* [PATCH v5 1/2] staging: iio: accel: adis16240: enforce SPI mode on probe function @ 2019-11-23 23:35 Rodrigo Carvalho 2019-11-23 23:35 ` [PATCH v5 2/2] dt-bindings: iio: accel: add binding documentation for ADIS16240 Rodrigo Carvalho 2019-11-25 7:55 ` [PATCH v5 1/2] staging: iio: accel: adis16240: enforce SPI mode on probe function Ardelean, Alexandru 0 siblings, 2 replies; 7+ messages in thread From: Rodrigo Carvalho @ 2019-11-23 23:35 UTC (permalink / raw) To: Lars-Peter Clausen, Michael Hennerich, Stefan Popa, Jonathan Cameron, Hartmut Knaack, Peter Meerwald-Stadler, Greg Kroah-Hartman, alexandru.ardelean Cc: linux-iio, devel, linux-kernel, devicetree, kernel-usp, Rodrigo Carvalho According to the datasheet, this driver supports only SPI mode 3, so we should enforce it and call spi_setup() on probe function. Signed-off-by: Rodrigo Ribeiro Carvalho <rodrigorsdc@gmail.com> --- V5: - Add this patch to the patchset drivers/staging/iio/accel/adis16240.c | 7 +++++++ 1 file changed, 7 insertions(+) diff --git a/drivers/staging/iio/accel/adis16240.c b/drivers/staging/iio/accel/adis16240.c index 82099db4bf0c..77b6b81767b9 100644 --- a/drivers/staging/iio/accel/adis16240.c +++ b/drivers/staging/iio/accel/adis16240.c @@ -400,6 +400,13 @@ static int adis16240_probe(struct spi_device *spi) indio_dev->num_channels = ARRAY_SIZE(adis16240_channels); indio_dev->modes = INDIO_DIRECT_MODE; + spi->mode = SPI_MODE_3; + ret = spi_setup(spi); + if (ret) { + dev_err(&spi->dev, "spi_setup failed!\n"); + return ret; + } + ret = adis_init(st, indio_dev, spi, &adis16240_data); if (ret) return ret; -- 2.24.0 ^ permalink raw reply related [flat|nested] 7+ messages in thread
* [PATCH v5 2/2] dt-bindings: iio: accel: add binding documentation for ADIS16240 2019-11-23 23:35 [PATCH v5 1/2] staging: iio: accel: adis16240: enforce SPI mode on probe function Rodrigo Carvalho @ 2019-11-23 23:35 ` Rodrigo Carvalho 2019-12-05 15:21 ` Rob Herring 2019-11-25 7:55 ` [PATCH v5 1/2] staging: iio: accel: adis16240: enforce SPI mode on probe function Ardelean, Alexandru 1 sibling, 1 reply; 7+ messages in thread From: Rodrigo Carvalho @ 2019-11-23 23:35 UTC (permalink / raw) To: Lars-Peter Clausen, Michael Hennerich, Stefan Popa, Jonathan Cameron, Hartmut Knaack, Peter Meerwald-Stadler, Greg Kroah-Hartman, alexandru.ardelean Cc: linux-iio, devel, linux-kernel, devicetree, kernel-usp, Rodrigo Carvalho This patch add device tree binding documentation for ADIS16240. Signed-off-by: Rodrigo Ribeiro Carvalho <rodrigorsdc@gmail.com> --- V5: - None .../bindings/iio/accel/adi,adis16240.yaml | 49 +++++++++++++++++++ 1 file changed, 49 insertions(+) create mode 100644 Documentation/devicetree/bindings/iio/accel/adi,adis16240.yaml diff --git a/Documentation/devicetree/bindings/iio/accel/adi,adis16240.yaml b/Documentation/devicetree/bindings/iio/accel/adi,adis16240.yaml new file mode 100644 index 000000000000..8e902f7c49e6 --- /dev/null +++ b/Documentation/devicetree/bindings/iio/accel/adi,adis16240.yaml @@ -0,0 +1,49 @@ +# SPDX-License-Identifier: GPL-2.0 +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/iio/accel/adi,adis16240.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: ADIS16240 Programmable Impact Sensor and Recorder driver + +maintainers: + - Alexandru Ardelean <alexandru.ardelean@analog.com> + +description: | + ADIS16240 Programmable Impact Sensor and Recorder driver that supports + SPI interface. + https://www.analog.com/en/products/adis16240.html + +properties: + compatible: + enum: + - adi,adis16240 + + reg: + maxItems: 1 + + interrupts: + maxItems: 1 + +required: + - compatible + - reg + - interrupts + +examples: + - | + #include <dt-bindings/gpio/gpio.h> + #include <dt-bindings/interrupt-controller/irq.h> + spi0 { + #address-cells = <1>; + #size-cells = <0>; + + /* Example for a SPI device node */ + accelerometer@0 { + compatible = "adi,adis16240"; + reg = <0>; + spi-max-frequency = <2500000>; + interrupt-parent = <&gpio0>; + interrupts = <0 IRQ_TYPE_LEVEL_HIGH>; + }; + }; -- 2.24.0 ^ permalink raw reply related [flat|nested] 7+ messages in thread
