* [RFC v4 0/3] Re-introduce TX FIFO resize for larger EP bursting @ 2020-06-24 2:28 Wesley Cheng 2020-06-24 2:28 ` [RFC v4 1/3] usb: dwc3: Resize TX FIFOs to meet EP bursting requirements Wesley Cheng ` (2 more replies) 0 siblings, 3 replies; 13+ messages in thread From: Wesley Cheng @ 2020-06-24 2:28 UTC (permalink / raw) To: agross, bjorn.andersson, balbi, gregkh, robh+dt Cc: linux-kernel, devicetree, linux-arm-msm, linux-usb, jackp, Wesley Cheng Changes in V4: - Removed struct dwc3* as an argument for dwc3_gadget_resize_tx_fifos() - Removed WARN_ON(1) in case we run out of fifo space Changes in V3: - Removed "Reviewed-by" tags - Renamed series back to RFC - Modified logic to ensure that fifo_size is reset if we pass the minimum threshold. Tested with binding multiple FDs requesting 6 FIFOs. Changes in V2: - Modified TXFIFO resizing logic to ensure that each EP is reserved a FIFO. - Removed dev_dbg() prints and fixed typos from patches - Added some more description on the dt-bindings commit message Currently, there is no functionality to allow for resizing the TXFIFOs, and relying on the HW default setting for the TXFIFO depth. In most cases, the HW default is probably sufficient, but for USB compositions that contain multiple functions that require EP bursting, the default settings might not be enough. Also to note, the current SW will assign an EP to a function driver w/o checking to see if the TXFIFO size for that particular EP is large enough. (this is a problem if there are multiple HW defined values for the TXFIFO size) It is mentioned in the SNPS databook that a minimum of TX FIFO depth = 3 is required for an EP that supports bursting. Otherwise, there may be frequent occurences of bursts ending. For high bandwidth functions, such as data tethering (protocols that support data aggregation), mass storage, and media transfer protocol (over FFS), the bMaxBurst value can be large, and a bigger TXFIFO depth may prove to be beneficial in terms of USB throughput. (which can be associated to system access latency, etc...) It allows for a more consistent burst of traffic, w/o any interruptions, as data is readily available in the FIFO. With testing done using the mass storage function driver, the results show that with a larger TXFIFO depth, the bandwidth increased significantly. Test Parameters: - Platform: Qualcomm SM8150 - bMaxBurst = 6 - USB req size = 256kB - Num of USB reqs = 16 - USB Speed = Super-Speed - Function Driver: Mass Storage (w/ ramdisk) - Test Application: CrystalDiskMark Results: TXFIFO Depth = 3 max packets Test Case | Data Size | AVG tput (in MB/s) ------------------------------------------- Sequential|1 GB x | Read |9 loops | 193.60 | | 195.86 | | 184.77 | | 193.60 ------------------------------------------- TXFIFO Depth = 6 max packets Test Case | Data Size | AVG tput (in MB/s) ------------------------------------------- Sequential|1 GB x | Read |9 loops | 287.35 | | 304.94 | | 289.64 | | 293.61 ------------------------------------------- Wesley Cheng (3): usb: dwc3: Resize TX FIFOs to meet EP bursting requirements arm64: boot: dts: qcom: sm8150: Enable dynamic TX FIFO resize logic dt-bindings: usb: dwc3: Add entry for tx-fifo-resize .../devicetree/bindings/usb/dwc3.txt | 2 +- arch/arm64/boot/dts/qcom/sm8150.dtsi | 1 + drivers/usb/dwc3/core.c | 2 + drivers/usb/dwc3/core.h | 8 ++ drivers/usb/dwc3/ep0.c | 37 +++++- drivers/usb/dwc3/gadget.c | 115 ++++++++++++++++++ 6 files changed, 163 insertions(+), 2 deletions(-) -- The Qualcomm Innovation Center, Inc. is a member of the Code Aurora Forum, a Linux Foundation Collaborative Project ^ permalink raw reply [flat|nested] 13+ messages in thread
* [RFC v4 1/3] usb: dwc3: Resize TX FIFOs to meet EP bursting requirements 2020-06-24 2:28 [RFC v4 0/3] Re-introduce TX FIFO resize for larger EP bursting Wesley Cheng @ 2020-06-24 2:28 ` Wesley Cheng 2020-08-10 12:27 ` Felipe Balbi 2020-08-12 2:22 ` Peter Chen 2020-06-24 2:28 ` [RFC v4 2/3] arm64: boot: dts: qcom: sm8150: Enable dynamic TX FIFO resize logic Wesley Cheng 2020-06-24 2:28 ` [RFC v4 3/3] dt-bindings: usb: dwc3: Add entry for tx-fifo-resize Wesley Cheng 2 siblings, 2 replies; 13+ messages in thread From: Wesley Cheng @ 2020-06-24 2:28 UTC (permalink / raw) To: agross, bjorn.andersson, balbi, gregkh, robh+dt Cc: linux-kernel, devicetree, linux-arm-msm, linux-usb, jackp, Wesley Cheng Some devices have USB compositions which may require multiple endpoints that support EP bursting. HW defined TX FIFO sizes may not always be sufficient for these compositions. By utilizing flexible TX FIFO allocation, this allows for endpoints to request the required FIFO depth to achieve higher bandwidth. With some higher bMaxBurst configurations, using a larger TX FIFO size results in better TX throughput. Ensure that one TX FIFO is reserved for every IN endpoint. This allows for the FIFO logic to prevent running out of FIFO space. Signed-off-by: Wesley Cheng <wcheng@codeaurora.org> --- drivers/usb/dwc3/core.c | 2 + drivers/usb/dwc3/core.h | 8 +++ drivers/usb/dwc3/ep0.c | 37 +++++++++++- drivers/usb/dwc3/gadget.c | 115 ++++++++++++++++++++++++++++++++++++++ 4 files changed, 161 insertions(+), 1 deletion(-) diff --git a/drivers/usb/dwc3/core.c b/drivers/usb/dwc3/core.c index edc17155cb2b..cca555493929 100644 --- a/drivers/usb/dwc3/core.c +++ b/drivers/usb/dwc3/core.c @@ -1304,6 +1304,8 @@ static void dwc3_get_properties(struct dwc3 *dwc) &tx_thr_num_pkt_prd); device_property_read_u8(dev, "snps,tx-max-burst-prd", &tx_max_burst_prd); + dwc->needs_fifo_resize = device_property_read_bool(dev, + "tx-fifo-resize"); dwc->disable_scramble_quirk = device_property_read_bool(dev, "snps,disable_scramble_quirk"); diff --git a/drivers/usb/dwc3/core.h b/drivers/usb/dwc3/core.h index 4c171a8e215f..ce0bf288b6ac 100644 --- a/drivers/usb/dwc3/core.h +++ b/drivers/usb/dwc3/core.h @@ -675,6 +675,7 @@ struct dwc3_event_buffer { * isochronous START TRANSFER command failure workaround * @start_cmd_status: the status of testing START TRANSFER command with * combo_num = 'b00 + * @fifo_depth: allocated TXFIFO depth */ struct dwc3_ep { struct usb_ep endpoint; @@ -727,6 +728,7 @@ struct dwc3_ep { /* For isochronous START TRANSFER workaround only */ u8 combo_num; int start_cmd_status; + int fifo_depth; }; enum dwc3_phy { @@ -1004,6 +1006,7 @@ struct dwc3_scratchpad_array { * 1 - utmi_l1_suspend_n * @is_fpga: true when we are using the FPGA board * @pending_events: true when we have pending IRQs to be handled + * @needs_fifo_resize: not all users might want fifo resizing, flag it * @pullups_connected: true when Run/Stop bit is set * @setup_packet_pending: true when there's a Setup Packet in FIFO. Workaround * @three_stage_setup: set if we perform a three phase setup @@ -1044,6 +1047,8 @@ struct dwc3_scratchpad_array { * @dis_metastability_quirk: set to disable metastability quirk. * @imod_interval: set the interrupt moderation interval in 250ns * increments or 0 to disable. + * @last_fifo_depth: total TXFIFO depth of all enabled USB IN/INT endpoints + * @num_ep_resized: the number of TX FIFOs that have already been resized */ struct dwc3 { struct work_struct drd_work; @@ -1204,6 +1209,7 @@ struct dwc3 { unsigned is_utmi_l1_suspend:1; unsigned is_fpga:1; unsigned pending_events:1; + unsigned needs_fifo_resize:1; unsigned pullups_connected:1; unsigned setup_packet_pending:1; unsigned three_stage_setup:1; @@ -1236,6 +1242,8 @@ struct dwc3 { unsigned dis_metastability_quirk:1; u16 imod_interval; + int last_fifo_depth; + int num_ep_resized; }; #define INCRX_BURST_MODE 0 diff --git a/drivers/usb/dwc3/ep0.c b/drivers/usb/dwc3/ep0.c index 6dee4dabc0a4..76db9b530861 100644 --- a/drivers/usb/dwc3/ep0.c +++ b/drivers/usb/dwc3/ep0.c @@ -601,8 +601,9 @@ static int dwc3_ep0_set_config(struct dwc3 *dwc, struct usb_ctrlrequest *ctrl) { enum usb_device_state state = dwc->gadget.state; u32 cfg; - int ret; + int ret, num, size; u32 reg; + struct dwc3_ep *dep; cfg = le16_to_cpu(ctrl->wValue); @@ -611,6 +612,40 @@ static int dwc3_ep0_set_config(struct dwc3 *dwc, struct usb_ctrlrequest *ctrl) return -EINVAL; case USB_STATE_ADDRESS: + /* + * If tx-fifo-resize flag is not set for the controller, then + * do not clear existing allocated TXFIFO since we do not + * allocate it again in dwc3_gadget_resize_tx_fifos + */ + if (dwc->needs_fifo_resize) { + /* Read ep0IN related TXFIFO size */ + dep = dwc->eps[1]; + size = dwc3_readl(dwc->regs, DWC3_GTXFIFOSIZ(0)); + if (dwc3_is_usb31(dwc)) + dep->fifo_depth = DWC31_GTXFIFOSIZ_TXFDEP(size); + else + dep->fifo_depth = DWC3_GTXFIFOSIZ_TXFDEP(size); + + dwc->last_fifo_depth = dep->fifo_depth; + /* Clear existing TXFIFO for all IN eps except ep0 */ + for (num = 3; num < min_t(int, dwc->num_eps, + DWC3_ENDPOINTS_NUM); num += 2) { + dep = dwc->eps[num]; + /* Don't change TXFRAMNUM on usb31 version */ + size = dwc3_is_usb31(dwc) ? + dwc3_readl(dwc->regs, + DWC3_GTXFIFOSIZ(num >> 1)) & + DWC31_GTXFIFOSIZ_TXFRAMNUM : + 0; + + dwc3_writel(dwc->regs, + DWC3_GTXFIFOSIZ(num >> 1), + size); + dep->fifo_depth = 0; + } + dwc->num_ep_resized = 0; + } + ret = dwc3_ep0_delegate_req(dwc, ctrl); /* if the cfg matches and the cfg is non zero */ if (cfg && (!ret || (ret == USB_GADGET_DELAYED_STATUS))) { diff --git a/drivers/usb/dwc3/gadget.c b/drivers/usb/dwc3/gadget.c index 00746c2848c0..777badf3e85d 100644 --- a/drivers/usb/dwc3/gadget.c +++ b/drivers/usb/dwc3/gadget.c @@ -540,6 +540,117 @@ static int dwc3_gadget_start_config(struct dwc3_ep *dep) return 0; } +/* + * dwc3_gadget_resize_tx_fifos - reallocate fifo spaces for current use-case + * @dwc: pointer to our context structure + * + * This function will a best effort FIFO allocation in order + * to improve FIFO usage and throughput, while still allowing + * us to enable as many endpoints as possible. + * + * Keep in mind that this operation will be highly dependent + * on the configured size for RAM1 - which contains TxFifo -, + * the amount of endpoints enabled on coreConsultant tool, and + * the width of the Master Bus. + * + * In general, FIFO depths are represented with the following equation: + * + * fifo_size = mult * ((max_packet + mdwidth)/mdwidth + 1) + 1 + * + * Conversions can be done to the equation to derive the number of packets that + * will fit to a particular FIFO size value. + */ +static int dwc3_gadget_resize_tx_fifos(struct dwc3_ep *dep) +{ + struct dwc3 *dwc = dep->dwc; + int ram1_depth, mdwidth, fifo_0_start, tmp, num_in_ep; + int min_depth, remaining, fifo_size, mult = 1, fifo, max_packet = 1024; + + if (!dwc->needs_fifo_resize) + return 0; + + /* resize IN endpoints except ep0 */ + if (!usb_endpoint_dir_in(dep->endpoint.desc) || dep->number <= 1) + return 0; + + /* Don't resize already resized IN endpoint */ + if (dep->fifo_depth) + return 0; + + ram1_depth = DWC3_RAM1_DEPTH(dwc->hwparams.hwparams7); + mdwidth = DWC3_MDWIDTH(dwc->hwparams.hwparams0); + /* MDWIDTH is represented in bits, we need it in bytes */ + mdwidth >>= 3; + + if (((dep->endpoint.maxburst > 1) && + usb_endpoint_xfer_bulk(dep->endpoint.desc)) + || usb_endpoint_xfer_isoc(dep->endpoint.desc)) + mult = 3; + + if ((dep->endpoint.maxburst > 6) && + usb_endpoint_xfer_bulk(dep->endpoint.desc) + && dwc3_is_usb31(dwc)) + mult = 6; + + /* FIFO size for a single buffer */ + fifo = (max_packet + mdwidth)/mdwidth; + fifo++; + + /* Calculate the number of remaining EPs w/o any FIFO */ + num_in_ep = dwc->num_eps/2; + num_in_ep -= dwc->num_ep_resized; + /* Ignore EP0 IN */ + num_in_ep--; + + /* Reserve at least one FIFO for the number of IN EPs */ + min_depth = num_in_ep * (fifo+1); + remaining = ram1_depth - min_depth - dwc->last_fifo_depth; + + /* We've already reserved 1 FIFO per EP, so check what we can fit in + * addition to it. If there is not enough remaining space, allocate + * all the remaining space to the EP. + */ + fifo_size = (mult-1) * fifo; + if (remaining < fifo_size) { + if (remaining > 0) + fifo_size = remaining; + else + fifo_size = 0; + } + + fifo_size += fifo; + fifo_size++; + dep->fifo_depth = fifo_size; + + /* Check if TXFIFOs start at non-zero addr */ + tmp = dwc3_readl(dwc->regs, DWC3_GTXFIFOSIZ(0)); + fifo_0_start = DWC3_GTXFIFOSIZ_TXFSTADDR(tmp); + + fifo_size |= (fifo_0_start + (dwc->last_fifo_depth << 16)); + if (dwc3_is_usb31(dwc)) + dwc->last_fifo_depth += DWC31_GTXFIFOSIZ_TXFDEP(fifo_size); + else + dwc->last_fifo_depth += DWC3_GTXFIFOSIZ_TXFDEP(fifo_size); + + /* Check fifo size allocation doesn't exceed available RAM size. */ + if (dwc->last_fifo_depth >= ram1_depth) { + dev_err(dwc->dev, "Fifosize(%d) > RAM size(%d) %s depth:%d\n", + (dwc->last_fifo_depth * mdwidth), ram1_depth, + dep->endpoint.name, fifo_size); + if (dwc3_is_usb31(dwc)) + fifo_size = DWC31_GTXFIFOSIZ_TXFDEP(fifo_size); + else + fifo_size = DWC3_GTXFIFOSIZ_TXFDEP(fifo_size); + dwc->last_fifo_depth -= fifo_size; + dep->fifo_depth = 0; + return -ENOMEM; + } + + dwc3_writel(dwc->regs, DWC3_GTXFIFOSIZ(dep->number >> 1), fifo_size); + dwc->num_ep_resized++; + return 0; +} + static int dwc3_gadget_set_ep_config(struct dwc3_ep *dep, unsigned int action) { const struct usb_ss_ep_comp_descriptor *comp_desc; @@ -620,6 +731,10 @@ static int __dwc3_gadget_ep_enable(struct dwc3_ep *dep, unsigned int action) int ret; if (!(dep->flags & DWC3_EP_ENABLED)) { + ret = dwc3_gadget_resize_tx_fifos(dep); + if (ret) + return ret; + ret = dwc3_gadget_start_config(dep); if (ret) return ret; -- The Qualcomm Innovation Center, Inc. is a member of the Code Aurora Forum, a Linux Foundation Collaborative Project ^ permalink raw reply related [flat|nested] 13+ messages in thread
* Re: [RFC v4 1/3] usb: dwc3: Resize TX FIFOs to meet EP bursting requirements 2020-06-24 2:28 ` [RFC v4 1/3] usb: dwc3: Resize TX FIFOs to meet EP bursting requirements Wesley Cheng @ 2020-08-10 12:27 ` Felipe Balbi 2020-08-11 5:10 ` Wesley Cheng 2020-08-12 2:22 ` Peter Chen 1 sibling, 1 reply; 13+ messages in thread From: Felipe Balbi @ 2020-08-10 12:27 UTC (permalink / raw) To: Wesley Cheng, agross, bjorn.andersson, gregkh, robh+dt Cc: linux-kernel, devicetree, linux-arm-msm, linux-usb, jackp, Wesley Cheng [-- Attachment #1: Type: text/plain, Size: 7794 bytes --] Wesley Cheng <wcheng@codeaurora.org> writes: Hi, > Some devices have USB compositions which may require multiple endpoints > that support EP bursting. HW defined TX FIFO sizes may not always be > sufficient for these compositions. By utilizing flexible TX FIFO > allocation, this allows for endpoints to request the required FIFO depth to > achieve higher bandwidth. With some higher bMaxBurst configurations, using > a larger TX FIFO size results in better TX throughput. how much better? What's the impact? Got some real numbers of this running with upstream kernel? I guess mass storage gadget is the simplest one to test. > diff --git a/drivers/usb/dwc3/ep0.c b/drivers/usb/dwc3/ep0.c > index 6dee4dabc0a4..76db9b530861 100644 > --- a/drivers/usb/dwc3/ep0.c > +++ b/drivers/usb/dwc3/ep0.c > @@ -601,8 +601,9 @@ static int dwc3_ep0_set_config(struct dwc3 *dwc, struct usb_ctrlrequest *ctrl) > { > enum usb_device_state state = dwc->gadget.state; > u32 cfg; > - int ret; > + int ret, num, size; no, no. Please one declaration per line. > u32 reg; > + struct dwc3_ep *dep; Keep reverse xmas tree order. > @@ -611,6 +612,40 @@ static int dwc3_ep0_set_config(struct dwc3 *dwc, struct usb_ctrlrequest *ctrl) > return -EINVAL; > > case USB_STATE_ADDRESS: > + /* > + * If tx-fifo-resize flag is not set for the controller, then > + * do not clear existing allocated TXFIFO since we do not > + * allocate it again in dwc3_gadget_resize_tx_fifos > + */ > + if (dwc->needs_fifo_resize) { > + /* Read ep0IN related TXFIFO size */ > + dep = dwc->eps[1]; > + size = dwc3_readl(dwc->regs, DWC3_GTXFIFOSIZ(0)); > + if (dwc3_is_usb31(dwc)) > + dep->fifo_depth = DWC31_GTXFIFOSIZ_TXFDEP(size); > + else > + dep->fifo_depth = DWC3_GTXFIFOSIZ_TXFDEP(size); > + > + dwc->last_fifo_depth = dep->fifo_depth; > + /* Clear existing TXFIFO for all IN eps except ep0 */ > + for (num = 3; num < min_t(int, dwc->num_eps, > + DWC3_ENDPOINTS_NUM); num += 2) { > + dep = dwc->eps[num]; > + /* Don't change TXFRAMNUM on usb31 version */ > + size = dwc3_is_usb31(dwc) ? > + dwc3_readl(dwc->regs, > + DWC3_GTXFIFOSIZ(num >> 1)) & > + DWC31_GTXFIFOSIZ_TXFRAMNUM : > + 0; > + > + dwc3_writel(dwc->regs, > + DWC3_GTXFIFOSIZ(num >> 1), > + size); > + dep->fifo_depth = 0; > + } > + dwc->num_ep_resized = 0; care to move this into a helper that you call unconditionally and the helper returns early is !needs_fifo_resize? > diff --git a/drivers/usb/dwc3/gadget.c b/drivers/usb/dwc3/gadget.c > index 00746c2848c0..777badf3e85d 100644 > --- a/drivers/usb/dwc3/gadget.c > +++ b/drivers/usb/dwc3/gadget.c > @@ -540,6 +540,117 @@ static int dwc3_gadget_start_config(struct dwc3_ep *dep) > return 0; > } > > +/* > + * dwc3_gadget_resize_tx_fifos - reallocate fifo spaces for current use-case > + * @dwc: pointer to our context structure > + * > + * This function will a best effort FIFO allocation in order > + * to improve FIFO usage and throughput, while still allowing > + * us to enable as many endpoints as possible. > + * > + * Keep in mind that this operation will be highly dependent > + * on the configured