* [PATCH v2 1/8] arm64: zynqmp: Use ethernet-phy as node name for ethernet phys
2020-01-09 13:52 [PATCH v2 0/8] arm64: zynqmp: Various DT fixes Michal Simek
@ 2020-01-09 13:52 ` Michal Simek
2020-01-09 13:52 ` [PATCH v2 2/8] arm64: zynqmp: Remove addition number in node name Michal Simek
` (7 subsequent siblings)
8 siblings, 0 replies; 10+ messages in thread
From: Michal Simek @ 2020-01-09 13:52 UTC (permalink / raw)
To: linux-arm-kernel, git
Cc: Anurag Kumar Vulisha, Harini Katakam, Mark Rutland, Rajan Vaja,
Rob Herring, Venkatesh Yadav Abbarapu, devicetree, linux-kernel
Ethernet phys based on devicetree specification should be using
ethernet-phy@ node name instead of pure phy@.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
---
Changes in v2:
- Add missing patch
arch/arm64/boot/dts/xilinx/zynqmp-zc1751-xm015-dc1.dts | 2 +-
arch/arm64/boot/dts/xilinx/zynqmp-zc1751-xm016-dc2.dts | 2 +-
arch/arm64/boot/dts/xilinx/zynqmp-zc1751-xm017-dc3.dts | 2 +-
arch/arm64/boot/dts/xilinx/zynqmp-zc1751-xm019-dc5.dts | 2 +-
arch/arm64/boot/dts/xilinx/zynqmp-zcu102-revA.dts | 2 +-
arch/arm64/boot/dts/xilinx/zynqmp-zcu102-revB.dts | 4 ++--
arch/arm64/boot/dts/xilinx/zynqmp-zcu104-revA.dts | 2 +-
arch/arm64/boot/dts/xilinx/zynqmp-zcu106-revA.dts | 2 +-
arch/arm64/boot/dts/xilinx/zynqmp-zcu111-revA.dts | 2 +-
9 files changed, 10 insertions(+), 10 deletions(-)
diff --git a/arch/arm64/boot/dts/xilinx/zynqmp-zc1751-xm015-dc1.dts b/arch/arm64/boot/dts/xilinx/zynqmp-zc1751-xm015-dc1.dts
index 3542d92735cb..69f6e4610739 100644
--- a/arch/arm64/boot/dts/xilinx/zynqmp-zc1751-xm015-dc1.dts
+++ b/arch/arm64/boot/dts/xilinx/zynqmp-zc1751-xm015-dc1.dts
@@ -73,7 +73,7 @@ &gem3 {
status = "okay";
phy-handle = <&phy0>;
phy-mode = "rgmii-id";
- phy0: phy@0 {
+ phy0: ethernet-phy@0 {
reg = <0>;
};
};
diff --git a/arch/arm64/boot/dts/xilinx/zynqmp-zc1751-xm016-dc2.dts b/arch/arm64/boot/dts/xilinx/zynqmp-zc1751-xm016-dc2.dts
index e5d83a4aca07..b75235ae7d30 100644
--- a/arch/arm64/boot/dts/xilinx/zynqmp-zc1751-xm016-dc2.dts
+++ b/arch/arm64/boot/dts/xilinx/zynqmp-zc1751-xm016-dc2.dts
@@ -84,7 +84,7 @@ &gem2 {
status = "okay";
phy-handle = <&phy0>;
phy-mode = "rgmii-id";
- phy0: phy@5 {
+ phy0: ethernet-phy@5 {
reg = <5>;
ti,rx-internal-delay = <0x8>;
ti,tx-internal-delay = <0xa>;
diff --git a/arch/arm64/boot/dts/xilinx/zynqmp-zc1751-xm017-dc3.dts b/arch/arm64/boot/dts/xilinx/zynqmp-zc1751-xm017-dc3.dts
index 3750690925ad..4ea6ef5a7f2b 100644
--- a/arch/arm64/boot/dts/xilinx/zynqmp-zc1751-xm017-dc3.dts
