* [PATCH v3] ARM: dts: at91: rearrange kizbox dts using aliases nodes
@ 2019-12-05 22:30 Kamel Bouhara
2019-12-10 11:01 ` Alexandre Belloni
0 siblings, 1 reply; 2+ messages in thread
From: Kamel Bouhara @ 2019-12-05 22:30 UTC (permalink / raw)
To: Nicolas Ferre, Alexandre Belloni, Ludovic Desroches,
linux-arm-kernel, Rob Herring
Cc: devicetree, Thomas Petazzoni, Kamel Bouhara
Use aliases nodes to easy kizbox dts readability.
Signed-off-by: Kamel Bouhara <kamel.bouhara@bootlin.com>
---
Changes in v3:
- Fixed missing i2c-gpio0 label in dtsi
Changes in v2:
- Fixed some missing aliases label from dtsi
arch/arm/boot/dts/at91-kizbox.dts | 172 ++++++++++++++---------------
arch/arm/boot/dts/at91sam9260.dtsi | 4 +-
2 files changed, 86 insertions(+), 90 deletions(-)
diff --git a/arch/arm/boot/dts/at91-kizbox.dts b/arch/arm/boot/dts/at91-kizbox.dts
index 90996eaf73b2..7d938ccf71b0 100644
--- a/arch/arm/boot/dts/at91-kizbox.dts
+++ b/arch/arm/boot/dts/at91-kizbox.dts
@@ -28,85 +28,6 @@
};
};
- ahb {
- apb {
- tcb0: timer@fffa0000 {
- timer@0 {
- compatible = "atmel,tcb-timer";
- reg = <0>, <1>;
- };
-
- timer@2 {
- compatible = "atmel,tcb-timer";
- reg = <2>;
- };
- };
-
- macb0: ethernet@fffc4000 {
- phy-mode = "mii";
- pinctrl-0 = <&pinctrl_macb_rmii
- &pinctrl_macb_rmii_mii_alt>;
- status = "okay";
- };
-
- usart3: serial@fffd0000 {
- status = "okay";
- };
-
- dbgu: serial@fffff200 {
- status = "okay";
- };
-
- watchdog@fffffd40 {
- timeout-sec = <15>;
- atmel,max-heartbeat-sec = <16>;
- atmel,min-heartbeat-sec = <0>;
- status = "okay";
- };
- };
-
- usb0: ohci@500000 {
- num-ports = <1>;
- status = "okay";
- };
-
- ebi: ebi@10000000 {
- status = "okay";
-
- nand_controller: nand-controller {
- status = "okay";
- pinctrl-0 = <&pinctrl_nand_cs &pinctrl_nand_rb>;
- pinctrl-names = "default";
-
- nand@3 {
- reg = <0x3 0x0 0x800000>;
- rb-gpios = <&pioC 13 GPIO_ACTIVE_HIGH>;
- cs-gpios = <&pioC 14 GPIO_ACTIVE_HIGH>;
- nand-bus-width = <8>;
- nand-ecc-mode = "soft";
- nand-on-flash-bbt;
- label = "atmel_nand";
-
- partitions {
- compatible = "fixed-partitions";
- #address-cells = <1>;
- #size-cells = <1>;
-
- bootstrap@0 {
- label = "bootstrap";
- reg = <0x0 0x20000>;
- };
-
- ubi@20000 {
- label = "ubi";
- reg = <0x20000 0x7fe0000>;
- };
- };
- };
- };
- };
- };
-
gpio_keys {
compatible = "gpio-keys";
#address-cells = <1>;
@@ -127,15 +48,6 @@
};
};
- i2c-gpio-0 {
- status = "okay";
-
- rtc: pcf8563@51 {
- compatible = "nxp,pcf8563";
- reg = <0x51>;
- };
- };
-
pwm_leds {
compatible = "pwm-leds";
@@ -179,3 +91,87 @@
&pinctrl_tcb1_tiob0>;
};
};
+
+&tcb0 {
+ timer@0 {
+ compatible = "atmel,tcb-timer";
+ reg = <0>, <1>;
+ };
+
+ timer@2 {
+ compatible = "atmel,tcb-timer";
+ reg = <2>;
+ };
+};
+
+&ebi {
+ status = "okay";
+};
+
+&nand_controller {
+ status = "okay";
+ pinctrl-0 = <&pinctrl_nand_cs &pinctrl_nand_rb>;
+ pinctrl-names = "default";
+
+ nand@3 {
+ reg = <0x3 0x0 0x800000>;
+ rb-gpios = <&pioC 13 GPIO_ACTIVE_HIGH>;
