[PATCH V2 0/2] brcmstb: initial work on BCM4908

[PATCH V2 0/2] brcmstb: initial work on BCM4908

[Rafał Miłecki]

From: Rafał Miłecki <rafal@milecki.pl>

BCM4908 uses very similar hardware to the STB one. It still requires
some tweaks but this initial work allows accessing hardware without:

Internal error: synchronous external abort: 96000210 [#1] PREEMPT SMP                                                                                                                                                                                                          

Rafał Miłecki (2):
  dt-bindings: PCI: brcmstb: add BCM4908 binding
  PCI: brcmstb: support BCM4908 with external PERST# signal controller

 .../bindings/pci/brcm,stb-pcie.yaml           | 30 +++++++++++++++--
 drivers/pci/controller/Kconfig                |  2 +-
 drivers/pci/controller/pcie-brcmstb.c         | 32 +++++++++++++++++++
 3 files changed, 61 insertions(+), 3 deletions(-)

-- 
2.26.2

[PATCH V2 1/2] dt-bindings: PCI: brcmstb: add BCM4908 binding

[Rafał Miłecki]

From: Rafał Miłecki <rafal@milecki.pl>

BCM4908 is a SoC family with PCIe controller sharing design with the one
for STB. BCM4908 has different power management and memory controller so
few tweaks are required.

PERST# signal on BCM4908 is handled by an external MISC block so it
needs specifying a reset phandle.

Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
---
 .../bindings/pci/brcm,stb-pcie.yaml           | 30 +++++++++++++++++--
 1 file changed, 28 insertions(+), 2 deletions(-)

diff --git a/Documentation/devicetree/bindings/pci/brcm,stb-pcie.yaml b/Documentation/devicetree/bindings/pci/brcm,stb-pcie.yaml
index 807694b4f41f..d3ab9e22f97c 100644
--- a/Documentation/devicetree/bindings/pci/brcm,stb-pcie.yaml
+++ b/Documentation/devicetree/bindings/pci/brcm,stb-pcie.yaml
@@ -14,6 +14,7 @@ properties:
     items:
       - enum:
           - brcm,bcm2711-pcie # The Raspberry Pi 4
+          - brcm,bcm4908-pcie
           - brcm,bcm7211-pcie # Broadcom STB version of RPi4
           - brcm,bcm7278-pcie # Broadcom 7278 Arm
           - brcm,bcm7216-pcie # Broadcom 7216 Arm
@@ -64,8 +65,6 @@ properties:
   aspm-no-l0s: true
 
   resets:
-    description: for "brcm,bcm7216-pcie", must be a valid reset
-      phandle pointing to the RESCAL reset controller provider node.
     $ref: "/schemas/types.yaml#/definitions/phandle"
 
   reset-names:
@@ -98,12 +97,39 @@ required:
 
 allOf:
   - $ref: /schemas/pci/pci-bus.yaml#
+  - if:
+      properties:
+        compatible:
+          contains:
+            const: brcm,bcm4908-pcie
+    then:
+      properties:
+        resets:
+          items:
+            - description: reset controller handling the PERST# signal
+
+        reset-names:
+          items:
+            - const: perst
+
+      required:
+        - resets
+        - reset-names
   - if:
       properties:
         compatible:
           contains:
             const: brcm,bcm7216-pcie
     then:
+      properties:
+        resets:
+          items:
+            - description: phandle pointing to the RESCAL reset controller
+
+        reset-names:
+          items:
+            - const: rescal
+
       required:
         - resets
         - reset-names
-- 
2.26.2

[PATCH V2 2/2] PCI: brcmstb: support BCM4908 with external PERST# signal controller

[Rafał Miłecki]

From: Rafał Miłecki <rafal@milecki.pl>

BCM4908 uses external MISC block for controlling PERST# signal. Use it
as a reset controller.

Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
---
V2: Reorder BCM4908 in the enum pcie_type
    Use devm_reset_control_get_optional_exclusive()
    Don't move hw_rev read up in the code
---
 drivers/pci/controller/Kconfig        |  2 +-
 drivers/pci/controller/pcie-brcmstb.c | 32 +++++++++++++++++++++++++++
 2 files changed, 33 insertions(+), 1 deletion(-)

diff --git a/drivers/pci/controller/Kconfig b/drivers/pci/controller/Kconfig
index 64e2f5e379aa..d44c70bb88f6 100644
--- a/drivers/pci/controller/Kconfig
+++ b/drivers/pci/controller/Kconfig
@@ -273,7 +273,7 @@ config VMD
 
 config PCIE_BRCMSTB
 	tristate "Broadcom Brcmstb PCIe host controller"
-	depends on ARCH_BRCMSTB || ARCH_BCM2835 || COMPILE_TEST
+	depends on ARCH_BRCMSTB || ARCH_BCM2835 || ARCH_BCM4908 || COMPILE_TEST
 	depends on OF
 	depends on PCI_MSI_IRQ_DOMAIN
 	default ARCH_BRCMSTB
diff --git a/drivers/pci/controller/pcie-brcmstb.c b/drivers/pci/controller/pcie-brcmstb.c
index 9c3d2982248d..98536cf3af58 100644
--- a/drivers/pci/controller/pcie-brcmstb.c
+++ b/drivers/pci/controller/pcie-brcmstb.c
@@ -96,6 +96,7 @@
 
 #define PCIE_MISC_REVISION				0x406c
 #define  BRCM_PCIE_HW_REV_33				0x0303
+#define  BRCM_PCIE_HW_REV_3_20				0x0320
 
 #define PCIE_MISC_CPU_2_PCIE_MEM_WIN0_BASE_LIMIT		0x4070
 #define  PCIE_MISC_CPU_2_PCIE_MEM_WIN0_BASE_LIMIT_LIMIT_MASK	0xfff00000
@@ -190,6 +191,7 @@
 struct brcm_pcie;
 static inline void brcm_pcie_bridge_sw_init_set_7278(struct brcm_pcie *pcie, u32 val);
 static inline void brcm_pcie_bridge_sw_init_set_generic(struct brcm_pcie *pcie, u32 val);
+static inline void brcm_pcie_perst_set_4908(struct brcm_pcie *pcie, u32 val);
 static inline void brcm_pcie_perst_set_7278(struct brcm_pcie *pcie, u32 val);
 static inline void brcm_pcie_perst_set_generic(struct brcm_pcie *pcie, u32 val);
 
@@ -206,6 +208,7 @@ enum {
 
 enum pcie_type {
 	GENERIC,
+	BCM4908,
 	BCM7278,
 	BCM2711,
 };
@@ -230,6 +233,13 @@ static const struct pcie_cfg_data generic_cfg = {
 	.bridge_sw_init_set = brcm_pcie_bridge_sw_init_set_generic,
 };
 
+static const struct pcie_cfg_data bcm4908_cfg = {
+	.offsets	= pcie_offsets,
+	.type		= BCM4908,
+	.perst_set	= brcm_pcie_perst_set_4908,
+	.bridge_sw_init_set = brcm_pcie_bridge_sw_init_set_generic,
+};
+
 static const int pcie_offset_bcm7278[] = {
 	[RGR1_SW_INIT_1] = 0xc010,
 	[EXT_CFG_INDEX] = 0x9000,
@@ -282,6 +292,7 @@ struct brcm_pcie {
 	const int		*reg_offsets;
 	enum pcie_type		type;
 	struct reset_control	*rescal;
+	struct reset_control	*perst_reset;
 	int			num_memc;
 	u64			memc_size[PCIE_BRCM_MAX_MEMC];
 	u32			hw_rev;
@@ -747,6 +758,17 @@ static inline void brcm_pcie_bridge_sw_init_set_7278(struct brcm_pcie *pcie, u32
 	writel(tmp, pcie->base + PCIE_RGR1_SW_INIT_1(pcie));
 }
 
+static inline void brcm_pcie_perst_set_4908(struct brcm_pcie *pcie, u32 val)
+{
+	if (WARN_ONCE(!pcie->perst_reset, "missing PERST# reset controller\n"))
+		return;
+
+	if (val)
+		reset_control_assert(pcie->perst_reset);
+	else
+		reset_control_deassert(pcie->perst_reset);
+}
+
 static inline void brcm_pcie_perst_set_7278(struct brcm_pcie *pcie, u32 val)
 {
 	u32 tmp;
@@ -1206,6 +1228,7 @@ static int brcm_pcie_remove(struct platform_device *pdev)
 