+++ b/arch/arm64/boot/dts/xilinx/zynqmp-zc1751-xm017-dc3.dts
@@ -73,7 +73,7 @@ &gem0 {
status = "okay";
phy-handle = <&phy0>;
phy-mode = "rgmii-id";
- phy0: phy@0 { /* VSC8211 */
+ phy0: ethernet-phy@0 { /* VSC8211 */
reg = <0>;
};
};
diff --git a/arch/arm64/boot/dts/xilinx/zynqmp-zc1751-xm019-dc5.dts b/arch/arm64/boot/dts/xilinx/zynqmp-zc1751-xm019-dc5.dts
index 9a894e6db6ba..41934e3525c6 100644
--- a/arch/arm64/boot/dts/xilinx/zynqmp-zc1751-xm019-dc5.dts
+++ b/arch/arm64/boot/dts/xilinx/zynqmp-zc1751-xm019-dc5.dts
@@ -74,7 +74,7 @@ &gem1 {
status = "okay";
phy-handle = <&phy0>;
phy-mode = "rgmii-id";
- phy0: phy@0 {
+ phy0: ethernet-phy@0 {
reg = <0>;
};
};
diff --git a/arch/arm64/boot/dts/xilinx/zynqmp-zcu102-revA.dts b/arch/arm64/boot/dts/xilinx/zynqmp-zcu102-revA.dts
index d92f617f0b9d..7c6b538490f8 100644
--- a/arch/arm64/boot/dts/xilinx/zynqmp-zcu102-revA.dts
+++ b/arch/arm64/boot/dts/xilinx/zynqmp-zcu102-revA.dts
@@ -105,7 +105,7 @@ &gem3 {
status = "okay";
phy-handle = <&phy0>;
phy-mode = "rgmii-id";
- phy0: phy@21 {
+ phy0: ethernet-phy@21 {
reg = <21>;
ti,rx-internal-delay = <0x8>;
ti,tx-internal-delay = <0xa>;
diff --git a/arch/arm64/boot/dts/xilinx/zynqmp-zcu102-revB.dts b/arch/arm64/boot/dts/xilinx/zynqmp-zcu102-revB.dts
index 1780ed237daf..d9ad8a4b20d3 100644
--- a/arch/arm64/boot/dts/xilinx/zynqmp-zcu102-revB.dts
+++ b/arch/arm64/boot/dts/xilinx/zynqmp-zcu102-revB.dts
@@ -16,7 +16,7 @@ / {
&gem3 {
phy-handle = <&phyc>;
- phyc: phy@c {
+ phyc: ethernet-phy@c {
reg = <0xc>;
ti,rx-internal-delay = <0x8>;
ti,tx-internal-delay = <0xa>;
@@ -24,7 +24,7 @@ phyc: phy@c {
ti,dp83867-rxctrl-strap-quirk;
};
/* Cleanup from RevA */
- /delete-node/ phy@21;
+ /delete-node/ ethernet-phy@21;
};
/* Fix collision with u61 */
diff --git a/arch/arm64/boot/dts/xilinx/zynqmp-zcu104-revA.dts b/arch/arm64/boot/dts/xilinx/zynqmp-zcu104-revA.dts
index cfb054e46723..2d71b4431cce 100644
--- a/arch/arm64/boot/dts/xilinx/zynqmp-zcu104-revA.dts
+++ b/arch/arm64/boot/dts/xilinx/zynqmp-zcu104-revA.dts
@@ -50,7 +50,7 @@ &gem3 {
status = "okay";
phy-handle = <&phy0>;
phy-mode = "rgmii-id";
- phy0: phy@c {
+ phy0: ethernet-phy@c {
reg = <0xc>;
ti,rx-internal-delay = <0x8>;
ti,tx-internal-delay = <0xa>;
diff --git a/arch/arm64/boot/dts/xilinx/zynqmp-zcu106-revA.dts b/arch/arm64/boot/dts/xilinx/zynqmp-zcu106-revA.dts
index ea2dcbe9effd..ae62fe4287c2 100644
--- a/arch/arm64/boot/dts/xilinx/zynqmp-zcu106-revA.dts
+++ b/arch/arm64/boot/dts/xilinx/zynqmp-zcu106-revA.dts
@@ -106,7 +106,7 @@ &gem3 {
status = "okay";
phy-handle = <&phy0>;
