_MODULE */
+#endif /* IS_ENABLED(CONFIG_MTD_NAND_MARVELL) */
#if defined(CONFIG_USB_OHCI_HCD) || defined(CONFIG_USB_OHCI_HCD_MODULE)
static struct pxaohci_platform_data zylonite_ohci_info = {
diff --git a/drivers/mtd/nand/Kconfig b/drivers/mtd/nand/Kconfig
index e6b8c59f2c0d..2c6ecb7ae753 100644
--- a/drivers/mtd/nand/Kconfig
+++ b/drivers/mtd/nand/Kconfig
@@ -313,17 +313,6 @@ config MTD_NAND_ATMEL
Enables support for NAND Flash / Smart Media Card interface
on Atmel AT91 processors.
-config MTD_NAND_PXA3xx
- tristate "NAND support on PXA3xx and Armada 370/XP"
- depends on !MTD_NAND_MARVELL
- depends on PXA3xx || ARCH_MMP || PLAT_ORION || ARCH_MVEBU
- help
-
- This enables the driver for the NAND flash device found on
- PXA3xx processors (NFCv1) and also on 32-bit Armada
- platforms (XP, 370, 375, 38x, 39x) and 64-bit Armada
- platforms (7K, 8K) (NFCv2).
-
config MTD_NAND_MARVELL
tristate "NAND controller support on Marvell boards"
depends on PXA3xx || ARCH_MMP || PLAT_ORION || ARCH_MVEBU || \
diff --git a/drivers/mtd/nand/Makefile b/drivers/mtd/nand/Makefile
index 921634ba400c..c882d5ef192a 100644
--- a/drivers/mtd/nand/Makefile
+++ b/drivers/mtd/nand/Makefile
@@ -31,7 +31,6 @@ omap2_nand-objs := omap2.o
obj-$(CONFIG_MTD_NAND_OMAP2) += omap2_nand.o
obj-$(CONFIG_MTD_NAND_OMAP_BCH_BUILD) += omap_elm.o
obj-$(CONFIG_MTD_NAND_CM_X270) += cmx270_nand.o
-obj-$(CONFIG_MTD_NAND_PXA3xx) += pxa3xx_nand.o
obj-$(CONFIG_MTD_NAND_MARVELL) += marvell_nand.o
obj-$(CONFIG_MTD_NAND_TMIO) += tmio_nand.o
obj-$(CONFIG_MTD_NAND_PLATFORM) += plat_nand.o
diff --git a/drivers/mtd/nand/pxa3xx_nand.c b/drivers/mtd/nand/pxa3xx_nand.c
deleted file mode 100644
index 021374fe59dc..000000000000
--- a/drivers/mtd/nand/pxa3xx_nand.c
+++ /dev/null
@@ -1,2104 +0,0 @@
-/*
- * drivers/mtd/nand/pxa3xx_nand.c
- *
- * Copyright © 2005 Intel Corporation
- * Copyright © 2006 Marvell International Ltd.
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License version 2 as
- * published by the Free Software Foundation.
- *
- * See Documentation/mtd/nand/pxa3xx-nand.txt for more details.
- */
-
-#include <linux/kernel.h>
-#include <linux/module.h>
-#include <linux/interrupt.h>
-#include <linux/platform_device.h>
-#include <linux/dmaengine.h>
-#include <linux/dma-mapping.h>
-#include <linux/dma/pxa-dma.h>
-#include <linux/delay.h>
-#include <linux/clk.h>
-#include <linux/mtd/mtd.h>
-#include <linux/mtd/rawnand.h>
-#include <linux/mtd/partitions.h>
-#include <linux/io.h>
-#include <linux/iopoll.h>
-#include <linux/irq.h>
-#include <linux/slab.h>
-#include <linux/of.h>
-#include <linux/of_device.h>
-#include <linux/platform_data/mtd-nand-pxa3xx.h>
-#include <linux/mfd/syscon.h>
-#include <linux/regmap.h>
-
-#define CHIP_DELAY_TIMEOUT msecs_to_jiffies(200)
-#define NAND_STOP_DELAY msecs_to_jiffies(40)
-#define PAGE_CHUNK_SIZE (2048)
-
-/*
- * Define a buffer size for the initial command that detects the flash device:
- * STATUS, READID and PARAM.
- * ONFI param page is 256 bytes, and there are three redundant copies
- * to be read. JEDEC param page is 512 bytes, and there are also three
- * redundant copies to be read.
- * Hence this buffer should be at least 512 x 3. Let's pick 2048.
- */
-#define INIT_BUFFER_SIZE 2048
-
-/* System control register and bit to enable NAND on some SoCs */
-#define GENCONF_SOC_DEVICE_MUX 0x208
-#define GENCONF_SOC_DEVICE_MUX_NFC_EN BIT(0)
-
-/* registers and bit definitions */
-#define NDCR (0x00) /* Control register */
-#define NDTR0CS0 (0x04) /* Timing Parameter 0 for CS0 */
-#define NDTR1CS0 (0x0C) /* Timing Parameter 1 for CS0 */
-#define NDSR (0x14) /* Status Register */
-#define NDPCR (0x18) /* Page Count Register */
-#define NDBDR0 (0x1C) /* Bad Block Register 0 */
-#define NDBDR1 (0x20) /* Bad Block Register 1 */
-#define NDECCCTRL (0x28) /* ECC control */
-#define NDDB (0x40) /* Data Buffer */
-#define NDCB0 (0x48) /* Command Buffer0 */
-#define NDCB1 (0x4C) /* Command Buffer1 */
-#define NDCB2 (0x50) /* Command Buffer2 */
-
-#define NDCR_SPARE_EN (0x1 << 31)
-#define NDCR_ECC_EN (0x1 << 30)
-#define NDCR_DMA_EN (0x1 << 29)
-#define NDCR_ND_RUN (0x1 << 28)
-#define NDCR_DWIDTH_C (0x1 << 27)
-#define NDCR_DWIDTH_M (0x1 << 26)
-#define NDCR_PAGE_SZ (0x1 << 24)
-#define NDCR_NCSX (0x1 << 23)
-#define NDCR_ND_MODE (0x3 << 21)
-#define NDCR_NAND_MODE (0x0)
-#define NDCR_CLR_PG_CNT (0x1 << 20)
-#define NFCV1_NDCR_ARB_CNTL (0x1 << 19)
-#define NFCV2_NDCR_STOP_ON_UNCOR (0x1 << 19)
-#define NDCR_RD_ID_CNT_MASK (0x7 << 16)
-#define NDCR_RD_ID_CNT(x) (((x) << 16) & NDCR_RD_ID_CNT_MASK)
-
-#define NDCR_RA_START (0x1 << 15)
-#define NDCR_PG_PER_BLK (0x1 << 14)
-#define NDCR_ND_ARB_EN (0x1 << 12)
-#define NDCR_INT_MASK (0xFFF)
-
-#define NDSR_MASK (0xfff)
-#define NDSR_ERR_CNT_OFF (16)
-#define NDSR_ERR_CNT_MASK (0x1f)
-#define NDSR_ERR_CNT(sr) ((sr >> NDSR_ERR_CNT_OFF) & NDSR_ERR_CNT_MASK)
-#define NDSR_RDY (0x1 << 12)
-#define NDSR_FLASH_RDY (0x1 << 11)
-#define NDSR_CS0_PAGED (0x1 << 10)
-#define NDSR_CS1_PAGED (0x1 << 9)
-#define NDSR_CS0_CMDD (0x1 << 8)
-#define NDSR_CS1_CMDD (0x1 << 7)
-#define NDSR_CS0_BBD (0x1 << 6)
-#define NDSR_CS1_BBD (0x1 << 5)
-#define NDSR_UNCORERR (0x1 << 4)
-#define NDSR_CORERR (0x1 << 3)
-#define NDSR_WRDREQ (0x1 << 2)
-#define NDSR_RDDREQ (0x1 << 1)
-#define NDSR_WRCMDREQ (0x1)
-
-#define NDCB0_LEN_OVRD (0x1 << 28)
-#define NDCB0_ST_ROW_EN (0x1 << 26)
-#define NDCB0_AUTO_RS (0x1 << 25)
-#define NDCB0_CSEL (0x1 << 24)
-#define NDCB0_EXT_CMD_TYPE_MASK (0x7 << 29)
-#define NDCB0_EXT_CMD_TYPE(x) (((x) << 29) & NDCB0_EXT_CMD_TYPE_MASK)
-#define NDCB0_CMD_TYPE_MASK (0x7 << 21)
-#define NDCB0_CMD_TYPE(x) (((x) << 21) & NDCB0_CMD_TYPE_MASK)
-#define NDCB0_NC (0x1 << 20)
-#define NDCB0_DBC (0x1 << 19)
-#define NDCB0_ADDR_CYC_MASK (0x7 << 16)
-#define NDCB0_ADDR_CYC(x) (((x) << 16) & NDCB0_ADDR_CYC_MASK)
-#define NDCB0_CMD2_MASK (0xff << 8)
-#define NDCB0_CMD1_MASK (0xff)
-#define NDCB0_ADDR_CYC_SHIFT (16)
-
-#define EXT_CMD_TYPE_DISPATCH 6 /* Command dispatch */
-#define EXT_CMD_TYPE_NAKED_RW 5 /* Naked read or Naked write */
-#define EXT_CMD_TYPE_READ 4 /* Read */
-#define EXT_CMD_TYPE_DISP_WR 4 /* Command dispatch with write */
-#define EXT_CMD_TYPE_FINAL 3 /* Final command */
-#define EXT_CMD_TYPE_LAST_RW 1 /* Last naked read/write */
-#define EXT_CMD_TYPE_MONO 0 /* Monolithic read/write */
-
-/*
- * This should be large enough to read 'ONFI' and 'JEDEC'.
- * Let's use 7 bytes, which is the maximum ID count supported
- * by the controller (see NDCR_RD_ID_CNT_MASK).
