* [PATCH v6 0/2] Add basic support for pico-pi-imx8m
@ 2019-07-22 10:27 andradanciu1997
2019-07-22 10:27 ` [PATCH v6 1/2] arm64: dts: fsl: pico-pi: Add a device tree for the PICO-PI-IMX8M andradanciu1997
` (2 more replies)
0 siblings, 3 replies; 4+ messages in thread
From: andradanciu1997 @ 2019-07-22 10:27 UTC (permalink / raw)
To: shawnguo
Cc: robh+dt, mark.rutland, s.hauer, kernel, festevam, linux-imx,
manivannan.sadhasivam, andrew.smirnov, Michal.Vokac, ping.bai,
u.kleine-koenig, leoyang.li, aisheng.dong, l.stach,
pankaj.bansal, angus, pramod.kumar_1, bhaskar.upadhaya,
vabhav.sharma, andradanciu1997, richard.hu, devicetree,
linux-kernel, linux-arm-kernel
Add support for TechNexion PICO-PI-IMX8M based on patches from Richard Hu
Datasheet is at: https://s3.us-east-2.amazonaws.com/technexion/datasheets/picopiimx8m.pdf
Changes since v5:
- removed comment /* PMIC BD71837 PMIC_nINT GPIO1_IO12 */
- added "Reviewed-by" tags
Changes since v4:
- removed #address-cells and #size-cells from regulators node
Changes since v3:
- renamed pico-pi-8m.dts to imx8mq-pico-pi.dts
- moved iomuxc node as the last one
- removed pinctrl-assert-gpios property from fec1 node
- removed at803x,led-act-blind-workaround, at803x,eee-disabled
properties from mdio node
- added pinctrl-names = "default" to i2c1 node
- changed bd71837 pmic support properties according to
Documentation/devicetree/bindings/regulator/rohm,bd71837-regulator.txt
- removed A53_0 node
Changes since v2:
- changed PICO-PI-8M bord compatible from wand,imx8mq-pico-pi to
technexion,pico-pi-imx8m
- removed bootargs property
- removed regulators node and put fixed regulator directly under root node
- changed node name from usb_otg_vbus to regulator-usb-otg-vbus
- removed pinctrl-names property from iomuxc node
- removed wand-pi-8m container node
- sorted pinctrl nodes alphabetically
- removed tusb320_irqgrp, tusb320_irqgrp nodes because there is no upstream
driver
- changed properties' order in usb_dwc3_1 node
Changes since v1:
- renamed wandboard-pi-8m.dts to pico-pi-8m.dts
- removed pinctrl_csi1, pinctrl_wifi_ctrl
- used generic name for pmic
- removed gpo node
- delete regulator-virtuals node
- remove always-on property from buck1-8 and ldo3-7
- remove pmic-buck-uses-i2c-dvs property for buck1-4
Andra Danciu (1):
dt-bindings: arm: fsl: Add the pico-pi-imx8m board
Richard Hu (1):
arm64: dts: fsl: pico-pi: Add a device tree for the PICO-PI-IMX8M
Documentation/devicetree/bindings/arm/fsl.yaml | 1 +
arch/arm64/boot/dts/freescale/Makefile | 1 +
arch/arm64/boot/dts/freescale/imx8mq-pico-pi.dts | 413 +++++++++++++++++++++++
3 files changed, 415 insertions(+)
create mode 100644 arch/arm64/boot/dts/freescale/imx8mq-pico-pi.dts