phy-mode = "rgmii-id";
- phy0: phy@c {
+ phy0: ethernet-phy@c {
reg = <0xc>;
ti,rx-internal-delay = <0x8>;
ti,tx-internal-delay = <0xa>;
diff --git a/arch/arm64/boot/dts/xilinx/zynqmp-zcu111-revA.dts b/arch/arm64/boot/dts/xilinx/zynqmp-zcu111-revA.dts
index d656eb8b3040..b3c29947d6b3 100644
--- a/arch/arm64/boot/dts/xilinx/zynqmp-zcu111-revA.dts
+++ b/arch/arm64/boot/dts/xilinx/zynqmp-zcu111-revA.dts
@@ -101,7 +101,7 @@ &gem3 {
status = "okay";
phy-handle = <&phy0>;
phy-mode = "rgmii-id";
- phy0: phy@c {
+ phy0: ethernet-phy@c {
reg = <0xc>;
ti,rx-internal-delay = <0x8>;
ti,tx-internal-delay = <0xa>;
--
2.24.0
^ permalink raw reply related [flat|nested] 10+ messages in thread* [PATCH v2 2/8] arm64: zynqmp: Remove addition number in node name
2020-01-09 13:52 [PATCH v2 0/8] arm64: zynqmp: Various DT fixes Michal Simek
2020-01-09 13:52 ` [PATCH v2 1/8] arm64: zynqmp: Use ethernet-phy as node name for ethernet phys Michal Simek
@ 2020-01-09 13:52 ` Michal Simek
2020-01-09 13:52 ` [PATCH v2 3/8] arm64: zynqmp: Fix address for tca6416_u97 chip on zcu104 Michal Simek
` (6 subsequent siblings)
8 siblings, 0 replies; 10+ messages in thread
From: Michal Simek @ 2020-01-09 13:52 UTC (permalink / raw)
To: linux-arm-kernel, git
Cc: Anurag Kumar Vulisha, Harini Katakam, Mark Rutland, Rajan Vaja,
Rob Herring, devicetree, linux-kernel
This change is coming from mainline review that's why this patch is
sync.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
---
Changes in v2:
- Add missing patch
arch/arm64/boot/dts/xilinx/zynqmp-zc1751-xm016-dc2.dts | 4 ++--
1 file changed, 2 insertions(+), 2 deletions(-)
diff --git a/arch/arm64/boot/dts/xilinx/zynqmp-zc1751-xm016-dc2.dts b/arch/arm64/boot/dts/xilinx/zynqmp-zc1751-xm016-dc2.dts
index b75235ae7d30..4a86efa32d68 100644
--- a/arch/arm64/boot/dts/xilinx/zynqmp-zc1751-xm016-dc2.dts
+++ b/arch/arm64/boot/dts/xilinx/zynqmp-zc1751-xm016-dc2.dts
@@ -123,7 +123,7 @@ &spi0 {
status = "okay";
num-cs = <1>;
- spi0_flash0: flash0@0 {
+ spi0_flash0: flash@0 {
#address-cells = <1>;
#size-cells = <1>;
compatible = "sst,sst25wf080", "jedec,spi-nor";
@@ -141,7 +141,7 @@ &spi1 {
status = "okay";
num-cs = <1>;
- spi1_flash0: flash0@0 {
+ spi1_flash0: flash@0 {
#address-cells = <1>;
#size-cells = <1>;
compatible = "atmel,at45db041e", "atmel,at45", "atmel,dataflash";
--
2.24.0
^ permalink raw reply related [flat|nested] 10+ messages in thread* [PATCH v2 3/8] arm64: zynqmp: Fix address for tca6416_u97 chip on zcu104
2020-01-09 13:52 [PATCH v2 0/8] arm64: zynqmp: Various DT fixes Michal Simek