 static const struct of_device_id brcm_pcie_match[] = {
 	{ .compatible = "brcm,bcm2711-pcie", .data = &bcm2711_cfg },
+	{ .compatible = "brcm,bcm4908-pcie", .data = &bcm4908_cfg },
 	{ .compatible = "brcm,bcm7211-pcie", .data = &generic_cfg },
 	{ .compatible = "brcm,bcm7278-pcie", .data = &bcm7278_cfg },
 	{ .compatible = "brcm,bcm7216-pcie", .data = &bcm7278_cfg },
@@ -1262,6 +1285,11 @@ static int brcm_pcie_probe(struct platform_device *pdev)
 		clk_disable_unprepare(pcie->clk);
 		return PTR_ERR(pcie->rescal);
 	}
+	pcie->perst_reset = devm_reset_control_get_optional_exclusive(&pdev->dev, "perst");
+	if (IS_ERR(pcie->perst_reset)) {
+		clk_disable_unprepare(pcie->clk);
+		return PTR_ERR(pcie->perst_reset);
+	}
 
 	ret = reset_control_deassert(pcie->rescal);
 	if (ret)
@@ -1279,6 +1307,10 @@ static int brcm_pcie_probe(struct platform_device *pdev)
 		goto fail;
 
 	pcie->hw_rev = readl(pcie->base + PCIE_MISC_REVISION);
+	if (pcie->type == BCM4908 && pcie->hw_rev >= BRCM_PCIE_HW_REV_3_20) {
+		dev_err(pcie->dev, "hardware revision with unsupported PERST# setup\n");
+		goto fail;
+	}
 
 	msi_np = of_parse_phandle(pcie->np, "msi-parent", 0);
 	if (pci_msi_enabled() && msi_np == pcie->np) {
-- 
2.26.2

Re: [PATCH V2 2/2] PCI: brcmstb: support BCM4908 with external PERST# signal controller

[Florian Fainelli]