* Re: [PATCH v5 2/2] dt-bindings: iio: accel: add binding documentation for ADIS16240 2019-11-23 23:35 ` [PATCH v5 2/2] dt-bindings: iio: accel: add binding documentation for ADIS16240 Rodrigo Carvalho @ 2019-12-05 15:21 ` Rob Herring 2019-12-06 17:10 ` Jonathan Cameron 0 siblings, 1 reply; 7+ messages in thread From: Rob Herring @ 2019-12-05 15:21 UTC (permalink / raw) To: Rodrigo Carvalho Cc: Lars-Peter Clausen, Michael Hennerich, Stefan Popa, Jonathan Cameron, Hartmut Knaack, Peter Meerwald-Stadler, Greg Kroah-Hartman, alexandru.ardelean, linux-iio, devel, linux-kernel, devicetree, kernel-usp On Sat, Nov 23, 2019 at 08:35:10PM -0300, Rodrigo Carvalho wrote: > This patch add device tree binding documentation for ADIS16240. > > Signed-off-by: Rodrigo Ribeiro Carvalho <rodrigorsdc@gmail.com> checkpatch.pl complains about a mismatch between the author and S-o-b. > --- > V5: > - None > > .../bindings/iio/accel/adi,adis16240.yaml | 49 +++++++++++++++++++ > 1 file changed, 49 insertions(+) > create mode 100644 Documentation/devicetree/bindings/iio/accel/adi,adis16240.yaml > > diff --git a/Documentation/devicetree/bindings/iio/accel/adi,adis16240.yaml b/Documentation/devicetree/bindings/iio/accel/adi,adis16240.yaml > new file mode 100644 > index 000000000000..8e902f7c49e6 > --- /dev/null > +++ b/Documentation/devicetree/bindings/iio/accel/adi,adis16240.yaml > @@ -0,0 +1,49 @@ > +# SPDX-License-Identifier: GPL-2.0 Dual license new bindings please: (GPL-2.0-only OR BSD-2-Clause) With that, Reviewed-by: Rob Herring <robh@kernel.org> > +%YAML 1.2 > +--- > +$id: http://devicetree.org/schemas/iio/accel/adi,adis16240.yaml# > +$schema: http://devicetree.org/meta-schemas/core.yaml# > + > +title: ADIS16240 Programmable Impact Sensor and Recorder driver > + > +maintainers: > + - Alexandru Ardelean <alexandru.ardelean@analog.com> > + > +description: | > + ADIS16240 Programmable Impact Sensor and Recorder driver that supports > + SPI interface. > + https://www.analog.com/en/products/adis16240.html > + > +properties: > + compatible: > + enum: > + - adi,adis16240 > + > + reg: > + maxItems: 1 > + > + interrupts: > + maxItems: 1 > + > +required: > + - compatible > + - reg > + - interrupts > + > +examples: > + - | > + #include <dt-bindings/gpio/gpio.h> > + #include <dt-bindings/interrupt-controller/irq.h> > + spi0 { > + #address-cells = <1>; > + #size-cells = <0>; > + > + /* Example for a SPI device node */ > + accelerometer@0 { > + compatible = "adi,adis16240"; > + reg = <0>; > + spi-max-frequency = <2500000>; > + interrupt-parent = <&gpio0>; > + interrupts = <0 IRQ_TYPE_LEVEL_HIGH>; > + }; > + }; > -- > 2.24.0 > ^ permalink raw reply [flat|nested] 7+ messages in thread
