* [PATCH] iio: st-sensors: Convert bindings to YAML
@ 2020-12-02 21:13 Linus Walleij
2020-12-05 15:49 ` Jonathan Cameron
2020-12-09 20:09 ` Rob Herring
0 siblings, 2 replies; 3+ messages in thread
From: Linus Walleij @ 2020-12-02 21:13 UTC (permalink / raw)
To: Jonathan Cameron, linux-iio
Cc: Hartmut Knaack, Lars-Peter Clausen, Peter Meerwald-Stadler,
Linus Walleij, devicetree
Convert this large binding to YAML. It is pretty simple
in it's basic form but the devil is in the details.
Some -if restrictions painstakingly created by reading through
all the datasheets.
Cc: devicetree@vger.kernel.org
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
---
.../devicetree/bindings/iio/st-sensors.txt | 82 -------
.../devicetree/bindings/iio/st-sensors.yaml | 213 ++++++++++++++++++
2 files changed, 213 insertions(+), 82 deletions(-)
delete mode 100644 Documentation/devicetree/bindings/iio/st-sensors.txt
create mode 100644 Documentation/devicetree/bindings/iio/st-sensors.yaml
diff --git a/Documentation/devicetree/bindings/iio/st-sensors.txt b/Documentation/devicetree/bindings/iio/st-sensors.txt
deleted file mode 100644
index 3213599c5071..000000000000
--- a/Documentation/devicetree/bindings/iio/st-sensors.txt
+++ /dev/null
@@ -1,82 +0,0 @@
-STMicroelectronics MEMS sensors
-
-The STMicroelectronics sensor devices are pretty straight-forward I2C or
-SPI devices, all sharing the same device tree descriptions no matter what
-type of sensor it is.
-
-Required properties:
-- compatible: see the list of valid compatible strings below
-- reg: the I2C or SPI address the device will respond to
-
-Optional properties:
-- vdd-supply: an optional regulator that needs to be on to provide VDD
- power to the sensor.
-- vddio-supply: an optional regulator that needs to be on to provide the
- VDD IO power to the sensor.
-- st,drdy-int-pin: the pin on the package that will be used to signal
- "data ready" (valid values: 1 or 2). This property is not configurable
- on all sensors.
-- drive-open-drain: the interrupt/data ready line will be configured
- as open drain, which is useful if several sensors share the same
- interrupt line. (This binding is taken from pinctrl/pinctrl-bindings.txt)
- This is a boolean property.
-
-Sensors may also have applicable pin control settings, those use the
-standard bindings from pinctrl/pinctrl-bindings.txt.
-
-Valid compatible strings:
-
-Accelerometers:
-- st,lis3lv02d (deprecated, use st,lis3lv02dl-accel)
-- st,lis302dl-spi (deprecated, use st,lis3lv02dl-accel)
-- st,lis3lv02dl-accel
-- st,lsm303dlh-accel
-- st,lsm303dlhc-accel
-- st,lis3dh-accel
-- st,lsm330d-accel
-- st,lsm330dl-accel
-- st,lsm330dlc-accel
-- st,lis331dl-accel
-- st,lis331dlh-accel
-- st,lsm303dl-accel
-- st,lsm303dlm-accel
-- st,lsm330-accel
-- st,lsm303agr-accel
-- st,lis2dh12-accel
-- st,h3lis331dl-accel
-- st,lng2dm-accel
-- st,lis3l02dq
-- st,lis2dw12
-- st,lis3dhh
-- st,lis3de
-- st,lis2de12
-- st,lis2hh12
-
-Gyroscopes:
-- st,l3g4200d-gyro
-- st,lsm330d-gyro
-- st,lsm330dl-gyro
-- st,lsm330dlc-gyro
-- st,l3gd20-gyro
-- st,l3gd20h-gyro
-- st,l3g4is-gyro
-- st,lsm330-gyro
-- st,lsm9ds0-gyro
-
-Magnetometers:
-- st,lsm303agr-magn
-- st,lsm303dlh-magn
-- st,lsm303dlhc-magn
-- st,lsm303dlm-magn
-- st,lis3mdl-magn
-- st,lis2mdl
-- st,lsm9ds1-magn
-
-Pressure sensors:
-- st,lps001wp-press
-- st,lps25h-press
-- st,lps331ap-press
-- st,lps22hb-press
-- st,lps33hw
-- st,lps35hw
-- st,lps22hh
diff --git a/Documentation/devicetree/bindings/iio/st-sensors.yaml b/Documentation/devicetree/bindings/iio/st-sensors.yaml
new file mode 100644
index 000000000000..6435bbedfd9a
--- /dev/null
+++ b/Documentation/devicetree/bindings/iio/st-sensors.yaml
@@ -0,0 +1,213 @@
+# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/iio/st-sensors.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: STMicroelectronics MEMS Sensors
+
+description: The STMicroelectronics sensor devices are pretty straight-forward
+ I2C or SPI devices, all sharing the same device tree descriptions no matter
+ what type of sensor it is.
