[PATCH v6 1/3] dt-bindings: vendor-prefixes: add Seeed Studio

[PATCH v6 1/3] dt-bindings: vendor-prefixes: add Seeed Studio

[Marcin Sloniewski]

Add the "seeed" vendor prefix for Seeed Technology Co., Ltd
Website: https://www.seeedstudio.com/

Signed-off-by: Marcin Sloniewski <marcin.sloniewski@gmail.com>
Acked-by: Rob Herring <robh@kernel.org>
---
 Documentation/devicetree/bindings/vendor-prefixes.yaml | 2 ++
 1 file changed, 2 insertions(+)

diff --git a/Documentation/devicetree/bindings/vendor-prefixes.yaml b/Documentation/devicetree/bindings/vendor-prefixes.yaml
index 9aeab66be85f..7dd03b3e9d3c 100644
--- a/Documentation/devicetree/bindings/vendor-prefixes.yaml
+++ b/Documentation/devicetree/bindings/vendor-prefixes.yaml
@@ -902,6 +902,8 @@ patternProperties:
     description: Schindler
   "^seagate,.*":
     description: Seagate Technology PLC
+  "^seeed,.*":
+    description: Seeed Technology Co., Ltd
   "^seirobotics,.*":
     description: Shenzhen SEI Robotics Co., Ltd
   "^semtech,.*":
-- 
2.27.0

[PATCH v6 2/3] dt-bindings: arm: stm32: document Odyssey compatible

[Marcin Sloniewski]

Document device tree bindings of Seeed SoM and carrier board.

Signed-off-by: Marcin Sloniewski <marcin.sloniewski@gmail.com>
---
 Documentation/devicetree/bindings/arm/stm32/stm32.yaml | 6 ++++++
 1 file changed, 6 insertions(+)

diff --git a/Documentation/devicetree/bindings/arm/stm32/stm32.yaml b/Documentation/devicetree/bindings/arm/stm32/stm32.yaml
index 790e6dd48e34..3b318fe15194 100644
--- a/Documentation/devicetree/bindings/arm/stm32/stm32.yaml
+++ b/Documentation/devicetree/bindings/arm/stm32/stm32.yaml
@@ -50,4 +50,10 @@ properties:
           - const: st,stm32mp157c-ev1
           - const: st,stm32mp157c-ed1
           - const: st,stm32mp157
+      - description: Odyssey STM32MP1 SoM based Boards
+        items:
+              - enum:
+                  - seeed,stm32mp157c-odyssey
+              - const: seeed,stm32mp157c-odyssey-som
+              - const: st,stm32mp157
 ...
-- 
2.27.0

[PATCH v6 3/3] ARM: dts: stm32: add initial support for stm32mp157-odyssey board

[Marcin Sloniewski]

Add support for Seeed Studio's stm32mp157c odyssey board.
Board consists of SoM with stm32mp157c with 4GB eMMC and 512 MB DDR3 RAM
and carrier board with USB and ETH interfaces, SD card connector,
wifi and BT chip AP6236.

In this patch only basic kernel boot is supported and interfacing
SD card and on-board eMMC.

Signed-off-by: Marcin Sloniewski <marcin.sloniewski@gmail.com>
---

Changes in v6:
- add reset pin for eth phy
- move pinctrl for sdmmc2 to stm32mp15-pinctrl.dtsi

Changes in v5:
- fix schema for board's dts

Changes in v4:
- add seeed,stm32mp157c-odyssey-som in compatible
  for carrier board
- fix sdmmc2 interface by changing one of the pins
  to use
- change eth phy address to 7

Changes in v3:
- fix compilation on tip of stm32-next
  due to change in names for pinctrl
- fix deprecated binding for led node
- fix redundant "okay" statuses
- add phy part number for eth in comment