--
2.11.0
^ permalink raw reply [flat|nested] 4+ messages in thread
* [PATCH v6 1/2] arm64: dts: fsl: pico-pi: Add a device tree for the PICO-PI-IMX8M
2019-07-22 10:27 [PATCH v6 0/2] Add basic support for pico-pi-imx8m andradanciu1997
@ 2019-07-22 10:27 ` andradanciu1997
2019-07-22 10:27 ` [PATCH v6 2/2] dt-bindings: arm: fsl: Add the pico-pi-imx8m board andradanciu1997
2019-07-23 8:25 ` [PATCH v6 0/2] Add basic support for pico-pi-imx8m Shawn Guo
2 siblings, 0 replies; 4+ messages in thread
From: andradanciu1997 @ 2019-07-22 10:27 UTC (permalink / raw)
To: shawnguo
Cc: robh+dt, mark.rutland, s.hauer, kernel, festevam, linux-imx,
manivannan.sadhasivam, andrew.smirnov, Michal.Vokac, ping.bai,
u.kleine-koenig, leoyang.li, aisheng.dong, l.stach,
pankaj.bansal, angus, pramod.kumar_1, bhaskar.upadhaya,
vabhav.sharma, andradanciu1997, richard.hu, devicetree,
linux-kernel, linux-arm-kernel
From: Richard Hu <richard.hu@technexion.com>
TechNexion PICO-PI-IMX8M-DEV evaluation and development kit based on
NXP i.MX8M Quad applications processor. Datasheet can be found at:
https://s3.us-east-2.amazonaws.com/technexion/datasheets/picopiimx8m.pdf
The current level of support yields a working console and is able to boot
userspace from NFS or init ramdisk.
Additional subsystems that are active :
- Ethernet
- USB
Cc: Daniel Baluta <daniel.baluta@nxp.com>
Signed-off-by: Richard Hu <richard.hu@technexion.com>
Signed-off-by: Andra Danciu <andradanciu1997@gmail.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
---
arch/arm64/boot/dts/freescale/Makefile | 1 +
arch/arm64/boot/dts/freescale/imx8mq-pico-pi.dts | 413 +++++++++++++++++++++++
2 files changed, 414 insertions(+)
create mode 100644 arch/arm64/boot/dts/freescale/imx8mq-pico-pi.dts
diff --git a/arch/arm64/boot/dts/freescale/Makefile b/arch/arm64/boot/dts/freescale/Makefile
index c043aca66572..99627a499a73 100644
--- a/arch/arm64/boot/dts/freescale/Makefile
+++ b/arch/arm64/boot/dts/freescale/Makefile
@@ -23,6 +23,7 @@ dtb-$(CONFIG_ARCH_LAYERSCAPE) += fsl-lx2160a-rdb.dtb
dtb-$(CONFIG_ARCH_MXC) += imx8mm-evk.dtb
dtb-$(CONFIG_ARCH_MXC) += imx8mq-evk.dtb
dtb-$(CONFIG_ARCH_MXC) += imx8mq-librem5-devkit.dtb
+dtb-$(CONFIG_ARCH_MXC) += imx8mq-pico-pi.dtb
dtb-$(CONFIG_ARCH_MXC) += imx8mq-zii-ultra-rmb3.dtb
dtb-$(CONFIG_ARCH_MXC) += imx8mq-zii-ultra-zest.dtb
dtb-$(CONFIG_ARCH_MXC) += imx8qxp-mek.dtb
diff --git a/arch/arm64/boot/dts/freescale/imx8mq-pico-pi.dts b/arch/arm64/boot/dts/freescale/imx8mq-pico-pi.dts
new file mode 100644
index 000000000000..8a4aee2348ee
--- /dev/null
+++ b/arch/arm64/boot/dts/freescale/imx8mq-pico-pi.dts
@@ -0,0 +1,413 @@
+// SPDX-License-Identifier: GPL-2.0+
+/*
+ * Copyright 2018 Wandboard, Org.
