* [PATCH v4 0/4] MT7621 PCIe PHY
@ 2020-10-31 12:22 Sergio Paracuellos
2020-10-31 12:22 ` [PATCH v4 1/4] dt-bindings: phy: Add binding for Mediatek " Sergio Paracuellos
` (4 more replies)
0 siblings, 5 replies; 12+ messages in thread
From: Sergio Paracuellos @ 2020-10-31 12:22 UTC (permalink / raw)
To: kishon; +Cc: vkoul, robh+dt, gregkh, devicetree, devel, neil
This series adds support for the PCIe PHY found in the Mediatek
MT7621 SoC.
This is the first attempt to get feedback of what is missing in
this driver to be promoted from staging.
There is also a 'mt7621-pci' driver which is the controller part
which is still in staging and is a client of this phy.
Both drivers have been tested together in a gnubee1 board.
This series are rebased on the top of linux-next:
commit 4e78c578cb98 ("Add linux-next specific files for 20201030")
Changes in v4:
- Bindings moved from txt to yaml so previous Rob's Reviewed-by
is not in the new patch with the yaml file.
- 'phy-cells' property means now if phy is dual-ported.
- Avoid custom 'xlate' function and properly set registers
when the phy is dual ported.
- Add use of 'builtin_platform_driver'.
- Added a patch including myself as maintainer in the
MAINTAINERS file.
- Add a patch removing patch from staging to make easier
the complete inclusion and avoid possible problems might
appear in 'linux-next' if the series are included.
Changes in v3:
- Recollect Rob's Reviewed-by of bindings.
- Make Kishon Vijay suggested changes in v2:
(See https://lkml.org/lkml/2019/4/17/53)
- Kconfig:
* Add depends on COMPILE_TEST
* Select REGMAP_MMIO
- Make use of 'soc_device_attribute' and 'soc_device_match'
- Use regmap mmio API instead of directly 'readl' and 'writel'.
- Use 'platform_get_resource' instead of 'of_address_to_resource'.
Changes in v2:
- Reorder patches to get bindings first in the series.
- Don't use child nodes in the device tree. Use #phy-cells=1 instead.
- Update driver code with new 'xlate' function for the new device tree.
- Minor changes in driver's macros changing some spaces to tabs.
Thanks in advance for your time.
Best regards,
Sergio Paracuellos
Sergio Paracuellos (4):
dt-bindings: phy: Add binding for Mediatek MT7621 PCIe PHY
phy: ralink: Add PHY driver for MT7621 PCIe PHY
MAINTAINERS: add MT7621 PHY PCI maintainer
staging: mt7621-pci-phy: remove driver from staging
.../devicetree/bindings/phy}/mediatek,mt7621-pci-phy.yaml | 0
MAINTAINERS | 6 ++++++
drivers/phy/ralink/Kconfig | 8 ++++++++
drivers/phy/ralink/Makefile | 1 +
.../pci-mt7621-phy.c => phy/ralink/phy-mt7621-pci.c} | 0
drivers/staging/Kconfig | 2 --
drivers/staging/Makefile | 1 -
drivers/staging/mt7621-pci-phy/Kconfig | 8 --------
drivers/staging/mt7621-pci-phy/Makefile | 2 --
drivers/staging/mt7621-pci-phy/TODO | 4 ----
10 files changed, 15 insertions(+), 17 deletions(-)
rename {drivers/staging/mt7621-pci-phy => Documentation/devicetree/bindings/phy}/mediatek,mt7621-pci-phy.yaml (100%)
rename drivers/{staging/mt7621-pci-phy/pci-mt7621-phy.c => phy/ralink/phy-mt7621-pci.c} (100%)
delete mode 100644 drivers/staging/mt7621-pci-phy/Kconfig
delete mode 100644 drivers/staging/mt7621-pci-phy/Makefile
delete mode 100644 drivers/staging/mt7621-pci-phy/TODO
--
2.25.1
^ permalink raw reply [flat|nested] 12+ messages in thread
* [PATCH v4 1/4] dt-bindings: phy: Add binding for Mediatek MT7621 PCIe PHY
2020-10-31 12:22 [PATCH v4 0/4] MT7621 PCIe PHY Sergio Paracuellos
@ 2020-10-31 12:22 ` Sergio Paracuellos
2020-11-04 22:30 ` Rob Herring
2020-10-31 12:22 ` [PATCH v4 2/4] phy: ralink: Add PHY driver for " Sergio Paracuellos
` (3 subsequent siblings)
4 siblings, 1 reply; 12+ messages in thread
From: Sergio Paracuellos @ 2020-10-31 12:22 UTC (permalink / raw)
To: kishon; +Cc: vkoul, robh+dt, gregkh, devicetree, devel, neil
Add bindings to describe Mediatek MT7621 PCIe PHY.
Signed-off-by: Sergio Paracuellos <sergio.paracuellos@gmail.com>
---
.../bindings/phy/mediatek,mt7621-pci-phy.yaml | 36 +++++++++++++++++++
1 file changed, 36 insertions(+)
create mode 100644 Documentation/devicetree/bindings/phy/mediatek,mt7621-pci-phy.yaml
diff --git a/Documentation/devicetree/bindings/phy/mediatek,mt7621-pci-phy.yaml b/Documentation/devicetree/bindings/phy/mediatek,mt7621-pci-phy.yaml
new file mode 100644
index 000000000000..cf32bbc45b5d
--- /dev/null
+++ b/Documentation/devicetree/bindings/phy/mediatek,mt7621-pci-phy.yaml
@@ -0,0 +1,36 @@
+# SPDX-License-Identifier: (GPL-2.0-only or BSD-2-Clause)
+%YAML 1.2
+---
+$id: "http://devicetree.org/schemas/phy/mediatek,mt7621-pci-phy.yaml#"
+$schema: "http://devicetree.org/meta-schemas/core.yaml#"
+
+title: Mediatek Mt7621 PCIe PHY Device Tree Bindings
+
+maintainers:
+ - Sergio Paracuellos <sergio.paracuellos@gmail.com>
+
+properties:
+ compatible:
+ const: mediatek,mt7621-pci-phy
+
+ reg:
+ maxItems: 1
+
+ "#phy-cells":
+ const: 1
+ description: selects if the phy is dual-ported
+
+required:
+ - compatible
+ - reg
+ - "#phy-cells"
+
+additionalProperties: false
+
+examples:
+ - |
+ pcie0_phy: pcie-phy@1e149000 {
+ compatible = "mediatek,mt7621-pci-phy";
+ reg = <0x1e149000 0x0700>;
+ #phy-cells = <1>;
+ };
--
2.25.1
^ permalink raw reply related [flat|nested] 12+ messages in thread
* [PATCH v4 2/4] phy: ralink: Add PHY driver for MT7621 PCIe PHY
2020-10-31 12:22 [PATCH v4 0/4] MT7621 PCIe PHY Sergio Paracuellos
2020-10-31 12:22 ` [PATCH v4 1/4] dt-bindings: phy: Add binding for Mediatek " Sergio Paracuellos
@ 2020-10-31 12:22 ` Sergio Paracuellos
2020-11-19 5:30 ` Vinod Koul
2020-10-31 12:22 ` [PATCH v4 3/4] MAINTAINERS: add MT7621 PHY PCI maintainer Sergio Paracuellos
` (2 subsequent siblings)
4 siblings, 1 reply; 12+ messages in thread
From: Sergio Paracuellos @ 2020-10-31 12:22 UTC (permalink / raw)
To: kishon; +Cc: vkoul, robh+dt, gregkh, devicetree, devel, neil
This patch adds a driver for the PCIe PHY of MT7621 SoC.
Signed-off-by: Sergio Paracuellos <sergio.paracuellos@gmail.com>
---
drivers/phy/ralink/Kconfig | 8 +
drivers/phy/ralink/Makefile | 1 +
drivers/phy/ralink/phy-mt7621-pci.c | 373 ++++++++++++++++++++++++++++
3 files changed, 382 insertions(+)
