* [v3] ARM: dts: imx: Add support for Advantech DMS-BA16
@ 2018-02-06 19:17 Ken Lin
[not found] ` <20180206191704.7933-1-yungching0725-Re5JQEeQqe8AvxtiuMwx3w@public.gmane.org>
0 siblings, 1 reply; 4+ messages in thread
From: Ken Lin @ 2018-02-06 19:17 UTC (permalink / raw)
To: shawnguo
Cc: mark.rutland, devicetree, linux, linux-kernel, robh+dt, kernel,
fabio.estevam, linux-arm-kernel
Add support for Advantech DMS-BA16 board, which uses
the Advantech BA-16 module.
Signed-off-by: Ken Lin <yungching0725@gmail.com>
---
Changes in v3:
- Fix the SPDX lines issue
- Fix the eeprom setting issue
arch/arm/boot/dts/Makefile | 1 +
arch/arm/boot/dts/imx6q-dms-ba16.dts | 140 +++++++++++++++++++++++++++++++++++
2 files changed, 141 insertions(+)
create mode 100644 arch/arm/boot/dts/imx6q-dms-ba16.dts
diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
index ade7a38543dc..585c3da4a47a 100644
--- a/arch/arm/boot/dts/Makefile
+++ b/arch/arm/boot/dts/Makefile
@@ -435,6 +435,7 @@ dtb-$(CONFIG_SOC_IMX6Q) += \
imx6q-dfi-fs700-m60.dtb \
imx6q-display5-tianma-tm070-1280x768.dtb \
imx6q-dmo-edmqmx6.dtb \
+ imx6q-dms-ba16.dtb \
imx6q-evi.dtb \
imx6q-gk802.dtb \
imx6q-gw51xx.dtb \
diff --git a/arch/arm/boot/dts/imx6q-dms-ba16.dts b/arch/arm/boot/dts/imx6q-dms-ba16.dts
new file mode 100644
index 000000000000..b5047fd88290
--- /dev/null
+++ b/arch/arm/boot/dts/imx6q-dms-ba16.dts
@@ -0,0 +1,140 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+
+/dts-v1/;
+
+#include <dt-bindings/gpio/gpio.h>
+#include "imx6q-ba16.dtsi"
+
+/ {
+ model = "Advantech DMS-BA16";
+ compatible = "advantech,imx6q-dms-ba16", "advantech,imx6q-ba16", "fsl,imx6q";
+
+ reg_usb_otg_vbus: regulator-usbotgvbus {
+ compatible = "regulator-fixed";
+ regulator-name = "usb_otg_vbus";
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_usbotgvbus>;
+ gpio = <&gpio4 15 GPIO_ACTIVE_HIGH>;
+ enable-active-high;
+ };
+
+ sys_mclk: clock-sys-mclk {
+ compatible = "fixed-clock";
+ #clock-cells = <0>;
+ clock-frequency = <22000000>;
+ };
+
+ sound {
+ compatible = "fsl,imx6q-ba16-sgtl5000",
+ "fsl,imx-audio-sgtl5000";
+ model = "imx6q-ba16-sgtl5000";
+ ssi-controller = <&ssi1>;
+ audio-codec = <&sgtl5000>;
+ audio-routing =
+ "MIC_IN", "Mic Jack",
+ "Mic Jack", "Mic Bias",
+ "Headphone Jack", "HP_OUT";
+ mux-int-port = <1>;
+ mux-ext-port = <4>;
+ };
+};
+
+&ecspi5 {
+ cs-gpios = <&gpio1 17 GPIO_ACTIVE_HIGH>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_ecspi5>;
+ status = "okay";
+
+ m25_eeprom: m25p80@0 {
+ compatible = "atmel,at25256B", "atmel,at25";