+ * Copyright 2017 NXP
+ *
+ * Author: Richard Hu <hakahu@gmail.com>
+ */
+
+/dts-v1/;
+
+#include "imx8mq.dtsi"
+
+/ {
+ model = "TechNexion PICO-PI-8M";
+ compatible = "technexion,pico-pi-imx8m", "fsl,imx8mq";
+
+ chosen {
+ stdout-path = &uart1;
+ };
+
+ pmic_osc: clock-pmic {
+ compatible = "fixed-clock";
+ #clock-cells = <0>;
+ clock-frequency = <32768>;
+ clock-output-names = "pmic_osc";
+ };
+
+ reg_usb_otg_vbus: regulator-usb-otg-vbus {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_otg_vbus>;
+ compatible = "regulator-fixed";
+ regulator-name = "usb_otg_vbus";
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ gpio = <&gpio3 14 GPIO_ACTIVE_LOW>;
+ };
+};
+
+&fec1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_fec1 &pinctrl_enet_3v3>;
+ phy-mode = "rgmii-id";
+ phy-handle = <ðphy0>;
+ fsl,magic-packet;
+ status = "okay";
+
+ mdio {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ ethphy0: ethernet-phy@1 {
+ compatible = "ethernet-phy-ieee802.3-c22";
+ reg = <1>;
+ };
+ };
+};
+
+&i2c1 {
+ clock-frequency = <100000>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_i2c1>;
+ status = "okay";
+
+ pmic: pmic@4b {
+ reg = <0x4b>;
+ compatible = "rohm,bd71837";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_pmic>;
+ clocks = <&pmic_osc>;
+ clock-names = "osc";
+ clock-output-names = "pmic_clk";
+ interrupt-parent = <&gpio1>;
+ interrupts = <3 GPIO_ACTIVE_LOW>;
+ interrupt-names = "irq";
+
+ regulators {
+ buck1: BUCK1 {
+ regulator-name = "buck1";
+ regulator-min-microvolt = <700000>;
+ regulator-max-microvolt = <1300000>;
+ regulator-boot-on;
+ regulator-ramp-delay = <1250>;
+ rohm,dvs-run-voltage = <900000>;
+ rohm,dvs-idle-voltage = <850000>;
+ rohm,dvs-suspend-voltage = <800000>;
+ };
+
+ buck2: BUCK2 {
+ regulator-name = "buck2";
+ regulator-min-microvolt = <700000>;
+ regulator-max-microvolt = <1300000>;
+ regulator-boot-on;
+ regulator-ramp-delay = <1250>;
+ rohm,dvs-run-voltage = <1000000>;
+ rohm,dvs-idle-voltage = <900000>;
+ };
+
+ buck3: BUCK3 {
+ regulator-name = "buck3";
+ regulator-min-microvolt = <700000>;
+ regulator-max-microvolt = <1300000>;
+ regulator-boot-on;
+ rohm,dvs-run-voltage = <1000000>;
+ };
+
+ buck4: BUCK4 {
+ regulator-name = "buck4";
+ regulator-min-microvolt = <700000>;
+ regulator-max-microvolt = <1300000>;
+ regulator-boot-on;
+ rohm,dvs-run-voltage = <1000000>;
+ };
+
+ buck5: BUCK5 {
+ regulator-name = "buck5";
+ regulator-min-microvolt = <700000>;
+ regulator-max-microvolt = <1350000>;