size for RAM1 - which contains TxFifo -, > + * the amount of endpoints enabled on coreConsultant tool, and > + * the width of the Master Bus. > + * > + * In general, FIFO depths are represented with the following equation: > + * > + * fifo_size = mult * ((max_packet + mdwidth)/mdwidth + 1) + 1 > + * > + * Conversions can be done to the equation to derive the number of packets that > + * will fit to a particular FIFO size value. > + */ > +static int dwc3_gadget_resize_tx_fifos(struct dwc3_ep *dep) > +{ > + struct dwc3 *dwc = dep->dwc; > + int ram1_depth, mdwidth, fifo_0_start, tmp, num_in_ep; > + int min_depth, remaining, fifo_size, mult = 1, fifo, max_packet = 1024; one declaration per line, also make sure you order it in reverse xmas tree order. > + if (!dwc->needs_fifo_resize) > + return 0; > + > + /* resize IN endpoints except ep0 */ > + if (!usb_endpoint_dir_in(dep->endpoint.desc) || dep->number <= 1) > + return 0; > + > + /* Don't resize already resized IN endpoint */ > + if (dep->fifo_depth) using fifo_depth as a flag seems flakey to me. What happens when someone in the future changes the behavior below and this doesn't apply anymore? Also, why is this procedure called more than once for the same endpoint? Does that really happen? > + return 0; > + > + ram1_depth = DWC3_RAM1_DEPTH(dwc->hwparams.hwparams7); > + mdwidth = DWC3_MDWIDTH(dwc->hwparams.hwparams0); > + /* MDWIDTH is represented in bits, we need it in bytes */ > + mdwidth >>= 3; > + > + if (((dep->endpoint.maxburst > 1) && > + usb_endpoint_xfer_bulk(dep->endpoint.desc)) > + || usb_endpoint_xfer_isoc(dep->endpoint.desc)) > + mult = 3; > + > + if ((dep->endpoint.maxburst > 6) && > + usb_endpoint_xfer_bulk(dep->endpoint.desc) > + && dwc3_is_usb31(dwc)) > + mult = 6; > + > + /* FIFO size for a single buffer */ > + fifo = (max_packet + mdwidth)/mdwidth; add spaces around integer division operator > + fifo++; > + > + /* Calculate the number of remaining EPs w/o any FIFO */ > + num_in_ep = dwc->num_eps/2; > + num_in_ep -= dwc->num_ep_resized; > + /* Ignore EP0 IN */ > + num_in_ep--; > + > + /* Reserve at least one FIFO for the number of IN EPs */ > + min_depth = num_in_ep * (fifo+1); > + remaining = ram1_depth - min_depth - dwc->last_fifo_depth; > + > + /* We've already reserved 1 FIFO per EP, so check what we can fit in comment style is wrong > + * addition to it. If there is not enough remaining space, allocate > + * all the remaining space to the EP. > + */ > + fifo_size = (mult-1) * fifo; spaces around subtraction > + if (remaining < fifo_size) { > + if (remaining > 0) > + fifo_size = remaining; > + else > + fifo_size = 0; > + } > + > + fifo_size += fifo; > + fifo_size++; why the increment? > + dep->fifo_depth = fifo_size; > + > + /* Check if TXFIFOs start at non-zero addr */ > + tmp = dwc3_readl(dwc->regs, DWC3_GTXFIFOSIZ(0)); > + fifo_0_start = DWC3_GTXFIFOSIZ_TXFSTADDR(tmp); > + > + fifo_size |= (fifo_0_start + (dwc->last_fifo_depth << 16)); > + if (dwc3_is_usb31(dwc)) > + dwc->last_fifo_depth += DWC31_GTXFIFOSIZ_TXFDEP(fifo_size); > + else > + dwc->last_fifo_depth += DWC3_GTXFIFOSIZ_TXFDEP(fifo_size); > + > + /* Check fifo size allocation doesn't exceed available RAM size. */ > + if (dwc->last_fifo_depth >= ram1_depth) { > + dev_err(dwc->dev, "Fifosize(%d) > RAM size(%d) %s depth:%d\n", > + (dwc->last_fifo_depth * mdwidth), ram1_depth, > + dep->endpoint.name, fifo_size); > + if (dwc3_is_usb31(dwc)) > + fifo_size = DWC31_GTXFIFOSIZ_TXFDEP(fifo_size); > + else > + fifo_size = DWC3_GTXFIFOSIZ_TXFDEP(fifo_size); > + dwc->last_fifo_depth -= fifo_size; > + dep->fifo_depth = 0; > + return -ENOMEM; > + } > + > + dwc3_writel(dwc->regs, DWC3_GTXFIFOSIZ(dep->number >> 1), fifo_size); > + dwc->num_ep_resized++; add a blank line here > + return 0; > +} > + > static int dwc3_gadget_set_ep_config(struct dwc3_ep *dep, unsigned int action) > { > const struct usb_ss_ep_comp_descriptor *comp_desc; > @@ -620,6 +731,10 @@ static int __dwc3_gadget_ep_enable(struct dwc3_ep *dep, unsigned int action) > int ret; > > if (!(dep->flags & DWC3_EP_ENABLED)) { > + ret = dwc3_gadget_resize_tx_fifos(dep); > + if (ret) > + return ret; doesn't it look odd that you're resizing every fifo every time a new endpoint is enabled? Is there a better way to achieve this? -- balbi [-- Attachment #2: signature.asc --] [-- Type: application/pgp-signature, Size: 832 bytes --] ^ permalink raw reply [flat|nested] 13+ messages in thread
* Re: [RFC v4 1/3] usb: dwc3: Resize TX FIFOs to meet EP bursting requirements 2020-08-10 12:27 ` Felipe Balbi @ 2020-08-11 5:10 ` Wesley Cheng 2020-08-11 7:12 ` Felipe Balbi 0 siblings, 1 reply; 13+ messages in thread From: Wesley Cheng @ 2020-08-11 5:10 UTC (permalink / raw) To: Felipe Balbi, agross, bjorn.andersson, gregkh, robh+dt Cc: linux-kernel, devicetree, linux-arm-msm, linux-usb, jackp On 8/10/2020 5:27 AM, Felipe Balbi wrote: > Wesley Cheng <wcheng@codeaurora.org> writes: > > Hi, > >> Some devices have USB compositions which may require multiple endpoints >> that support EP bursting. HW defined TX FIFO sizes may not always be >> sufficient for these compositions. By utilizing flexible TX FIFO >> allocation, this allows for endpoints to request the required FIFO depth to >> achieve higher bandwidth. With some higher bMaxBurst configurations, using >> a larger TX FIFO size results in better TX throughput. > > how much better? What's the impact? Got some real numbers of this > running with upstream kernel? I guess mass storage gadget is the > simplest one to test. > Hi Felipe, Thanks for the input. Sorry for not including the numbers in the patch itself, but I did mention the set of mass storage tests I ran w/ the upstream kernel on SM8150 in the cover letter. Let me just share that here: Test Parameters: - Platform: Qualcomm SM8150 - bMaxBurst = 6 - USB req size = 256kB - Num of USB reqs = 16 - USB Speed = Super-Speed - Function Driver: Mass Storage (w/ ramdisk) - Test Application: CrystalDiskMark Results: TXFIFO Depth = 3 max packets Test Case | Data Size | AVG tput (in MB/s) ------------------------------------------- Sequential|1 GB x | Read |9 loops | 193.60 | | 195.86 | | 184.77 | | 193.60 ------------------------------------------- TXFIFO Depth = 6 max packets Test Case | Data Size | AVG tput (in MB/s) ------------------------------------------- Sequential|1 GB x | Read |9 loops | 287.35 | | 304.94 | | 289.64 | | 293.61 ------------------------------------------- >> diff --git a/drivers/usb/dwc3/ep0.c b/drivers/usb/dwc3/ep0.c >> index 6dee4dabc0a4..76db9b530861 100644 >> --- a/drivers/usb/dwc3/ep0.c >> +++ b/drivers/usb/dwc3/ep0.c >> @@ -601,8 +601,9 @@ static int dwc3_ep0_set_config(struct dwc3 *dwc, struct usb_ctrlrequest *ctrl) >> { >> enum usb_device_state state = dwc->gadget.state; >> u32 cfg; >> - int ret; >> + int ret, num, size; > > no, no. Please one declaration per line. > Got it. >> u32 reg; >> + struct dwc3_ep *dep; > > Keep reverse xmas tree order. > Understood. >> @@ -611,6 +612,40 @@ static int dwc3_ep0_set_config(struct dwc3 *dwc, struct usb_ctrlrequest *ctrl) >> return -EINVAL; >> >> case USB_STATE_ADDRESS: >> + /* >> + * If tx-fifo-resize flag is not set for the controller, then >> + * do not clear existing allocated TXFIFO since we do not >> + * allocate it again in dwc3_gadget_resize_tx_fifos >> + */ >> + if (dwc->needs_fifo_resize) { >> + /* Read ep0IN related TXFIFO size */ >> + dep = dwc->eps[1]; >> + size = dwc3_readl(dwc->regs, DWC3_GTXFIFOSIZ(0)); >> + if (dwc3_is_usb31(dwc)) >> + dep->fifo_depth = DWC31_GTXFIFOSIZ_TXFDEP(size); >> + else >> + dep->fifo_depth = DWC3_GTXFIFOSIZ_TXFDEP(size); >> + >> + dwc->last_fifo_depth = dep->fifo_depth; >> + /* Clear existing TXFIFO for all IN eps except ep0 */ >> + for (num = 3; num < min_t(int, dwc->num_eps, >> + DWC3_ENDPOINTS_NUM); num += 2) { >> + dep = dwc->eps[num]; >> + /* Don't change TXFRAMNUM on usb31 version */ >> + size = dwc3_is_usb31(dwc) ? >> + dwc3_readl(dwc->regs, >> + DWC3_GTXFIFOSIZ(num >> 1)) & >> + DWC31_GTXFIFOSIZ_TXFRAMNUM : >> + 0; >> + >> + dwc3_writel(dwc->regs, >> + DWC3_GTXFIFOSIZ(num >> 1), >> + size); >> + dep->fifo_depth = 0; >> + } >> + dwc->num_ep_resized = 0; > > care to move this into a helper that you call unconditionally and the > helper returns early is !needs_fifo_resize? > Sure, I'll include that in the next revision. >> diff --git a/drivers/usb/dwc3/gadget.c b/drivers/usb/dwc3/gadget.c >> index 00746c2848c0..777badf3e85d 100644 >> --- a/drivers/usb/dwc3/gadget.c >> +++ b/drivers/usb/dwc3/gadget.c >> @@ -540,6 +540,117 @@ static int dwc3_gadget_start_config(struct dwc3_ep *dep) >> return 