On 11/30/2020 12:32 AM, Rafał Miłecki wrote:
> From: Rafał Miłecki <rafal@milecki.pl>
> 
> BCM4908 uses external MISC block for controlling PERST# signal. Use it
> as a reset controller.
> 
> Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
> ---
> V2: Reorder BCM4908 in the enum pcie_type
>     Use devm_reset_control_get_optional_exclusive()
>     Don't move hw_rev read up in the code
> ---
>  drivers/pci/controller/Kconfig        |  2 +-
>  drivers/pci/controller/pcie-brcmstb.c | 32 +++++++++++++++++++++++++++
>  2 files changed, 33 insertions(+), 1 deletion(-)
> 
> diff --git a/drivers/pci/controller/Kconfig b/drivers/pci/controller/Kconfig
> index 64e2f5e379aa..d44c70bb88f6 100644
> --- a/drivers/pci/controller/Kconfig
> +++ b/drivers/pci/controller/Kconfig
> @@ -273,7 +273,7 @@ config VMD
>  
>  config PCIE_BRCMSTB
>  	tristate "Broadcom Brcmstb PCIe host controller"
> -	depends on ARCH_BRCMSTB || ARCH_BCM2835 || COMPILE_TEST
> +	depends on ARCH_BRCMSTB || ARCH_BCM2835 || ARCH_BCM4908 || COMPILE_TEST
>  	depends on OF
>  	depends on PCI_MSI_IRQ_DOMAIN
>  	default ARCH_BRCMSTB
> diff --git a/drivers/pci/controller/pcie-brcmstb.c b/drivers/pci/controller/pcie-brcmstb.c
> index 9c3d2982248d..98536cf3af58 100644
> --- a/drivers/pci/controller/pcie-brcmstb.c
> +++ b/drivers/pci/controller/pcie-brcmstb.c
> @@ -96,6 +96,7 @@
>  
>  #define PCIE_MISC_REVISION				0x406c
>  #define  BRCM_PCIE_HW_REV_33				0x0303
> +#define  BRCM_PCIE_HW_REV_3_20				0x0320
>  
>  #define PCIE_MISC_CPU_2_PCIE_MEM_WIN0_BASE_LIMIT		0x4070
>  #define  PCIE_MISC_CPU_2_PCIE_MEM_WIN0_BASE_LIMIT_LIMIT_MASK	0xfff00000
> @@ -190,6 +191,7 @@
>  struct brcm_pcie;
>  static inline void brcm_pcie_bridge_sw_init_set_7278(struct brcm_pcie *pcie, u32 val);
>  static inline void brcm_pcie_bridge_sw_init_set_generic(struct brcm_pcie *pcie, u32 val);
> +static inline void brcm_pcie_perst_set_4908(struct brcm_pcie *pcie, u32 val);
>  static inline void brcm_pcie_perst_set_7278(struct brcm_pcie *pcie, u32 val);
>  static inline void brcm_pcie_perst_set_generic(struct brcm_pcie *pcie, u32 val);
>  
> @@ -206,6 +208,7 @@ enum {
>  
>  enum pcie_type {
>  	GENERIC,
> +	BCM4908,
>  	BCM7278,
>  	BCM2711,
>  };
> @@ -230,6 +233,13 @@ static const struct pcie_cfg_data generic_cfg = {
>  	.bridge_sw_init_set = brcm_pcie_bridge_sw_init_set_generic,
>  };
>  
> +static const struct pcie_cfg_data bcm4908_cfg = {
> +	.offsets	= pcie_offsets,
> +	.type		= BCM4908,
> +	.perst_set	= brcm_pcie_perst_set_4908,
> +	.bridge_sw_init_set = brcm_pcie_bridge_sw_init_set_generic,
> +};
> +
>  static const int pcie_offset_bcm7278[] = {
>  	[RGR1_SW_INIT_1] = 0xc010,
>  	[EXT_CFG_INDEX] = 0x9000,
> @@ -282,6 +292,7 @@ struct brcm_pcie {
>  	const int		*reg_offsets;
>  	enum pcie_type		type;
>  	struct reset_control	*rescal;
> +	struct reset_control	*perst_reset;
>  	int			num_memc;
>  	u64			memc_size[PCIE_BRCM_MAX_MEMC];
>  	u32			hw_rev;
> @@ -747,6 +758,17 @@ static inline void brcm_pcie_bridge_sw_init_set_7278(struct brcm_pcie *pcie, u32
>  	writel(tmp, pcie->base + PCIE_RGR1_SW_INIT_1(pcie));
>  }
>  
> +static inline void brcm_pcie_perst_set_4908(struct brcm_pcie *pcie, u32 val)
> +{
> +	if (WARN_ONCE(!pcie->perst_reset, "missing PERST# reset controller\n"))
> +		return;
> +
> +	if (val)
> +		reset_control_assert(pcie->perst_reset);
> +	else
> +		reset_control_deassert(pcie->perst_reset);

This looks good to me now, just one nit, you probably do not support
suspend/resume on the 4908, likely never will, but you should probably
pulse the PERST# during PCIe resume, too. With that fixed:

Acked-by: Florian Fainelli <f.fainelli@gmail.com>
-- 
Florian

Re: [PATCH V2 1/2] dt-bindings: PCI: brcmstb: add BCM4908 binding

[Rob Herring]

On Mon, Nov 30, 2020 at 09:32:22AM +0100, Rafał Miłecki wrote:
> From: Rafał Miłecki <rafal@milecki.pl>
> 
> BCM4908 is a SoC family with PCIe controller sharing design with the one
> for STB. BCM4908 has different power management and memory controller so
> few tweaks are required.
> 
> PERST# signal on BCM4908 is handled by an external MISC block so it
> needs specifying a reset phandle.
> 
> Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
> Acked-by: Florian Fainelli <f.fainelli@gmail.com>
> ---
>  .../bindings/pci/brcm,stb-pcie.yaml           | 30 +++++++++++++++++--
>  1 file changed, 28 insertions(+), 2 deletions(-)
> 
> diff --git a/Documentation/devicetree/bindings/pci/brcm,stb-pcie.yaml b/Documentation/devicetree/bindings/pci/brcm,stb-pcie.yaml
> index 807694b4f41f..d3ab9e22f97c 100644
> --- a/Documentation/devicetree/bindings/pci/brcm,stb-pcie.yaml
> +++ b/Documentation/devicetree/bindings/pci/brcm,stb-pcie.yaml
> @@ -14,6 +14,7 @@ properties:
>      items:
>        - enum:
>            - brcm,bcm2711-pcie # The Raspberry Pi 4
> +          - brcm,bcm4908-pcie
>            - brcm,bcm7211-pcie # Broadcom STB version of RPi4
>            - brcm,bcm7278-pcie # Broadcom 7278 Arm
>            - brcm,bcm7216-pcie # Broadcom 7216 Arm
> @@ -64,8 +65,6 @@ properties:
>    aspm-no-l0s: true
>  
>    resets:
> -    description: for "brcm,bcm7216-pcie", must be a valid reset
> -      phandle pointing to the RESCAL reset controller provider node.
>      $ref: "/schemas/types.yaml#/definitions/phandle"

This should really just be 'maxItems: 1'. 'resets' already has a type.

