[PATCH AUTOSEL 4.14 030/109] ARM: dts: am335x-evm: fix number of cpsw

[PATCH AUTOSEL 4.14 030/109] ARM: dts: am335x-evm: fix number of cpsw

[Sasha Levin]

From: Grygorii Strashko <grygorii.strashko@ti.com>

[ Upstream commit dcbf6b18d81bcdc51390ca1b258c17e2e13b7d0c ]

am335x-evm has only one CPSW external port physically wired, but DT defines
2 ext. ports. As result, PHY connection failure reported for the second
ext. port.

Update DT to reflect am335x-evm board HW configuration, and, while here,
switch to use phy-handle instead of phy_id.

Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 arch/arm/boot/dts/am335x-evm.dts | 12 ++++++------
 1 file changed, 6 insertions(+), 6 deletions(-)

diff --git a/arch/arm/boot/dts/am335x-evm.dts b/arch/arm/boot/dts/am335x-evm.dts
index 478434ebff92d..27ff3e689e96e 100644
--- a/arch/arm/boot/dts/am335x-evm.dts
+++ b/arch/arm/boot/dts/am335x-evm.dts
@@ -724,6 +724,7 @@
 	pinctrl-0 = <&cpsw_default>;
 	pinctrl-1 = <&cpsw_sleep>;
 	status = "okay";
+	slaves = <1>;
 };
 
 &davinci_mdio {
@@ -731,15 +732,14 @@
 	pinctrl-0 = <&davinci_mdio_default>;
 	pinctrl-1 = <&davinci_mdio_sleep>;
 	status = "okay";
-};
 
-&cpsw_emac0 {
-	phy_id = <&davinci_mdio>, <0>;
-	phy-mode = "rgmii-txid";
+	ethphy0: ethernet-phy@0 {
+		reg = <0>;
+	};
 };
 
-&cpsw_emac1 {
-	phy_id = <&davinci_mdio>, <1>;
+&cpsw_emac0 {
+	phy-handle = <&ethphy0>;
 	phy-mode = "rgmii-txid";
 };
 
-- 
2.20.1

[PATCH AUTOSEL 4.14 032/109] ARM: dts: ux500: Correct SCU unit address

[Sasha Levin]

From: Geert Uytterhoeven <geert+renesas@glider.be>

[ Upstream commit 2f217d24ecaec2012e628d21e244eef0608656a4 ]

The unit address of the Cortex-A9 SCU device node contains one zero too
many.  Remove it.

Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 arch/arm/boot/dts/ste-dbx5x0.dtsi | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)

diff --git a/arch/arm/boot/dts/ste-dbx5x0.dtsi b/arch/arm/boot/dts/ste-dbx5x0.dtsi
index 2310a4e97768c..3dc0028e108b3 100644
--- a/arch/arm/boot/dts/ste-dbx5x0.dtsi
+++ b/arch/arm/boot/dts/ste-dbx5x0.dtsi
@@ -197,7 +197,7 @@
 			      <0xa0410100 0x100>;
 		};
 
-		scu@a04100000 {
+		scu@a0410000 {
 			compatible = "arm,cortex-a9-scu";
 			reg = <0xa0410000 0x100>;
 		};
-- 
2.20.1

[PATCH AUTOSEL 4.14 033/109] ARM: dts: ux500: Fix LCDA clock line muxing

[Sasha Levin]

From: Linus Walleij <linus.walleij@linaro.org>

[ Upstream commit ecde29569e3484e1d0a032bf4074449bce4d4a03 ]

The "lcdaclk_b_1" group is muxed with the function "lcd"
but needs a separate entry to be muxed in with "lcda"
rather than "lcd".

Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 arch/arm/boot/dts/ste-href-family-pinctrl.dtsi | 8 ++++++--
 1 file changed, 6 insertions(+), 2 deletions(-)

diff --git a/arch/arm/boot/dts/ste-href-family-pinctrl.dtsi b/arch/arm/boot/dts/ste-href-family-pinctrl.dtsi
index 5c5cea232743d..1ec193b0c5065 100644
--- a/arch/arm/boot/dts/ste-href-family-pinctrl.dtsi
+++ b/arch/arm/boot/dts/ste-href-family-pinctrl.dtsi
@@ -607,16 +607,20 @@
 
 			mcde {
 				lcd_default_mode: lcd_default {
-					default_mux {
+					default_mux1 {
 						/* Mux in VSI0 and all the data lines */
 						function = "lcd";
 						groups =
 						"lcdvsi0_a_1", /* VSI0 for LCD */
 						"lcd_d0_d7_a_1", /* Data lines */
 						"lcd_d8_d11_a_1", /* TV-out */
-						"lcdaclk_b_1", /* Clock line for TV-out */
 						"lcdvsi1_a_1"; /* VSI1 for HDMI */
 					};
+					default_mux2 {
+						function = "lcda";
+						groups =
+						"lcdaclk_b_1"; /* Clock line for TV-out */
+					};
 					default_cfg1 {
 						pins =
 						"GPIO68_E1", /* VSI0 */
-- 
2.20.1

[PATCH AUTOSEL 4.14 034/109] ARM: dts: ste: Fix SPI controller node names

[Sasha Levin]

From: Rob Herring <robh@kernel.org>

[ Upstream commit 2f967f9e9fa076affb711da1a8389b5d33814fc6 ]

SPI controller nodes should be named 'spi' rather than 'ssp'. Fixing the
name enables dtc SPI bus checks.

Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 arch/arm/boot/dts/ste-dbx5x0.dtsi     | 4 ++--
 arch/arm/boot/dts/ste-hrefprev60.dtsi | 2 +-
 arch/arm/boot/dts/ste-snowball.dts    | 2 +-
 arch/arm/boot/dts/ste-u300.dts        | 2 +-
 4 files changed, 5 insertions(+), 5 deletions(-)

diff --git a/arch/arm/boot/dts/ste-dbx5x0.dtsi b/arch/arm/boot/dts/ste-dbx5x0.dtsi
index 3dc0028e108b3..986767735e249 100644
--- a/arch/arm/boot/dts/ste-dbx5x0.dtsi
+++ b/arch/arm/boot/dts/ste-dbx5x0.dtsi
@@ -878,7 +878,7 @@
 			power-domains = <&pm_domains DOMAIN_VAPE>;
 		};
 
-		ssp@80002000 {
+		spi@80002000 {
 			compatible = "arm,pl022", "arm,primecell";
 			reg = <0x80002000 0x1000>;
 			interrupts = <GIC_SPI 14 IRQ_TYPE_LEVEL_HIGH>;
@@ -892,7 +892,7 @@
 			power-domains = <&pm_domains DOMAIN_VAPE>;
 		};
 
-		ssp@80003000 {
+		spi@80003000 {
 			compatible = "arm,pl022", "arm,primecell";
 			reg = <0x80003000 0x1000>;
 			interrupts = <GIC_SPI 52 IRQ_TYPE_LEVEL_HIGH>;
diff --git a/arch/arm/boot/dts/ste-hrefprev60.dtsi b/arch/arm/boot/dts/ste-hrefprev60.dtsi
index 3f14b4df69b4e..94eeb7f1c9478 100644
--- a/arch/arm/boot/dts/ste-hrefprev60.dtsi
+++ b/arch/arm/boot/dts/ste-hrefprev60.dtsi
@@ -57,7 +57,7 @@
 			};
 		};
 
-		ssp@80002000 {
+		spi@80002000 {
 			/*
 			 * On the first generation boards, this SSP/SPI port was connected
 			 * to the AB8500.
diff --git a/arch/arm/boot/dts/ste-snowball.dts b/arch/arm/boot/dts/ste-snowball.dts
index ade1d0d4e5f45..1bf4358f8fa71 100644
--- a/arch/arm/boot/dts/ste-snowball.dts
+++ b/arch/arm/boot/dts/ste-snowball.dts
@@ -376,7 +376,7 @@
 			pinctrl-1 = <&i2c3_sleep_mode>;
 		};
 
-		ssp@80002000 {
+		spi@80002000 {
 			pinctrl-names = "default";
 			pinctrl-0 = <&ssp0_snowball_mode>;
 		};
diff --git a/arch/arm/boot/dts/ste-u300.dts b/arch/arm/boot/dts/ste-u300.dts
index 62ecb6a2fa39e..1bd1aba3322f1 100644
--- a/arch/arm/boot/dts/ste-u300.dts
+++ b/arch/arm/boot/dts/ste-u300.dts
@@ -442,7 +442,7 @@
 			dma-names = "rx";
 		};
 
-		spi: ssp@c0006000 {
+		spi: spi@c0006000 {
 			compatible = "arm,pl022", "arm,primecell";
 			reg = <0xc0006000 0x1000>;
 			interrupt-parent = <&vica>;
-- 
2.20.1

[PATCH AUTOSEL 4.14 038/109] ARM: dts: marvell: Fix SPI and I2C bus warnings

[Sasha Levin]

From: Rob Herring <robh@kernel.org>

[ Upstream commit cf680cc5251487b9a39919c3cda31a108af19cf8 ]

dtc has new checks for I2C and SPI buses. Fix the warnings in node names
and unit-addresses.

arch/arm/boot/dts/dove-cubox.dtb: Warning (i2c_bus_reg): /i2c-mux/i2c@0/clock-generator: I2C bus unit address format error, expected "60"
arch/arm/boot/dts/dove-cubox-es.dtb: Warning (i2c_bus_reg): /i2c-mux/i2c@0/clock-generator: I2C bus unit address format error, expected "60"
arch/arm/boot/dts/dove-cubox.dtb: Warning (spi_bus_bridge): /mbus/internal-regs/spi-ctrl@10600: node name for SPI buses should be 'spi'
arch/arm/boot/dts/dove-cubox-es.dtb: Warning (spi_bus_bridge): /mbus/internal-regs/spi-ctrl@10600: node name for SPI buses should be 'spi'
arch/arm/boot/dts/dove-dove-db.dtb: Warning (spi_bus_bridge): /mbus/internal-regs/spi-ctrl@10600: node name for SPI buses should be 'spi'
arch/arm/boot/dts/dove-sbc-a510.dtb: Warning (spi_bus_bridge): /mbus/internal-regs/spi-ctrl@10600: node name for SPI buses should be 'spi'
arch/arm/boot/dts/dove-sbc-a510.dtb: Warning (spi_bus_bridge): /mbus/internal-regs/spi-ctrl@14600: node name for SPI buses should be 'spi'
arch/arm/boot/dts/orion5x-kuroboxpro.dtb: Warning (i2c_bus_reg): /soc/internal-regs/i2c@11000/rtc: I2C bus unit address format error, expected "32"
arch/arm/boot/dts/orion5x-linkstation-lschl.dtb: Warning (i2c_bus_reg): /soc/internal-regs/i2c@11000/rtc: I2C bus unit address format error, expected "32"
arch/arm/boot/dts/orion5x-linkstation-lsgl.dtb: Warning (i2c_bus_reg): /soc/internal-regs/i2c@11000/rtc: I2C bus unit address format error, expected "32"
arch/arm/boot/dts/orion5x-linkstation-lswtgl.dtb: Warning (i2c_bus_reg): /soc/internal-regs/i2c@11000/rtc: I2C bus unit address format error, expected "32"

Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Andrew Lunn <andrew@lunn.ch>
Cc: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Cc: Gregory Clement <gregory.clement@bootlin.com>
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 arch/arm/boot/dts/dove-cubox.dts           | 2 +-
 arch/arm/boot/dts/dove.dtsi                | 6 +++---
 arch/arm/boot/dts/orion5x-linkstation.dtsi | 2 +-
 3 files changed, 5 insertions(+), 5 deletions(-)

diff --git a/arch/arm/boot/dts/dove-cubox.dts b/arch/arm/boot/dts/dove-cubox.dts
index 580e3cbcfbf7c..3e1584e787aec 100644
--- a/arch/arm/boot/dts/dove-cubox.dts
+++ b/arch/arm/boot/dts/dove-cubox.dts
@@ -87,7 +87,7 @@
 	status = "okay";
 	clock-frequency = <100000>;
 
