devicetree.vger.kernel.org archive mirror
 help / color / mirror / Atom feed
From: Peng Ma <peng.ma@nxp.com>
To: "vkoul@kernel.org" <vkoul@kernel.org>,
	"robh+dt@kernel.org" <robh+dt@kernel.org>,
	"mark.rutland@arm.com" <mark.rutland@arm.com>,
	"shawnguo@kernel.org" <shawnguo@kernel.org>,
	Leo Li <leoyang.li@nxp.com>,
	"dan.j.williams@intel.com" <dan.j.williams@intel.com>,
	Robin Gong <yibin.gong@nxp.com>
Cc: "dmaengine@vger.kernel.org" <dmaengine@vger.kernel.org>,
	"devicetree@vger.kernel.org" <devicetree@vger.kernel.org>,
	"linux-kernel@vger.kernel.org" <linux-kernel@vger.kernel.org>,
	"linux-arm-kernel@lists.infradead.org" 
	<linux-arm-kernel@lists.infradead.org>, Peng Ma <peng.ma@nxp.com>
Subject: [v4 1/2] dmaengine: fsl-edma: Add eDMA support for QorIQ LS1028A platform
Date: Wed, 11 Dec 2019 08:09:33 +0000	[thread overview]
Message-ID: <20191211080749.30751-1-peng.ma@nxp.com> (raw)

Our platforms(such as LS1021A, LS1012A, LS1043A, LS1046A, LS1028A) with
below registers(CHCFG0 - CHCFG15) of eDMA as follows:
*-----------------------------------------------------------*
|     Offset   |	OTHERS      |		LS1028A	    |
|--------------|--------------------|-----------------------|
|     0x0      |        CHCFG0      |           CHCFG3      |
|--------------|--------------------|-----------------------|
|     0x1      |        CHCFG1      |           CHCFG2      |
|--------------|--------------------|-----------------------|
|     0x2      |        CHCFG2      |           CHCFG1      |
|--------------|--------------------|-----------------------|
|     0x3      |        CHCFG3      |           CHCFG0      |
|--------------|--------------------|-----------------------|
|     ...      |        ......      |           ......      |
|--------------|--------------------|-----------------------|
|     0xC      |        CHCFG12     |           CHCFG15     |
|--------------|--------------------|-----------------------|
|     0xD      |        CHCFG13     |           CHCFG14     |
|--------------|--------------------|-----------------------|
|     0xE      |        CHCFG14     |           CHCFG13     |
|--------------|--------------------|-----------------------|
|     0xF      |        CHCFG15     |           CHCFG12     |
*-----------------------------------------------------------*

This patch is to improve edma driver to fit LS1028A platform.

Signed-off-by: Peng Ma <peng.ma@nxp.com>
---
Changed for v4:
	- Add 'mux_swap' into 'struct fsl_edma_drvdata'
	- Remove soc match function  

 drivers/dma/fsl-edma-common.c | 5 +++++
 drivers/dma/fsl-edma-common.h | 1 +
 drivers/dma/fsl-edma.c        | 8 ++++++++
 3 files changed, 14 insertions(+)

diff --git a/drivers/dma/fsl-edma-common.c b/drivers/dma/fsl-edma-common.c
index b1a7ca91701a..5697c3622699 100644
--- a/drivers/dma/fsl-edma-common.c
+++ b/drivers/dma/fsl-edma-common.c
@@ -109,10 +109,15 @@ void fsl_edma_chan_mux(struct fsl_edma_chan *fsl_chan,
 	u32 ch = fsl_chan->vchan.chan.chan_id;
 	void __iomem *muxaddr;
 	unsigned int chans_per_mux, ch_off;
+	int endian_diff[4] = {3, 1, -1, -3};
 	u32 dmamux_nr = fsl_chan->edma->drvdata->dmamuxs;
 
