* [PATCH 1/4] arm64: dts: meson: gxl: add i2c C pins
2019-12-06 10:02 [PATCH 0/4] arm64: dts: meson: add libretech-pc support Jerome Brunet
@ 2019-12-06 10:02 ` Jerome Brunet
2019-12-06 10:02 ` [PATCH 2/4] arm64: defconfig: enable FUSB302 as module Jerome Brunet
` (2 subsequent siblings)
3 siblings, 0 replies; 7+ messages in thread
From: Jerome Brunet @ 2019-12-06 10:02 UTC (permalink / raw)
To: Kevin Hilman; +Cc: Jerome Brunet, linux-amlogic, devicetree, linux-kernel
Add the DV18 and DV19 pinmux setting for the i2c C of the gxl family
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
---
arch/arm64/boot/dts/amlogic/meson-gxl.dtsi | 9 +++++++++
1 file changed, 9 insertions(+)
diff --git a/arch/arm64/boot/dts/amlogic/meson-gxl.dtsi b/arch/arm64/boot/dts/amlogic/meson-gxl.dtsi
index ed33d8efaf62..259d86399390 100644
--- a/arch/arm64/boot/dts/amlogic/meson-gxl.dtsi
+++ b/arch/arm64/boot/dts/amlogic/meson-gxl.dtsi
@@ -533,6 +533,15 @@
};
};
+ i2c_c_dv18_pins: i2c_c_dv18 {
+ mux {
+ groups = "i2c_sck_c_dv19",
+ "i2c_sda_c_dv18";
+ function = "i2c_c";
+ bias-disable;
+ };
+ };
+
eth_pins: eth_c {
mux {
groups = "eth_mdio",
--
2.23.0
^ permalink raw reply related [flat|nested] 7+ messages in thread
* [PATCH 2/4] arm64: defconfig: enable FUSB302 as module
2019-12-06 10:02 [PATCH 0/4] arm64: dts: meson: add libretech-pc support Jerome Brunet
2019-12-06 10:02 ` [PATCH 1/4] arm64: dts: meson: gxl: add i2c C pins Jerome Brunet
@ 2019-12-06 10:02 ` Jerome Brunet
2019-12-06 10:02 ` [PATCH 3/4] dt-bindings: arm: amlogic: add libretech-pc bindings Jerome Brunet
2019-12-06 10:02 ` [PATCH 4/4] arm64: dts: meson: add libretech-pc boards support Jerome Brunet
3 siblings, 0 replies; 7+ messages in thread
From: Jerome Brunet @ 2019-12-06 10:02 UTC (permalink / raw)
To: Kevin Hilman; +Cc: Jerome Brunet, linux-amlogic, devicetree, linux-kernel
Enable the type C fusb302 driver as module
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
---
arch/arm64/configs/defconfig | 2 ++
1 file changed, 2 insertions(+)
diff --git a/arch/arm64/configs/defconfig b/arch/arm64/configs/defconfig
index 47d1b8fb1969..5ccb2100db92 100644
--- a/arch/arm64/configs/defconfig
+++ b/arch/arm64/configs/defconfig
@@ -618,6 +618,8 @@ CONFIG_USB_GADGET=y
CONFIG_USB_RENESAS_USBHS_UDC=m
CONFIG_USB_RENESAS_USB3=m
CONFIG_TYPEC=m
+CONFIG_TYPEC_TCPM=m
+CONFIG_TYPEC_FUSB302=m
CONFIG_TYPEC_HD3SS3220=m
CONFIG_MMC=y
CONFIG_MMC_BLOCK_MINORS=32
--
2.23.0
^ permalink raw reply related [flat|nested] 7+ messages in thread
* [PATCH 3/4] dt-bindings: arm: amlogic: add libretech-pc bindings
2019-12-06 10:02 [PATCH 0/4] arm64: dts: meson: add libretech-pc support Jerome Brunet
2019-12-06 10:02 ` [PATCH 1/4] arm64: dts: meson: gxl: add i2c C pins Jerome Brunet
2019-12-06 10:02 ` [PATCH 2/4] arm64: defconfig: enable FUSB302 as module Jerome Brunet
@ 2019-12-06 10:02 ` Jerome Brunet
2019-12-06 10:02 ` [PATCH 4/4] arm64: dts: meson: add libretech-pc boards support Jerome Brunet
3 siblings, 0 replies; 7+ messages in thread
From: Jerome Brunet @ 2019-12-06 10:02 UTC (permalink / raw)
To: Kevin Hilman; +Cc: Jerome Brunet, linux-amlogic, devicetree, linux-kernel
Add the board bindings for the libretech PC form factor
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
---
Documentation/devicetree/bindings/arm/amlogic.yaml | 2 ++