+
+maintainers:
+ - Linus Walleij <linus.walleij@linaro.org>
+
+properties:
+ compatible:
+ oneOf:
+ - description: STMicroelectronics Accelerometers
+ enum:
+ - st,h3lis331dl-accel
+ - st,lis2de12
+ - st,lis2dw12
+ - st,lis2hh12
+ - st,lis2dh12-accel
+ - st,lis331dl-accel
+ - st,lis331dlh-accel
+ - st,lis3de
+ - st,lis3dh-accel
+ - st,lis3dhh
+ - st,lis3l02dq
+ - st,lis3lv02dl-accel
+ - st,lng2dm-accel
+ - st,lsm303agr-accel
+ - st,lsm303dl-accel
+ - st,lsm303dlh-accel
+ - st,lsm303dlhc-accel
+ - st,lsm303dlm-accel
+ - st,lsm330-accel
+ - st,lsm330d-accel
+ - st,lsm330dl-accel
+ - st,lsm330dlc-accel
+ - description: STMicroelectronics Gyroscopes
+ enum:
+ - st,l3g4200d-gyro
+ - st,l3g4is-gyro
+ - st,l3gd20-gyro
+ - st,l3gd20h-gyro
+ - st,lsm330-gyro
+ - st,lsm330d-gyro
+ - st,lsm330dl-gyro
+ - st,lsm330dlc-gyro
+ - st,lsm9ds0-gyro
+ - description: STMicroelectronics Magnetometers
+ enum:
+ - st,lis2mdl
+ - st,lis3mdl-magn
+ - st,lsm303agr-magn
+ - st,lsm303dlh-magn
+ - st,lsm303dlhc-magn
+ - st,lsm303dlm-magn
+ - st,lsm9ds1-magn
+ - description: STMicroelectronics Pressure Sensors
+ enum:
+ - st,lps001wp-press
+ - st,lps22hb-press
+ - st,lps22hh
+ - st,lps25h-press
+ - st,lps331ap-press
+ - st,lps33hw
+ - st,lps35hw
+ - description: Deprecated bindings
+ enum:
+ - st,lis302dl-spi
+ - st,lis3lv02d
+ deprecated: true
+
+ reg:
+ maxItems: 1
+
+ interrupts:
+ description: interrupt line(s) connected to the DRDY line(s) and/or the
+ Intertial interrupt lines INT1 and INT2 if these exist. This means up to
+ three interrupts, and the DRDY must be the first one if it exists on
+ the package. The trigger edge of the interrupts is sometimes software
+ configurable in the hardware so the operating system should parse this
+ flag and set up the trigger edge as indicated in the device tree.
+ minItems: 1
+ maxItems: 2
+
+ vdd-supply: true
+ vddio-supply: true
+
+ st,drdy-int-pin:
+ $ref: /schemas/types.yaml#/definitions/uint32
+ maxItems: 1
+ description: the pin on the package that will be used to signal
+ "data ready" (valid values 1 or 2). This property is not configurable
+ on all sensors.
+ items:
+ minimum: 1
+ maximum: 2
+
+ drive-open-drain:
+ type: boolean
+ description: the interrupt/data ready line will be configured
+ as open drain, which is useful if several sensors share the same
+ interrupt line. (This binding is taken from pinctrl.)
+
+ mount-matrix:
+ description: an optional 3x3 mounting rotation matrix.