- */
-#define READ_ID_BYTES 7
-
-/* macros for registers read/write */
-#define nand_writel(info, off, val) \
- do { \
- dev_vdbg(&info->pdev->dev, \
- "%s():%d nand_writel(0x%x, 0x%04x)\n", \
- __func__, __LINE__, (val), (off)); \
- writel_relaxed((val), (info)->mmio_base + (off)); \
- } while (0)
-
-#define nand_readl(info, off) \
- ({ \
- unsigned int _v; \
- _v = readl_relaxed((info)->mmio_base + (off)); \
- dev_vdbg(&info->pdev->dev, \
- "%s():%d nand_readl(0x%04x) = 0x%x\n", \
- __func__, __LINE__, (off), _v); \
- _v; \
- })
-
-/* error code and state */
-enum {
- ERR_NONE = 0,
- ERR_DMABUSERR = -1,
- ERR_SENDCMD = -2,
- ERR_UNCORERR = -3,
- ERR_BBERR = -4,
- ERR_CORERR = -5,
-};
-
-enum {
- STATE_IDLE = 0,
- STATE_PREPARED,
- STATE_CMD_HANDLE,
- STATE_DMA_READING,
- STATE_DMA_WRITING,
- STATE_DMA_DONE,
- STATE_PIO_READING,
- STATE_PIO_WRITING,
- STATE_CMD_DONE,
- STATE_READY,
-};
-
-enum pxa3xx_nand_variant {
- PXA3XX_NAND_VARIANT_PXA,
- PXA3XX_NAND_VARIANT_ARMADA370,
- PXA3XX_NAND_VARIANT_ARMADA_8K,
-};
-
-struct pxa3xx_nand_host {
- struct nand_chip chip;
- void *info_data;
-
- /* page size of attached chip */
- int use_ecc;
- int cs;
-
- /* calculated from pxa3xx_nand_flash data */
- unsigned int col_addr_cycles;
- unsigned int row_addr_cycles;
-};
-
-struct pxa3xx_nand_info {
- struct nand_hw_control controller;
- struct platform_device *pdev;
-
- struct clk *clk;
- void __iomem *mmio_base;
- unsigned long mmio_phys;
- struct completion cmd_complete, dev_ready;
-
- unsigned int buf_start;
- unsigned int buf_count;
- unsigned int buf_size;
- unsigned int data_buff_pos;
- unsigned int oob_buff_pos;
-
- /* DMA information */
- struct scatterlist sg;
- enum dma_data_direction dma_dir;
- struct dma_chan *dma_chan;
- dma_cookie_t dma_cookie;
- int drcmr_dat;
-
- unsigned char *data_buff;
- unsigned char *oob_buff;
- dma_addr_t data_buff_phys;
- int data_dma_ch;
-
- struct pxa3xx_nand_host *host[NUM_CHIP_SELECT];
- unsigned int state;
-
- /*
- * This driver supports NFCv1 (as found in PXA SoC)
- * and NFCv2 (as found in Armada 370/XP SoC).
- */
- enum pxa3xx_nand_variant variant;
-
- int cs;
- int use_ecc; /* use HW ECC ? */
- int ecc_bch; /* using BCH ECC? */
- int use_dma; /* use DMA ? */
- int use_spare; /* use spare ? */
- int need_wait;
-
- /* Amount of real data per full chunk */
- unsigned int chunk_size;
-
- /* Amount of spare data per full chunk */
- unsigned int spare_size;
-
- /* Number of full chunks (i.e chunk_size + spare_size) */
- unsigned int nfullchunks;
-
- /*
- * Total number of chunks. If equal to nfullchunks, then there
- * are only full chunks. Otherwise, there is one last chunk of
- * size (last_chunk_size + last_spare_size)
- */
- unsigned int ntotalchunks;
-
- /* Amount of real data in the last chunk */
- unsigned int last_chunk_size;
-
- /* Amount of spare data in the last chunk */
- unsigned int last_spare_size;
-
- unsigned int ecc_size;
- unsigned int ecc_err_cnt;
- unsigned int max_bitflips;
- int retcode;
-
- /*
- * Variables only valid during command
- * execution. step_chunk_size and step_spare_size is the
- * amount of real data and spare data in the current
- * chunk. cur_chunk is the current chunk being
- * read/programmed.
- */
- unsigned int step_chunk_size;
- unsigned int step_spare_size;
- unsigned int cur_chunk;
-
- /* cached register value */
- uint32_t reg_ndcr;
- uint32_t ndtr0cs0;
- uint32_t ndtr1cs0;
-
- /* generated NDCBx register values */
- uint32_t ndcb0;
- uint32_t ndcb1;
- uint32_t ndcb2;
- uint32_t ndcb3;
-};
-
-static bool use_dma = 1;
-module_param(use_dma, bool, 0444);
-MODULE_PARM_DESC(use_dma, "enable DMA for data transferring to/from NAND HW");
-
-struct pxa3xx_nand_timing {
- unsigned int tCH; /* Enable signal hold time */
- unsigned int tCS; /* Enable signal setup time */
- unsigned int tWH; /* ND_nWE high duration */
- unsigned int tWP; /* ND_nWE pulse time */
- unsigned int tRH; /* ND_nRE high duration */
- unsigned int tRP; /* ND_nRE pulse width */
- unsigned int tR; /* ND_nWE high to ND_nRE low for read */
- unsigned int tWHR; /* ND_nWE high to ND_nRE low for status read */
- unsigned int tAR; /* ND_ALE low to ND_nRE low delay */
-};
-
-struct pxa3xx_nand_flash {
- uint32_t chip_id;
- unsigned int flash_width; /* Width of Flash memory (DWIDTH_M) */
- unsigned int dfc_width; /* Width of flash controller(DWIDTH_C) */
- struct pxa3xx_nand_timing *timing; /* NAND Flash timing */
-};
-
-static struct pxa3xx_nand_timing timing[] = {
- { 40, 80, 60, 100, 80, 100, 90000, 400, 40, },
- { 10, 0, 20, 40, 30, 40, 11123, 110, 10, },
- { 10, 25, 15, 25, 15, 30, 25000, 60, 10, },
- { 10, 35, 15, 25, 15, 25, 25000, 60, 10, },
-};
-
-static struct pxa3xx_nand_flash builtin_flash_types[] = {
- { 0x46ec, 16, 16, &timing[1] },
- { 0xdaec, 8, 8, &timing[1] },
- { 0xd7ec, 8, 8, &timing[1] },
- { 0xa12c, 8, 8, &timing[2] },
- { 0xb12c, 16, 16, &timing[2] },
- { 0xdc2c, 8, 8, &timing[2] },
- { 0xcc2c, 16, 16, &timing[2] },
- { 0xba20, 16, 16, &timing[3] },
-};
-
-static int pxa3xx_ooblayout_ecc(struct mtd_info *mtd, int section,
- struct mtd_oob_region *oobregion)
-{
- struct nand_chip *chip = mtd_to_nand(mtd);
- struct pxa3xx_nand_host *host = nand_get_controller_data(chip);
- struct pxa3xx_nand_info *info = host->info_data;
- int nchunks = mtd->writesize / info->chunk_size;
-
- if (section >= nchunks)
- return -ERANGE;
-
- oobregion->offset = ((info->ecc_size + info->spare_size) * section) +
- info->spare_size;
- oobregion->length = info->ecc_size;
-
- return 0;
-}
-
-static int pxa3xx_ooblayout_free(struct mtd_info *mtd, int section,
- struct mtd_oob_region *oobregion)
-{
- struct nand_chip *chip = mtd_to_nand(mtd);
- struct pxa3xx_nand_host *host = nand_get_controller_data(chip);
- struct pxa3xx_nand_info *info = host->info_data;
- int nchunks = mtd->writesize / info->chunk_size;
-
- if (section >= nchunks)
- return -ERANGE;
-
- if (!info->spare_size)
- return 0;
-
- oobregion->offset = section * (info->ecc_size + info->spare_size);
- oobregion->length = info->spare_size;
- if (!section) {
- /*
- * Bootrom looks in bytes 0 & 5 for bad blocks for the
- * 4KB page / 4bit BCH combination.
