* [PATCH v3 0/2] Add basic support for pico-pi-imx8m
@ 2019-07-18 12:16 Andra Danciu
2019-07-18 12:16 ` [PATCH v3 1/2] arm64: dts: fsl: pico-pi: Add a device tree for the PICO-PI-IMX8M Andra Danciu
2019-07-18 12:16 ` [PATCH v3 2/2] dt-bindings: arm: fsl: Add the pico-pi-imx8m board Andra Danciu
0 siblings, 2 replies; 5+ messages in thread
From: Andra Danciu @ 2019-07-18 12:16 UTC (permalink / raw)
To: shawnguo
Cc: robh+dt, mark.rutland, manivannan.sadhasivam, andrew.smirnov,
u.kleine-koenig, aisheng.dong, andradanciu1997, leoyang.li,
festevam, sriram.dash, l.stach, pankaj.bansal, ping.bai,
pramod.kumar_1, bhaskar.upadhaya, richard.hu, devicetree,
linux-kernel
Add support for TechNexion PICO-PI-IMX8M based on patches from Richard Hu
Datasheet is at: https://s3.us-east-2.amazonaws.com/technexion/datasheets/picopiimx8m.pdf
Changes since v2:
- changed PICO-PI-8M bord compatible from wand,imx8mq-pico-pi to
technexion,pico-pi-imx8m
- removed bootargs property
- removed regulators node and put fixed regulator directly under root node
- changed node name from usb_otg_vbus to regulator-usb-otg-vbus
- removed pinctrl-names property from iomuxc node
- removed wand-pi-8m container node
- sorted pinctrl nodes alphabetically
- removed tusb320_irqgrp, tusb320_irqgrp nodes because there is no upstream
driver
- changed properties' order in usb_dwc3_1 node
Changes since v1:
- renamed wandboard-pi-8m.dts to pico-pi-8m.dts
- removed pinctrl_csi1, pinctrl_wifi_ctrl
- used generic name for pmic
- removed gpo node
- delete regulator-virtuals node
- remove always-on property from buck1-8 and ldo3-7
- remove pmic-buck-uses-i2c-dvs property for buck1-4
Andra Danciu (1):
dt-bindings: arm: fsl: Add the pico-pi-imx8m board
Richard Hu (1):
arm64: dts: fsl: pico-pi: Add a device tree for the PICO-PI-IMX8M
Documentation/devicetree/bindings/arm/fsl.yaml | 1 +
arch/arm64/boot/dts/freescale/Makefile | 1 +
arch/arm64/boot/dts/freescale/pico-pi-8m.dts | 417 +++++++++++++++++++++++++
3 files changed, 419 insertions(+)
create mode 100644 arch/arm64/boot/dts/freescale/pico-pi-8m.dts
--
2.11.0
^ permalink raw reply [flat|nested] 5+ messages in thread
* [PATCH v3 1/2] arm64: dts: fsl: pico-pi: Add a device tree for the PICO-PI-IMX8M
2019-07-18 12:16 [PATCH v3 0/2] Add basic support for pico-pi-imx8m Andra Danciu
@ 2019-07-18 12:16 ` Andra Danciu
2019-07-18 23:05 ` Fabio Estevam
2019-07-18 12:16 ` [PATCH v3 2/2] dt-bindings: arm: fsl: Add the pico-pi-imx8m board Andra Danciu
1 sibling, 1 reply; 5+ messages in thread
From: Andra Danciu @ 2019-07-18 12:16 UTC (permalink / raw)
To: shawnguo
Cc: robh+dt, mark.rutland, manivannan.sadhasivam, andrew.smirnov,
u.kleine-koenig, aisheng.dong, andradanciu1997, leoyang.li,
festevam, sriram.dash, l.stach, pankaj.bansal, ping.bai,
pramod.kumar_1, bhaskar.upadhaya, richard.hu, devicetree,
linux-kernel
From: Richard Hu <richard.hu@technexion.com>
The current level of support yields a working console and is able to boot
userspace from NFS or init ramdisk.