1 file changed, 2 insertions(+)
diff --git a/Documentation/devicetree/bindings/arm/amlogic.yaml b/Documentation/devicetree/bindings/arm/amlogic.yaml
index c6a443352ef8..2660ba3b129b 100644
--- a/Documentation/devicetree/bindings/arm/amlogic.yaml
+++ b/Documentation/devicetree/bindings/arm/amlogic.yaml
@@ -104,6 +104,7 @@ properties:
- enum:
- amlogic,p230
- amlogic,p231
+ - libretech,aml-s905d-pc
- phicomm,n1
- const: amlogic,s905d
- const: amlogic,meson-gxl
@@ -115,6 +116,7 @@ properties:
- amlogic,q201
- khadas,vim2
- kingnovel,r-box-pro
+ - libretech,aml-s912-pc
- nexbox,a1
- tronsmart,vega-s96
- const: amlogic,s912
--
2.23.0
^ permalink raw reply related [flat|nested] 7+ messages in thread
* [PATCH 4/4] arm64: dts: meson: add libretech-pc boards support
2019-12-06 10:02 [PATCH 0/4] arm64: dts: meson: add libretech-pc support Jerome Brunet
` (2 preceding siblings ...)
2019-12-06 10:02 ` [PATCH 3/4] dt-bindings: arm: amlogic: add libretech-pc bindings Jerome Brunet
@ 2019-12-06 10:02 ` Jerome Brunet
2019-12-08 18:05 ` Martin Blumenstingl
3 siblings, 1 reply; 7+ messages in thread
From: Jerome Brunet @ 2019-12-06 10:02 UTC (permalink / raw)
To: Kevin Hilman; +Cc: Jerome Brunet, linux-amlogic, devicetree, linux-kernel
Add support for the the amlogic libretech-pc platform, aka tartiflette.
There is 2 variants of the platform, one with the s905d, the other with
the s912.
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
---
arch/arm64/boot/dts/amlogic/Makefile | 2 +
.../dts/amlogic/meson-gx-libretech-pc.dtsi | 362 ++++++++++++++++++
.../amlogic/meson-gxl-s905d-libretech-pc.dts | 16 +
.../amlogic/meson-gxm-s912-libretech-pc.dts | 63 +++
4 files changed, 443 insertions(+)
create mode 100644 arch/arm64/boot/dts/amlogic/meson-gx-libretech-pc.dtsi
create mode 100644 arch/arm64/boot/dts/amlogic/meson-gxl-s905d-libretech-pc.dts
create mode 100644 arch/arm64/boot/dts/amlogic/meson-gxm-s912-libretech-pc.dts
diff --git a/arch/arm64/boot/dts/amlogic/Makefile b/arch/arm64/boot/dts/amlogic/Makefile
index 63400538d39f..6071a4081eb2 100644
--- a/arch/arm64/boot/dts/amlogic/Makefile
+++ b/arch/arm64/boot/dts/amlogic/Makefile
@@ -29,11 +29,13 @@ dtb-$(CONFIG_ARCH_MESON) += meson-gxl-s905d-phicomm-n1.dtb
dtb-$(CONFIG_ARCH_MESON) += meson-gxl-s805x-p241.dtb
dtb-$(CONFIG_ARCH_MESON) += meson-gxl-s905w-p281.dtb
dtb-$(CONFIG_ARCH_MESON) += meson-gxl-s905w-tx3-mini.dtb
+dtb-$(CONFIG_ARCH_MESON) += meson-gxl-s905d-libretech-pc.dtb
dtb-$(CONFIG_ARCH_MESON) += meson-gxm-khadas-vim2.dtb
dtb-$(CONFIG_ARCH_MESON) += meson-gxm-nexbox-a1.dtb
dtb-$(CONFIG_ARCH_MESON) += meson-gxm-q200.dtb
dtb-$(CONFIG_ARCH_MESON) += meson-gxm-q201.dtb
dtb-$(CONFIG_ARCH_MESON) += meson-gxm-rbox-pro.dtb
+dtb-$(CONFIG_ARCH_MESON) += meson-gxm-s912-libretech-pc.dtb
dtb-$(CONFIG_ARCH_MESON) += meson-gxm-vega-s96.dtb
dtb-$(CONFIG_ARCH_MESON) += meson-sm1-sei610.dtb
dtb-$(CONFIG_ARCH_MESON) += meson-sm1-khadas-vim3l.dtb
diff --git a/arch/arm64/boot/dts/amlogic/meson-gx-libretech-pc.dtsi b/arch/arm64/boot/dts/amlogic/meson-gx-libretech-pc.dtsi
new file mode 100644
index 000000000000..cf0a02b0e0a2
--- /dev/null
+++ b/arch/arm64/boot/dts/amlogic/meson-gx-libretech-pc.dtsi
@@ -0,0 +1,362 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Copyright (c) 2019 BayLibre SAS.