Changes in v2:
- add new odyssey dts to Makefile


 arch/arm/boot/dts/Makefile                    |   3 +-
 arch/arm/boot/dts/stm32mp15-pinctrl.dtsi      |  18 ++
 .../arm/boot/dts/stm32mp157c-odyssey-som.dtsi | 276 ++++++++++++++++++
 arch/arm/boot/dts/stm32mp157c-odyssey.dts     |  76 +++++
 4 files changed, 372 insertions(+), 1 deletion(-)
 create mode 100644 arch/arm/boot/dts/stm32mp157c-odyssey-som.dtsi
 create mode 100644 arch/arm/boot/dts/stm32mp157c-odyssey.dts

diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
index e6a1cac0bfc7..a3ea2301c82c 100644
--- a/arch/arm/boot/dts/Makefile
+++ b/arch/arm/boot/dts/Makefile
@@ -1047,7 +1047,8 @@ dtb-$(CONFIG_ARCH_STM32) += \
 	stm32mp157c-dk2.dtb \
 	stm32mp157c-ed1.dtb \
 	stm32mp157c-ev1.dtb \
-	stm32mp157c-lxa-mc1.dtb
+	stm32mp157c-lxa-mc1.dtb \
+	stm32mp157c-odyssey.dtb
 dtb-$(CONFIG_MACH_SUN4I) += \
 	sun4i-a10-a1000.dtb \
 	sun4i-a10-ba10-tvbox.dtb \
diff --git a/arch/arm/boot/dts/stm32mp15-pinctrl.dtsi b/arch/arm/boot/dts/stm32mp15-pinctrl.dtsi
index b5a66429670c..a47eaecbde42 100644
--- a/arch/arm/boot/dts/stm32mp15-pinctrl.dtsi
+++ b/arch/arm/boot/dts/stm32mp15-pinctrl.dtsi
@@ -1437,6 +1437,24 @@ pins {
 		};
 	};
 