0; >> } >> >> +/* >> + * dwc3_gadget_resize_tx_fifos - reallocate fifo spaces for current use-case >> + * @dwc: pointer to our context structure >> + * >> + * This function will a best effort FIFO allocation in order >> + * to improve FIFO usage and throughput, while still allowing >> + * us to enable as many endpoints as possible. >> + * >> + * Keep in mind that this operation will be highly dependent >> + * on the configured size for RAM1 - which contains TxFifo -, >> + * the amount of endpoints enabled on coreConsultant tool, and >> + * the width of the Master Bus. >> + * >> + * In general, FIFO depths are represented with the following equation: >> + * >> + * fifo_size = mult * ((max_packet + mdwidth)/mdwidth + 1) + 1 >> + * >> + * Conversions can be done to the equation to derive the number of packets that >> + * will fit to a particular FIFO size value. >> + */ >> +static int dwc3_gadget_resize_tx_fifos(struct dwc3_ep *dep) >> +{ >> + struct dwc3 *dwc = dep->dwc; >> + int ram1_depth, mdwidth, fifo_0_start, tmp, num_in_ep; >> + int min_depth, remaining, fifo_size, mult = 1, fifo, max_packet = 1024; > > one declaration per line, also make sure you order it in reverse xmas > tree order. > Will make sure to fix this in further declarations. >> + if (!dwc->needs_fifo_resize) >> + return 0; >> + >> + /* resize IN endpoints except ep0 */ >> + if (!usb_endpoint_dir_in(dep->endpoint.desc) || dep->number <= 1) >> + return 0; >> + >> + /* Don't resize already resized IN endpoint */ >> + if (dep->fifo_depth) > > using fifo_depth as a flag seems flakey to me. What happens when someone > in the future changes the behavior below and this doesn't apply anymore? > > Also, why is this procedure called more than once for the same endpoint? > Does that really happen? > I guess it can be considered a bug elsewhere (ie usb gadget or function driver) if this happens twice. Plus, if we decide to keep this in the dwc3 enable endpoint path, the DWC3_EP_ENABLED flag will ensure it's called only once as well. Its probably overkill to check fifo_depth here. >> + return 0; >> + >> + ram1_depth = DWC3_RAM1_DEPTH(dwc->hwparams.hwparams7); >> + mdwidth = DWC3_MDWIDTH(dwc->hwparams.hwparams0); >> + /* MDWIDTH is represented in bits, we need it in bytes */ >> + mdwidth >>= 3; >> + >> + if (((dep->endpoint.maxburst > 1) && >> + usb_endpoint_xfer_bulk(dep->endpoint.desc)) >> + || usb_endpoint_xfer_isoc(dep->endpoint.desc)) >> + mult = 3; >> + >> + if ((dep->endpoint.maxburst > 6) && >> + usb_endpoint_xfer_bulk(dep->endpoint.desc) >> + && dwc3_is_usb31(dwc)) >> + mult = 6; >> + >> + /* FIFO size for a single buffer */ >> + fifo = (max_packet + mdwidth)/mdwidth; > > add spaces around integer division operator > >> + fifo++; >> + >> + /* Calculate the number of remaining EPs w/o any FIFO */ >> + num_in_ep = dwc->num_eps/2; >> + num_in_ep -= dwc->num_ep_resized; >> + /* Ignore EP0 IN */ >> + num_in_ep--; >> + >> + /* Reserve at least one FIFO for the number of IN EPs */ >> + min_depth = num_in_ep * (fifo+1); >> + remaining = ram1_depth - min_depth - dwc->last_fifo_depth; >> + >> + /* We've already reserved 1 FIFO per EP, so check what we can fit in > > comment style is wrong > >> + * addition to it. If there is not enough remaining space, allocate >> + * all the remaining space to the EP. >> + */ >> + fifo_size = (mult-1) * fifo; > > spaces around subtraction > Will fix the formatting comments above. >> + if (remaining < fifo_size) { >> + if (remaining > 0) >> + fifo_size = remaining; >> + else >> + fifo_size = 0; >> + } >> + >> + fifo_size += fifo; >> + fifo_size++; > > why the increment? > This is to account for the last +1 in the equation from the DWC3 databook: fifo_size = mult * ((max_packet + mdwidth)/mdwidth + 1) + 1 <- this one >> + dep->fifo_depth = fifo_size; >> + >> + /* Check if TXFIFOs start at non-zero addr */ >> + tmp = dwc3_readl(dwc->regs, DWC3_GTXFIFOSIZ(0)); >> + fifo_0_start = DWC3_GTXFIFOSIZ_TXFSTADDR(tmp); >> + >> + fifo_size |= (fifo_0_start + (dwc->last_fifo_depth << 16)); >> + if (dwc3_is_usb31(dwc)) >> + dwc->last_fifo_depth += DWC31_GTXFIFOSIZ_TXFDEP(fifo_size); >> + else >> + dwc->last_fifo_depth += DWC3_GTXFIFOSIZ_TXFDEP(fifo_size); >> + >> + /* Check fifo size allocation doesn't exceed available RAM size. */ >> + if (dwc->last_fifo_depth >= ram1_depth) { >> + dev_err(dwc->dev, "Fifosize(%d) > RAM size(%d) %s depth:%d\n", >> + (dwc->last_fifo_depth * mdwidth), ram1_depth, >> + dep->endpoint.name, fifo_size); >> + if (dwc3_is_usb31(dwc)) >> + fifo_size = DWC31_GTXFIFOSIZ_TXFDEP(fifo_size); >> + else >> + fifo_size = DWC3_GTXFIFOSIZ_TXFDEP(fifo_size); >> + dwc->last_fifo_depth -= fifo_size; >> + dep->fifo_depth = 0; >> + return -ENOMEM; >> + } >> + >> + dwc3_writel(dwc->regs, DWC3_GTXFIFOSIZ(dep->number >> 1), fifo_size); >> + dwc->num_ep_resized++; > > add a blank line here > >> + return 0; >> +} >> + >> static int dwc3_gadget_set_ep_config(struct dwc3_ep *dep, unsigned int action) >> { >> const struct usb_ss_ep_comp_descriptor *comp_desc; >> @@ -620,6 +731,10 @@ static int __dwc3_gadget_ep_enable(struct dwc3_ep *dep, unsigned int action) >> int ret; >> >> if (!(dep->flags & DWC3_EP_ENABLED)) { >> + ret = dwc3_gadget_resize_tx_fifos(dep); >> + if (ret) >> + return ret; > > doesn't it look odd that you're resizing every fifo every time a new > endpoint is enabled? Is there a better way to achieve this? > We're only resizing a single fifo per call, and clearing the previous fifo configuration upon receiving the set address. In the past, I know the change was to resize all fifos after receiving the set configuration packet. With that approach, I believe we saw issues with some function drivers that immediately queued a USB request during their set_alt() routine, followed by the dwc3 ep0 driver calling the TX fifo resize API.(as the tx fifo resize was executed after we delegated the set config packet to the USB composite) Thanks Wesley -- The Qualcomm Innovation Center, Inc. is a member of the Code Aurora Forum, a Linux Foundation Collaborative Project ^ permalink raw reply [flat|nested] 13+ messages in thread
* Re: [RFC v4 1/3] usb: dwc3: Resize TX FIFOs to meet EP bursting requirements 2020-08-11 5:10 ` Wesley Cheng @ 2020-08-11 7:12 ` Felipe Balbi 2020-08-11 13:44 ` Alan Stern 2020-08-12 18:34 ` Wesley Cheng 0 siblings, 2 replies; 13+ messages in thread From: Felipe Balbi @ 2020-08-11 7:12 UTC (permalink / raw) To: Wesley Cheng, agross, bjorn.andersson, gregkh, robh+dt Cc: linux-kernel, devicetree, linux-arm-msm, linux-usb, jackp [-- Attachment #1: Type: text/plain, Size: 5472 bytes --] Hi, Wesley Cheng <wcheng@codeaurora.org> writes: > On 8/10/2020 5:27 AM, Felipe Balbi wrote: >> Wesley Cheng <wcheng@codeaurora.org> writes: >> >> Hi, >> >>> Some devices have USB compositions which may require multiple endpoints >>> that support EP bursting. HW defined TX FIFO sizes may not always be >>> sufficient for these compositions. By utilizing flexible TX FIFO >>> allocation, this allows for endpoints to request the required FIFO depth to >>> achieve higher bandwidth. With some higher bMaxBurst configurations, using >>> a larger TX FIFO size results in better TX throughput. >> >> how much better? What's the impact? Got some real numbers of this >> running with upstream kernel? I guess mass storage gadget is the >> simplest one to test. >> > Hi Felipe, > > Thanks for the input. > > Sorry for not including the numbers in the patch itself, but I did > mention the set of mass storage tests I ran w/ the upstream kernel on > SM8150 in the cover letter. Let me just share that here: > > Test Parameters: > - Platform: Qualcomm SM8150 > - bMaxBurst = 6 > - USB req size = 256kB > - Num of USB reqs = 16 > - USB Speed = Super-Speed > - Function Driver: Mass Storage (w/ ramdisk) > - Test Application: CrystalDiskMark > > Results: > > TXFIFO Depth = 3 max packets > > Test Case | Data Size | AVG tput (in MB/s) > ------------------------------------------- > Sequential|1 GB x | > Read |9 loops | 193.60 > | | 195.86 > | | 184.77 > | | 193.60 > ------------------------------------------- > > TXFIFO Depth = 6 max packets > > Test Case | Data Size | AVG tput (in MB/s) > ------------------------------------------- > Sequential|1 GB x | > Read |9 loops | 287.35 > | | 304.94 > | | 289.64 > | | 293.61 > ------------------------------------------- awesome, thanks a lot for this :-) It's a considerable increase in your setup. My only fear here is that we may end up creating a situation where we can't allocate enough FIFO for all endpoints. This is, of course, a consequence of the fact that we enable one endpoint