+ * Author: Jerome Brunet <jbrunet@baylibre.com>
+ */
+
+/* Libretech Amlogic GX PC form factor - AKA: Tartiflette */
+
+#include <dt-bindings/input/input.h>
+
+/ {
+ adc_keys {
+ compatible = "adc-keys";
+ io-channels = <&saradc 0>;
+ io-channel-names = "buttons";
+ keyup-threshold-microvolt = <1800000>;
+
+ button-onoff {
+ label = "On/Off";
+ linux,code = <KEY_VENDOR>;
+ press-threshold-microvolt = <1300000>;
+ };
+ };
+
+ aliases {
+ serial0 = &uart_AO;
+ ethernet0 = ðmac;
+ spi0 = &spifc;
+ };
+
+ chosen {
+ stdout-path = "serial0:115200n8";
+ };
+
+ cvbs-connector {
+ compatible = "composite-video-connector";
+ status = "disabled";
+
+ port {
+ cvbs_connector_in: endpoint {
+ remote-endpoint = <&cvbs_vdac_out>;
+ };
+ };
+ };
+
+ emmc_pwrseq: emmc-pwrseq {
+ compatible = "mmc-pwrseq-emmc";
+ reset-gpios = <&gpio BOOT_9 GPIO_ACTIVE_LOW>;
+ };
+
+ hdmi-connector {
+ compatible = "hdmi-connector";
+ type = "a";
+
+ port {
+ hdmi_connector_in: endpoint {
+ remote-endpoint = <&hdmi_tx_tmds_out>;
+ };
+ };
+ };
+
+ gpio-keys-polled {
+ compatible = "gpio-keys-polled";
+ poll-interval = <100>;
+
+ power-button {
+ label = "power";
+ linux,code = <KEY_POWER>;
+ gpios = <&gpio_ao GPIOAO_2 GPIO_ACTIVE_LOW>;
+ };
+ };
+
+ memory@0 {
+ device_type = "memory";
+ reg = <0x0 0x0 0x0 0x80000000>;
+ };
+
+ ao_5v: regulator-ao_5v {
+ compatible = "regulator-fixed";
+ regulator-name = "AO_5V";
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ vin-supply = <&dc_in>;
+ regulator-always-on;
+ };
+
+ dc_in: regulator-dc_in {
+ compatible = "regulator-fixed";
+ regulator-name = "DC_IN";
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ regulator-always-on;
+ };
+
+ leds {
+ compatible = "gpio-leds";
+
+ green {
+ label = "librecomputer:green:disk";
+ gpios = <&gpio_ao GPIOAO_9 GPIO_ACTIVE_HIGH>;
+ linux,default-trigger = "disk-activity";
+ };
+
+ blue {
+ label = "librecomputer:blue:cpu";
+ gpios = <&gpio GPIODV_28 GPIO_ACTIVE_HIGH>;
+ linux,default-trigger = "heartbeat";
+ panic-indicator;
+ };
+ };
+
+ vcc_card: regulator-vcc_card {
+ compatible = "regulator-fixed";
+ regulator-name = "VCC_CARD";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ vin-supply = <&vddio_ao3v3>;
+
+ gpio = <&gpio GPIODV_4 GPIO_ACTIVE_HIGH>;
+ enable-active-high;
+ };
+
+ vcc5v: regulator-vcc5v {
+ compatible = "regulator-fixed";
+ regulator-name = "VCC5V";
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ vin-supply = <&ao_5v>;
+
+ gpio = <&gpio GPIOH_3 GPIO_OPEN_DRAIN>;
+ };
+
+ vddio_ao18: regulator-vddio_ao18 {
+ compatible = "regulator-fixed";
+ regulator-name = "VDDIO_AO18";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ vin-supply = <&ao_5v>;