- */
- if (mtd->writesize == 4096 && info->chunk_size == 2048) {
- oobregion->offset += 6;
- oobregion->length -= 6;
- } else {
- oobregion->offset += 2;
- oobregion->length -= 2;
- }
- }
-
- return 0;
-}
-
-static const struct mtd_ooblayout_ops pxa3xx_ooblayout_ops = {
- .ecc = pxa3xx_ooblayout_ecc,
- .free = pxa3xx_ooblayout_free,
-};
-
-static u8 bbt_pattern[] = {'M', 'V', 'B', 'b', 't', '0' };
-static u8 bbt_mirror_pattern[] = {'1', 't', 'b', 'B', 'V', 'M' };
-
-static struct nand_bbt_descr bbt_main_descr = {
- .options = NAND_BBT_LASTBLOCK | NAND_BBT_CREATE | NAND_BBT_WRITE
- | NAND_BBT_2BIT | NAND_BBT_VERSION,
- .offs = 8,
- .len = 6,
- .veroffs = 14,
- .maxblocks = 8, /* Last 8 blocks in each chip */
- .pattern = bbt_pattern
-};
-
-static struct nand_bbt_descr bbt_mirror_descr = {
- .options = NAND_BBT_LASTBLOCK | NAND_BBT_CREATE | NAND_BBT_WRITE
- | NAND_BBT_2BIT | NAND_BBT_VERSION,
- .offs = 8,
- .len = 6,
- .veroffs = 14,
- .maxblocks = 8, /* Last 8 blocks in each chip */
- .pattern = bbt_mirror_pattern
-};
-
-#define NDTR0_tCH(c) (min((c), 7) << 19)
-#define NDTR0_tCS(c) (min((c), 7) << 16)
-#define NDTR0_tWH(c) (min((c), 7) << 11)
-#define NDTR0_tWP(c) (min((c), 7) << 8)
-#define NDTR0_tRH(c) (min((c), 7) << 3)
-#define NDTR0_tRP(c) (min((c), 7) << 0)
-
-#define NDTR1_tR(c) (min((c), 65535) << 16)
-#define NDTR1_tWHR(c) (min((c), 15) << 4)
-#define NDTR1_tAR(c) (min((c), 15) << 0)
-
-/* convert nano-seconds to nand flash controller clock cycles */
-#define ns2cycle(ns, clk) (int)((ns) * (clk / 1000000) / 1000)
-
-static const struct of_device_id pxa3xx_nand_dt_ids[] = {
- {
- .compatible = "marvell,pxa3xx-nand",
- .data = (void *)PXA3XX_NAND_VARIANT_PXA,
- },
- {
- .compatible = "marvell,armada370-nand",
- .data = (void *)PXA3XX_NAND_VARIANT_ARMADA370,
- },
- {
- .compatible = "marvell,armada-8k-nand",
- .data = (void *)PXA3XX_NAND_VARIANT_ARMADA_8K,
- },
- {}
-};
-MODULE_DEVICE_TABLE(of, pxa3xx_nand_dt_ids);
-
-static enum pxa3xx_nand_variant
-pxa3xx_nand_get_variant(struct platform_device *pdev)
-{
- const struct of_device_id *of_id =
- of_match_device(pxa3xx_nand_dt_ids, &pdev->dev);
- if (!of_id)
- return PXA3XX_NAND_VARIANT_PXA;
- return (enum pxa3xx_nand_variant)of_id->data;
-}
-
-static void pxa3xx_nand_set_timing(struct pxa3xx_nand_host *host,
- const struct pxa3xx_nand_timing *t)
-{
- struct pxa3xx_nand_info *info = host->info_data;
- unsigned long nand_clk = clk_get_rate(info->clk);
- uint32_t ndtr0, ndtr1;
-
- ndtr0 = NDTR0_tCH(ns2cycle(t->tCH, nand_clk)) |
- NDTR0_tCS(ns2cycle(t->tCS, nand_clk)) |
- NDTR0_tWH(ns2cycle(t->tWH, nand_clk)) |
- NDTR0_tWP(ns2cycle(t->tWP, nand_clk)) |
- NDTR0_tRH(ns2cycle(t->tRH, nand_clk)) |
- NDTR0_tRP(ns2cycle(t->tRP, nand_clk));
-
- ndtr1 = NDTR1_tR(ns2cycle(t->tR, nand_clk)) |
- NDTR1_tWHR(ns2cycle(t->tWHR, nand_clk)) |
- NDTR1_tAR(ns2cycle(t->tAR, nand_clk));
-
- info->ndtr0cs0 = ndtr0;
- info->ndtr1cs0 = ndtr1;
- nand_writel(info, NDTR0CS0, ndtr0);
- nand_writel(info, NDTR1CS0, ndtr1);
-}
-
-static void pxa3xx_nand_set_sdr_timing(struct pxa3xx_nand_host *host,
- const struct nand_sdr_timings *t)
-{
- struct pxa3xx_nand_info *info = host->info_data;
- struct nand_chip *chip = &host->chip;
- unsigned long nand_clk = clk_get_rate(info->clk);
- uint32_t ndtr0, ndtr1;
-
- u32 tCH_min = DIV_ROUND_UP(t->tCH_min, 1000);
- u32 tCS_min = DIV_ROUND_UP(t->tCS_min, 1000);
- u32 tWH_min = DIV_ROUND_UP(t->tWH_min, 1000);
- u32 tWP_min = DIV_ROUND_UP(t->tWC_min - t->tWH_min, 1000);
- u32 tREH_min = DIV_ROUND_UP(t->tREH_min, 1000);
- u32 tRP_min = DIV_ROUND_UP(t->tRC_min - t->tREH_min, 1000);
- u32 tR = chip->chip_delay * 1000;
- u32 tWHR_min = DIV_ROUND_UP(t->tWHR_min, 1000);
- u32 tAR_min = DIV_ROUND_UP(t->tAR_min, 1000);
-
- /* fallback to a default value if tR = 0 */
- if (!tR)
- tR = 20000;
-
- ndtr0 = NDTR0_tCH(ns2cycle(tCH_min, nand_clk)) |
- NDTR0_tCS(ns2cycle(tCS_min, nand_clk)) |
- NDTR0_tWH(ns2cycle(tWH_min, nand_clk)) |
- NDTR0_tWP(ns2cycle(tWP_min, nand_clk)) |
- NDTR0_tRH(ns2cycle(tREH_min, nand_clk)) |
- NDTR0_tRP(ns2cycle(tRP_min, nand_clk));
-
- ndtr1 = NDTR1_tR(ns2cycle(tR, nand_clk)) |
- NDTR1_tWHR(ns2cycle(tWHR_min, nand_clk)) |
- NDTR1_tAR(ns2cycle(tAR_min, nand_clk));
-
- info->ndtr0cs0 = ndtr0;
- info->ndtr1cs0 = ndtr1;
- nand_writel(info, NDTR0CS0, ndtr0);
- nand_writel(info, NDTR1CS0, ndtr1);
-}
-
-static int pxa3xx_nand_init_timings_compat(struct pxa3xx_nand_host *host,
- unsigned int *flash_width,
- unsigned int *dfc_width)
-{
- struct nand_chip *chip = &host->chip;
- struct pxa3xx_nand_info *info = host->info_data;
- const struct pxa3xx_nand_flash *f = NULL;
- int i, id, ntypes;
- u8 idbuf[2];
-
- ntypes = ARRAY_SIZE(builtin_flash_types);
-
- nand_readid_op(chip, 0, idbuf, sizeof(idbuf));
- id = idbuf[0] | (idbuf[1] << 8);
-
- for (i = 0; i < ntypes; i++) {
- f = &builtin_flash_types[i];
-
- if (f->chip_id == id)
- break;
- }
-
- if (i == ntypes) {
- dev_err(&info->pdev->dev, "Error: timings not found\n");
- return -EINVAL;
- }
-
- pxa3xx_nand_set_timing(host, f->timing);
-
- *flash_width = f->flash_width;
- *dfc_width = f->dfc_width;
-
- return 0;
-}
-
-static int pxa3xx_nand_init_timings_onfi(struct pxa3xx_nand_host *host,
- int mode)
-{
- const struct nand_sdr_timings *timings;
-
- mode = fls(mode) - 1;
- if (mode < 0)
- mode = 0;
-
- timings = onfi_async_timing_mode_to_sdr_timings(mode);
- if (IS_ERR(timings))
- return PTR_ERR(timings);
-
- pxa3xx_nand_set_sdr_timing(host, timings);
-
- return 0;
-}
-
-static int pxa3xx_nand_init(struct pxa3xx_nand_host *host)
-{
- struct nand_chip *chip = &host->chip;
- struct pxa3xx_nand_info *info = host->info_data;
- unsigned int flash_width = 0, dfc_width = 0;
- int mode, err;
-
- mode = onfi_get_async_timing_mode(chip);
- if (mode == ONFI_TIMING_MODE_UNKNOWN) {
- err = pxa3xx_nand_init_timings_compat(host, &flash_width,
- &dfc_width);
- if (err)
- return err;
-
- if (flash_width == 16) {
- info->reg_ndcr |= NDCR_DWIDTH_M;
- chip->options |= NAND_BUSWIDTH_16;
- }
-
- info->reg_ndcr |= (dfc_width == 16) ? NDCR_DWIDTH_C : 0;
- } else {
- err = pxa3xx_nand_init_timings_onfi(host, mode);
- if (err)
- return err;
- }
-
- return 0;
-}
-
-/**
- * NOTE: it is a must to set ND_RUN firstly, then write
- * command buffer, otherwise, it does not work.
- * We enable all the interrupt at the same time, and
- * let pxa3xx_nand_irq to handle all logic.
- */
-static void pxa3xx_nand_start(struct pxa3xx_nand_info *info)
-{
- uint32_t ndcr;
-
- ndcr = info->reg_ndcr;
-
- if (info->use_ecc) {
- ndcr |= NDCR_ECC_EN;
- if (info->ecc_bch)
- nand_writel(info, NDECCCTRL, 0x1);
- } else {
- ndcr &= ~NDCR_ECC_EN;
- if (info->ecc_bch)
- nand_writel(info, NDECCCTRL, 0x0);
- }
-
- if (info->use_dma)
- ndcr |= NDCR_DMA_EN;
- else
- ndcr &= ~NDCR_DMA_EN;
-
- if (info->use_spare)
- ndcr |= NDCR_SPARE_EN;
- else
- ndcr &= ~NDCR_SPARE_EN;
-
- ndcr |= NDCR_ND_RUN;
-
- /* clear status bits and run */
- nand_writel(info, NDSR, NDSR_MASK);
- nand_writel(info, NDCR, 0);
- nand_writel(info, NDCR, ndcr);
-}
-
-static void pxa3xx_nand_stop(struct pxa3xx_nand_info *info)
-{
- uint32_t ndcr;
- int timeout = NAND_STOP_DELAY;
-
- /* wait RUN bit in NDCR become 0 */
- ndcr = nand_readl(info, NDCR);
- while ((ndcr & NDCR_ND_RUN) && (timeout-- > 0)) {
- ndcr = nand_readl(info, NDCR);
- udelay(1);
- }
-
- if (timeout <= 0) {
- ndcr &= ~NDCR_ND_RUN;
- nand_writel(info, NDCR, ndcr);
- }
- if (info->dma_chan)
- dmaengine_terminate_all(info->dma_chan);
-
- /* clear status bits */
- nand_writel(info, NDSR, NDSR_MASK);
-}
-
-static void __maybe_unused
-enable_int(struct pxa3xx_nand_info *info, uint32_t int_mask)
-{
- uint32_t ndcr;
-
- ndcr = nand_readl(info, NDCR);
- nand_writel(info, NDCR, ndcr & ~int_mask);
-}
-
-static void disable_int(struct pxa3xx_nand_info *info, uint32_t int_mask)
-{
- uint32_t ndcr;
-
- ndcr = nand_readl(info, NDCR);
- nand_writel(info, NDCR, ndcr | int_mask);
-}
-
-static void drain_fifo(struct pxa3xx_nand_info *info, void *data, int len)
-{
- if (info->ecc_bch) {
- u32 val;
- int ret;
-
- /*
- * According to the datasheet, when reading from NDDB
- * with BCH enabled, after each 32 bytes reads, we
- * have to make sure that the NDSR.RDDREQ bit is set.