at a time. Perhaps we could envision a way where function driver requests endpoints in bulk, i.e. combines all endpoint requirements into a single method call for gadget framework and, consequently, for UDC. >>> + if (!dwc->needs_fifo_resize) >>> + return 0; >>> + >>> + /* resize IN endpoints except ep0 */ >>> + if (!usb_endpoint_dir_in(dep->endpoint.desc) || dep->number <= 1) >>> + return 0; >>> + >>> + /* Don't resize already resized IN endpoint */ >>> + if (dep->fifo_depth) >> >> using fifo_depth as a flag seems flakey to me. What happens when someone >> in the future changes the behavior below and this doesn't apply anymore? >> >> Also, why is this procedure called more than once for the same endpoint? >> Does that really happen? >> > I guess it can be considered a bug elsewhere (ie usb gadget or function > driver) if this happens twice. Plus, if we decide to keep this in the > dwc3 enable endpoint path, the DWC3_EP_ENABLED flag will ensure it's > called only once as well. Its probably overkill to check fifo_depth here. We could add a dev_WARN_ONCE() just to catch any possible bugs elsewhere. >>> + if (remaining < fifo_size) { >>> + if (remaining > 0) >>> + fifo_size = remaining; >>> + else >>> + fifo_size = 0; >>> + } >>> + >>> + fifo_size += fifo; >>> + fifo_size++; >> >> why the increment? >> > This is to account for the last +1 in the equation from the DWC3 databook: > fifo_size = mult * ((max_packet + mdwidth)/mdwidth + 1) + 1 <- this one great, could you add this detail as a comment so it doesn't look as cryptic? :-) >>> + return 0; >>> +} >>> + >>> static int dwc3_gadget_set_ep_config(struct dwc3_ep *dep, unsigned int action) >>> { >>> const struct usb_ss_ep_comp_descriptor *comp_desc; >>> @@ -620,6 +731,10 @@ static int __dwc3_gadget_ep_enable(struct dwc3_ep *dep, unsigned int action) >>> int ret; >>> >>> if (!(dep->flags & DWC3_EP_ENABLED)) { >>> + ret = dwc3_gadget_resize_tx_fifos(dep); >>> + if (ret) >>> + return ret; >> >> doesn't it look odd that you're resizing every fifo every time a new >> endpoint is enabled? Is there a better way to achieve this? >> > We're only resizing a single fifo per call, and clearing the previous > fifo configuration upon receiving the set address. In the past, I know > the change was to resize all fifos after receiving the set configuration > packet. With that approach, I believe we saw issues with some function > drivers that immediately queued a USB request during their set_alt() > routine, followed by the dwc3 ep0 driver calling the TX fifo resize > API.(as the tx fifo resize was executed after we delegated the set > config packet to the USB composite) I don't remember seeing such an issue. Allocating FIFOs after we know the entire requirements would avoid another possible situation, that of dwc3 exausting FIFO space before it knows there are more enpdoints to enable. One possibility around this was suggested above, something along the lines of: usb_gadget_ep_enable_bulk(struct usb_gadget *, struct usb_ep_alloc_desc *alloc_desc) (please think of better names, I'm hopeless haha) -- balbi [-- Attachment #2: signature.asc --] [-- Type: application/pgp-signature, Size: 832 bytes --] ^ permalink raw reply [flat|nested] 13+ messages in thread
* Re: [RFC v4 1/3] usb: dwc3: Resize TX FIFOs to meet EP bursting requirements 2020-08-11 7:12 ` Felipe Balbi @ 2020-08-11 13:44 ` Alan Stern 2020-08-12 18:34 ` Wesley Cheng 1 sibling, 0 replies; 13+ messages in thread From: Alan Stern @ 2020-08-11 13:44 UTC (permalink / raw) To: Felipe Balbi Cc: Wesley Cheng, agross, bjorn.andersson, gregkh, robh+dt, linux-kernel, devicetree, linux-arm-msm, linux-usb, jackp On Tue, Aug 11, 2020 at 10:12:41AM +0300, Felipe Balbi wrote: > One possibility around this was suggested above, something along the > lines of: > > usb_gadget_ep_enable_bulk(struct usb_gadget *, struct > usb_ep_alloc_desc *alloc_desc) > > (please think of better names, I'm hopeless haha) How about usb_gadget_enable_endpoints()? Alan Stern ^ permalink raw reply [flat|nested] 13+ messages in thread
* Re: [RFC v4 1/3] usb: dwc3: Resize TX FIFOs to meet EP bursting requirements 2020-08-11 7:12 ` Felipe Balbi 2020-08-11 13:44 ` Alan Stern @ 2020-08-12 18:34 ` Wesley Cheng 2020-08-18 19:58 ` Wesley Cheng 1 sibling, 1 reply; 13+ messages in thread From: Wesley Cheng @ 2020-08-12 18:34 UTC (permalink / raw) To: Felipe Balbi, agross, bjorn.andersson, gregkh, robh+dt Cc: linux-kernel, devicetree, linux-arm-msm, linux-usb, jackp On 8/11/2020 12:12 AM, Felipe Balbi wrote: > > Hi, > > Wesley Cheng <wcheng@codeaurora.org> writes: >> On 8/10/2020 5:27 AM, Felipe Balbi wrote: >>> Wesley Cheng <wcheng@codeaurora.org> writes: >>> >>> Hi, >>> >>>> Some devices have USB compositions which may require multiple endpoints >>>> that support EP bursting. HW defined TX FIFO sizes may not always be >>>> sufficient for these compositions. By utilizing flexible TX FIFO >>>> allocation, this allows for endpoints to request the required FIFO depth to >>>> achieve higher bandwidth. With some higher bMaxBurst configurations, using >>>> a larger TX FIFO size results in better TX throughput. >>> >>> how much better? What's the impact? Got some real numbers of this >>> running with upstream kernel? I guess mass storage gadget is the >>> simplest one to test. >>> >> Hi Felipe, >> >> Thanks for the input. >> >> Sorry for not including the numbers in the patch itself, but I did >> mention the set of mass storage tests I ran w/ the upstream kernel on >> SM8150 in the cover letter. Let me just share that here: >> >> Test Parameters: >> - Platform: Qualcomm SM8150 >> - bMaxBurst = 6 >> - USB req size = 256kB >> - Num of USB reqs = 16 >> - USB Speed = Super-Speed >> - Function Driver: Mass Storage (w/ ramdisk) >> - Test Application: CrystalDiskMark >> >> Results: >> >> TXFIFO Depth = 3 max packets >> >> Test Case | Data Size | AVG tput (in MB/s) >> ------------------------------------------- >> Sequential|1 GB x | >> Read |9 loops | 193.60 >> | | 195.86 >> | | 184.77 >> | | 193.60 >> ------------------------------------------- >> >> TXFIFO Depth = 6 max packets >> >> Test Case | Data Size | AVG tput (in MB/s) >> ------------------------------------------- >> Sequential|1 GB x | >> Read |9 loops | 287.35 >> | | 304.94 >> | | 289.64 >> | | 293.61 >> ------------------------------------------- > > awesome, thanks a lot for this :-) It's a considerable increase in your > setup. My only fear here is that we may end up creating a situation > where we can't allocate enough FIFO for all endpoints. This is, of > course, a consequence of the fact that we enable one endpoint at a > time. > > Perhaps we could envision a way where function driver requests endpoints > in bulk, i.e. combines all endpoint requirements into a single method > call for gadget framework and, consequently, for UDC. > Hi Felipe, I agree...Resizing the txfifo is not as straightforward as it sounds :). Would be interesting to see how this affects tput on other platforms as well. We had a few discussions within our team, and came up with the logic implemented in this patch to reserve at least 1 txfifo per endpoint. Then we allocate any additional fifo space requests based on the remaining space left. That way we could avoid over allocating, but the trade off is that we may have unused EPs taking up fifo space. I didn't consider branching out to changing the gadget framework, so let me take a look at your suggestion to see how it turns out. >>>> + if (!dwc->needs_fifo_resize) >>>> + return 0; >>>> + >>>> + /* resize IN endpoints except ep0 */ >>>> + if (!usb_endpoint_dir_in(dep->endpoint.desc) || dep->number <= 1) >>>> + return 0; >>>> + >>>> + /* Don't resize already resized IN endpoint */ >>>> + if (dep->fifo_depth) >>> >>> using fifo_depth as a flag seems flakey to me. What happens when someone >>> in the future changes the behavior below and this doesn't apply anymore? >>> >>> Also, why is this procedure called more than once for the same endpoint? >>> Does that really happen? >>> >> I guess it can be considered a bug elsewhere (ie usb gadget or function >> driver) if this happens twice. Plus, if we decide to keep this in the >> dwc3 enable endpoint path, the DWC3_EP_ENABLED flag will ensure it's >> called only once as well. Its probably overkill to check fifo_depth here. > > We could add a dev_WARN_ONCE() just to catch any possible bugs elsewhere. > OK, I can add that. >>>> + if (remaining < fifo_size) { >>>> + if (remaining > 0) >>>> + fifo_size = remaining; >>>> + else >>>> + fifo_size = 0; >>>> + } >>>> + >>>> + fifo_size += fifo; >>>> + fifo_size++; >>> >>> why the increment? >>> >> This is to account for the last +1 in the equation from the DWC3 databook: >> fifo_size = mult * ((max_packet + mdwidth)/mdwidth + 1) + 1 <- this one > > great, could you add this detail as a comment so it doesn't look as > cryptic? :-) > Sure, of course. >>>> + return 0; >>>> +} >>>> + >>>> static int dwc3_gadget_set_ep_config(struct dwc3_ep *dep, unsigned int action) >>>> { >>>> const struct usb_ss_ep_comp_descriptor *comp_desc; >>>> @@ -620,6 +731,10 @@ static int __dwc3_gadget_ep_enable(struct dwc3_ep *dep, unsigned int action) >>>> int ret; >>>> >>>> if (!