+
+allOf:
+ - if:
+ properties:
+ compatible:
+ enum:
+ # These have no interrupts
+ - st,lps001wp
+ then:
+ properties:
+ interrupts: false
+ st,drdy-int-pin: false
+ drive-open-drain: false
+
+ - if:
+ properties:
+ compatible:
+ enum:
+ # These have only DRDY
+ - st,lis2mdl
+ - st,lis3l02dq
+ - st,lis3lv02dl-accel
+ - st,lps22hb-press
+ - st,lps22hh
+ - st,lps25h-press
+ - st,lps33hw
+ - st,lps35hw
+ - st,lsm303agr-magn
+ - st,lsm303dlh-magn
+ - st,lsm303dlhc-magn
+ - st,lsm303dlm-magn
+ then:
+ properties:
+ interrupts:
+ maxItems: 1
+ st,drdy-int-pin: false
+
+ - if:
+ properties:
+ compatible:
+ enum:
+ # Two intertial interrupts i.e. accelerometer/gyro interrupts
+ - st,h3lis331dl-accel
+ - st,l3g4200d-gyro
+ - st,l3g4is-gyro
+ - st,l3gd20-gyro
+ - st,l3gd20h-gyro
+ - st,lis2de12
+ - st,lis2dw12
+ - st,lis2hh12
+ - st,lis2dh12-accel
+ - st,lis331dl-accel
+ - st,lis331dlh-accel
+ - st,lis3de
+ - st,lis3dh-accel
+ - st,lis3dhh
+ - st,lis3mdl-magn
+ - st,lng2dm-accel
+ - st,lps331ap-press
+ - st,lsm303agr-accel
+ - st,lsm303dlh-accel
+ - st,lsm303dlhc-accel
+ - st,lsm303dlm-accel
+ - st,lsm330-accel
+ - st,lsm330-gyro
+ - st,lsm330d-accel
+ - st,lsm330d-gyro
+ - st,lsm330dl-accel
+ - st,lsm330dl-gyro
+ - st,lsm330dlc-accel
+ - st,lsm330dlc-gyro
+ - st,lsm9ds0-gyro
+ - st,lsm9ds1-magn
+ then:
+ properties:
+ interrupts:
+ maxItems: 2
+
+required:
+ - compatible
+ - reg
+
+additionalProperties: false
+
+examples:
+ - |
+ #include <dt-bindings/interrupt-controller/irq.h>
+ #include <dt-bindings/gpio/gpio.h>
+ i2c {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ accelerometer@1c {
+ compatible = "st,lis331dl-accel";
+ reg = <0x1c>;
+ st,drdy-int-pin = <1>;
+ vdd-supply = <&ldo1>;
+ vddio-supply = <&ldo2>;
+ interrupt-parent = <&gpio>;
+ interrupts = <18 IRQ_TYPE_EDGE_RISING>, <19 IRQ_TYPE_EDGE_RISING>;
+ };
+ };
--
2.26.2
^ permalink raw reply related [flat|nested] 3+ messages in thread
* Re: [PATCH] iio: st-sensors: Convert bindings to YAML
2020-12-02 21:13 [PATCH] iio: st-sensors: Convert bindings to YAML Linus Walleij
@ 2020-12-05 15:49 ` Jonathan Cameron
2020-12-09 20:09 ` Rob Herring
1 sibling, 0 replies; 3+ messages in thread
From: Jonathan Cameron @ 2020-12-05 15:49 UTC (permalink / raw)
To: Linus Walleij
Cc: linux-iio, Hartmut Knaack, Lars-Peter Clausen,
Peter Meerwald-Stadler, devicetree
On Wed, 2 Dec 2020 22:13:58 +0100
Linus Walleij <linus.walleij@linaro.org> wrote:
> Convert this large binding to YAML. It is pretty simple
> in it's basic form but the devil is in the details.
> Some -if restrictions painstakingly created by reading through
> all the datasheets.
>
> Cc: devicetree@vger.kernel.org
> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Subject to the fact you already picked up on the much less precise
binding doc conversion I did (was a conversion whereas this is
an improvement :)
Looks good to me. One minor suggestion in line.
