[PATCH v3 0/4] arm64: dts: qcom: sdm845: Add thermal zones for PM8998 ADC

[PATCH v3 0/4] arm64: dts: qcom: sdm845: Add thermal zones for PM8998 ADC

[Bjorn Andersson]

Describe ADC channels, related thermal monitor channels and add thermal
zones for these.

Bjorn Andersson (4):
  dt-bindings: thermal: qcom: add HC variant of adc-thermal monitor
    bindings
  thermal/drivers/qcom/spmi-adc-tm5: Add support for HC variant
  arm64: dts: qcom: pm8998: Add ADC Thermal Monitor node
  arm64: dts: qcom: sdm845: mtp: Add vadc channels and thermal zones

 .../bindings/thermal/qcom-spmi-adc-tm-hc.yaml | 149 ++++++++++++++++++
 arch/arm64/boot/dts/qcom/pm8998.dtsi          |  10 ++
 arch/arm64/boot/dts/qcom/sdm845-mtp.dts       | 140 ++++++++++++++++
 drivers/thermal/qcom/qcom-spmi-adc-tm5.c      |  41 ++++-
 4 files changed, 339 insertions(+), 1 deletion(-)
 create mode 100644 Documentation/devicetree/bindings/thermal/qcom-spmi-adc-tm-hc.yaml

-- 
2.29.2

[PATCH v3 1/4] dt-bindings: thermal: qcom: add HC variant of adc-thermal monitor bindings

[Bjorn Andersson]

The HC generation of the ADC Thermal Monitor is quite similar to the 5th
generation, but differs in valid values for a few properties. Create a
new binding for the HC version of the hardware, rather than sprinkle
conditionals throughout the existing binding.

Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
---

Changes since v2:
- None

 .../bindings/thermal/qcom-spmi-adc-tm-hc.yaml | 149 ++++++++++++++++++
 1 file changed, 149 insertions(+)
 create mode 100644 Documentation/devicetree/bindings/thermal/qcom-spmi-adc-tm-hc.yaml