(dep->flags & DWC3_EP_ENABLED)) { >>>> + ret = dwc3_gadget_resize_tx_fifos(dep); >>>> + if (ret) >>>> + return ret; >>> >>> doesn't it look odd that you're resizing every fifo every time a new >>> endpoint is enabled? Is there a better way to achieve this? >>> >> We're only resizing a single fifo per call, and clearing the previous >> fifo configuration upon receiving the set address. In the past, I know >> the change was to resize all fifos after receiving the set configuration >> packet. With that approach, I believe we saw issues with some function >> drivers that immediately queued a USB request during their set_alt() >> routine, followed by the dwc3 ep0 driver calling the TX fifo resize >> API.(as the tx fifo resize was executed after we delegated the set >> config packet to the USB composite) > > I don't remember seeing such an issue. Allocating FIFOs after we know > the entire requirements would avoid another possible situation, that of > dwc3 exausting FIFO space before it knows there are more enpdoints to > enable. > > One possibility around this was suggested above, something along the > lines of: > > usb_gadget_ep_enable_bulk(struct usb_gadget *, struct > usb_ep_alloc_desc *alloc_desc) > > (please think of better names, I'm hopeless haha) > Sorry forgot to mention that this is something we caught internally with our testing using the older txfifo resizing change. As mentioned above, let me dive into this suggestion a bit more. Thanks Wesley -- The Qualcomm Innovation Center, Inc. is a member of the Code Aurora Forum, a Linux Foundation Collaborative Project ^ permalink raw reply [flat|nested] 13+ messages in thread
* Re: [RFC v4 1/3] usb: dwc3: Resize TX FIFOs to meet EP bursting requirements 2020-08-12 18:34 ` Wesley Cheng @ 2020-08-18 19:58 ` Wesley Cheng 0 siblings, 0 replies; 13+ messages in thread From: Wesley Cheng @ 2020-08-18 19:58 UTC (permalink / raw) To: Felipe Balbi, agross, bjorn.andersson, gregkh, robh+dt Cc: linux-kernel, devicetree, linux-arm-msm, linux-usb, jackp On 8/12/2020 11:34 AM, Wesley Cheng wrote: >> >> awesome, thanks a lot for this :-) It's a considerable increase in your >> setup. My only fear here is that we may end up creating a situation >> where we can't allocate enough FIFO for all endpoints. This is, of >> course, a consequence of the fact that we enable one endpoint at a >> time. >> >> Perhaps we could envision a way where function driver requests endpoints >> in bulk, i.e. combines all endpoint requirements into a single method >> call for gadget framework and, consequently, for UDC. >> > Hi Felipe, > > I agree...Resizing the txfifo is not as straightforward as it sounds :). > Would be interesting to see how this affects tput on other platforms as > well. We had a few discussions within our team, and came up with the > logic implemented in this patch to reserve at least 1 txfifo per > endpoint. Then we allocate any additional fifo space requests based on > the remaining space left. That way we could avoid over allocating, but > the trade off is that we may have unused EPs taking up fifo space. > > I didn't consider branching out to changing the gadget framework, so let > me take a look at your suggestion to see how it turns out. > Hi Felipe, Instead of catching the out of FIFO memory issue during the ep enable stage, I was thinking if we could do it somewhere during the bind. Then this would allow for at least failing the bind instead of having an enumerated device which doesn't work. (will happen if we bail out during ep enable phase) The idea I had was the following: Introduce a new USB gadget function pointer, say usb_gadget_check_config(struct usb_gadget *gadget, unsigned long ep_map) The purpose for the ep_map is to carry information about the endpoints the configuration requires, since each function driver will define the endpoint descriptor(s) it will advertise to the host. We have access to these ep desc after the bind() routine is executed for the function driver, so we can update this map after every bind. The configfs driver will call the check config API every time a configuration is added. static int configfs_composite_bind(struct usb_gadget *gadget, struct usb_gadget_driver *gdriver) { ... /* Go through all configs, attach all functions */ list_for_each_entry(c, &gi->cdev.configs, list) { ... list_for_each_entry_safe(f, tmp, &cfg->func_list, list) { ... if (f->ss_descriptors) { struct usb_descriptor_header **descriptors; descriptors = f->ss_descriptors; for (; *descriptors; ++descriptors) { struct usb_endpoint_descriptor *ep; int addr; if ((*descriptors)->bDescriptorType != USB_DT_ENDPOINT) continue; ep = (struct usb_endpoint_descriptor *)*descriptors; addr = ((ep->bEndpointAddress & 0x80) >> 3) | (ep->bEndpointAddress & 0x0f); set_bit(addr, &ep_map); } } usb_gadget_check_config(cdev->gadget, ep_map); What it'll allow us to do is to decode the ep_map in the dwc3/udc driver to determine if we have enough fifo space. Also, if we wanted to utilize this ep map for the actual resizing stage, we could eliminate the issue of not knowing how many EPs will be enabled, and allocating potentially unused fifos due to unused eps. Thanks Wesley -- The Qualcomm Innovation Center, Inc. is a member of the Code Aurora Forum, a Linux Foundation Collaborative Project ^ permalink raw reply [flat|nested] 13+ messages in thread
* Re: [RFC v4 1/3] usb: dwc3: Resize TX FIFOs to meet EP bursting requirements 2020-06-24 2:28 ` [RFC v4 1/3] usb: dwc3: Resize TX FIFOs to meet EP bursting requirements Wesley Cheng 2020-08-10 12:27 ` Felipe Balbi @ 2020-08-12 2:22 ` Peter Chen 2020-08-12 7:00 ` Wesley Cheng 1 sibling, 1 reply; 13+ messages in thread From: Peter Chen @ 2020-08-12 2:22 UTC (permalink / raw) To: Wesley Cheng Cc: agross, bjorn.andersson, balbi, Greg Kroah-Hartman, robh+dt, lkml, devicetree, linux-arm-msm, USB list, jackp On Wed, Jun 24, 2020 at 10:31 AM Wesley Cheng <wcheng@codeaurora.org> wrote: > > Some devices have USB compositions which may require multiple endpoints > that support EP bursting. HW defined TX FIFO sizes may not always be > sufficient for these compositions. By utilizing flexible TX FIFO > allocation, this allows for endpoints to request the required FIFO depth to > achieve higher bandwidth. With some higher bMaxBurst configurations, using > a larger TX FIFO size results in better TX throughput. > > Ensure that one TX FIFO is reserved for every IN endpoint. This allows for > the FIFO logic to prevent running out of FIFO space. > You may do this for only allocated endpoints, but you need override default .match_ep API. See cdns3/gadget.c and cdns3/ep0.c as an example. Peter > Signed-off-by: Wesley Cheng <wcheng@codeaurora.org> > --- > drivers/usb/dwc3/core.c | 2 + > drivers/usb/dwc3/core.h | 8 +++ > drivers/usb/dwc3/ep0.c | 37 +++++++++++- > drivers/usb/dwc3/gadget.c | 115 ++++++++++++++++++++++++++++++++++++++ > 4 files changed, 161 insertions(+), 1 deletion(-) > > diff --git a/drivers/usb/dwc3/core.c b/drivers/usb/dwc3/core.c > index edc17155cb2b..cca555493929 100644 > --- a/drivers/usb/dwc3/core.c > +++ b/drivers/usb/dwc3/core.c > @@ -1304,6 +1304,8 @@ static void dwc3_get_properties(struct dwc3 *dwc) > &tx_thr_num_pkt_prd); > device_property_read_u8(dev, "snps,tx-max-burst-prd", > &tx_max_burst_prd); > + dwc->needs_fifo_resize = device_property_read_bool(dev, > + "tx-fifo-resize"); > > dwc->disable_scramble_quirk = device_property_read_bool(dev, > "snps,disable_scramble_quirk"); > diff --git a/drivers/usb/dwc3/core.h b/drivers/usb/dwc3/core.h > index 4c171a8e215f..ce0bf288b6ac 100644 > --- a/drivers/usb/dwc3/core.h > +++ b/drivers/usb/dwc3/core.h > @@ -675,6 +675,7 @@ struct dwc3_event_buffer { > * isochronous START TRANSFER command failure workaround > * @start_cmd_status: the status of testing START TRANSFER command with > * combo_num = 'b00 > + * @fifo_depth: allocated TXFIFO depth > */ > struct dwc3_ep { > struct usb_ep endpoint; > @@ -727,6 +728,7 @@ struct dwc3_ep { > /* For isochronous START TRANSFER