- *
- * Drain the FIFO 8 32 bits reads at a time, and skip
- * the polling on the last read.
- */
- while (len > 8) {
- ioread32_rep(info->mmio_base + NDDB, data, 8);
-
- ret = readl_relaxed_poll_timeout(info->mmio_base + NDSR, val,
- val & NDSR_RDDREQ, 1000, 5000);
- if (ret) {
- dev_err(&info->pdev->dev,
- "Timeout on RDDREQ while draining the FIFO\n");
- return;
- }
-
- data += 32;
- len -= 8;
- }
- }
-
- ioread32_rep(info->mmio_base + NDDB, data, len);
-}
-
-static void handle_data_pio(struct pxa3xx_nand_info *info)
-{
- switch (info->state) {
- case STATE_PIO_WRITING:
- if (info->step_chunk_size)
- writesl(info->mmio_base + NDDB,
- info->data_buff + info->data_buff_pos,
- DIV_ROUND_UP(info->step_chunk_size, 4));
-
- if (info->step_spare_size)
- writesl(info->mmio_base + NDDB,
- info->oob_buff + info->oob_buff_pos,
- DIV_ROUND_UP(info->step_spare_size, 4));
- break;
- case STATE_PIO_READING:
- if (info->step_chunk_size)
- drain_fifo(info,
- info->data_buff + info->data_buff_pos,
- DIV_ROUND_UP(info->step_chunk_size, 4));
-
- if (info->step_spare_size)
- drain_fifo(info,
- info->oob_buff + info->oob_buff_pos,
- DIV_ROUND_UP(info->step_spare_size, 4));
- break;
- default:
- dev_err(&info->pdev->dev, "%s: invalid state %d\n", __func__,
- info->state);
- BUG();
- }
-
- /* Update buffer pointers for multi-page read/write */
- info->data_buff_pos += info->step_chunk_size;
- info->oob_buff_pos += info->step_spare_size;
-}
-
-static void pxa3xx_nand_data_dma_irq(void *data)
-{
- struct pxa3xx_nand_info *info = data;
- struct dma_tx_state state;
- enum dma_status status;
-
- status = dmaengine_tx_status(info->dma_chan, info->dma_cookie, &state);
- if (likely(status == DMA_COMPLETE)) {
- info->state = STATE_DMA_DONE;
- } else {
- dev_err(&info->pdev->dev, "DMA error on data channel\n");
- info->retcode = ERR_DMABUSERR;
- }
- dma_unmap_sg(info->dma_chan->device->dev, &info->sg, 1, info->dma_dir);
-
- nand_writel(info, NDSR, NDSR_WRDREQ | NDSR_RDDREQ);
- enable_int(info, NDCR_INT_MASK);
-}
-
-static void start_data_dma(struct pxa3xx_nand_info *info)
-{
- enum dma_transfer_direction direction;
- struct dma_async_tx_descriptor *tx;
-
- switch (info->state) {
- case STATE_DMA_WRITING:
- info->dma_dir = DMA_TO_DEVICE;
- direction = DMA_MEM_TO_DEV;
- break;
- case STATE_DMA_READING:
- info->dma_dir = DMA_FROM_DEVICE;
- direction = DMA_DEV_TO_MEM;
- break;
- default:
- dev_err(&info->pdev->dev, "%s: invalid state %d\n", __func__,
- info->state);
- BUG();
- }
- info->sg.length = info->chunk_size;
- if (info->use_spare)
- info->sg.length += info->spare_size + info->ecc_size;
- dma_map_sg(info->dma_chan->device->dev, &info->sg, 1, info->dma_dir);
-
- tx = dmaengine_prep_slave_sg(info->dma_chan, &info->sg, 1, direction,
- DMA_PREP_INTERRUPT);
- if (!tx) {
- dev_err(&info->pdev->dev, "prep_slave_sg() failed\n");
- return;
- }
- tx->callback = pxa3xx_nand_data_dma_irq;
- tx->callback_param = info;
- info->dma_cookie = dmaengine_submit(tx);
- dma_async_issue_pending(info->dma_chan);
- dev_dbg(&info->pdev->dev, "%s(dir=%d cookie=%x size=%u)\n",
- __func__, direction, info->dma_cookie, info->sg.length);
-}
-
-static irqreturn_t pxa3xx_nand_irq_thread(int irq, void *data)
-{
- struct pxa3xx_nand_info *info = data;
-
- handle_data_pio(info);
-
- info->state = STATE_CMD_DONE;
- nand_writel(info, NDSR, NDSR_WRDREQ | NDSR_RDDREQ);
-
- return IRQ_HANDLED;
-}
-
-static irqreturn_t pxa3xx_nand_irq(int irq, void *devid)
-{
- struct pxa3xx_nand_info *info = devid;
- unsigned int status, is_completed = 0, is_ready = 0;
- unsigned int ready, cmd_done;
- irqreturn_t ret = IRQ_HANDLED;
-
- if (info->cs == 0) {
- ready = NDSR_FLASH_RDY;
- cmd_done = NDSR_CS0_CMDD;
- } else {
- ready = NDSR_RDY;
- cmd_done = NDSR_CS1_CMDD;
- }
-
- status = nand_readl(info, NDSR);
-
- if (status & NDSR_UNCORERR)
- info->retcode = ERR_UNCORERR;
- if (status & NDSR_CORERR) {
- info->retcode = ERR_CORERR;
- if ((info->variant == PXA3XX_NAND_VARIANT_ARMADA370 ||
- info->variant == PXA3XX_NAND_VARIANT_ARMADA_8K) &&
- info->ecc_bch)
- info->ecc_err_cnt = NDSR_ERR_CNT(status);
- else
- info->ecc_err_cnt = 1;
-
- /*
- * Each chunk composing a page is corrected independently,
- * and we need to store maximum number of corrected bitflips
- * to return it to the MTD layer in ecc.read_page().
- */
- info->max_bitflips = max_t(unsigned int,
- info->max_bitflips,
- info->ecc_err_cnt);
- }
- if (status & (NDSR_RDDREQ | NDSR_WRDREQ)) {
- /* whether use dma to transfer data */
- if (info->use_dma) {
- disable_int(info, NDCR_INT_MASK);
- info->state = (status & NDSR_RDDREQ) ?
- STATE_DMA_READING : STATE_DMA_WRITING;
- start_data_dma(info);
- goto NORMAL_IRQ_EXIT;
- } else {
- info->state = (status & NDSR_RDDREQ) ?
- STATE_PIO_READING : STATE_PIO_WRITING;
- ret = IRQ_WAKE_THREAD;
- goto NORMAL_IRQ_EXIT;
- }
- }
- if (status & cmd_done) {
- info->state = STATE_CMD_DONE;
- is_completed = 1;
- }
- if (status & ready) {
- info->state = STATE_READY;
- is_ready = 1;
- }
-
- /*
- * Clear all status bit before issuing the next command, which
- * can and will alter the status bits and will deserve a new
- * interrupt on its own. This lets the controller exit the IRQ
- */
- nand_writel(info, NDSR, status);
-
- if (status & NDSR_WRCMDREQ) {
- status &= ~NDSR_WRCMDREQ;
- info->state = STATE_CMD_HANDLE;
-
- /*
- * Command buffer registers NDCB{0-2} (and optionally NDCB3)
- * must be loaded by writing directly either 12 or 16
- * bytes directly to NDCB0, four bytes at a time.
- *
- * Direct write access to NDCB1, NDCB2 and NDCB3 is ignored
- * but each NDCBx register can be read.
- */
- nand_writel(info, NDCB0, info->ndcb0);
- nand_writel(info, NDCB0, info->ndcb1);
- nand_writel(info, NDCB0, info->ndcb2);
-
- /* NDCB3 register is available in NFCv2 (Armada 370/XP SoC) */
- if (info->variant == PXA3XX_NAND_VARIANT_ARMADA370 ||
- info->variant == PXA3XX_NAND_VARIANT_ARMADA_8K)
- nand_writel(info, NDCB0, info->ndcb3);
- }
-
- if (is_completed)
- complete(&info->cmd_complete);
- if (is_ready)
- complete(&info->dev_ready);
-NORMAL_IRQ_EXIT:
- return ret;
-}
-
-static inline int is_buf_blank(uint8_t *buf, size_t len)
-{
- for (; len > 0; len--)
- if (*buf++ != 0xff)
- return 0;
- return 1;
-}
-
-static void set_command_address(struct pxa3xx_nand_info *info,
- unsigned int page_size, uint16_t column, int page_addr)
-{
- /* small page addr setting */
- if (page_size < PAGE_CHUNK_SIZE) {
- info->ndcb1 = ((page_addr & 0xFFFFFF) << 8)
- | (column & 0xFF);
-
- info->ndcb2 = 0;
- } else {
- info->ndcb1 = ((page_addr & 0xFFFF) << 16)
- | (column & 0xFFFF);
-
- if (page_addr & 0xFF0000)
- info->ndcb2 = (page_addr & 0xFF0000) >> 16;
- else
- info->ndcb2 = 0;
- }
-}
-
-static void prepare_start_command(struct pxa3xx_nand_info *info, int command)
-{
- struct pxa3xx_nand_host *host = info->host[info->cs];
- struct mtd_info *mtd = nand_to_mtd(&host->chip);
-
- /* reset data and oob column point to handle data */
- info->buf_start = 0;
- info->buf_count = 0;
- info->data_buff_pos = 0;
- info->oob_buff_pos = 0;
- info->step_chunk_size = 0;
- info->step_spare_size = 0;
- info->cur_chunk = 0;
- info->use_ecc = 0;
- info->use_spare = 1;
- info->retcode = ERR_NONE;
- info->ecc_err_cnt = 0;
- info->ndcb3 = 0;
- info->need_wait = 0;
-
- switch (command) {
- case NAND_CMD_READ0:
- case NAND_CMD_PAGEPROG:
- info->use_ecc = 1;
- break;
- case NAND_CMD_PARAM:
- info->use_spare = 0;
- break;
- default:
- info->ndcb1 = 0;
- info->ndcb2 = 0;
- break;
- }
-
- /*
- * If we are about to issue a read command, or about to set
- * the write address, then clean the data buffer.