+ spi-max-frequency = <20000000>;
+ size = <0x8000>;
+ pagesize = <64>;
+ reg = <0>;
+ address-width = <16>;
+ };
+};
+
+&iomuxc {
+
+ pinctrl_usbotgvbus: usbotgvbusgrp {
+ fsl,pins = <
+ MX6QDL_PAD_KEY_ROW4__GPIO4_IO15 0x000b0
+ MX6QDL_PAD_GPIO_1__USB_OTG_ID 0x17059
+ >;
+ };
+
+ pinctrl_i2c1_gpio: i2c1gpiogrp {
+ fsl,pins = <
+ MX6QDL_PAD_CSI0_DAT8__GPIO5_IO26 0x1b0b0
+ MX6QDL_PAD_CSI0_DAT9__GPIO5_IO27 0x1b0b0
+ >;
+ };
+
+ pinctrl_i2c2_gpio: i2c2gpiogrp {
+ fsl,pins = <
+ MX6QDL_PAD_KEY_COL3__GPIO4_IO12 0x1b0b0
+ MX6QDL_PAD_KEY_ROW3__GPIO4_IO13 0x1b0b0
+ >;
+ };
+
+ pinctrl_i2c3_gpio: i2c3gpiogrp {
+ fsl,pins = <
+ MX6QDL_PAD_GPIO_3__GPIO1_IO03 0x1b0b0
+ MX6QDL_PAD_GPIO_6__GPIO1_IO06 0x1b0b0
+ >;
+ };
+};
+
+&i2c1 {
+ clock-frequency = <100000>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_i2c1>;
+ status = "okay";
+
+ sgtl5000: codec@a {
+ compatible = "fsl,sgtl5000";
+ reg = <0x0a>;
+ clocks = <&sys_mclk>;
+ lrclk-strength = <0x3>;
+ VDDA-supply = <®_1p8v>;
+ VDDIO-supply = <®_3p3v>;
+ };
+};
+
+&pwm2 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_pwm2>;
+ status = "okay";
+};
+
+&sata {
+ fsl,no-spread-spectrum;
+ fsl,transmit-atten-16ths = <12>;
+ fsl,transmit-boost-mdB = <3330>;
+ fsl,transmit-level-mV = <1133>;
+ fsl,receive-dpll-mode = <1>;
+ status = "okay";
+};
+
+&usbotg {
+ vbus-supply = <®_usb_otg_vbus>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_usbotg>;
+ dr_mode = "otg";
+ disable-over-current;
+ status = "okay";
+};
+
+&usdhc4 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_usdhc4>;
+ bus-width = <8>;
+ cd-gpios = <&gpio6 11 GPIO_ACTIVE_LOW>;
+ no-1-8-v;
+ keep-power-in-suspend;
+ wakeup-source;
+ status = "okay";
+};
--
2.11.0
^ permalink raw reply related [flat|nested] 4+ messages in thread
* Re: [v3] ARM: dts: imx: Add support for Advantech DMS-BA16
[not found] ` <20180206191704.7933-1-yungching0725-Re5JQEeQqe8AvxtiuMwx3w@public.gmane.org>
@ 2018-02-08 9:03 ` Shawn Guo
2018-02-08 19:24 ` Yung-Ching LIN
0 siblings, 1 reply; 4+ messages in thread
From: Shawn Guo @ 2018-02-08 9:03 UTC (permalink / raw)
To: Ken Lin
Cc: kernel-bIcnvbaLZ9MEGnE8C9+IrQ, fabio.estevam-3arQi8VN3Tc,
robh+dt-DgEjT+Ai2ygdnm+yROfE0A, mark.rutland-5wv7dgnIgG8,
linux-I+IVW8TIWO2tmTQ+vhA3Yw,
linux-arm-kernel-IAPFreCvJWM7uuMidbF8XUB+6BGkLq7r,
devicetree-u79uwXL29TY76Z2rM5mHXA,
linux-kernel-u79uwXL29TY76Z2rM5mHXA
On Wed, Feb 07, 2018 at 03:17:04AM +0800, Ken Lin wrote:
> Add support for Advantech DMS-BA16 board, which uses
> the Advantech BA-16 module.