* Re: [PATCH v5 2/2] dt-bindings: iio: accel: add binding documentation for ADIS16240 2019-12-05 15:21 ` Rob Herring @ 2019-12-06 17:10 ` Jonathan Cameron 0 siblings, 0 replies; 7+ messages in thread From: Jonathan Cameron @ 2019-12-06 17:10 UTC (permalink / raw) To: Rob Herring Cc: Rodrigo Carvalho, Lars-Peter Clausen, Michael Hennerich, Stefan Popa, Hartmut Knaack, Peter Meerwald-Stadler, Greg Kroah-Hartman, alexandru.ardelean, linux-iio, devel, linux-kernel, devicetree, kernel-usp On Thu, 5 Dec 2019 09:21:29 -0600 Rob Herring <robh@kernel.org> wrote: > On Sat, Nov 23, 2019 at 08:35:10PM -0300, Rodrigo Carvalho wrote: > > This patch add device tree binding documentation for ADIS16240. > > > > Signed-off-by: Rodrigo Ribeiro Carvalho <rodrigorsdc@gmail.com> > > checkpatch.pl complains about a mismatch between the author and S-o-b. The open question on patch 1 is resolved, so respin with the points Rob pointed out her resolved and I'll pick up v6. Thanks, Jonathan > > > --- > > V5: > > - None > > > > .../bindings/iio/accel/adi,adis16240.yaml | 49 +++++++++++++++++++ > > 1 file changed, 49 insertions(+) > > create mode 100644 Documentation/devicetree/bindings/iio/accel/adi,adis16240.yaml > > > > diff --git a/Documentation/devicetree/bindings/iio/accel/adi,adis16240.yaml b/Documentation/devicetree/bindings/iio/accel/adi,adis16240.yaml > > new file mode 100644 > > index 000000000000..8e902f7c49e6 > > --- /dev/null > > +++ b/Documentation/devicetree/bindings/iio/accel/adi,adis16240.yaml > > @@ -0,0 +1,49 @@ > > +# SPDX-License-Identifier: GPL-2.0 > > Dual license new bindings please: (GPL-2.0-only OR BSD-2-Clause) > > With that, > > Reviewed-by: Rob Herring <robh@kernel.org> > > > +%YAML 1.2 > > +--- > > +$id: http://devicetree.org/schemas/iio/accel/adi,adis16240.yaml# > > +$schema: http://devicetree.org/meta-schemas/core.yaml# > > + > > +title: ADIS16240 Programmable Impact Sensor and Recorder driver > > + > > +maintainers: > > + - Alexandru Ardelean <alexandru.ardelean@analog.com> > > + > > +description: | > > + ADIS16240 Programmable Impact Sensor and Recorder driver that supports > > + SPI interface. > > + https://www.analog.com/en/products/adis16240.html > > + > > +properties: > > + compatible: > > + enum: > > + - adi,adis16240 > > + > > + reg: > > + maxItems: 1 > > + > > + interrupts: > > + maxItems: 1 > > + > > +required: > > + - compatible > > + - reg > > + - interrupts > > + > > +examples: > > + - | > > + #include <dt-bindings/gpio/gpio.h> > > + #include <dt-bindings/interrupt-controller/irq.h> > > + spi0 { > > + #address-cells = <1>; > > + #size-cells = <0>; > > + > > + /* Example for a SPI device node */ > > + accelerometer@0 { > > + compatible = "adi,adis16240"; > > + reg = <0>; > > + spi-max-frequency = <2500000>; > > + interrupt-parent = <&gpio0>; > > + interrupts = <0 IRQ_TYPE_LEVEL_HIGH>; > > + }; > > + }; > > -- > > 2.24.0 > > ^ permalink raw reply [flat|nested] 7+ messages in thread
* Re: [PATCH v5 1/2] staging: iio: accel: adis16240: enforce SPI mode on probe function 2019-11-23 23:35 [PATCH v5 1/2] staging: iio: accel: adis16240: enforce SPI mode on probe function Rodrigo Carvalho 2019-11-23 23:35 ` [PATCH v5 2/2] dt-bindings: iio: accel: add binding documentation for ADIS16240 Rodrigo Carvalho @ 2019-11-25 7:55 ` Ardelean, Alexandru 2019-12-01 11:42 ` Jonathan Cameron 1 sibling, 1 reply; 7+ messages in thread From: Ardelean, Alexandru @ 2019-11-25 7:55 UTC (permalink / raw) To: Popa, Stefan Serban, gregkh, jic23, knaack.h, Hennerich, Michael, lars, rodrigorsdc, pmeerw Cc: kernel-usp, devel, devicetree, linux-kernel, linux-iio On Sat, 2019-11-23 at 20:35 -0300, Rodrigo Carvalho wrote: > [External] > > According to the datasheet, this driver supports only SPI mode 3, > so we should enforce it and call spi_setup() on probe function. > > Signed-off-by: Rodrigo Ribeiro Carvalho <rodrigorsdc@gmail.com> > --- > V5: > - Add this patch to the patchset > > drivers/staging/iio/accel/adis16240.c | 7 +++++++ > 1 file changed, 7 insertions(+) > > diff --git a/drivers/staging/iio/accel/adis16240.c > b/drivers/staging/iio/accel/adis16240.c > index 82099db4bf0c..77b6b81767b9 100644 > --- a/drivers/staging/iio/accel/adis16240.c > +++ b/drivers/staging/iio/accel/adis16240.c > @@ -400,6 +400,13 @@ static int adis16240_probe(struct spi_device *spi) > indio_dev->num_channels = ARRAY_SIZE(adis16240_channels); > indio_dev->modes = INDIO_DIRECT_MODE; > > + spi->mode = SPI_MODE_3; A generic question from me here, since I am not sure. Would this limit the configurations of this chip on the board? In case there is some level-inverter [for various weird reasons] on the board, this may not work, because the SPI controller would need CPOL to be 0. Not sure if this question is valid, or whether we need to care about such configurations. Thanks Alex > + ret = spi_setup(spi); > + if (ret) { > + dev_err(&spi->dev, "spi_setup failed!\n"); > + return ret; > + } > + > ret = adis_init(st, indio_dev, spi, &adis16240_data); > if (ret) > return ret; ^ permalink raw reply [flat|nested] 7+ messages in thread
* Re: [PATCH v5 1/2] staging: iio: accel: adis16240: enforce SPI mode on probe function 2019-11-25 7:55 ` [PATCH v5 1/2] staging: iio: accel: adis16240: enforce SPI mode on probe function Ardelean, Alexandru @ 2019-12-01 11:42 ` Jonathan Cameron 2019-12-04 7:25 ` Ardelean, Alexandru 0 siblings, 1 reply; 7+ messages in thread From: Jonathan Cameron @ 2019-12-01 11:42 UTC (permalink / raw) To: Ardelean, Alexandru Cc: Popa, Stefan Serban, gregkh, knaack.h, Hennerich, Michael, lars, rodrigorsdc, pmeerw, kernel-usp, devel, devicetree, linux-kernel, linux-iio On Mon, 25 Nov 2019 07:55:39 +0000 "Ardelean, Alexandru" <alexandru.Ardelean@analog.com> wrote: > On Sat, 2019-11-23 at 20:35 -0300, Rodrigo Carvalho wrote: > > [External] > > > > According to the datasheet, this driver supports only SPI mode 3, > > so we should enforce it and call spi_setup() on probe function. > > > > Signed-off-by: Rodrigo Ribeiro Carvalho <rodrigorsdc@gmail.com> > > --- > > V5: > > - Add this patch to the patchset > > > > drivers/staging/iio/accel/adis16240.c | 7 +++++++ > > 1 file changed, 7 insertions(+) > > > > diff --git a/drivers/staging/iio/accel/adis16240.c > > b/drivers/staging/iio/accel/adis16240.c > > index 82099db4bf0c..77b6b81767b9 100644 > > --- a/drivers/staging/iio/accel/adis16240.c > > +++ b/drivers/staging/iio/accel/adis16240.c > > @@ -400,6 +400,13 @@ static int adis16240_probe(struct spi_device *spi) > > indio_dev->num_channels = ARRAY_SIZE(adis16240_channels); > > indio_dev->modes = INDIO_DIRECT_MODE; > > > > + spi->mode = SPI_MODE_3; > > A generic question from me here, since I am not sure. > > Would this limit the configurations of this chip on the board? > In case there is some level-inverter [for various weird reasons] on the > board, this may not work, because the SPI controller would need CPOL to be > 0. > > Not sure if this question is valid, or whether we need to care about such > configurations. It's a good question as this sort of trick is used sometimes. Let's see what responses we get to the other branch of this thread before moving forwards with this. Jonathan > > Thanks > Alex > > > + ret = spi_setup(spi); > > + if (ret) { > > + dev_err(&spi->dev, "spi_setup failed!\n"); > > + return ret; > > + } > > + > > ret = adis_init(st, indio_dev, spi, &adis16240_data); > > if (ret) > > return ret; ^ permalink raw reply [flat|nested] 7+ messages in thread
