From: Alan Tull <atull@kernel.org>
To: Moritz Fischer <mdf@kernel.org>
Cc: linux-fpga@vger.kernel.org,
linux-kernel <linux-kernel@vger.kernel.org>,
Rob Herring <robh+dt@kernel.org>,
Mark Rutland <mark.rutland@arm.com>,
Michal Simek <michal.simek@xilinx.com>,
"open list:OPEN FIRMWARE AND FLATTENED DEVICE TREE BINDINGS"
<devicetree@vger.kernel.org>
Subject: Re: [PATCH] dt-bindings: fpga: Consolidate bridge properties
Date: Wed, 21 Feb 2018 12:47:41 -0600 [thread overview]
Message-ID: <CANk1AXRsKgAZYW_qFaC2pxZdbfKQgreOntLNyYm=JmrxN-TTWg@mail.gmail.com> (raw)
In-Reply-To: <20180221173306.17265-1-mdf@kernel.org>
On Wed, Feb 21, 2018 at 11:33 AM, Moritz Fischer <mdf@kernel.org> wrote:
Hi Moritz,
Thanks!
> Consolidate bridge properties in a single file, instead of duplicating
> the same optional property over and over again.
>
> Signed-off-by: Moritz Fischer <mdf@kernel.org>
Acked-by: Alan Tull <atull@kernel.org>
> Cc: Alan Tull <atull@kernel.org>
> Cc: Rob Herring <robh+dt@kernel.org>
> ---
> .../devicetree/bindings/fpga/altera-fpga2sdram-bridge.txt | 5 +----
> .../devicetree/bindings/fpga/altera-freeze-bridge.txt | 5 +----
> .../devicetree/bindings/fpga/altera-hps2fpga-bridge.txt | 5 +----
> Documentation/devicetree/bindings/fpga/fpga-bridge.txt | 15 +++++++++++++++
> .../devicetree/bindings/fpga/xilinx-pr-decoupler.txt | 8 ++------
> 5 files changed, 20 insertions(+), 18 deletions(-)
> create mode 100644 Documentation/devicetree/bindings/fpga/fpga-bridge.txt
>
> diff --git a/Documentation/devicetree/bindings/fpga/altera-fpga2sdram-bridge.txt b/Documentation/devicetree/bindings/fpga/altera-fpga2sdram-bridge.txt
> index 817a8d4bf903..5dd0ff0f7b4e 100644
> --- a/Documentation/devicetree/bindings/fpga/altera-fpga2sdram-bridge.txt
> +++ b/Documentation/devicetree/bindings/fpga/altera-fpga2sdram-bridge.txt
> @@ -3,10 +3,7 @@ Altera FPGA To SDRAM Bridge Driver
> Required properties:
> - compatible : Should contain "altr,socfpga-fpga2sdram-bridge"
>
> -Optional properties:
> -- bridge-enable : 0 if driver should disable bridge at startup
> - 1 if driver should enable bridge at startup
> - Default is to leave bridge in current state.
> +See Documentation/devicetree/bindings/fpga/fpga-bridge.txt for generic bindings.
>
> Example:
> fpga_bridge3: fpga-bridge@ffc25080 {
> diff --git a/Documentation/devicetree/bindings/fpga/altera-freeze-bridge.txt b/Documentation/devicetree/bindings/fpga/altera-freeze-bridge.txt
> index f8e288c71b2d..8b26fbcff3c6 100644
> --- a/Documentation/devicetree/bindings/fpga/altera-freeze-bridge.txt
> +++ b/Documentation/devicetree/bindings/fpga/altera-freeze-bridge.txt
> @@ -10,10 +10,7 @@ Required properties:
> - compatible : Should contain "altr,freeze-bridge-controller"
> - regs : base address and size for freeze bridge module
>
> -Optional properties:
> -- bridge-enable : 0 if driver should disable bridge at startup
> - 1 if driver should enable bridge at startup
> - Default is to leave bridge in current state.
> +See Documentation/devicetree/bindings/fpga/fpga-bridge.txt for generic bindings.
