[PATCH v2 7/9] dt-bindings: PCI: aardvark: describe new properties

[PATCH v2 7/9] dt-bindings: PCI: aardvark: describe new properties

[Marek Behún]

Document the possibility to reference a PHY and reset-gpios and to set
max-link-speed property.

Signed-off-by: Marek Behún <marek.behun@nic.cz>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: devicetree@vger.kernel.org
---
 Documentation/devicetree/bindings/pci/aardvark-pci.txt | 4 ++++
 1 file changed, 4 insertions(+)

diff --git a/Documentation/devicetree/bindings/pci/aardvark-pci.txt b/Documentation/devicetree/bindings/pci/aardvark-pci.txt
index 310ef7145c47..2b8ca920a7fa 100644
--- a/Documentation/devicetree/bindings/pci/aardvark-pci.txt
+++ b/Documentation/devicetree/bindings/pci/aardvark-pci.txt
@@ -19,6 +19,9 @@ contain the following properties:
  - interrupt-map-mask and interrupt-map: standard PCI properties to
    define the mapping of the PCIe interface to interrupt numbers.
  - bus-range: PCI bus numbers covered
+ - phys: the PCIe PHY handle
+ - max-link-speed: see pci.txt
+ - reset-gpios: see pci.txt
 
 In addition, the Device Tree describing an Aardvark PCIe controller
 must include a sub-node that describes the legacy interrupt controller
@@ -48,6 +51,7 @@ Example:
 				<0 0 0 2 &pcie_intc 1>,
 				<0 0 0 3 &pcie_intc 2>,
 				<0 0 0 4 &pcie_intc 3>;
+		phys = <&comphy1 0>;
 		pcie_intc: interrupt-controller {
 			interrupt-controller;
 			#interrupt-cells = <1>;
-- 
2.24.1

[PATCH v2 8/9] arm64: dts: marvell: armada-37xx: set pcie_reset_pin to gpio function

[Marek Behún]

We found out that we are unable to control the PERST# signal via the
default pin dedicated to be PERST# pin (GPIO2[3] pin) on A3700 SOC when
this pin is in EP_PCIE1_Resetn mode. There is a register in the PCIe
register space called PERSTN_GPIO_EN (D0088004[3]), but changing the
value of this register does not change the pin output when measuring
with voltmeter.

We do not know if this is a bug in the SOC, or if it works only when
PCIe controller is in a certain state.

Commit f4c7d053d7f7 ("PCI: aardvark: Wait for endpoint to be ready
before training link") says that when this pin changes pinctrl mode
from EP_PCIE1_Resetn to GPIO, the PERST# signal is asserted for a brief
moment.

So currently the situation is that on A3700 boards the PERST# signal is
asserted in U-Boot (because the code in U-Boot issues reset via this pin
via GPIO mode), and then in Linux by the obscure and undocumented
mechanism described by the above mentioned commit.

We want to issue PERST# signal in a known way, therefore this patch
changes the pcie_reset_pin function from "pcie" to "gpio" and adds the
reset-gpios property to the PCIe node in device tree files of
EspressoBin and Armada 3720 Dev Board (Turris Mox device tree already
has this property and uDPU does not have a PCIe port).

Signed-off-by: Marek Behún <marek.behun@nic.cz>
Cc: Remi Pommarel <repk@triplefau.lt>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: devicetree@vger.kernel.org
---
 arch/arm64/boot/dts/marvell/armada-3720-db.dts           | 3 +++
 arch/arm64/boot/dts/marvell/armada-3720-espressobin.dtsi | 1 +
 arch/arm64/boot/dts/marvell/armada-3720-turris-mox.dts   | 4 ----
 arch/arm64/boot/dts/marvell/armada-37xx.dtsi             | 2 +-
 4 files changed, 5 insertions(+), 5 deletions(-)

diff --git a/arch/arm64/boot/dts/marvell/armada-3720-db.dts b/arch/arm64/boot/dts/marvell/armada-3720-db.dts
index f2cc00594d64..3e5789f37206 100644
--- a/arch/arm64/boot/dts/marvell/armada-3720-db.dts
+++ b/arch/arm64/boot/dts/marvell/armada-3720-db.dts
@@ -128,6 +128,9 @@ phy1: ethernet-phy@1 {
 
 /* CON15(V2.0)/CON17(V1.4) : PCIe / CON15(V2.0)/CON12(V1.4) :mini-PCIe */
 &pcie0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pcie_reset_pins &pcie_clkreq_pins>;
+	reset-gpios = <&gpiosb 3 GPIO_ACTIVE_LOW>;
 	status = "okay";
 };
 
diff --git a/arch/arm64/boot/dts/marvell/armada-3720-espressobin.dtsi b/arch/arm64/boot/dts/marvell/armada-3720-espressobin.dtsi
index 42e992f9c8a5..c92ad664cb0e 100644
--- a/arch/arm64/boot/dts/marvell/armada-3720-espressobin.dtsi
+++ b/arch/arm64/boot/dts/marvell/armada-3720-espressobin.dtsi
@@ -47,6 +47,7 @@ &pcie0 {
 	phys = <&comphy1 0>;
 	pinctrl-names = "default";
 	pinctrl-0 = <&pcie_reset_pins &pcie_clkreq_pins>;
+	reset-gpios = <&gpiosb 3 GPIO_ACTIVE_LOW>;
 };
 