create mode 100644 drivers/phy/ralink/phy-mt7621-pci.c
diff --git a/drivers/phy/ralink/Kconfig b/drivers/phy/ralink/Kconfig
index da982c9cffb3..2fabb14d2998 100644
--- a/drivers/phy/ralink/Kconfig
+++ b/drivers/phy/ralink/Kconfig
@@ -2,6 +2,14 @@
#
# PHY drivers for Ralink platforms.
#
+config PHY_MT7621_PCI
+ tristate "MediaTek MT7621 PCI PHY Driver"
+ depends on (RALINK || COMPILE_TEST) && OF
+ select GENERIC_PHY
+ select REGMAP_MMIO
+ help
+ Say 'Y' here to add support for MediaTek MT7621 PCI PHY driver,
+
config PHY_RALINK_USB
tristate "Ralink USB PHY driver"
depends on RALINK || COMPILE_TEST
diff --git a/drivers/phy/ralink/Makefile b/drivers/phy/ralink/Makefile
index d8d3ffcf0a15..cda2a4a7ca5e 100644
--- a/drivers/phy/ralink/Makefile
+++ b/drivers/phy/ralink/Makefile
@@ -1,2 +1,3 @@
# SPDX-License-Identifier: GPL-2.0-only
+obj-$(CONFIG_PHY_MT7621_PCI) += phy-mt7621-pci.o
obj-$(CONFIG_PHY_RALINK_USB) += phy-ralink-usb.o
diff --git a/drivers/phy/ralink/phy-mt7621-pci.c b/drivers/phy/ralink/phy-mt7621-pci.c
new file mode 100644
index 000000000000..57743fd22be4
--- /dev/null
+++ b/drivers/phy/ralink/phy-mt7621-pci.c
@@ -0,0 +1,373 @@
+// SPDX-License-Identifier: GPL-2.0+
+/*
+ * Mediatek MT7621 PCI PHY Driver
+ * Author: Sergio Paracuellos <sergio.paracuellos@gmail.com>
+ */
+
+#include <dt-bindings/phy/phy.h>
+#include <linux/bitops.h>
+#include <linux/module.h>
+#include <linux/of_address.h>
+#include <linux/of_device.h>
+#include <linux/phy/phy.h>
+#include <linux/platform_device.h>
+#include <linux/regmap.h>
+#include <linux/sys_soc.h>
+#include <mt7621.h>
+#include <ralink_regs.h>
+
+#define RG_PE1_PIPE_REG 0x02c
+#define RG_PE1_PIPE_RST BIT(12)
+#define RG_PE1_PIPE_CMD_FRC BIT(4)
+
+#define RG_P0_TO_P1_WIDTH 0x100
+#define RG_PE1_H_LCDDS_REG 0x49c
+#define RG_PE1_H_LCDDS_PCW GENMASK(30, 0)
+#define RG_PE1_H_LCDDS_PCW_VAL(x) ((0x7fffffff & (x)) << 0)
+
+#define RG_PE1_FRC_H_XTAL_REG 0x400
+#define RG_PE1_FRC_H_XTAL_TYPE BIT(8)
+#define RG_PE1_H_XTAL_TYPE GENMASK(10, 9)
+#define RG_PE1_H_XTAL_TYPE_VAL(x) ((0x3 & (x)) << 9)
+
+#define RG_PE1_FRC_PHY_REG 0x000
+#define RG_PE1_FRC_PHY_EN BIT(4)
+#define RG_PE1_PHY_EN BIT(5)
+
+#define RG_PE1_H_PLL_REG 0x490
+#define RG_PE1_H_PLL_BC GENMASK(23, 22)
+#define RG_PE1_H_PLL_BC_VAL(x) ((0x3 & (x)) << 22)
+#define RG_PE1_H_PLL_BP GENMASK(21, 18)
+#define RG_PE1_H_PLL_BP_VAL(x) ((0xf & (x)) << 18)
+#define RG_PE1_H_PLL_IR GENMASK(15, 12)
+#define RG_PE1_H_PLL_IR_VAL(x) ((0xf & (x)) << 12)
+#define RG_PE1_H_PLL_IC GENMASK(11, 8)
+#define RG_PE1_H_PLL_IC_VAL(x) ((0xf & (x)) << 8)
+#define RG_PE1_H_PLL_PREDIV GENMASK(7, 6)
+#define RG_PE1_H_PLL_PREDIV_VAL(x) ((0x3 & (x)) << 6)
+#define RG_PE1_PLL_DIVEN GENMASK(3, 1)
+#define RG_PE1_PLL_DIVEN_VAL(x) ((0x7 & (x)) << 1)
+
+#define RG_PE1_H_PLL_FBKSEL_REG 0x4bc
+#define RG_PE1_H_PLL_FBKSEL GENMASK(5, 4)
+#define RG_PE1_H_PLL_FBKSEL_VAL(x) ((0x3 & (x)) << 4)
+
+#define RG_PE1_H_LCDDS_SSC_PRD_REG 0x4a4
+#define RG_PE1_H_LCDDS_SSC_PRD GENMASK(15, 0)
+#define RG_PE1_H_LCDDS_SSC_PRD_VAL(x) ((0xffff & (x)) << 0)
+
+#define RG_PE1_H_LCDDS_SSC_DELTA_REG 0x4a8
+#define RG_PE1_H_LCDDS_SSC_DELTA GENMASK(11, 0)
+#define RG_PE1_H_LCDDS_SSC_DELTA_VAL(x) ((0xfff & (x)) << 0)
+#define RG_PE1_H_LCDDS_SSC_DELTA1 GENMASK(27, 16)
+#define RG_PE1_H_LCDDS_SSC_DELTA1_VAL(x) ((0xff & (x)) << 16)
+
+#define RG_PE1_LCDDS_CLK_PH_INV_REG 0x4a0
+#define RG_PE1_LCDDS_CLK_PH_INV BIT(5)
+
+#define RG_PE1_H_PLL_BR_REG 0x4ac
+#define RG_PE1_H_PLL_BR GENMASK(18, 16)
+#define RG_PE1_H_PLL_BR_VAL(x) ((0x7 & (x)) << 16)
+
+#define RG_PE1_MSTCKDIV_REG 0x414
+#define RG_PE1_MSTCKDIV GENMASK(7, 6)
+#define RG_PE1_MSTCKDIV_VAL(x) ((0x3 & (x)) << 6)
+
+#define RG_PE1_FRC_MSTCKDIV BIT(5)
+
+#define XTAL_MODE_SEL_SHIFT 6
+#define XTAL_MODE_SEL_MASK 0x7
+
+#define MAX_PHYS 2
+
+/**
+ * struct mt7621_pci_phy - Mt7621 Pcie PHY core
+ * @dev: pointer to device
+ * @regmap: kernel regmap pointer
+ * @phy: pointer to the kernel PHY device
+ * @port_base: base register
+ * @has_dual_port: if the phy has dual ports.
+ * @bypass_pipe_rst: mark if 'mt7621_bypass_pipe_rst'
+ * needs to be executed. Depends on chip revision.
+ */
+struct mt7621_pci_phy {
+ struct device *dev;
+ struct regmap *regmap;
+ struct phy *phy;
+ void __iomem *port_base;
+ bool has_dual_port;
+ bool bypass_pipe_rst;
+};
+
+static inline u32 phy_read(struct mt7621_pci_phy *phy, u32 reg)
+{
+ u32 val;
+
+ regmap_read(phy->regmap, reg, &val);
+
+ return val;
+}
+
+static inline void phy_write(struct mt7621_pci_phy *phy, u32 val, u32 reg)
+{
+ regmap_write(phy->regmap, reg, val);
+}
+
+static inline void mt7621_phy_rmw(struct mt7621_pci_phy *phy,
+ u32 reg, u32 clr, u32 set)
+{
+ u32 val = phy_read(phy, reg);
+
+ val &= ~clr;
+ val |= set;
+ phy_write(phy, val, reg);
+}
+
+static void mt7621_bypass_pipe_rst(struct mt7621_pci_phy *phy)
+{
+ mt7621_phy_rmw(phy, RG_PE1_PIPE_REG, 0, RG_PE1_PIPE_RST);
+ mt7621_phy_rmw(phy, RG_PE1_PIPE_REG, 0, RG_PE1_PIPE_CMD_FRC);
+
+ if (phy->has_dual_port) {
+ mt7621_phy_rmw(phy, RG_PE1_PIPE_REG + RG_P0_TO_P1_WIDTH,
+ 0, RG_PE1_PIPE_RST);
+ mt7621_phy_rmw(phy, RG_PE1_PIPE_REG + RG_P0_TO_P1_WIDTH,
+ 0, RG_PE1_PIPE_CMD_FRC);
+ }
+}
+
+static void mt7621_set_phy_for_ssc(struct mt7621_pci_phy *phy)
+{
+ struct device *dev = phy->dev;
+ u32 xtal_mode;
+
+ xtal_mode = (rt_sysc_r32(SYSC_REG_SYSTEM_CONFIG0)
+ >> XTAL_MODE_SEL_SHIFT) & XTAL_MODE_SEL_MASK;
+
+ /* Set PCIe Port PHY to disable SSC */
+ /* Debug Xtal Type */
+ mt7621_phy_rmw(phy, RG_PE1_FRC_H_XTAL_REG,
+ RG_PE1_FRC_H_XTAL_TYPE | RG_PE1_H_XTAL_TYPE,
+ RG_PE1_FRC_H_XTAL_TYPE | RG_PE1_H_XTAL_TYPE_VAL(0x00));
+
+ /* disable port */
+ mt7621_phy_rmw(phy, RG_PE1_FRC_PHY_REG,
+ RG_PE1_PHY_EN, RG_PE1_FRC_PHY_EN);
+
+ if (phy->has_dual_port) {
+ mt7621_phy_rmw(phy, RG_PE1_FRC_PHY_REG + RG_P0_TO_P1_WIDTH,
+ RG_PE1_PHY_EN, RG_PE1_FRC_PHY_EN);
+ }
+
+ if (xtal_mode <= 5 && xtal_mode >= 3) { /* 40MHz Xtal */
+ /* Set Pre-divider ratio (for host mode) */
+ mt7621_phy_rmw(phy, RG_PE1_H_PLL_REG,
+ RG_PE1_H_PLL_PREDIV,
+ RG_PE1_H_PLL_PREDIV_VAL(0x01));
+ dev_info(dev, "Xtal is 40MHz\n");
+ } else if (xtal_mode >= 6) { /* 25MHz Xal */
+ mt7621_phy_rmw(phy, RG_PE1_H_PLL_REG,
+ RG_PE1_H_PLL_PREDIV,
+ RG_PE1_H_PLL_PREDIV_VAL(0x00));
+ /* Select feedback clock */
+ mt7621_phy_rmw(phy, RG_PE1_H_PLL_FBKSEL_REG,
+ RG_PE1_H_PLL_FBKSEL,
+ RG_PE1_H_PLL_FBKSEL_VAL(0x01));
+ /* DDS NCPO PCW (for host mode) */
+ mt7621_phy_rmw(phy, RG_PE1_H_LCDDS_SSC_PRD_REG,
+ RG_PE1_H_LCDDS_SSC_PRD,
+ RG_PE1_H_LCDDS_SSC_PRD_VAL(0x18000000));
+ /* DDS SSC dither period control */
+ mt7621_phy_rmw(phy, RG_PE1_H_LCDDS_SSC_PRD_REG,
+ RG_PE1_H_LCDDS_SSC_PRD,
+ RG_PE1_H_LCDDS_SSC_PRD_VAL(0x18d));
+ /* DDS SSC dither amplitude control */
+ mt7621_phy_rmw(phy, RG_PE1_H_LCDDS_SSC_DELTA_REG,
+ RG_PE1_H_LCDDS_SSC_DELTA |
+ RG_PE1_H_LCDDS_SSC_DELTA1,
+ RG_PE1_H_LCDDS_SSC_DELTA_VAL(0x4a) |
+ RG_PE1_H_LCDDS_SSC_DELTA1_VAL(0x4a));
+ dev_info(dev, "Xtal is 25MHz\n");
+ } else { /* 20MHz Xtal */