Additional subsystems that are active :
- Ethernet
- USB
Cc: Daniel Baluta <daniel.baluta@nxp.com>
Signed-off-by: Richard Hu <richard.hu@technexion.com>
Signed-off-by: Andra Danciu <andradanciu1997@gmail.com>
---
arch/arm64/boot/dts/freescale/Makefile | 1 +
arch/arm64/boot/dts/freescale/pico-pi-8m.dts | 417 +++++++++++++++++++++++++++
2 files changed, 418 insertions(+)
create mode 100644 arch/arm64/boot/dts/freescale/pico-pi-8m.dts
diff --git a/arch/arm64/boot/dts/freescale/Makefile b/arch/arm64/boot/dts/freescale/Makefile
index c043aca66572..538422903e8a 100644
--- a/arch/arm64/boot/dts/freescale/Makefile
+++ b/arch/arm64/boot/dts/freescale/Makefile
@@ -26,3 +26,4 @@ dtb-$(CONFIG_ARCH_MXC) += imx8mq-librem5-devkit.dtb
dtb-$(CONFIG_ARCH_MXC) += imx8mq-zii-ultra-rmb3.dtb
dtb-$(CONFIG_ARCH_MXC) += imx8mq-zii-ultra-zest.dtb
dtb-$(CONFIG_ARCH_MXC) += imx8qxp-mek.dtb
+dtb-$(CONFIG_ARCH_MXC) += pico-pi-8m.dtb
diff --git a/arch/arm64/boot/dts/freescale/pico-pi-8m.dts b/arch/arm64/boot/dts/freescale/pico-pi-8m.dts
new file mode 100644
index 000000000000..30f1d85119d0
--- /dev/null
+++ b/arch/arm64/boot/dts/freescale/pico-pi-8m.dts
@@ -0,0 +1,417 @@
+// SPDX-License-Identifier: GPL-2.0+
+/*
+ * Copyright 2018 Wandboard, Org.
+ * Copyright 2017 NXP
+ *
+ * Author: Richard Hu <hakahu@gmail.com>
+ */
+
+/dts-v1/;
+
+#include "imx8mq.dtsi"
+
+/ {
+ model = "TechNexion PICO-PI-8M";
+ compatible = "technexion,pico-pi-imx8m", "fsl,imx8mq";
+
+ chosen {
+ stdout-path = &uart1;
+ };
+
+ reg_usb_otg_vbus: regulator-usb-otg-vbus {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_otg_vbus>;
+ compatible = "regulator-fixed";
+ regulator-name = "usb_otg_vbus";
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ gpio = <&gpio3 14 GPIO_ACTIVE_LOW>;
+ };
+};
+
+&iomuxc {
+ pinctrl_enet_3v3: enet3v3grp {
+ fsl,pins = <
+ MX8MQ_IOMUXC_GPIO1_IO00_GPIO1_IO0 0x19
+ >;
+ };
+
+ pinctrl_fec1: fec1grp {
+ fsl,pins = <
+ MX8MQ_IOMUXC_ENET_MDC_ENET1_MDC 0x3
+ MX8MQ_IOMUXC_ENET_MDIO_ENET1_MDIO 0x23
+ MX8MQ_IOMUXC_ENET_TD3_ENET1_RGMII_TD3 0x1f
+ MX8MQ_IOMUXC_ENET_TD2_ENET1_RGMII_TD2 0x1f
+ MX8MQ_IOMUXC_ENET_TD1_ENET1_RGMII_TD1 0x1f
+ MX8MQ_IOMUXC_ENET_TD0_ENET1_RGMII_TD0 0x1f
+ MX8MQ_IOMUXC_ENET_RD3_ENET1_RGMII_RD3 0x91
+ MX8MQ_IOMUXC_ENET_RD2_ENET1_RGMII_RD2 0x91
+ MX8MQ_IOMUXC_ENET_RD1_ENET1_RGMII_RD1 0x91
+ MX8MQ_IOMUXC_ENET_RD0_ENET1_RGMII_RD0 0x91
+ MX8MQ_IOMUXC_ENET_TXC_ENET1_RGMII_TXC 0x1f
+ MX8MQ_IOMUXC_ENET_RXC_ENET1_RGMII_RXC 0x91
+ MX8MQ_IOMUXC_ENET_RX_CTL_ENET1_RGMII_RX_CTL 0x91
+ MX8MQ_IOMUXC_ENET_TX_CTL_ENET1_RGMII_TX_CTL 0x1f
+ MX8MQ_IOMUXC_GPIO1_IO09_GPIO1_IO9 0x19
+ >;
+ };
+
+ pinctrl_i2c1: i2c1grp {
+ fsl,pins = <
+ MX8MQ_IOMUXC_I2C1_SCL_I2C1_SCL 0x4000007f