2020-01-09 13:52 ` [PATCH v2 1/8] arm64: zynqmp: Use ethernet-phy as node name for ethernet phys Michal Simek
2020-01-09 13:52 ` [PATCH v2 2/8] arm64: zynqmp: Remove addition number in node name Michal Simek
@ 2020-01-09 13:52 ` Michal Simek
2020-01-09 13:52 ` [PATCH v2 4/8] arm64: zynqmp: Turn comment to gpio-line-names Michal Simek
` (5 subsequent siblings)
8 siblings, 0 replies; 10+ messages in thread
From: Michal Simek @ 2020-01-09 13:52 UTC (permalink / raw)
To: linux-arm-kernel, git
Cc: Anurag Kumar Vulisha, Harini Katakam, Mark Rutland, Rajan Vaja,
Rob Herring, devicetree, linux-kernel
I2c address is not 0x21 but 0x20.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
---
Changes in v2: None
arch/arm64/boot/dts/xilinx/zynqmp-zcu104-revA.dts | 4 ++--
1 file changed, 2 insertions(+), 2 deletions(-)
diff --git a/arch/arm64/boot/dts/xilinx/zynqmp-zcu104-revA.dts b/arch/arm64/boot/dts/xilinx/zynqmp-zcu104-revA.dts
index 2d71b4431cce..7a4614e3f5fa 100644
--- a/arch/arm64/boot/dts/xilinx/zynqmp-zcu104-revA.dts
+++ b/arch/arm64/boot/dts/xilinx/zynqmp-zcu104-revA.dts
@@ -118,9 +118,9 @@ i2c@4 {
#address-cells = <1>;
#size-cells = <0>;
reg = <4>;
- tca6416_u97: gpio@21 {
+ tca6416_u97: gpio@20 {
compatible = "ti,tca6416";
- reg = <0x21>;
+ reg = <0x20>;
gpio-controller;
#gpio-cells = <2>;
/*
--
2.24.0
^ permalink raw reply related [flat|nested] 10+ messages in thread* [PATCH v2 4/8] arm64: zynqmp: Turn comment to gpio-line-names
2020-01-09 13:52 [PATCH v2 0/8] arm64: zynqmp: Various DT fixes Michal Simek
` (2 preceding siblings ...)
2020-01-09 13:52 ` [PATCH v2 3/8] arm64: zynqmp: Fix address for tca6416_u97 chip on zcu104 Michal Simek
@ 2020-01-09 13:52 ` Michal Simek
2020-01-09 13:52 ` [PATCH v2 5/8] arm64: zynqmp: Setup clock-output-names for si570 chips Michal Simek
` (4 subsequent siblings)
8 siblings, 0 replies; 10+ messages in thread
From: Michal Simek @ 2020-01-09 13:52 UTC (permalink / raw)
To: linux-arm-kernel, git
Cc: Anurag Kumar Vulisha, Harini Katakam, Mark Rutland, Rajan Vaja,
Rob Herring, devicetree, linux-kernel
Label gpio lines properly.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
---
Changes in v2: None
.../boot/dts/xilinx/zynqmp-zcu102-revA.dts | 43 ++++---------------
1 file changed, 9 insertions(+), 34 deletions(-)
diff --git a/arch/arm64/boot/dts/xilinx/zynqmp-zcu102-revA.dts b/arch/arm64/boot/dts/xilinx/zynqmp-zcu102-revA.dts
index 7c6b538490f8..c96e8416fa7e 100644
--- a/arch/arm64/boot/dts/xilinx/zynqmp-zcu102-revA.dts