+ mt7621_phy_rmw(phy, RG_PE1_H_PLL_REG,
+ RG_PE1_H_PLL_PREDIV,
+ RG_PE1_H_PLL_PREDIV_VAL(0x00));
+
+ dev_info(dev, "Xtal is 20MHz\n");
+ }
+
+ /* DDS clock inversion */
+ mt7621_phy_rmw(phy, RG_PE1_LCDDS_CLK_PH_INV_REG,
+ RG_PE1_LCDDS_CLK_PH_INV, RG_PE1_LCDDS_CLK_PH_INV);
+
+ /* Set PLL bits */
+ mt7621_phy_rmw(phy, RG_PE1_H_PLL_REG,
+ RG_PE1_H_PLL_BC | RG_PE1_H_PLL_BP | RG_PE1_H_PLL_IR |
+ RG_PE1_H_PLL_IC | RG_PE1_PLL_DIVEN,
+ RG_PE1_H_PLL_BC_VAL(0x02) | RG_PE1_H_PLL_BP_VAL(0x06) |
+ RG_PE1_H_PLL_IR_VAL(0x02) | RG_PE1_H_PLL_IC_VAL(0x01) |
+ RG_PE1_PLL_DIVEN_VAL(0x02));
+
+ mt7621_phy_rmw(phy, RG_PE1_H_PLL_BR_REG,
+ RG_PE1_H_PLL_BR, RG_PE1_H_PLL_BR_VAL(0x00));
+
+ if (xtal_mode <= 5 && xtal_mode >= 3) { /* 40MHz Xtal */
+ /* set force mode enable of da_pe1_mstckdiv */
+ mt7621_phy_rmw(phy, RG_PE1_MSTCKDIV_REG,
+ RG_PE1_MSTCKDIV | RG_PE1_FRC_MSTCKDIV,
+ RG_PE1_MSTCKDIV_VAL(0x01) | RG_PE1_FRC_MSTCKDIV);
+ }
+}
+
+static int mt7621_pci_phy_init(struct phy *phy)
+{
+ struct mt7621_pci_phy *mphy = phy_get_drvdata(phy);
+
+ if (mphy->bypass_pipe_rst)
+ mt7621_bypass_pipe_rst(mphy);
+
+ mt7621_set_phy_for_ssc(mphy);
+
+ return 0;
+}
+
+static int mt7621_pci_phy_power_on(struct phy *phy)
+{
+ struct mt7621_pci_phy *mphy = phy_get_drvdata(phy);
+
+ /* Enable PHY and disable force mode */
+ mt7621_phy_rmw(mphy, RG_PE1_FRC_PHY_REG,
+ RG_PE1_FRC_PHY_EN, RG_PE1_PHY_EN);
+
+ if (mphy->has_dual_port) {
+ mt7621_phy_rmw(mphy, RG_PE1_FRC_PHY_REG + RG_P0_TO_P1_WIDTH,
+ RG_PE1_FRC_PHY_EN, RG_PE1_PHY_EN);
+ }
+
+ return 0;
+}
+
+static int mt7621_pci_phy_power_off(struct phy *phy)
+{
+ struct mt7621_pci_phy *mphy = phy_get_drvdata(phy);
+
+ /* Disable PHY */
+ mt7621_phy_rmw(mphy, RG_PE1_FRC_PHY_REG,
+ RG_PE1_PHY_EN, RG_PE1_FRC_PHY_EN);
+
+ if (mphy->has_dual_port) {
+ mt7621_phy_rmw(mphy, RG_PE1_FRC_PHY_REG + RG_P0_TO_P1_WIDTH,
+ RG_PE1_PHY_EN, RG_PE1_FRC_PHY_EN);
+ }
+
+ return 0;
+}
+
+static int mt7621_pci_phy_exit(struct phy *phy)
+{
+ return 0;
+}
+
+static const struct phy_ops mt7621_pci_phy_ops = {
+ .init = mt7621_pci_phy_init,
+ .exit = mt7621_pci_phy_exit,
+ .power_on = mt7621_pci_phy_power_on,
+ .power_off = mt7621_pci_phy_power_off,
+ .owner = THIS_MODULE,
+};
+
+static struct phy *mt7621_pcie_phy_of_xlate(struct device *dev,
+ struct of_phandle_args *args)
+{
+ struct mt7621_pci_phy *mt7621_phy = dev_get_drvdata(dev);
+
+ if (WARN_ON(args->args[0] >= MAX_PHYS))
+ return ERR_PTR(-ENODEV);
+
+ mt7621_phy->has_dual_port = args->args[0];
+
+ dev_info(dev, "PHY for 0x%08x (dual port = %d)\n",
+ (unsigned int)mt7621_phy->port_base, mt7621_phy->has_dual_port);
+
+ return mt7621_phy->phy;
+}
+
+static const struct soc_device_attribute mt7621_pci_quirks_match[] = {
+ { .soc_id = "mt7621", .revision = "E2" }
+};
+
+static const struct regmap_config mt7621_pci_phy_regmap_config = {
+ .reg_bits = 32,
+ .val_bits = 32,
+ .reg_stride = 4,
+ .max_register = 0x700,
+};
+
+static int mt7621_pci_phy_probe(struct platform_device *pdev)
+{
+ struct device *dev = &pdev->dev;
+ const struct soc_device_attribute *attr;
+ struct phy_provider *provider;
+ struct mt7621_pci_phy *phy;
+ struct resource *res;
+
+ phy = devm_kzalloc(dev, sizeof(*phy), GFP_KERNEL);
+ if (!phy)
+ return -ENOMEM;
+
+ attr = soc_device_match(mt7621_pci_quirks_match);
+ if (attr)
+ phy->bypass_pipe_rst = true;
+
+ phy->dev = dev;
+ platform_set_drvdata(pdev, phy);
+
+ res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+ if (!res) {
+ dev_err(dev, "failed to get address resource\n");
+ return -ENXIO;
+ }
+
+ phy->port_base = devm_ioremap_resource(dev, res);
+ if (IS_ERR(phy->port_base)) {
+ dev_err(dev, "failed to remap phy regs\n");
+ return PTR_ERR(phy->port_base);
+ }
+
+ phy->regmap = devm_regmap_init_mmio(phy->dev, phy->port_base,
+ &mt7621_pci_phy_regmap_config);
+ if (IS_ERR(phy->regmap))
+ return PTR_ERR(phy->regmap);
+
+ phy->phy = devm_phy_create(dev, dev->of_node, &mt7621_pci_phy_ops);
+ if (IS_ERR(phy)) {
+ dev_err(dev, "failed to create phy\n");
+ return PTR_ERR(phy);
+ }
+
+ phy_set_drvdata(phy->phy, phy);
+
+ provider = devm_of_phy_provider_register(dev, mt7621_pcie_phy_of_xlate);
+
+ return PTR_ERR_OR_ZERO(provider);
+}
+
+static const struct of_device_id mt7621_pci_phy_ids[] = {
+ { .compatible = "mediatek,mt7621-pci-phy" },
+ {},
+};
+MODULE_DEVICE_TABLE(of, mt7621_pci_ids);
+
+static struct platform_driver mt7621_pci_phy_driver = {
+ .probe = mt7621_pci_phy_probe,
+ .driver = {
+ .name = "mt7621-pci-phy",
+ .of_match_table = of_match_ptr(mt7621_pci_phy_ids),
+ },
+};
+
+builtin_platform_driver(mt7621_pci_phy_driver);
+
+MODULE_AUTHOR("Sergio Paracuellos <sergio.paracuellos@gmail.com>");
+MODULE_DESCRIPTION("MediaTek MT7621 PCIe PHY driver");
+MODULE_LICENSE("GPL v2");
--
2.25.1
^ permalink raw reply related [flat|nested] 12+ messages in thread
* [PATCH v4 3/4] MAINTAINERS: add MT7621 PHY PCI maintainer
2020-10-31 12:22 [PATCH v4 0/4] MT7621 PCIe PHY Sergio Paracuellos
2020-10-31 12:22 ` [PATCH v4 1/4] dt-bindings: phy: Add binding for Mediatek " Sergio Paracuellos
2020-10-31 12:22 ` [PATCH v4 2/4] phy: ralink: Add PHY driver for " Sergio Paracuellos
@ 2020-10-31 12:22 ` Sergio Paracuellos
2020-10-31 12:22 ` [PATCH v4 4/4] staging: mt7621-pci-phy: remove driver from staging Sergio Paracuellos
2020-11-10 12:14 ` [PATCH v4 0/4] MT7621 PCIe PHY Sergio Paracuellos
4 siblings, 0 replies; 12+ messages in thread
From: Sergio Paracuellos @ 2020-10-31 12:22 UTC (permalink / raw)
To: kishon; +Cc: vkoul, robh+dt, gregkh, devicetree, devel, neil
Adding myself as maintainer for mt7621 pci phy driver.
Signed-off-by: Sergio Paracuellos <sergio.paracuellos@gmail.com>
---
MAINTAINERS | 6 ++++++
1 file changed, 6 insertions(+)
diff --git a/MAINTAINERS b/MAINTAINERS
index aefbbecfb266..31f808e58e73 100644
--- a/MAINTAINERS
+++ b/MAINTAINERS
@@ -11100,6 +11100,12 @@ S: Maintained
F: Documentation/devicetree/bindings/i2c/i2c-mt7621.txt
F: drivers/i2c/busses/i2c-mt7621.c
+MEDIATEK MT7621 PHY PCI DRIVER
+M: Sergio Paracuellos <sergio.paracuellos@gmail.com>
+S: Maintained
+F: Documentation/devicetree/bindings/phy/mediatek,mt7621-pci-phy.yaml
+F: drivers/phy/ralink/phy-mt7621-pci.c
+
MEDIATEK NAND CONTROLLER DRIVER
L: linux-mtd@lists.infradead.org
S: Orphan
--
2.25.1
^ permalink raw reply related [flat|nested] 12+ messages in thread
* [PATCH v4 4/4] staging: mt7621-pci-phy: remove driver from staging
2020-10-31 12:22 [PATCH v4 0/4] MT7621 PCIe PHY Sergio Paracuellos
` (2 preceding siblings ...)
2020-10-31 12:22 ` [PATCH v4 3/4] MAINTAINERS: add MT7621 PHY PCI maintainer Sergio Paracuellos
@ 2020-10-31 12:22 ` Sergio Paracuellos
2020-11-06 9:43 ` Greg KH
2020-11-10 12:14 ` [PATCH v4 0/4] MT7621 PCIe PHY Sergio Paracuellos
4 siblings, 1 reply; 12+ messages in thread
From: Sergio Paracuellos @ 2020-10-31 12:22 UTC (permalink / raw)
To: kishon; +Cc: vkoul, robh+dt, gregkh, devicetree, devel, neil
Remove this driver from staging because it has been moved
into its properly place in the kernel.