>
> Signed-off-by: Ken Lin <yungching0725-Re5JQEeQqe8AvxtiuMwx3w@public.gmane.org>
> ---
> Changes in v3:
> - Fix the SPDX lines issue
> - Fix the eeprom setting issue
>
> arch/arm/boot/dts/Makefile | 1 +
> arch/arm/boot/dts/imx6q-dms-ba16.dts | 140 +++++++++++++++++++++++++++++++++++
> 2 files changed, 141 insertions(+)
> create mode 100644 arch/arm/boot/dts/imx6q-dms-ba16.dts
>
> diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
> index ade7a38543dc..585c3da4a47a 100644
> --- a/arch/arm/boot/dts/Makefile
> +++ b/arch/arm/boot/dts/Makefile
> @@ -435,6 +435,7 @@ dtb-$(CONFIG_SOC_IMX6Q) += \
> imx6q-dfi-fs700-m60.dtb \
> imx6q-display5-tianma-tm070-1280x768.dtb \
> imx6q-dmo-edmqmx6.dtb \
> + imx6q-dms-ba16.dtb \
> imx6q-evi.dtb \
> imx6q-gk802.dtb \
> imx6q-gw51xx.dtb \
> diff --git a/arch/arm/boot/dts/imx6q-dms-ba16.dts b/arch/arm/boot/dts/imx6q-dms-ba16.dts
> new file mode 100644
> index 000000000000..b5047fd88290
> --- /dev/null
> +++ b/arch/arm/boot/dts/imx6q-dms-ba16.dts
> @@ -0,0 +1,140 @@
> +// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
> +
> +/dts-v1/;
> +
> +#include <dt-bindings/gpio/gpio.h>
> +#include "imx6q-ba16.dtsi"
> +
> +/ {
> + model = "Advantech DMS-BA16";
> + compatible = "advantech,imx6q-dms-ba16", "advantech,imx6q-ba16", "fsl,imx6q";
> +
> + reg_usb_otg_vbus: regulator-usbotgvbus {
> + compatible = "regulator-fixed";
> + regulator-name = "usb_otg_vbus";
> + regulator-min-microvolt = <5000000>;
> + regulator-max-microvolt = <5000000>;
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_usbotgvbus>;
> + gpio = <&gpio4 15 GPIO_ACTIVE_HIGH>;
> + enable-active-high;
> + };
> +
> + sys_mclk: clock-sys-mclk {
> + compatible = "fixed-clock";
> + #clock-cells = <0>;
> + clock-frequency = <22000000>;
> + };
> +
> + sound {
> + compatible = "fsl,imx6q-ba16-sgtl5000",
> + "fsl,imx-audio-sgtl5000";
> + model = "imx6q-ba16-sgtl5000";
> + ssi-controller = <&ssi1>;
> + audio-codec = <&sgtl5000>;
> + audio-routing =
> + "MIC_IN", "Mic Jack",
> + "Mic Jack", "Mic Bias",
> + "Headphone Jack", "HP_OUT";
> + mux-int-port = <1>;
> + mux-ext-port = <4>;
> + };
> +};
> +
> +&ecspi5 {
> + cs-gpios = <&gpio1 17 GPIO_ACTIVE_HIGH>;
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_ecspi5>;
> + status = "okay";
> +
> + m25_eeprom: m25p80@0 {
> + compatible = "atmel,at25256B", "atmel,at25";
> + spi-max-frequency = <20000000>;
> + size = <0x8000>;
> + pagesize = <64>;
> + reg = <0>;
> + address-width = <16>;
> + };
> +};
> +
> +&iomuxc {
> +
Unnecessary newline.
> + pinctrl_usbotgvbus: usbotgvbusgrp {
Please keep the pinctrl entries under iomuxc node alphabetically sorted.
> + fsl,pins = <
> + MX6QDL_PAD_KEY_ROW4__GPIO4_IO15 0x000b0
> + MX6QDL_PAD_GPIO_1__USB_OTG_ID 0x17059
MX6QDL_PAD_GPIO_1__USB_OTG_ID shouldn't belong to this group but
pinctrl_usbotg. However that has been defined in imx6q-ba16.dtsi using
another USB_OTG_ID pinmux. Confusing.