+ regulator-boot-on;
+ };
+
+ buck6: BUCK6 {
+ regulator-name = "buck6";
+ regulator-min-microvolt = <3000000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-boot-on;
+ };
+
+ buck7: BUCK7 {
+ regulator-name = "buck7";
+ regulator-min-microvolt = <1605000>;
+ regulator-max-microvolt = <1995000>;
+ regulator-boot-on;
+ };
+
+ buck8: BUCK8 {
+ regulator-name = "buck8";
+ regulator-min-microvolt = <800000>;
+ regulator-max-microvolt = <1400000>;
+ regulator-boot-on;
+ };
+
+ ldo1: LDO1 {
+ regulator-name = "ldo1";
+ regulator-min-microvolt = <3000000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ ldo2: LDO2 {
+ regulator-name = "ldo2";
+ regulator-min-microvolt = <900000>;
+ regulator-max-microvolt = <900000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ ldo3: LDO3 {
+ regulator-name = "ldo3";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-boot-on;
+ };
+
+ ldo4: LDO4 {
+ regulator-name = "ldo4";
+ regulator-min-microvolt = <900000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-boot-on;
+ };
+
+ ldo5: LDO5 {
+ regulator-name = "ldo5";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-boot-on;
+ };
+
+ ldo6: LDO6 {
+ regulator-name = "ldo6";
+ regulator-min-microvolt = <900000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-boot-on;
+ };
+
+ ldo7: LDO7 {
+ regulator-name = "ldo7";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-boot-on;
+ };
+ };
+ };
+};
+
+&i2c2 {
+ clock-frequency = <100000>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_i2c2>;
+ status = "okay";
+};
+
+&uart1 { /* console */
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_uart1>;
+ status = "okay";
+};
+
+&usdhc1 {
+ pinctrl-names = "default", "state_100mhz", "state_200mhz";
+ pinctrl-0 = <&pinctrl_usdhc1>;
+ pinctrl-1 = <&pinctrl_usdhc1_100mhz>;
+ pinctrl-2 = <&pinctrl_usdhc1_200mhz>;
+ bus-width = <8>;
+ non-removable;
+ status = "okay";
+};
+
+&usdhc2 {
+ pinctrl-names = "default", "state_100mhz", "state_200mhz";
+ pinctrl-0 = <&pinctrl_usdhc2>, <&pinctrl_usdhc2_gpio>;
+ pinctrl-1 = <&pinctrl_usdhc2_100mhz>, <&pinctrl_usdhc2_gpio>;
+ pinctrl-2 = <&pinctrl_usdhc2_200mhz>, <&pinctrl_usdhc2_gpio>;
+ bus-width = <4>;
+ cd-gpios = <&gpio2 12 GPIO_ACTIVE_LOW>;
+ status = "okay";
+};
+
+&usb3_phy0 {
+ status = "okay";
+};
+
+&usb3_phy1 {
+ status = "okay";
+};
+
+&usb_dwc3_1 {
+ dr_mode = "host";
+ status = "okay";
+};
+
+&wdog1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_wdog>;
+ fsl,ext-reset-output;
+ status = "okay";