+	sdmmc2_d47_pins_d: sdmmc2-d47-3 {
+		pins {
+			pinmux = <STM32_PINMUX('A', 8, AF9)>, /* SDMMC2_D4 */
+				 <STM32_PINMUX('A', 9, AF10)>, /* SDMMC2_D5 */
+				 <STM32_PINMUX('E', 5, AF9)>, /* SDMMC2_D6 */
+				 <STM32_PINMUX('C', 7, AF10)>; /* SDMMC2_D7 */
+		};
+	};
+
+	sdmmc2_d47_sleep_pins_d: sdmmc2-d47-sleep-3 {
+		pins {
+			pinmux = <STM32_PINMUX('A', 8, ANALOG)>, /* SDMMC2_D4 */
+				 <STM32_PINMUX('A', 9, ANALOG)>, /* SDMMC2_D5 */
+				 <STM32_PINMUX('E', 5, ANALOG)>, /* SDMMC2_D6 */
+				 <STM32_PINMUX('C', 7, ANALOG)>; /* SDMMC2_D7 */
+		};
+	};
+
 	sdmmc3_b4_pins_a: sdmmc3-b4-0 {
 		pins1 {
 			pinmux = <STM32_PINMUX('F', 0, AF9)>, /* SDMMC3_D0 */
diff --git a/arch/arm/boot/dts/stm32mp157c-odyssey-som.dtsi b/arch/arm/boot/dts/stm32mp157c-odyssey-som.dtsi
new file mode 100644
index 000000000000..6cf49a0a9e69
--- /dev/null
+++ b/arch/arm/boot/dts/stm32mp157c-odyssey-som.dtsi
@@ -0,0 +1,276 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR BSD-3-Clause)
+/*
+ * Copyright (C) 2020 Marcin Sloniewski <marcin.sloniewski@gmail.com>.
+ */
+
+/dts-v1/;
+
+#include "stm32mp157.dtsi"
+#include "stm32mp15xc.dtsi"
+#include "stm32mp15-pinctrl.dtsi"
+#include "stm32mp15xxac-pinctrl.dtsi"
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/leds/common.h>
+#include <dt-bindings/mfd/st,stpmic1.h>
+
+/ {
+	model = "Seeed Studio Odyssey-STM32MP157C SOM";
+	compatible = "seeed,stm32mp157c-odyssey-som", "st,stm32mp157";
+
+	memory@c0000000 {
+		device_type = "memory";
+		reg = <0xc0000000 0x20000000>;
+	};
+
+	reserved-memory {
+		#address-cells = <1>;
+		#size-cells = <1>;
+		ranges;
+
+		mcuram2: mcuram2@10000000 {
+			compatible = "shared-dma-pool";
+			reg = <0x10000000 0x40000>;
+			no-map;
+		};
+
+		vdev0vring0: vdev0vring0@10040000 {
+			compatible = "shared-dma-pool";
+			reg = <0x10040000 0x1000>;
+			no-map;
+		};
+
+		vdev0vring1: vdev0vring1@10041000 {
+			compatible = "shared-dma-pool";
+			reg = <0x10041000 0x1000>;
+			no-map;
+		};
+
+		vdev0buffer: vdev0buffer@10042000 {
+			compatible = "shared-dma-pool";
+			reg = <0x10042000 0x4000>;
+			no-map;
+		};
+
+		mcuram: mcuram@30000000 {
+			compatible = "shared-dma-pool";
+			reg = <0x30000000 0x40000>;
+			no-map;
+		};
+
+		retram: retram@38000000 {
+			compatible = "shared-dma-pool";
+			reg = <0x38000000 0x10000>;
+			no-map;
+		};
+
+		gpu_reserved: gpu@d4000000 {
+			reg = <0xd4000000 0x4000000>;
+			no-map;
+		};
+	};
+
+	led {
+		compatible = "gpio-leds";
+		led-blue {
+			color = <LED_COLOR_ID_BLUE>;
+			function = LED_FUNCTION_HEARTBEAT;
+			gpios = <&gpiog 3 GPIO_ACTIVE_HIGH>;
+			linux,default-trigger = "heartbeat";
+		};
+	};
+};
+
+&gpu {
+	contiguous-area = <&gpu_reserved>;
+	status = "okay";
+};
+
+&i2c2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&i2c2_pins_a>;
+	i2c-scl-rising-time-ns = <185>;
+	i2c-scl-falling-time-ns = <20>;
+	status = "okay";
+	/* spare dmas for other usage */
+	/delete-property/dmas;
+	/delete-property/dma-names;
+
+	pmic: stpmic@33 {
+		compatible = "st,stpmic1";
+		reg = <0x33>;
+		interrupts-extended = <&gpioa 0 IRQ_TYPE_EDGE_FALLING>;
+		interrupt-controller;
+		#interrupt-cells = <2>;
+
+		regulators {
+			compatible = "st,stpmic1-regulators";
+			ldo1-supply = <&v3v3>;
+			ldo3-supply = <&vdd_ddr>;