+++ b/arch/arm64/boot/dts/xilinx/zynqmp-zcu102-revA.dts
@@ -125,21 +125,11 @@ &i2c0 {
tca6416_u97: gpio@20 {
compatible = "ti,tca6416";
reg = <0x20>;
- gpio-controller;
+ gpio-controller; /* IRQ not connected */
#gpio-cells = <2>;
- /*
- * IRQ not connected
- * Lines:
- * 0 - PS_GTR_LAN_SEL0
- * 1 - PS_GTR_LAN_SEL1
- * 2 - PS_GTR_LAN_SEL2
- * 3 - PS_GTR_LAN_SEL3
- * 4 - PCI_CLK_DIR_SEL
- * 5 - IIC_MUX_RESET_B
- * 6 - GEM3_EXP_RESET_B
- * 7, 10 - 17 - not connected
- */
-
+ gpio-line-names = "PS_GTR_LAN_SEL0", "PS_GTR_LAN_SEL1", "PS_GTR_LAN_SEL2", "PS_GTR_LAN_SEL3",
+ "PCI_CLK_DIR_SEL", "IIC_MUX_RESET_B", "GEM3_EXP_RESET_B",
+ "", "", "", "", "", "", "", "", "";
gtr-sel0 {
gpio-hog;
gpios = <0 0>;
@@ -169,27 +159,12 @@ gtr-sel3 {
tca6416_u61: gpio@21 {
compatible = "ti,tca6416";
reg = <0x21>;
- gpio-controller;
+ gpio-controller; /* IRQ not connected */
#gpio-cells = <2>;
- /*
- * IRQ not connected
- * Lines:
- * 0 - VCCPSPLL_EN
- * 1 - MGTRAVCC_EN
- * 2 - MGTRAVTT_EN
- * 3 - VCCPSDDRPLL_EN
- * 4 - MIO26_PMU_INPUT_LS
- * 5 - PL_PMBUS_ALERT
- * 6 - PS_PMBUS_ALERT
- * 7 - MAXIM_PMBUS_ALERT
- * 10 - PL_DDR4_VTERM_EN
- * 11 - PL_DDR4_VPP_2V5_EN
- * 12 - PS_DIMM_VDDQ_TO_PSVCCO_ON
- * 13 - PS_DIMM_SUSPEND_EN
- * 14 - PS_DDR4_VTERM_EN
- * 15 - PS_DDR4_VPP_2V5_EN
- * 16 - 17 - not connected
- */
+ gpio-line-names = "VCCPSPLL_EN", "MGTRAVCC_EN", "MGTRAVTT_EN", "VCCPSDDRPLL_EN", "MIO26_PMU_INPUT_LS",
+ "PL_PMBUS_ALERT", "PS_PMBUS_ALERT", "MAXIM_PMBUS_ALERT", "PL_DDR4_VTERM_EN",
+ "PL_DDR4_VPP_2V5_EN", "PS_DIMM_VDDQ_TO_PSVCCO_ON", "PS_DIMM_SUSPEND_EN",
+ "PS_DDR4_VTERM_EN", "PS_DDR4_VPP_2V5_EN", "", "";
};
i2c-mux@75 { /* u60 */
--
2.24.0
^ permalink raw reply related [flat|nested] 10+ messages in thread* [PATCH v2 5/8] arm64: zynqmp: Setup clock-output-names for si570 chips
2020-01-09 13:52 [PATCH v2 0/8] arm64: zynqmp: Various DT fixes Michal Simek
` (3 preceding siblings ...)
2020-01-09 13:52 ` [PATCH v2 4/8] arm64: zynqmp: Turn comment to gpio-line-names Michal Simek
@ 2020-01-09 13:52 ` Michal Simek
2020-01-09 13:52 ` [PATCH v2 6/8] arm64: zynqmp: Fix the si570 clock frequency on zcu111 Michal Simek
` (3 subsequent siblings)
8 siblings, 0 replies; 10+ messages in thread
From: Michal Simek @ 2020-01-09 13:52 UTC (permalink / raw)
To: linux-arm-kernel, git
Cc: Anurag Kumar Vulisha, Harini Katakam, Mark Rutland, Rajan Vaja,
Rob Herring, Venkatesh Yadav Abbarapu, devicetree, linux-kernel
If there are more instances of si570 clock-output-names property
should be used for differentiation of clock output.