+ MX8MQ_IOMUXC_I2C1_SDA_I2C1_SDA 0x4000007f
+ >;
+ };
+
+ pinctrl_i2c2: i2c2grp {
+ fsl,pins = <
+ MX8MQ_IOMUXC_I2C2_SCL_I2C2_SCL 0x4000007f
+ MX8MQ_IOMUXC_I2C2_SDA_I2C2_SDA 0x4000007f
+ >;
+ };
+
+ pinctrl_otg_vbus: otgvbusgrp {
+ fsl,pins = <
+ MX8MQ_IOMUXC_NAND_DQS_GPIO3_IO14 0x19 /* USB OTG VBUS Enable */
+ >;
+ };
+
+ pinctrl_pmic: pmicirq {
+ fsl,pins = <
+ MX8MQ_IOMUXC_GPIO1_IO03_GPIO1_IO3 0x41
+ >;
+ };
+
+ pinctrl_uart1: uart1grp {
+ fsl,pins = <
+ MX8MQ_IOMUXC_UART1_RXD_UART1_DCE_RX 0x49
+ MX8MQ_IOMUXC_UART1_TXD_UART1_DCE_TX 0x49
+ >;
+ };
+
+ pinctrl_uart2: uart2grp {
+ fsl,pins = <
+ MX8MQ_IOMUXC_UART2_RXD_UART2_DCE_RX 0x49
+ MX8MQ_IOMUXC_UART2_TXD_UART2_DCE_TX 0x49
+ MX8MQ_IOMUXC_UART4_RXD_UART2_DCE_CTS_B 0x49
+ MX8MQ_IOMUXC_UART4_TXD_UART2_DCE_RTS_B 0x49
+ >;
+ };
+
+ pinctrl_usdhc1: usdhc1grp {
+ fsl,pins = <
+ MX8MQ_IOMUXC_SD1_CLK_USDHC1_CLK 0x83
+ MX8MQ_IOMUXC_SD1_CMD_USDHC1_CMD 0xc3
+ MX8MQ_IOMUXC_SD1_DATA0_USDHC1_DATA0 0xc3
+ MX8MQ_IOMUXC_SD1_DATA1_USDHC1_DATA1 0xc3
+ MX8MQ_IOMUXC_SD1_DATA2_USDHC1_DATA2 0xc3
+ MX8MQ_IOMUXC_SD1_DATA3_USDHC1_DATA3 0xc3
+ MX8MQ_IOMUXC_SD1_DATA4_USDHC1_DATA4 0xc3
+ MX8MQ_IOMUXC_SD1_DATA5_USDHC1_DATA5 0xc3
+ MX8MQ_IOMUXC_SD1_DATA6_USDHC1_DATA6 0xc3
+ MX8MQ_IOMUXC_SD1_DATA7_USDHC1_DATA7 0xc3
+ MX8MQ_IOMUXC_SD1_STROBE_USDHC1_STROBE 0x83
+ >;
+ };
+
+ pinctrl_usdhc1_100mhz: usdhc1grp100mhz {
+ fsl,pins = <
+ MX8MQ_IOMUXC_SD1_CLK_USDHC1_CLK 0x85
+ MX8MQ_IOMUXC_SD1_CMD_USDHC1_CMD 0xc5
+ MX8MQ_IOMUXC_SD1_DATA0_USDHC1_DATA0 0xc5
+ MX8MQ_IOMUXC_SD1_DATA1_USDHC1_DATA1 0xc5
+ MX8MQ_IOMUXC_SD1_DATA2_USDHC1_DATA2 0xc5
+ MX8MQ_IOMUXC_SD1_DATA3_USDHC1_DATA3 0xc5
+ MX8MQ_IOMUXC_SD1_DATA4_USDHC1_DATA4 0xc5
+ MX8MQ_IOMUXC_SD1_DATA5_USDHC1_DATA5 0xc5
+ MX8MQ_IOMUXC_SD1_DATA6_USDHC1_DATA6 0xc5
+ MX8MQ_IOMUXC_SD1_DATA7_USDHC1_DATA7 0xc5
+ MX8MQ_IOMUXC_SD1_STROBE_USDHC1_STROBE 0x85
+ >;
+ };
+
+ pinctrl_usdhc1_200mhz: usdhc1grp200mhz {
+ fsl,pins = <
+ MX8MQ_IOMUXC_SD1_CLK_USDHC1_CLK 0x87
+ MX8MQ_IOMUXC_SD1_CMD_USDHC1_CMD 0xc7
+ MX8MQ_IOMUXC_SD1_DATA0_USDHC1_DATA0 0xc7
+ MX8MQ_IOMUXC_SD1_DATA1_USDHC1_DATA1 0xc7
+ MX8MQ_IOMUXC_SD1_DATA2_USDHC1_DATA2 0xc7
+ MX8MQ_IOMUXC_SD1_DATA3_USDHC1_DATA3 0xc7
+ MX8MQ_IOMUXC_SD1_DATA4_USDHC1_DATA4 0xc7
+ MX8MQ_IOMUXC_SD1_DATA5_USDHC1_DATA5 0xc7
+ MX8MQ_IOMUXC_SD1_DATA6_USDHC1_DATA6 0xc7
+ MX8MQ_IOMUXC_SD1_DATA7_USDHC1_DATA7 0xc7
+ MX8MQ_IOMUXC_SD1_STROBE_USDHC1_STROBE 0x87
+ >;
+ };
+
+ pinctrl_usdhc2_gpio: usdhc2grpgpio {
+ fsl,pins = <
+ MX8MQ_IOMUXC_SD2_CD_B_GPIO2_IO12 0x41
+ >;
+ };
+
+ pinctrl_usdhc2: usdhc2grp {
+ fsl,pins = <
+ MX8MQ_IOMUXC_SD2_CLK_USDHC2_CLK 0x83
+ MX8MQ_IOMUXC_SD2_CMD_USDHC2_CMD 0xc3
+ MX8MQ_IOMUXC_SD2_DATA0_USDHC2_DATA0 0xc3
