[PATCH v5 0/4] arm64: dts: allwinner: Add Anbernic RG35XX (Plus/H/2024) support

[PATCH v5 0/4] arm64: dts: allwinner: Add Anbernic RG35XX (Plus/H/2024) support

[Ryan Walklin]

Thanks again for additional reviews. Have made the requested changes, and added some commentary about the SD2 low-voltage signalling, which will require a GPIO-switched regulator for the 3.3v->1.8v transition. This is not yet implemented/modeled, so for now a fixed 3.3v supply is used, and noted that an additional regulator define is required for SD2 operation and stable Bluetooth. However SD2, Wifi and BT are all working with the current state.

Original cover below.
--

The Anbernic RG35XX is a family of handheld gaming devices. There are 4 variants, of which 3 using the Allwinner H700 chip are covered by this patchset. The fourth (released first and named simply RG35XX) uses an Actions Semiconductor ATM7039s which is a 32-bit Cortex-A9 chip with no mainline support and is not covered.

Common features (RG35XX-2024):
- Allwinner H700 @ 1.5GHz (H616 variant exposing RGB LCD and NMI pins, with 4x Cortex-A53 Cores and a Mali G31 GPU)
- 1 GB LPDDR4 DRAM
- AXP717 PMIC (patches accepted in mfd-next [1])
- 3.5" 640x480 RGB LCD
- Mini-HDMI, 3.5mm audio jack, mono speaker, two microSD slots and USB-C (USB 2.0) for power.

RG35XX-Plus adds:
- RTL8821CS SDIO Wifi/BT chip

RG35XX-H (Horizontal form-factor) adds:
- RTL8821CS SDIO Wifi/BT chip
- Two analog thumbsticks
- Second USB-C port
- Stereo speaker

Patch 1 adds the DT bindings for the board names, Patch 2 adds the -2024 device as a common base, Patch 3 adds Wifi/BT support for the -Plus (and -H), and Patch 3 adds the second USB and thumbsticks for the -H. The -H is a strict superset of the -Plus, which is in turn a strict superset of the -2024, so this translates quite neatly.

LCD, HDMI, audio, and GPU support are not yet ready and relying on out-of-tree patches currently, so will be added once these drivers are mainlined.

Ryan

Signed-off-by: Ryan Walklin <ryan@testtoast.com>

Ryan Walklin (4):
  dt-bindings: arm: sunxi: document Anbernic RG35XX handheld gaming
    device variants
  arm64: dts: allwinner: h700: Add RG35XX 2024 DTS
  arm64: dts: allwinner: h700: Add RG35XX-Plus DTS
  arm64: dts: allwinner: h700: Add RG35XX-H DTS

 .../devicetree/bindings/arm/sunxi.yaml        |  15 +
 arch/arm64/boot/dts/allwinner/Makefile        |   3 +
 .../sun50i-h700-anbernic-rg35xx-2024.dts      | 346 ++++++++++++++++++
 .../sun50i-h700-anbernic-rg35xx-h.dts         |  36 ++
 .../sun50i-h700-anbernic-rg35xx-plus.dts      |  53 +++
 5 files changed, 453 insertions(+)
 create mode 100644 arch/arm64/boot/dts/allwinner/sun50i-h700-anbernic-rg35xx-2024.dts
 create mode 100644 arch/arm64/boot/dts/allwinner/sun50i-h700-anbernic-rg35xx-h.dts
 create mode 100644 arch/arm64/boot/dts/allwinner/sun50i-h700-anbernic-rg35xx-plus.dts

-- 
2.44.0

[PATCH v5 1/4] dt-bindings: arm: sunxi: document Anbernic RG35XX handheld gaming device variants

[Ryan Walklin]

RG35XX 2024: Base version with Allwinner H700
RG35XX Plus: Adds Wifi/BT
RG35XX H: Adds second USB port and analog sticks to -Plus in horizontal form factor

Use three separate device descriptions rather than enum as per existing sunxi binding style.

Signed-off-by: Ryan Walklin <ryan@testtoast.com>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
---
 Documentation/devicetree/bindings/arm/sunxi.yaml | 15 +++++++++++++++
 1 file changed, 15 insertions(+)

diff --git a/Documentation/devicetree/bindings/arm/sunxi.yaml b/Documentation/devicetree/bindings/arm/sunxi.yaml
index 09d835db6db5..fc10f54561c9 100644
--- a/Documentation/devicetree/bindings/arm/sunxi.yaml
+++ b/Documentation/devicetree/bindings/arm/sunxi.yaml
@@ -56,6 +56,21 @@ properties:
           - const: anbernic,rg-nano
           - const: allwinner,sun8i-v3s
 
+      - description: Anbernic RG35XX (2024)
+      - items:
+          - const: anbernic,rg35xx-2024
+          - const: allwinner,sun50i-h700
+
+      - description: Anbernic RG35XX Plus
+      - items:
+          - const: anbernic,rg35xx-plus
+          - const: allwinner,sun50i-h700
+
+      - description: Anbernic RG35XX H
+      - items:
+          - const: anbernic,rg35xx-h
+          - const: allwinner,sun50i-h700
+
       - description: Amarula A64 Relic
         items:
           - const: amarula,a64-relic
-- 
2.44.0

[PATCH v5 2/4] arm64: dts: allwinner: h700: Add RG35XX 2024 DTS

[Ryan Walklin]

The base model RG35XX (2024) is a handheld gaming device based on an
Allwinner H700 chip.

The H700 is a H616 variant (4x ARM Cortex-A53 cores @ 1.5Ghz with Mali G31
GPU) which exposes RGB LCD and NMI pins.