+			ldo6-supply = <&v3v3>;
+			pwr_sw1-supply = <&bst_out>;
+			pwr_sw2-supply = <&bst_out>;
+
+			vddcore: buck1 {
+				regulator-name = "vddcore";
+				regulator-min-microvolt = <800000>;
+				regulator-max-microvolt = <1350000>;
+				regulator-always-on;
+				regulator-initial-mode = <0>;
+				regulator-over-current-protection;
+			};
+
+			vdd_ddr: buck2 {
+				regulator-name = "vdd_ddr";
+				regulator-min-microvolt = <1350000>;
+				regulator-max-microvolt = <1350000>;
+				regulator-always-on;
+				regulator-initial-mode = <0>;
+				regulator-over-current-protection;
+			};
+
+			vdd: buck3 {
+				regulator-name = "vdd";
+				regulator-min-microvolt = <3300000>;
+				regulator-max-microvolt = <3300000>;
+				regulator-always-on;
+				st,mask-reset;
+				regulator-initial-mode = <0>;
+				regulator-over-current-protection;
+			};
+
+			v3v3: buck4 {
+				regulator-name = "v3v3";
+				regulator-min-microvolt = <3300000>;
+				regulator-max-microvolt = <3300000>;
+				regulator-always-on;
+				regulator-over-current-protection;
+				regulator-initial-mode = <0>;
+			};
+
+			v1v8_audio: ldo1 {
+				regulator-name = "v1v8_audio";
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <1800000>;
+				regulator-always-on;
+				interrupts = <IT_CURLIM_LDO1 0>;
+			};
+
+			v3v3_hdmi: ldo2 {
+				regulator-name = "v3v3_hdmi";
+				regulator-min-microvolt = <3300000>;
+				regulator-max-microvolt = <3300000>;
+				regulator-always-on;
+				interrupts = <IT_CURLIM_LDO2 0>;
+			};
+
+			vtt_ddr: ldo3 {
+				regulator-name = "vtt_ddr";
+				regulator-min-microvolt = <500000>;
+				regulator-max-microvolt = <750000>;
+				regulator-always-on;
+				regulator-over-current-protection;
+			};
+
+			vdd_usb: ldo4 {
+				regulator-name = "vdd_usb";
+				regulator-min-microvolt = <3300000>;
+				regulator-max-microvolt = <3300000>;
+				interrupts = <IT_CURLIM_LDO4 0>;
+			};
+
+			vdda: ldo5 {
+				regulator-name = "vdda";
+				regulator-min-microvolt = <2900000>;
+				regulator-max-microvolt = <2900000>;
+				interrupts = <IT_CURLIM_LDO5 0>;
+				regulator-boot-on;
+			};
+
+			v1v2_hdmi: ldo6 {
+				regulator-name = "v1v2_hdmi";
+				regulator-min-microvolt = <1200000>;
+				regulator-max-microvolt = <1200000>;
+				regulator-always-on;
+				interrupts = <IT_CURLIM_LDO6 0>;
+			};
+
+			vref_ddr: vref_ddr {
+				regulator-name = "vref_ddr";
+				regulator-always-on;
+				regulator-over-current-protection;
+			};
+
+			 bst_out: boost {
+				regulator-name = "bst_out";
+				interrupts = <IT_OCP_BOOST 0>;
+			 };
+
+			vbus_otg: pwr_sw1 {
+				regulator-name = "vbus_otg";
+				interrupts = <IT_OCP_OTG 0>;
+			 };
+
+			 vbus_sw: pwr_sw2 {
+				regulator-name = "vbus_sw";
+				interrupts = <IT_OCP_SWOUT 0>;
+				regulator-active-discharge;
+			 };
+		};
+
+		onkey {
+			compatible = "st,stpmic1-onkey";
+			interrupts = <IT_PONKEY_F 0>, <IT_PONKEY_R 0>;
+			interrupt-names = "onkey-falling", "onkey-rising";
+			power-off-time-sec = <10>;
+		};
+
+		watchdog {
+			compatible = "st,stpmic1-wdt";
+			status = "disabled";
+		};
+	};
+};
+
+&ipcc {
+	status = "okay";
+};
+
+&iwdg2 {
+	timeout-sec = <32>;
+	status = "okay";
+};
+
+&m4_rproc {
+	memory-region = <&retram>, <&mcuram>, <&mcuram2>, <&vdev0vring0>,
+			<&vdev0vring1>, <&vdev0buffer>;