+ MX8MQ_IOMUXC_SD2_DATA1_USDHC2_DATA1 0xc3
+ MX8MQ_IOMUXC_SD2_DATA2_USDHC2_DATA2 0xc3
+ MX8MQ_IOMUXC_SD2_DATA3_USDHC2_DATA3 0xc3
+ MX8MQ_IOMUXC_GPIO1_IO04_USDHC2_VSELECT 0xc1
+ >;
+ };
+
+ pinctrl_usdhc2_100mhz: usdhc2grp100mhz {
+ fsl,pins = <
+ MX8MQ_IOMUXC_SD2_CLK_USDHC2_CLK 0x85
+ MX8MQ_IOMUXC_SD2_CMD_USDHC2_CMD 0xc5
+ MX8MQ_IOMUXC_SD2_DATA0_USDHC2_DATA0 0xc5
+ MX8MQ_IOMUXC_SD2_DATA1_USDHC2_DATA1 0xc5
+ MX8MQ_IOMUXC_SD2_DATA2_USDHC2_DATA2 0xc5
+ MX8MQ_IOMUXC_SD2_DATA3_USDHC2_DATA3 0xc5
+ MX8MQ_IOMUXC_GPIO1_IO04_USDHC2_VSELECT 0xc1
+ >;
+ };
+
+ pinctrl_usdhc2_200mhz: usdhc2grp200mhz {
+ fsl,pins = <
+ MX8MQ_IOMUXC_SD2_CLK_USDHC2_CLK 0x87
+ MX8MQ_IOMUXC_SD2_CMD_USDHC2_CMD 0xc7
+ MX8MQ_IOMUXC_SD2_DATA0_USDHC2_DATA0 0xc7
+ MX8MQ_IOMUXC_SD2_DATA1_USDHC2_DATA1 0xc7
+ MX8MQ_IOMUXC_SD2_DATA2_USDHC2_DATA2 0xc7
+ MX8MQ_IOMUXC_SD2_DATA3_USDHC2_DATA3 0xc7
+ MX8MQ_IOMUXC_GPIO1_IO04_USDHC2_VSELECT 0xc1
+ >;
+ };
+
+ pinctrl_wdog: wdoggrp {
+ fsl,pins = <
+ MX8MQ_IOMUXC_GPIO1_IO02_WDOG1_WDOG_B 0xc6
+ >;
+ };
+};
+
+&fec1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_fec1 &pinctrl_enet_3v3>;
+ phy-mode = "rgmii-id";
+ pinctrl-assert-gpios = <&gpio1 0 GPIO_ACTIVE_HIGH>;
+ phy-handle = <ðphy0>;
+ fsl,magic-packet;
+ status = "okay";
+
+ mdio {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ ethphy0: ethernet-phy@1 {
+ compatible = "ethernet-phy-ieee802.3-c22";
+ reg = <1>;
+ at803x,led-act-blind-workaround;
+ at803x,eee-disabled;
+ };
+ };
+};
+
+&i2c1 {
+ clock-frequency = <100000>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_i2c1>;
+ status = "okay";
+
+ pmic: pmic@4b {
+ reg = <0x4b>;
+ compatible = "rohm,bd71837";
+ /* PMIC BD71837 PMIC_nINT GPIO1_IO12 */
+ pinctrl-0 = <&pinctrl_pmic>;
+ gpio_intr = <&gpio1 3 GPIO_ACTIVE_LOW>;
+
+ regulators {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ buck1: BUCK1 {
+ regulator-name = "buck1";
+ regulator-min-microvolt = <700000>;
+ regulator-max-microvolt = <1300000>;
+ regulator-boot-on;
+ regulator-ramp-delay = <1250>;
+ rohm,dvs-run-voltage = <900000>;
+ rohm,dvs-idle-voltage = <850000>;
+ rohm,dvs-suspend-voltage = <800000>;
+ };
+
+ buck2: BUCK2 {
+ regulator-name = "buck2";
+ regulator-min-microvolt = <700000>;
+ regulator-max-microvolt = <1300000>;
+ regulator-boot-on;
+ regulator-ramp-delay = <1250>;
+ rohm,dvs-run-voltage = <1000000>;
+ rohm,dvs-idle-voltage = <900000>;
+ };
+
+ buck3: BUCK3 {
+ regulator-name = "buck3";
+ regulator-min-microvolt = <700000>;
+ regulator-max-microvolt = <1300000>;
+ regulator-boot-on;
+ rohm,dvs-run-voltage = <1000000>;
+ };
+
+ buck4: BUCK4 {
+ regulator-name = "buck4";
+ regulator-min-microvolt = <700000>;
+ regulator-max-microvolt = <1300000>;
+ regulator-boot-on;