+ regulator-always-on;
+ };
+
+ vddio_ao3v3: regulator-vddio_ao3v3 {
+ compatible = "regulator-fixed";
+ regulator-name = "VDDIO_AO3V3";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ vin-supply = <&ao_5v>;
+ regulator-always-on;
+ };
+
+ vddio_boot: regulator-vddio_boot {
+ compatible = "regulator-fixed";
+ regulator-name = "VDDIO_BOOT";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ vin-supply = <&vddio_ao3v3>;
+ regulator-always-on;
+ };
+
+ vddio_card: regulator-vddio-card {
+ compatible = "regulator-gpio";
+ regulator-name = "VDDIO_CARD";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <3300000>;
+
+ gpios = <&gpio GPIODV_5 GPIO_ACTIVE_HIGH>;
+ gpios-states = <0>;
+
+ states = <3300000 0>,
+ <1800000 1>;
+
+ regulator-settling-time-up-us = <200>;
+ regulator-settling-time-down-us = <50000>;
+ };
+};
+
+&cec_AO {
+ pinctrl-0 = <&ao_cec_pins>;
+ pinctrl-names = "default";
+ hdmi-phandle = <&hdmi_tx>;
+ status = "okay";
+};
+
+&cvbs_vdac_port {
+ cvbs_vdac_out: endpoint {
+ remote-endpoint = <&cvbs_connector_in>;
+ };
+};
+
+ðmac {
+ pinctrl-0 = <ð_pins>;
+ pinctrl-names = "default";
+ phy-handle = <&external_phy>;
+ amlogic,tx-delay-ns = <2>;
+ phy-mode = "rgmii";
+ status = "okay";
+};
+
+&external_mdio {
+ external_phy: ethernet-phy@0 {
+ reg = <0>;
+ max-speed = <1000>;
+ reset-assert-us = <10000>;
+ reset-deassert-us = <30000>;
+ reset-gpios = <&gpio GPIOZ_14 GPIO_ACTIVE_LOW>;
+ interrupt-parent = <&gpio_intc>;
+ interrupts = <25 IRQ_TYPE_LEVEL_LOW>;
+ };
+};
+
+&pinctrl_periphs {
+ /*
+ * Make sure the reset pin of the usb HUB is driven high to take
+ * it out of reset.
+ */
+ usb1_rst_pins: usb1_rst_irq {
+ mux {
+ groups = "GPIODV_3";
+ function = "gpio_periphs";
+ bias-disable;
+ output-high;
+ };
+ };
+};
+
+&hdmi_tx {
+ pinctrl-0 = <&hdmi_hpd_pins>, <&hdmi_i2c_pins>;
+ pinctrl-names = "default";
+ hdmi-supply = <&vcc5v>;
+ status = "okay";
+};
+
+&hdmi_tx_tmds_port {
+ hdmi_tx_tmds_out: endpoint {
+ remote-endpoint = <&hdmi_connector_in>;
+ };
+};
+
+&ir {
+ pinctrl-0 = <&remote_input_ao_pins>;
+ pinctrl-names = "default";
+ status = "okay";
+};
+
+&i2c_C {
+ pinctrl-0 = <&i2c_c_dv18_pins>;
+ pinctrl-names = "default";
+ status = "okay";
+
+ rtc: rtc@51 {
+ reg = <0x51>;
+ compatible = "nxp,pcf8563";
+ #clock-cells = <0>;
+ clock-output-names = "rtc_clkout";
+ };
+};
+
+&pwm_AO_ab {
+ pinctrl-0 = <&pwm_ao_a_3_pins>;
+ pinctrl-names = "default";
+ clocks = <&clkc CLKID_FCLK_DIV4>;
+ clock-names = "clkin0";
+ status = "okay";
+};
+
+&pwm_ab {
+ pinctrl-0 = <&pwm_b_pins>;
+ pinctrl-names = "default";
+ clocks = <&clkc CLKID_FCLK_DIV4>;
+ clock-names = "clkin0";