>  
>    reset-names:
> @@ -98,12 +97,39 @@ required:
>  
>  allOf:
>    - $ref: /schemas/pci/pci-bus.yaml#
> +  - if:
> +      properties:
> +        compatible:
> +          contains:
> +            const: brcm,bcm4908-pcie
> +    then:
> +      properties:
> +        resets:
> +          items:
> +            - description: reset controller handling the PERST# signal
> +
> +        reset-names:
> +          items:
> +            - const: perst
> +
> +      required:
> +        - resets
> +        - reset-names
>    - if:
>        properties:
>          compatible:
>            contains:
>              const: brcm,bcm7216-pcie
>      then:
> +      properties:
> +        resets:
> +          items:
> +            - description: phandle pointing to the RESCAL reset controller
> +
> +        reset-names:
> +          items:
> +            - const: rescal
> +
>        required:
>          - resets
>          - reset-names
> -- 
> 2.26.2
> 

Re: [PATCH V2 2/2] PCI: brcmstb: support BCM4908 with external PERST# signal controller

[Rafał Miłecki]

On 04.12.2020 19:21, Florian Fainelli wrote:
> On 11/30/2020 12:32 AM, Rafał Miłecki wrote:
>> From: Rafał Miłecki <rafal@milecki.pl>
>>
>> BCM4908 uses external MISC block for controlling PERST# signal. Use it
>> as a reset controller.
>>
>> Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
>> ---
>> V2: Reorder BCM4908 in the enum pcie_type
>>      Use devm_reset_control_get_optional_exclusive()
>>      Don't move hw_rev read up in the code
>> ---
>>   drivers/pci/controller/Kconfig        |  2 +-
>>   drivers/pci/controller/pcie-brcmstb.c | 32 +++++++++++++++++++++++++++
>>   2 files changed, 33 insertions(+), 1 deletion(-)
>>
>> diff --git a/drivers/pci/controller/Kconfig b/drivers/pci/controller/Kconfig
>> index 64e2f5e379aa..d44c70bb88f6 100644
>> --- a/drivers/pci/controller/Kconfig
>> +++ b/drivers/pci/controller/Kconfig
>> @@ -273,7 +273,7 @@ config VMD
>>   
>>   config PCIE_BRCMSTB
>>   	tristate "Broadcom Brcmstb PCIe host controller"
>> -	depends on ARCH_BRCMSTB || ARCH_BCM2835 || COMPILE_TEST
>> +	depends on ARCH_BRCMSTB || ARCH_BCM2835 || ARCH_BCM4908 || COMPILE_TEST
>>   	depends on OF
>>   	depends on PCI_MSI_IRQ_DOMAIN
>>   	default ARCH_BRCMSTB
>> diff --git a/drivers/pci/controller/pcie-brcmstb.c b/drivers/pci/controller/pcie-brcmstb.c
>> index 9c3d2982248d..98536cf3af58 100644
>> --- a/drivers/pci/controller/pcie-brcmstb.c
>> +++ b/drivers/pci/controller/pcie-brcmstb.c
>> @@ -96,6 +96,7 @@
>>   
>>   #define PCIE_MISC_REVISION				0x406c
>>   #define  BRCM_PCIE_HW_REV_33				0x0303
>> +#define  BRCM_PCIE_HW_REV_3_20				0x0320
>>   
>>   #define PCIE_MISC_CPU_2_PCIE_MEM_WIN0_BASE_LIMIT		0x4070
>>   #define  PCIE_MISC_CPU_2_PCIE_MEM_WIN0_BASE_LIMIT_LIMIT_MASK	0xfff00000
>> @@ -190,6 +191,7 @@
>>   struct brcm_pcie;
>>   static inline void brcm_pcie_bridge_sw_init_set_7278(struct brcm_pcie *pcie, u32 val);
>>   static inline void brcm_pcie_bridge_sw_init_set_generic(struct brcm_pcie *pcie, u32 val);