+};
+
+&iomuxc {
+ pinctrl_enet_3v3: enet3v3grp {
+ fsl,pins = <
+ MX8MQ_IOMUXC_GPIO1_IO00_GPIO1_IO0 0x19
+ >;
+ };
+
+ pinctrl_fec1: fec1grp {
+ fsl,pins = <
+ MX8MQ_IOMUXC_ENET_MDC_ENET1_MDC 0x3
+ MX8MQ_IOMUXC_ENET_MDIO_ENET1_MDIO 0x23
+ MX8MQ_IOMUXC_ENET_TD3_ENET1_RGMII_TD3 0x1f
+ MX8MQ_IOMUXC_ENET_TD2_ENET1_RGMII_TD2 0x1f
+ MX8MQ_IOMUXC_ENET_TD1_ENET1_RGMII_TD1 0x1f
+ MX8MQ_IOMUXC_ENET_TD0_ENET1_RGMII_TD0 0x1f
+ MX8MQ_IOMUXC_ENET_RD3_ENET1_RGMII_RD3 0x91
+ MX8MQ_IOMUXC_ENET_RD2_ENET1_RGMII_RD2 0x91
+ MX8MQ_IOMUXC_ENET_RD1_ENET1_RGMII_RD1 0x91
+ MX8MQ_IOMUXC_ENET_RD0_ENET1_RGMII_RD0 0x91
+ MX8MQ_IOMUXC_ENET_TXC_ENET1_RGMII_TXC 0x1f
+ MX8MQ_IOMUXC_ENET_RXC_ENET1_RGMII_RXC 0x91
+ MX8MQ_IOMUXC_ENET_RX_CTL_ENET1_RGMII_RX_CTL 0x91
+ MX8MQ_IOMUXC_ENET_TX_CTL_ENET1_RGMII_TX_CTL 0x1f
+ MX8MQ_IOMUXC_GPIO1_IO09_GPIO1_IO9 0x19
+ >;
+ };
+
+ pinctrl_i2c1: i2c1grp {
+ fsl,pins = <
+ MX8MQ_IOMUXC_I2C1_SCL_I2C1_SCL 0x4000007f
+ MX8MQ_IOMUXC_I2C1_SDA_I2C1_SDA 0x4000007f
+ >;
+ };
+
+ pinctrl_i2c2: i2c2grp {
+ fsl,pins = <
+ MX8MQ_IOMUXC_I2C2_SCL_I2C2_SCL 0x4000007f
+ MX8MQ_IOMUXC_I2C2_SDA_I2C2_SDA 0x4000007f
+ >;
+ };
+
+ pinctrl_otg_vbus: otgvbusgrp {
+ fsl,pins = <
+ MX8MQ_IOMUXC_NAND_DQS_GPIO3_IO14 0x19 /* USB OTG VBUS Enable */
+ >;
+ };
+
+ pinctrl_pmic: pmicirq {
+ fsl,pins = <
+ MX8MQ_IOMUXC_GPIO1_IO03_GPIO1_IO3 0x41
+ >;
+ };
+
+ pinctrl_uart1: uart1grp {
+ fsl,pins = <
+ MX8MQ_IOMUXC_UART1_RXD_UART1_DCE_RX 0x49
+ MX8MQ_IOMUXC_UART1_TXD_UART1_DCE_TX 0x49
+ >;
+ };
+
+ pinctrl_uart2: uart2grp {
+ fsl,pins = <
+ MX8MQ_IOMUXC_UART2_RXD_UART2_DCE_RX 0x49
+ MX8MQ_IOMUXC_UART2_TXD_UART2_DCE_TX 0x49
+ MX8MQ_IOMUXC_UART4_RXD_UART2_DCE_CTS_B 0x49
+ MX8MQ_IOMUXC_UART4_TXD_UART2_DCE_RTS_B 0x49
+ >;
+ };
+
+ pinctrl_usdhc1: usdhc1grp {
+ fsl,pins = <
+ MX8MQ_IOMUXC_SD1_CLK_USDHC1_CLK 0x83
+ MX8MQ_IOMUXC_SD1_CMD_USDHC1_CMD 0xc3
+ MX8MQ_IOMUXC_SD1_DATA0_USDHC1_DATA0 0xc3
+ MX8MQ_IOMUXC_SD1_DATA1_USDHC1_DATA1 0xc3
+ MX8MQ_IOMUXC_SD1_DATA2_USDHC1_DATA2 0xc3
+ MX8MQ_IOMUXC_SD1_DATA3_USDHC1_DATA3 0xc3
+ MX8MQ_IOMUXC_SD1_DATA4_USDHC1_DATA4 0xc3
+ MX8MQ_IOMUXC_SD1_DATA5_USDHC1_DATA5 0xc3
+ MX8MQ_IOMUXC_SD1_DATA6_USDHC1_DATA6 0xc3
+ MX8MQ_IOMUXC_SD1_DATA7_USDHC1_DATA7 0xc3
+ MX8MQ_IOMUXC_SD1_STROBE_USDHC1_STROBE 0x83
+ >;
+ };
+
+ pinctrl_usdhc1_100mhz: usdhc1grp100mhz {
+ fsl,pins = <
+ MX8MQ_IOMUXC_SD1_CLK_USDHC1_CLK 0x85
+ MX8MQ_IOMUXC_SD1_CMD_USDHC1_CMD 0xc5
+ MX8MQ_IOMUXC_SD1_DATA0_USDHC1_DATA0 0xc5
+ MX8MQ_IOMUXC_SD1_DATA1_USDHC1_DATA1 0xc5