* Re: [PATCH v5 1/2] staging: iio: accel: adis16240: enforce SPI mode on probe function 2019-12-01 11:42 ` Jonathan Cameron @ 2019-12-04 7:25 ` Ardelean, Alexandru 0 siblings, 0 replies; 7+ messages in thread From: Ardelean, Alexandru @ 2019-12-04 7:25 UTC (permalink / raw) To: jic23 Cc: kernel-usp, gregkh, devel, devicetree, pmeerw, knaack.h, Hennerich, Michael, lars, Popa, Stefan Serban, rodrigorsdc, linux-kernel, linux-iio On Sun, 2019-12-01 at 11:42 +0000, Jonathan Cameron wrote: > [External] > > On Mon, 25 Nov 2019 07:55:39 +0000 > "Ardelean, Alexandru" <alexandru.Ardelean@analog.com> wrote: > > > On Sat, 2019-11-23 at 20:35 -0300, Rodrigo Carvalho wrote: > > > [External] > > > > > > According to the datasheet, this driver supports only SPI mode 3, > > > so we should enforce it and call spi_setup() on probe function. > > > > > > Signed-off-by: Rodrigo Ribeiro Carvalho <rodrigorsdc@gmail.com> > > > --- > > > V5: > > > - Add this patch to the patchset > > > > > > drivers/staging/iio/accel/adis16240.c | 7 +++++++ > > > 1 file changed, 7 insertions(+) > > > > > > diff --git a/drivers/staging/iio/accel/adis16240.c > > > b/drivers/staging/iio/accel/adis16240.c > > > index 82099db4bf0c..77b6b81767b9 100644 > > > --- a/drivers/staging/iio/accel/adis16240.c > > > +++ b/drivers/staging/iio/accel/adis16240.c > > > @@ -400,6 +400,13 @@ static int adis16240_probe(struct spi_device > > > *spi) > > > indio_dev->num_channels = ARRAY_SIZE(adis16240_channels); > > > indio_dev->modes = INDIO_DIRECT_MODE; > > > > > > + spi->mode = SPI_MODE_3; > > > > A generic question from me here, since I am not sure. > > > > Would this limit the configurations of this chip on the board? > > In case there is some level-inverter [for various weird reasons] on the > > board, this may not work, because the SPI controller would need CPOL to > > be > > 0. > > > > Not sure if this question is valid, or whether we need to care about > > such > > configurations. > > It's a good question as this sort of trick is used sometimes. Let's see > what responses we get to the other branch of this thread before moving > forwards > with this. > Coming back here. Apologies to Rodrigo. I do realize that I delayed this a bit too much. Let's have this series as-is here, and then we can see about a more generic SPI Mode Converter driver that rounds-up all these weird boards. Or, if we don't do any SPI mode converter drivers, then we can handle this on a case-by-case basis/driver. > Jonathan > > > > Thanks > > Alex > > > > > + ret = spi_setup(spi); > > > + if (ret) { > > > + dev_err(&spi->dev, "spi_setup failed!\n"); > > > + return ret; > > > + } > > > + > > > ret = adis_init(st, indio_dev, spi, &adis16240_data); > > > if (ret) > > > return ret; ^ permalink raw reply [flat|nested] 7+ messages in thread
end of thread, other threads:[~2019-12-06 17:10 UTC | newest] Thread overview: 7+ messages (download: mbox.gz / follow: Atom feed) -- links below jump to the message on this page -- 2019-11-23 23:35 [PATCH v5 1/2] staging: iio: accel: adis16240: enforce SPI mode on probe function Rodrigo Carvalho 2019-11-23 23:35 ` [PATCH v5 2/2] dt-bindings: iio: accel: add binding documentation for ADIS16240 Rodrigo Carvalho 2019-12-05 15:21 ` Rob Herring 2019-12-06 17:10 ` Jonathan Cameron 2019-11-25 7:55 ` [PATCH v5 1/2] staging: iio: accel: adis16240: enforce SPI mode on probe function Ardelean, Alexandru 2019-12-01 11:42 ` Jonathan Cameron 2019-12-04 7:25 ` Ardelean, Alexandru
This is a public inbox, see mirroring instructions for how to clone and mirror all data and code used for this inbox; as well as URLs for NNTP newsgroup(s).