diff --git a/Documentation/devicetree/bindings/thermal/qcom-spmi-adc-tm-hc.yaml b/Documentation/devicetree/bindings/thermal/qcom-spmi-adc-tm-hc.yaml
new file mode 100644
index 000000000000..8273ac55b63f
--- /dev/null
+++ b/Documentation/devicetree/bindings/thermal/qcom-spmi-adc-tm-hc.yaml
@@ -0,0 +1,149 @@
+# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/thermal/qcom-spmi-adc-tm-hc.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Qualcomm's SPMI PMIC ADC HC Thermal Monitoring
+maintainers:
+  - Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
+
+properties:
+  compatible:
+    const: qcom,spmi-adc-tm-hc
+
+  reg:
+    maxItems: 1
+
+  interrupts:
+    maxItems: 1
+
+  "#thermal-sensor-cells":
+    const: 1
+    description:
+      Number of cells required to uniquely identify the thermal sensors. Since
+      we have multiple sensors this is set to 1
+
+  "#address-cells":
+    const: 1
+
+  "#size-cells":
+    const: 0
+
+  qcom,avg-samples:
+    $ref: /schemas/types.yaml#/definitions/uint32
+    description: Number of samples to be used for measurement.
+    enum:
+      - 1
+      - 2
+      - 4
+      - 8
+      - 16
+    default: 1
+
+  qcom,decimation:
+    $ref: /schemas/types.yaml#/definitions/uint32
+    description: This parameter is used to decrease ADC sampling rate.
+            Quicker measurements can be made by reducing decimation ratio.
+    enum:
+      - 256
+      - 512
+      - 1024
+    default: 1024
+
+patternProperties:
+  "^([-a-z0-9]*)@[0-7]$":
+    type: object
+    description:
+      Represent one thermal sensor.
+
+    properties:
+      reg:
+        description: Specify the sensor channel. There are 8 channels in PMIC5's ADC TM
+        minimum: 0
+        maximum: 7
+
+      io-channels:
+        description:
+          From common IIO binding. Used to pipe PMIC ADC channel to thermal monitor
+
+      qcom,ratiometric:
+        $ref: /schemas/types.yaml#/definitions/flag
+        description:
+          Channel calibration type.
+          If this property is specified VADC will use the VDD reference
+          (1.875V) and GND for channel calibration. If property is not found,
+          channel will be calibrated with 0V and 1.25V reference channels,
+          also known as absolute calibration.
+
+      qcom,hw-settle-time-us:
+        description: Time between AMUX getting configured and the ADC starting conversion.
+        enum: [0, 100, 200, 300, 400, 500, 600, 700, 1000, 2000, 4000, 6000, 8000, 10000]
+
+      qcom,pre-scaling:
+        $ref: /schemas/types.yaml#/definitions/uint32-array
+        description: Used for scaling the channel input signal before the
+          signal is fed to VADC. The configuration for this node is to know the
+          pre-determined ratio and use it for post scaling. It is a pair of
+          integers, denoting the numerator and denominator of the fraction by
+          which input signal is multiplied. For example, <1 3> indicates the
+          signal is scaled down to 1/3 of its value before ADC measurement.  If
+          property is not found default value depending on chip will be used.
+        items:
+          - const: 1
+          - enum: [ 1, 3, 4, 6, 20, 8, 10 ]
+
+    required:
+      - reg
+      - io-channels
+
+    additionalProperties:
+      false
+
+required:
+  - compatible
+  - reg
+  - interrupts
+  - "#address-cells"
+  - "#size-cells"
+  - "#thermal-sensor-cells"
+
+additionalProperties: false
+
+examples:
+  - |
+    #include <dt-bindings/iio/qcom,spmi-vadc.h>
+    #include <dt-bindings/interrupt-controller/irq.h>
+    spmi_bus {
+        #address-cells = <1>;
+        #size-cells = <0>;
+        pm8998_adc: adc@3100 {
+            reg = <0x3100>;
+            compatible = "qcom,spmi-adc-rev2";
+            #address-cells = <1>;
+            #size-cells = <0>;
+            #io-channel-cells = <1>;
+
+            /* Other propreties are omitted */
+            adc-chan@4c {
+                reg = <ADC5_XO_THERM_100K_PU>;
+            };
+        };
+
+        pm8998_adc_tm: adc-tm@3400 {
+            compatible = "qcom,spmi-adc-tm-hc";
+            reg = <0x3400>;
+            interrupts = <0x2 0x34 0x0 IRQ_TYPE_EDGE_RISING>;
+            #thermal-sensor-cells = <1>;
+            #address-cells = <1>;
+            #size-cells = <0>;
+
+            thermistor@1 {
+                reg = <1>;
+                io-channels = <&pm8998_adc ADC5_XO_THERM_100K_PU>;
+                qcom,ratiometric;
+                qcom,hw-settle-time-us = <200>;
+            };
+        };
+    };
+...
-- 
2.29.2

Re: [PATCH v3 1/4] dt-bindings: thermal: qcom: add HC variant of adc-thermal monitor bindings

[Rob Herring]

On Mon, 04 Oct 2021 20:25:28 -0700, Bjorn Andersson wrote:
> The HC generation of the ADC Thermal Monitor is quite similar to the 5th
> generation, but differs in valid values for a few properties. Create a
> new binding for the HC version of the hardware, rather than sprinkle
> conditionals throughout the existing binding.
> 
> Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
> ---
> 
> Changes since v2:
> - None
> 
>  .../bindings/thermal/qcom-spmi-adc-tm-hc.yaml | 149 ++++++++++++++++++
>  1 file changed, 149 insertions(+)
>  create mode 100644 Documentation/devicetree/bindings/thermal/qcom-spmi-adc-tm-hc.yaml
> 

Reviewed-by: Rob Herring <robh@kernel.org>

[PATCH v3 2/4] thermal/drivers/qcom/spmi-adc-tm5: Add support for HC variant

[Bjorn Andersson]

The variant of the ADC Thermal Monitor block found in e.g. PM8998 is
"HC", add support for this variant to the ADC TM5 driver in order to
support using VADC channels as thermal_zones on SDM845 et al.

Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
---

Changes since v2:
- Dropped conditional return ret right before unconditionatl return ret;

 drivers/thermal/qcom/qcom-spmi-adc-tm5.c | 41 +++++++++++++++++++++++-
 1 file changed, 40 insertions(+), 1 deletion(-)

diff --git a/drivers/thermal/qcom/qcom-spmi-adc-tm5.c b/drivers/thermal/qcom/qcom-spmi-adc-tm5.c
index 8494cc04aa21..824671cf494a 100644
--- a/drivers/thermal/qcom/qcom-spmi-adc-tm5.c
+++ b/drivers/thermal/qcom/qcom-spmi-adc-tm5.c
@@ -82,6 +82,7 @@ struct adc_tm5_data {
 	const u32	full_scale_code_volt;
 	unsigned int	*decimation;
 	unsigned int	*hw_settle;
+	bool		is_hc;
 };
 
 enum adc_tm5_cal_method {
@@ -146,6 +147,14 @@ static const struct adc_tm5_data adc_tm5_data_pmic = {
 					 64000, 128000 },
 };
 
+static const struct adc_tm5_data adc_tm_hc_data_pmic = {
+	.full_scale_code_volt = 0x70e4,
+	.decimation = (unsigned int []) { 256, 512, 1024 },
+	.hw_settle = (unsigned int []) { 0, 100, 200, 300, 400, 500, 600, 700,
+					 1000, 2000, 4000, 6000, 8000, 10000 },
+	.is_hc = true,
+};
+
 static int adc_tm5_read(struct adc_tm5_chip *adc_tm, u16 offset, u8 *data, int len)
 {
 	return regmap_bulk_read(adc_tm->regmap, adc_tm->base + offset, data, len);
@@ -375,6 +384,29 @@ static int adc_tm5_register_tzd(struct adc_tm5_chip *adc_tm)
 	return 0;
 }
 
+static int adc_tm_hc_init(struct adc_tm5_chip *chip)
+{
+	unsigned int i;
+	u8 buf[2];
+	int ret;
+
+	for (i = 0; i < chip->nchannels; i++) {
+		if (chip->channels[i].channel >= ADC_TM5_NUM_CHANNELS) {
+			dev_err(chip->dev, "Invalid channel %d\n", chip->channels[i].channel);
+			return -EINVAL;
+		}
+	}
+
+	buf[0] = chip->decimation;
+	buf[1] = chip->avg_samples | ADC_TM5_FAST_AVG_EN;
+
+	ret = adc_tm5_write(chip, ADC_TM5_ADC_DIG_PARAM, buf, sizeof(buf));
+	if (ret)
+		dev_err(chip->dev, "block write failed: %d\n", ret);
+
+	return ret;
+}
+
 static int adc_tm5_init(struct adc_tm5_chip *chip)
 {
 	u8 buf[4], channels_available;
@@ -591,7 +623,10 @@ static int adc_tm5_probe(struct platform_device *pdev)
 		return ret;
 	}
 
-	ret = adc_tm5_init(adc_tm);
+	if (adc_tm->data->is_hc)
+		ret = adc_tm_hc_init(adc_tm);
+	else
+		ret = adc_tm5_init(adc_tm);
 	if (ret) {
 		dev_err(dev, "adc-tm init failed\n");
 		return ret;
@@ -612,6 +647,10 @@ static const struct of_device_id adc_tm5_match_table[] = {
 		.compatible = "qcom,spmi-adc-tm5",
 		.data = &adc_tm5_data_pmic,
 	},
+	{
+		.compatible = "qcom,spmi-adc-tm-hc",
+		.data = &adc_tm_hc_data_pmic,
+	},
 	{ }
 };
 MODULE_DEVICE_TABLE(of, adc_tm5_match_table);
-- 
2.29.2