Device features:
- Allwinner H700 @ 1.5GHz
- 1GB LPDDR4 DRAM
- X-Powers AXP717 PMIC
- 3.5" 640x480 RGB LCD
- Two microSD slots
- Mini-HDMI out
- GPIO keypad
- 3.5mm headphone jack
- USB-C charging port

Enabled in this DTS:
- AXP717 PMIC with RSB serial interface, regulators and NMI interrupt
  controller
- Power LED (charge LED on device controlled directly by PMIC)
- Serial UART (accessible from headers on the board)
- MMC slots (SD2 appears to have a GPIO-switched regulator for 1.8v
  low-voltage signalling, this is not yet modeled so a fixed-regulator and
  3.3v and 1.8v rails from the PMIC are used. A switched regulator will be
  confirmed and posted in a follow-up patch)

Signed-off-by: Ryan Walklin <ryan@testtoast.com>
---
Changelog v1..v2:
- Update copyright
- Spaces -> Tabs
- Add cpufreq support
- Remove MMC aliases
- Fix GPIO button and regulator node names
- Note unused AXP717 regulators
- Update regulators for SD slots
- Remove unused I2C3 device
- Update NMI interrupt controller for AXP717, requires H616 support patch in dt-next [1]
- Add chassis-type
- Address USB EHCI/OHCI0 correctly and add usb vbus supply
- Add PIO vcc-pg-supply
- Correct boost regulator voltage and name

Changelog v2..v3:
- Remove cpufreq support (patch still pending for 6.10, will followup with enablement patch once opp table merged)
- Add dtb to Makefile
- Remove unnecessary duplicated PLL regulator
- Remove unimplemented/not-present drive-vbus feature from AXP717
- Rename CLDO3 to "vcc-io", inferring function from board testing by Chris Morgan
- Correct MMC1 vmmc-supply to CLDO3 and MMC2 to CLDO4
- Reduce DCDC1 "vdd-cpu" supply voltage range to 0.9v-1.1v to match lowest OPP voltage
- Identify DCDC2 as GPU supply - rename to "vdd-gpu-sys", remove always-on and use fixed 0.94v voltage
- Fix indentation
- Correct boot/always-on states and voltages for various regulators from vendor BSP
- Change USB-OTG mode to "peripheral" and correct comment
- Correct and add remaining PIO supplies
- Move volume key GPIOs to separate block to allow key repeat
- Alphabetically orrder gamepad GPIOs
- Move changelog and links below fold-line
- Remove USB 3.3v VCC-USB and VCC-SD2 regulators pending further hardware investigation (to be submitted as subsequent patch)
- Constrain boost regulator voltage to 5.0v to 5.2v to capture default voltage of 5.126v

Changelog v3..v4:
- Cluster USB nodes
- Do not define voltage range for currently unused CLDO1 (connected to audio codec according to vendor BSP - driver not yet implemented) and ALDO3 (1.8v).
- Note voltages set for currently unused regulators from vendor BSP in comments to aid identification
- Remove regulator-boot-on from several regulators where it was not required
- Fix indentation
- Add "disable-wp" for SD2 as for SD1 (doesn't make sense for micro-SD)
- Restore fixed 3.3v regulator for SD2 (vcc_3v3_sd2), which is required for SD2 to function. ALDO1 appears to be the 1.8v supply required for low-voltage UHS-I signalling, however a GPIO pin to switch between the supplies is not yet confirmed (likely PE4) and will be implemented in a subsequent patch.

Changelog v4..v5:
- Remove comment referencing vendor BSP node
- Reorder nodes alphabetically and remove empty lines
- Add note to commit message about SD2 regulators, rename vcc_3v3_sd2

[1]: https://git.kernel.org/pub/scm/linux/kernel/git/robh/linux.git/commit/?h=dt/next&id=d47bca77bf3ab475c33b3929c33c80aeb49df35c

Signed-off-by: Ryan Walklin <ryan@testtoast.com>
---
 arch/arm64/boot/dts/allwinner/Makefile        |   1 +
 .../sun50i-h700-anbernic-rg35xx-2024.dts      | 346 ++++++++++++++++++
 2 files changed, 347 insertions(+)
 create mode 100644 arch/arm64/boot/dts/allwinner/sun50i-h700-anbernic-rg35xx-2024.dts

