Re: [PATCH 7/7] ARM: dts: r8a7742-iwg21d-q7: Add LCD support

["Lad, Prabhakar" <prabhakar.csengg@gmail.com>]

Hi Laurent,

Thank you for the review.


On Sat, Aug 8, 2020 at 10:23 PM Laurent Pinchart
<laurent.pinchart@ideasonboard.com> wrote:
>
> Hi Prabhakar,
>
> Thank you for the patch.
>
> On Fri, Aug 07, 2020 at 06:49:54PM +0100, Lad Prabhakar wrote:
> > The iwg21d comes with a 7" capacitive touch screen, therefore
> > add support for it.
>
> I can't review most of this properly as I don't have access to the
> schematics. Is there a way to get it ?
>
I'll check with Chris, how we could get the schematics for you.

> > Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
> > Reviewed-by: Marian-Cristian Rotariu <marian-cristian.rotariu.rb@bp.renesas.com>
> > ---
> >  arch/arm/boot/dts/r8a7742-iwg21d-q7.dts | 84 +++++++++++++++++++++++++
> >  1 file changed, 84 insertions(+)
> >
> > diff --git a/arch/arm/boot/dts/r8a7742-iwg21d-q7.dts b/arch/arm/boot/dts/r8a7742-iwg21d-q7.dts
> > index b3461a61a4bf..cf59fd61e422 100644
> > --- a/arch/arm/boot/dts/r8a7742-iwg21d-q7.dts
> > +++ b/arch/arm/boot/dts/r8a7742-iwg21d-q7.dts
> > @@ -30,6 +30,7 @@
> >
> >  /dts-v1/;
> >  #include "r8a7742-iwg21m.dtsi"
> > +#include <dt-bindings/pwm/pwm.h>
> >
> >  / {
> >       model = "iWave Systems RainboW-G21D-Qseven board based on RZ/G1H";
> > @@ -52,6 +53,50 @@
> >               clock-frequency = <26000000>;
> >       };
> >
> > +     lcd_backlight: backlight {
> > +             compatible = "pwm-backlight";
> > +             pwms = <&tpu 2 5000000 0>;
> > +             brightness-levels = <0 4 8 16 32 64 128 255>;
> > +             pinctrl-0 = <&backlight_pins>;
> > +             pinctrl-names = "default";
> > +             default-brightness-level = <7>;
> > +             enable-gpios = <&gpio3 11 GPIO_ACTIVE_HIGH>;
> > +     };
> > +
> > +     lvds-receiver {
> > +             compatible = "ti,ds90cf384a", "lvds-decoder";
> > +             powerdown-gpios = <&gpio5 28 GPIO_ACTIVE_LOW>;
> > +
> > +             ports {
> > +                     #address-cells = <1>;
> > +                     #size-cells = <0>;
> > +
> > +                     port@0 {
> > +                             reg = <0>;
> > +                             lvds_receiver_in: endpoint {
> > +                                     remote-endpoint = <&lvds0_out>;
> > +                             };
> > +                     };
> > +                     port@1 {
> > +                             reg = <1>;
> > +                             lvds_receiver_out: endpoint {
> > +                                     remote-endpoint = <&panel_in>;
> > +                             };
> > +                     };
> > +             };
> > +     };
> > +
> > +     panel {
> > +             compatible = "edt,etm0700g0dh6";
> > +             backlight = <&lcd_backlight>;
> > +
> > +             port {
> > +                     panel_in: endpoint {
> > +                             remote-endpoint = <&lvds_receiver_out>;
> > +                     };
> > +             };
> > +     };
> > +
> >       reg_1p5v: 1p5v {
> >               compatible = "regulator-fixed";
> >               regulator-name = "1P5V";
> > @@ -129,12 +174,31 @@
> >               VDDIO-supply = <&reg_3p3v>;
> >               VDDD-supply = <&reg_1p5v>;
> >       };
> > +
> > +     touch: touchpanel@38 {
> > +             compatible = "edt,edt-ft5406";
> > +             reg = <0x38>;
> > +             interrupt-parent = <&gpio0>;
> > +             interrupts = <24 IRQ_TYPE_EDGE_FALLING>;
> > +     };
> >  };
> >
> >  &cmt0 {
> >       status = "okay";
> >  };
> >
> > +&du {
> > +     status = "okay";
> > +};
> > +
> > +&gpio0 {
> > +     touch-interrupt {
> > +             gpio-hog;
> > +             gpios = <24 GPIO_ACTIVE_LOW>;
> > +             input;
>
> Is this required, won't requesting the interrupt be enough to configure
> the pin properly ?
>
Agreed.

Cheers,
Prabhakar

> > +     };
> > +};
> > +
> >  &hsusb {
> >       pinctrl-0 = <&usb0_pins>;
> >       pinctrl-names = "default";
> > @@ -165,6 +229,11 @@
> >               function = "avb";
> >       };
> >
> > +     backlight_pins: backlight {
> > +             groups = "tpu0_to2";
> > +             function = "tpu0";
> > +     };
> > +
> >       i2c2_pins: i2c2 {
> >               groups = "i2c2_b";
> >               function = "i2c2";
> > @@ -208,6 +277,17 @@
> >       };
> >  };
> >
> > +&lvds0 {
> > +     status = "okay";
> > +     ports {
> > +             port@1 {
> > +                     lvds0_out: endpoint {
> > +                             remote-endpoint = <&lvds_receiver_in>;
> > +                     };
> > +             };
> > +     };
> > +};
> > +
> >  &rcar_sound {
> >       pinctrl-0 = <&sound_pins>;
> >       pinctrl-names = "default";
> > @@ -261,6 +341,10 @@
> >       shared-pin;
> >  };
> >
> > +&tpu {
> > +     status = "okay";
> > +};
> > +
> >  &usbphy {
> >       status = "okay";
> >  };
>
> --
> Regards,
>
> Laurent Pinchart