Re: [PATCH v3 2/4] thermal/drivers/qcom/spmi-adc-tm5: Add support for HC variant

[Dmitry Baryshkov]

On 05/10/2021 06:25, Bjorn Andersson wrote:
> The variant of the ADC Thermal Monitor block found in e.g. PM8998 is
> "HC", add support for this variant to the ADC TM5 driver in order to
> support using VADC channels as thermal_zones on SDM845 et al.
> 
> Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>

Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>

> ---
> 
> Changes since v2:
> - Dropped conditional return ret right before unconditionatl return ret;
> 
>   drivers/thermal/qcom/qcom-spmi-adc-tm5.c | 41 +++++++++++++++++++++++-
>   1 file changed, 40 insertions(+), 1 deletion(-)
> 
> diff --git a/drivers/thermal/qcom/qcom-spmi-adc-tm5.c b/drivers/thermal/qcom/qcom-spmi-adc-tm5.c
> index 8494cc04aa21..824671cf494a 100644
> --- a/drivers/thermal/qcom/qcom-spmi-adc-tm5.c
> +++ b/drivers/thermal/qcom/qcom-spmi-adc-tm5.c
> @@ -82,6 +82,7 @@ struct adc_tm5_data {
>   	const u32	full_scale_code_volt;
>   	unsigned int	*decimation;
>   	unsigned int	*hw_settle;
> +	bool		is_hc;
>   };
>   
>   enum adc_tm5_cal_method {
> @@ -146,6 +147,14 @@ static const struct adc_tm5_data adc_tm5_data_pmic = {
>   					 64000, 128000 },
>   };
>   
> +static const struct adc_tm5_data adc_tm_hc_data_pmic = {
> +	.full_scale_code_volt = 0x70e4,
> +	.decimation = (unsigned int []) { 256, 512, 1024 },
> +	.hw_settle = (unsigned int []) { 0, 100, 200, 300, 400, 500, 600, 700,
> +					 1000, 2000, 4000, 6000, 8000, 10000 },
> +	.is_hc = true,
> +};
> +
>   static int adc_tm5_read(struct adc_tm5_chip *adc_tm, u16 offset, u8 *data, int len)
>   {
>   	return regmap_bulk_read(adc_tm->regmap, adc_tm->base + offset, data, len);
> @@ -375,6 +384,29 @@ static int adc_tm5_register_tzd(struct adc_tm5_chip *adc_tm)
>   	return 0;
>   }
>   
> +static int adc_tm_hc_init(struct adc_tm5_chip *chip)
> +{
> +	unsigned int i;
> +	u8 buf[2];
> +	int ret;
> +
> +	for (i = 0; i < chip->nchannels; i++) {
> +		if (chip->channels[i].channel >= ADC_TM5_NUM_CHANNELS) {
> +			dev_err(chip->dev, "Invalid channel %d\n", chip->channels[i].channel);
> +			return -EINVAL;
> +		}
> +	}
> +
> +	buf[0] = chip->decimation;
> +	buf[1] = chip->avg_samples | ADC_TM5_FAST_AVG_EN;
> +
> +	ret = adc_tm5_write(chip, ADC_TM5_ADC_DIG_PARAM, buf, sizeof(buf));
> +	if (ret)
> +		dev_err(chip->dev, "block write failed: %d\n", ret);
> +
> +	return ret;
> +}
> +
>   static int adc_tm5_init(struct adc_tm5_chip *chip)
>   {
>   	u8 buf[4], channels_available;
> @@ -591,7 +623,10 @@ static int adc_tm5_probe(struct platform_device *pdev)
>   		return ret;
>   	}
>   
> -	ret = adc_tm5_init(adc_tm);
> +	if (adc_tm->data->is_hc)
> +		ret = adc_tm_hc_init(adc_tm);
> +	else
> +		ret = adc_tm5_init(adc_tm);
>   	if (ret) {
>   		dev_err(dev, "adc-tm init failed\n");
>   		return ret;
> @@ -612,6 +647,10 @@ static const struct of_device_id adc_tm5_match_table[] = {
>   		.compatible = "qcom,spmi-adc-tm5",
>   		.data = &adc_tm5_data_pmic,
>   	},
> +	{
> +		.compatible = "qcom,spmi-adc-tm-hc",
> +		.data = &adc_tm_hc_data_pmic,
> +	},
>   	{ }
>   };
>   MODULE_DEVICE_TABLE(of, adc_tm5_match_table);
> 