+	mboxes = <&ipcc 0>, <&ipcc 1>, <&ipcc 2>;
+	mbox-names = "vq0", "vq1", "shutdown";
+	interrupt-parent = <&exti>;
+	interrupts = <68 1>;
+	status = "okay";
+};
+
+&rng1 {
+	status = "okay";
+};
+
+&rtc {
+	status = "okay";
+};
+
+&sdmmc2 {
+	pinctrl-names = "default", "opendrain", "sleep";
+	pinctrl-0 = <&sdmmc2_b4_pins_a &sdmmc2_d47_pins_d>;
+	pinctrl-1 = <&sdmmc2_b4_od_pins_a &sdmmc2_d47_pins_d>;
+	pinctrl-2 = <&sdmmc2_b4_sleep_pins_a &sdmmc2_d47_sleep_pins_d>;
+	non-removable;
+	no-sd;
+	no-sdio;
+	st,neg-edge;
+	bus-width = <8>;
+	vmmc-supply = <&v3v3>;
+	vqmmc-supply = <&v3v3>;
+	mmc-ddr-3_3v;
+	status = "okay";
+};
+
diff --git a/arch/arm/boot/dts/stm32mp157c-odyssey.dts b/arch/arm/boot/dts/stm32mp157c-odyssey.dts
new file mode 100644
index 000000000000..f2ac92f1ad10
--- /dev/null
+++ b/arch/arm/boot/dts/stm32mp157c-odyssey.dts
@@ -0,0 +1,76 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR BSD-3-Clause)
+/*
+ * Copyright (C) 2020 Marcin Sloniewski <marcin.sloniewski@gmail.com>.
+ */
+
+/dts-v1/;
+
+#include "stm32mp157c-odyssey-som.dtsi"
+
+/ {
+	model = "Seeed Studio Odyssey-STM32MP157C Board";
+	compatible = "seeed,stm32mp157c-odyssey",
+		     "seeed,stm32mp157c-odyssey-som", "st,stm32mp157";
+
+	aliases {
+		ethernet0 = &ethernet0;
+		serial0 = &uart4;
+	};
+
+	chosen {
+		stdout-path = "serial0:115200n8";
+	};
+};
+
+&ethernet0 {
+	status = "okay";
+	pinctrl-0 = <&ethernet0_rgmii_pins_a>;
+	pinctrl-1 = <&ethernet0_rgmii_sleep_pins_a>;
+	pinctrl-names = "default", "sleep";
+	phy-mode = "rgmii-id";
+	max-speed = <1000>;
+	phy-handle = <&phy0>;
+
+	mdio0 {
+		#address-cells = <1>;
+		#size-cells = <0>;
+		compatible = "snps,dwmac-mdio";
+		phy0: ethernet-phy@7 { /* KSZ9031RN */
+			reg = <7>;
+			reset-gpios = <&gpiog 0 GPIO_ACTIVE_LOW>; /* ETH_RST# */
+			reset-assert-us = <10000>;
+			reset-deassert-us = <300>;
+		};
+	};
+};
+
+&i2c1 {
+	pinctrl-names = "default", "sleep";
+	pinctrl-0 = <&i2c1_pins_a>;
+	pinctrl-1 = <&i2c1_sleep_pins_a>;
+	i2c-scl-rising-time-ns = <100>;
+	i2c-scl-falling-time-ns = <7>;
+	status = "okay";
+	/delete-property/dmas;
+	/delete-property/dma-names;
+};
+
+&sdmmc1 {
+	pinctrl-names = "default", "opendrain", "sleep";
+	pinctrl-0 = <&sdmmc1_b4_pins_a>;
+	pinctrl-1 = <&sdmmc1_b4_od_pins_a>;
+	pinctrl-2 = <&sdmmc1_b4_sleep_pins_a>;
+	cd-gpios = <&gpiob 7 (GPIO_ACTIVE_LOW | GPIO_PULL_UP)>;
+	disable-wp;
+	st,neg-edge;
+	bus-width = <4>;
+	vmmc-supply = <&v3v3>;
+	status = "okay";
+};
+
+&uart4 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&uart4_pins_a>;
+	status = "okay";
+};
+
-- 
2.27.0

Re: [PATCH v6 2/3] dt-bindings: arm: stm32: document Odyssey compatible

[Rob Herring]

On Fri, 31 Jul 2020 16:30:52 +0200, Marcin Sloniewski wrote:
> Document device tree bindings of Seeed SoM and carrier board.
> 
> Signed-off-by: Marcin Sloniewski <marcin.sloniewski@gmail.com>
> ---
>  Documentation/devicetree/bindings/arm/stm32/stm32.yaml | 6 ++++++
>  1 file changed, 6 insertions(+)
> 


Please add Acked-by/Reviewed-by tags when posting new versions. However,
there's no need to repost patches *only* to add the tags. The upstream
maintainer will do that for acks received on the version they apply.

If a tag was not added on purpose, please state why and what changed.