+ MX8MQ_IOMUXC_SD1_DATA2_USDHC1_DATA2 0xc5
+ MX8MQ_IOMUXC_SD1_DATA3_USDHC1_DATA3 0xc5
+ MX8MQ_IOMUXC_SD1_DATA4_USDHC1_DATA4 0xc5
+ MX8MQ_IOMUXC_SD1_DATA5_USDHC1_DATA5 0xc5
+ MX8MQ_IOMUXC_SD1_DATA6_USDHC1_DATA6 0xc5
+ MX8MQ_IOMUXC_SD1_DATA7_USDHC1_DATA7 0xc5
+ MX8MQ_IOMUXC_SD1_STROBE_USDHC1_STROBE 0x85
+ >;
+ };
+
+ pinctrl_usdhc1_200mhz: usdhc1grp200mhz {
+ fsl,pins = <
+ MX8MQ_IOMUXC_SD1_CLK_USDHC1_CLK 0x87
+ MX8MQ_IOMUXC_SD1_CMD_USDHC1_CMD 0xc7
+ MX8MQ_IOMUXC_SD1_DATA0_USDHC1_DATA0 0xc7
+ MX8MQ_IOMUXC_SD1_DATA1_USDHC1_DATA1 0xc7
+ MX8MQ_IOMUXC_SD1_DATA2_USDHC1_DATA2 0xc7
+ MX8MQ_IOMUXC_SD1_DATA3_USDHC1_DATA3 0xc7
+ MX8MQ_IOMUXC_SD1_DATA4_USDHC1_DATA4 0xc7
+ MX8MQ_IOMUXC_SD1_DATA5_USDHC1_DATA5 0xc7
+ MX8MQ_IOMUXC_SD1_DATA6_USDHC1_DATA6 0xc7
+ MX8MQ_IOMUXC_SD1_DATA7_USDHC1_DATA7 0xc7
+ MX8MQ_IOMUXC_SD1_STROBE_USDHC1_STROBE 0x87
+ >;
+ };
+
+ pinctrl_usdhc2_gpio: usdhc2grpgpio {
+ fsl,pins = <
+ MX8MQ_IOMUXC_SD2_CD_B_GPIO2_IO12 0x41
+ >;
+ };
+
+ pinctrl_usdhc2: usdhc2grp {
+ fsl,pins = <
+ MX8MQ_IOMUXC_SD2_CLK_USDHC2_CLK 0x83
+ MX8MQ_IOMUXC_SD2_CMD_USDHC2_CMD 0xc3
+ MX8MQ_IOMUXC_SD2_DATA0_USDHC2_DATA0 0xc3
+ MX8MQ_IOMUXC_SD2_DATA1_USDHC2_DATA1 0xc3
+ MX8MQ_IOMUXC_SD2_DATA2_USDHC2_DATA2 0xc3
+ MX8MQ_IOMUXC_SD2_DATA3_USDHC2_DATA3 0xc3
+ MX8MQ_IOMUXC_GPIO1_IO04_USDHC2_VSELECT 0xc1
+ >;
+ };
+
+ pinctrl_usdhc2_100mhz: usdhc2grp100mhz {
+ fsl,pins = <
+ MX8MQ_IOMUXC_SD2_CLK_USDHC2_CLK 0x85
+ MX8MQ_IOMUXC_SD2_CMD_USDHC2_CMD 0xc5
+ MX8MQ_IOMUXC_SD2_DATA0_USDHC2_DATA0 0xc5
+ MX8MQ_IOMUXC_SD2_DATA1_USDHC2_DATA1 0xc5
+ MX8MQ_IOMUXC_SD2_DATA2_USDHC2_DATA2 0xc5
+ MX8MQ_IOMUXC_SD2_DATA3_USDHC2_DATA3 0xc5
+ MX8MQ_IOMUXC_GPIO1_IO04_USDHC2_VSELECT 0xc1
+ >;
+ };
+
+ pinctrl_usdhc2_200mhz: usdhc2grp200mhz {
+ fsl,pins = <
+ MX8MQ_IOMUXC_SD2_CLK_USDHC2_CLK 0x87
+ MX8MQ_IOMUXC_SD2_CMD_USDHC2_CMD 0xc7
+ MX8MQ_IOMUXC_SD2_DATA0_USDHC2_DATA0 0xc7
+ MX8MQ_IOMUXC_SD2_DATA1_USDHC2_DATA1 0xc7
+ MX8MQ_IOMUXC_SD2_DATA2_USDHC2_DATA2 0xc7
+ MX8MQ_IOMUXC_SD2_DATA3_USDHC2_DATA3 0xc7
+ MX8MQ_IOMUXC_GPIO1_IO04_USDHC2_VSELECT 0xc1
+ >;
+ };
+
+ pinctrl_wdog: wdoggrp {
+ fsl,pins = <
+ MX8MQ_IOMUXC_GPIO1_IO02_WDOG1_WDOG_B 0xc6
+ >;
+ };
+};
--
2.11.0
^ permalink raw reply related [flat|nested] 4+ messages in thread
* [PATCH v6 2/2] dt-bindings: arm: fsl: Add the pico-pi-imx8m board
2019-07-22 10:27 [PATCH v6 0/2] Add basic support for pico-pi-imx8m andradanciu1997
2019-07-22 10:27 ` [PATCH v6 1/2] arm64: dts: fsl: pico-pi: Add a device tree for the PICO-PI-IMX8M andradanciu1997
@ 2019-07-22 10:27 ` andradanciu1997