diff --git a/arch/arm64/boot/dts/allwinner/Makefile b/arch/arm64/boot/dts/allwinner/Makefile
index 21149b346a60..6f997157968e 100644
--- a/arch/arm64/boot/dts/allwinner/Makefile
+++ b/arch/arm64/boot/dts/allwinner/Makefile
@@ -47,3 +47,4 @@ dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h618-longanpi-3h.dtb
 dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h618-orangepi-zero2w.dtb
 dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h618-orangepi-zero3.dtb
 dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h618-transpeed-8k618-t.dtb
+dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h700-anbernic-rg35xx-2024.dtb
diff --git a/arch/arm64/boot/dts/allwinner/sun50i-h700-anbernic-rg35xx-2024.dts b/arch/arm64/boot/dts/allwinner/sun50i-h700-anbernic-rg35xx-2024.dts
new file mode 100644
index 000000000000..b90ffa7785c8
--- /dev/null
+++ b/arch/arm64/boot/dts/allwinner/sun50i-h700-anbernic-rg35xx-2024.dts
@@ -0,0 +1,346 @@
+// SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+/*
+ * Copyright (C) 2024 Ryan Walklin <ryan@testtoast.com>.
+ */
+
+/dts-v1/;
+
+#include "sun50i-h616.dtsi"
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/linux-event-codes.h>
+#include <dt-bindings/interrupt-controller/arm-gic.h>
+#include <dt-bindings/leds/common.h>
+
+/ {
+	model = "Anbernic RG35XX 2024";
+	chassis-type = "handset";
+	compatible = "anbernic,rg35xx-2024", "allwinner,sun50i-h700";
+
+	aliases {
+		serial0 = &uart0;
+	};
+
+	chosen {
+		stdout-path = "serial0:115200n8";
+	};
+
+	gpio_keys_gamepad: gpio-keys-gamepad {
+		compatible = "gpio-keys";
+
+		button-a {
+			label = "Action-Pad A";
+			gpios = <&pio 0 0 GPIO_ACTIVE_LOW>; /* PA0 */
+			linux,input-type = <EV_KEY>;
+			linux,code = <BTN_EAST>;
+		};
+
+		button-b {
+			label = "Action-Pad B";
+			gpios = <&pio 0 1 GPIO_ACTIVE_LOW>; /* PA1 */
+			linux,input-type = <EV_KEY>;
+			linux,code = <BTN_SOUTH>;
+		};
+
+		button-down {
+			label = "D-Pad Down";
+			gpios = <&pio 4 0 GPIO_ACTIVE_LOW>; /* PE0 */
+			linux,input-type = <EV_KEY>;
+			linux,code = <BTN_DPAD_DOWN>;
+		};
+
+		button-l1 {
+			label = "Key L1";
+			gpios = <&pio 0 10 GPIO_ACTIVE_LOW>; /* PA10 */
+			linux,input-type = <EV_KEY>;
+			linux,code = <BTN_TL>;
+		};
+
+		button-l2 {
+			label = "Key L2";
+			gpios = <&pio 0 11 GPIO_ACTIVE_LOW>; /* PA11 */
+			linux,input-type = <EV_KEY>;
+			linux,code = <BTN_TL2>;
+		};
+
+		button-left {
+			label = "D-Pad left";
+			gpios = <&pio 0 8 GPIO_ACTIVE_LOW>; /* PA8 */
+			linux,input-type = <EV_KEY>;
+			linux,code = <BTN_DPAD_LEFT>;
+		};
+
+		button-menu {
+			label = "Key Menu";
+			gpios = <&pio 4 3 GPIO_ACTIVE_LOW>; /* PE3 */
+			linux,input-type = <EV_KEY>;
+			linux,code = <BTN_MODE>;
+		};
+
+		button-r1 {
+			label = "Key R1";
+			gpios = <&pio 0 12 GPIO_ACTIVE_LOW>; /* PA12 */
+			linux,input-type = <EV_KEY>;
+			linux,code = <BTN_TR>;
+		};
+
+		button-r2 {
+			label = "Key R2";
+			gpios = <&pio 0 7 GPIO_ACTIVE_LOW>; /* PA7 */
+			linux,input-type = <EV_KEY>;
+			linux,code = <BTN_TR2>;
+		};
+
+		button-right {
+			label = "D-Pad Right";
+			gpios = <&pio 0 9 GPIO_ACTIVE_LOW>; /* PA9 */
+			linux,input-type = <EV_KEY>;
+			linux,code = <BTN_DPAD_RIGHT>;
+		};
+
+		button-select {
+			label = "Key Select";
+			gpios = <&pio 0 5 GPIO_ACTIVE_LOW>; /* PA5 */
+			linux,input-type = <EV_KEY>;
+			linux,code = <BTN_SELECT>;
+		};
+		button-start {
+			label = "Key Start";
+			gpios = <&pio 0 4 GPIO_ACTIVE_LOW>; /* PA4 */
+			linux,input-type = <EV_KEY>;
+			linux,code = <BTN_START>;
+		};
+
+		button-up {
+			label = "D-Pad Up";
+			gpios = <&pio 0 6 GPIO_ACTIVE_LOW>; /* PA6 */
+			linux,input-type = <EV_KEY>;
+			linux,code = <BTN_DPAD_UP>;
+		};
+
+		button-x {
+			label = "Action-Pad X";
+			gpios = <&pio 0 3 GPIO_ACTIVE_LOW>; /* PA3 */
+			linux,input-type = <EV_KEY>;
+			linux,code = <BTN_NORTH>;
+		};
+
+		button-y {
+			label = "Action Pad Y";
+			gpios = <&pio 0 2 GPIO_ACTIVE_LOW>; /* PA2 */
+			linux,input-type = <EV_KEY>;
+			linux,code = <BTN_WEST>;
+		};
+	};
+
+	gpio-keys-volume {
+		compatible = "gpio-keys";
+		autorepeat;
+
+		button-vol-up {
+			label = "Key Volume Up";
+			gpios = <&pio 4 1 GPIO_ACTIVE_LOW>; /* PE1 */
+			linux,input-type = <EV_KEY>;
+			linux,code = <KEY_VOLUMEUP>;
+		};
+
+		button-vol-down {
+			label = "Key Volume Down";
+			gpios = <&pio 4 2 GPIO_ACTIVE_LOW>; /* PE2 */
+			linux,input-type = <EV_KEY>;
+			linux,code = <KEY_VOLUMEDOWN>;
+		};
+	};
+
+	leds {
+		compatible = "gpio-leds";
+
+		led-0 {
+			function = LED_FUNCTION_POWER;
+			color = <LED_COLOR_ID_GREEN>;
+			gpios = <&pio 8 12 GPIO_ACTIVE_HIGH>; /* PI12 */
+			default-state = "on";
+		};
+	};
+
+	reg_vcc5v: regulator-vcc5v { /* USB-C power input */
+		compatible = "regulator-fixed";
+		regulator-name = "vcc-5v";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+	};
+
+	vcc_3v3_sd2: regulator-3v3-sd2 { /* GPIO-controlled regulator for SD2 IO */
+		compatible = "regulator-fixed";
+		gpio = <&pio 4 4 GPIO_ACTIVE_HIGH>; /* PE4 */
+		regulator-name = "vcc_3v3_sd2";
+		regulator-max-microvolt = <3300000>;
+		regulator-min-microvolt = <3300000>;
+	};
+};
+
+&cpu0 {
+	cpu-supply = <&reg_dcdc1>;
+};
+
+&ehci0 {
+	status = "okay";
+};
+
+&mmc0 {
+	vmmc-supply = <&reg_cldo3>;
+	disable-wp;
+	cd-gpios = <&pio 5 6 GPIO_ACTIVE_LOW>;  /* PF6 */
+	bus-width = <4>;
+	status = "okay";
+};
+
+&mmc2 {
+	vmmc-supply = <&reg_cldo4>;
+	vqmmc-supply = <&reg_aldo1>;
+	disable-wp;
+	cd-gpios = <&pio 4 22 GPIO_ACTIVE_LOW>; /* PE22 */
+	bus-width = <4>;
+	status = "okay";
+};
+
+&r_rsb {
+	status = "okay";
+
+	axp717: pmic@3a3 {
+		compatible = "x-powers,axp717";
+		reg = <0x3a3>;
+		interrupt-controller;
+		#interrupt-cells = <1>;
+		interrupt-parent = <&nmi_intc>;
+		interrupts = <0 IRQ_TYPE_LEVEL_LOW>;
+
+		vin1-supply = <&reg_vcc5v>;
+		vin2-supply = <&reg_vcc5v>;
+		vin3-supply = <&reg_vcc5v>;
+		vin4-supply = <&reg_vcc5v>;
+
+		regulators {
+			reg_dcdc1: dcdc1 {
+				regulator-always-on;
+				regulator-min-microvolt = <900000>;
+				regulator-max-microvolt = <1100000>;
+				regulator-name = "vdd-cpu";
+			};
+
+			reg_dcdc2: dcdc2 {
+				regulator-always-on;
+				regulator-min-microvolt = <940000>;
+				regulator-max-microvolt = <940000>;
+				regulator-name = "vdd-gpu-sys";
+			};
+
+			reg_dcdc3: dcdc3 {
+				regulator-always-on;
+				regulator-min-microvolt = <1100000>;
+				regulator-max-microvolt = <1100000>;
+				regulator-name = "vdd-dram";
+			};
+
+			reg_aldo1: aldo1 {
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <1800000>;
+				regulator-name = "vcc-sd2";
+			};
+
+			reg_aldo2: aldo2 {
+				/* 1.8v - unused */
+			};
+
+			reg_aldo3: aldo3 {
+				/* 1.8v - unused */
+			};
+
+			reg_aldo4: aldo4 {
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <1800000>;
+				regulator-name = "vcc-pg";
+			};
+
+			reg_bldo1: bldo1 {
+				/* 1.8v - unused */
+			};
+
+			reg_bldo2: bldo2 {
+				regulator-always-on;
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <1800000>;
+				regulator-name = "vcc-pll";
+			};
+
+			reg_bldo3: bldo3 {
+				/* 2.8v - unused */
+			};
+
+			reg_bldo4: bldo4 {
+				/* 1.2v - unused */
+			};
+
+			reg_cldo1: cldo1 {
+				/* 3.3v - audio codec - not yet implemented */
+			};
+
+			reg_cldo2: cldo2 {
+				/* 3.3v - unused */
+			};
+
+			reg_cldo3: cldo3 {
+				regulator-always-on;
+				regulator-min-microvolt = <3300000>;
+				regulator-max-microvolt = <3300000>;
+				regulator-name = "vcc-io";
+			};
+
+			reg_cldo4: cldo4 {
+				regulator-min-microvolt = <3300000>;
+				regulator-max-microvolt = <3300000>;
+				regulator-name = "vcc-wifi";
+			};
+
+			reg_boost: boost {
+				regulator-min-microvolt = <5000000>;
+				regulator-max-microvolt = <5200000>;
+				regulator-name = "boost";
+			};
+
+			reg_cpusldo: cpusldo {
+				/* unused */
+			};
+		};
+	};
+};
+
+&ohci0 {
+	status = "okay";
+};
+
+&pio {
+	vcc-pa-supply = <&reg_cldo3>;
+	vcc-pc-supply = <&reg_cldo3>;
+	vcc-pe-supply = <&reg_cldo3>;
+	vcc-pf-supply = <&reg_cldo3>;
+	vcc-pg-supply = <&reg_aldo4>;
+	vcc-ph-supply = <&reg_cldo3>;
+	vcc-pi-supply = <&reg_cldo3>;
+};
+
+&uart0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&uart0_ph_pins>;
+	status = "okay";
+};
+
+/* the AXP717 has USB type-C role switch functionality, not yet described by the binding */
+&usbotg {
+	dr_mode = "peripheral";   /* USB type-C receptable */
+	status = "okay";
+};
+
+&usbphy {
+	status = "okay";
+};
-- 
2.44.0