-- 
With best wishes
Dmitry

[PATCH v3 3/4] arm64: dts: qcom: pm8998: Add ADC Thermal Monitor node

[Bjorn Andersson]

Add a node for the ADC Thermal Monitor found in the PM8998 PMIC. This is
used to connect thermal zones with ADC channels.

Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
---

Changes since v2:
- None

 arch/arm64/boot/dts/qcom/pm8998.dtsi | 10 ++++++++++
 1 file changed, 10 insertions(+)

diff --git a/arch/arm64/boot/dts/qcom/pm8998.dtsi b/arch/arm64/boot/dts/qcom/pm8998.dtsi
index 6f5bb6b37ec2..d09f2954b6f9 100644
--- a/arch/arm64/boot/dts/qcom/pm8998.dtsi
+++ b/arch/arm64/boot/dts/qcom/pm8998.dtsi
@@ -84,6 +84,16 @@ adc-chan@6 {
 			};
 		};
 
+		pm8998_adc_tm: adc-tm@3400 {
+			compatible = "qcom,spmi-adc-tm-hc";
+			reg = <0x3400>;
+			interrupts = <0x0 0x34 0x0 IRQ_TYPE_EDGE_RISING>;
+			#thermal-sensor-cells = <1>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+			status = "disabled";
+		};
+
 		rtc@6000 {
 			compatible = "qcom,pm8941-rtc";
 			reg = <0x6000>, <0x6100>;
-- 
2.29.2

Re: [PATCH v3 3/4] arm64: dts: qcom: pm8998: Add ADC Thermal Monitor node

[Vinod Koul]

On 04-10-21, 20:25, Bjorn Andersson wrote:
> Add a node for the ADC Thermal Monitor found in the PM8998 PMIC. This is
> used to connect thermal zones with ADC channels.

Reviewed-by: Vinod Koul <vkoul@kernel.org>

-- 
~Vinod

[PATCH v3 4/4] arm64: dts: qcom: sdm845: mtp: Add vadc channels and thermal zones

[Bjorn Andersson]

Downstream defines four ADC channels related to thermal sensors external
to the PM8998 and two channels for internal voltage measurements.

Add these to the upstream SDM845 MTP, describe the thermal monitor
channels and add thermal_zones for these.

Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
---

Changes since v2:
- Added missing qcom,ratiometric and qcom,hw-settle-time-us from the ADC channels

 arch/arm64/boot/dts/qcom/sdm845-mtp.dts | 140 ++++++++++++++++++++++++
 1 file changed, 140 insertions(+)

diff --git a/arch/arm64/boot/dts/qcom/sdm845-mtp.dts b/arch/arm64/boot/dts/qcom/sdm845-mtp.dts
index 52dd7a858231..9aa21399b7ee 100644
--- a/arch/arm64/boot/dts/qcom/sdm845-mtp.dts
+++ b/arch/arm64/boot/dts/qcom/sdm845-mtp.dts
@@ -10,6 +10,8 @@
 #include <dt-bindings/gpio/gpio.h>
 #include <dt-bindings/regulator/qcom,rpmh-regulator.h>
 #include "sdm845.dtsi"
+#include "pm8998.dtsi"
+#include "pmi8998.dtsi"
 