Unfortunate this hit just after I'd applied the lesser version :(
> ---
> .../devicetree/bindings/iio/st-sensors.txt | 82 -------
> .../devicetree/bindings/iio/st-sensors.yaml | 213 ++++++++++++++++++
> 2 files changed, 213 insertions(+), 82 deletions(-)
> delete mode 100644 Documentation/devicetree/bindings/iio/st-sensors.txt
> create mode 100644 Documentation/devicetree/bindings/iio/st-sensors.yaml
>
> diff --git a/Documentation/devicetree/bindings/iio/st-sensors.txt b/Documentation/devicetree/bindings/iio/st-sensors.txt
> deleted file mode 100644
> index 3213599c5071..000000000000
> --- a/Documentation/devicetree/bindings/iio/st-sensors.txt
> +++ /dev/null
> @@ -1,82 +0,0 @@
> -STMicroelectronics MEMS sensors
> -
> -The STMicroelectronics sensor devices are pretty straight-forward I2C or
> -SPI devices, all sharing the same device tree descriptions no matter what
> -type of sensor it is.
> -
> -Required properties:
> -- compatible: see the list of valid compatible strings below
> -- reg: the I2C or SPI address the device will respond to
> -
> -Optional properties:
> -- vdd-supply: an optional regulator that needs to be on to provide VDD
> - power to the sensor.
> -- vddio-supply: an optional regulator that needs to be on to provide the
> - VDD IO power to the sensor.
> -- st,drdy-int-pin: the pin on the package that will be used to signal
> - "data ready" (valid values: 1 or 2). This property is not configurable
> - on all sensors.
> -- drive-open-drain: the interrupt/data ready line will be configured
> - as open drain, which is useful if several sensors share the same
> - interrupt line. (This binding is taken from pinctrl/pinctrl-bindings.txt)
> - This is a boolean property.
> -
> -Sensors may also have applicable pin control settings, those use the
> -standard bindings from pinctrl/pinctrl-bindings.txt.
> -
> -Valid compatible strings:
> -
> -Accelerometers:
> -- st,lis3lv02d (deprecated, use st,lis3lv02dl-accel)
> -- st,lis302dl-spi (deprecated, use st,lis3lv02dl-accel)
> -- st,lis3lv02dl-accel
> -- st,lsm303dlh-accel
> -- st,lsm303dlhc-accel
> -- st,lis3dh-accel
> -- st,lsm330d-accel
> -- st,lsm330dl-accel
> -- st,lsm330dlc-accel
> -- st,lis331dl-accel
> -- st,lis331dlh-accel
> -- st,lsm303dl-accel
> -- st,lsm303dlm-accel
> -- st,lsm330-accel
> -- st,lsm303agr-accel
> -- st,lis2dh12-accel
> -- st,h3lis331dl-accel
> -- st,lng2dm-accel
> -- st,lis3l02dq
> -- st,lis2dw12
> -- st,lis3dhh
> -- st,lis3de
> -- st,lis2de12
> -- st,lis2hh12
> -
> -Gyroscopes:
> -- st,l3g4200d-gyro
> -- st,lsm330d-gyro
> -- st,lsm330dl-gyro
> -- st,lsm330dlc-gyro
> -- st,l3gd20-gyro
> -- st,l3gd20h-gyro
> -- st,l3g4is-gyro
> -- st,lsm330-gyro
> -- st,lsm9ds0-gyro
> -
> -Magnetometers:
> -- st,lsm303agr-magn
> -- st,lsm303dlh-magn
> -- st,lsm303dlhc-magn
> -- st,lsm303dlm-magn
> -- st,lis3mdl-magn
> -- st,lis2mdl
> -- st,lsm9ds1-magn
> -
> -Pressure sensors:
> -- st,lps001wp-press
> -- st,lps25h-press
> -- st,lps331ap-press
> -- st,lps22hb-press
> -- st,lps33hw
> -- st,lps35hw
> -- st,lps22hh
> diff --git a/Documentation/devicetree/bindings/iio/st-sensors.yaml b/Documentation/devicetree/bindings/iio/st-sensors.yaml
> new file mode 100644
> index 000000000000..6435bbedfd9a
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/iio/st-sensors.yaml
> @@ -0,0 +1,213 @@
> +# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause)
> +%YAML 1.2
> +---
> +$id: http://devicetree.org/schemas/iio/st-sensors.yaml#
> +$schema: http://devicetree.org/meta-schemas/core.yaml#
> +
> +title: STMicroelectronics MEMS Sensors
> +
> +description: The STMicroelectronics sensor devices are pretty straight-forward
> + I2C or SPI devices, all sharing the same device tree descriptions no matter
> + what type of sensor it is.