-	si5351: clock-generator {
+	si5351: clock-generator@60 {
 		compatible = "silabs,si5351a-msop";
 		reg = <0x60>;
 		#address-cells = <1>;
diff --git a/arch/arm/boot/dts/dove.dtsi b/arch/arm/boot/dts/dove.dtsi
index f4a07bb7c3a29..c78471b05ab46 100644
--- a/arch/arm/boot/dts/dove.dtsi
+++ b/arch/arm/boot/dts/dove.dtsi
@@ -155,7 +155,7 @@
 				  0xffffe000 MBUS_ID(0x03, 0x01) 0 0x0000800   /* CESA SRAM  2k */
 				  0xfffff000 MBUS_ID(0x0d, 0x00) 0 0x0000800>; /* PMU  SRAM  2k */
 
-			spi0: spi-ctrl@10600 {
+			spi0: spi@10600 {
 				compatible = "marvell,orion-spi";
 				#address-cells = <1>;
 				#size-cells = <0>;
@@ -168,7 +168,7 @@
 				status = "disabled";
 			};
 
-			i2c: i2c-ctrl@11000 {
+			i2c: i2c@11000 {
 				compatible = "marvell,mv64xxx-i2c";
 				reg = <0x11000 0x20>;
 				#address-cells = <1>;
@@ -218,7 +218,7 @@
 				status = "disabled";
 			};
 
-			spi1: spi-ctrl@14600 {
+			spi1: spi@14600 {
 				compatible = "marvell,orion-spi";
 				#address-cells = <1>;
 				#size-cells = <0>;
diff --git a/arch/arm/boot/dts/orion5x-linkstation.dtsi b/arch/arm/boot/dts/orion5x-linkstation.dtsi
index e9991c83d7b70..117d71546ed0f 100644
--- a/arch/arm/boot/dts/orion5x-linkstation.dtsi
+++ b/arch/arm/boot/dts/orion5x-linkstation.dtsi
@@ -156,7 +156,7 @@
 &i2c {
 	status = "okay";
 
-	rtc {
+	rtc@32 {
 		compatible = "ricoh,rs5c372a";
 		reg = <0x32>;
 	};
-- 
2.20.1

[PATCH AUTOSEL 4.14 040/109] ARM: dts: clearfog: fix sdhci supply property name

[Sasha Levin]

From: Baruch Siach <baruch@tkos.co.il>

[ Upstream commit e807f0298144c06740022a2f900d86b7f115595e ]

The vmmc phandle, like all power supply property names, must have the
'-supply' suffix.

Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 arch/arm/boot/dts/armada-388-clearfog.dtsi | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)

diff --git a/arch/arm/boot/dts/armada-388-clearfog.dtsi b/arch/arm/boot/dts/armada-388-clearfog.dtsi
index 68acfc9687069..8a3bbb7d6cc10 100644
--- a/arch/arm/boot/dts/armada-388-clearfog.dtsi
+++ b/arch/arm/boot/dts/armada-388-clearfog.dtsi
@@ -89,7 +89,7 @@
 					     &clearfog_sdhci_cd_pins>;
 				pinctrl-names = "default";
 				status = "okay";
-				vmmc = <&reg_3p3v>;
+				vmmc-supply = <&reg_3p3v>;
 				wp-inverted;
 			};
 
-- 
2.20.1

[PATCH AUTOSEL 4.14 043/109] net: phy: mdio-bcm-unimac: Allow configuring MDIO clock divider

[Sasha Levin]

From: Florian Fainelli <f.fainelli@gmail.com>

[ Upstream commit b78ac6ecd1b6b46f8767cbafa95a7b0b51b87ad8 ]

Allow the configuration of the MDIO clock divider when the Device Tree
contains 'clock-frequency' property (similar to I2C and SPI buses).
Because the hardware may have lost its state during suspend/resume,
re-apply the MDIO clock divider upon resumption.

Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 .../bindings/net/brcm,unimac-mdio.txt         |  3 +
 drivers/net/phy/mdio-bcm-unimac.c             | 83 ++++++++++++++++++-
 2 files changed, 84 insertions(+), 2 deletions(-)

diff --git a/Documentation/devicetree/bindings/net/brcm,unimac-mdio.txt b/Documentation/devicetree/bindings/net/brcm,unimac-mdio.txt
index 4648948f7c3b8..e15589f477876 100644
--- a/Documentation/devicetree/bindings/net/brcm,unimac-mdio.txt
+++ b/Documentation/devicetree/bindings/net/brcm,unimac-mdio.txt
@@ -19,6 +19,9 @@ Optional properties:
 - interrupt-names: must be "mdio_done_error" when there is a share interrupt fed
   to this hardware block, or must be "mdio_done" for the first interrupt and
   "mdio_error" for the second when there are separate interrupts
+- clocks: A reference to the clock supplying the MDIO bus controller
+- clock-frequency: the MDIO bus clock that must be output by the MDIO bus
+  hardware, if absent, the default hardware values are used
 
 Child nodes of this MDIO bus controller node are standard Ethernet PHY device
 nodes as described in Documentation/devicetree/bindings/net/phy.txt
diff --git a/drivers/net/phy/mdio-bcm-unimac.c b/drivers/net/phy/mdio-bcm-unimac.c
index 08e0647b85e23..f9d98a6e67bc4 100644
--- a/drivers/net/phy/mdio-bcm-unimac.c
+++ b/drivers/net/phy/mdio-bcm-unimac.c
@@ -16,6 +16,7 @@
 #include <linux/module.h>
 #include <linux/io.h>
 #include <linux/delay.h>
+#include <linux/clk.h>
 