The patch is adding this optional properties for all zynqmp boards with
si570 chip.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
---
Changes in v2: None
arch/arm64/boot/dts/xilinx/zynqmp-zcu102-revA.dts | 2 ++
arch/arm64/boot/dts/xilinx/zynqmp-zcu106-revA.dts | 2 ++
arch/arm64/boot/dts/xilinx/zynqmp-zcu111-revA.dts | 2 ++
3 files changed, 6 insertions(+)
diff --git a/arch/arm64/boot/dts/xilinx/zynqmp-zcu102-revA.dts b/arch/arm64/boot/dts/xilinx/zynqmp-zcu102-revA.dts
index c96e8416fa7e..845671447f60 100644
--- a/arch/arm64/boot/dts/xilinx/zynqmp-zcu102-revA.dts
+++ b/arch/arm64/boot/dts/xilinx/zynqmp-zcu102-revA.dts
@@ -389,6 +389,7 @@ si570_1: clock-generator@5d { /* USER SI570 - u42 */
temperature-stability = <50>;
factory-fout = <300000000>;
clock-frequency = <300000000>;
+ clock-output-names = "si570_user";
};
};
i2c@3 {
@@ -402,6 +403,7 @@ si570_2: clock-generator@5d { /* USER MGT SI570 - u56 */
temperature-stability = <50>; /* copy from zc702 */
factory-fout = <156250000>;
clock-frequency = <148500000>;
+ clock-output-names = "si570_mgt";
};
};
i2c@4 {
diff --git a/arch/arm64/boot/dts/xilinx/zynqmp-zcu106-revA.dts b/arch/arm64/boot/dts/xilinx/zynqmp-zcu106-revA.dts
index ae62fe4287c2..822de6f04725 100644
--- a/arch/arm64/boot/dts/xilinx/zynqmp-zcu106-revA.dts
+++ b/arch/arm64/boot/dts/xilinx/zynqmp-zcu106-revA.dts
@@ -388,6 +388,7 @@ si570_1: clock-generator@5d { /* USER SI570 - u42 */
temperature-stability = <50>;
factory-fout = <300000000>;
clock-frequency = <300000000>;
+ clock-output-names = "si570_user";
};
};
i2c@3 {
@@ -401,6 +402,7 @@ si570_2: clock-generator@5d { /* USER MGT SI570 - u56 */
temperature-stability = <50>; /* copy from zc702 */
factory-fout = <156250000>;
clock-frequency = <148500000>;
+ clock-output-names = "si570_mgt";
};
};
i2c@4 {
diff --git a/arch/arm64/boot/dts/xilinx/zynqmp-zcu111-revA.dts b/arch/arm64/boot/dts/xilinx/zynqmp-zcu111-revA.dts
index b3c29947d6b3..022c732005ee 100644
--- a/arch/arm64/boot/dts/xilinx/zynqmp-zcu111-revA.dts
+++ b/arch/arm64/boot/dts/xilinx/zynqmp-zcu111-revA.dts
@@ -304,6 +304,7 @@ si570_1: clock-generator@5d { /* USER SI570 - u47 */
temperature-stability = <50>;
factory-fout = <300000000>;
clock-frequency = <300000000>;
+ clock-output-names = "si570_user";
};
};
i2c@3 {
@@ -317,6 +318,7 @@ si570_2: clock-generator@5d { /* USER MGT SI570 - u49 */
temperature-stability = <50>;
factory-fout = <156250000>;
clock-frequency = <148500000>;
+ clock-output-names = "si570_mgt";
};
};
i2c@4 {
--
2.24.0
^ permalink raw reply related [flat|nested] 10+ messages in thread* [PATCH v2 6/8] arm64: zynqmp: Fix the si570 clock frequency on zcu111
2020-01-09 13:52 [PATCH v2 0/8] arm64: zynqmp: Various DT fixes Michal Simek
` (4 preceding siblings ...)
2020-01-09 13:52 ` [PATCH v2 5/8] arm64: zynqmp: Setup clock-output-names for si570 chips Michal Simek
@ 2020-01-09 13:52 ` Michal Simek
2020-01-09 13:52 ` [PATCH v2 7/8] arm64: zynqmp: Remove broken-cd from zcu100-revC Michal Simek
` (2 subsequent siblings)
8 siblings, 0 replies; 10+ messages in thread
From: Michal Simek @ 2020-01-09 13:52 UTC (permalink / raw)
To: linux-arm-kernel, git
Cc: Venkatesh Yadav Abbarapu, Anurag Kumar Vulisha, Harini Katakam,
Mark Rutland, Rajan Vaja, Rob Herring, devicetree, linux-kernel
From: Venkatesh Yadav Abbarapu <venkatesh.abbarapu@xilinx.com>
The si570 clock frequency should be 156.25MHz as per datasheet.