+ rohm,dvs-run-voltage = <1000000>;
+ };
+
+ buck5: BUCK5 {
+ regulator-name = "buck5";
+ regulator-min-microvolt = <700000>;
+ regulator-max-microvolt = <1350000>;
+ regulator-boot-on;
+ };
+
+ buck6: BUCK6 {
+ regulator-name = "buck6";
+ regulator-min-microvolt = <3000000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-boot-on;
+ };
+
+ buck7: BUCK7 {
+ regulator-name = "buck7";
+ regulator-min-microvolt = <1605000>;
+ regulator-max-microvolt = <1995000>;
+ regulator-boot-on;
+ };
+
+ buck8: BUCK8 {
+ regulator-name = "buck8";
+ regulator-min-microvolt = <800000>;
+ regulator-max-microvolt = <1400000>;
+ regulator-boot-on;
+ };
+
+ ldo1: LDO1 {
+ regulator-name = "ldo1";
+ regulator-min-microvolt = <3000000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ ldo2: LDO2 {
+ regulator-name = "ldo2";
+ regulator-min-microvolt = <900000>;
+ regulator-max-microvolt = <900000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ ldo3: LDO3 {
+ regulator-name = "ldo3";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-boot-on;
+ };
+
+ ldo4: LDO4 {
+ regulator-name = "ldo4";
+ regulator-min-microvolt = <900000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-boot-on;
+ };
+
+ ldo5: LDO5 {
+ regulator-name = "ldo5";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-boot-on;
+ };
+
+ ldo6: LDO6 {
+ regulator-name = "ldo6";
+ regulator-min-microvolt = <900000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-boot-on;
+ };
+
+ ldo7: LDO7 {
+ regulator-name = "ldo7";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-boot-on;
+ };
+ };
+ };
+};
+
+&i2c2 {
+ clock-frequency = <100000>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_i2c2>;
+ status = "okay";
+};
+
+&uart1 { /* console */
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_uart1>;
+ status = "okay";
+};
+
+&usdhc1 {
+ pinctrl-names = "default", "state_100mhz", "state_200mhz";
+ pinctrl-0 = <&pinctrl_usdhc1>;
+ pinctrl-1 = <&pinctrl_usdhc1_100mhz>;
+ pinctrl-2 = <&pinctrl_usdhc1_200mhz>;
+ bus-width = <8>;
+ non-removable;
+ status = "okay";
+};
+
+&usdhc2 {
+ pinctrl-names = "default", "state_100mhz", "state_200mhz";
+ pinctrl-0 = <&pinctrl_usdhc2>, <&pinctrl_usdhc2_gpio>;
+ pinctrl-1 = <&pinctrl_usdhc2_100mhz>, <&pinctrl_usdhc2_gpio>;
+ pinctrl-2 = <&pinctrl_usdhc2_200mhz>, <&pinctrl_usdhc2_gpio>;
+ bus-width = <4>;
+ cd-gpios = <&gpio2 12 GPIO_ACTIVE_LOW>;
+ status = "okay";
+};
+
+&usb3_phy0 {
+ status = "okay";
+};
+
+&usb3_phy1 {
+ status = "okay";
+};
+
+&usb_dwc3_1 {
+ dr_mode = "host";
+ status = "okay";
+};
+
+&wdog1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_wdog>;
+ fsl,ext-reset-output;
+ status = "okay";
+};
+
+&A53_0 {