Signed-off-by: Sergio Paracuellos <sergio.paracuellos@gmail.com>
---
drivers/staging/Kconfig | 2 -
drivers/staging/Makefile | 1 -
drivers/staging/mt7621-pci-phy/Kconfig | 8 -
drivers/staging/mt7621-pci-phy/Makefile | 2 -
drivers/staging/mt7621-pci-phy/TODO | 4 -
.../mediatek,mt7621-pci-phy.yaml | 36 --
.../staging/mt7621-pci-phy/pci-mt7621-phy.c | 373 ------------------
7 files changed, 426 deletions(-)
delete mode 100644 drivers/staging/mt7621-pci-phy/Kconfig
delete mode 100644 drivers/staging/mt7621-pci-phy/Makefile
delete mode 100644 drivers/staging/mt7621-pci-phy/TODO
delete mode 100644 drivers/staging/mt7621-pci-phy/mediatek,mt7621-pci-phy.yaml
delete mode 100644 drivers/staging/mt7621-pci-phy/pci-mt7621-phy.c
diff --git a/drivers/staging/Kconfig b/drivers/staging/Kconfig
index 2d0310448eba..8a03ba56def5 100644
--- a/drivers/staging/Kconfig
+++ b/drivers/staging/Kconfig
@@ -94,8 +94,6 @@ source "drivers/staging/pi433/Kconfig"
source "drivers/staging/mt7621-pci/Kconfig"
-source "drivers/staging/mt7621-pci-phy/Kconfig"
-
source "drivers/staging/mt7621-pinctrl/Kconfig"
source "drivers/staging/mt7621-dma/Kconfig"
diff --git a/drivers/staging/Makefile b/drivers/staging/Makefile
index 757a892ab5b9..39319161301c 100644
--- a/drivers/staging/Makefile
+++ b/drivers/staging/Makefile
@@ -37,7 +37,6 @@ obj-$(CONFIG_GREYBUS) += greybus/
obj-$(CONFIG_BCM2835_VCHIQ) += vc04_services/
obj-$(CONFIG_PI433) += pi433/
obj-$(CONFIG_PCI_MT7621) += mt7621-pci/
-obj-$(CONFIG_PCI_MT7621_PHY) += mt7621-pci-phy/
obj-$(CONFIG_PINCTRL_RT2880) += mt7621-pinctrl/
obj-$(CONFIG_SOC_MT7621) += mt7621-dma/
obj-$(CONFIG_DMA_RALINK) += ralink-gdma/
diff --git a/drivers/staging/mt7621-pci-phy/Kconfig b/drivers/staging/mt7621-pci-phy/Kconfig
deleted file mode 100644
index 263e0a91c424..000000000000
--- a/drivers/staging/mt7621-pci-phy/Kconfig
+++ /dev/null
@@ -1,8 +0,0 @@
-# SPDX-License-Identifier: GPL-2.0
-config PCI_MT7621_PHY
- tristate "MediaTek MT7621 PCI PHY Driver"
- depends on RALINK && OF
- select GENERIC_PHY
- help
- Say 'Y' here to add support for MediaTek MT7621 PCI PHY driver,
-
diff --git a/drivers/staging/mt7621-pci-phy/Makefile b/drivers/staging/mt7621-pci-phy/Makefile
deleted file mode 100644
index b4d99b9119e0..000000000000
--- a/drivers/staging/mt7621-pci-phy/Makefile
+++ /dev/null
@@ -1,2 +0,0 @@
-# SPDX-License-Identifier: GPL-2.0
-obj-$(CONFIG_PCI_MT7621_PHY) += pci-mt7621-phy.o
diff --git a/drivers/staging/mt7621-pci-phy/TODO b/drivers/staging/mt7621-pci-phy/TODO
deleted file mode 100644
index a255e8f753eb..000000000000
--- a/drivers/staging/mt7621-pci-phy/TODO
+++ /dev/null
@@ -1,4 +0,0 @@
-
-- general code review and cleanup
-
-Cc: NeilBrown <neil@brown.name> and Sergio Paracuellos <sergio.paracuellos@gmail.com>
diff --git a/drivers/staging/mt7621-pci-phy/mediatek,mt7621-pci-phy.yaml b/drivers/staging/mt7621-pci-phy/mediatek,mt7621-pci-phy.yaml
deleted file mode 100644
index cf32bbc45b5d..000000000000
--- a/drivers/staging/mt7621-pci-phy/mediatek,mt7621-pci-phy.yaml
+++ /dev/null
@@ -1,36 +0,0 @@
-# SPDX-License-Identifier: GPL-2.0
-%YAML 1.2
----
-$id: "http://devicetree.org/schemas/phy/mediatek,mt7621-pci-phy.yaml#"
-$schema: "http://devicetree.org/meta-schemas/core.yaml#"
-
-title: Mediatek Mt7621 PCIe PHY Device Tree Bindings
-
-maintainers:
- - Sergio Paracuellos <sergio.paracuellos@gmail.com>
-
-properties:
- compatible:
- const: mediatek,mt7621-pci-phy
-
- reg:
- maxItems: 1
-
- "#phy-cells":
- const: 1
- description: selects if the phy is dual-ported
-
-required:
- - compatible
- - reg
- - "#phy-cells"
-
-additionalProperties: false
-
-examples:
- - |
- pcie0_phy: pcie-phy@1e149000 {
- compatible = "mediatek,mt7621-pci-phy";
- reg = <0x1e149000 0x0700>;
- #phy-cells = <1>;
- };
diff --git a/drivers/staging/mt7621-pci-phy/pci-mt7621-phy.c b/drivers/staging/mt7621-pci-phy/pci-mt7621-phy.c
deleted file mode 100644
index 57743fd22be4..000000000000
--- a/drivers/staging/mt7621-pci-phy/pci-mt7621-phy.c
+++ /dev/null
@@ -1,373 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0+
-/*
- * Mediatek MT7621 PCI PHY Driver
- * Author: Sergio Paracuellos <sergio.paracuellos@gmail.com>
- */
-
-#include <dt-bindings/phy/phy.h>
-#include <linux/bitops.h>
-#include <linux/module.h>
-#include <linux/of_address.h>
-#include <linux/of_device.h>
-#include <linux/phy/phy.h>
-#include <linux/platform_device.h>
-#include <linux/regmap.h>
-#include <linux/sys_soc.h>
-#include <mt7621.h>
-#include <ralink_regs.h>
-
-#define RG_PE1_PIPE_REG 0x02c
-#define RG_PE1_PIPE_RST BIT(12)
-#define RG_PE1_PIPE_CMD_FRC BIT(4)
-
-#define RG_P0_TO_P1_WIDTH 0x100
-#define RG_PE1_H_LCDDS_REG 0x49c
-#define RG_PE1_H_LCDDS_PCW GENMASK(30, 0)
-#define RG_PE1_H_LCDDS_PCW_VAL(x) ((0x7fffffff & (x)) << 0)
-
-#define RG_PE1_FRC_H_XTAL_REG 0x400
-#define RG_PE1_FRC_H_XTAL_TYPE BIT(8)
-#define RG_PE1_H_XTAL_TYPE GENMASK(10, 9)
-#define RG_PE1_H_XTAL_TYPE_VAL(x) ((0x3 & (x)) << 9)
-
-#define RG_PE1_FRC_PHY_REG 0x000
-#define RG_PE1_FRC_PHY_EN BIT(4)
-#define RG_PE1_PHY_EN BIT(5)
-
-#define RG_PE1_H_PLL_REG 0x490
-#define RG_PE1_H_PLL_BC GENMASK(23, 22)
-#define RG_PE1_H_PLL_BC_VAL(x) ((0x3 & (x)) << 22)
-#define RG_PE1_H_PLL_BP GENMASK(21, 18)
-#define RG_PE1_H_PLL_BP_VAL(x) ((0xf & (x)) << 18)
-#define RG_PE1_H_PLL_IR GENMASK(15, 12)
-#define RG_PE1_H_PLL_IR_VAL(x) ((0xf & (x)) << 12)
-#define RG_PE1_H_PLL_IC GENMASK(11, 8)
-#define RG_PE1_H_PLL_IC_VAL(x) ((0xf & (x)) << 8)
-#define RG_PE1_H_PLL_PREDIV GENMASK(7, 6)
-#define RG_PE1_H_PLL_PREDIV_VAL(x) ((0x3 & (x)) << 6)
-#define RG_PE1_PLL_DIVEN GENMASK(3, 1)
-#define RG_PE1_PLL_DIVEN_VAL(x) ((0x7 & (x)) << 1)
-
-#define RG_PE1_H_PLL_FBKSEL_REG 0x4bc
-#define RG_PE1_H_PLL_FBKSEL GENMASK(5, 4)
-#define RG_PE1_H_PLL_FBKSEL_VAL(x) ((0x3 & (x)) << 4)
-
-#define RG_PE1_H_LCDDS_SSC_PRD_REG 0x4a4
-#define RG_PE1_H_LCDDS_SSC_PRD GENMASK(15, 0)
-#define RG_PE1_H_LCDDS_SSC_PRD_VAL(x) ((0xffff & (x)) << 0)
-
-#define RG_PE1_H_LCDDS_SSC_DELTA_REG 0x4a8
-#define RG_PE1_H_LCDDS_SSC_DELTA GENMASK(11, 0)
-#define RG_PE1_H_LCDDS_SSC_DELTA_VAL(x) ((0xfff & (x)) << 0)
-#define RG_PE1_H_LCDDS_SSC_DELTA1 GENMASK(27, 16)
-#define RG_PE1_H_LCDDS_SSC_DELTA1_VAL(x) ((0xff & (x)) << 16)
-
-#define RG_PE1_LCDDS_CLK_PH_INV_REG 0x4a0
-#define RG_PE1_LCDDS_CLK_PH_INV BIT(5)
-
-#define RG_PE1_H_PLL_BR_REG 0x4ac
-#define RG_PE1_H_PLL_BR GENMASK(18, 16)
-#define RG_PE1_H_PLL_BR_VAL(x) ((0x7 & (x)) << 16)
-
-#define RG_PE1_MSTCKDIV_REG 0x414
-#define RG_PE1_MSTCKDIV GENMASK(7, 6)
-#define RG_PE1_MSTCKDIV_VAL(x) ((0x3 & (x)) << 6)
-
-#define RG_PE1_FRC_MSTCKDIV BIT(5)
-
-#define XTAL_MODE_SEL_SHIFT 6
-#define XTAL_MODE_SEL_MASK 0x7
-
-#define MAX_PHYS 2
-
-/**
- * struct mt7621_pci_phy - Mt7621 Pcie PHY core
- * @dev: pointer to device
- * @regmap: kernel regmap pointer
- * @phy: pointer to the kernel PHY device
- * @port_base: base register
- * @has_dual_port: if the phy has dual ports.
- * @bypass_pipe_rst: mark if 'mt7621_bypass_pipe_rst'
- * needs to be executed. Depends on chip revision.