Shawn
> + >;
> + };
> +
> + pinctrl_i2c1_gpio: i2c1gpiogrp {
> + fsl,pins = <
> + MX6QDL_PAD_CSI0_DAT8__GPIO5_IO26 0x1b0b0
> + MX6QDL_PAD_CSI0_DAT9__GPIO5_IO27 0x1b0b0
> + >;
> + };
> +
> + pinctrl_i2c2_gpio: i2c2gpiogrp {
> + fsl,pins = <
> + MX6QDL_PAD_KEY_COL3__GPIO4_IO12 0x1b0b0
> + MX6QDL_PAD_KEY_ROW3__GPIO4_IO13 0x1b0b0
> + >;
> + };
> +
> + pinctrl_i2c3_gpio: i2c3gpiogrp {
> + fsl,pins = <
> + MX6QDL_PAD_GPIO_3__GPIO1_IO03 0x1b0b0
> + MX6QDL_PAD_GPIO_6__GPIO1_IO06 0x1b0b0
> + >;
> + };
> +};
> +
> +&i2c1 {
> + clock-frequency = <100000>;
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_i2c1>;
> + status = "okay";
> +
> + sgtl5000: codec@a {
> + compatible = "fsl,sgtl5000";
> + reg = <0x0a>;
> + clocks = <&sys_mclk>;
> + lrclk-strength = <0x3>;
> + VDDA-supply = <®_1p8v>;
> + VDDIO-supply = <®_3p3v>;
> + };
> +};
> +
> +&pwm2 {
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_pwm2>;
> + status = "okay";
> +};
> +
> +&sata {
> + fsl,no-spread-spectrum;
> + fsl,transmit-atten-16ths = <12>;
> + fsl,transmit-boost-mdB = <3330>;
> + fsl,transmit-level-mV = <1133>;
> + fsl,receive-dpll-mode = <1>;
> + status = "okay";
> +};
> +
> +&usbotg {
> + vbus-supply = <®_usb_otg_vbus>;
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_usbotg>;
> + dr_mode = "otg";
> + disable-over-current;
> + status = "okay";
> +};
> +
> +&usdhc4 {
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_usdhc4>;
> + bus-width = <8>;
> + cd-gpios = <&gpio6 11 GPIO_ACTIVE_LOW>;
> + no-1-8-v;
> + keep-power-in-suspend;
> + wakeup-source;
> + status = "okay";
> +};
> --
> 2.11.0
>
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
^ permalink raw reply [flat|nested] 4+ messages in thread
* Re: [v3] ARM: dts: imx: Add support for Advantech DMS-BA16
2018-02-08 9:03 ` Shawn Guo
@ 2018-02-08 19:24 ` Yung-Ching LIN
2018-02-09 3:00 ` Shawn Guo
0 siblings, 1 reply; 4+ messages in thread
From: Yung-Ching LIN @ 2018-02-08 19:24 UTC (permalink / raw)
To: Shawn Guo
Cc: Sascha Hauer, Fabio Estevam, Rob Herring, Mark Rutland,
Russell King - ARM Linux,
moderated list:ARM/FREESCALE IMX / MXC ARM ARCHITECTURE,
open list:OPEN FIRMWARE AND FLATTENED DEVICE TREE BINDINGS,
linux-kernel
Hi Shawn,
Thanks for pointing out the issues.
Please see my inline comments below.
On Thu, Feb 8, 2018 at 1:03 AM, Shawn Guo <shawnguo@kernel.org> wrote:
> On Wed, Feb 07, 2018 at 03:17:04AM +0800, Ken Lin wrote:
>> Add support for Advantech DMS-BA16 board, which uses
>> the Advantech BA-16 module.