+ operating-points = <
+ /* kHz uV */
+ 1500000 1000000
+ 1300000 1000000
+ 1000000 900000
+ 800000 900000
+ >;
+};
--
2.11.0
^ permalink raw reply related [flat|nested] 5+ messages in thread
* [PATCH v3 2/2] dt-bindings: arm: fsl: Add the pico-pi-imx8m board
2019-07-18 12:16 [PATCH v3 0/2] Add basic support for pico-pi-imx8m Andra Danciu
2019-07-18 12:16 ` [PATCH v3 1/2] arm64: dts: fsl: pico-pi: Add a device tree for the PICO-PI-IMX8M Andra Danciu
@ 2019-07-18 12:16 ` Andra Danciu
1 sibling, 0 replies; 5+ messages in thread
From: Andra Danciu @ 2019-07-18 12:16 UTC (permalink / raw)
To: shawnguo
Cc: robh+dt, mark.rutland, manivannan.sadhasivam, andrew.smirnov,
u.kleine-koenig, aisheng.dong, andradanciu1997, leoyang.li,
festevam, sriram.dash, l.stach, pankaj.bansal, ping.bai,
pramod.kumar_1, bhaskar.upadhaya, richard.hu, devicetree,
linux-kernel
Add an entry for TechNexion PICO-PI-IMX8M board based on i.MX8MQ SoC
Cc: Daniel Baluta <daniel.baluta@nxp.com>
Signed-off-by: Andra Danciu <andradanciu1997@gmail.com>
---
Documentation/devicetree/bindings/arm/fsl.yaml | 1 +
1 file changed, 1 insertion(+)
diff --git a/Documentation/devicetree/bindings/arm/fsl.yaml b/Documentation/devicetree/bindings/arm/fsl.yaml
index 7294ac36f4c0..54c094341121 100644
--- a/Documentation/devicetree/bindings/arm/fsl.yaml
+++ b/Documentation/devicetree/bindings/arm/fsl.yaml
@@ -219,6 +219,7 @@ properties:
- enum:
- fsl,imx8mq-evk # i.MX8MQ EVK Board
- purism,librem5-devkit # Purism Librem5 devkit
+ - technexion,pico-pi-imx8m # TechNexion PICO-PI-8M evk
- const: fsl,imx8mq
- description: i.MX8QXP based Boards
--
2.11.0
^ permalink raw reply related [flat|nested] 5+ messages in thread
* Re: [PATCH v3 1/2] arm64: dts: fsl: pico-pi: Add a device tree for the PICO-PI-IMX8M
2019-07-18 12:16 ` [PATCH v3 1/2] arm64: dts: fsl: pico-pi: Add a device tree for the PICO-PI-IMX8M Andra Danciu
@ 2019-07-18 23:05 ` Fabio Estevam
2019-07-19 10:20 ` Andra Danciu
0 siblings, 1 reply; 5+ messages in thread
From: Fabio Estevam @ 2019-07-18 23:05 UTC (permalink / raw)
To: Andra Danciu
Cc: Shawn Guo, Rob Herring, Mark Rutland, Manivannan Sadhasivam,
Andrey Smirnov, Uwe Kleine-König, Dong Aisheng, Li Yang,
sriram.dash, Lucas Stach, pankaj.bansal, Ping Bai, Pramod Kumar,
Bhaskar Upadhaya, Richard Hu,
open list:OPEN FIRMWARE AND FLATTENED DEVICE TREE BINDINGS,
linux-kernel
Hi Andra,
On Thu, Jul 18, 2019 at 9:16 AM Andra Danciu <andradanciu1997@gmail.com> wrote:
>
> From: Richard Hu <richard.hu@technexion.com>
Please put a few words about the board and a link to its webpage, if available.
> The current level of support yields a working console and is able to boot
> userspace from NFS or init ramdisk.