- */
-struct mt7621_pci_phy {
- struct device *dev;
- struct regmap *regmap;
- struct phy *phy;
- void __iomem *port_base;
- bool has_dual_port;
- bool bypass_pipe_rst;
-};
-
-static inline u32 phy_read(struct mt7621_pci_phy *phy, u32 reg)
-{
- u32 val;
-
- regmap_read(phy->regmap, reg, &val);
-
- return val;
-}
-
-static inline void phy_write(struct mt7621_pci_phy *phy, u32 val, u32 reg)
-{
- regmap_write(phy->regmap, reg, val);
-}
-
-static inline void mt7621_phy_rmw(struct mt7621_pci_phy *phy,
- u32 reg, u32 clr, u32 set)
-{
- u32 val = phy_read(phy, reg);
-
- val &= ~clr;
- val |= set;
- phy_write(phy, val, reg);
-}
-
-static void mt7621_bypass_pipe_rst(struct mt7621_pci_phy *phy)
-{
- mt7621_phy_rmw(phy, RG_PE1_PIPE_REG, 0, RG_PE1_PIPE_RST);
- mt7621_phy_rmw(phy, RG_PE1_PIPE_REG, 0, RG_PE1_PIPE_CMD_FRC);
-
- if (phy->has_dual_port) {
- mt7621_phy_rmw(phy, RG_PE1_PIPE_REG + RG_P0_TO_P1_WIDTH,
- 0, RG_PE1_PIPE_RST);
- mt7621_phy_rmw(phy, RG_PE1_PIPE_REG + RG_P0_TO_P1_WIDTH,
- 0, RG_PE1_PIPE_CMD_FRC);
- }
-}
-
-static void mt7621_set_phy_for_ssc(struct mt7621_pci_phy *phy)
-{
- struct device *dev = phy->dev;
- u32 xtal_mode;
-
- xtal_mode = (rt_sysc_r32(SYSC_REG_SYSTEM_CONFIG0)
- >> XTAL_MODE_SEL_SHIFT) & XTAL_MODE_SEL_MASK;
-
- /* Set PCIe Port PHY to disable SSC */
- /* Debug Xtal Type */
- mt7621_phy_rmw(phy, RG_PE1_FRC_H_XTAL_REG,
- RG_PE1_FRC_H_XTAL_TYPE | RG_PE1_H_XTAL_TYPE,
- RG_PE1_FRC_H_XTAL_TYPE | RG_PE1_H_XTAL_TYPE_VAL(0x00));
-
- /* disable port */
- mt7621_phy_rmw(phy, RG_PE1_FRC_PHY_REG,
- RG_PE1_PHY_EN, RG_PE1_FRC_PHY_EN);
-
- if (phy->has_dual_port) {
- mt7621_phy_rmw(phy, RG_PE1_FRC_PHY_REG + RG_P0_TO_P1_WIDTH,
- RG_PE1_PHY_EN, RG_PE1_FRC_PHY_EN);
- }
-
- if (xtal_mode <= 5 && xtal_mode >= 3) { /* 40MHz Xtal */
- /* Set Pre-divider ratio (for host mode) */
- mt7621_phy_rmw(phy, RG_PE1_H_PLL_REG,
- RG_PE1_H_PLL_PREDIV,
- RG_PE1_H_PLL_PREDIV_VAL(0x01));
- dev_info(dev, "Xtal is 40MHz\n");
- } else if (xtal_mode >= 6) { /* 25MHz Xal */
- mt7621_phy_rmw(phy, RG_PE1_H_PLL_REG,
- RG_PE1_H_PLL_PREDIV,
- RG_PE1_H_PLL_PREDIV_VAL(0x00));
- /* Select feedback clock */
- mt7621_phy_rmw(phy, RG_PE1_H_PLL_FBKSEL_REG,
- RG_PE1_H_PLL_FBKSEL,
- RG_PE1_H_PLL_FBKSEL_VAL(0x01));
- /* DDS NCPO PCW (for host mode) */
- mt7621_phy_rmw(phy, RG_PE1_H_LCDDS_SSC_PRD_REG,
- RG_PE1_H_LCDDS_SSC_PRD,
- RG_PE1_H_LCDDS_SSC_PRD_VAL(0x18000000));
- /* DDS SSC dither period control */
- mt7621_phy_rmw(phy, RG_PE1_H_LCDDS_SSC_PRD_REG,
- RG_PE1_H_LCDDS_SSC_PRD,
- RG_PE1_H_LCDDS_SSC_PRD_VAL(0x18d));
- /* DDS SSC dither amplitude control */
- mt7621_phy_rmw(phy, RG_PE1_H_LCDDS_SSC_DELTA_REG,
- RG_PE1_H_LCDDS_SSC_DELTA |
- RG_PE1_H_LCDDS_SSC_DELTA1,
- RG_PE1_H_LCDDS_SSC_DELTA_VAL(0x4a) |
- RG_PE1_H_LCDDS_SSC_DELTA1_VAL(0x4a));
- dev_info(dev, "Xtal is 25MHz\n");
- } else { /* 20MHz Xtal */
- mt7621_phy_rmw(phy, RG_PE1_H_PLL_REG,
- RG_PE1_H_PLL_PREDIV,
- RG_PE1_H_PLL_PREDIV_VAL(0x00));
-
- dev_info(dev, "Xtal is 20MHz\n");
- }
-
- /* DDS clock inversion */
- mt7621_phy_rmw(phy, RG_PE1_LCDDS_CLK_PH_INV_REG,
- RG_PE1_LCDDS_CLK_PH_INV, RG_PE1_LCDDS_CLK_PH_INV);
-
- /* Set PLL bits */
- mt7621_phy_rmw(phy, RG_PE1_H_PLL_REG,
- RG_PE1_H_PLL_BC | RG_PE1_H_PLL_BP | RG_PE1_H_PLL_IR |
- RG_PE1_H_PLL_IC | RG_PE1_PLL_DIVEN,
- RG_PE1_H_PLL_BC_VAL(0x02) | RG_PE1_H_PLL_BP_VAL(0x06) |
- RG_PE1_H_PLL_IR_VAL(0x02) | RG_PE1_H_PLL_IC_VAL(0x01) |
- RG_PE1_PLL_DIVEN_VAL(0x02));
-
- mt7621_phy_rmw(phy, RG_PE1_H_PLL_BR_REG,
- RG_PE1_H_PLL_BR, RG_PE1_H_PLL_BR_VAL(0x00));
-
- if (xtal_mode <= 5 && xtal_mode >= 3) { /* 40MHz Xtal */
- /* set force mode enable of da_pe1_mstckdiv */
- mt7621_phy_rmw(phy, RG_PE1_MSTCKDIV_REG,
- RG_PE1_MSTCKDIV | RG_PE1_FRC_MSTCKDIV,
- RG_PE1_MSTCKDIV_VAL(0x01) | RG_PE1_FRC_MSTCKDIV);
- }
-}
-
-static int mt7621_pci_phy_init(struct phy *phy)
-{
- struct mt7621_pci_phy *mphy = phy_get_drvdata(phy);
-
- if (mphy->bypass_pipe_rst)
- mt7621_bypass_pipe_rst(mphy);
-
- mt7621_set_phy_for_ssc(mphy);
-
- return 0;
-}
-
-static int mt7621_pci_phy_power_on(struct phy *phy)
-{
- struct mt7621_pci_phy *mphy = phy_get_drvdata(phy);
-
- /* Enable PHY and disable force mode */
- mt7621_phy_rmw(mphy, RG_PE1_FRC_PHY_REG,
- RG_PE1_FRC_PHY_EN, RG_PE1_PHY_EN);
-
- if (mphy->has_dual_port) {
- mt7621_phy_rmw(mphy, RG_PE1_FRC_PHY_REG + RG_P0_TO_P1_WIDTH,
- RG_PE1_FRC_PHY_EN, RG_PE1_PHY_EN);
- }
-
- return 0;
-}
-
-static int mt7621_pci_phy_power_off(struct phy *phy)
-{
- struct mt7621_pci_phy *mphy = phy_get_drvdata(phy);
-
- /* Disable PHY */
- mt7621_phy_rmw(mphy, RG_PE1_FRC_PHY_REG,
- RG_PE1_PHY_EN, RG_PE1_FRC_PHY_EN);
-
- if (mphy->has_dual_port) {
- mt7621_phy_rmw(mphy, RG_PE1_FRC_PHY_REG + RG_P0_TO_P1_WIDTH,
- RG_PE1_PHY_EN, RG_PE1_FRC_PHY_EN);
- }
-
- return 0;
-}
-
-static int mt7621_pci_phy_exit(struct phy *phy)
-{
- return 0;
-}
-
-static const struct phy_ops mt7621_pci_phy_ops = {
- .init = mt7621_pci_phy_init,
- .exit = mt7621_pci_phy_exit,
- .power_on = mt7621_pci_phy_power_on,
- .power_off = mt7621_pci_phy_power_off,
- .owner = THIS_MODULE,
-};
-
-static struct phy *mt7621_pcie_phy_of_xlate(struct device *dev,
- struct of_phandle_args *args)
-{
- struct mt7621_pci_phy *mt7621_phy = dev_get_drvdata(dev);
-
- if (WARN_ON(args->args[0] >= MAX_PHYS))
- return ERR_PTR(-ENODEV);
-
- mt7621_phy->has_dual_port = args->args[0];
-
- dev_info(dev, "PHY for 0x%08x (dual port = %d)\n",
- (unsigned int)mt7621_phy->port_base, mt7621_phy->has_dual_port);
-
- return mt7621_phy->phy;
-}
-
-static const struct soc_device_attribute mt7621_pci_quirks_match[] = {
- { .soc_id = "mt7621", .revision = "E2" }
-};
-
-static const struct regmap_config mt7621_pci_phy_regmap_config = {
- .reg_bits = 32,
- .val_bits = 32,
- .reg_stride = 4,
- .max_register = 0x700,
-};
-
-static int mt7621_pci_phy_probe(struct platform_device *pdev)
-{
- struct device *dev = &pdev->dev;
- const struct soc_device_attribute *attr;
- struct phy_provider *provider;
- struct mt7621_pci_phy *phy;
- struct resource *res;
-
- phy = devm_kzalloc(dev, sizeof(*phy), GFP_KERNEL);
- if (!phy)
- return -ENOMEM;
-
- attr = soc_device_match(mt7621_pci_quirks_match);
- if (attr)
- phy->bypass_pipe_rst = true;
-
- phy->dev = dev;
- platform_set_drvdata(pdev, phy);
-
- res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
- if (!res) {
- dev_err(dev, "failed to get address resource\n");
- return -ENXIO;
- }
-
- phy->port_base = devm_ioremap_resource(dev, res);
- if (IS_ERR(phy->port_base)) {
- dev_err(dev, "failed to remap phy regs\n");
- return PTR_ERR(phy->port_base);
- }
-
- phy->regmap = devm_regmap_init_mmio(phy->dev, phy->port_base,
- &mt7621_pci_phy_regmap_config);
- if (IS_ERR(phy->regmap))
- return PTR_ERR(phy->regmap);
-
- phy->phy = devm_phy_create(dev, dev->of_node, &mt7621_pci_phy_ops);
- if (IS_ERR(phy)) {
- dev_err(dev, "failed to create phy\n");
- return PTR_ERR(phy);
- }
-
- phy_set_drvdata(phy->phy, phy);
-
- provider = devm_of_phy_provider_register(dev, mt7621_pcie_phy_of_xlate);
-
- return PTR_ERR_OR_ZERO(provider);
-}
-
-static const struct of_device_id mt7621_pci_phy_ids[] = {
- { .compatible = "mediatek,mt7621-pci-phy" },
- {},
-};
-MODULE_DEVICE_TABLE(of, mt7621_pci_ids);
-
-static struct platform_driver mt7621_pci_phy_driver = {
- .probe = mt7621_pci_phy_probe,
- .driver = {
- .name = "mt7621-pci-phy",
- .of_match_table = of_match_ptr(mt7621_pci_phy_ids),
- },
-};
-
-builtin_platform_driver(mt7621_pci_phy_driver);
-
-MODULE_AUTHOR("Sergio Paracuellos <sergio.paracuellos@gmail.com>");
-MODULE_DESCRIPTION("MediaTek MT7621 PCIe PHY driver");
-MODULE_LICENSE("GPL v2");
--
2.25.1
^ permalink raw reply related [flat|nested] 12+ messages in thread
* Re: [PATCH v4 1/4] dt-bindings: phy: Add binding for Mediatek MT7621 PCIe PHY
2020-10-31 12:22 ` [PATCH v4 1/4] dt-bindings: phy: Add binding for Mediatek " Sergio Paracuellos
@ 2020-11-04 22:30 ` Rob Herring
0 siblings, 0 replies; 12+ messages in thread
From: Rob Herring @ 2020-11-04 22:30 UTC (permalink / raw)
To: Sergio Paracuellos
Cc: vkoul, devel, neil, kishon, devicetree, robh+dt, gregkh
On Sat, 31 Oct 2020 13:22:43 +0100, Sergio Paracuellos wrote:
> Add bindings to describe Mediatek MT7621 PCIe PHY.