- */
- if (command == NAND_CMD_READ0 ||
- command == NAND_CMD_READOOB ||
- command == NAND_CMD_SEQIN) {
-
- info->buf_count = mtd->writesize + mtd->oobsize;
- memset(info->data_buff, 0xFF, info->buf_count);
- }
-
-}
-
-static int prepare_set_command(struct pxa3xx_nand_info *info, int command,
- int ext_cmd_type, uint16_t column, int page_addr)
-{
- int addr_cycle, exec_cmd;
- struct pxa3xx_nand_host *host;
- struct mtd_info *mtd;
-
- host = info->host[info->cs];
- mtd = nand_to_mtd(&host->chip);
- addr_cycle = 0;
- exec_cmd = 1;
-
- if (info->cs != 0)
- info->ndcb0 = NDCB0_CSEL;
- else
- info->ndcb0 = 0;
-
- if (command == NAND_CMD_SEQIN)
- exec_cmd = 0;
-
- addr_cycle = NDCB0_ADDR_CYC(host->row_addr_cycles
- + host->col_addr_cycles);
-
- switch (command) {
- case NAND_CMD_READOOB:
- case NAND_CMD_READ0:
- info->buf_start = column;
- info->ndcb0 |= NDCB0_CMD_TYPE(0)
- | addr_cycle
- | NAND_CMD_READ0;
-
- if (command == NAND_CMD_READOOB)
- info->buf_start += mtd->writesize;
-
- if (info->cur_chunk < info->nfullchunks) {
- info->step_chunk_size = info->chunk_size;
- info->step_spare_size = info->spare_size;
- } else {
- info->step_chunk_size = info->last_chunk_size;
- info->step_spare_size = info->last_spare_size;
- }
-
- /*
- * Multiple page read needs an 'extended command type' field,
- * which is either naked-read or last-read according to the
- * state.
- */
- if (mtd->writesize == PAGE_CHUNK_SIZE) {
- info->ndcb0 |= NDCB0_DBC | (NAND_CMD_READSTART << 8);
- } else if (mtd->writesize > PAGE_CHUNK_SIZE) {
- info->ndcb0 |= NDCB0_DBC | (NAND_CMD_READSTART << 8)
- | NDCB0_LEN_OVRD
- | NDCB0_EXT_CMD_TYPE(ext_cmd_type);
- info->ndcb3 = info->step_chunk_size +
- info->step_spare_size;
- }
-
- set_command_address(info, mtd->writesize, column, page_addr);
- break;
-
- case NAND_CMD_SEQIN:
-
- info->buf_start = column;
- set_command_address(info, mtd->writesize, 0, page_addr);
-
- /*
- * Multiple page programming needs to execute the initial
- * SEQIN command that sets the page address.
- */
- if (mtd->writesize > PAGE_CHUNK_SIZE) {
- info->ndcb0 |= NDCB0_CMD_TYPE(0x1)
- | NDCB0_EXT_CMD_TYPE(ext_cmd_type)
- | addr_cycle
- | command;
- exec_cmd = 1;
- }
- break;
-
- case NAND_CMD_PAGEPROG:
- if (is_buf_blank(info->data_buff,
- (mtd->writesize + mtd->oobsize))) {
- exec_cmd = 0;
- break;
- }
-
- if (info->cur_chunk < info->nfullchunks) {
- info->step_chunk_size = info->chunk_size;
- info->step_spare_size = info->spare_size;
- } else {
- info->step_chunk_size = info->last_chunk_size;
- info->step_spare_size = info->last_spare_size;
- }
-
- /* Second command setting for large pages */
- if (mtd->writesize > PAGE_CHUNK_SIZE) {
- /*
- * Multiple page write uses the 'extended command'
- * field. This can be used to issue a command dispatch
- * or a naked-write depending on the current stage.
- */
- info->ndcb0 |= NDCB0_CMD_TYPE(0x1)
- | NDCB0_LEN_OVRD
- | NDCB0_EXT_CMD_TYPE(ext_cmd_type);
- info->ndcb3 = info->step_chunk_size +
- info->step_spare_size;
-
- /*
- * This is the command dispatch that completes a chunked
- * page program operation.
- */
- if (info->cur_chunk == info->ntotalchunks) {
- info->ndcb0 = NDCB0_CMD_TYPE(0x1)
- | NDCB0_EXT_CMD_TYPE(ext_cmd_type)
- | command;
- info->ndcb1 = 0;
- info->ndcb2 = 0;
- info->ndcb3 = 0;
- }
- } else {
- info->ndcb0 |= NDCB0_CMD_TYPE(0x1)
- | NDCB0_AUTO_RS
- | NDCB0_ST_ROW_EN
- | NDCB0_DBC
- | (NAND_CMD_PAGEPROG << 8)
- | NAND_CMD_SEQIN
- | addr_cycle;
- }
- break;
-
- case NAND_CMD_PARAM:
- info->buf_count = INIT_BUFFER_SIZE;
- info->ndcb0 |= NDCB0_CMD_TYPE(0)
- | NDCB0_ADDR_CYC(1)
- | NDCB0_LEN_OVRD
- | command;
- info->ndcb1 = (column & 0xFF);
- info->ndcb3 = INIT_BUFFER_SIZE;
- info->step_chunk_size = INIT_BUFFER_SIZE;
- break;
-
- case NAND_CMD_READID:
- info->buf_count = READ_ID_BYTES;
- info->ndcb0 |= NDCB0_CMD_TYPE(3)
- | NDCB0_ADDR_CYC(1)
- | command;
- info->ndcb1 = (column & 0xFF);
-
- info->step_chunk_size = 8;
- break;
- case NAND_CMD_STATUS:
- info->buf_count = 1;
- info->ndcb0 |= NDCB0_CMD_TYPE(4)
- | NDCB0_ADDR_CYC(1)
- | command;
-
- info->step_chunk_size = 8;
- break;
-
- case NAND_CMD_ERASE1:
- info->ndcb0 |= NDCB0_CMD_TYPE(2)
- | NDCB0_AUTO_RS
- | NDCB0_ADDR_CYC(3)
- | NDCB0_DBC
- | (NAND_CMD_ERASE2 << 8)
- | NAND_CMD_ERASE1;
- info->ndcb1 = page_addr;
- info->ndcb2 = 0;
-
- break;
- case NAND_CMD_RESET:
- info->ndcb0 |= NDCB0_CMD_TYPE(5)
- | command;
-
- break;
-
- case NAND_CMD_ERASE2:
- exec_cmd = 0;
- break;
-
- default:
- exec_cmd = 0;
- dev_err(&info->pdev->dev, "non-supported command %x\n",
- command);
- break;
- }
-
- return exec_cmd;
-}
-
-static void nand_cmdfunc(struct mtd_info *mtd, unsigned command,
- int column, int page_addr)
-{
- struct nand_chip *chip = mtd_to_nand(mtd);
- struct pxa3xx_nand_host *host = nand_get_controller_data(chip);
- struct pxa3xx_nand_info *info = host->info_data;
- int exec_cmd;
-
- /*
- * if this is a x16 device ,then convert the input
- * "byte" address into a "word" address appropriate
- * for indexing a word-oriented device
- */
- if (info->reg_ndcr & NDCR_DWIDTH_M)
- column /= 2;
-
- /*
- * There may be different NAND chip hooked to
- * different chip select, so check whether
- * chip select has been changed, if yes, reset the timing
- */
- if (info->cs != host->cs) {
- info->cs = host->cs;
- nand_writel(info, NDTR0CS0, info->ndtr0cs0);
- nand_writel(info, NDTR1CS0, info->ndtr1cs0);
- }
-
- prepare_start_command(info, command);
-
- info->state = STATE_PREPARED;
- exec_cmd = prepare_set_command(info, command, 0, column, page_addr);
-
- if (exec_cmd) {
- init_completion(&info->cmd_complete);
- init_completion(&info->dev_ready);
- info->need_wait = 1;
- pxa3xx_nand_start(info);
-
- if (!wait_for_completion_timeout(&info->cmd_complete,
- CHIP_DELAY_TIMEOUT)) {
- dev_err(&info->pdev->dev, "Wait time out!!!\n");
- /* Stop State Machine for next command cycle */
- pxa3xx_nand_stop(info);
- }
- }
- info->state = STATE_IDLE;
-}
-
-static void nand_cmdfunc_extended(struct mtd_info *mtd,
- const unsigned command,
- int column, int page_addr)
-{
- struct nand_chip *chip = mtd_to_nand(mtd);
- struct pxa3xx_nand_host *host = nand_get_controller_data(chip);
- struct pxa3xx_nand_info *info = host->info_data;
- int exec_cmd, ext_cmd_type;
-
- /*
- * if this is a x16 device then convert the input
- * "byte" address into a "word" address appropriate
- * for indexing a word-oriented device
- */
- if (info->reg_ndcr & NDCR_DWIDTH_M)
- column /= 2;
-
- /*
- * There may be different NAND chip hooked to
- * different chip select, so check whether
- * chip select has been changed, if yes, reset the timing
- */
- if (info->cs != host->cs) {
- info->cs = host->cs;
- nand_writel(info, NDTR0CS0, info->ndtr0cs0);
- nand_writel(info, NDTR1CS0, info->ndtr1cs0);
- }
-
- /* Select the extended command for the first command */
- switch (command) {
- case NAND_CMD_READ0:
- case NAND_CMD_READOOB:
- ext_cmd_type = EXT_CMD_TYPE_MONO;
- break;
- case NAND_CMD_SEQIN:
- ext_cmd_type = EXT_CMD_TYPE_DISPATCH;
- break;
- case NAND_CMD_PAGEPROG:
- ext_cmd_type = EXT_CMD_TYPE_NAKED_RW;
- break;
- default:
- ext_cmd_type = 0;
- break;
- }
-
- prepare_start_command(info, command);
-
- /*
- * Prepare the "is ready" completion before starting a command
- * transaction sequence. If the command is not executed the
- * completion will be completed, see below.