+ status = "okay";
+};
+
+&pwm_ef {
+ pinctrl-0 = <&pwm_e_pins>, <&pwm_f_clk_pins>;
+ pinctrl-names = "default";
+ clocks = <&clkc CLKID_FCLK_DIV4>;
+ clock-names = "clkin0";
+ status = "okay";
+};
+
+&saradc {
+ vref-supply = <&vddio_ao18>;
+ status = "okay";
+};
+
+/* SD card */
+&sd_emmc_b {
+ pinctrl-0 = <&sdcard_pins>;
+ pinctrl-1 = <&sdcard_clk_gate_pins>;
+ pinctrl-names = "default", "clk-gate";
+
+ bus-width = <4>;
+ cap-sd-highspeed;
+ sd-uhs-sdr12;
+ sd-uhs-sdr25;
+ sd-uhs-sdr50;
+ sd-uhs-ddr50;
+ max-frequency = <200000000>;
+ disable-wp;
+
+ cd-gpios = <&gpio CARD_6 GPIO_ACTIVE_LOW>;
+
+ vmmc-supply = <&vcc_card>;
+ vqmmc-supply = <&vddio_card>;
+
+ status = "okay";
+};
+
+/* eMMC */
+&sd_emmc_c {
+ pinctrl-0 = <&emmc_pins>;
+ pinctrl-1 = <&emmc_clk_gate_pins>;
+ pinctrl-names = "default", "clk-gate";
+
+ bus-width = <8>;
+ cap-mmc-highspeed;
+ mmc-ddr-1_8v;
+ mmc-hs200-1_8v;
+ max-frequency = <200000000>;
+ disable-wp;
+
+ mmc-pwrseq = <&emmc_pwrseq>;
+ vmmc-supply = <&vddio_ao3v3>;
+ vqmmc-supply = <&vddio_boot>;
+
+ status = "okay";
+};
+
+&spifc {
+ pinctrl-0 = <&nor_pins>;
+ pinctrl-names = "default";
+ status = "okay";
+
+ gd25lq128: spi-flash@0 {
+ compatible = "jedec,spi-nor";
+ #address-cells = <1>;
+ #size-cells = <1>;
+ reg = <0>;
+ spi-max-frequency = <12000000>;
+ };
+};
+
+&uart_AO {
+ pinctrl-0 = <&uart_ao_a_pins>;
+ pinctrl-names = "default";
+ status = "okay";
+};
+
+&usb0 {
+ status = "okay";
+};
+
+&usb2_phy0 {
+ pinctrl-0 = <&usb1_rst_pins>;
+ pinctrl-names = "default";
+ phy-supply = <&vcc5v>;
+};
+
+&usb2_phy1 {
+ phy-supply = <&vcc5v>;
+};
diff --git a/arch/arm64/boot/dts/amlogic/meson-gxl-s905d-libretech-pc.dts b/arch/arm64/boot/dts/amlogic/meson-gxl-s905d-libretech-pc.dts
new file mode 100644
index 000000000000..100a1cfeea15
--- /dev/null
+++ b/arch/arm64/boot/dts/amlogic/meson-gxl-s905d-libretech-pc.dts
@@ -0,0 +1,16 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Copyright (c) 2019 BayLibre SAS. All rights reserved.
+ * Author: Jerome Brunet <jbrunet@baylibre.com>
+ */
+
+/dts-v1/;
+
+#include "meson-gxl-s905d.dtsi"
+#include "meson-gx-libretech-pc.dtsi"
+
+/ {
+ compatible = "libretech,aml-s905d-pc", "amlogic,s905d",
+ "amlogic,meson-gxl";
+ model = "Libre Computer AML-S905D-PC";
+};
diff --git a/arch/arm64/boot/dts/amlogic/meson-gxm-s912-libretech-pc.dts b/arch/arm64/boot/dts/amlogic/meson-gxm-s912-libretech-pc.dts
new file mode 100644
index 000000000000..fa2d2b25861c
--- /dev/null
+++ b/arch/arm64/boot/dts/amlogic/meson-gxm-s912-libretech-pc.dts
@@ -0,0 +1,63 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Copyright (c) 2019 BayLibre SAS. All rights reserved.