>
> Additional subsystems that are active :
> - Ethernet
> - USB
>
> Cc: Daniel Baluta <daniel.baluta@nxp.com>
> Signed-off-by: Richard Hu <richard.hu@technexion.com>
> Signed-off-by: Andra Danciu <andradanciu1997@gmail.com>
> ---
> arch/arm64/boot/dts/freescale/Makefile | 1 +
> arch/arm64/boot/dts/freescale/pico-pi-8m.dts | 417 +++++++++++++++++++++++++++
> 2 files changed, 418 insertions(+)
> create mode 100644 arch/arm64/boot/dts/freescale/pico-pi-8m.dts
>
> diff --git a/arch/arm64/boot/dts/freescale/Makefile b/arch/arm64/boot/dts/freescale/Makefile
> index c043aca66572..538422903e8a 100644
> --- a/arch/arm64/boot/dts/freescale/Makefile
> +++ b/arch/arm64/boot/dts/freescale/Makefile
> @@ -26,3 +26,4 @@ dtb-$(CONFIG_ARCH_MXC) += imx8mq-librem5-devkit.dtb
> dtb-$(CONFIG_ARCH_MXC) += imx8mq-zii-ultra-rmb3.dtb
> dtb-$(CONFIG_ARCH_MXC) += imx8mq-zii-ultra-zest.dtb
> dtb-$(CONFIG_ARCH_MXC) += imx8qxp-mek.dtb
> +dtb-$(CONFIG_ARCH_MXC) += pico-pi-8m.dtb
The convention we use with imx dtbs is to put the SoC name first, so
that would become:
imx8mq-pico-pi.dtb
> +&iomuxc {
Please place iomuxc node as the last one.
> +&fec1 {
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_fec1 &pinctrl_enet_3v3>;
> + phy-mode = "rgmii-id";
> + pinctrl-assert-gpios = <&gpio1 0 GPIO_ACTIVE_HIGH>;
This property does not exist.
> + phy-handle = <ðphy0>;
> + fsl,magic-packet;
> + status = "okay";
> +
> + mdio {
> + #address-cells = <1>;
> + #size-cells = <0>;
> +
> + ethphy0: ethernet-phy@1 {
> + compatible = "ethernet-phy-ieee802.3-c22";
> + reg = <1>;
> + at803x,led-act-blind-workaround;
> + at803x,eee-disabled;
These two properties do not exist.
> +&i2c1 {
> + clock-frequency = <100000>;
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_i2c1>;
> + status = "okay";
> +
> + pmic: pmic@4b {
> + reg = <0x4b>;
> + compatible = "rohm,bd71837";
> + /* PMIC BD71837 PMIC_nINT GPIO1_IO12 */
> + pinctrl-0 = <&pinctrl_pmic>;
pinctrl-names = "default" is missing
> + gpio_intr = <&gpio1 3 GPIO_ACTIVE_LOW>;
This is not documented.
Please look at Documentation/devicetree/bindings/regulator/rohm,bd71837-regulator.txt
for the valid bindings and also at
arch/arm64/boot/dts/freescale/imx8mq-librem5-devkit.dts for a
reference for adding the BD71837 support.
> +&A53_0 {
> + operating-points = <
> + /* kHz uV */
> + 1500000 1000000
> + 1300000 1000000
> + 1000000 900000
> + 800000 900000
This is not needed as these operating points are already specified at
imx8mq.dtsi.
^ permalink raw reply [flat|nested] 5+ messages in thread
* Re: [PATCH v3 1/2] arm64: dts: fsl: pico-pi: Add a device tree for the PICO-PI-IMX8M
2019-07-18 23:05 ` Fabio Estevam
@ 2019-07-19 10:20 ` Andra Danciu
0 siblings, 0 replies; 5+ messages in thread
From: Andra Danciu @ 2019-07-19 10:20 UTC (permalink / raw)
To: Fabio Estevam
Cc: Shawn Guo, Rob Herring, Mark Rutland, Manivannan Sadhasivam,
Andrey Smirnov, Uwe Kleine-König, Dong Aisheng, Li Yang,
sriram.dash, Lucas Stach, pankaj.bansal, Ping Bai, Pramod Kumar,
Bhaskar Upadhaya, Richard Hu,
open list:OPEN FIRMWARE AND FLATTENED DEVICE TREE BINDINGS,
linux-kernel
Hi Fabio,
Please find my answers inline:
În vin., 19 iul. 2019 la 02:05, Fabio Estevam <festevam@gmail.com> a scris:
>
> Hi Andra,
>
> On Thu, Jul 18, 2019 at 9:16 AM Andra Danciu <andradanciu1997@gmail.com> wrote:
> >
> > From: Richard Hu <richard.hu@technexion.com>
>
> Please put a few words about the board and a link to its webpage, if available.
OK
>
> > The current level of support yields a working console and is able to boot
> > userspace from NFS or init ramdisk.
