[PATCH AUTOSEL 4.14 066/186] arm: dts: allwinner: H3: Add PMU node

[PATCH AUTOSEL 4.14 066/186] arm: dts: allwinner: H3: Add PMU node

[Sasha Levin]

From: Andre Przywara <andre.przywara@arm.com>

[ Upstream commit 0388a110747bec0c9d9de995842bb2a03a26aae1 ]

Add the Performance Monitoring Unit (PMU) device tree node to the H3
.dtsi, which tells DT users which interrupts are triggered by PMU
overflow events on each core. The numbers come from the manual and have
been checked in U-Boot and with perf in Linux.

Tested with perf record and taskset on an OrangePi Zero.

Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 arch/arm/boot/dts/sun8i-h3.dtsi | 15 ++++++++++++---
 1 file changed, 12 insertions(+), 3 deletions(-)

diff --git a/arch/arm/boot/dts/sun8i-h3.dtsi b/arch/arm/boot/dts/sun8i-h3.dtsi
index b36f9f423c39d..d685beb49659c 100644
--- a/arch/arm/boot/dts/sun8i-h3.dtsi
+++ b/arch/arm/boot/dts/sun8i-h3.dtsi
@@ -53,25 +53,34 @@
 			reg = <0>;
 		};
 
-		cpu@1 {
+		cpu1: cpu@1 {
 			compatible = "arm,cortex-a7";
 			device_type = "cpu";
 			reg = <1>;
 		};
 
-		cpu@2 {
+		cpu2: cpu@2 {
 			compatible = "arm,cortex-a7";
 			device_type = "cpu";
 			reg = <2>;
 		};
 
-		cpu@3 {
+		cpu3: cpu@3 {
 			compatible = "arm,cortex-a7";
 			device_type = "cpu";
 			reg = <3>;
 		};
 	};
 
+	pmu {
+		compatible = "arm,cortex-a7-pmu";
+		interrupts = <GIC_SPI 120 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_SPI 121 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_SPI 122 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_SPI 123 IRQ_TYPE_LEVEL_HIGH>;
+		interrupt-affinity = <&cpu0>, <&cpu1>, <&cpu2>, <&cpu3>;
+	};
+
 	timer {
 		compatible = "arm,armv7-timer";
 		interrupts = <GIC_PPI 13 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>,
-- 
2.20.1

[PATCH AUTOSEL 4.14 068/186] arm64: dts: qcom: msm8996: Disable USB2 PHY suspend by core

[Sasha Levin]

From: Manu Gautam <mgautam@codeaurora.org>

[ Upstream commit d026c96b25b7ce5df89526aad2df988d553edb4d ]

QUSB2 PHY on msm8996 doesn't work well when autosuspend by
dwc3 core using USB2PHYCFG register is enabled. One of the
issue seen is that PHY driver reports PLL lock failure and
fails phy_init() if dwc3 core has USB2 PHY suspend enabled.
Fix this by using quirks to disable USB2 PHY LPM/suspend and
dwc3 core already takes care of explicitly suspending PHY
during suspend if quirks are specified.

Signed-off-by: Manu Gautam <mgautam@codeaurora.org>
Signed-off-by: Paolo Pisati <p.pisati@gmail.com>
Link: https://lore.kernel.org/r/20191209151501.26993-1-p.pisati@gmail.com
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 arch/arm64/boot/dts/qcom/msm8996.dtsi | 4 ++++
 1 file changed, 4 insertions(+)

diff --git a/arch/arm64/boot/dts/qcom/msm8996.dtsi b/arch/arm64/boot/dts/qcom/msm8996.dtsi
index 6f372ec055dd3..da2949586c7a3 100644
--- a/arch/arm64/boot/dts/qcom/msm8996.dtsi
+++ b/arch/arm64/boot/dts/qcom/msm8996.dtsi
@@ -788,6 +788,8 @@
 				interrupts = <0 138 0>;
 				phys = <&hsusb_phy2>;
 				phy-names = "usb2-phy";
+				snps,dis_u2_susphy_quirk;
+				snps,dis_enblslpm_quirk;
 			};
 		};
 
@@ -817,6 +819,8 @@
 				interrupts = <0 131 0>;
 				phys = <&hsusb_phy1>, <&ssusb_phy_0>;
 				phy-names = "usb2-phy", "usb3-phy";
+				snps,dis_u2_susphy_quirk;
+				snps,dis_enblslpm_quirk;
 			};
 		};
 	};
-- 
2.20.1

[PATCH AUTOSEL 4.14 070/186] ARM: dts: imx6: rdu2: Disable WP for USDHC2 and USDHC3

[Sasha Levin]

From: Andrey Smirnov <andrew.smirnov@gmail.com>

[ Upstream commit cd58a174e58649426fb43d7456e5f7d7eab58af1 ]

RDU2 production units come with resistor connecting WP pin to
correpsonding GPIO DNPed for both SD card slots. Drop any WP related
configuration and mark both slots with "disable-wp".