 	chans_per_mux = fsl_chan->edma->n_chans / dmamux_nr;
 	ch_off = fsl_chan->vchan.chan.chan_id % chans_per_mux;
+
+	if (fsl_chan->edma->drvdata->mux_swap)
+		ch_off += endian_diff[ch_off % 4];
+
 	muxaddr = fsl_chan->edma->muxbase[ch / chans_per_mux];
 	slot = EDMAMUX_CHCFG_SOURCE(slot);
 
diff --git a/drivers/dma/fsl-edma-common.h b/drivers/dma/fsl-edma-common.h
index 5eaa2902ed39..67e422590c9a 100644
--- a/drivers/dma/fsl-edma-common.h
+++ b/drivers/dma/fsl-edma-common.h
@@ -147,6 +147,7 @@ struct fsl_edma_drvdata {
 	enum edma_version	version;
 	u32			dmamuxs;
 	bool			has_dmaclk;
+	bool			mux_swap;
 	int			(*setup_irq)(struct platform_device *pdev,
 					     struct fsl_edma_engine *fsl_edma);
 };
diff --git a/drivers/dma/fsl-edma.c b/drivers/dma/fsl-edma.c
index b626c06ac2e0..eff7ebd8cf35 100644
--- a/drivers/dma/fsl-edma.c
+++ b/drivers/dma/fsl-edma.c
@@ -233,6 +233,13 @@ static struct fsl_edma_drvdata vf610_data = {
 	.setup_irq = fsl_edma_irq_init,
 };
 
+static struct fsl_edma_drvdata ls1028a_data = {
+	.version = v1,
+	.dmamuxs = DMAMUX_NR,
+	.mux_swap = true,
+	.setup_irq = fsl_edma_irq_init,
+};
+
 static struct fsl_edma_drvdata imx7ulp_data = {
 	.version = v3,
 	.dmamuxs = 1,
@@ -242,6 +249,7 @@ static struct fsl_edma_drvdata imx7ulp_data = {
 
 static const struct of_device_id fsl_edma_dt_ids[] = {
 	{ .compatible = "fsl,vf610-edma", .data = &vf610_data},
+	{ .compatible = "fsl,ls1028a-edma", .data = &ls1028a_data},
 	{ .compatible = "fsl,imx7ulp-edma", .data = &imx7ulp_data},
 	{ /* sentinel */ }
 };
-- 
2.17.1


             reply	other threads:[~2019-12-11  8:09 UTC|newest]

Thread overview: 4+ messages / expand[flat|nested]  mbox.gz  Atom feed  top
2019-12-11  8:09 Peng Ma [this message]
2019-12-11  8:09 ` [v4 2/2] arm64: dts: ls1028a: Update edma compatible to fit eDMA driver Peng Ma
2019-12-12  2:19   ` Shawn Guo
2019-12-12  1:56 ` [v4 1/2] dmaengine: fsl-edma: Add eDMA support for QorIQ LS1028A platform Robin Gong

Reply instructions:

You may reply publicly to this message via plain-text email
using any one of the following methods:

* Save the following mbox file, import it into your mail client,
  and reply-to-all from there: mbox

  Avoid top-posting and favor interleaved quoting:
  https://en.wikipedia.org/wiki/Posting_style#Interleaved_style

* Reply using the --to, --cc, and --in-reply-to
  switches of git-send-email(1):

  git send-email \
    --in-reply-to=20191211080749.30751-1-peng.ma@nxp.com \
    --to=peng.ma@nxp.com \
    --cc=dan.j.williams@intel.com \
    --cc=devicetree@vger.kernel.org \
    --cc=dmaengine@vger.kernel.org \
    --cc=leoyang.li@nxp.com \
    --cc=linux-arm-kernel@lists.infradead.org \
    --cc=linux-kernel@vger.kernel.org \
    --cc=mark.rutland@arm.com \
    --cc=robh+dt@kernel.org \
    --cc=shawnguo@kernel.org \
    --cc=vkoul@kernel.org \
    --cc=yibin.gong@nxp.com \
    /path/to/YOUR_REPLY

  https://kernel.org/pub/software/scm/git/docs/git-send-email.html

* If your mail client supports setting the In-Reply-To header
  via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line before the message body. 
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).