 #include <linux/of.h>
 #include <linux/of_platform.h>
@@ -45,6 +46,8 @@ struct unimac_mdio_priv {
 	void __iomem		*base;
 	int (*wait_func)	(void *wait_func_data);
 	void			*wait_func_data;
+	struct clk		*clk;
+	u32			clk_freq;
 };
 
 static inline u32 unimac_mdio_readl(struct unimac_mdio_priv *priv, u32 offset)
@@ -189,6 +192,35 @@ static int unimac_mdio_reset(struct mii_bus *bus)
 	return 0;
 }
 
+static void unimac_mdio_clk_set(struct unimac_mdio_priv *priv)
+{
+	unsigned long rate;
+	u32 reg, div;
+
+	/* Keep the hardware default values */
+	if (!priv->clk_freq)
+		return;
+
+	if (!priv->clk)
+		rate = 250000000;
+	else
+		rate = clk_get_rate(priv->clk);
+
+	div = (rate / (2 * priv->clk_freq)) - 1;
+	if (div & ~MDIO_CLK_DIV_MASK) {
+		pr_warn("Incorrect MDIO clock frequency, ignoring\n");
+		return;
+	}
+
+	/* The MDIO clock is the reference clock (typicaly 250Mhz) divided by
+	 * 2 x (MDIO_CLK_DIV + 1)
+	 */
+	reg = unimac_mdio_readl(priv, MDIO_CFG);
+	reg &= ~(MDIO_CLK_DIV_MASK << MDIO_CLK_DIV_SHIFT);
+	reg |= div << MDIO_CLK_DIV_SHIFT;
+	unimac_mdio_writel(priv, reg, MDIO_CFG);
+}
+
 static int unimac_mdio_probe(struct platform_device *pdev)
 {
 	struct unimac_mdio_pdata *pdata = pdev->dev.platform_data;
@@ -215,9 +247,26 @@ static int unimac_mdio_probe(struct platform_device *pdev)
 		return -ENOMEM;
 	}
 
+	priv->clk = devm_clk_get(&pdev->dev, NULL);
+	if (PTR_ERR(priv->clk) == -EPROBE_DEFER)
+		return PTR_ERR(priv->clk);
+	else
+		priv->clk = NULL;
+
+	ret = clk_prepare_enable(priv->clk);
+	if (ret)
+		return ret;
+
+	if (of_property_read_u32(np, "clock-frequency", &priv->clk_freq))
+		priv->clk_freq = 0;
+
+	unimac_mdio_clk_set(priv);
+
 	priv->mii_bus = mdiobus_alloc();
-	if (!priv->mii_bus)
-		return -ENOMEM;
+	if (!priv->mii_bus) {
+		ret = -ENOMEM;
+		goto out_clk_disable;
+	}
 
 	bus = priv->mii_bus;
 	bus->priv = priv;
@@ -251,6 +300,8 @@ static int unimac_mdio_probe(struct platform_device *pdev)
 
 out_mdio_free:
 	mdiobus_free(bus);
+out_clk_disable:
+	clk_disable_unprepare(priv->clk);
 	return ret;
 }
 
@@ -260,10 +311,37 @@ static int unimac_mdio_remove(struct platform_device *pdev)
 
 	mdiobus_unregister(priv->mii_bus);
 	mdiobus_free(priv->mii_bus);
+	clk_disable_unprepare(priv->clk);
+
+	return 0;
+}
+
+static int unimac_mdio_suspend(struct device *d)
+{
+	struct unimac_mdio_priv *priv = dev_get_drvdata(d);
+
+	clk_disable_unprepare(priv->clk);
+
+	return 0;
+}
+
+static int unimac_mdio_resume(struct device *d)
+{
+	struct unimac_mdio_priv *priv = dev_get_drvdata(d);
+	int ret;
+
+	ret = clk_prepare_enable(priv->clk);
+	if (ret)
+		return ret;
+
+	unimac_mdio_clk_set(priv);
 
 	return 0;
 }
 
+static SIMPLE_DEV_PM_OPS(unimac_mdio_pm_ops,
+			 unimac_mdio_suspend, unimac_mdio_resume);
+
 static const struct of_device_id unimac_mdio_ids[] = {
 	{ .compatible = "brcm,genet-mdio-v5", },
 	{ .compatible = "brcm,genet-mdio-v4", },
@@ -279,6 +357,7 @@ static struct platform_driver unimac_mdio_driver = {
 	.driver = {
 		.name = UNIMAC_MDIO_DRV_NAME,
 		.of_match_table = unimac_mdio_ids,
+		.pm = &unimac_mdio_pm_ops,
 	},
 	.probe	= unimac_mdio_probe,
 	.remove	= unimac_mdio_remove,
-- 
2.20.1

[PATCH AUTOSEL 4.14 049/109] arm64: dts: rockchip: Fix microSD in rk3399 sapphire board

[Sasha Levin]

From: Vicente Bergas <vicencb@gmail.com>

[ Upstream commit 88a20edf76091ee7f1bb459b89d714d53f0f8940 ]

The microSD card slot in the Sapphire board is not working because of
several issues:
 1.- The vmmc power supply is missing in the DTS. It is capable of 3.0V
 and has a GPIO-based enable control.
 2.- The vqmmc power supply can provide up to 3.3V, but it is capped in
 the DTS to just 3.0V because of the vmmc capability. This results in a
 conflict from the mmc driver requesting an unsupportable voltage range
 from 3.3V to 3.0V (min > max) as reported in dmesg. So, extend the
 range up to 3.3V. The hw should be able to stand this 0.3V tolerance.
 See mmc_regulator_set_vqmmc in drivers/mmc/core/core.c.
 3.- The card detect signal is non-working. There is a known conflict
 with jtag, but the workaround in drivers/soc/rockchip/grf.c does not
 work. Adding the broken-cd attribute to the DTS fixes the issue.