Reported-by: Chris Healy <cphealy@gmail.com>
Reviewed-by: Chris Healy <cphealy@gmail.com>
Reviewed-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Cc: Shawn Guo <shawnguo@kernel.org>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: Lucas Stach <l.stach@pengutronix.de>
Cc: linux-arm-kernel@lists.infradead.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 arch/arm/boot/dts/imx6qdl-zii-rdu2.dtsi | 6 ++----
 1 file changed, 2 insertions(+), 4 deletions(-)

diff --git a/arch/arm/boot/dts/imx6qdl-zii-rdu2.dtsi b/arch/arm/boot/dts/imx6qdl-zii-rdu2.dtsi
index 849eb3443cde2..719e63092c2ea 100644
--- a/arch/arm/boot/dts/imx6qdl-zii-rdu2.dtsi
+++ b/arch/arm/boot/dts/imx6qdl-zii-rdu2.dtsi
@@ -587,7 +587,7 @@
 	pinctrl-0 = <&pinctrl_usdhc2>;
 	bus-width = <4>;
 	cd-gpios = <&gpio2 2 GPIO_ACTIVE_LOW>;
-	wp-gpios = <&gpio2 3 GPIO_ACTIVE_HIGH>;
+	disable-wp;
 	vmmc-supply = <&reg_3p3v_sd>;
 	vqmmc-supply = <&reg_3p3v>;
 	status = "okay";
@@ -598,7 +598,7 @@
 	pinctrl-0 = <&pinctrl_usdhc3>;
 	bus-width = <4>;
 	cd-gpios = <&gpio2 0 GPIO_ACTIVE_LOW>;
-	wp-gpios = <&gpio2 1 GPIO_ACTIVE_HIGH>;
+	disable-wp;
 	vmmc-supply = <&reg_3p3v_sd>;
 	vqmmc-supply = <&reg_3p3v>;
 	status = "okay";
@@ -1001,7 +1001,6 @@
 			MX6QDL_PAD_SD2_DAT1__SD2_DATA1		0x17059
 			MX6QDL_PAD_SD2_DAT2__SD2_DATA2		0x17059
 			MX6QDL_PAD_SD2_DAT3__SD2_DATA3		0x17059
-			MX6QDL_PAD_NANDF_D3__GPIO2_IO03		0x40010040
 			MX6QDL_PAD_NANDF_D2__GPIO2_IO02		0x40010040
 		>;
 	};
@@ -1014,7 +1013,6 @@
 			MX6QDL_PAD_SD3_DAT1__SD3_DATA1		0x17059
 			MX6QDL_PAD_SD3_DAT2__SD3_DATA2		0x17059
 			MX6QDL_PAD_SD3_DAT3__SD3_DATA3		0x17059
-			MX6QDL_PAD_NANDF_D1__GPIO2_IO01		0x40010040
 			MX6QDL_PAD_NANDF_D0__GPIO2_IO00		0x40010040
 
 		>;
-- 
2.20.1

[PATCH AUTOSEL 4.14 088/186] ARM: dts: r8a7779: Add device node for ARM global timer

[Sasha Levin]

From: Geert Uytterhoeven <geert+renesas@glider.be>

[ Upstream commit 8443ffd1bbd5be74e9b12db234746d12e8ea93e2 ]

Add a device node for the global timer, which is part of the Cortex-A9
MPCore.

The global timer can serve as an accurate (4 ns) clock source for
scheduling and delay loops.

Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20191211135222.26770-4-geert+renesas@glider.be
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 arch/arm/boot/dts/r8a7779.dtsi | 8 ++++++++
 1 file changed, 8 insertions(+)

diff --git a/arch/arm/boot/dts/r8a7779.dtsi b/arch/arm/boot/dts/r8a7779.dtsi
index 8ee0b2ca5d39a..2face089d65b9 100644
--- a/arch/arm/boot/dts/r8a7779.dtsi
+++ b/arch/arm/boot/dts/r8a7779.dtsi
@@ -67,6 +67,14 @@
 		      <0xf0000100 0x100>;
 	};
 
+	timer@f0000200 {
+		compatible = "arm,cortex-a9-global-timer";
+		reg = <0xf0000200 0x100>;
+		interrupts = <GIC_PPI 11
+			(GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_EDGE_RISING)>;
+		clocks = <&cpg_clocks R8A7779_CLK_ZS>;
+	};
+
 	timer@f0000600 {
 		compatible = "arm,cortex-a9-twd-timer";
 		reg = <0xf0000600 0x20>;
-- 
2.20.1

[PATCH AUTOSEL 4.14 111/186] ARM: dts: at91: sama5d3: fix maximum peripheral clock rates

[Sasha Levin]

From: Alexandre Belloni <alexandre.belloni@bootlin.com>

[ Upstream commit ee0aa926ddb0bd8ba59e33e3803b3b5804e3f5da ]

Currently the maximum rate for peripheral clock is calculated based on a
typical 133MHz MCK. The maximum frequency is defined in the datasheet as a
ratio to MCK. Some sama5d3 platforms are using a 166MHz MCK. Update the
device trees to match the maximum rate based on 166MHz.