workaround only */ > u8 combo_num; > int start_cmd_status; > + int fifo_depth; > }; > > enum dwc3_phy { > @@ -1004,6 +1006,7 @@ struct dwc3_scratchpad_array { > * 1 - utmi_l1_suspend_n > * @is_fpga: true when we are using the FPGA board > * @pending_events: true when we have pending IRQs to be handled > + * @needs_fifo_resize: not all users might want fifo resizing, flag it > * @pullups_connected: true when Run/Stop bit is set > * @setup_packet_pending: true when there's a Setup Packet in FIFO. Workaround > * @three_stage_setup: set if we perform a three phase setup > @@ -1044,6 +1047,8 @@ struct dwc3_scratchpad_array { > * @dis_metastability_quirk: set to disable metastability quirk. > * @imod_interval: set the interrupt moderation interval in 250ns > * increments or 0 to disable. > + * @last_fifo_depth: total TXFIFO depth of all enabled USB IN/INT endpoints > + * @num_ep_resized: the number of TX FIFOs that have already been resized > */ > struct dwc3 { > struct work_struct drd_work; > @@ -1204,6 +1209,7 @@ struct dwc3 { > unsigned is_utmi_l1_suspend:1; > unsigned is_fpga:1; > unsigned pending_events:1; > + unsigned needs_fifo_resize:1; > unsigned pullups_connected:1; > unsigned setup_packet_pending:1; > unsigned three_stage_setup:1; > @@ -1236,6 +1242,8 @@ struct dwc3 { > unsigned dis_metastability_quirk:1; > > u16 imod_interval; > + int last_fifo_depth; > + int num_ep_resized; > }; > > #define INCRX_BURST_MODE 0 > diff --git a/drivers/usb/dwc3/ep0.c b/drivers/usb/dwc3/ep0.c > index 6dee4dabc0a4..76db9b530861 100644 > --- a/drivers/usb/dwc3/ep0.c > +++ b/drivers/usb/dwc3/ep0.c > @@ -601,8 +601,9 @@ static int dwc3_ep0_set_config(struct dwc3 *dwc, struct usb_ctrlrequest *ctrl) > { > enum usb_device_state state = dwc->gadget.state; > u32 cfg; > - int ret; > + int ret, num, size; > u32 reg; > + struct dwc3_ep *dep; > > cfg = le16_to_cpu(ctrl->wValue); > > @@ -611,6 +612,40 @@ static int dwc3_ep0_set_config(struct dwc3 *dwc, struct usb_ctrlrequest *ctrl) > return -EINVAL; > > case USB_STATE_ADDRESS: > + /* > + * If tx-fifo-resize flag is not set for the controller, then > + * do not clear existing allocated TXFIFO since we do not > + * allocate it again in dwc3_gadget_resize_tx_fifos > + */ > + if (dwc->needs_fifo_resize) { > + /* Read ep0IN related TXFIFO size */ > + dep = dwc->eps[1]; > + size = dwc3_readl(dwc->regs, DWC3_GTXFIFOSIZ(0)); > + if (dwc3_is_usb31(dwc)) > + dep->fifo_depth = DWC31_GTXFIFOSIZ_TXFDEP(size); > + else > + dep->fifo_depth = DWC3_GTXFIFOSIZ_TXFDEP(size); > + > + dwc->last_fifo_depth = dep->fifo_depth; > + /* Clear existing TXFIFO for all IN eps except ep0 */ > + for (num = 3; num < min_t(int, dwc->num_eps, > + DWC3_ENDPOINTS_NUM); num += 2) { > + dep = dwc->eps[num]; > + /* Don't change TXFRAMNUM on usb31 version */ > + size = dwc3_is_usb31(dwc) ? > + dwc3_readl(dwc->regs, > + DWC3_GTXFIFOSIZ(num >> 1)) & > + DWC31_GTXFIFOSIZ_TXFRAMNUM : > + 0; > + > + dwc3_writel(dwc->regs, > + DWC3_GTXFIFOSIZ(num >> 1), > + size); > + dep->fifo_depth = 0; > + } > + dwc->num_ep_resized = 0; > + } > + > ret = dwc3_ep0_delegate_req(dwc, ctrl); > /* if the cfg matches and the cfg is non zero */ > if (cfg && (!ret || (ret == USB_GADGET_DELAYED_STATUS))) { > diff --git a/drivers/usb/dwc3/gadget.c b/drivers/usb/dwc3/gadget.c > index 00746c2848c0..777badf3e85d 100644 > --- a/drivers/usb/dwc3/gadget.c > +++ b/drivers/usb/dwc3/gadget.c > @@ -540,6 +540,117 @@ static int dwc3_gadget_start_config(struct dwc3_ep *dep) > return 0; > } > > +/* > + * dwc3_gadget_resize_tx_fifos - reallocate fifo spaces for current use-case > + * @dwc: pointer to our context structure > + * > + * This function will a best effort FIFO allocation in order > + * to improve FIFO usage and throughput, while still allowing > + * us to enable as many endpoints as possible. > + * > + * Keep in mind that this operation will be highly dependent > + * on the configured size for RAM1 - which contains TxFifo -, > + * the amount of endpoints enabled on coreConsultant tool, and > + * the width of the Master Bus. > + * > + * In general, FIFO depths are represented with the following equation: > + * > + * fifo_size = mult * ((max_packet + mdwidth)/mdwidth + 1) + 1 > + * > + * Conversions can be done to the equation to derive the number of packets that > + * will fit to a particular FIFO size value. > + */ > +static int dwc3_gadget_resize_tx_fifos(struct dwc3_ep *dep) > +{ > + struct dwc3 *dwc = dep->dwc; > + int ram1_depth, mdwidth, fifo_0_start, tmp, num_in_ep; > + int min_depth, remaining, fifo_size, mult = 1, fifo, max_packet = 1024; > + > + if (!dwc->needs_fifo_resize) > + return 0; > + > + /* resize IN endpoints except ep0 */ > + if (!usb_endpoint_dir_in(dep->endpoint.desc) || dep->number <= 1) > + return 0; > + > + /* Don't resize already resized IN endpoint */ > + if (dep->fifo_depth) > + return 0; > + > + ram1_depth = DWC3_RAM1_DEPTH(dwc->hwparams.hwparams7); > + mdwidth = DWC3_MDWIDTH(dwc->hwparams.hwparams0); > + /* MDWIDTH is represented in bits, we need it in bytes */ > + mdwidth >>= 3; > + > + if (((dep->endpoint.maxburst > 1) && > + usb_endpoint_xfer_bulk(dep->endpoint.desc)) > + || usb_endpoint_xfer_isoc(dep->endpoint.desc)) > + mult = 3; > + > + if ((dep->endpoint.maxburst > 6) && > + usb_endpoint_xfer_bulk(dep->endpoint.desc) > + && dwc3_is_usb31(dwc)) > + mult = 6; > + > + /* FIFO size for a single buffer */ > + fifo = (max_packet + mdwidth)/mdwidth; > + fifo++; > + > + /* Calculate the number of remaining EPs w/o any FIFO */ > + num_in_ep = dwc->num_eps/2; > + num_in_ep -= dwc->num_ep_resized; > + /* Ignore EP0 IN */ > + num_in_ep--; > + > + /* Reserve at least one FIFO for the number of IN EPs */ > + min_depth = num_in_ep * (fifo+1); > + remaining = ram1_depth - min_depth - dwc->last_fifo_depth; > + > + /* We've already reserved 1 FIFO per EP, so check what we can fit in > + * addition to it. If there is not enough remaining space, allocate > + * all the remaining space to the EP. > + */ > + fifo_size = (mult-1) * fifo; > + if (remaining < fifo_size) { > + if (remaining > 0) > + fifo_size = remaining; > + else > + fifo_size = 0; > + } > + > + fifo_size += fifo; > + fifo_size++; > + dep->fifo_depth = fifo_size; > + > + /* Check if TXFIFOs start at non-zero addr */ > + tmp = dwc3_readl(dwc->regs, DWC3_GTXFIFOSIZ(0)); > + fifo_0_start = DWC3_GTXFIFOSIZ_TXFSTADDR(tmp); > + > + fifo_size |= (fifo_0_start + (dwc->last_fifo_depth << 16)); > + if (dwc3_is_usb31(dwc)) > + dwc->last_fifo_depth += DWC31_GTXFIFOSIZ_TXFDEP(fifo_size); > + else > + dwc->last_fifo_depth += DWC3_GTXFIFOSIZ_TXFDEP(fifo_size); > + > + /* Check fifo size allocation doesn't exceed available RAM size. */ > + if (dwc->last_fifo_depth >= ram1_depth) { > + dev_err(dwc->dev, "Fifosize(%d) > RAM size(%d) %s depth:%d\n", > + (dwc->last_fifo_depth * mdwidth), ram1_depth, > + dep->endpoint.name, fifo_size); > + if (dwc3_is_usb31(dwc)) > + fifo_size = DWC31_GTXFIFOSIZ_TXFDEP(fifo_size); > + else > + fifo_size = DWC3_GTXFIFOSIZ_TXFDEP(fifo_size); > + dwc->last_fifo_depth -= fifo_size; > + dep->fifo_depth = 0; > + return -ENOMEM; > + } > + > + dwc3_writel(dwc->regs, DWC3_GTXFIFOSIZ(dep->number >> 1), fifo_size); > + dwc->num_ep_resized++; > + return 0; > +} > + > static int dwc3_gadget_set_ep_config(struct dwc3_ep *dep, unsigned int action) > { > const struct usb_ss_ep_comp_descriptor *comp_desc; > @@ -620,6 +731,10 @@ static int __dwc3_gadget_ep_enable(struct dwc3_ep *dep, unsigned int action) > int ret; > > if (!(dep->flags & DWC3_EP_ENABLED)) { > + ret = dwc3_gadget_resize_tx_fifos(dep); > + if (ret) > + return ret; > + > ret = dwc3_gadget_start_config(dep); > if (ret) > return ret; > -- > The Qualcomm Innovation Center, Inc. is a member of the Code Aurora Forum, > a Linux Foundation Collaborative Project > ^ permalink raw reply [flat|nested] 13+ messages in thread