[PATCH v5 3/4] arm64: dts: allwinner: h700: Add RG35XX-Plus DTS

[Ryan Walklin]

The RG35XX-Plus adds a RTL8221CS SDIO Wifi/BT chip to the RG35XX (2024).

Enabled in this DTS:
- WiFi
- Bluetooth
- Supporting power sequence and GPIOs

Signed-off-by: Ryan Walklin <ryan@testtoast.com>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Jernej Skrabec <jernej.skrabec@gmail.com>
---
Changelog v1..v2:
- Update copyright
- Spaces -> Tabs
- Remove redundant &uart0 node and DTS version tag
- Add GPIO bank comments
- Use generic pwrseq name

Changelog v2..v3:
- Add DTB to Makefile
- Correct Wifi vqmmc-supply to ALDO4
- Move changelog below fold-line

Changelog v3..v4:
- Fix sdio_wifi node indent

Signed-off-by: Ryan Walklin <ryan@testtoast.com>
---
 arch/arm64/boot/dts/allwinner/Makefile        |  1 +
 .../sun50i-h700-anbernic-rg35xx-plus.dts      | 53 +++++++++++++++++++
 2 files changed, 54 insertions(+)
 create mode 100644 arch/arm64/boot/dts/allwinner/sun50i-h700-anbernic-rg35xx-plus.dts

diff --git a/arch/arm64/boot/dts/allwinner/Makefile b/arch/arm64/boot/dts/allwinner/Makefile
index 6f997157968e..4217328b1889 100644
--- a/arch/arm64/boot/dts/allwinner/Makefile
+++ b/arch/arm64/boot/dts/allwinner/Makefile
@@ -48,3 +48,4 @@ dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h618-orangepi-zero2w.dtb
 dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h618-orangepi-zero3.dtb
 dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h618-transpeed-8k618-t.dtb
 dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h700-anbernic-rg35xx-2024.dtb
+dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h700-anbernic-rg35xx-plus.dtb
diff --git a/arch/arm64/boot/dts/allwinner/sun50i-h700-anbernic-rg35xx-plus.dts b/arch/arm64/boot/dts/allwinner/sun50i-h700-anbernic-rg35xx-plus.dts
new file mode 100644
index 000000000000..60a8e4922103
--- /dev/null
+++ b/arch/arm64/boot/dts/allwinner/sun50i-h700-anbernic-rg35xx-plus.dts
@@ -0,0 +1,53 @@
+// SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+/*
+ * Copyright (C) 2024 Ryan Walklin <ryan@testtoast.com>.
+ */
+
+#include "sun50i-h700-anbernic-rg35xx-2024.dts"
+
+/ {
+	model = "Anbernic RG35XX Plus";
+	compatible = "anbernic,rg35xx-plus", "allwinner,sun50i-h700";
+
+	wifi_pwrseq: pwrseq {
+		compatible = "mmc-pwrseq-simple";
+		clocks = <&rtc CLK_OSC32K_FANOUT>;
+		clock-names = "ext_clock";
+		pinctrl-0 = <&x32clk_fanout_pin>;
+		pinctrl-names = "default";
+		post-power-on-delay-ms = <200>;
+		reset-gpios = <&pio 6 18 GPIO_ACTIVE_LOW>; /* PG18 */
+	};
+};
+
+/* SDIO WiFi RTL8821CS */
+&mmc1 {
+	vmmc-supply = <&reg_cldo4>;
+	vqmmc-supply = <&reg_aldo4>;
+	mmc-pwrseq = <&wifi_pwrseq>;
+	bus-width = <4>;
+	non-removable;
+	status = "okay";
+
+	sdio_wifi: wifi@1 {
+		reg = <1>;
+		interrupt-parent = <&pio>;
+		interrupts = <6 15 IRQ_TYPE_LEVEL_LOW>; /* PG15 */
+		interrupt-names = "host-wake";
+	};
+};
+
+/* Bluetooth RTL8821CS */
+&uart1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&uart1_pins>, <&uart1_rts_cts_pins>;
+	uart-has-rtscts;
+	status = "okay";
+
+	bluetooth {
+		compatible = "realtek,rtl8821cs-bt", "realtek,rtl8723bs-bt";
+		device-wake-gpios = <&pio 6 17 GPIO_ACTIVE_HIGH>; /* PG17 */
+		enable-gpios = <&pio 6 19 GPIO_ACTIVE_HIGH>; /* PG19 */
+		host-wake-gpios = <&pio 6 16 GPIO_ACTIVE_HIGH>; /* PG16 */
+	};
+};
-- 
2.44.0