Reported-by: Karl Rudbæk Olsen <karl@micro-technic.com>
Fixes: d2e8190b7916 ("ARM: at91/dt: define sama5d3 clocks")
Link: https://lore.kernel.org/r/20200110172007.1253659-1-alexandre.belloni@bootlin.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 arch/arm/boot/dts/sama5d3.dtsi      | 28 ++++++++++++++--------------
 arch/arm/boot/dts/sama5d3_can.dtsi  |  4 ++--
 arch/arm/boot/dts/sama5d3_uart.dtsi |  4 ++--
 3 files changed, 18 insertions(+), 18 deletions(-)

diff --git a/arch/arm/boot/dts/sama5d3.dtsi b/arch/arm/boot/dts/sama5d3.dtsi
index 554d0bdedc7a1..f96b41ed5b968 100644
--- a/arch/arm/boot/dts/sama5d3.dtsi
+++ b/arch/arm/boot/dts/sama5d3.dtsi
@@ -1185,49 +1185,49 @@
 					usart0_clk: usart0_clk {
 						#clock-cells = <0>;
 						reg = <12>;
-						atmel,clk-output-range = <0 66000000>;
+						atmel,clk-output-range = <0 83000000>;
 					};
 
 					usart1_clk: usart1_clk {
 						#clock-cells = <0>;
 						reg = <13>;
-						atmel,clk-output-range = <0 66000000>;
+						atmel,clk-output-range = <0 83000000>;
 					};
 
 					usart2_clk: usart2_clk {
 						#clock-cells = <0>;
 						reg = <14>;
-						atmel,clk-output-range = <0 66000000>;
+						atmel,clk-output-range = <0 83000000>;
 					};
 
 					usart3_clk: usart3_clk {
 						#clock-cells = <0>;
 						reg = <15>;
-						atmel,clk-output-range = <0 66000000>;
+						atmel,clk-output-range = <0 83000000>;
 					};
 
 					uart0_clk: uart0_clk {
 						#clock-cells = <0>;
 						reg = <16>;
-						atmel,clk-output-range = <0 66000000>;
+						atmel,clk-output-range = <0 83000000>;
 					};
 
 					twi0_clk: twi0_clk {
 						reg = <18>;
 						#clock-cells = <0>;
-						atmel,clk-output-range = <0 16625000>;
+						atmel,clk-output-range = <0 41500000>;
 					};
 
 					twi1_clk: twi1_clk {
 						#clock-cells = <0>;
 						reg = <19>;
-						atmel,clk-output-range = <0 16625000>;
+						atmel,clk-output-range = <0 41500000>;
 					};
 
 					twi2_clk: twi2_clk {
 						#clock-cells = <0>;
 						reg = <20>;
-						atmel,clk-output-range = <0 16625000>;
+						atmel,clk-output-range = <0 41500000>;
 					};
 
 					mci0_clk: mci0_clk {
@@ -1243,19 +1243,19 @@
 					spi0_clk: spi0_clk {
 						#clock-cells = <0>;
 						reg = <24>;
-						atmel,clk-output-range = <0 133000000>;
+						atmel,clk-output-range = <0 166000000>;
 					};
 
 					spi1_clk: spi1_clk {
 						#clock-cells = <0>;
 						reg = <25>;
-						atmel,clk-output-range = <0 133000000>;
+						atmel,clk-output-range = <0 166000000>;
 					};
 
 					tcb0_clk: tcb0_clk {
 						#clock-cells = <0>;
 						reg = <26>;
-						atmel,clk-output-range = <0 133000000>;
+						atmel,clk-output-range = <0 166000000>;
 					};
 
 					pwm_clk: pwm_clk {
@@ -1266,7 +1266,7 @@
 					adc_clk: adc_clk {
 						#clock-cells = <0>;
 						reg = <29>;
-						atmel,clk-output-range = <0 66000000>;
+						atmel,clk-output-range = <0 83000000>;
 					};
 
 					dma0_clk: dma0_clk {
@@ -1297,13 +1297,13 @@
 					ssc0_clk: ssc0_clk {
 						#clock-cells = <0>;
 						reg = <38>;
-						atmel,clk-output-range = <0 66000000>;
+						atmel,clk-output-range = <0 83000000>;
 					};
 