Signed-off-by: Venkatesh Yadav Abbarapu <venkatesh.abbarapu@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
---
Changes in v2: None
arch/arm64/boot/dts/xilinx/zynqmp-zcu111-revA.dts | 2 +-
1 file changed, 1 insertion(+), 1 deletion(-)
diff --git a/arch/arm64/boot/dts/xilinx/zynqmp-zcu111-revA.dts b/arch/arm64/boot/dts/xilinx/zynqmp-zcu111-revA.dts
index 022c732005ee..cb2e46833a7b 100644
--- a/arch/arm64/boot/dts/xilinx/zynqmp-zcu111-revA.dts
+++ b/arch/arm64/boot/dts/xilinx/zynqmp-zcu111-revA.dts
@@ -317,7 +317,7 @@ si570_2: clock-generator@5d { /* USER MGT SI570 - u49 */
reg = <0x5d>;
temperature-stability = <50>;
factory-fout = <156250000>;
- clock-frequency = <148500000>;
+ clock-frequency = <156250000>;
clock-output-names = "si570_mgt";
};
};
--
2.24.0
^ permalink raw reply related [flat|nested] 10+ messages in thread* [PATCH v2 7/8] arm64: zynqmp: Remove broken-cd from zcu100-revC
2020-01-09 13:52 [PATCH v2 0/8] arm64: zynqmp: Various DT fixes Michal Simek
` (5 preceding siblings ...)
2020-01-09 13:52 ` [PATCH v2 6/8] arm64: zynqmp: Fix the si570 clock frequency on zcu111 Michal Simek
@ 2020-01-09 13:52 ` Michal Simek
2020-01-09 13:52 ` [PATCH v2 8/8] arm64: zynqmp: Setup default number of chipselects for zcu100 Michal Simek
2020-01-21 9:51 ` [PATCH v2 0/8] arm64: zynqmp: Various DT fixes Michal Simek
8 siblings, 0 replies; 10+ messages in thread
From: Michal Simek @ 2020-01-09 13:52 UTC (permalink / raw)
To: linux-arm-kernel, git
Cc: Anurag Kumar Vulisha, Jan Kiszka, Mark Rutland, Rajan Vaja,
Rob Herring, Ulf Hansson, devicetree, linux-kernel
Card detect bit was broken on revA and it is working fine with revC
board that's why this property can be removed.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
---
Changes in v2: None
arch/arm64/boot/dts/xilinx/zynqmp-zcu100-revC.dts | 1 -
1 file changed, 1 deletion(-)
diff --git a/arch/arm64/boot/dts/xilinx/zynqmp-zcu100-revC.dts b/arch/arm64/boot/dts/xilinx/zynqmp-zcu100-revC.dts
index dd60f7d85cc8..2b3757dd74cc 100644
--- a/arch/arm64/boot/dts/xilinx/zynqmp-zcu100-revC.dts
+++ b/arch/arm64/boot/dts/xilinx/zynqmp-zcu100-revC.dts
@@ -226,7 +226,6 @@ &rtc {
&sdhci0 {
status = "okay";
no-1-8-v;
- broken-cd; /* CD has to be enabled by default */
disable-wp;
};
--
2.24.0
^ permalink raw reply related [flat|nested] 10+ messages in thread* [PATCH v2 8/8] arm64: zynqmp: Setup default number of chipselects for zcu100
2020-01-09 13:52 [PATCH v2 0/8] arm64: zynqmp: Various DT fixes Michal Simek
` (6 preceding siblings ...)
2020-01-09 13:52 ` [PATCH v2 7/8] arm64: zynqmp: Remove broken-cd from zcu100-revC Michal Simek
@ 2020-01-09 13:52 ` Michal Simek
2020-01-21 9:51 ` [PATCH v2 0/8] arm64: zynqmp: Various DT fixes Michal Simek
8 siblings, 0 replies; 10+ messages in thread
From: Michal Simek @ 2020-01-09 13:52 UTC (permalink / raw)
To: linux-arm-kernel, git
Cc: Anurag Kumar Vulisha, Jan Kiszka, Mark Rutland, Rajan Vaja,
Rob Herring, Ulf Hansson, devicetree, linux-kernel
There is only one chipselect on each connector.
Define it directly in board dts file.