2019-07-23 8:25 ` [PATCH v6 0/2] Add basic support for pico-pi-imx8m Shawn Guo
2 siblings, 0 replies; 4+ messages in thread
From: andradanciu1997 @ 2019-07-22 10:27 UTC (permalink / raw)
To: shawnguo
Cc: robh+dt, mark.rutland, s.hauer, kernel, festevam, linux-imx,
manivannan.sadhasivam, andrew.smirnov, Michal.Vokac, ping.bai,
u.kleine-koenig, leoyang.li, aisheng.dong, l.stach,
pankaj.bansal, angus, pramod.kumar_1, bhaskar.upadhaya,
vabhav.sharma, andradanciu1997, richard.hu, devicetree,
linux-kernel, linux-arm-kernel
From: Andra Danciu <andradanciu1997@gmail.com>
Add an entry for TechNexion PICO-PI-IMX8M board based on i.MX8MQ SoC
Datasheet can be found at:
https://s3.us-east-2.amazonaws.com/technexion/datasheets/picopiimx8m.pdf
Cc: Daniel Baluta <daniel.baluta@nxp.com>
Signed-off-by: Andra Danciu <andradanciu1997@gmail.com>
Reviewed-by: Rob Herring <robh@kernel.org>
---
Documentation/devicetree/bindings/arm/fsl.yaml | 1 +
1 file changed, 1 insertion(+)
diff --git a/Documentation/devicetree/bindings/arm/fsl.yaml b/Documentation/devicetree/bindings/arm/fsl.yaml
index 7294ac36f4c0..54c094341121 100644
--- a/Documentation/devicetree/bindings/arm/fsl.yaml
+++ b/Documentation/devicetree/bindings/arm/fsl.yaml
@@ -219,6 +219,7 @@ properties:
- enum:
- fsl,imx8mq-evk # i.MX8MQ EVK Board
- purism,librem5-devkit # Purism Librem5 devkit
+ - technexion,pico-pi-imx8m # TechNexion PICO-PI-8M evk
- const: fsl,imx8mq
- description: i.MX8QXP based Boards
--
2.11.0
^ permalink raw reply related [flat|nested] 4+ messages in thread
* Re: [PATCH v6 0/2] Add basic support for pico-pi-imx8m
2019-07-22 10:27 [PATCH v6 0/2] Add basic support for pico-pi-imx8m andradanciu1997
2019-07-22 10:27 ` [PATCH v6 1/2] arm64: dts: fsl: pico-pi: Add a device tree for the PICO-PI-IMX8M andradanciu1997
2019-07-22 10:27 ` [PATCH v6 2/2] dt-bindings: arm: fsl: Add the pico-pi-imx8m board andradanciu1997
@ 2019-07-23 8:25 ` Shawn Guo
2 siblings, 0 replies; 4+ messages in thread
From: Shawn Guo @ 2019-07-23 8:25 UTC (permalink / raw)
To: andradanciu1997
Cc: robh+dt, mark.rutland, s.hauer, kernel, festevam, linux-imx,
manivannan.sadhasivam, andrew.smirnov, Michal.Vokac, ping.bai,
u.kleine-koenig, leoyang.li, aisheng.dong, l.stach,
pankaj.bansal, angus, pramod.kumar_1, bhaskar.upadhaya,
vabhav.sharma, richard.hu, devicetree, linux-kernel,
linux-arm-kernel
On Mon, Jul 22, 2019 at 01:27:28PM +0300, andradanciu1997 wrote:
> Add support for TechNexion PICO-PI-IMX8M based on patches from Richard Hu