>
> Signed-off-by: Sergio Paracuellos <sergio.paracuellos@gmail.com>
> ---
> .../bindings/phy/mediatek,mt7621-pci-phy.yaml | 36 +++++++++++++++++++
> 1 file changed, 36 insertions(+)
> create mode 100644 Documentation/devicetree/bindings/phy/mediatek,mt7621-pci-phy.yaml
>
Reviewed-by: Rob Herring <robh@kernel.org>
^ permalink raw reply [flat|nested] 12+ messages in thread
* Re: [PATCH v4 4/4] staging: mt7621-pci-phy: remove driver from staging
2020-10-31 12:22 ` [PATCH v4 4/4] staging: mt7621-pci-phy: remove driver from staging Sergio Paracuellos
@ 2020-11-06 9:43 ` Greg KH
0 siblings, 0 replies; 12+ messages in thread
From: Greg KH @ 2020-11-06 9:43 UTC (permalink / raw)
To: Sergio Paracuellos; +Cc: kishon, devel, devicetree, vkoul, robh+dt, neil
On Sat, Oct 31, 2020 at 01:22:46PM +0100, Sergio Paracuellos wrote:
> Remove this driver from staging because it has been moved
> into its properly place in the kernel.
>
> Signed-off-by: Sergio Paracuellos <sergio.paracuellos@gmail.com>
> ---
> drivers/staging/Kconfig | 2 -
> drivers/staging/Makefile | 1 -
> drivers/staging/mt7621-pci-phy/Kconfig | 8 -
> drivers/staging/mt7621-pci-phy/Makefile | 2 -
> drivers/staging/mt7621-pci-phy/TODO | 4 -
> .../mediatek,mt7621-pci-phy.yaml | 36 --
> .../staging/mt7621-pci-phy/pci-mt7621-phy.c | 373 ------------------
> 7 files changed, 426 deletions(-)
> delete mode 100644 drivers/staging/mt7621-pci-phy/Kconfig
> delete mode 100644 drivers/staging/mt7621-pci-phy/Makefile
> delete mode 100644 drivers/staging/mt7621-pci-phy/TODO
> delete mode 100644 drivers/staging/mt7621-pci-phy/mediatek,mt7621-pci-phy.yaml
> delete mode 100644 drivers/staging/mt7621-pci-phy/pci-mt7621-phy.c
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
^ permalink raw reply [flat|nested] 12+ messages in thread
* Re: [PATCH v4 0/4] MT7621 PCIe PHY
2020-10-31 12:22 [PATCH v4 0/4] MT7621 PCIe PHY Sergio Paracuellos
` (3 preceding siblings ...)
2020-10-31 12:22 ` [PATCH v4 4/4] staging: mt7621-pci-phy: remove driver from staging Sergio Paracuellos
@ 2020-11-10 12:14 ` Sergio Paracuellos
4 siblings, 0 replies; 12+ messages in thread
From: Sergio Paracuellos @ 2020-11-10 12:14 UTC (permalink / raw)
To: Kishon Vijay Abraham I
Cc: vkoul, Rob Herring, Greg KH,
open list:OPEN FIRMWARE AND FLATTENED DEVICE TREE BINDINGS,
devel, NeilBrown
Hi,
On Sat, Oct 31, 2020 at 1:22 PM Sergio Paracuellos
<sergio.paracuellos@gmail.com> wrote:
>
> This series adds support for the PCIe PHY found in the Mediatek
> MT7621 SoC.
>
> This is the first attempt to get feedback of what is missing in
> this driver to be promoted from staging.
>
> There is also a 'mt7621-pci' driver which is the controller part
> which is still in staging and is a client of this phy.
>
> Both drivers have been tested together in a gnubee1 board.
>
> This series are rebased on the top of linux-next:
> commit 4e78c578cb98 ("Add linux-next specific files for 20201030")
>
> Changes in v4:
> - Bindings moved from txt to yaml so previous Rob's Reviewed-by
> is not in the new patch with the yaml file.
> - 'phy-cells' property means now if phy is dual-ported.
> - Avoid custom 'xlate' function and properly set registers
> when the phy is dual ported.
> - Add use of 'builtin_platform_driver'.
> - Added a patch including myself as maintainer in the
> MAINTAINERS file.
> - Add a patch removing patch from staging to make easier
> the complete inclusion and avoid possible problems might
> appear in 'linux-next' if the series are included.
Kishon, Vinod, any comments on this? Is here something wrong or
missing in order to get this accepted through your tree?
Thanks in advance for your time.
Best regards,
Sergio Paracuellos
>
> Changes in v3:
> - Recollect Rob's Reviewed-by of bindings.
> - Make Kishon Vijay suggested changes in v2:
> (See https://lkml.org/lkml/2019/4/17/53)
> - Kconfig:
> * Add depends on COMPILE_TEST
> * Select REGMAP_MMIO
> - Make use of 'soc_device_attribute' and 'soc_device_match'
> - Use regmap mmio API instead of directly 'readl' and 'writel'.
> - Use 'platform_get_resource' instead of 'of_address_to_resource'.
>
> Changes in v2:
> - Reorder patches to get bindings first in the series.
> - Don't use child nodes in the device tree. Use #phy-cells=1 instead.
> - Update driver code with new 'xlate' function for the new device tree.
> - Minor changes in driver's macros changing some spaces to tabs.
>
> Thanks in advance for your time.
>
> Best regards,
> Sergio Paracuellos
>
> Sergio Paracuellos (4):
> dt-bindings: phy: Add binding for Mediatek MT7621 PCIe PHY
> phy: ralink: Add PHY driver for MT7621 PCIe PHY
> MAINTAINERS: add MT7621 PHY PCI maintainer
> staging: mt7621-pci-phy: remove driver from staging
>
> .../devicetree/bindings/phy}/mediatek,mt7621-pci-phy.yaml | 0
> MAINTAINERS | 6 ++++++
> drivers/phy/ralink/Kconfig | 8 ++++++++
> drivers/phy/ralink/Makefile | 1 +
> .../pci-mt7621-phy.c => phy/ralink/phy-mt7621-pci.c} | 0
> drivers/staging/Kconfig | 2 --
> drivers/staging/Makefile | 1 -
> drivers/staging/mt7621-pci-phy/Kconfig | 8 --------
> drivers/staging/mt7621-pci-phy/Makefile | 2 --
> drivers/staging/mt7621-pci-phy/TODO | 4 ----
> 10 files changed, 15 insertions(+), 17 deletions(-)
> rename {drivers/staging/mt7621-pci-phy => Documentation/devicetree/bindings/phy}/mediatek,mt7621-pci-phy.yaml (100%)
> rename drivers/{staging/mt7621-pci-phy/pci-mt7621-phy.c => phy/ralink/phy-mt7621-pci.c} (100%)
> delete mode 100644 drivers/staging/mt7621-pci-phy/Kconfig
> delete mode 100644 drivers/staging/mt7621-pci-phy/Makefile
> delete mode 100644 drivers/staging/mt7621-pci-phy/TODO
>
> --
> 2.25.1
>
^ permalink raw reply [flat|nested] 12+ messages in thread
* Re: [PATCH v4 2/4] phy: ralink: Add PHY driver for MT7621 PCIe PHY
2020-10-31 12:22 ` [PATCH v4 2/4] phy: ralink: Add PHY driver for " Sergio Paracuellos
@ 2020-11-19 5:30 ` Vinod Koul
2020-11-19 6:05 ` Sergio Paracuellos
0 siblings, 1 reply; 12+ messages in thread
From: Vinod Koul @ 2020-11-19 5:30 UTC (permalink / raw)
To: Sergio Paracuellos; +Cc: kishon, robh+dt, gregkh, devicetree, devel, neil
On 31-10-20, 13:22, Sergio Paracuellos wrote:
> +#define RG_PE1_PIPE_REG 0x02c
> +#define RG_PE1_PIPE_RST BIT(12)
> +#define RG_PE1_PIPE_CMD_FRC BIT(4)
> +
> +#define RG_P0_TO_P1_WIDTH 0x100
> +#define RG_PE1_H_LCDDS_REG 0x49c
> +#define RG_PE1_H_LCDDS_PCW GENMASK(30, 0)
> +#define RG_PE1_H_LCDDS_PCW_VAL(x) ((0x7fffffff & (x)) << 0)
Pls use FIELD_{GET|PREP} instead of coding like this, you already
defined the mask, use it to set and get the reg field ;)
> +
> +#define RG_PE1_FRC_H_XTAL_REG 0x400
> +#define RG_PE1_FRC_H_XTAL_TYPE BIT(8)
> +#define RG_PE1_H_XTAL_TYPE GENMASK(10, 9)
> +#define RG_PE1_H_XTAL_TYPE_VAL(x) ((0x3 & (x)) << 9)
> +
> +#define RG_PE1_FRC_PHY_REG 0x000
> +#define RG_PE1_FRC_PHY_EN BIT(4)
> +#define RG_PE1_PHY_EN BIT(5)
> +
> +#define RG_PE1_H_PLL_REG 0x490
> +#define RG_PE1_H_PLL_BC GENMASK(23, 22)
> +#define RG_PE1_H_PLL_BC_VAL(x) ((0x3 & (x)) << 22)
> +#define RG_PE1_H_PLL_BP GENMASK(21, 18)
> +#define RG_PE1_H_PLL_BP_VAL(x) ((0xf & (x)) << 18)
> +#define RG_PE1_H_PLL_IR GENMASK(15, 12)
> +#define RG_PE1_H_PLL_IR_VAL(x) ((0xf & (x)) << 12)
> +#define RG_PE1_H_PLL_IC GENMASK(11, 8)
> +#define RG_PE1_H_PLL_IC_VAL(x) ((0xf & (x)) << 8)
> +#define RG_PE1_H_PLL_PREDIV GENMASK(7, 6)
> +#define RG_PE1_H_PLL_PREDIV_VAL(x) ((0x3 & (x)) << 6)
> +#define RG_PE1_PLL_DIVEN GENMASK(3, 1)
> +#define RG_PE1_PLL_DIVEN_VAL(x) ((0x7 & (x)) << 1)
> +
> +#define RG_PE1_H_PLL_FBKSEL_REG 0x4bc
> +#define RG_PE1_H_PLL_FBKSEL GENMASK(5, 4)
> +#define RG_PE1_H_PLL_FBKSEL_VAL(x) ((0x3 & (x)) << 4)
> +
> +#define RG_PE1_H_LCDDS_SSC_PRD_REG 0x4a4
> +#define RG_PE1_H_LCDDS_SSC_PRD GENMASK(15, 0)
> +#define RG_PE1_H_LCDDS_SSC_PRD_VAL(x) ((0xffff & (x)) << 0)
> +
> +#define RG_PE1_H_LCDDS_SSC_DELTA_REG 0x4a8
> +#define RG_PE1_H_LCDDS_SSC_DELTA GENMASK(11, 0)
> +#define RG_PE1_H_LCDDS_SSC_DELTA_VAL(x) ((0xfff & (x)) << 0)
> +#define RG_PE1_H_LCDDS_SSC_DELTA1 GENMASK(27, 16)
> +#define RG_PE1_H_LCDDS_SSC_DELTA1_VAL(x) ((0xff & (x)) << 16)
> +
> +#define RG_PE1_LCDDS_CLK_PH_INV_REG 0x4a0
> +#define RG_PE1_LCDDS_CLK_PH_INV BIT(5)
> +
> +#define RG_PE1_H_PLL_BR_REG 0x4ac
> +#define RG_PE1_H_PLL_BR GENMASK(18, 16)
> +#define RG_PE1_H_PLL_BR_VAL(x) ((0x7 & (x)) << 16)
> +
> +#define RG_PE1_MSTCKDIV_REG 0x414
> +#define RG_PE1_MSTCKDIV GENMASK(7, 6)
> +#define RG_PE1_MSTCKDIV_VAL(x) ((0x3 & (x)) << 6)
> +
> +#define RG_PE1_FRC_MSTCKDIV BIT(5)
> +
> +#define XTAL_MODE_SEL_SHIFT 6
Bonus you dont need to define shifts if you use stuff defined in
bitfield.h
> +struct mt7621_pci_phy {
> + struct device *dev;
> + struct regmap *regmap;
> + struct phy *phy;
> + void __iomem *port_base;
> + bool has_dual_port;
> + bool bypass_pipe_rst;
> +};
> +
> +static inline u32 phy_read(struct mt7621_pci_phy *phy, u32 reg)
> +{
> + u32 val;
> +
> + regmap_read(phy->regmap, reg, &val);
> +
> + return val;
> +}
> +
> +static inline void phy_write(struct mt7621_pci_phy *phy, u32 val, u32 reg)
> +{
> + regmap_write(phy->regmap, reg, val);
Why not use regmap_ calls directly and avoid the dummy wrappers..?