 / {
 	model = "Qualcomm Technologies, Inc. SDM845 MTP";
@@ -46,6 +48,68 @@ vreg_s4a_1p8: pm8998-smps4 {
 
 		vin-supply = <&vph_pwr>;
 	};
+
+	thermal-zones {
+		xo_thermal: xo-thermal {
+			polling-delay-passive = <0>;
+			polling-delay = <0>;
+
+			thermal-sensors = <&pm8998_adc_tm 1>;
+
+			trips {
+				trip-point {
+					temperature = <125000>;
+					hysteresis = <10000>;
+					type = "passive";
+				};
+			};
+		};
+
+		msm_thermal: msm-thermal {
+			polling-delay-passive = <0>;
+			polling-delay = <0>;
+
+			thermal-sensors = <&pm8998_adc_tm 2>;
+
+			trips {
+				trip-point {
+					temperature = <125000>;
+					hysteresis = <10000>;
+					type = "passive";
+				};
+			};
+		};
+
+		pa_thermal: pa-thermal {
+			polling-delay-passive = <0>;
+			polling-delay = <0>;
+
+			thermal-sensors = <&pm8998_adc_tm 3>;
+
+			trips {
+				trip-point {
+					temperature = <125000>;
+					hysteresis = <10000>;
+					type = "passive";
+				};
+			};
+		};
+
+		quiet_thermal: quiet-thermal {
+			polling-delay-passive = <0>;
+			polling-delay = <0>;
+
+			thermal-sensors = <&pm8998_adc_tm 4>;
+
+			trips {
+				trip-point {
+					temperature = <125000>;
+					hysteresis = <10000>;
+					type = "passive";
+				};
+			};
+		};
+	};
 };
 
 &adsp_pas {
@@ -469,6 +533,82 @@ &mss_pil {
 	firmware-name = "qcom/sdm845/mba.mbn", "qcom/sdm845/modem.mbn";
 };
 
+&pm8998_adc {
+	adc-chan@4c {
+		reg = <ADC5_XO_THERM_100K_PU>;
+		label = "xo_therm";
+		qcom,ratiometric;
+		qcom,hw-settle-time-us = <200>;
+	};
+
+	adc-chan@4d {
+		reg = <ADC5_AMUX_THM1_100K_PU>;
+		label = "msm_therm";
+		qcom,ratiometric;
+		qcom,hw-settle-time-us = <200>;
+	};
+
+	adc-chan@4f {
+		reg = <ADC5_AMUX_THM3_100K_PU>;
+		label = "pa_therm1";
+		qcom,ratiometric;
+		qcom,hw-settle-time-us = <200>;
+	};
+
+	adc-chan@51 {
+		reg = <ADC5_AMUX_THM5_100K_PU>;
+		label = "quiet_therm";
+		qcom,ratiometric;
+		qcom,hw-settle-time-us = <200>;
+	};
+
+	adc-chan@83 {
+		reg = <ADC5_VPH_PWR>;
+		label = "vph_pwr";
+		qcom,ratiometric;
+		qcom,hw-settle-time-us = <200>;
+	};
+
+	adc-chan@85 {
+		reg = <ADC5_VCOIN>;
+		label = "vcoin";
+		qcom,ratiometric;
+		qcom,hw-settle-time-us = <200>;
+	};
+};
+
+&pm8998_adc_tm {
+	status = "okay";
+
+	xo-thermistor@1 {
+		reg = <1>;
+		io-channels = <&pm8998_adc ADC5_XO_THERM_100K_PU>;
+		qcom,ratiometric;
+		qcom,hw-settle-time-us = <200>;
+	};
+
+	msm-thermistor@2 {
+		reg = <2>;
+		io-channels = <&pm8998_adc ADC5_AMUX_THM1_100K_PU>;
+		qcom,ratiometric;
+		qcom,hw-settle-time-us = <200>;
+	};
+
+	pa-thermistor@3 {
+		reg = <3>;
+		io-channels = <&pm8998_adc ADC5_AMUX_THM3_100K_PU>;
+		qcom,ratiometric;
+		qcom,hw-settle-time-us = <200>;
+	};
+
+	quiet-thermistor@4 {
+		reg = <4>;
+		io-channels = <&pm8998_adc ADC5_AMUX_THM5_100K_PU>;
+		qcom,ratiometric;
+		qcom,hw-settle-time-us = <200>;
+	};
+};
+
 &qupv3_id_1 {
 	status = "okay";
 };
-- 
2.29.2