Signed-off-by: Vicente Bergas <vicencb@gmail.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 .../boot/dts/rockchip/rk3399-sapphire.dtsi    | 24 ++++++++++++++++++-
 1 file changed, 23 insertions(+), 1 deletion(-)

diff --git a/arch/arm64/boot/dts/rockchip/rk3399-sapphire.dtsi b/arch/arm64/boot/dts/rockchip/rk3399-sapphire.dtsi
index ce592a4c0c4cd..6e40133372a80 100644
--- a/arch/arm64/boot/dts/rockchip/rk3399-sapphire.dtsi
+++ b/arch/arm64/boot/dts/rockchip/rk3399-sapphire.dtsi
@@ -113,6 +113,19 @@
 		vin-supply = <&vcc_1v8>;
 	};
 
+	vcc3v0_sd: vcc3v0-sd {
+		compatible = "regulator-fixed";
+		enable-active-high;
+		gpio = <&gpio0 RK_PA1 GPIO_ACTIVE_HIGH>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&sdmmc0_pwr_h>;
+		regulator-always-on;
+		regulator-max-microvolt = <3000000>;
+		regulator-min-microvolt = <3000000>;
+		regulator-name = "vcc3v0_sd";
+		vin-supply = <&vcc3v3_sys>;
+	};
+
 	vcc3v3_sys: vcc3v3-sys {
 		compatible = "regulator-fixed";
 		regulator-name = "vcc3v3_sys";
@@ -315,7 +328,7 @@
 				regulator-always-on;
 				regulator-boot-on;
 				regulator-min-microvolt = <1800000>;
-				regulator-max-microvolt = <3000000>;
+				regulator-max-microvolt = <3300000>;
 				regulator-state-mem {
 					regulator-on-in-suspend;
 					regulator-suspend-microvolt = <3000000>;
@@ -490,6 +503,13 @@
 		};
 	};
 
+	sd {
+		sdmmc0_pwr_h: sdmmc0-pwr-h {
+			rockchip,pins =
+				<RK_GPIO0 RK_PA1 RK_FUNC_GPIO &pcfg_pull_none>;
+		};
+	};
+
 	usb2 {
 		vcc5v0_host_en: vcc5v0-host-en {
 			rockchip,pins =
@@ -537,6 +557,7 @@
 };
 
 &sdmmc {
+	broken-cd;
 	bus-width = <4>;
 	cap-mmc-highspeed;
 	cap-sd-highspeed;
@@ -545,6 +566,7 @@
 	max-frequency = <150000000>;
 	pinctrl-names = "default";
 	pinctrl-0 = <&sdmmc_clk &sdmmc_cmd &sdmmc_cd &sdmmc_bus4>;
+	vmmc-supply = <&vcc3v0_sd>;
 	vqmmc-supply = <&vcc_sdio>;
 	status = "okay";
 };
-- 
2.20.1

[PATCH AUTOSEL 4.14 053/109] ARM: dts: rockchip: explicitly set vcc_sd0 pin to gpio on rk3188-radxarock

[Sasha Levin]

From: Heiko Stuebner <heiko@sntech.de>

[ Upstream commit a2df0984e73fd9e1dad5fc3f1c307ec3de395e30 ]

It is good practice to make the setting of gpio-pinctrls explicitly in the
devicetree, and in this case even necessary.
Rockchip boards start with iomux settings set to gpio for most pins and
while the linux pinctrl driver also implicitly sets the gpio function if
a pin is requested as gpio that is not necessarily true for other drivers.

The issue in question stems from uboot, where the sdmmc_pwr pin is set
to function 1 (sdmmc-power) by the bootrom when reading the 1st-stage
loader. The regulator controlled by the pin is active-low though, so
when the dwmmc hw-block sets its enabled bit, it actually disables the
regulator. By changing the pin back to gpio we fix that behaviour.

Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 arch/arm/boot/dts/rk3188-radxarock.dts | 8 ++++++++
 1 file changed, 8 insertions(+)

diff --git a/arch/arm/boot/dts/rk3188-radxarock.dts b/arch/arm/boot/dts/rk3188-radxarock.dts
index 53d6fc2fdbce8..541a798d3d202 100644
--- a/arch/arm/boot/dts/rk3188-radxarock.dts
+++ b/arch/arm/boot/dts/rk3188-radxarock.dts
@@ -130,6 +130,8 @@
 		regulator-min-microvolt = <3300000>;
 		regulator-max-microvolt = <3300000>;
 		gpio = <&gpio3 RK_PA1 GPIO_ACTIVE_LOW>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&sdmmc_pwr>;
 		startup-delay-us = <100000>;
 		vin-supply = <&vcc_io>;
 	};
@@ -348,6 +350,12 @@
 		};
 	};
 
+	sd0 {
+		sdmmc_pwr: sdmmc-pwr {
+			rockchip,pins = <RK_GPIO3 1 RK_FUNC_GPIO &pcfg_pull_none>;
+		};
+	};
+
 	usb {
 		host_vbus_drv: host-vbus-drv {
 			rockchip,pins = <0 3 RK_FUNC_GPIO &pcfg_pull_none>;
-- 
2.20.1

[PATCH AUTOSEL 4.14 073/109] ARM: dts: tegra30: fix xcvr-setup-use-fuses

[Sasha Levin]

From: Marcel Ziswiler <marcel.ziswiler@toradex.com>

[ Upstream commit 564706f65cda3de52b09e51feb423a43940fe661 ]

There was a dot instead of a comma. Fix this.

Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 arch/arm/boot/dts/tegra30.dtsi | 6 +++---
 1 file changed, 3 insertions(+), 3 deletions(-)

diff --git a/arch/arm/boot/dts/tegra30.dtsi b/arch/arm/boot/dts/tegra30.dtsi
index c3e9f1e847db8..cb5b76e958131 100644
--- a/arch/arm/boot/dts/tegra30.dtsi
+++ b/arch/arm/boot/dts/tegra30.dtsi
@@ -840,7 +840,7 @@
 		nvidia,elastic-limit = <16>;
 		nvidia,term-range-adj = <6>;
 		nvidia,xcvr-setup = <51>;
-		nvidia.xcvr-setup-use-fuses;
+		nvidia,xcvr-setup-use-fuses;
 		nvidia,xcvr-lsfslew = <1>;
 		nvidia,xcvr-lsrslew = <1>;
 		nvidia,xcvr-hsslew = <32>;
@@ -877,7 +877,7 @@
 		nvidia,elastic-limit = <16>;
 		nvidia,term-range-adj = <6>;
 		nvidia,xcvr-setup = <51>;
-		nvidia.xcvr-setup-use-fuses;
+		nvidia,xcvr-setup-use-fuses;
 		nvidia,xcvr-lsfslew = <2>;
 		nvidia,xcvr-lsrslew = <2>;
 		nvidia,xcvr-hsslew = <32>;
@@ -913,7 +913,7 @@
 		nvidia,elastic-limit = <16>;
 		nvidia,term-range-adj = <6>;
 		nvidia,xcvr-setup = <51>;
-		nvidia.xcvr-setup-use-fuses;
+		nvidia,xcvr-setup-use-fuses;
 		nvidia,xcvr-lsfslew = <2>;
 		nvidia,xcvr-lsrslew = <2>;
 		nvidia,xcvr-hsslew = <32>;
-- 
2.20.1

[PATCH AUTOSEL 4.14 074/109] ARM: tegra: apalis_t30: fix mmc1 cmd pull-up

[Sasha Levin]

From: Marcel Ziswiler <marcel.ziswiler@toradex.com>

[ Upstream commit 1c997fe4becdc6fcbc06e23982ceb65621e6572a ]

Fix MMC1 cmd pin pull-up causing issues on carrier boards without
external pull-up.

Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 arch/arm/boot/dts/tegra30-apalis.dtsi | 6 +++---
 1 file changed, 3 insertions(+), 3 deletions(-)

diff --git a/arch/arm/boot/dts/tegra30-apalis.dtsi b/arch/arm/boot/dts/tegra30-apalis.dtsi
index faa8cd2914e8b..b9368d40bc6fb 100644
--- a/arch/arm/boot/dts/tegra30-apalis.dtsi
+++ b/arch/arm/boot/dts/tegra30-apalis.dtsi
@@ -166,14 +166,14 @@
 
 			/* Apalis MMC1 */
 			sdmmc3_clk_pa6 {
-				nvidia,pins = "sdmmc3_clk_pa6",
-					      "sdmmc3_cmd_pa7";
+				nvidia,pins = "sdmmc3_clk_pa6";
 				nvidia,function = "sdmmc3";
 				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
 				nvidia,tristate = <TEGRA_PIN_DISABLE>;
 			};
 			sdmmc3_dat0_pb7 {
-				nvidia,pins = "sdmmc3_dat0_pb7",
+				nvidia,pins = "sdmmc3_cmd_pa7",
+					      "sdmmc3_dat0_pb7",
 					      "sdmmc3_dat1_pb6",
 					      "sdmmc3_dat2_pb5",
 					      "sdmmc3_dat3_pb4",
-- 
2.20.1

[PATCH AUTOSEL 4.14 075/109] ARM: dts: paz00: fix wakeup gpio keycode

[Sasha Levin]

From: Marc Dietrich <marvin24@gmx.de>

[ Upstream commit ebea2a43fdafdbce918bd7e200b709d6c33b9f3b ]

The power key is controlled solely by the EC, which only tiggeres this
gpio after wakeup.
Fixes immediately return to suspend after wake from LP1.

Signed-off-by: Marc Dietrich <marvin24@gmx.de>
Tested-by: Nicolas Chauvet <kwizart@gmail.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 arch/arm/boot/dts/tegra20-paz00.dts | 6 +++---
 1 file changed, 3 insertions(+), 3 deletions(-)

diff --git a/arch/arm/boot/dts/tegra20-paz00.dts b/arch/arm/boot/dts/tegra20-paz00.dts
index 30436969adc0e..1b8db91277b1c 100644
--- a/arch/arm/boot/dts/tegra20-paz00.dts
+++ b/arch/arm/boot/dts/tegra20-paz00.dts
@@ -524,10 +524,10 @@
 	gpio-keys {
 		compatible = "gpio-keys";
 
-		power {
-			label = "Power";
+		wakeup {
+			label = "Wakeup";
 			gpios = <&gpio TEGRA_GPIO(J, 7) GPIO_ACTIVE_LOW>;
-			linux,code = <KEY_POWER>;
+			linux,code = <KEY_WAKEUP>;
 			wakeup-source;
 		};
 	};
-- 
2.20.1

[PATCH AUTOSEL 4.14 081/109] ARM: dts: realview: Fix SPI controller node names

[Sasha Levin]

From: Rob Herring <robh@kernel.org>

[ Upstream commit 016add12977bcc30f77d7e48fc9a3a024cb46645 ]

SPI controller nodes should be named 'spi' rather than 'ssp'. Fixing the
name enables dtc SPI bus checks.