 					ssc1_clk: ssc1_clk {
 						#clock-cells = <0>;
 						reg = <39>;
-						atmel,clk-output-range = <0 66000000>;
+						atmel,clk-output-range = <0 83000000>;
 					};
 
 					sha_clk: sha_clk {
diff --git a/arch/arm/boot/dts/sama5d3_can.dtsi b/arch/arm/boot/dts/sama5d3_can.dtsi
index c5a3772741bf6..0fac79f75c06c 100644
--- a/arch/arm/boot/dts/sama5d3_can.dtsi
+++ b/arch/arm/boot/dts/sama5d3_can.dtsi
@@ -37,13 +37,13 @@
 					can0_clk: can0_clk {
 						#clock-cells = <0>;
 						reg = <40>;
-						atmel,clk-output-range = <0 66000000>;
+						atmel,clk-output-range = <0 83000000>;
 					};
 
 					can1_clk: can1_clk {
 						#clock-cells = <0>;
 						reg = <41>;
-						atmel,clk-output-range = <0 66000000>;
+						atmel,clk-output-range = <0 83000000>;
 					};
 				};
 			};
diff --git a/arch/arm/boot/dts/sama5d3_uart.dtsi b/arch/arm/boot/dts/sama5d3_uart.dtsi
index 186377d41c917..48e23d18e5e37 100644
--- a/arch/arm/boot/dts/sama5d3_uart.dtsi
+++ b/arch/arm/boot/dts/sama5d3_uart.dtsi
@@ -42,13 +42,13 @@
 					uart0_clk: uart0_clk {
 						#clock-cells = <0>;
 						reg = <16>;
-						atmel,clk-output-range = <0 66000000>;
+						atmel,clk-output-range = <0 83000000>;
 					};
 
 					uart1_clk: uart1_clk {
 						#clock-cells = <0>;
 						reg = <17>;
-						atmel,clk-output-range = <0 66000000>;
+						atmel,clk-output-range = <0 83000000>;
 					};
 				};
 			};
-- 
2.20.1

[PATCH AUTOSEL 4.14 112/186] ARM: dts: at91: sama5d3: define clock rate range for tcb1

[Sasha Levin]

From: Alexandre Belloni <alexandre.belloni@bootlin.com>

[ Upstream commit a7e0f3fc01df4b1b7077df777c37feae8c9e8b6d ]

The clock rate range for the TCB1 clock is missing. define it in the device
tree.

Reported-by: Karl Rudbæk Olsen <karl@micro-technic.com>
Fixes: d2e8190b7916 ("ARM: at91/dt: define sama5d3 clocks")
Link: https://lore.kernel.org/r/20200110172007.1253659-2-alexandre.belloni@bootlin.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 arch/arm/boot/dts/sama5d3_tcb1.dtsi | 1 +
 1 file changed, 1 insertion(+)

diff --git a/arch/arm/boot/dts/sama5d3_tcb1.dtsi b/arch/arm/boot/dts/sama5d3_tcb1.dtsi
index 801f9745e82f1..b80dbc45a3c20 100644
--- a/arch/arm/boot/dts/sama5d3_tcb1.dtsi
+++ b/arch/arm/boot/dts/sama5d3_tcb1.dtsi
@@ -23,6 +23,7 @@
 					tcb1_clk: tcb1_clk {
 						#clock-cells = <0>;
 						reg = <27>;
+						atmel,clk-output-range = <0 166000000>;
 					};
 				};
 			};
-- 
2.20.1

[PATCH AUTOSEL 4.14 123/186] ARC: [plat-axs10x]: Add missing multicast filter number to GMAC node

[Sasha Levin]

From: Jose Abreu <Jose.Abreu@synopsys.com>

[ Upstream commit 7980dff398f86a618f502378fa27cf7e77449afa ]

Add a missing property to GMAC node so that multicast filtering works
correctly.

Fixes: 556cc1c5f528 ("ARC: [axs101] Add support for AXS101 SDP (software development platform)")
Acked-by: Alexey Brodkin <abrodkin@synopsys.com>
Signed-off-by: Jose Abreu <Jose.Abreu@synopsys.com>
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 arch/arc/boot/dts/axs10x_mb.dtsi | 1 +
 1 file changed, 1 insertion(+)

diff --git a/arch/arc/boot/dts/axs10x_mb.dtsi b/arch/arc/boot/dts/axs10x_mb.dtsi
index e114000a84f56..d825b9dbae5de 100644
--- a/arch/arc/boot/dts/axs10x_mb.dtsi
+++ b/arch/arc/boot/dts/axs10x_mb.dtsi
@@ -70,6 +70,7 @@
 			interrupt-names = "macirq";
 			phy-mode = "rgmii";
 			snps,pbl = < 32 >;
+			snps,multicast-filter-bins = <256>;
 			clocks = <&apbclk>;
 			clock-names = "stmmaceth";
 			max-speed = <100>;
-- 
2.20.1