>
> Example:
> freeze-controller@100000450 {
> diff --git a/Documentation/devicetree/bindings/fpga/altera-hps2fpga-bridge.txt b/Documentation/devicetree/bindings/fpga/altera-hps2fpga-bridge.txt
> index 6406f9337eeb..68cce3945b10 100644
> --- a/Documentation/devicetree/bindings/fpga/altera-hps2fpga-bridge.txt
> +++ b/Documentation/devicetree/bindings/fpga/altera-hps2fpga-bridge.txt
> @@ -9,10 +9,7 @@ Required properties:
> - resets : Phandle and reset specifier for this bridge's reset
> - clocks : Clocks used by this module.
>
> -Optional properties:
> -- bridge-enable : 0 if driver should disable bridge at startup.
> - 1 if driver should enable bridge at startup.
> - Default is to leave bridge in its current state.
> +See Documentation/devicetree/bindings/fpga/fpga-bridge.txt for generic bindings.
>
> Example:
> fpga_bridge0: fpga-bridge@ff400000 {
> diff --git a/Documentation/devicetree/bindings/fpga/fpga-bridge.txt b/Documentation/devicetree/bindings/fpga/fpga-bridge.txt
> new file mode 100644
> index 000000000000..82607b23a287
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/fpga/fpga-bridge.txt
> @@ -0,0 +1,15 @@
> +FPGA Bridge Device Tree Binding
> +
> +Moritz Fischer 2018 (Consolidated from previous bindings)
> +
> +Optional properties:
> +- bridge-enable : 0 if driver should disable bridge at startup
> + 1 if driver should enable bridge at startup
> + Default is to leave bridge in current state.
> +
> +Example:
> + fpga_bridge3: fpga-bridge@ffc25080 {
> + compatible = "altr,socfpga-fpga2sdram-bridge";
> + reg = <0xffc25080 0x4>;
> + bridge-enable = <0>;
> + };
> diff --git a/Documentation/devicetree/bindings/fpga/xilinx-pr-decoupler.txt b/Documentation/devicetree/bindings/fpga/xilinx-pr-decoupler.txt
> index 8dcfba926bc7..4284d293fa61 100644
> --- a/Documentation/devicetree/bindings/fpga/xilinx-pr-decoupler.txt
> +++ b/Documentation/devicetree/bindings/fpga/xilinx-pr-decoupler.txt
> @@ -18,12 +18,8 @@ Required properties:
> - clocks : input clock to IP
> - clock-names : should contain "aclk"
>
> -Optional properties:
> -- bridge-enable : 0 if driver should disable bridge at startup
> - 1 if driver should enable bridge at startup
> - Default is to leave bridge in current state.
> -
> -See Documentation/devicetree/bindings/fpga/fpga-region.txt for generic bindings.
> +See Documentation/devicetree/bindings/fpga/fpga-region.txt and
> +Documentation/devicetree/bindings/fpga/fpga-bridge.txt for generic bindings.
>
> Example:
> fpga-bridge@100000450 {
> --
> 2.16.1
>
next prev parent reply other threads:[~2018-02-21 18:47 UTC|newest]
Thread overview: 5+ messages / expand[flat|nested] mbox.gz Atom feed top
2018-02-21 17:33 [PATCH] dt-bindings: fpga: Consolidate bridge properties Moritz Fischer
2018-02-21 18:47 ` Alan Tull [this message]
2018-02-22 7:12 ` Michal Simek
2018-02-22 17:30 ` Moritz Fischer
2018-03-01 22:41 ` Rob Herring
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to='CANk1AXRsKgAZYW_qFaC2pxZdbfKQgreOntLNyYm=JmrxN-TTWg@mail.gmail.com' \
--to=atull@kernel.org \
--cc=devicetree@vger.kernel.org \
--cc=linux-fpga@vger.kernel.org \
--cc=linux-kernel@vger.kernel.org \
--cc=mark.rutland@arm.com \
--cc=mdf@kernel.org \
--cc=michal.simek@xilinx.com \
--cc=robh+dt@kernel.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).