Cc: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 arch/arm/boot/dts/arm-realview-eb.dtsi    | 2 +-
 arch/arm/boot/dts/arm-realview-pb1176.dts | 2 +-
 arch/arm/boot/dts/arm-realview-pb11mp.dts | 2 +-
 arch/arm/boot/dts/arm-realview-pbx.dtsi   | 2 +-
 arch/arm/boot/dts/versatile-ab.dts        | 2 +-
 5 files changed, 5 insertions(+), 5 deletions(-)

diff --git a/arch/arm/boot/dts/arm-realview-eb.dtsi b/arch/arm/boot/dts/arm-realview-eb.dtsi
index e2e9599596e25..05379b6c1c13b 100644
--- a/arch/arm/boot/dts/arm-realview-eb.dtsi
+++ b/arch/arm/boot/dts/arm-realview-eb.dtsi
@@ -334,7 +334,7 @@
 			clock-names = "uartclk", "apb_pclk";
 		};
 
-		ssp: ssp@1000d000 {
+		ssp: spi@1000d000 {
 			compatible = "arm,pl022", "arm,primecell";
 			reg = <0x1000d000 0x1000>;
 			clocks = <&sspclk>, <&pclk>;
diff --git a/arch/arm/boot/dts/arm-realview-pb1176.dts b/arch/arm/boot/dts/arm-realview-pb1176.dts
index c789564f28033..c1fd5615ddfe3 100644
--- a/arch/arm/boot/dts/arm-realview-pb1176.dts
+++ b/arch/arm/boot/dts/arm-realview-pb1176.dts
@@ -343,7 +343,7 @@
 			clock-names = "apb_pclk";
 		};
 
-		pb1176_ssp: ssp@1010b000 {
+		pb1176_ssp: spi@1010b000 {
 			compatible = "arm,pl022", "arm,primecell";
 			reg = <0x1010b000 0x1000>;
 			interrupt-parent = <&intc_dc1176>;
diff --git a/arch/arm/boot/dts/arm-realview-pb11mp.dts b/arch/arm/boot/dts/arm-realview-pb11mp.dts
index 3944765ac4b06..e306f1cceb4ec 100644
--- a/arch/arm/boot/dts/arm-realview-pb11mp.dts
+++ b/arch/arm/boot/dts/arm-realview-pb11mp.dts
@@ -480,7 +480,7 @@
 			clock-names = "uartclk", "apb_pclk";
 		};
 
-		ssp@1000d000 {
+		spi@1000d000 {
 			compatible = "arm,pl022", "arm,primecell";
 			reg = <0x1000d000 0x1000>;
 			interrupt-parent = <&intc_pb11mp>;
diff --git a/arch/arm/boot/dts/arm-realview-pbx.dtsi b/arch/arm/boot/dts/arm-realview-pbx.dtsi
index aeb49c4bd773f..2bf3958b2e6b9 100644
--- a/arch/arm/boot/dts/arm-realview-pbx.dtsi
+++ b/arch/arm/boot/dts/arm-realview-pbx.dtsi
@@ -318,7 +318,7 @@
 			clock-names = "uartclk", "apb_pclk";
 		};
 
-		ssp: ssp@1000d000 {
+		ssp: spi@1000d000 {
 			compatible = "arm,pl022", "arm,primecell";
 			reg = <0x1000d000 0x1000>;
 			clocks = <&sspclk>, <&pclk>;
diff --git a/arch/arm/boot/dts/versatile-ab.dts b/arch/arm/boot/dts/versatile-ab.dts
index 4a51612996bc2..a9000d22b2c00 100644
--- a/arch/arm/boot/dts/versatile-ab.dts
+++ b/arch/arm/boot/dts/versatile-ab.dts
@@ -304,7 +304,7 @@
 			clock-names = "apb_pclk";
 		};
 
-		ssp@101f4000 {
+		spi@101f4000 {
 			compatible = "arm,pl022", "arm,primecell";
 			reg = <0x101f4000 0x1000>;
 			interrupts = <11>;
-- 
2.20.1

[PATCH AUTOSEL 4.14 100/109] arm64: dts: amd: Fix SPI bus warnings

[Sasha Levin]

From: Rob Herring <robh@kernel.org>

[ Upstream commit e9f0878c4b2004ac19581274c1ae4c61ae3ca70e ]

dtc has new checks for SPI buses. Fix the warnings in node names.

arch/arm64/boot/dts/amd/amd-overdrive.dtb: Warning (spi_bus_bridge): /smb/ssp@e1030000: node name for SPI buses should be 'spi'
arch/arm64/boot/dts/amd/amd-overdrive-rev-b0.dtb: Warning (spi_bus_bridge): /smb/ssp@e1030000: node name for SPI buses should be 'spi'
arch/arm64/boot/dts/amd/amd-overdrive-rev-b1.dtb: Warning (spi_bus_bridge): /smb/ssp@e1030000: node name for SPI buses should be 'spi'

Cc: Brijesh Singh <brijeshkumar.singh@amd.com>
Cc: Suravee Suthikulpanit <suravee.suthikulpanit@amd.com>
Cc: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 arch/arm64/boot/dts/amd/amd-seattle-soc.dtsi | 4 ++--
 1 file changed, 2 insertions(+), 2 deletions(-)

diff --git a/arch/arm64/boot/dts/amd/amd-seattle-soc.dtsi b/arch/arm64/boot/dts/amd/amd-seattle-soc.dtsi
index 125f4deb52fe9..b664e7af74eb3 100644
--- a/arch/arm64/boot/dts/amd/amd-seattle-soc.dtsi
+++ b/arch/arm64/boot/dts/amd/amd-seattle-soc.dtsi
@@ -107,7 +107,7 @@
 			clock-names = "uartclk", "apb_pclk";
 		};
 
-		spi0: ssp@e1020000 {
+		spi0: spi@e1020000 {
 			status = "disabled";
 			compatible = "arm,pl022", "arm,primecell";
 			reg = <0 0xe1020000 0 0x1000>;
@@ -117,7 +117,7 @@
 			clock-names = "apb_pclk";
 		};
 
-		spi1: ssp@e1030000 {
+		spi1: spi@e1030000 {
 			status = "disabled";
 			compatible = "arm,pl022", "arm,primecell";
 			reg = <0 0xe1030000 0 0x1000>;
-- 
2.20.1

[PATCH AUTOSEL 4.14 101/109] arm64: dts: lg: Fix SPI controller node names

[Sasha Levin]

From: Rob Herring <robh@kernel.org>

[ Upstream commit 09bae3b64cb580c95329bd8d16f08f0a5cb81ec9 ]

SPI controller nodes should be named 'spi' rather than 'ssp'. Fixing the
name enables dtc SPI bus checks.