- *
- * We can do that inside the loop because the command variable
- * is invariant and thus so is the exec_cmd.
- */
- info->need_wait = 1;
- init_completion(&info->dev_ready);
- do {
- info->state = STATE_PREPARED;
-
- exec_cmd = prepare_set_command(info, command, ext_cmd_type,
- column, page_addr);
- if (!exec_cmd) {
- info->need_wait = 0;
- complete(&info->dev_ready);
- break;
- }
-
- init_completion(&info->cmd_complete);
- pxa3xx_nand_start(info);
-
- if (!wait_for_completion_timeout(&info->cmd_complete,
- CHIP_DELAY_TIMEOUT)) {
- dev_err(&info->pdev->dev, "Wait time out!!!\n");
- /* Stop State Machine for next command cycle */
- pxa3xx_nand_stop(info);
- break;
- }
-
- /* Only a few commands need several steps */
- if (command != NAND_CMD_PAGEPROG &&
- command != NAND_CMD_READ0 &&
- command != NAND_CMD_READOOB)
- break;
-
- info->cur_chunk++;
-
- /* Check if the sequence is complete */
- if (info->cur_chunk == info->ntotalchunks && command != NAND_CMD_PAGEPROG)
- break;
-
- /*
- * After a splitted program command sequence has issued
- * the command dispatch, the command sequence is complete.
- */
- if (info->cur_chunk == (info->ntotalchunks + 1) &&
- command == NAND_CMD_PAGEPROG &&
- ext_cmd_type == EXT_CMD_TYPE_DISPATCH)
- break;
-
- if (command == NAND_CMD_READ0 || command == NAND_CMD_READOOB) {
- /* Last read: issue a 'last naked read' */
- if (info->cur_chunk == info->ntotalchunks - 1)
- ext_cmd_type = EXT_CMD_TYPE_LAST_RW;
- else
- ext_cmd_type = EXT_CMD_TYPE_NAKED_RW;
-
- /*
- * If a splitted program command has no more data to transfer,
- * the command dispatch must be issued to complete.
- */
- } else if (command == NAND_CMD_PAGEPROG &&
- info->cur_chunk == info->ntotalchunks) {
- ext_cmd_type = EXT_CMD_TYPE_DISPATCH;
- }
- } while (1);
-
- info->state = STATE_IDLE;
-}
-
-static int pxa3xx_nand_write_page_hwecc(struct mtd_info *mtd,
- struct nand_chip *chip, const uint8_t *buf, int oob_required,
- int page)
-{
- nand_prog_page_begin_op(chip, page, 0, buf, mtd->writesize);
- chip->write_buf(mtd, chip->oob_poi, mtd->oobsize);
-
- return nand_prog_page_end_op(chip);
-}
-
-static int pxa3xx_nand_read_page_hwecc(struct mtd_info *mtd,
- struct nand_chip *chip, uint8_t *buf, int oob_required,
- int page)
-{
- struct pxa3xx_nand_host *host = nand_get_controller_data(chip);
- struct pxa3xx_nand_info *info = host->info_data;
-
- nand_read_page_op(chip, page, 0, buf, mtd->writesize);
- chip->read_buf(mtd, chip->oob_poi, mtd->oobsize);
-
- if (info->retcode == ERR_CORERR && info->use_ecc) {
- mtd->ecc_stats.corrected += info->ecc_err_cnt;
-
- } else if (info->retcode == ERR_UNCORERR) {
- /*
- * for blank page (all 0xff), HW will calculate its ECC as
- * 0, which is different from the ECC information within
- * OOB, ignore such uncorrectable errors
- */
- if (is_buf_blank(buf, mtd->writesize))
- info->retcode = ERR_NONE;
- else
- mtd->ecc_stats.failed++;
- }
-
- return info->max_bitflips;
-}
-
-static uint8_t pxa3xx_nand_read_byte(struct mtd_info *mtd)
-{
- struct nand_chip *chip = mtd_to_nand(mtd);
- struct pxa3xx_nand_host *host = nand_get_controller_data(chip);
- struct pxa3xx_nand_info *info = host->info_data;
- char retval = 0xFF;
-
- if (info->buf_start < info->buf_count)
- /* Has just send a new command? */
- retval = info->data_buff[info->buf_start++];
-
- return retval;
-}
-
-static u16 pxa3xx_nand_read_word(struct mtd_info *mtd)
-{
- struct nand_chip *chip = mtd_to_nand(mtd);
- struct pxa3xx_nand_host *host = nand_get_controller_data(chip);
- struct pxa3xx_nand_info *info = host->info_data;
- u16 retval = 0xFFFF;
-
- if (!(info->buf_start & 0x01) && info->buf_start < info->buf_count) {
- retval = *((u16 *)(info->data_buff+info->buf_start));
- info->buf_start += 2;
- }
- return retval;
-}
-
-static void pxa3xx_nand_read_buf(struct mtd_info *mtd, uint8_t *buf, int len)
-{
- struct nand_chip *chip = mtd_to_nand(mtd);
- struct pxa3xx_nand_host *host = nand_get_controller_data(chip);
- struct pxa3xx_nand_info *info = host->info_data;
- int real_len = min_t(size_t, len, info->buf_count - info->buf_start);
-
- memcpy(buf, info->data_buff + info->buf_start, real_len);
- info->buf_start += real_len;
-}
-
-static void pxa3xx_nand_write_buf(struct mtd_info *mtd,
- const uint8_t *buf, int len)
-{
- struct nand_chip *chip = mtd_to_nand(mtd);
- struct pxa3xx_nand_host *host = nand_get_controller_data(chip);
- struct pxa3xx_nand_info *info = host->info_data;
- int real_len = min_t(size_t, len, info->buf_count - info->buf_start);
-
- memcpy(info->data_buff + info->buf_start, buf, real_len);
- info->buf_start += real_len;
-}
-
-static void pxa3xx_nand_select_chip(struct mtd_info *mtd, int chip)
-{
- return;
-}
-
-static int pxa3xx_nand_waitfunc(struct mtd_info *mtd, struct nand_chip *this)
-{
- struct nand_chip *chip = mtd_to_nand(mtd);
- struct pxa3xx_nand_host *host = nand_get_controller_data(chip);
- struct pxa3xx_nand_info *info = host->info_data;
-
- if (info->need_wait) {
- info->need_wait = 0;
- if (!wait_for_completion_timeout(&info->dev_ready,
- CHIP_DELAY_TIMEOUT)) {
- dev_err(&info->pdev->dev, "Ready time out!!!\n");
- return NAND_STATUS_FAIL;
- }
- }
-
- /* pxa3xx_nand_send_command has waited for command complete */
- if (this->state == FL_WRITING || this->state == FL_ERASING) {
- if (info->retcode == ERR_NONE)
- return 0;
- else
- return NAND_STATUS_FAIL;
- }
-
- return NAND_STATUS_READY;
-}
-
-static int pxa3xx_nand_config_ident(struct pxa3xx_nand_info *info)
-{
- struct pxa3xx_nand_host *host = info->host[info->cs];
- struct platform_device *pdev = info->pdev;
- struct pxa3xx_nand_platform_data *pdata = dev_get_platdata(&pdev->dev);
- const struct nand_sdr_timings *timings;
-
- /* Configure default flash values */
- info->chunk_size = PAGE_CHUNK_SIZE;
- info->reg_ndcr = 0x0; /* enable all interrupts */
- info->reg_ndcr |= (pdata->enable_arbiter) ? NDCR_ND_ARB_EN : 0;
- info->reg_ndcr |= NDCR_RD_ID_CNT(READ_ID_BYTES);
- info->reg_ndcr |= NDCR_SPARE_EN;
-
- /* use the common timing to make a try */
- timings = onfi_async_timing_mode_to_sdr_timings(0);
- if (IS_ERR(timings))
- return PTR_ERR(timings);
-
- pxa3xx_nand_set_sdr_timing(host, timings);
- return 0;
-}
-
-static void pxa3xx_nand_config_tail(struct pxa3xx_nand_info *info)
-{
- struct pxa3xx_nand_host *host = info->host[info->cs];
- struct nand_chip *chip = &host->chip;
- struct mtd_info *mtd = nand_to_mtd(chip);
-
- info->reg_ndcr |= (host->col_addr_cycles == 2) ? NDCR_RA_START : 0;
- info->reg_ndcr |= (chip->page_shift == 6) ? NDCR_PG_PER_BLK : 0;
- info->reg_ndcr |= (mtd->writesize == 2048) ? NDCR_PAGE_SZ : 0;
-}
-
-static void pxa3xx_nand_detect_config(struct pxa3xx_nand_info *info)
-{
- struct platform_device *pdev = info->pdev;
- struct pxa3xx_nand_platform_data *pdata = dev_get_platdata(&pdev->dev);
- uint32_t ndcr = nand_readl(info, NDCR);
-
- /* Set an initial chunk size */
- info->chunk_size = ndcr & NDCR_PAGE_SZ ? 2048 : 512;
- info->reg_ndcr = ndcr &
- ~(NDCR_INT_MASK | NDCR_ND_ARB_EN | NFCV1_NDCR_ARB_CNTL);
- info->reg_ndcr |= (pdata->enable_arbiter) ? NDCR_ND_ARB_EN : 0;
- info->ndtr0cs0 = nand_readl(info, NDTR0CS0);
- info->ndtr1cs0 = nand_readl(info, NDTR1CS0);
-}
-
-static int pxa3xx_nand_init_buff(struct pxa3xx_nand_info *info)
-{
- struct platform_device *pdev = info->pdev;
- struct dma_slave_config config;
- dma_cap_mask_t mask;
- struct pxad_param param;
- int ret;
-
- info->data_buff = kmalloc(info->buf_size, GFP_KERNEL);
- if (info->data_buff == NULL)
- return -ENOMEM;
- if (use_dma == 0)
- return 0;
-
- ret = dma_set_mask_and_coherent(&pdev->dev, DMA_BIT_MASK(32));
- if (ret)
- return ret;
-
- sg_init_one(&info->sg, info->data_buff, info->buf_size);
- dma_cap_zero(mask);
- dma_cap_set(DMA_SLAVE, mask);
- param.prio = PXAD_PRIO_LOWEST;
- param.drcmr = info->drcmr_dat;
- info->dma_chan = dma_request_slave_channel_compat(mask, pxad_filter_fn,
- ¶m, &pdev->dev,
- "data");
- if (!info->dma_chan) {
- dev_err(&pdev->dev, "unable to request data dma channel\n");
- return -ENODEV;
- }
-
- memset(&config, 0, sizeof(config));
- config.src_addr_width = DMA_SLAVE_BUSWIDTH_4_BYTES;
- config.dst_addr_width = DMA_SLAVE_BUSWIDTH_4_BYTES;
- config.src_addr = info->mmio_phys + NDDB;
- config.dst_addr = info->mmio_phys + NDDB;
- config.src_maxburst = 32;
- config.dst_maxburst = 32;
- ret = dmaengine_slave_config(info->dma_chan, &config);
- if (ret < 0) {
- dev_err(&info->pdev->dev,
- "dma channel configuration failed: %d\n",
- ret);
- return ret;
- }
-
- /*
- * Now that DMA buffers are allocated we turn on
- * DMA proper for I/O operations.
