[PATCH v2 1/2] media: ov2680: dt: Add bindings for OV2680

[PATCH v2 1/2] media: ov2680: dt: Add bindings for OV2680

[Rui Miguel Silva]

Add device tree binding documentation for the OV2680 camera sensor.

CC: devicetree@vger.kernel.org
Signed-off-by: Rui Miguel Silva <rui.silva@linaro.org>
---
 .../devicetree/bindings/media/i2c/ov2680.txt       | 40 ++++++++++++++++++++++
 1 file changed, 40 insertions(+)
 create mode 100644 Documentation/devicetree/bindings/media/i2c/ov2680.txt

diff --git a/Documentation/devicetree/bindings/media/i2c/ov2680.txt b/Documentation/devicetree/bindings/media/i2c/ov2680.txt
new file mode 100644
index 000000000000..0e29f1a113c0
--- /dev/null
+++ b/Documentation/devicetree/bindings/media/i2c/ov2680.txt
@@ -0,0 +1,40 @@
+* Omnivision OV2680 MIPI CSI-2 sensor
+
+Required Properties:
+- compatible: should be "ovti,ov2680".
+- clocks: reference to the xvclk input clock.
+- clock-names: should be "xvclk".
+
+Optional Properties:
+- powerdown-gpios: reference to the GPIO connected to the powerdown pin,
+		     if any. This is an active high signal to the OV2680.
+
+The device node must contain one 'port' child node for its digital output
+video port, and this port must have a single endpoint in accordance with
+ the video interface bindings defined in
+Documentation/devicetree/bindings/media/video-interfaces.txt.
+
+Endpoint node required properties for CSI-2 connection are:
+- remote-endpoint: a phandle to the bus receiver's endpoint node.
+- clock-lanes: should be set to <0> (clock lane on hardware lane 0).
+- data-lanes: should be set to <1> (one CSI-2 lane supported).
+ 
+Example:
+
+&i2c2 {
+	ov2680: camera-sensor@36 {
+		compatible = "ovti,ov2680";
+		reg = <0x36>;
+		clocks = <&osc>;
+		clock-names = "xvclk";
+		powerdown-gpios = <&gpio1 3 GPIO_ACTIVE_HIGH>;
+
+		port {
+			ov2680_mipi_ep: endpoint {
+				remote-endpoint = <&mipi_sensor_ep>;
+				clock-lanes = <0>;
+				data-lanes = <1>;
+			};
+		};
+	};
+};
-- 
2.16.2

Re: [PATCH v2 1/2] media: ov2680: dt: Add bindings for OV2680

[Rob Herring]

On Wed, Feb 28, 2018 at 03:27:22PM +0000, Rui Miguel Silva wrote:
> Add device tree binding documentation for the OV2680 camera sensor.
> 
> CC: devicetree@vger.kernel.org
> Signed-off-by: Rui Miguel Silva <rui.silva@linaro.org>
> ---
>  .../devicetree/bindings/media/i2c/ov2680.txt       | 40 ++++++++++++++++++++++
>  1 file changed, 40 insertions(+)
>  create mode 100644 Documentation/devicetree/bindings/media/i2c/ov2680.txt

Reviewed-by: Rob Herring <robh@kernel.org>