Re: [PATCH v3 4/4] arm64: dts: qcom: sdm845: mtp: Add vadc channels and thermal zones

[Vinod Koul]

On 04-10-21, 20:25, Bjorn Andersson wrote:
> Downstream defines four ADC channels related to thermal sensors external
> to the PM8998 and two channels for internal voltage measurements.
> 
> Add these to the upstream SDM845 MTP, describe the thermal monitor
> channels and add thermal_zones for these.

Reviewed-by: Vinod Koul <vkoul@kernel.org>

-- 
~Vinod

Re: [PATCH v3 0/4] arm64: dts: qcom: sdm845: Add thermal zones for PM8998 ADC

[Daniel Lezcano]

Hi,

I will pick patches 1 et 2

Thanks

  -- Daniel


On 05/10/2021 05:25, Bjorn Andersson wrote:
> Describe ADC channels, related thermal monitor channels and add thermal
> zones for these.
> 
> Bjorn Andersson (4):
>   dt-bindings: thermal: qcom: add HC variant of adc-thermal monitor
>     bindings
>   thermal/drivers/qcom/spmi-adc-tm5: Add support for HC variant
>   arm64: dts: qcom: pm8998: Add ADC Thermal Monitor node
>   arm64: dts: qcom: sdm845: mtp: Add vadc channels and thermal zones
> 
>  .../bindings/thermal/qcom-spmi-adc-tm-hc.yaml | 149 ++++++++++++++++++
>  arch/arm64/boot/dts/qcom/pm8998.dtsi          |  10 ++
>  arch/arm64/boot/dts/qcom/sdm845-mtp.dts       | 140 ++++++++++++++++
>  drivers/thermal/qcom/qcom-spmi-adc-tm5.c      |  41 ++++-
>  4 files changed, 339 insertions(+), 1 deletion(-)
>  create mode 100644 Documentation/devicetree/bindings/thermal/qcom-spmi-adc-tm-hc.yaml
> 


-- 
<http://www.linaro.org/> Linaro.org │ Open source software for ARM SoCs

Follow Linaro:  <http://www.facebook.com/pages/Linaro> Facebook |
<http://twitter.com/#!/linaroorg> Twitter |
<http://www.linaro.org/linaro-blog/> Blog

Re: (subset) [PATCH v3 0/4] arm64: dts: qcom: sdm845: Add thermal zones for PM8998 ADC

[Bjorn Andersson]

On Mon, 4 Oct 2021 20:25:27 -0700, Bjorn Andersson wrote:
> Describe ADC channels, related thermal monitor channels and add thermal
> zones for these.
> 
> Bjorn Andersson (4):
>   dt-bindings: thermal: qcom: add HC variant of adc-thermal monitor
>     bindings
>   thermal/drivers/qcom/spmi-adc-tm5: Add support for HC variant
>   arm64: dts: qcom: pm8998: Add ADC Thermal Monitor node
>   arm64: dts: qcom: sdm845: mtp: Add vadc channels and thermal zones
> 
> [...]

Applied, thanks!

[3/4] arm64: dts: qcom: pm8998: Add ADC Thermal Monitor node
      commit: 4cc7c85cccc87e436a86b4281ddcd886eb0bf58f
[4/4] arm64: dts: qcom: sdm845: mtp: Add vadc channels and thermal zones
      commit: d5e12f3823aed1e35ee2411bdf0ab61dc1011387

Best regards,
-- 
Bjorn Andersson <bjorn.andersson@linaro.org>