- */
- info->use_dma = 1;
- return 0;
-}
-
-static void pxa3xx_nand_free_buff(struct pxa3xx_nand_info *info)
-{
- if (info->use_dma) {
- dmaengine_terminate_all(info->dma_chan);
- dma_release_channel(info->dma_chan);
- }
- kfree(info->data_buff);
-}
-
-static int pxa_ecc_init(struct pxa3xx_nand_info *info,
- struct mtd_info *mtd,
- int strength, int ecc_stepsize, int page_size)
-{
- struct nand_chip *chip = mtd_to_nand(mtd);
- struct nand_ecc_ctrl *ecc = &chip->ecc;
-
- if (strength == 1 && ecc_stepsize == 512 && page_size == 2048) {
- info->nfullchunks = 1;
- info->ntotalchunks = 1;
- info->chunk_size = 2048;
- info->spare_size = 40;
- info->ecc_size = 24;
- ecc->mode = NAND_ECC_HW;
- ecc->size = 512;
- ecc->strength = 1;
-
- } else if (strength == 1 && ecc_stepsize == 512 && page_size == 512) {
- info->nfullchunks = 1;
- info->ntotalchunks = 1;
- info->chunk_size = 512;
- info->spare_size = 8;
- info->ecc_size = 8;
- ecc->mode = NAND_ECC_HW;
- ecc->size = 512;
- ecc->strength = 1;
-
- /*
- * Required ECC: 4-bit correction per 512 bytes
- * Select: 16-bit correction per 2048 bytes
- */
- } else if (strength == 4 && ecc_stepsize == 512 && page_size == 2048) {
- info->ecc_bch = 1;
- info->nfullchunks = 1;
- info->ntotalchunks = 1;
- info->chunk_size = 2048;
- info->spare_size = 32;
- info->ecc_size = 32;
- ecc->mode = NAND_ECC_HW;
- ecc->size = info->chunk_size;
- mtd_set_ooblayout(mtd, &pxa3xx_ooblayout_ops);
- ecc->strength = 16;
-
- } else if (strength == 4 && ecc_stepsize == 512 && page_size == 4096) {
- info->ecc_bch = 1;
- info->nfullchunks = 2;
- info->ntotalchunks = 2;
- info->chunk_size = 2048;
- info->spare_size = 32;
- info->ecc_size = 32;
- ecc->mode = NAND_ECC_HW;
- ecc->size = info->chunk_size;
- mtd_set_ooblayout(mtd, &pxa3xx_ooblayout_ops);
- ecc->strength = 16;
-
- /*
- * Required ECC: 8-bit correction per 512 bytes
- * Select: 16-bit correction per 1024 bytes
- */
- } else if (strength == 8 && ecc_stepsize == 512 && page_size == 4096) {
- info->ecc_bch = 1;
- info->nfullchunks = 4;
- info->ntotalchunks = 5;
- info->chunk_size = 1024;
- info->spare_size = 0;
- info->last_chunk_size = 0;
- info->last_spare_size = 64;
- info->ecc_size = 32;
- ecc->mode = NAND_ECC_HW;
- ecc->size = info->chunk_size;
- mtd_set_ooblayout(mtd, &pxa3xx_ooblayout_ops);
- ecc->strength = 16;
- } else {
- dev_err(&info->pdev->dev,
- "ECC strength %d at page size %d is not supported\n",
- strength, page_size);
- return -ENODEV;
- }
-
- dev_info(&info->pdev->dev, "ECC strength %d, ECC step size %d\n",
- ecc->strength, ecc->size);
- return 0;
-}
-
-static int pxa3xx_nand_scan(struct mtd_info *mtd)
-{
- struct nand_chip *chip = mtd_to_nand(mtd);
- struct pxa3xx_nand_host *host = nand_get_controller_data(chip);
- struct pxa3xx_nand_info *info = host->info_data;
- struct platform_device *pdev = info->pdev;
- struct pxa3xx_nand_platform_data *pdata = dev_get_platdata(&pdev->dev);
- int ret;
- uint16_t ecc_strength, ecc_step;
-
- if (pdata->keep_config) {
- pxa3xx_nand_detect_config(info);
- } else {
- ret = pxa3xx_nand_config_ident(info);
- if (ret)
- return ret;
- }
-
- if (info->reg_ndcr & NDCR_DWIDTH_M)
- chip->options |= NAND_BUSWIDTH_16;
-
- /* Device detection must be done with ECC disabled */
- if (info->variant == PXA3XX_NAND_VARIANT_ARMADA370 ||
- info->variant == PXA3XX_NAND_VARIANT_ARMADA_8K)
- nand_writel(info, NDECCCTRL, 0x0);
-
- if (pdata->flash_bbt)
- chip->bbt_options |= NAND_BBT_USE_FLASH;
-
- chip->ecc.strength = pdata->ecc_strength;
- chip->ecc.size = pdata->ecc_step_size;
-
- ret = nand_scan_ident(mtd, 1, NULL);
- if (ret)
- return ret;
-
- if (!pdata->keep_config) {
- ret = pxa3xx_nand_init(host);
- if (ret) {
- dev_err(&info->pdev->dev, "Failed to init nand: %d\n",
- ret);
- return ret;
- }
- }
-
- if (chip->bbt_options & NAND_BBT_USE_FLASH) {
- /*
- * We'll use a bad block table stored in-flash and don't
- * allow writing the bad block marker to the flash.
- */
- chip->bbt_options |= NAND_BBT_NO_OOB_BBM;
- chip->bbt_td = &bbt_main_descr;
- chip->bbt_md = &bbt_mirror_descr;
- }
-
- /*
- * If the page size is bigger than the FIFO size, let's check
- * we are given the right variant and then switch to the extended
- * (aka splitted) command handling,
- */
- if (mtd->writesize > PAGE_CHUNK_SIZE) {
- if (info->variant == PXA3XX_NAND_VARIANT_ARMADA370 ||
- info->variant == PXA3XX_NAND_VARIANT_ARMADA_8K) {
- chip->cmdfunc = nand_cmdfunc_extended;
- } else {
- dev_err(&info->pdev->dev,
- "unsupported page size on this variant\n");
- return -ENODEV;
- }
- }
-
- ecc_strength = chip->ecc.strength;
- ecc_step = chip->ecc.size;
- if (!ecc_strength || !ecc_step) {
- ecc_strength = chip->ecc_strength_ds;
- ecc_step = chip->ecc_step_ds;
- }
-
- /* Set default ECC strength requirements on non-ONFI devices */
- if (ecc_strength < 1 && ecc_step < 1) {
- ecc_strength = 1;
- ecc_step = 512;
- }
-
- ret = pxa_ecc_init(info, mtd, ecc_strength,
- ecc_step, mtd->writesize);
- if (ret)
- return ret;
-
- /* calculate addressing information */
- if (mtd->writesize >= 2048)
- host->col_addr_cycles = 2;
- else
- host->col_addr_cycles = 1;
-
- /* release the initial buffer */
- kfree(info->data_buff);
-
- /* allocate the real data + oob buffer */
- info->buf_size = mtd->writesize + mtd->oobsize;
- ret = pxa3xx_nand_init_buff(info);
- if (ret)
- return ret;
- info->oob_buff = info->data_buff + mtd->writesize;
-
- if ((mtd->size >> chip->page_shift) > 65536)
- host->row_addr_cycles = 3;
- else
- host->row_addr_cycles = 2;
-
- if (!pdata->keep_config)
- pxa3xx_nand_config_tail(info);
-
- return nand_scan_tail(mtd);
-}
-
-static int alloc_nand_resource(struct platform_device *pdev)
-{
- struct device_node *np = pdev->dev.of_node;
- struct pxa3xx_nand_platform_data *pdata;
- struct pxa3xx_nand_info *info;
- struct pxa3xx_nand_host *host;
- struct nand_chip *chip = NULL;
- struct mtd_info *mtd;
- struct resource *r;
- int ret, irq, cs;
-
- pdata = dev_get_platdata(&pdev->dev);
- if (pdata->num_cs <= 0) {
- dev_err(&pdev->dev, "invalid number of chip selects\n");
- return -ENODEV;
- }
-
- info = devm_kzalloc(&pdev->dev,
- sizeof(*info) + sizeof(*host) * pdata->num_cs,
- GFP_KERNEL);
- if (!info)
- return -ENOMEM;
-
- info->pdev = pdev;
- info->variant = pxa3xx_nand_get_variant(pdev);
- for (cs = 0; cs < pdata->num_cs; cs++) {
- host = (void *)&info[1] + sizeof(*host) * cs;
- chip = &host->chip;
- nand_set_controller_data(chip, host);
- mtd = nand_to_mtd(chip);
- info->host[cs] = host;
- host->cs = cs;
- host->info_data = info;
- mtd->dev.parent = &pdev->dev;
- /* FIXME: all chips use the same device tree partitions */
- nand_set_flash_node(chip, np);
-
- nand_set_controller_data(chip, host);
- chip->ecc.read_page = pxa3xx_nand_read_page_hwecc;
- chip->ecc.write_page = pxa3xx_nand_write_page_hwecc;
- chip->controller = &info->controller;
- chip->waitfunc = pxa3xx_nand_waitfunc;
- chip->select_chip = pxa3xx_nand_select_chip;
- chip->read_word = pxa3xx_nand_read_word;
- chip->read_byte = pxa3xx_nand_read_byte;
- chip->read_buf = pxa3xx_nand_read_buf;
- chip->write_buf = pxa3xx_nand_write_buf;
- chip->options |= NAND_NO_SUBPAGE_WRITE;
- chip->cmdfunc = nand_cmdfunc;