>>
>> Signed-off-by: Ken Lin <yungching0725@gmail.com>
>> ---
>> Changes in v3:
>> - Fix the SPDX lines issue
>> - Fix the eeprom setting issue
>>
>> arch/arm/boot/dts/Makefile | 1 +
>> arch/arm/boot/dts/imx6q-dms-ba16.dts | 140 +++++++++++++++++++++++++++++++++++
>> 2 files changed, 141 insertions(+)
>> create mode 100644 arch/arm/boot/dts/imx6q-dms-ba16.dts
>>
>> diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
>> index ade7a38543dc..585c3da4a47a 100644
>> --- a/arch/arm/boot/dts/Makefile
>> +++ b/arch/arm/boot/dts/Makefile
>> @@ -435,6 +435,7 @@ dtb-$(CONFIG_SOC_IMX6Q) += \
>> imx6q-dfi-fs700-m60.dtb \
>> imx6q-display5-tianma-tm070-1280x768.dtb \
>> imx6q-dmo-edmqmx6.dtb \
>> + imx6q-dms-ba16.dtb \
>> imx6q-evi.dtb \
>> imx6q-gk802.dtb \
>> imx6q-gw51xx.dtb \
>> diff --git a/arch/arm/boot/dts/imx6q-dms-ba16.dts b/arch/arm/boot/dts/imx6q-dms-ba16.dts
>> new file mode 100644
>> index 000000000000..b5047fd88290
>> --- /dev/null
>> +++ b/arch/arm/boot/dts/imx6q-dms-ba16.dts
>> @@ -0,0 +1,140 @@
>> +// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
>> +
>> +/dts-v1/;
>> +
>> +#include <dt-bindings/gpio/gpio.h>
>> +#include "imx6q-ba16.dtsi"
>> +
>> +/ {
>> + model = "Advantech DMS-BA16";
>> + compatible = "advantech,imx6q-dms-ba16", "advantech,imx6q-ba16", "fsl,imx6q";
>> +
>> + reg_usb_otg_vbus: regulator-usbotgvbus {
>> + compatible = "regulator-fixed";
>> + regulator-name = "usb_otg_vbus";
>> + regulator-min-microvolt = <5000000>;
>> + regulator-max-microvolt = <5000000>;
>> + pinctrl-names = "default";
>> + pinctrl-0 = <&pinctrl_usbotgvbus>;
>> + gpio = <&gpio4 15 GPIO_ACTIVE_HIGH>;
>> + enable-active-high;
>> + };
>> +
>> + sys_mclk: clock-sys-mclk {
>> + compatible = "fixed-clock";
>> + #clock-cells = <0>;
>> + clock-frequency = <22000000>;
>> + };
>> +
>> + sound {
>> + compatible = "fsl,imx6q-ba16-sgtl5000",
>> + "fsl,imx-audio-sgtl5000";
>> + model = "imx6q-ba16-sgtl5000";
>> + ssi-controller = <&ssi1>;
>> + audio-codec = <&sgtl5000>;
>> + audio-routing =
>> + "MIC_IN", "Mic Jack",
>> + "Mic Jack", "Mic Bias",
>> + "Headphone Jack", "HP_OUT";
>> + mux-int-port = <1>;
>> + mux-ext-port = <4>;
>> + };
>> +};
>> +
>> +&ecspi5 {
>> + cs-gpios = <&gpio1 17 GPIO_ACTIVE_HIGH>;
>> + pinctrl-names = "default";
>> + pinctrl-0 = <&pinctrl_ecspi5>;
>> + status = "okay";
>> +
>> + m25_eeprom: m25p80@0 {
>> + compatible = "atmel,at25256B", "atmel,at25";
>> + spi-max-frequency = <20000000>;
>> + size = <0x8000>;
>> + pagesize = <64>;
>> + reg = <0>;
>> + address-width = <16>;
>> + };
>> +};
>> +
>> +&iomuxc {
>> +
>
> Unnecessary newline.
>
Thanks. Will fix this in the v4.
>> + pinctrl_usbotgvbus: usbotgvbusgrp {
>
> Please keep the pinctrl entries under iomuxc node alphabetically sorted.
>
Thanks. Will fix this in the v4.
>> + fsl,pins = <
>> + MX6QDL_PAD_KEY_ROW4__GPIO4_IO15 0x000b0
>> + MX6QDL_PAD_GPIO_1__USB_OTG_ID 0x17059
>
> MX6QDL_PAD_GPIO_1__USB_OTG_ID shouldn't belong to this group but
> pinctrl_usbotg. However that has been defined in imx6q-ba16.dtsi using
> another USB_OTG_ID pinmux. Confusing.
>
> Shawn
Will correct the USB_OTG_ID pinmux setting in the v4.
Do you mind if I redefine reg_usb_otg_vbus node since we just started
using OTG host/device mode on this board ?