+ cs-gpios = <&pioC 14 GPIO_ACTIVE_HIGH>;
+ nand-bus-width = <8>;
+ nand-ecc-mode = "soft";
+ nand-on-flash-bbt;
+ label = "atmel_nand";
+
+ partitions {
+ compatible = "fixed-partitions";
+ #address-cells = <1>;
+ #size-cells = <1>;
+
+ bootstrap@0 {
+ label = "bootstrap";
+ reg = <0x0 0x20000>;
+ };
+
+ ubi@20000 {
+ label = "ubi";
+ reg = <0x20000 0x7fe0000>;
+ };
+ };
+ };
+};
+
+&macb0 {
+ phy-mode = "mii";
+ pinctrl-0 = <&pinctrl_macb_rmii
+ &pinctrl_macb_rmii_mii_alt>;
+ status = "okay";
+};
+
+&usart3 {
+ status = "okay";
+};
+
+&dbgu {
+ status = "okay";
+};
+
+&watchdog {
+ timeout-sec = <15>;
+ atmel,max-heartbeat-sec = <16>;
+ atmel,min-heartbeat-sec = <0>;
+ status = "okay";
+};
+
+&usb0 {
+ num-ports = <1>;
+ status = "okay";
+};
+
+&i2c_gpio0 {
+ status = "okay";
+
+ rtc: pcf8563@51 {
+ compatible = "nxp,pcf8563";
+ reg = <0x51>;
+ };
+};
diff --git a/arch/arm/boot/dts/at91sam9260.dtsi b/arch/arm/boot/dts/at91sam9260.dtsi
index dee9c0c8a096..c5c05b723976 100644
--- a/arch/arm/boot/dts/at91sam9260.dtsi
+++ b/arch/arm/boot/dts/at91sam9260.dtsi
@@ -738,7 +738,7 @@
status = "disabled";
};
- watchdog@fffffd40 {
+ watchdog: watchdog@fffffd40 {
compatible = "atmel,at91sam9260-wdt";
reg = <0xfffffd40 0x10>;
interrupts = <1 IRQ_TYPE_LEVEL_HIGH 7>;
@@ -793,7 +793,7 @@
};
};
- i2c-gpio-0 {
+ i2c_gpio0: i2c-gpio-0 {
compatible = "i2c-gpio";
gpios = <&pioA 23 GPIO_ACTIVE_HIGH /* sda */
&pioA 24 GPIO_ACTIVE_HIGH /* scl */
--
2.24.0
^ permalink raw reply related [flat|nested] 2+ messages in thread
* Re: [PATCH v3] ARM: dts: at91: rearrange kizbox dts using aliases nodes
2019-12-05 22:30 [PATCH v3] ARM: dts: at91: rearrange kizbox dts using aliases nodes Kamel Bouhara
@ 2019-12-10 11:01 ` Alexandre Belloni
0 siblings, 0 replies; 2+ messages in thread
From: Alexandre Belloni @ 2019-12-10 11:01 UTC (permalink / raw)
To: Kamel Bouhara
Cc: Nicolas Ferre, Ludovic Desroches, linux-arm-kernel, Rob Herring,
devicetree, Thomas Petazzoni
On 05/12/2019 23:30:21+0100, Kamel Bouhara wrote:
> Use aliases nodes to easy kizbox dts readability.
>
> Signed-off-by: Kamel Bouhara <kamel.bouhara@bootlin.com>
> ---
> Changes in v3:
> - Fixed missing i2c-gpio0 label in dtsi
> Changes in v2:
> - Fixed some missing aliases label from dtsi
>
> arch/arm/boot/dts/at91-kizbox.dts | 172 ++++++++++++++---------------
> arch/arm/boot/dts/at91sam9260.dtsi | 4 +-
> 2 files changed, 86 insertions(+), 90 deletions(-)
>
Applied, thanks.
--
Alexandre Belloni, Bootlin
Embedded Linux and Kernel engineering
https://bootlin.com
^ permalink raw reply [flat|nested] 2+ messages in thread
end of thread, other threads:[~2019-12-10 11:01 UTC | newest]
Thread overview: 2+ messages (download: mbox.gz / follow: Atom feed)
-- links below jump to the message on this page --
2019-12-05 22:30 [PATCH v3] ARM: dts: at91: rearrange kizbox dts using aliases nodes Kamel Bouhara
2019-12-10 11:01 ` Alexandre Belloni
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).