* Re: [RFC v4 1/3] usb: dwc3: Resize TX FIFOs to meet EP bursting requirements 2020-08-12 2:22 ` Peter Chen @ 2020-08-12 7:00 ` Wesley Cheng 2020-08-12 11:01 ` Peter Chen 0 siblings, 1 reply; 13+ messages in thread From: Wesley Cheng @ 2020-08-12 7:00 UTC (permalink / raw) To: Peter Chen Cc: agross, bjorn.andersson, balbi, Greg Kroah-Hartman, robh+dt, lkml, devicetree, linux-arm-msm, USB list, jackp On 8/11/2020 7:22 PM, Peter Chen wrote: > On Wed, Jun 24, 2020 at 10:31 AM Wesley Cheng <wcheng@codeaurora.org> wrote: >> >> Some devices have USB compositions which may require multiple endpoints >> that support EP bursting. HW defined TX FIFO sizes may not always be >> sufficient for these compositions. By utilizing flexible TX FIFO >> allocation, this allows for endpoints to request the required FIFO depth to >> achieve higher bandwidth. With some higher bMaxBurst configurations, using >> a larger TX FIFO size results in better TX throughput. >> >> Ensure that one TX FIFO is reserved for every IN endpoint. This allows for >> the FIFO logic to prevent running out of FIFO space. >> > > You may do this for only allocated endpoints, but you need override > default .match_ep > API. See cdns3/gadget.c and cdns3/ep0.c as an example. > > Peter > Hi Peter, Thank you for your input. I've actually considered doing some matching/resizing in the .match_ep route as well, but it doesn't work well for situations where multiple configurations are in play. The reason being that if you look at the epautoconf APIs, the configfs driver will use the usb_ep_autoconfig_reset() to reset the endpoints claimed between initialization of each configuration. This means that the epautoconf driver expects to re-use the usb_endpoints: static int configfs_composite_bind(struct usb_gadget *gadget, struct usb_gadget_driver *gdriver) { ... /* Go through all configs, attach all functions */ list_for_each_entry(c, &gi->cdev.configs, list) { ... list_for_each_entry_safe(f, tmp, &cfg->func_list, list) { list_del(&f->list); ret = usb_add_function(c, f); if (ret) { list_add(&f->list, &cfg->func_list); goto err_purge_funcs; } } usb_ep_autoconfig_reset(cdev->gadget); } So in this situation, I wouldn't want the dwc3 gadget driver to assign a different dwc3 ep for endpoints in each configuration, when we know that only one set of EPs will be active when the host chooses. I hope I understood your feedback correctly, and definitely appreciate the input! Thanks Wesley -- The Qualcomm Innovation Center, Inc. is a member of the Code Aurora Forum, a Linux Foundation Collaborative Project ^ permalink raw reply [flat|nested] 13+ messages in thread
* RE: [RFC v4 1/3] usb: dwc3: Resize TX FIFOs to meet EP bursting requirements 2020-08-12 7:00 ` Wesley Cheng @ 2020-08-12 11:01 ` Peter Chen 0 siblings, 0 replies; 13+ messages in thread From: Peter Chen @ 2020-08-12 11:01 UTC (permalink / raw) To: Wesley Cheng, Peter Chen Cc: agross, bjorn.andersson, balbi, Greg Kroah-Hartman, robh+dt, lkml, devicetree, linux-arm-msm, USB list, jackp > > Thank you for your input. I've actually considered doing some matching/resizing in > the .match_ep route as well, but it doesn't work well for situations where multiple > configurations are in play. The reason being that if you look at the epautoconf APIs, > the configfs driver will use the usb_ep_autoconfig_reset() to reset the endpoints > claimed between initialization of each configuration. This means that the > epautoconf driver expects to re-use the usb_endpoints: > > static int configfs_composite_bind(struct usb_gadget *gadget, > struct usb_gadget_driver *gdriver) > { > ... > > /* Go through all configs, attach all functions */ list_for_each_entry(c, &gi- > >cdev.configs, list) { ... > list_for_each_entry_safe(f, tmp, &cfg->func_list, list) { > list_del(&f->list); > ret = usb_add_function(c, f); > if (ret) { > list_add(&f->list, &cfg->func_list); > goto err_purge_funcs; > } > } > usb_ep_autoconfig_reset(cdev->gadget); > } > > So in this situation, I wouldn't want the dwc3 gadget driver to assign a different > dwc3 ep for endpoints in each configuration, when we know that only one set of > EPs will be active when the host chooses. I hope I understood your feedback > correctly, and definitely appreciate the input! > Thanks for mention that, we didn't consider multiple configurations use case, it needs the UDC driver to record the configuration information, it is too complex at current framework. I think your solution is OK, reserving one packet for each IN endpoint to avoid running out of FIFO for later endpoints and fit the first endpoints with larger FIFO room to get the best performance, it could use as many as FIFOs the device owns. Peter ^ permalink raw reply [flat|nested] 13+ messages in thread
* [RFC v4 2/3] arm64: boot: dts: qcom: sm8150: Enable dynamic TX FIFO resize logic 2020-06-24 2:28 [RFC v4 0/3] Re-introduce TX FIFO resize for larger EP bursting Wesley Cheng 2020-06-24 2:28 ` [RFC v4 1/3] usb: dwc3: Resize TX FIFOs to meet EP bursting requirements Wesley Cheng @ 2020-06-24 2:28 ` Wesley Cheng 2020-06-24 2:28 ` [RFC v4 3/3] dt-bindings: usb: dwc3: Add entry for tx-fifo-resize Wesley Cheng 2 siblings, 0 replies; 13+ messages in thread From: Wesley Cheng @ 2020-06-24 2:28 UTC (permalink / raw) To: agross, bjorn.andersson, balbi, gregkh, robh+dt Cc: linux-kernel, devicetree, linux-arm-msm, linux-usb, jackp, Wesley Cheng Enable the flexible TX FIFO resize logic on SM8150. Using a larger TX FIFO SZ can help account for situations when system latency is greater than the USB bus transmission latency. Signed-off-by: Wesley Cheng <wcheng@codeaurora.org> --- arch/arm64/boot/dts/qcom/sm8150.dtsi | 1 + 1 file changed, 1 insertion(+) diff --git a/arch/arm64/boot/dts/qcom/sm8150.dtsi b/arch/arm64/boot/dts/qcom/sm8150.dtsi index a36512d1f6a1..c28523313955 100644 --- a/arch/arm64/boot/dts/qcom/sm8150.dtsi +++ b/arch/arm64/boot/dts/qcom/sm8150.dtsi @@ -708,6 +708,7 @@ usb_1_dwc3: dwc3@a600000 { interrupts = <GIC_SPI 133 IRQ_TYPE_LEVEL_HIGH>; snps,dis_u2_susphy_quirk; snps,dis_enblslpm_quirk; + tx-fifo-resize; phys = <&usb_1_hsphy>, <&usb_1_ssphy>; phy-names = "usb2-phy", "usb3-phy"; }; -- The Qualcomm Innovation Center, Inc. is a member of the Code Aurora Forum, a Linux Foundation Collaborative Project ^ permalink raw reply related [flat|nested] 13+ messages in thread
* [RFC v4 3/3] dt-bindings: usb: dwc3: Add entry for tx-fifo-resize 2020-06-24 2:28 [RFC v4 0/3] Re-introduce TX FIFO resize for larger EP bursting Wesley Cheng 2020-06-24 2:28 ` [RFC v4 1/3] usb: dwc3: Resize TX FIFOs to meet EP bursting requirements Wesley Cheng 2020-06-24 2:28 ` [RFC v4 2/3] arm64: boot: dts: qcom: sm8150: Enable dynamic TX FIFO resize logic Wesley Cheng @ 2020-06-24 2:28 ` Wesley Cheng 2 siblings, 0 replies; 13+ messages in thread From: Wesley Cheng @ 2020-06-24 2:28 UTC (permalink / raw) To: agross, bjorn.andersson, balbi, gregkh, robh+dt Cc: linux-kernel, devicetree, linux-arm-msm, linux-usb, jackp, Wesley Cheng, Rob Herring Re-introduce the comment for the tx-fifo-resize setting for the DWC3 controller. This allows for vendors to control if they require the TX FIFO resizing logic on their HW, as the default FIFO size configurations may already be sufficient. Signed-off-by: Wesley Cheng <wcheng@codeaurora.org> Acked-by: Rob Herring <robh@kernel.org> --- Documentation/devicetree/bindings/usb/dwc3.txt | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) diff --git a/Documentation/devicetree/bindings/usb/dwc3.txt b/Documentation/devicetree/bindings/usb/dwc3.txt index 9946ff9ba735..489f5da83744 100644 --- a/Documentation/devicetree/bindings/usb/dwc3.txt +++ b/Documentation/devicetree/bindings/usb/dwc3.txt @@ -105,7 +105,7 @@ Optional properties: 1-16 (DWC_usb31 programming guide section 1.2.3) to enable periodic ESS TX threshold. - - <DEPRECATED> tx-fifo-resize: determines if the FIFO *has* to be reallocated. + - tx-fifo-resize: determines if the FIFO *has* to be reallocated. - snps,incr-burst-type-adjustment: Value for INCR burst type of GSBUSCFG0 register, undefined length INCR burst type enable and INCRx type. When just one value, which means INCRX burst mode enabled. When -- The Qualcomm Innovation Center, Inc. is a member of the Code Aurora Forum, a Linux Foundation Collaborative Project ^ permalink raw reply related [flat|nested] 13+ messages in thread
end of thread, other threads:[~2020-08-18 19:59 UTC | newest] Thread overview: 13+ messages (download: mbox.gz / follow: Atom feed) -- links below jump to the message on this page -- 2020-06-24 2:28 [RFC v4 0/3] Re-introduce TX FIFO resize for larger EP bursting Wesley Cheng 2020-06-24 2:28 ` [RFC v4 1/3] usb: dwc3: Resize TX FIFOs to meet EP bursting requirements Wesley Cheng 2020-08-10 12:27 ` Felipe Balbi 2020-08-11 5:10 ` Wesley Cheng 2020-08-11 7:12 ` Felipe Balbi 2020-08-11 13:44 ` Alan Stern 2020-08-12 18:34 ` Wesley Cheng 2020-08-18 19:58 ` Wesley Cheng 2020-08-12 2:22 ` Peter Chen 2020-08-12 7:00 ` Wesley Cheng 2020-08-12 11:01 ` Peter Chen 2020-06-24 2:28 ` [RFC v4 2/3] arm64: boot: dts: qcom: sm8150: Enable dynamic TX FIFO resize logic Wesley Cheng 2020-06-24 2:28 ` [RFC v4 3/3] dt-bindings: usb: dwc3: Add entry for tx-fifo-resize Wesley Cheng
This is a public inbox, see mirroring instructions for how to clone and mirror all data and code used for this inbox; as well as URLs for NNTP newsgroup(s).