> +}
> +
> +static inline void mt7621_phy_rmw(struct mt7621_pci_phy *phy,
> + u32 reg, u32 clr, u32 set)
> +{
> + u32 val = phy_read(phy, reg);
> +
> + val &= ~clr;
> + val |= set;
> + phy_write(phy, val, reg);
why not use regmap_update_bits() instead
> +static void mt7621_set_phy_for_ssc(struct mt7621_pci_phy *phy)
> +{
> + struct device *dev = phy->dev;
> + u32 xtal_mode;
> +
> + xtal_mode = (rt_sysc_r32(SYSC_REG_SYSTEM_CONFIG0)
> + >> XTAL_MODE_SEL_SHIFT) & XTAL_MODE_SEL_MASK;
> +
> + /* Set PCIe Port PHY to disable SSC */
> + /* Debug Xtal Type */
> + mt7621_phy_rmw(phy, RG_PE1_FRC_H_XTAL_REG,
> + RG_PE1_FRC_H_XTAL_TYPE | RG_PE1_H_XTAL_TYPE,
> + RG_PE1_FRC_H_XTAL_TYPE | RG_PE1_H_XTAL_TYPE_VAL(0x00));
> +
> + /* disable port */
> + mt7621_phy_rmw(phy, RG_PE1_FRC_PHY_REG,
> + RG_PE1_PHY_EN, RG_PE1_FRC_PHY_EN);
> +
> + if (phy->has_dual_port) {
> + mt7621_phy_rmw(phy, RG_PE1_FRC_PHY_REG + RG_P0_TO_P1_WIDTH,
> + RG_PE1_PHY_EN, RG_PE1_FRC_PHY_EN);
> + }
> +
> + if (xtal_mode <= 5 && xtal_mode >= 3) { /* 40MHz Xtal */
> + /* Set Pre-divider ratio (for host mode) */
> + mt7621_phy_rmw(phy, RG_PE1_H_PLL_REG,
> + RG_PE1_H_PLL_PREDIV,
> + RG_PE1_H_PLL_PREDIV_VAL(0x01));
> + dev_info(dev, "Xtal is 40MHz\n");
> + } else if (xtal_mode >= 6) { /* 25MHz Xal */
> + mt7621_phy_rmw(phy, RG_PE1_H_PLL_REG,
> + RG_PE1_H_PLL_PREDIV,
> + RG_PE1_H_PLL_PREDIV_VAL(0x00));
> + /* Select feedback clock */
> + mt7621_phy_rmw(phy, RG_PE1_H_PLL_FBKSEL_REG,
> + RG_PE1_H_PLL_FBKSEL,
> + RG_PE1_H_PLL_FBKSEL_VAL(0x01));
> + /* DDS NCPO PCW (for host mode) */
> + mt7621_phy_rmw(phy, RG_PE1_H_LCDDS_SSC_PRD_REG,
> + RG_PE1_H_LCDDS_SSC_PRD,
> + RG_PE1_H_LCDDS_SSC_PRD_VAL(0x18000000));
> + /* DDS SSC dither period control */
> + mt7621_phy_rmw(phy, RG_PE1_H_LCDDS_SSC_PRD_REG,
> + RG_PE1_H_LCDDS_SSC_PRD,
> + RG_PE1_H_LCDDS_SSC_PRD_VAL(0x18d));
> + /* DDS SSC dither amplitude control */
> + mt7621_phy_rmw(phy, RG_PE1_H_LCDDS_SSC_DELTA_REG,
> + RG_PE1_H_LCDDS_SSC_DELTA |
> + RG_PE1_H_LCDDS_SSC_DELTA1,
> + RG_PE1_H_LCDDS_SSC_DELTA_VAL(0x4a) |
> + RG_PE1_H_LCDDS_SSC_DELTA1_VAL(0x4a));
> + dev_info(dev, "Xtal is 25MHz\n");
Debug please
> + } else { /* 20MHz Xtal */
> + mt7621_phy_rmw(phy, RG_PE1_H_PLL_REG,
> + RG_PE1_H_PLL_PREDIV,
> + RG_PE1_H_PLL_PREDIV_VAL(0x00));
> +
> + dev_info(dev, "Xtal is 20MHz\n");
ditto
--
~Vinod
^ permalink raw reply [flat|nested] 12+ messages in thread
* Re: [PATCH v4 2/4] phy: ralink: Add PHY driver for MT7621 PCIe PHY
2020-11-19 5:30 ` Vinod Koul
@ 2020-11-19 6:05 ` Sergio Paracuellos
2020-11-30 12:15 ` Dan Carpenter
0 siblings, 1 reply; 12+ messages in thread
From: Sergio Paracuellos @ 2020-11-19 6:05 UTC (permalink / raw)
To: Vinod Koul
Cc: Kishon Vijay Abraham I, Rob Herring, Greg KH,
open list:OPEN FIRMWARE AND FLATTENED DEVICE TREE BINDINGS,
open list:STAGING SUBSYSTEM, NeilBrown
Hi Vinod,
Thanks for the review.
On Thu, Nov 19, 2020 at 6:31 AM Vinod Koul <vkoul@kernel.org> wrote:
>
> On 31-10-20, 13:22, Sergio Paracuellos wrote:
>
> > +#define RG_PE1_PIPE_REG 0x02c
> > +#define RG_PE1_PIPE_RST BIT(12)
> > +#define RG_PE1_PIPE_CMD_FRC BIT(4)
> > +
> > +#define RG_P0_TO_P1_WIDTH 0x100
> > +#define RG_PE1_H_LCDDS_REG 0x49c
> > +#define RG_PE1_H_LCDDS_PCW GENMASK(30, 0)
> > +#define RG_PE1_H_LCDDS_PCW_VAL(x) ((0x7fffffff & (x)) << 0)
>
> Pls use FIELD_{GET|PREP} instead of coding like this, you already
> defined the mask, use it to set and get the reg field ;)
Will change this and properly remove all of these *_VAL defines.
>
> > +
> > +#define RG_PE1_FRC_H_XTAL_REG 0x400
> > +#define RG_PE1_FRC_H_XTAL_TYPE BIT(8)
> > +#define RG_PE1_H_XTAL_TYPE GENMASK(10, 9)
> > +#define RG_PE1_H_XTAL_TYPE_VAL(x) ((0x3 & (x)) << 9)
> > +
> > +#define RG_PE1_FRC_PHY_REG 0x000
> > +#define RG_PE1_FRC_PHY_EN BIT(4)
> > +#define RG_PE1_PHY_EN BIT(5)
> > +
> > +#define RG_PE1_H_PLL_REG 0x490
> > +#define RG_PE1_H_PLL_BC GENMASK(23, 22)
> > +#define RG_PE1_H_PLL_BC_VAL(x) ((0x3 & (x)) << 22)
> > +#define RG_PE1_H_PLL_BP GENMASK(21, 18)
> > +#define RG_PE1_H_PLL_BP_VAL(x) ((0xf & (x)) << 18)
> > +#define RG_PE1_H_PLL_IR GENMASK(15, 12)
> > +#define RG_PE1_H_PLL_IR_VAL(x) ((0xf & (x)) << 12)
> > +#define RG_PE1_H_PLL_IC GENMASK(11, 8)
> > +#define RG_PE1_H_PLL_IC_VAL(x) ((0xf & (x)) << 8)
> > +#define RG_PE1_H_PLL_PREDIV GENMASK(7, 6)
> > +#define RG_PE1_H_PLL_PREDIV_VAL(x) ((0x3 & (x)) << 6)
> > +#define RG_PE1_PLL_DIVEN GENMASK(3, 1)
> > +#define RG_PE1_PLL_DIVEN_VAL(x) ((0x7 & (x)) << 1)
> > +
> > +#define RG_PE1_H_PLL_FBKSEL_REG 0x4bc
> > +#define RG_PE1_H_PLL_FBKSEL GENMASK(5, 4)
> > +#define RG_PE1_H_PLL_FBKSEL_VAL(x) ((0x3 & (x)) << 4)
> > +
> > +#define RG_PE1_H_LCDDS_SSC_PRD_REG 0x4a4
> > +#define RG_PE1_H_LCDDS_SSC_PRD GENMASK(15, 0)
> > +#define RG_PE1_H_LCDDS_SSC_PRD_VAL(x) ((0xffff & (x)) << 0)
> > +
> > +#define RG_PE1_H_LCDDS_SSC_DELTA_REG 0x4a8
> > +#define RG_PE1_H_LCDDS_SSC_DELTA GENMASK(11, 0)
> > +#define RG_PE1_H_LCDDS_SSC_DELTA_VAL(x) ((0xfff & (x)) << 0)
> > +#define RG_PE1_H_LCDDS_SSC_DELTA1 GENMASK(27, 16)
> > +#define RG_PE1_H_LCDDS_SSC_DELTA1_VAL(x) ((0xff & (x)) << 16)
> > +
> > +#define RG_PE1_LCDDS_CLK_PH_INV_REG 0x4a0
> > +#define RG_PE1_LCDDS_CLK_PH_INV BIT(5)
> > +
> > +#define RG_PE1_H_PLL_BR_REG 0x4ac
> > +#define RG_PE1_H_PLL_BR GENMASK(18, 16)
> > +#define RG_PE1_H_PLL_BR_VAL(x) ((0x7 & (x)) << 16)
> > +
> > +#define RG_PE1_MSTCKDIV_REG 0x414
> > +#define RG_PE1_MSTCKDIV GENMASK(7, 6)
> > +#define RG_PE1_MSTCKDIV_VAL(x) ((0x3 & (x)) << 6)
> > +
> > +#define RG_PE1_FRC_MSTCKDIV BIT(5)
> > +
> > +#define XTAL_MODE_SEL_SHIFT 6
> Bonus you dont need to define shifts if you use stuff defined in
> bitfield.h
I will also check how to remove this SHIFT.
