From: Bjorn Andersson <bjorn.andersson@linaro.org>
To: Karthikeyan Ramasubramanian <kramasub@codeaurora.org>
Cc: corbet@lwn.net, andy.gross@linaro.org, david.brown@linaro.org,
robh+dt@kernel.org, mark.rutland@arm.com, wsa@the-dreams.de,
gregkh@linuxfoundation.org, linux-doc@vger.kernel.org,
linux-arm-msm@vger.kernel.org, devicetree@vger.kernel.org,
linux-i2c@vger.kernel.org, linux-serial@vger.kernel.org,
jslaby@suse.com
Subject: Re: [PATCH v2 2/7] dt-bindings: soc: qcom: Add device tree binding for GENI SE
Date: Tue, 16 Jan 2018 22:25:58 -0800 [thread overview]
Message-ID: <20180117062558.GB6620@minitux> (raw)
In-Reply-To: <1515805547-22816-3-git-send-email-kramasub@codeaurora.org>
On Fri 12 Jan 17:05 PST 2018, Karthikeyan Ramasubramanian wrote:
> Add device tree binding support for the QCOM GENI SE driver.
>
> Signed-off-by: Karthikeyan Ramasubramanian <kramasub@codeaurora.org>
Better describe the entire GENI, with it's functions in the same
binding.
> ---
> .../devicetree/bindings/soc/qcom/qcom,geni-se.txt | 34 ++++++++++++++++++++++
> 1 file changed, 34 insertions(+)
> create mode 100644 Documentation/devicetree/bindings/soc/qcom/qcom,geni-se.txt
>
> diff --git a/Documentation/devicetree/bindings/soc/qcom/qcom,geni-se.txt b/Documentation/devicetree/bindings/soc/qcom/qcom,geni-se.txt
> new file mode 100644
> index 0000000..66f8a16
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/soc/qcom/qcom,geni-se.txt
> @@ -0,0 +1,34 @@
> +Qualcomm Technologies, Inc. GENI Serial Engine QUP Wrapper Controller
> +
> +Generic Interface (GENI) based Qualcomm Universal Peripheral (QUP) wrapper
> +is a programmable module for supporting a wide range of serial interfaces
> +like UART, SPI, I2C, I3C, etc. A single QUP module can provide upto 8 Serial
> +Interfaces, using its internal Serial Engines. The GENI Serial Engine QUP
> +Wrapper controller is modeled as a node with zero or more child nodes each
> +representing a serial engine.
> +
> +Required properties:
> +- compatible: Must be "qcom,geni-se-qup".
> +- reg: Must contain QUP register address and length.
> +- clock-names: Must contain "m-ahb" and "s-ahb".
> +- clocks: AHB clocks needed by the device.
> +
> +Required properties if child node exists:
> +- #address-cells: Must be 1
> +- #size-cells: Must be 1
But on a 64-bit system, shouldn't these be 2?
> +- ranges: Must be present
> +
> +Properties for children:
> +
> +A GENI based QUP wrapper controller node can contain 0 or more child nodes
> +representing serial devices. These serial devices can be a QCOM UART, I2C
> +controller, spi controller, or some combination of aforementioned devices.
> +
> +Example:
> + qup0: qcom,geniqup0@8c0000 {
I don't see a reason for this to be referenced, so skip the label. And
don't use qcom, in the node name; "geni" would be perfectly fine?