 /* J6 */
diff --git a/arch/arm64/boot/dts/marvell/armada-3720-turris-mox.dts b/arch/arm64/boot/dts/marvell/armada-3720-turris-mox.dts
index bb42d1e6a4e9..e496bd9d4737 100644
--- a/arch/arm64/boot/dts/marvell/armada-3720-turris-mox.dts
+++ b/arch/arm64/boot/dts/marvell/armada-3720-turris-mox.dts
@@ -128,10 +128,6 @@ rtc@6f {
 	};
 };
 
-&pcie_reset_pins {
-	function = "gpio";
-};
-
 &pcie0 {
 	pinctrl-names = "default";
 	pinctrl-0 = <&pcie_reset_pins &pcie_clkreq_pins>;
diff --git a/arch/arm64/boot/dts/marvell/armada-37xx.dtsi b/arch/arm64/boot/dts/marvell/armada-37xx.dtsi
index 000c135e39b7..7909c146eabf 100644
--- a/arch/arm64/boot/dts/marvell/armada-37xx.dtsi
+++ b/arch/arm64/boot/dts/marvell/armada-37xx.dtsi
@@ -317,7 +317,7 @@ sdio_pins: sdio-pins {
 
 				pcie_reset_pins: pcie-reset-pins {
 					groups = "pcie1";
-					function = "pcie";
+					function = "gpio";
 				};
 
 				pcie_clkreq_pins: pcie-clkreq-pins {
-- 
2.24.1

[PATCH v2 9/9] arm64: dts: marvell: armada-37xx: move PCIe comphy handle property

[Marek Behún]

Move the comphy handle property of the PCIe node from board specific
device tree files (EspressoBin and Turris Mox) to the generic
armada-37xx.dtsi.

This is correct since this is the only possible PCIe PHY configuration
on Armada 37xx, so when PCIe is enabled on any board, this handle is
correct.

Signed-off-by: Marek Behún <marek.behun@nic.cz>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: devicetree@vger.kernel.org
---
 arch/arm64/boot/dts/marvell/armada-3720-espressobin.dtsi | 1 -
 arch/arm64/boot/dts/marvell/armada-3720-turris-mox.dts   | 1 -
 arch/arm64/boot/dts/marvell/armada-37xx.dtsi             | 1 +
 3 files changed, 1 insertion(+), 2 deletions(-)

diff --git a/arch/arm64/boot/dts/marvell/armada-3720-espressobin.dtsi b/arch/arm64/boot/dts/marvell/armada-3720-espressobin.dtsi
index c92ad664cb0e..b97218c72727 100644
--- a/arch/arm64/boot/dts/marvell/armada-3720-espressobin.dtsi
+++ b/arch/arm64/boot/dts/marvell/armada-3720-espressobin.dtsi
@@ -44,7 +44,6 @@ vcc_sd_reg1: regulator {
 /* J9 */
 &pcie0 {
 	status = "okay";
-	phys = <&comphy1 0>;
 	pinctrl-names = "default";
 	pinctrl-0 = <&pcie_reset_pins &pcie_clkreq_pins>;
 	reset-gpios = <&gpiosb 3 GPIO_ACTIVE_LOW>;
diff --git a/arch/arm64/boot/dts/marvell/armada-3720-turris-mox.dts b/arch/arm64/boot/dts/marvell/armada-3720-turris-mox.dts
index e496bd9d4737..15c1cf5c5b69 100644
--- a/arch/arm64/boot/dts/marvell/armada-3720-turris-mox.dts
+++ b/arch/arm64/boot/dts/marvell/armada-3720-turris-mox.dts
@@ -134,7 +134,6 @@ &pcie0 {
 	status = "okay";
 	max-link-speed = <2>;
 	reset-gpios = <&gpiosb 3 GPIO_ACTIVE_LOW>;
-	phys = <&comphy1 0>;
 
 	/* enabled by U-Boot if PCIe module is present */
 	status = "disabled";
diff --git a/arch/arm64/boot/dts/marvell/armada-37xx.dtsi b/arch/arm64/boot/dts/marvell/armada-37xx.dtsi
index 7909c146eabf..5aaad64a793d 100644
--- a/arch/arm64/boot/dts/marvell/armada-37xx.dtsi
+++ b/arch/arm64/boot/dts/marvell/armada-37xx.dtsi
@@ -493,6 +493,7 @@ pcie0: pcie@d0070000 {
 					<0 0 0 2 &pcie_intc 1>,
 					<0 0 0 3 &pcie_intc 2>,
 					<0 0 0 4 &pcie_intc 3>;
+			phys = <&comphy1 0>;
 			pcie_intc: interrupt-controller {
 				interrupt-controller;
 				#interrupt-cells = <1>;
-- 
2.24.1

Re: [PATCH v2 7/9] dt-bindings: PCI: aardvark: describe new properties

[Rob Herring]

On Tue, 21 Apr 2020 13:16:59 +0200, Marek Behún wrote:
> Document the possibility to reference a PHY and reset-gpios and to set
> max-link-speed property.
> 
> Signed-off-by: Marek Behún <marek.behun@nic.cz>
> Cc: Rob Herring <robh+dt@kernel.org>
> Cc: devicetree@vger.kernel.org
> ---
>  Documentation/devicetree/bindings/pci/aardvark-pci.txt | 4 ++++
>  1 file changed, 4 insertions(+)
> 

Reviewed-by: Rob Herring <robh@kernel.org>