- chip->onfi_set_features = nand_onfi_get_set_features_notsupp;
- chip->onfi_get_features = nand_onfi_get_set_features_notsupp;
- }
-
- nand_hw_control_init(chip->controller);
- info->clk = devm_clk_get(&pdev->dev, NULL);
- if (IS_ERR(info->clk)) {
- ret = PTR_ERR(info->clk);
- dev_err(&pdev->dev, "failed to get nand clock: %d\n", ret);
- return ret;
- }
- ret = clk_prepare_enable(info->clk);
- if (ret < 0)
- return ret;
-
- if (!np && use_dma) {
- r = platform_get_resource(pdev, IORESOURCE_DMA, 0);
- if (r == NULL) {
- dev_err(&pdev->dev,
- "no resource defined for data DMA\n");
- ret = -ENXIO;
- goto fail_disable_clk;
- }
- info->drcmr_dat = r->start;
- }
-
- irq = platform_get_irq(pdev, 0);
- if (irq < 0) {
- dev_err(&pdev->dev, "no IRQ resource defined\n");
- ret = -ENXIO;
- goto fail_disable_clk;
- }
-
- r = platform_get_resource(pdev, IORESOURCE_MEM, 0);
- info->mmio_base = devm_ioremap_resource(&pdev->dev, r);
- if (IS_ERR(info->mmio_base)) {
- ret = PTR_ERR(info->mmio_base);
- dev_err(&pdev->dev, "failed to map register space: %d\n", ret);
- goto fail_disable_clk;
- }
- info->mmio_phys = r->start;
-
- /* Allocate a buffer to allow flash detection */
- info->buf_size = INIT_BUFFER_SIZE;
- info->data_buff = kmalloc(info->buf_size, GFP_KERNEL);
- if (info->data_buff == NULL) {
- ret = -ENOMEM;
- goto fail_disable_clk;
- }
-
- /* initialize all interrupts to be disabled */
- disable_int(info, NDSR_MASK);
-
- ret = request_threaded_irq(irq, pxa3xx_nand_irq,
- pxa3xx_nand_irq_thread, IRQF_ONESHOT,
- pdev->name, info);
- if (ret < 0) {
- dev_err(&pdev->dev, "failed to request IRQ: %d\n", ret);
- goto fail_free_buf;
- }
-
- platform_set_drvdata(pdev, info);
-
- return 0;
-
-fail_free_buf:
- free_irq(irq, info);
- kfree(info->data_buff);
-fail_disable_clk:
- clk_disable_unprepare(info->clk);
- return ret;
-}
-
-static int pxa3xx_nand_remove(struct platform_device *pdev)
-{
- struct pxa3xx_nand_info *info = platform_get_drvdata(pdev);
- struct pxa3xx_nand_platform_data *pdata;
- int irq, cs;
-
- if (!info)
- return 0;
-
- pdata = dev_get_platdata(&pdev->dev);
-
- irq = platform_get_irq(pdev, 0);
- if (irq >= 0)
- free_irq(irq, info);
- pxa3xx_nand_free_buff(info);
-
- /*
- * In the pxa3xx case, the DFI bus is shared between the SMC and NFC.
- * In order to prevent a lockup of the system bus, the DFI bus
- * arbitration is granted to SMC upon driver removal. This is done by
- * setting the x_ARB_CNTL bit, which also prevents the NAND to have
- * access to the bus anymore.
- */
- nand_writel(info, NDCR,
- (nand_readl(info, NDCR) & ~NDCR_ND_ARB_EN) |
- NFCV1_NDCR_ARB_CNTL);
- clk_disable_unprepare(info->clk);
-
- for (cs = 0; cs < pdata->num_cs; cs++)
- nand_release(nand_to_mtd(&info->host[cs]->chip));
- return 0;
-}
-
-static int pxa3xx_nand_probe_dt(struct platform_device *pdev)
-{
- struct pxa3xx_nand_platform_data *pdata;
- struct device_node *np = pdev->dev.of_node;
- const struct of_device_id *of_id =
- of_match_device(pxa3xx_nand_dt_ids, &pdev->dev);
-
- if (!of_id)
- return 0;
-
- /*
- * Some SoCs like A7k/A8k need to enable manually the NAND
- * controller to avoid being bootloader dependent. This is done
- * through the use of a single bit in the System Functions registers.
- */
- if (pxa3xx_nand_get_variant(pdev) == PXA3XX_NAND_VARIANT_ARMADA_8K) {
- struct regmap *sysctrl_base = syscon_regmap_lookup_by_phandle(
- pdev->dev.of_node, "marvell,system-controller");
- u32 reg;
-
- if (IS_ERR(sysctrl_base))
- return PTR_ERR(sysctrl_base);
-
- regmap_read(sysctrl_base, GENCONF_SOC_DEVICE_MUX, ®);
- reg |= GENCONF_SOC_DEVICE_MUX_NFC_EN;
- regmap_write(sysctrl_base, GENCONF_SOC_DEVICE_MUX, reg);
- }
-
- pdata = devm_kzalloc(&pdev->dev, sizeof(*pdata), GFP_KERNEL);
- if (!pdata)
- return -ENOMEM;
-
- if (of_get_property(np, "marvell,nand-enable-arbiter", NULL))
- pdata->enable_arbiter = 1;
- if (of_get_property(np, "marvell,nand-keep-config", NULL))
- pdata->keep_config = 1;
- of_property_read_u32(np, "num-cs", &pdata->num_cs);
-
- pdev->dev.platform_data = pdata;
-
- return 0;
-}
-
-static int pxa3xx_nand_probe(struct platform_device *pdev)
-{
- struct pxa3xx_nand_platform_data *pdata;
- struct pxa3xx_nand_info *info;
- int ret, cs, probe_success, dma_available;
-
- dma_available = IS_ENABLED(CONFIG_ARM) &&
- (IS_ENABLED(CONFIG_ARCH_PXA) || IS_ENABLED(CONFIG_ARCH_MMP));
- if (use_dma && !dma_available) {
- use_dma = 0;
- dev_warn(&pdev->dev,
- "This platform can't do DMA on this device\n");
- }
-
- ret = pxa3xx_nand_probe_dt(pdev);
- if (ret)
- return ret;
-
- pdata = dev_get_platdata(&pdev->dev);
- if (!pdata) {
- dev_err(&pdev->dev, "no platform data defined\n");
- return -ENODEV;
- }
-
- ret = alloc_nand_resource(pdev);
- if (ret)
- return ret;
-
- info = platform_get_drvdata(pdev);
- probe_success = 0;
- for (cs = 0; cs < pdata->num_cs; cs++) {
- struct mtd_info *mtd = nand_to_mtd(&info->host[cs]->chip);
-
- /*
- * The mtd name matches the one used in 'mtdparts' kernel
- * parameter. This name cannot be changed or otherwise
- * user's mtd partitions configuration would get broken.
- */
- mtd->name = "pxa3xx_nand-0";
- info->cs = cs;
- ret = pxa3xx_nand_scan(mtd);
- if (ret) {
- dev_warn(&pdev->dev, "failed to scan nand at cs %d\n",
- cs);
- continue;
- }
-
- ret = mtd_device_register(mtd, pdata->parts[cs],
- pdata->nr_parts[cs]);
- if (!ret)
- probe_success = 1;
- }
-
- if (!probe_success) {
- pxa3xx_nand_remove(pdev);
- return -ENODEV;
- }
-
- return 0;
-}
-
-#ifdef CONFIG_PM
-static int pxa3xx_nand_suspend(struct device *dev)
-{
- struct pxa3xx_nand_info *info = dev_get_drvdata(dev);
-
- if (info->state) {
- dev_err(dev, "driver busy, state = %d\n", info->state);
- return -EAGAIN;
- }
-
- clk_disable(info->clk);
- return 0;
-}
-
-static int pxa3xx_nand_resume(struct device *dev)
-{
- struct pxa3xx_nand_info *info = dev_get_drvdata(dev);
- int ret;
-
- ret = clk_enable(info->clk);
- if (ret < 0)
- return ret;
-
- /* We don't want to handle interrupt without calling mtd routine */
- disable_int(info, NDCR_INT_MASK);
-
- /*
- * Directly set the chip select to a invalid value,
- * then the driver would reset the timing according
- * to current chip select at the beginning of cmdfunc
- */
- info->cs = 0xff;
-
- /*
- * As the spec says, the NDSR would be updated to 0x1800 when
- * doing the nand_clk disable/enable.
- * To prevent it damaging state machine of the driver, clear
- * all status before resume
- */
- nand_writel(info, NDSR, NDSR_MASK);
-
- return 0;
-}
-#else
-#define pxa3xx_nand_suspend NULL
-#define pxa3xx_nand_resume NULL
-#endif
-
-static const struct dev_pm_ops pxa3xx_nand_pm_ops = {
- .suspend = pxa3xx_nand_suspend,
- .resume = pxa3xx_nand_resume,
-};
-
-static struct platform_driver pxa3xx_nand_driver = {
- .driver = {
- .name = "pxa3xx-nand",
- .of_match_table = pxa3xx_nand_dt_ids,
- .pm = &pxa3xx_nand_pm_ops,
- },
- .probe = pxa3xx_nand_probe,
- .remove = pxa3xx_nand_remove,
-};
-
-module_platform_driver(pxa3xx_nand_driver);
-
-MODULE_LICENSE("GPL");
-MODULE_DESCRIPTION("PXA3xx NAND controller driver");
--
2.11.0
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
^ permalink raw reply related [flat|nested] 19+ messages in thread