[PATCH v5 4/4] arm64: dts: allwinner: h700: Add RG35XX-H DTS

[Ryan Walklin]

The RG35XX-H adds thumbsticks, a stereo speaker, and a second USB port to
the RG35XX-Plus, and has a horizontal form factor.

Enabled in this DTS:
- Thumbsticks
- Second USB port

Signed-off-by: Ryan Walklin <ryan@testtoast.com>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Jernej Skrabec <jernej.skrabec@gmail.com>
---
Changelog v1..v2:
- Update copyright
- Spaces -> Tabs
- Add GP ADC joystick axes and mux [1]
- Add EHCI/OHCI1 for second USB port and add vbus supply

Changelog v2..v3:
- Add DTB to Makefile
- Remove USB vbus supply
- Remove GPADC joysticks until required patches land [1]
- Move thumbsticks into existing gpio gamepad node
- Move changelog and links below fold-line

Changelog v3..v4:
- Remove redundant USB OTG and PHY nodes.

Changelog v4..v5:
- Remove empty line.

[1]: https://lore.kernel.org/linux-sunxi/20240417170423.20640-1-macroalpha82@gmail.com/T/#t

Signed-off-by: Ryan Walklin <ryan@testtoast.com>
---
 arch/arm64/boot/dts/allwinner/Makefile        |  1 +
 .../sun50i-h700-anbernic-rg35xx-h.dts         | 36 +++++++++++++++++++
 2 files changed, 37 insertions(+)
 create mode 100644 arch/arm64/boot/dts/allwinner/sun50i-h700-anbernic-rg35xx-h.dts

diff --git a/arch/arm64/boot/dts/allwinner/Makefile b/arch/arm64/boot/dts/allwinner/Makefile
index 4217328b1889..c2c871d8b71e 100644
--- a/arch/arm64/boot/dts/allwinner/Makefile
+++ b/arch/arm64/boot/dts/allwinner/Makefile
@@ -49,3 +49,4 @@ dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h618-orangepi-zero3.dtb
 dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h618-transpeed-8k618-t.dtb
 dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h700-anbernic-rg35xx-2024.dtb
 dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h700-anbernic-rg35xx-plus.dtb
+dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h700-anbernic-rg35xx-h.dtb
diff --git a/arch/arm64/boot/dts/allwinner/sun50i-h700-anbernic-rg35xx-h.dts b/arch/arm64/boot/dts/allwinner/sun50i-h700-anbernic-rg35xx-h.dts
new file mode 100644
index 000000000000..63036256917f
--- /dev/null
+++ b/arch/arm64/boot/dts/allwinner/sun50i-h700-anbernic-rg35xx-h.dts
@@ -0,0 +1,36 @@
+// SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+/*
+ * Copyright (C) 2024 Ryan Walklin <ryan@testtoast.com>.
+ * Copyright (C) 2024 Chris Morgan <macroalpha82@gmail.com>.
+ */
+
+#include "sun50i-h700-anbernic-rg35xx-plus.dts"
+
+/ {
+	model = "Anbernic RG35XX H";
+	compatible = "anbernic,rg35xx-h", "allwinner,sun50i-h700";
+};
+
+&gpio_keys_gamepad {
+	button-thumbl {
+		label = "GPIO Thumb Left";
+		gpios = <&pio 4 8 GPIO_ACTIVE_LOW>; /* PE8 */
+		linux,input-type = <EV_KEY>;
+		linux,code = <BTN_THUMBL>;
+	};
+
+	button-thumbr {
+		label = "GPIO Thumb Right";
+		gpios = <&pio 4 9 GPIO_ACTIVE_LOW>; /* PE9 */
+		linux,input-type = <EV_KEY>;
+		linux,code = <BTN_THUMBR>;
+	};
+};
+
+&ehci1 {
+	status = "okay";
+};
+
+&ohci1 {
+	status = "okay";
+};
-- 
2.44.0

Re: [PATCH v5 2/4] arm64: dts: allwinner: h700: Add RG35XX 2024 DTS

[Jernej Škrabec]

Dne petek, 26. april 2024 ob 23:35:10 GMT +2 je Ryan Walklin napisal(a):
> The base model RG35XX (2024) is a handheld gaming device based on an
> Allwinner H700 chip.
> 
> The H700 is a H616 variant (4x ARM Cortex-A53 cores @ 1.5Ghz with Mali G31
> GPU) which exposes RGB LCD and NMI pins.
> 
> Device features:
> - Allwinner H700 @ 1.5GHz
> - 1GB LPDDR4 DRAM
> - X-Powers AXP717 PMIC
> - 3.5" 640x480 RGB LCD
> - Two microSD slots
> - Mini-HDMI out
> - GPIO keypad
> - 3.5mm headphone jack
> - USB-C charging port
> 
> Enabled in this DTS:
> - AXP717 PMIC with RSB serial interface, regulators and NMI interrupt
>   controller
> - Power LED (charge LED on device controlled directly by PMIC)
> - Serial UART (accessible from headers on the board)
> - MMC slots (SD2 appears to have a GPIO-switched regulator for 1.8v
>   low-voltage signalling, this is not yet modeled so a fixed-regulator and
>   3.3v and 1.8v rails from the PMIC are used. A switched regulator will be
>   confirmed and posted in a follow-up patch)
> 
> Signed-off-by: Ryan Walklin <ryan@testtoast.com>