> >
> > Additional subsystems that are active :
> > - Ethernet
> > - USB
> >
> > Cc: Daniel Baluta <daniel.baluta@nxp.com>
> > Signed-off-by: Richard Hu <richard.hu@technexion.com>
> > Signed-off-by: Andra Danciu <andradanciu1997@gmail.com>
> > ---
> > arch/arm64/boot/dts/freescale/Makefile | 1 +
> > arch/arm64/boot/dts/freescale/pico-pi-8m.dts | 417 +++++++++++++++++++++++++++
> > 2 files changed, 418 insertions(+)
> > create mode 100644 arch/arm64/boot/dts/freescale/pico-pi-8m.dts
> >
> > diff --git a/arch/arm64/boot/dts/freescale/Makefile b/arch/arm64/boot/dts/freescale/Makefile
> > index c043aca66572..538422903e8a 100644
> > --- a/arch/arm64/boot/dts/freescale/Makefile
> > +++ b/arch/arm64/boot/dts/freescale/Makefile
> > @@ -26,3 +26,4 @@ dtb-$(CONFIG_ARCH_MXC) += imx8mq-librem5-devkit.dtb
> > dtb-$(CONFIG_ARCH_MXC) += imx8mq-zii-ultra-rmb3.dtb
> > dtb-$(CONFIG_ARCH_MXC) += imx8mq-zii-ultra-zest.dtb
> > dtb-$(CONFIG_ARCH_MXC) += imx8qxp-mek.dtb
> > +dtb-$(CONFIG_ARCH_MXC) += pico-pi-8m.dtb
>
> The convention we use with imx dtbs is to put the SoC name first, so
> that would become:
>
> imx8mq-pico-pi.dtb
Will do.
>
>
> > +&iomuxc {
>
> Please place iomuxc node as the last one.
Will do.
>
> > +&fec1 {
> > + pinctrl-names = "default";
> > + pinctrl-0 = <&pinctrl_fec1 &pinctrl_enet_3v3>;
> > + phy-mode = "rgmii-id";
> > + pinctrl-assert-gpios = <&gpio1 0 GPIO_ACTIVE_HIGH>;
>
> This property does not exist.
OK, I will remove it.
>
> > + phy-handle = <ðphy0>;
> > + fsl,magic-packet;
> > + status = "okay";
> > +
> > + mdio {
> > + #address-cells = <1>;
> > + #size-cells = <0>;
> > +
> > + ethphy0: ethernet-phy@1 {
> > + compatible = "ethernet-phy-ieee802.3-c22";
> > + reg = <1>;
> > + at803x,led-act-blind-workaround;
> > + at803x,eee-disabled;
>
> These two properties do not exist.
OK, I will remove them.
>
> > +&i2c1 {
> > + clock-frequency = <100000>;
> > + pinctrl-names = "default";
> > + pinctrl-0 = <&pinctrl_i2c1>;
> > + status = "okay";
> > +
> > + pmic: pmic@4b {
> > + reg = <0x4b>;
> > + compatible = "rohm,bd71837";
> > + /* PMIC BD71837 PMIC_nINT GPIO1_IO12 */
> > + pinctrl-0 = <&pinctrl_pmic>;
>
> pinctrl-names = "default" is missing
OK, will add.
>
> > + gpio_intr = <&gpio1 3 GPIO_ACTIVE_LOW>;
>
> This is not documented.
>
> Please look at Documentation/devicetree/bindings/regulator/rohm,bd71837-regulator.txt
> for the valid bindings and also at
> arch/arm64/boot/dts/freescale/imx8mq-librem5-devkit.dts for a
> reference for adding the BD71837 support.
OK, will do.
>
> > +&A53_0 {
> > + operating-points = <
> > + /* kHz uV */
> > + 1500000 1000000
> > + 1300000 1000000
> > + 1000000 900000
> > + 800000 900000
>
> This is not needed as these operating points are already specified at
> imx8mq.dtsi.
OK, I will remove it.
^ permalink raw reply [flat|nested] 5+ messages in thread
end of thread, other threads:[~2019-07-19 10:20 UTC | newest]
Thread overview: 5+ messages (download: mbox.gz / follow: Atom feed)
-- links below jump to the message on this page --
2019-07-18 12:16 [PATCH v3 0/2] Add basic support for pico-pi-imx8m Andra Danciu
2019-07-18 12:16 ` [PATCH v3 1/2] arm64: dts: fsl: pico-pi: Add a device tree for the PICO-PI-IMX8M Andra Danciu
2019-07-18 23:05 ` Fabio Estevam
2019-07-19 10:20 ` Andra Danciu
2019-07-18 12:16 ` [PATCH v3 2/2] dt-bindings: arm: fsl: Add the pico-pi-imx8m board Andra Danciu
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).