> +
> +maintainers:
> + - Linus Walleij <linus.walleij@linaro.org>
> +
> +properties:
> + compatible:
> + oneOf:
> + - description: STMicroelectronics Accelerometers
> + enum:
> + - st,h3lis331dl-accel
> + - st,lis2de12
> + - st,lis2dw12
> + - st,lis2hh12
> + - st,lis2dh12-accel
> + - st,lis331dl-accel
> + - st,lis331dlh-accel
> + - st,lis3de
> + - st,lis3dh-accel
> + - st,lis3dhh
> + - st,lis3l02dq
> + - st,lis3lv02dl-accel
> + - st,lng2dm-accel
> + - st,lsm303agr-accel
> + - st,lsm303dl-accel
> + - st,lsm303dlh-accel
> + - st,lsm303dlhc-accel
> + - st,lsm303dlm-accel
> + - st,lsm330-accel
> + - st,lsm330d-accel
> + - st,lsm330dl-accel
> + - st,lsm330dlc-accel
> + - description: STMicroelectronics Gyroscopes
> + enum:
> + - st,l3g4200d-gyro
> + - st,l3g4is-gyro
> + - st,l3gd20-gyro
> + - st,l3gd20h-gyro
> + - st,lsm330-gyro
> + - st,lsm330d-gyro
> + - st,lsm330dl-gyro
> + - st,lsm330dlc-gyro
> + - st,lsm9ds0-gyro
> + - description: STMicroelectronics Magnetometers
> + enum:
> + - st,lis2mdl
> + - st,lis3mdl-magn
> + - st,lsm303agr-magn
> + - st,lsm303dlh-magn
> + - st,lsm303dlhc-magn
> + - st,lsm303dlm-magn
> + - st,lsm9ds1-magn
> + - description: STMicroelectronics Pressure Sensors
> + enum:
> + - st,lps001wp-press
> + - st,lps22hb-press
> + - st,lps22hh
> + - st,lps25h-press
> + - st,lps331ap-press
> + - st,lps33hw
> + - st,lps35hw
> + - description: Deprecated bindings
> + enum:
> + - st,lis302dl-spi
> + - st,lis3lv02d
> + deprecated: true
> +
> + reg:
> + maxItems: 1
> +
> + interrupts:
> + description: interrupt line(s) connected to the DRDY line(s) and/or the
> + Intertial interrupt lines INT1 and INT2 if these exist. This means up to
> + three interrupts, and the DRDY must be the first one if it exists on
> + the package. The trigger edge of the interrupts is sometimes software
> + configurable in the hardware so the operating system should parse this
> + flag and set up the trigger edge as indicated in the device tree.
> + minItems: 1
> + maxItems: 2
> +
> + vdd-supply: true
> + vddio-supply: true
> +
> + st,drdy-int-pin:
> + $ref: /schemas/types.yaml#/definitions/uint32
> + maxItems: 1
> + description: the pin on the package that will be used to signal
> + "data ready" (valid values 1 or 2). This property is not configurable
> + on all sensors.
> + items:
> + minimum: 1
> + maximum: 2
Maybe enum [1, 2]?
> +
> + drive-open-drain:
> + type: boolean
> + description: the interrupt/data ready line will be configured
> + as open drain, which is useful if several sensors share the same
> + interrupt line. (This binding is taken from pinctrl.)
> +
> + mount-matrix:
> + description: an optional 3x3 mounting rotation matrix.