> Datasheet is at: https://s3.us-east-2.amazonaws.com/technexion/datasheets/picopiimx8m.pdf
>
> Changes since v5:
> - removed comment /* PMIC BD71837 PMIC_nINT GPIO1_IO12 */
> - added "Reviewed-by" tags
>
> Changes since v4:
> - removed #address-cells and #size-cells from regulators node
>
> Changes since v3:
> - renamed pico-pi-8m.dts to imx8mq-pico-pi.dts
> - moved iomuxc node as the last one
> - removed pinctrl-assert-gpios property from fec1 node
> - removed at803x,led-act-blind-workaround, at803x,eee-disabled
> properties from mdio node
> - added pinctrl-names = "default" to i2c1 node
> - changed bd71837 pmic support properties according to
> Documentation/devicetree/bindings/regulator/rohm,bd71837-regulator.txt
> - removed A53_0 node
>
> Changes since v2:
> - changed PICO-PI-8M bord compatible from wand,imx8mq-pico-pi to
> technexion,pico-pi-imx8m
> - removed bootargs property
> - removed regulators node and put fixed regulator directly under root node
> - changed node name from usb_otg_vbus to regulator-usb-otg-vbus
> - removed pinctrl-names property from iomuxc node
> - removed wand-pi-8m container node
> - sorted pinctrl nodes alphabetically
> - removed tusb320_irqgrp, tusb320_irqgrp nodes because there is no upstream
> driver
> - changed properties' order in usb_dwc3_1 node
>
> Changes since v1:
> - renamed wandboard-pi-8m.dts to pico-pi-8m.dts
> - removed pinctrl_csi1, pinctrl_wifi_ctrl
> - used generic name for pmic
> - removed gpo node
> - delete regulator-virtuals node
> - remove always-on property from buck1-8 and ldo3-7
> - remove pmic-buck-uses-i2c-dvs property for buck1-4
>
> Andra Danciu (1):
> dt-bindings: arm: fsl: Add the pico-pi-imx8m board
>
> Richard Hu (1):
> arm64: dts: fsl: pico-pi: Add a device tree for the PICO-PI-IMX8M
Applied both, thanks.
^ permalink raw reply [flat|nested] 4+ messages in thread
end of thread, other threads:[~2019-07-23 8:25 UTC | newest]
Thread overview: 4+ messages (download: mbox.gz / follow: Atom feed)
-- links below jump to the message on this page --
2019-07-22 10:27 [PATCH v6 0/2] Add basic support for pico-pi-imx8m andradanciu1997
2019-07-22 10:27 ` [PATCH v6 1/2] arm64: dts: fsl: pico-pi: Add a device tree for the PICO-PI-IMX8M andradanciu1997
2019-07-22 10:27 ` [PATCH v6 2/2] dt-bindings: arm: fsl: Add the pico-pi-imx8m board andradanciu1997
2019-07-23 8:25 ` [PATCH v6 0/2] Add basic support for pico-pi-imx8m Shawn Guo
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).