There should be an option to use more chipselects via gpios.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
---
Changes in v2: None
arch/arm64/boot/dts/xilinx/zynqmp-zcu100-revC.dts | 2 ++
1 file changed, 2 insertions(+)
diff --git a/arch/arm64/boot/dts/xilinx/zynqmp-zcu100-revC.dts b/arch/arm64/boot/dts/xilinx/zynqmp-zcu100-revC.dts
index 2b3757dd74cc..a109e82982ae 100644
--- a/arch/arm64/boot/dts/xilinx/zynqmp-zcu100-revC.dts
+++ b/arch/arm64/boot/dts/xilinx/zynqmp-zcu100-revC.dts
@@ -250,11 +250,13 @@ wlcore: wifi@2 {
&spi0 { /* Low Speed connector */
status = "okay";
label = "LS-SPI0";
+ num-cs = <1>;
};
&spi1 { /* High Speed connector */
status = "okay";
label = "HS-SPI1";
+ num-cs = <1>;
};
&uart0 {
--
2.24.0
^ permalink raw reply related [flat|nested] 10+ messages in thread* Re: [PATCH v2 0/8] arm64: zynqmp: Various DT fixes
2020-01-09 13:52 [PATCH v2 0/8] arm64: zynqmp: Various DT fixes Michal Simek
` (7 preceding siblings ...)
2020-01-09 13:52 ` [PATCH v2 8/8] arm64: zynqmp: Setup default number of chipselects for zcu100 Michal Simek
@ 2020-01-21 9:51 ` Michal Simek
8 siblings, 0 replies; 10+ messages in thread
From: Michal Simek @ 2020-01-21 9:51 UTC (permalink / raw)
To: linux-arm, git
Cc: Anurag Kumar Vulisha, Harini Katakam, Jan Kiszka, Mark Rutland,
Rajan Vaja, Rob Herring, Ulf Hansson, Venkatesh Yadav Abbarapu,
DTML, LKML
čt 9. 1. 2020 v 14:52 odesílatel Michal Simek <michal.simek@xilinx.com> napsal:
>
> Hi,
>
> I am sending various DT fixes which have been found over the xilinx
> release.
> 1-2 patches are fixing reported description issues
> 3-8 patches are actual fixes.
>
> Thanks,
> Michal
>
> Changes in v2:
> - Add missing patch
> - Add missing patch
>
> Michal Simek (7):
> arm64: zynqmp: Use ethernet-phy as node name for ethernet phys
> arm64: zynqmp: Remove addition number in node name
> arm64: zynqmp: Fix address for tca6416_u97 chip on zcu104
> arm64: zynqmp: Turn comment to gpio-line-names
> arm64: zynqmp: Setup clock-output-names for si570 chips
> arm64: zynqmp: Remove broken-cd from zcu100-revC
> arm64: zynqmp: Setup default number of chipselects for zcu100
>
> Venkatesh Yadav Abbarapu (1):
> arm64: zynqmp: Fix the si570 clock frequency on zcu111
>
> .../dts/xilinx/zynqmp-zc1751-xm015-dc1.dts | 2 +-
> .../dts/xilinx/zynqmp-zc1751-xm016-dc2.dts | 6 +--
> .../dts/xilinx/zynqmp-zc1751-xm017-dc3.dts | 2 +-
> .../dts/xilinx/zynqmp-zc1751-xm019-dc5.dts | 2 +-
> .../boot/dts/xilinx/zynqmp-zcu100-revC.dts | 3 +-
> .../boot/dts/xilinx/zynqmp-zcu102-revA.dts | 47 +++++--------------
> .../boot/dts/xilinx/zynqmp-zcu102-revB.dts | 4 +-
> .../boot/dts/xilinx/zynqmp-zcu104-revA.dts | 6 +--
> .../boot/dts/xilinx/zynqmp-zcu106-revA.dts | 4 +-
> .../boot/dts/xilinx/zynqmp-zcu111-revA.dts | 6 ++-
> 10 files changed, 32 insertions(+), 50 deletions(-)
>
> --
> 2.24.0
>
Applied all.
Thanks,
Michal
--
Michal Simek, Ing. (M.Eng), OpenPGP -> KeyID: FE3D1F91
w: www.monstr.eu p: +42-0-721842854
Maintainer of Linux kernel - Xilinx Microblaze
Maintainer of Linux kernel - Xilinx Zynq ARM and ZynqMP ARM64 SoCs
U-Boot custodian - Xilinx Microblaze/Zynq/ZynqMP/Versal SoCs
^ permalink raw reply [flat|nested] 10+ messages in thread