> +
> +allOf:
> + - if:
> + properties:
> + compatible:
> + enum:
> + # These have no interrupts
> + - st,lps001wp
> + then:
> + properties:
> + interrupts: false
> + st,drdy-int-pin: false
> + drive-open-drain: false
> +
> + - if:
> + properties:
> + compatible:
> + enum:
> + # These have only DRDY
> + - st,lis2mdl
> + - st,lis3l02dq
> + - st,lis3lv02dl-accel
> + - st,lps22hb-press
> + - st,lps22hh
> + - st,lps25h-press
> + - st,lps33hw
> + - st,lps35hw
> + - st,lsm303agr-magn
> + - st,lsm303dlh-magn
> + - st,lsm303dlhc-magn
> + - st,lsm303dlm-magn
> + then:
> + properties:
> + interrupts:
> + maxItems: 1
> + st,drdy-int-pin: false
> +
> + - if:
> + properties:
> + compatible:
> + enum:
> + # Two intertial interrupts i.e. accelerometer/gyro interrupts
> + - st,h3lis331dl-accel
> + - st,l3g4200d-gyro
> + - st,l3g4is-gyro
> + - st,l3gd20-gyro
> + - st,l3gd20h-gyro
> + - st,lis2de12
> + - st,lis2dw12
> + - st,lis2hh12
> + - st,lis2dh12-accel
> + - st,lis331dl-accel
> + - st,lis331dlh-accel
> + - st,lis3de
> + - st,lis3dh-accel
> + - st,lis3dhh
> + - st,lis3mdl-magn
> + - st,lng2dm-accel
> + - st,lps331ap-press
> + - st,lsm303agr-accel
> + - st,lsm303dlh-accel
> + - st,lsm303dlhc-accel
> + - st,lsm303dlm-accel
> + - st,lsm330-accel
> + - st,lsm330-gyro
> + - st,lsm330d-accel
> + - st,lsm330d-gyro
> + - st,lsm330dl-accel
> + - st,lsm330dl-gyro
> + - st,lsm330dlc-accel
> + - st,lsm330dlc-gyro
> + - st,lsm9ds0-gyro
> + - st,lsm9ds1-magn
> + then:
> + properties:
> + interrupts:
> + maxItems: 2
> +
> +required:
> + - compatible
> + - reg
> +
> +additionalProperties: false
> +
> +examples:
> + - |
> + #include <dt-bindings/interrupt-controller/irq.h>
> + #include <dt-bindings/gpio/gpio.h>
> + i2c {
> + #address-cells = <1>;
> + #size-cells = <0>;
> +
> + accelerometer@1c {
> + compatible = "st,lis331dl-accel";
> + reg = <0x1c>;
> + st,drdy-int-pin = <1>;
> + vdd-supply = <&ldo1>;
> + vddio-supply = <&ldo2>;
> + interrupt-parent = <&gpio>;
> + interrupts = <18 IRQ_TYPE_EDGE_RISING>, <19 IRQ_TYPE_EDGE_RISING>;
> + };
> + };
^ permalink raw reply [flat|nested] 3+ messages in thread
* Re: [PATCH] iio: st-sensors: Convert bindings to YAML
2020-12-02 21:13 [PATCH] iio: st-sensors: Convert bindings to YAML Linus Walleij
2020-12-05 15:49 ` Jonathan Cameron
@ 2020-12-09 20:09 ` Rob Herring
1 sibling, 0 replies; 3+ messages in thread
From: Rob Herring @ 2020-12-09 20:09 UTC (permalink / raw)
To: Linus Walleij
Cc: linux-iio, devicetree, Hartmut Knaack, Lars-Peter Clausen,
Peter Meerwald-Stadler, Jonathan Cameron
On Wed, 02 Dec 2020 22:13:58 +0100, Linus Walleij wrote:
> Convert this large binding to YAML. It is pretty simple
> in it's basic form but the devil is in the details.
> Some -if restrictions painstakingly created by reading through
> all the datasheets.
>
> Cc: devicetree@vger.kernel.org
> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
> ---
> .../devicetree/bindings/iio/st-sensors.txt | 82 -------
> .../devicetree/bindings/iio/st-sensors.yaml | 213 ++++++++++++++++++
> 2 files changed, 213 insertions(+), 82 deletions(-)
> delete mode 100644 Documentation/devicetree/bindings/iio/st-sensors.txt
> create mode 100644 Documentation/devicetree/bindings/iio/st-sensors.yaml
>
Reviewed-by: Rob Herring <robh@kernel.org>
^ permalink raw reply [flat|nested] 3+ messages in thread
end of thread, other threads:[~2020-12-09 20:10 UTC | newest]
Thread overview: 3+ messages (download: mbox.gz / follow: Atom feed)
-- links below jump to the message on this page --
2020-12-02 21:13 [PATCH] iio: st-sensors: Convert bindings to YAML Linus Walleij
2020-12-05 15:49 ` Jonathan Cameron
2020-12-09 20:09 ` Rob Herring
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).