Reviewed-by: Jernej Skrabec <jernej.skrabec@gmail.com>

Best regards,
Jernej

Re: [PATCH v5 2/4] arm64: dts: allwinner: h700: Add RG35XX 2024 DTS

[Jernej Škrabec]

Dne petek, 26. april 2024 ob 23:35:10 GMT +2 je Ryan Walklin napisal(a):
> The base model RG35XX (2024) is a handheld gaming device based on an
> Allwinner H700 chip.
> 
> The H700 is a H616 variant (4x ARM Cortex-A53 cores @ 1.5Ghz with Mali G31
> GPU) which exposes RGB LCD and NMI pins.
> 
> Device features:
> - Allwinner H700 @ 1.5GHz
> - 1GB LPDDR4 DRAM
> - X-Powers AXP717 PMIC
> - 3.5" 640x480 RGB LCD
> - Two microSD slots
> - Mini-HDMI out
> - GPIO keypad
> - 3.5mm headphone jack
> - USB-C charging port
> 
> Enabled in this DTS:
> - AXP717 PMIC with RSB serial interface, regulators and NMI interrupt
>   controller
> - Power LED (charge LED on device controlled directly by PMIC)
> - Serial UART (accessible from headers on the board)
> - MMC slots (SD2 appears to have a GPIO-switched regulator for 1.8v
>   low-voltage signalling, this is not yet modeled so a fixed-regulator and
>   3.3v and 1.8v rails from the PMIC are used. A switched regulator will be
>   confirmed and posted in a follow-up patch)
> 
> Signed-off-by: Ryan Walklin <ryan@testtoast.com>
> ---
> Changelog v1..v2:
> - Update copyright
> - Spaces -> Tabs
> - Add cpufreq support
> - Remove MMC aliases
> - Fix GPIO button and regulator node names
> - Note unused AXP717 regulators
> - Update regulators for SD slots
> - Remove unused I2C3 device
> - Update NMI interrupt controller for AXP717, requires H616 support patch in dt-next [1]
> - Add chassis-type
> - Address USB EHCI/OHCI0 correctly and add usb vbus supply
> - Add PIO vcc-pg-supply
> - Correct boost regulator voltage and name
> 
> Changelog v2..v3:
> - Remove cpufreq support (patch still pending for 6.10, will followup with enablement patch once opp table merged)
> - Add dtb to Makefile
> - Remove unnecessary duplicated PLL regulator
> - Remove unimplemented/not-present drive-vbus feature from AXP717
> - Rename CLDO3 to "vcc-io", inferring function from board testing by Chris Morgan
> - Correct MMC1 vmmc-supply to CLDO3 and MMC2 to CLDO4
> - Reduce DCDC1 "vdd-cpu" supply voltage range to 0.9v-1.1v to match lowest OPP voltage
> - Identify DCDC2 as GPU supply - rename to "vdd-gpu-sys", remove always-on and use fixed 0.94v voltage
> - Fix indentation
> - Correct boot/always-on states and voltages for various regulators from vendor BSP
> - Change USB-OTG mode to "peripheral" and correct comment
> - Correct and add remaining PIO supplies
> - Move volume key GPIOs to separate block to allow key repeat
> - Alphabetically orrder gamepad GPIOs
> - Move changelog and links below fold-line
> - Remove USB 3.3v VCC-USB and VCC-SD2 regulators pending further hardware investigation (to be submitted as subsequent patch)
> - Constrain boost regulator voltage to 5.0v to 5.2v to capture default voltage of 5.126v
> 
> Changelog v3..v4:
> - Cluster USB nodes
> - Do not define voltage range for currently unused CLDO1 (connected to audio codec according to vendor BSP - driver not yet implemented) and ALDO3 (1.8v).
> - Note voltages set for currently unused regulators from vendor BSP in comments to aid identification
> - Remove regulator-boot-on from several regulators where it was not required
> - Fix indentation
> - Add "disable-wp" for SD2 as for SD1 (doesn't make sense for micro-SD)
> - Restore fixed 3.3v regulator for SD2 (vcc_3v3_sd2), which is required for SD2 to function. ALDO1 appears to be the 1.8v supply required for low-voltage UHS-I signalling, however a GPIO pin to switch between the supplies is not yet confirmed (likely PE4) and will be implemented in a subsequent patch.
> 
> Changelog v4..v5:
> - Remove comment referencing vendor BSP node
> - Reorder nodes alphabetically and remove empty lines
> - Add note to commit message about SD2 regulators, rename vcc_3v3_sd2
> 
> [1]: https://git.kernel.org/pub/scm/linux/kernel/git/robh/linux.git/commit/?h=dt/next&id=d47bca77bf3ab475c33b3929c33c80aeb49df35c
> 
> Signed-off-by: Ryan Walklin <ryan@testtoast.com>
> ---
>  arch/arm64/boot/dts/allwinner/Makefile        |   1 +
>  .../sun50i-h700-anbernic-rg35xx-2024.dts      | 346 ++++++++++++++++++
>  2 files changed, 347 insertions(+)
>  create mode 100644 arch/arm64/boot/dts/allwinner/sun50i-h700-anbernic-rg35xx-2024.dts
> 
> diff --git a/arch/arm64/boot/dts/allwinner/Makefile b/arch/arm64/boot/dts/allwinner/Makefile
> index 21149b346a60..6f997157968e 100644
> --- a/arch/arm64/boot/dts/allwinner/Makefile
> +++ b/arch/arm64/boot/dts/allwinner/Makefile
> @@ -47,3 +47,4 @@ dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h618-longanpi-3h.dtb
>  dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h618-orangepi-zero2w.dtb
>  dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h618-orangepi-zero3.dtb
>  dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h618-transpeed-8k618-t.dtb
> +dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h700-anbernic-rg35xx-2024.dtb
> diff --git a/arch/arm64/boot/dts/allwinner/sun50i-h700-anbernic-rg35xx-2024.dts b/arch/arm64/boot/dts/allwinner/sun50i-h700-anbernic-rg35xx-2024.dts
> new file mode 100644