>> +static inline void brcm_pcie_perst_set_4908(struct brcm_pcie *pcie, u32 val);
>>   static inline void brcm_pcie_perst_set_7278(struct brcm_pcie *pcie, u32 val);
>>   static inline void brcm_pcie_perst_set_generic(struct brcm_pcie *pcie, u32 val);
>>   
>> @@ -206,6 +208,7 @@ enum {
>>   
>>   enum pcie_type {
>>   	GENERIC,
>> +	BCM4908,
>>   	BCM7278,
>>   	BCM2711,
>>   };
>> @@ -230,6 +233,13 @@ static const struct pcie_cfg_data generic_cfg = {
>>   	.bridge_sw_init_set = brcm_pcie_bridge_sw_init_set_generic,
>>   };
>>   
>> +static const struct pcie_cfg_data bcm4908_cfg = {
>> +	.offsets	= pcie_offsets,
>> +	.type		= BCM4908,
>> +	.perst_set	= brcm_pcie_perst_set_4908,
>> +	.bridge_sw_init_set = brcm_pcie_bridge_sw_init_set_generic,
>> +};
>> +
>>   static const int pcie_offset_bcm7278[] = {
>>   	[RGR1_SW_INIT_1] = 0xc010,
>>   	[EXT_CFG_INDEX] = 0x9000,
>> @@ -282,6 +292,7 @@ struct brcm_pcie {
>>   	const int		*reg_offsets;
>>   	enum pcie_type		type;
>>   	struct reset_control	*rescal;
>> +	struct reset_control	*perst_reset;
>>   	int			num_memc;
>>   	u64			memc_size[PCIE_BRCM_MAX_MEMC];
>>   	u32			hw_rev;
>> @@ -747,6 +758,17 @@ static inline void brcm_pcie_bridge_sw_init_set_7278(struct brcm_pcie *pcie, u32
>>   	writel(tmp, pcie->base + PCIE_RGR1_SW_INIT_1(pcie));
>>   }
>>   
>> +static inline void brcm_pcie_perst_set_4908(struct brcm_pcie *pcie, u32 val)
>> +{
>> +	if (WARN_ONCE(!pcie->perst_reset, "missing PERST# reset controller\n"))
>> +		return;
>> +
>> +	if (val)
>> +		reset_control_assert(pcie->perst_reset);
>> +	else
>> +		reset_control_deassert(pcie->perst_reset);
> 
> This looks good to me now, just one nit, you probably do not support
> suspend/resume on the 4908, likely never will, but you should probably
> pulse the PERST# during PCIe resume, too. With that fixed:
> 
> Acked-by: Florian Fainelli <f.fainelli@gmail.com>

Driver already does that.

Suspend forward trace:
brcm_pcie_suspend()
brcm_pcie_turn_off()
pcie->perst_set(pcie, 1)

Resume forward trace:
brcm_pcie_resume()
brcm_pcie_setup()
pcie->perst_set(pcie, 0)

Correct me if I'm wrong please.

Re: [PATCH V2 2/2] PCI: brcmstb: support BCM4908 with external PERST# signal controller

[Florian Fainelli]

On 12/10/2020 12:46 AM, Rafał Miłecki wrote:
>> This looks good to me now, just one nit, you probably do not support
>> suspend/resume on the 4908, likely never will, but you should probably
>> pulse the PERST# during PCIe resume, too. With that fixed:
>>
>> Acked-by: Florian Fainelli <f.fainelli@gmail.com>
> 
> Driver already does that.
> 
> Suspend forward trace:
> brcm_pcie_suspend()
> brcm_pcie_turn_off()
> pcie->perst_set(pcie, 1)
> 
> Resume forward trace:
> brcm_pcie_resume()
> brcm_pcie_setup()
> pcie->perst_set(pcie, 0)
> 
> Correct me if I'm wrong please.

Nope, it's all good, my memory was incorrectly serving me, since
perst_set() has been moved to a callback you have it called indeed.

Acked-by: Florian Fainelli <f.fainelli@gmail.com>

Thanks!
-- 
Florian