+ * Author: Jerome Brunet <jbrunet@baylibre.com>
+ */
+
+/dts-v1/;
+
+#include "meson-gxm.dtsi"
+#include "meson-gx-libretech-pc.dtsi"
+
+/ {
+ compatible = "libretech,aml-s912-pc", "amlogic,s912",
+ "amlogic,meson-gxm";
+ model = "Libre Computer AML-S912-PC";
+
+ typec2_vbus: regulator-typec2_vbus {
+ compatible = "regulator-fixed";
+ regulator-name = "TYPEC2_VBUS";
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ vin-supply = <&vcc5v>;
+
+ gpio = <&gpio GPIODV_1 GPIO_ACTIVE_HIGH>;
+ enable-active-high;
+ };
+};
+
+&pinctrl_periphs {
+ /*
+ * Make sure the irq pin of the TYPE C controller is not driven
+ * by the SoC.
+ */
+ fusb302_irq_pins: fusb302_irq {
+ mux {
+ groups = "GPIODV_0";
+ function = "gpio_periphs";
+ bias-pull-up;
+ output-disable;
+ };
+ };
+};
+
+&i2c_C {
+ fusb302@22 {
+ compatible = "fcs,fusb302";
+ reg = <0x22>;
+
+ pinctrl-0 = <&fusb302_irq_pins>;
+ pinctrl-names = "default";
+
+ interrupt-parent = <&gpio_intc>;
+ interrupts = <59 IRQ_TYPE_LEVEL_LOW>;
+
+ vbus-supply = <&typec2_vbus>;
+
+ status = "okay";
+ };
+};
+
+&usb2_phy2 {
+ phy-supply = <&typec2_vbus>;
+};
--
2.23.0
^ permalink raw reply related [flat|nested] 7+ messages in thread
* Re: [PATCH 4/4] arm64: dts: meson: add libretech-pc boards support
2019-12-06 10:02 ` [PATCH 4/4] arm64: dts: meson: add libretech-pc boards support Jerome Brunet
@ 2019-12-08 18:05 ` Martin Blumenstingl
2019-12-09 10:15 ` Jerome Brunet
0 siblings, 1 reply; 7+ messages in thread
From: Martin Blumenstingl @ 2019-12-08 18:05 UTC (permalink / raw)
To: Jerome Brunet; +Cc: Kevin Hilman, linux-amlogic, devicetree, linux-kernel
Hi Jerome,
this is looking good overall - I have some questions / nit-picks below
On Fri, Dec 6, 2019 at 11:02 AM Jerome Brunet <jbrunet@baylibre.com> wrote:
[...]
> + adc_keys {
on most boards we use "adc-keys" instead of "adc_keys"
[...]
> + button-onoff {
> + label = "On/Off";
> + linux,code = <KEY_VENDOR>;
based on the label I assumed that the code is KEY_POWER
why is KEY_VENDOR the better choice here?
[...]
> + cvbs-connector {
> + compatible = "composite-video-connector";
> + status = "disabled";
is there CVBS on the board? if I remember correctly the VPU driver
works fine when omitting the CVBS connector
so if the board doesn't have it you may drop the whole node instead of
keeping it disabled
[...]
> + leds {
> + compatible = "gpio-leds";
> +
> + green {
> + label = "librecomputer:green:disk";
you can use the "function" and "color" properties instead of the (now
deprecated) "label"
[...]
> +&external_mdio {
> + external_phy: ethernet-phy@0 {
> + reg = <0>;
it would be great to have a comment above which PHY is used on this board
> + max-speed = <1000>;
> + reset-assert-us = <10000>;
> + reset-deassert-us = <30000>;
> + reset-gpios = <&gpio GPIOZ_14 GPIO_ACTIVE_LOW>;
> + interrupt-parent = <&gpio_intc>;
a comment like /* MAC_INTR on GPIOZ_15 */ would be great here
> + interrupts = <25 IRQ_TYPE_LEVEL_LOW>;
[...]
> +&pinctrl_periphs {
> + /*
> + * Make sure the reset pin of the usb HUB is driven high to take
> + * it out of reset.
> + */
> + usb1_rst_pins: usb1_rst_irq {
> + mux {
> + groups = "GPIODV_3";
> + function = "gpio_periphs";
> + bias-disable;
> + output-high;
> + };
> + };
on other boards (like Odroid-C2) we use a GPIO hog for this. I'm not
sure which one is better
[...]
> +&pinctrl_periphs {
> + /*
> + * Make sure the irq pin of the TYPE C controller is not driven
> + * by the SoC.
is this because the SoC default configuration pulls the IRQ line LOW,
which then generates "phantom" IRQs?
[...]
> + fusb302@22 {
typec-portc@22
[...]