>
> > +struct mt7621_pci_phy {
> > + struct device *dev;
> > + struct regmap *regmap;
> > + struct phy *phy;
> > + void __iomem *port_base;
> > + bool has_dual_port;
> > + bool bypass_pipe_rst;
> > +};
> > +
> > +static inline u32 phy_read(struct mt7621_pci_phy *phy, u32 reg)
> > +{
> > + u32 val;
> > +
> > + regmap_read(phy->regmap, reg, &val);
> > +
> > + return val;
> > +}
> > +
> > +static inline void phy_write(struct mt7621_pci_phy *phy, u32 val, u32 reg)
> > +{
> > + regmap_write(phy->regmap, reg, val);
>
> Why not use regmap_ calls directly and avoid the dummy wrappers..?
This is because name was the dummy names are a bit shorter :) but if
it is also necessary I will use directly regmap_ functions.
>
> > +}
> > +
> > +static inline void mt7621_phy_rmw(struct mt7621_pci_phy *phy,
> > + u32 reg, u32 clr, u32 set)
> > +{
> > + u32 val = phy_read(phy, reg);
> > +
> > + val &= ~clr;
> > + val |= set;
> > + phy_write(phy, val, reg);
>
> why not use regmap_update_bits() instead
True. Will change.
>
> > +static void mt7621_set_phy_for_ssc(struct mt7621_pci_phy *phy)
> > +{
> > + struct device *dev = phy->dev;
> > + u32 xtal_mode;
> > +
> > + xtal_mode = (rt_sysc_r32(SYSC_REG_SYSTEM_CONFIG0)
> > + >> XTAL_MODE_SEL_SHIFT) & XTAL_MODE_SEL_MASK;
> > +
> > + /* Set PCIe Port PHY to disable SSC */
> > + /* Debug Xtal Type */
> > + mt7621_phy_rmw(phy, RG_PE1_FRC_H_XTAL_REG,
> > + RG_PE1_FRC_H_XTAL_TYPE | RG_PE1_H_XTAL_TYPE,
> > + RG_PE1_FRC_H_XTAL_TYPE | RG_PE1_H_XTAL_TYPE_VAL(0x00));
> > +
> > + /* disable port */
> > + mt7621_phy_rmw(phy, RG_PE1_FRC_PHY_REG,
> > + RG_PE1_PHY_EN, RG_PE1_FRC_PHY_EN);
> > +
> > + if (phy->has_dual_port) {
> > + mt7621_phy_rmw(phy, RG_PE1_FRC_PHY_REG + RG_P0_TO_P1_WIDTH,
> > + RG_PE1_PHY_EN, RG_PE1_FRC_PHY_EN);
> > + }
> > +
> > + if (xtal_mode <= 5 && xtal_mode >= 3) { /* 40MHz Xtal */
> > + /* Set Pre-divider ratio (for host mode) */
> > + mt7621_phy_rmw(phy, RG_PE1_H_PLL_REG,
> > + RG_PE1_H_PLL_PREDIV,
> > + RG_PE1_H_PLL_PREDIV_VAL(0x01));
> > + dev_info(dev, "Xtal is 40MHz\n");
> > + } else if (xtal_mode >= 6) { /* 25MHz Xal */
> > + mt7621_phy_rmw(phy, RG_PE1_H_PLL_REG,
> > + RG_PE1_H_PLL_PREDIV,
> > + RG_PE1_H_PLL_PREDIV_VAL(0x00));
> > + /* Select feedback clock */
> > + mt7621_phy_rmw(phy, RG_PE1_H_PLL_FBKSEL_REG,
> > + RG_PE1_H_PLL_FBKSEL,
> > + RG_PE1_H_PLL_FBKSEL_VAL(0x01));
> > + /* DDS NCPO PCW (for host mode) */
> > + mt7621_phy_rmw(phy, RG_PE1_H_LCDDS_SSC_PRD_REG,
> > + RG_PE1_H_LCDDS_SSC_PRD,
> > + RG_PE1_H_LCDDS_SSC_PRD_VAL(0x18000000));
> > + /* DDS SSC dither period control */
> > + mt7621_phy_rmw(phy, RG_PE1_H_LCDDS_SSC_PRD_REG,
> > + RG_PE1_H_LCDDS_SSC_PRD,
> > + RG_PE1_H_LCDDS_SSC_PRD_VAL(0x18d));
> > + /* DDS SSC dither amplitude control */
> > + mt7621_phy_rmw(phy, RG_PE1_H_LCDDS_SSC_DELTA_REG,
> > + RG_PE1_H_LCDDS_SSC_DELTA |
> > + RG_PE1_H_LCDDS_SSC_DELTA1,
> > + RG_PE1_H_LCDDS_SSC_DELTA_VAL(0x4a) |
> > + RG_PE1_H_LCDDS_SSC_DELTA1_VAL(0x4a));
> > + dev_info(dev, "Xtal is 25MHz\n");
>
> Debug please
Will change this trace to debug.
>
> > + } else { /* 20MHz Xtal */
> > + mt7621_phy_rmw(phy, RG_PE1_H_PLL_REG,
> > + RG_PE1_H_PLL_PREDIV,
> > + RG_PE1_H_PLL_PREDIV_VAL(0x00));
> > +
> > + dev_info(dev, "Xtal is 20MHz\n");
>
> ditto
And this one too.
> --
> ~Vinod
Again, thanks for the review. Will change this and send v5 with this
changes and collect ack's and reviewed's from this series.
Best regards,
Sergio Paracuellos
^ permalink raw reply [flat|nested] 12+ messages in thread
* Re: [PATCH v4 2/4] phy: ralink: Add PHY driver for MT7621 PCIe PHY
2020-11-19 6:05 ` Sergio Paracuellos
@ 2020-11-30 12:15 ` Dan Carpenter
2020-11-30 14:34 ` Sergio Paracuellos
0 siblings, 1 reply; 12+ messages in thread
From: Dan Carpenter @ 2020-11-30 12:15 UTC (permalink / raw)
To: Sergio Paracuellos
Cc: Vinod Koul, open list:STAGING SUBSYSTEM,
open list:OPEN FIRMWARE AND FLATTENED DEVICE TREE BINDINGS,
Greg KH, Kishon Vijay Abraham I, Rob Herring, NeilBrown
On Thu, Nov 19, 2020 at 07:05:22AM +0100, Sergio Paracuellos wrote:
> > > +static inline void phy_write(struct mt7621_pci_phy *phy, u32 val, u32 reg)
> > > +{
> > > + regmap_write(phy->regmap, reg, val);
> >
> > Why not use regmap_ calls directly and avoid the dummy wrappers..?
>
> This is because name was the dummy names are a bit shorter :) but if
> it is also necessary I will use directly regmap_ functions.
At least don't swap the last two arguments around.
regards,
dan carpenter
^ permalink raw reply [flat|nested] 12+ messages in thread
* Re: [PATCH v4 2/4] phy: ralink: Add PHY driver for MT7621 PCIe PHY
2020-11-30 12:15 ` Dan Carpenter
@ 2020-11-30 14:34 ` Sergio Paracuellos
0 siblings, 0 replies; 12+ messages in thread
From: Sergio Paracuellos @ 2020-11-30 14:34 UTC (permalink / raw)
To: Dan Carpenter
Cc: Vinod Koul, open list:STAGING SUBSYSTEM,
open list:OPEN FIRMWARE AND FLATTENED DEVICE TREE BINDINGS,
Greg KH, Kishon Vijay Abraham I, Rob Herring, NeilBrown
Hi Dan,
On Mon, Nov 30, 2020 at 1:15 PM Dan Carpenter <dan.carpenter@oracle.com> wrote:
>
> On Thu, Nov 19, 2020 at 07:05:22AM +0100, Sergio Paracuellos wrote:
> > > > +static inline void phy_write(struct mt7621_pci_phy *phy, u32 val, u32 reg)
> > > > +{
> > > > + regmap_write(phy->regmap, reg, val);
> > >
> > > Why not use regmap_ calls directly and avoid the dummy wrappers..?
> >
> > This is because name was the dummy names are a bit shorter :) but if
> > it is also necessary I will use directly regmap_ functions.
>
> At least don't swap the last two arguments around.
You are right. I don't really know why I changed the order there but
those have been deleted in applied series.
>
> regards,
> dan carpenter
Best regards,
Sergio Paracuellos
>
^ permalink raw reply [flat|nested] 12+ messages in thread
end of thread, other threads:[~2020-11-30 14:35 UTC | newest]
Thread overview: 12+ messages (download: mbox.gz / follow: Atom feed)
-- links below jump to the message on this page --
2020-10-31 12:22 [PATCH v4 0/4] MT7621 PCIe PHY Sergio Paracuellos
2020-10-31 12:22 ` [PATCH v4 1/4] dt-bindings: phy: Add binding for Mediatek " Sergio Paracuellos
2020-11-04 22:30 ` Rob Herring
2020-10-31 12:22 ` [PATCH v4 2/4] phy: ralink: Add PHY driver for " Sergio Paracuellos
2020-11-19 5:30 ` Vinod Koul
2020-11-19 6:05 ` Sergio Paracuellos
2020-11-30 12:15 ` Dan Carpenter
2020-11-30 14:34 ` Sergio Paracuellos
2020-10-31 12:22 ` [PATCH v4 3/4] MAINTAINERS: add MT7621 PHY PCI maintainer Sergio Paracuellos
2020-10-31 12:22 ` [PATCH v4 4/4] staging: mt7621-pci-phy: remove driver from staging Sergio Paracuellos
2020-11-06 9:43 ` Greg KH
2020-11-10 12:14 ` [PATCH v4 0/4] MT7621 PCIe PHY Sergio Paracuellos
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).