> index 000000000000..b90ffa7785c8
> --- /dev/null
> +++ b/arch/arm64/boot/dts/allwinner/sun50i-h700-anbernic-rg35xx-2024.dts
> @@ -0,0 +1,346 @@
> +// SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
> +/*
> + * Copyright (C) 2024 Ryan Walklin <ryan@testtoast.com>.
> + */
> +
> +/dts-v1/;
> +
> +#include "sun50i-h616.dtsi"
> +
> +#include <dt-bindings/gpio/gpio.h>
> +#include <dt-bindings/input/linux-event-codes.h>
> +#include <dt-bindings/interrupt-controller/arm-gic.h>
> +#include <dt-bindings/leds/common.h>
> +
> +/ {
> +	model = "Anbernic RG35XX 2024";
> +	chassis-type = "handset";
> +	compatible = "anbernic,rg35xx-2024", "allwinner,sun50i-h700";
> +
> +	aliases {
> +		serial0 = &uart0;
> +	};
> +
> +	chosen {
> +		stdout-path = "serial0:115200n8";
> +	};
> +
> +	gpio_keys_gamepad: gpio-keys-gamepad {
> +		compatible = "gpio-keys";
> +
> +		button-a {
> +			label = "Action-Pad A";
> +			gpios = <&pio 0 0 GPIO_ACTIVE_LOW>; /* PA0 */
> +			linux,input-type = <EV_KEY>;
> +			linux,code = <BTN_EAST>;
> +		};
> +
> +		button-b {
> +			label = "Action-Pad B";
> +			gpios = <&pio 0 1 GPIO_ACTIVE_LOW>; /* PA1 */
> +			linux,input-type = <EV_KEY>;
> +			linux,code = <BTN_SOUTH>;
> +		};
> +
> +		button-down {
> +			label = "D-Pad Down";
> +			gpios = <&pio 4 0 GPIO_ACTIVE_LOW>; /* PE0 */
> +			linux,input-type = <EV_KEY>;
> +			linux,code = <BTN_DPAD_DOWN>;
> +		};
> +
> +		button-l1 {
> +			label = "Key L1";
> +			gpios = <&pio 0 10 GPIO_ACTIVE_LOW>; /* PA10 */
> +			linux,input-type = <EV_KEY>;
> +			linux,code = <BTN_TL>;
> +		};
> +
> +		button-l2 {
> +			label = "Key L2";
> +			gpios = <&pio 0 11 GPIO_ACTIVE_LOW>; /* PA11 */
> +			linux,input-type = <EV_KEY>;
> +			linux,code = <BTN_TL2>;
> +		};
> +
> +		button-left {
> +			label = "D-Pad left";
> +			gpios = <&pio 0 8 GPIO_ACTIVE_LOW>; /* PA8 */
> +			linux,input-type = <EV_KEY>;
> +			linux,code = <BTN_DPAD_LEFT>;
> +		};
> +
> +		button-menu {
> +			label = "Key Menu";
> +			gpios = <&pio 4 3 GPIO_ACTIVE_LOW>; /* PE3 */
> +			linux,input-type = <EV_KEY>;
> +			linux,code = <BTN_MODE>;
> +		};
> +
> +		button-r1 {
> +			label = "Key R1";
> +			gpios = <&pio 0 12 GPIO_ACTIVE_LOW>; /* PA12 */
> +			linux,input-type = <EV_KEY>;
> +			linux,code = <BTN_TR>;
> +		};
> +
> +		button-r2 {
> +			label = "Key R2";
> +			gpios = <&pio 0 7 GPIO_ACTIVE_LOW>; /* PA7 */
> +			linux,input-type = <EV_KEY>;
> +			linux,code = <BTN_TR2>;
> +		};
> +
> +		button-right {
> +			label = "D-Pad Right";
> +			gpios = <&pio 0 9 GPIO_ACTIVE_LOW>; /* PA9 */
> +			linux,input-type = <EV_KEY>;
> +			linux,code = <BTN_DPAD_RIGHT>;
> +		};
> +
> +		button-select {
> +			label = "Key Select";
> +			gpios = <&pio 0 5 GPIO_ACTIVE_LOW>; /* PA5 */
> +			linux,input-type = <EV_KEY>;
> +			linux,code = <BTN_SELECT>;
> +		};
> +		button-start {
> +			label = "Key Start";
> +			gpios = <&pio 0 4 GPIO_ACTIVE_LOW>; /* PA4 */
> +			linux,input-type = <EV_KEY>;
> +			linux,code = <BTN_START>;
> +		};
> +
> +		button-up {
> +			label = "D-Pad Up";
> +			gpios = <&pio 0 6 GPIO_ACTIVE_LOW>; /* PA6 */
> +			linux,input-type = <EV_KEY>;
> +			linux,code = <BTN_DPAD_UP>;
> +		};
> +
> +		button-x {
> +			label = "Action-Pad X";
> +			gpios = <&pio 0 3 GPIO_ACTIVE_LOW>; /* PA3 */
> +			linux,input-type = <EV_KEY>;
> +			linux,code = <BTN_NORTH>;
> +		};
> +
> +		button-y {
> +			label = "Action Pad Y";
> +			gpios = <&pio 0 2 GPIO_ACTIVE_LOW>; /* PA2 */
> +			linux,input-type = <EV_KEY>;
> +			linux,code = <BTN_WEST>;
> +		};
> +	};
> +
> +	gpio-keys-volume {
> +		compatible = "gpio-keys";
> +		autorepeat;
> +
> +		button-vol-up {
> +			label = "Key Volume Up";
> +			gpios = <&pio 4 1 GPIO_ACTIVE_LOW>; /* PE1 */
> +			linux,input-type = <EV_KEY>;
> +			linux,code = <KEY_VOLUMEUP>;
> +		};
> +
> +		button-vol-down {
> +			label = "Key Volume Down";
> +			gpios = <&pio 4 2 GPIO_ACTIVE_LOW>; /* PE2 */
> +			linux,input-type = <EV_KEY>;
> +			linux,code = <KEY_VOLUMEDOWN>;
> +		};
> +	};
> +
> +	leds {
> +		compatible = "gpio-leds";
> +
> +		led-0 {
> +			function = LED_FUNCTION_POWER;
> +			color = <LED_COLOR_ID_GREEN>;
> +			gpios = <&pio 8 12 GPIO_ACTIVE_HIGH>; /* PI12 */
> +			default-state = "on";
> +		};
> +	};
> +
> +	reg_vcc5v: regulator-vcc5v { /* USB-C power input */
> +		compatible = "regulator-fixed";
> +		regulator-name = "vcc-5v";
> +		regulator-min-microvolt = <5000000>;
> +		regulator-max-microvolt = <5000000>;
> +	};
> +
> +	vcc_3v3_sd2: regulator-3v3-sd2 { /* GPIO-controlled regulator for SD2 IO */
> +		compatible = "regulator-fixed";
> +		gpio = <&pio 4 4 GPIO_ACTIVE_HIGH>; /* PE4 */
> +		regulator-name = "vcc_3v3_sd2";
> +		regulator-max-microvolt = <3300000>;
> +		regulator-min-microvolt = <3300000>;
> +	};
> +};
> +
> +&cpu0 {
> +	cpu-supply = <&reg_dcdc1>;
> +};
> +
> +&ehci0 {
> +	status = "okay";
> +};
> +
> +&mmc0 {
> +	vmmc-supply = <&reg_cldo3>;
> +	disable-wp;
> +	cd-gpios = <&pio 5 6 GPIO_ACTIVE_LOW>;  /* PF6 */
> +	bus-width = <4>;
> +	status = "okay";
> +};
> +
> +&mmc2 {
> +	vmmc-supply = <&reg_cldo4>;
> +	vqmmc-supply = <&reg_aldo1>;
> +	disable-wp;
> +	cd-gpios = <&pio 4 22 GPIO_ACTIVE_LOW>; /* PE22 */
> +	bus-width = <4>;
> +	status = "okay";
> +};
> +
> +&r_rsb {