> + interrupt-parent = <&gpio_intc>;
> + interrupts = <59 IRQ_TYPE_LEVEL_LOW>;
a comment above with the GPIO number would be great
Martin
^ permalink raw reply [flat|nested] 7+ messages in thread
* Re: [PATCH 4/4] arm64: dts: meson: add libretech-pc boards support
2019-12-08 18:05 ` Martin Blumenstingl
@ 2019-12-09 10:15 ` Jerome Brunet
0 siblings, 0 replies; 7+ messages in thread
From: Jerome Brunet @ 2019-12-09 10:15 UTC (permalink / raw)
To: Martin Blumenstingl; +Cc: Kevin Hilman, linux-amlogic, devicetree, linux-kernel
On Sun 08 Dec 2019 at 19:05, Martin Blumenstingl <martin.blumenstingl@googlemail.com> wrote:
> Hi Jerome,
>
> this is looking good overall - I have some questions / nit-picks below
>
> On Fri, Dec 6, 2019 at 11:02 AM Jerome Brunet <jbrunet@baylibre.com> wrote:
> [...]
>> + adc_keys {
> on most boards we use "adc-keys" instead of "adc_keys"
>
> [...]
>> + button-onoff {
>> + label = "On/Off";
>> + linux,code = <KEY_VENDOR>;
> based on the label I assumed that the code is KEY_POWER
> why is KEY_VENDOR the better choice here?
>
My bad - The button is labeled with "UPDATE" ... nothing really matches
in the KEYs ... so VENDOR it is.
I have just copy/pasted the section and forgot to update the rest
> [...]
>> + cvbs-connector {
>> + compatible = "composite-video-connector";
>> + status = "disabled";
> is there CVBS on the board? if I remember correctly the VPU driver
> works fine when omitting the CVBS connector
> so if the board doesn't have it you may drop the whole node instead of
> keeping it disabled
The CVBS output could be provided on one the GPIO header.
Since it is not really standard, I prefer to keep off and leave to
option to easily turn it on if someone wants to use it.
I'll had a comment for that.
>
> [...]
>> + leds {
>> + compatible = "gpio-leds";
>> +
>> + green {
>> + label = "librecomputer:green:disk";
> you can use the "function" and "color" properties instead of the (now
> deprecated) "label"
>
> [...]
>> +&external_mdio {
>> + external_phy: ethernet-phy@0 {
>> + reg = <0>;
> it would be great to have a comment above which PHY is used on this board
>
>> + max-speed = <1000>;
>> + reset-assert-us = <10000>;
>> + reset-deassert-us = <30000>;
>> + reset-gpios = <&gpio GPIOZ_14 GPIO_ACTIVE_LOW>;
>> + interrupt-parent = <&gpio_intc>;
> a comment like /* MAC_INTR on GPIOZ_15 */ would be great here
>> + interrupts = <25 IRQ_TYPE_LEVEL_LOW>;
>
> [...]
>> +&pinctrl_periphs {
>> + /*
>> + * Make sure the reset pin of the usb HUB is driven high to take
>> + * it out of reset.
>> + */
>> + usb1_rst_pins: usb1_rst_irq {
>> + mux {
>> + groups = "GPIODV_3";
>> + function = "gpio_periphs";
>> + bias-disable;
>> + output-high;
>> + };
>> + };
> on other boards (like Odroid-C2) we use a GPIO hog for this. I'm not
> sure which one is better
>
This is at least tied to the related device.
I have discussed "hog" vs "pinctrl" matter with Bartosz Golaszewski and
we could not find any reason not proceed with pinctrl when possible.
> [...]
>> +&pinctrl_periphs {
>> + /*
>> + * Make sure the irq pin of the TYPE C controller is not driven
>> + * by the SoC.
> is this because the SoC default configuration pulls the IRQ line LOW,
> which then generates "phantom" IRQs?
No. It is just making sure the pin is claimed and properly configured.
Since our interrupt and gpio controller are completly de-coupled it is
not necessarily the case without it (... and yes, the same is true for the
other device using gpio irqs)
>
> [...]
>> + fusb302@22 {
> typec-portc@22
>
> [...]
>> + interrupt-parent = <&gpio_intc>;
>> + interrupts = <59 IRQ_TYPE_LEVEL_LOW>;
> a comment above with the GPIO number would be great
>
>
> Martin
^ permalink raw reply [flat|nested] 7+ messages in thread