Cc: Chanho Min <chanho.min@lge.com>
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 arch/arm64/boot/dts/lg/lg1312.dtsi | 4 ++--
 arch/arm64/boot/dts/lg/lg1313.dtsi | 4 ++--
 2 files changed, 4 insertions(+), 4 deletions(-)

diff --git a/arch/arm64/boot/dts/lg/lg1312.dtsi b/arch/arm64/boot/dts/lg/lg1312.dtsi
index 860c8fb107950..4bde7b6f2b113 100644
--- a/arch/arm64/boot/dts/lg/lg1312.dtsi
+++ b/arch/arm64/boot/dts/lg/lg1312.dtsi
@@ -168,14 +168,14 @@
 			clock-names = "apb_pclk";
 			status="disabled";
 		};
-		spi0: ssp@fe800000 {
+		spi0: spi@fe800000 {
 			compatible = "arm,pl022", "arm,primecell";
 			reg = <0x0 0xfe800000 0x1000>;
 			interrupts = <GIC_SPI 3 IRQ_TYPE_LEVEL_HIGH>;
 			clocks = <&clk_bus>;
 			clock-names = "apb_pclk";
 		};
-		spi1: ssp@fe900000 {
+		spi1: spi@fe900000 {
 			compatible = "arm,pl022", "arm,primecell";
 			reg = <0x0 0xfe900000 0x1000>;
 			interrupts = <GIC_SPI 4 IRQ_TYPE_LEVEL_HIGH>;
diff --git a/arch/arm64/boot/dts/lg/lg1313.dtsi b/arch/arm64/boot/dts/lg/lg1313.dtsi
index 1887af654a7db..16ced1ff1ad36 100644
--- a/arch/arm64/boot/dts/lg/lg1313.dtsi
+++ b/arch/arm64/boot/dts/lg/lg1313.dtsi
@@ -168,14 +168,14 @@
 			clock-names = "apb_pclk";
 			status="disabled";
 		};
-		spi0: ssp@fe800000 {
+		spi0: spi@fe800000 {
 			compatible = "arm,pl022", "arm,primecell";
 			reg = <0x0 0xfe800000 0x1000>;
 			interrupts = <GIC_SPI 3 IRQ_TYPE_LEVEL_HIGH>;
 			clocks = <&clk_bus>;
 			clock-names = "apb_pclk";
 		};
-		spi1: ssp@fe900000 {
+		spi1: spi@fe900000 {
 			compatible = "arm,pl022", "arm,primecell";
 			reg = <0x0 0xfe900000 0x1000>;
 			interrupts = <GIC_SPI 4 IRQ_TYPE_LEVEL_HIGH>;
-- 
2.20.1

[PATCH AUTOSEL 4.14 102/109] ARM: dts: lpc32xx: Fix SPI controller node names

[Sasha Levin]

From: Rob Herring <robh@kernel.org>

[ Upstream commit 11236ef582b8d66290bb3b3710e03ca1d85d8ad8 ]

SPI controller nodes should be named 'spi' rather than 'ssp'. Fixing the
name enables dtc SPI bus checks.

Cc: Vladimir Zapolskiy <vz@mleia.com>
Cc: Sylvain Lemieux <slemieux.tyco@gmail.com>
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 arch/arm/boot/dts/lpc32xx.dtsi | 4 ++--
 1 file changed, 2 insertions(+), 2 deletions(-)

diff --git a/arch/arm/boot/dts/lpc32xx.dtsi b/arch/arm/boot/dts/lpc32xx.dtsi
index f22a33a018199..d077bd2b9583e 100644
--- a/arch/arm/boot/dts/lpc32xx.dtsi
+++ b/arch/arm/boot/dts/lpc32xx.dtsi
@@ -179,7 +179,7 @@
 			 * ssp0 and spi1 are shared pins;
 			 * enable one in your board dts, as needed.
 			 */
-			ssp0: ssp@20084000 {
+			ssp0: spi@20084000 {
 				compatible = "arm,pl022", "arm,primecell";
 				reg = <0x20084000 0x1000>;
 				interrupts = <20 IRQ_TYPE_LEVEL_HIGH>;
@@ -199,7 +199,7 @@
 			 * ssp1 and spi2 are shared pins;
 			 * enable one in your board dts, as needed.
 			 */
-			ssp1: ssp@2008c000 {
+			ssp1: spi@2008c000 {
 				compatible = "arm,pl022", "arm,primecell";
 				reg = <0x2008c000 0x1000>;
 				interrupts = <21 IRQ_TYPE_LEVEL_HIGH>;
-- 
2.20.1

[PATCH AUTOSEL 4.14 103/109] arm64: dts: rockchip: enable display nodes on rk3328-rock64

[Sasha Levin]

From: Heiko Stuebner <heiko@sntech.de>

[ Upstream commit e78d53c7b2873e0724eb765a88ccde42560b0e05 ]

Enable necessary nodes to get output on the hdmi port of the board.

Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 arch/arm64/boot/dts/rockchip/rk3328-rock64.dts | 16 ++++++++++++++++
 1 file changed, 16 insertions(+)

diff --git a/arch/arm64/boot/dts/rockchip/rk3328-rock64.dts b/arch/arm64/boot/dts/rockchip/rk3328-rock64.dts
index 3f8f528099a80..19c086f1bf6db 100644
--- a/arch/arm64/boot/dts/rockchip/rk3328-rock64.dts
+++ b/arch/arm64/boot/dts/rockchip/rk3328-rock64.dts
@@ -146,6 +146,14 @@
 	status = "okay";
 };
 
+&hdmi {
+	status = "okay";
+};
+
+&hdmiphy {
+	status = "okay";
+};
+
 &i2c1 {
 	status = "okay";
 
@@ -333,3 +341,11 @@
 &usb_host0_ohci {
 	status = "okay";
 };
+
+&vop {
+	status = "okay";
+};
+
+&vop_mmu {
+	status = "okay";
+};
-- 
2.20.1