Eh, I know I give you my Rb tag, but could you just move this whole node, so
they are all alphabetically sorted?

Best regards,
Jernej

> +	status = "okay";
> +
> +	axp717: pmic@3a3 {
> +		compatible = "x-powers,axp717";
> +		reg = <0x3a3>;
> +		interrupt-controller;
> +		#interrupt-cells = <1>;
> +		interrupt-parent = <&nmi_intc>;
> +		interrupts = <0 IRQ_TYPE_LEVEL_LOW>;
> +
> +		vin1-supply = <&reg_vcc5v>;
> +		vin2-supply = <&reg_vcc5v>;
> +		vin3-supply = <&reg_vcc5v>;
> +		vin4-supply = <&reg_vcc5v>;
> +
> +		regulators {
> +			reg_dcdc1: dcdc1 {
> +				regulator-always-on;
> +				regulator-min-microvolt = <900000>;
> +				regulator-max-microvolt = <1100000>;
> +				regulator-name = "vdd-cpu";
> +			};
> +
> +			reg_dcdc2: dcdc2 {
> +				regulator-always-on;
> +				regulator-min-microvolt = <940000>;
> +				regulator-max-microvolt = <940000>;
> +				regulator-name = "vdd-gpu-sys";
> +			};
> +
> +			reg_dcdc3: dcdc3 {
> +				regulator-always-on;
> +				regulator-min-microvolt = <1100000>;
> +				regulator-max-microvolt = <1100000>;
> +				regulator-name = "vdd-dram";
> +			};
> +
> +			reg_aldo1: aldo1 {
> +				regulator-min-microvolt = <1800000>;
> +				regulator-max-microvolt = <1800000>;
> +				regulator-name = "vcc-sd2";
> +			};
> +
> +			reg_aldo2: aldo2 {
> +				/* 1.8v - unused */
> +			};
> +
> +			reg_aldo3: aldo3 {
> +				/* 1.8v - unused */
> +			};
> +
> +			reg_aldo4: aldo4 {
> +				regulator-min-microvolt = <1800000>;
> +				regulator-max-microvolt = <1800000>;
> +				regulator-name = "vcc-pg";
> +			};
> +
> +			reg_bldo1: bldo1 {
> +				/* 1.8v - unused */
> +			};
> +
> +			reg_bldo2: bldo2 {
> +				regulator-always-on;
> +				regulator-min-microvolt = <1800000>;
> +				regulator-max-microvolt = <1800000>;
> +				regulator-name = "vcc-pll";
> +			};
> +
> +			reg_bldo3: bldo3 {
> +				/* 2.8v - unused */
> +			};
> +
> +			reg_bldo4: bldo4 {
> +				/* 1.2v - unused */
> +			};
> +
> +			reg_cldo1: cldo1 {
> +				/* 3.3v - audio codec - not yet implemented */
> +			};
> +
> +			reg_cldo2: cldo2 {
> +				/* 3.3v - unused */
> +			};
> +
> +			reg_cldo3: cldo3 {
> +				regulator-always-on;
> +				regulator-min-microvolt = <3300000>;
> +				regulator-max-microvolt = <3300000>;
> +				regulator-name = "vcc-io";
> +			};
> +
> +			reg_cldo4: cldo4 {
> +				regulator-min-microvolt = <3300000>;
> +				regulator-max-microvolt = <3300000>;
> +				regulator-name = "vcc-wifi";
> +			};
> +
> +			reg_boost: boost {
> +				regulator-min-microvolt = <5000000>;
> +				regulator-max-microvolt = <5200000>;
> +				regulator-name = "boost";
> +			};
> +
> +			reg_cpusldo: cpusldo {
> +				/* unused */
> +			};
> +		};
> +	};
> +};
> +
> +&ohci0 {
> +	status = "okay";
> +};
> +
> +&pio {
> +	vcc-pa-supply = <&reg_cldo3>;
> +	vcc-pc-supply = <&reg_cldo3>;
> +	vcc-pe-supply = <&reg_cldo3>;
> +	vcc-pf-supply = <&reg_cldo3>;
> +	vcc-pg-supply = <&reg_aldo4>;
> +	vcc-ph-supply = <&reg_cldo3>;
> +	vcc-pi-supply = <&reg_cldo3>;
> +};
> +
> +&uart0 {
> +	pinctrl-names = "default";
> +	pinctrl-0 = <&uart0_ph_pins>;
> +	status = "okay";
> +};
> +
> +/* the AXP717 has USB type-C role switch functionality, not yet described by the binding */
> +&usbotg {
> +	dr_mode = "peripheral";   /* USB type-C receptable */
> +	status = "okay";
> +};
> +
> +&usbphy {
> +	status = "okay";
> +};
>