>
>> + >;
>> + };
>> +
>> + pinctrl_i2c1_gpio: i2c1gpiogrp {
>> + fsl,pins = <
>> + MX6QDL_PAD_CSI0_DAT8__GPIO5_IO26 0x1b0b0
>> + MX6QDL_PAD_CSI0_DAT9__GPIO5_IO27 0x1b0b0
>> + >;
>> + };
>> +
>> + pinctrl_i2c2_gpio: i2c2gpiogrp {
>> + fsl,pins = <
>> + MX6QDL_PAD_KEY_COL3__GPIO4_IO12 0x1b0b0
>> + MX6QDL_PAD_KEY_ROW3__GPIO4_IO13 0x1b0b0
>> + >;
>> + };
>> +
>> + pinctrl_i2c3_gpio: i2c3gpiogrp {
>> + fsl,pins = <
>> + MX6QDL_PAD_GPIO_3__GPIO1_IO03 0x1b0b0
>> + MX6QDL_PAD_GPIO_6__GPIO1_IO06 0x1b0b0
>> + >;
>> + };
>> +};
>> +
>> +&i2c1 {
>> + clock-frequency = <100000>;
>> + pinctrl-names = "default";
>> + pinctrl-0 = <&pinctrl_i2c1>;
>> + status = "okay";
>> +
>> + sgtl5000: codec@a {
>> + compatible = "fsl,sgtl5000";
>> + reg = <0x0a>;
>> + clocks = <&sys_mclk>;
>> + lrclk-strength = <0x3>;
>> + VDDA-supply = <®_1p8v>;
>> + VDDIO-supply = <®_3p3v>;
>> + };
>> +};
>> +
>> +&pwm2 {
>> + pinctrl-names = "default";
>> + pinctrl-0 = <&pinctrl_pwm2>;
>> + status = "okay";
>> +};
>> +
>> +&sata {
>> + fsl,no-spread-spectrum;
>> + fsl,transmit-atten-16ths = <12>;
>> + fsl,transmit-boost-mdB = <3330>;
>> + fsl,transmit-level-mV = <1133>;
>> + fsl,receive-dpll-mode = <1>;
>> + status = "okay";
>> +};
>> +
>> +&usbotg {
>> + vbus-supply = <®_usb_otg_vbus>;
>> + pinctrl-names = "default";
>> + pinctrl-0 = <&pinctrl_usbotg>;
>> + dr_mode = "otg";
>> + disable-over-current;
>> + status = "okay";
>> +};
>> +
>> +&usdhc4 {
>> + pinctrl-names = "default";
>> + pinctrl-0 = <&pinctrl_usdhc4>;
>> + bus-width = <8>;
>> + cd-gpios = <&gpio6 11 GPIO_ACTIVE_LOW>;
>> + no-1-8-v;
>> + keep-power-in-suspend;
>> + wakeup-source;
>> + status = "okay";
>> +};
>> --
>> 2.11.0
>>
^ permalink raw reply [flat|nested] 4+ messages in thread
* Re: [v3] ARM: dts: imx: Add support for Advantech DMS-BA16
2018-02-08 19:24 ` Yung-Ching LIN
@ 2018-02-09 3:00 ` Shawn Guo
0 siblings, 0 replies; 4+ messages in thread
From: Shawn Guo @ 2018-02-09 3:00 UTC (permalink / raw)
To: Yung-Ching LIN
Cc: Sascha Hauer, Fabio Estevam, Rob Herring, Mark Rutland,
Russell King - ARM Linux,
moderated list:ARM/FREESCALE IMX / MXC ARM ARCHITECTURE,
open list:OPEN FIRMWARE AND FLATTENED DEVICE TREE BINDINGS,
linux-kernel
On Thu, Feb 08, 2018 at 11:24:53AM -0800, Yung-Ching LIN wrote:
> Will correct the USB_OTG_ID pinmux setting in the v4.
> Do you mind if I redefine reg_usb_otg_vbus node since we just started
> using OTG host/device mode on this board ?
Not at all. Feel free to change it.
Shawn
^ permalink raw reply [flat|nested] 4+ messages in thread
end of thread, other threads:[~2018-02-09 3:00 UTC | newest]
Thread overview: 4+ messages (download: mbox.gz / follow: Atom feed)
-- links below jump to the message on this page --
2018-02-06 19:17 [v3] ARM: dts: imx: Add support for Advantech DMS-BA16 Ken Lin
[not found] ` <20180206191704.7933-1-yungching0725-Re5JQEeQqe8AvxtiuMwx3w@public.gmane.org>
2018-02-08 9:03 ` Shawn Guo
2018-02-08 19:24 ` Yung-Ching LIN
2018-02-09 3:00 ` Shawn Guo
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).