> + compatible = "qcom,geni-se-qup";
> + reg = <0x8c0000 0x6000>;
> + clock-names = "m-ahb", "s-ahb";
> + clocks = <&clock_gcc GCC_QUPV3_WRAP_0_M_AHB_CLK>,
> + <&clock_gcc GCC_QUPV3_WRAP_0_S_AHB_CLK>;
> + }
Regards,
Bjorn
next prev parent reply other threads:[~2018-01-17 6:25 UTC|newest]
Thread overview: 42+ messages / expand[flat|nested] mbox.gz Atom feed top
2018-01-13 1:05 [PATCH v2 0/7] Introduce GENI SE Controller Driver Karthikeyan Ramasubramanian
2018-01-13 1:05 ` [PATCH v2 1/7] qcom-geni-se: Add QCOM GENI SE Driver summary Karthikeyan Ramasubramanian
2018-01-16 16:55 ` Bjorn Andersson
2018-01-29 21:52 ` Karthik Ramasubramanian
2018-01-13 1:05 ` [PATCH v2 2/7] dt-bindings: soc: qcom: Add device tree binding for GENI SE Karthikeyan Ramasubramanian
2018-01-17 6:25 ` Bjorn Andersson [this message]
2018-01-19 22:53 ` Rob Herring
2018-02-26 21:24 ` Karthik Ramasubramanian
2018-01-13 1:05 ` [PATCH v2 4/7] dt-bindings: i2c: Add device tree bindings for GENI I2C Controller Karthikeyan Ramasubramanian
[not found] ` <1515805547-22816-5-git-send-email-kramasub-sgV2jX0FEOL9JmXXK+q4OQ@public.gmane.org>
2018-01-17 6:31 ` Bjorn Andersson
2018-02-26 21:28 ` Karthik Ramasubramanian
2018-01-13 1:05 ` [PATCH v2 6/7] dt-bindings: serial: Add bindings for GENI based UART Controller Karthikeyan Ramasubramanian
2018-01-17 6:35 ` Bjorn Andersson
2018-02-27 13:25 ` Karthik Ramasubramanian
2018-01-13 1:05 ` [PATCH v2 7/7] tty: serial: msm_geni_serial: Add serial driver support for GENI based QUP Karthikeyan Ramasubramanian
2018-01-18 19:43 ` Bjorn Andersson
2018-01-19 7:12 ` Bjorn Andersson
2018-02-27 15:07 ` Karthik Ramasubramanian
2018-01-24 23:07 ` [v2, " Evan Green
2018-02-14 11:04 ` [PATCH v2 " Amit Kucheria
2018-02-23 18:06 ` [v2, " Guenter Roeck
2018-02-27 13:23 ` Karthik Ramasubramanian
2018-02-23 19:05 ` Doug Anderson
[not found] ` <1515805547-22816-1-git-send-email-kramasub-sgV2jX0FEOL9JmXXK+q4OQ@public.gmane.org>
2018-01-13 1:05 ` [PATCH v2 3/7] soc: qcom: Add GENI based QUP Wrapper driver Karthikeyan Ramasubramanian
2018-01-17 6:20 ` Bjorn Andersson
2018-01-18 9:13 ` Rajendra Nayak
2018-01-18 16:57 ` Bjorn Andersson
2018-01-19 22:57 ` Rob Herring
2018-01-31 19:02 ` Karthik Ramasubramanian
[not found] ` <1abb0679-1997-9b70-30bd-d3472cea7053-sgV2jX0FEOL9JmXXK+q4OQ@public.gmane.org>
2018-02-05 23:53 ` Bjorn Andersson
2018-01-31 18:58 ` Karthik Ramasubramanian
2018-02-05 23:50 ` Bjorn Andersson
[not found] ` <1515805547-22816-4-git-send-email-kramasub-sgV2jX0FEOL9JmXXK+q4OQ@public.gmane.org>
2018-01-24 23:06 ` [v2,3/7] " Evan Green
2018-01-26 19:38 ` Doug Anderson
2018-02-14 11:07 ` [PATCH v2 3/7] " Amit Kucheria
2018-02-16 20:44 ` Karthik Ramasubramanian
2018-01-13 1:05 ` [PATCH v2 5/7] i2c: i2c-qcom-geni: Add bus driver for the Qualcomm GENI I2C controller Karthikeyan Ramasubramanian
[not found] ` <1515805547-22816-6-git-send-email-kramasub-sgV2jX0FEOL9JmXXK+q4OQ@public.gmane.org>
2018-01-18 5:23 ` Bjorn Andersson
2018-02-27 13:16 ` Karthik Ramasubramanian
2018-01-24 23:07 ` [v2, " Evan Green
2018-01-19 18:32 ` [PATCH v2 0/7] Introduce GENI SE Controller Driver Randy Dunlap
2018-01-31 18:59 ` Karthik Ramasubramanian
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20180117062558.GB6620@minitux \
--to=bjorn.andersson@linaro.org \
--cc=andy.gross@linaro.org \
--cc=corbet@lwn.net \
--cc=david.brown@linaro.org \
--cc=devicetree@vger.kernel.org \
--cc=gregkh@linuxfoundation.org \
--cc=jslaby@suse.com \
--cc=kramasub@codeaurora.org \
--cc=linux-arm-msm@vger.kernel.org \
--cc=linux-doc@vger.kernel.org \
--cc=linux-i2c@vger.kernel.org \
--cc=linux-serial@vger.kernel.org \
--cc=mark.rutland@arm.com \
--cc=robh+dt@kernel.org \
--cc=wsa@the-dreams.de \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).