* [PATCH v4 00/78] drm/vc4: Support BCM2711 Display Pipeline
@ 2020-07-08 17:41 ` Maxime Ripard
2020-07-10 7:37 ` Jian-Hong Pan
` (3 more replies)
0 siblings, 4 replies; 7+ messages in thread
From: Maxime Ripard @ 2020-07-08 17:41 UTC (permalink / raw)
To: Nicolas Saenz Julienne, Eric Anholt
Cc: dri-devel, linux-rpi-kernel, bcm-kernel-feedback-list,
linux-arm-kernel, linux-kernel, Dave Stevenson, Tim Gover,
Phil Elwell, Maxime Ripard, devicetree, Kamal Dasu, linux-clk,
Michael Turquette, Philipp Zabel, Rob Herring, Stephen Boyd
Hi everyone,
Here's a (pretty long) series to introduce support in the VC4 DRM driver
for the display pipeline found in the BCM2711 (and thus the RaspberryPi 4).
The main differences are that there's two HDMI controllers and that there's
more pixelvalve now. Those pixelvalve come with a mux in the HVS that still
have only 3 FIFOs. Both of those differences are breaking a bunch of
expectations in the driver, so we first need a good bunch of cleanup and
reworks to introduce support for the new controllers.
Similarly, the HDMI controller has all its registers shuffled and split in
multiple controllers now, so we need a bunch of changes to support this as
well.
Only the HDMI support is enabled for now (even though the DPI and DSI
outputs have been tested too).
Let me know if you have any comments
Maxime
Cc: bcm-kernel-feedback-list@broadcom.com
Cc: devicetree@vger.kernel.org
Cc: Kamal Dasu <kdasu.kdev@gmail.com>
Cc: linux-clk@vger.kernel.org
Cc: Michael Turquette <mturquette@baylibre.com>
Cc: Philipp Zabel <p.zabel@pengutronix.de>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Stephen Boyd <sboyd@kernel.org>
Changes from v3:
- Rebased on top of next-20200708
- Added a name to the HDMI audio codec component
- Only disable the BCM2711 HDMI pixelvalves at boot
- Fixed an error in the HVS binding
- Fix a framebuffer size condition that was inverted
- Changed the channel allocation algorithm using Eric's suggestion
- Always write the muxing values instead of updating if needed
- Improved a bit the hvs_available_channels comment in the structure
- Change atomic_complete_commit code to use for_each_new_crtc_in_state
- Change the muxing code to take into account disparities between the
BCM2711 and previous SoCs.
- Only change the clock rate on BCM2711 during a modeset
- Fix a crash at atomic_disable
- Use clk_set_min_rate for the core clock too
- Add a few defines, and simplify the FIFO level stuff
- Reordered the patches according to Eric's reviews
- Fixed a regression with VID_CTL setting on RPI3
Changes from v2:
- Rebased on top of next-20200526
- Split the firmware clock series away
- Removed the stuck pixel (with all the subsequent pixels being shifted
by one
- Fixed the writeback issue too.
- Fix the dual output
- Fixed the return value of phy_get_cp_current
- Enhanced the comment on the reset delay
- Increase the max width and height
- Made a proper Kconfig option for the DVP clock driver
- Fixed the alsa card name collision
Changes from v1:
- Rebased on top of 5.7-rc1
- Run checkpatch
- Added audio support
- Fixed some HDMI timeouts
- Swiched to clk_hw_register_gate_parent_data
- Reorder Kconfig symbols in drivers/i2c/busses
- Make the firmware clocks a child of the firmware node
- Switch DVP clock driver to clk_hw interface
- constify raspberrypi_clk_data in raspberrypi_clock_property
- Don't mark firmware clocks as IGNORE_UNUSED
- Change from reset_ms to reset_us in reset-simple, and add a bit more
comments
- Remove generic clk patch to test if a NULL pointer is returned
- Removed misleading message in the is_prepared renaming patch commit
message
- Constify HDMI controller variants
- Fix a bug in the allocation size of the clk data array
- Added a mention in the DT binding conversion patches about the breakage
- Merged a few fixes from kbuild
- Fixed a few bisection and CEC build issues
- Collected Acked-by and Reviewed-by
- Change Dave email address to raspberrypi.com
Dave Stevenson (7):
drm/vc4: Add support for the BCM2711 HVS5
drm/vc4: plane: Change LBM alignment constraint on LBM
drm/vc4: plane: Optimize the LBM allocation size
drm/vc4: hdmi: Use reg-names to retrieve the HDMI audio registers
drm/vc4: hdmi: Reset audio infoframe on encoder_enable if previously streaming
drm/vc4: hdmi: Set the b-frame marker to the match ALSA's default.
drm/vc4: hdmi: Add audio-related callbacks
Maxime Ripard (71):
dt-bindings: display: Add support for the BCM2711 HVS
drm/vc4: hvs: Boost the core clock during modeset
drm/vc4: plane: Create more planes
drm/vc4: crtc: Deal with different number of pixel per clock
drm/vc4: crtc: Use a shared interrupt
drm/vc4: crtc: Move the cob allocation outside of bind
drm/vc4: crtc: Rename HVS channel to output
drm/vc4: crtc: Use local chan variable
drm/vc4: crtc: Enable and disable the PV in atomic_enable / disable
drm/vc4: kms: Convert to for_each_new_crtc_state
drm/vc4: crtc: Assign output to channel automatically
drm/vc4: crtc: Add FIFO depth to vc4_crtc_data
drm/vc4: crtc: Add function to compute FIFO level bits
drm/vc4: crtc: Rename HDMI encoder type to HDMI0
drm/vc4: crtc: Add HDMI1 encoder type
drm/vc4: crtc: Disable color management for HVS5
drm/vc4: crtc: Turn pixelvalve reset into a function
drm/vc4: crtc: Move PV dump to config_pv
drm/vc4: crtc: Move HVS init and close to a function
drm/vc4: crtc: Move the HVS gamma LUT setup to our init function
drm/vc4: hvs: Make sure our channel is reset
drm/vc4: crtc: Remove mode_set_nofb
drm/vc4: crtc: Remove redundant pixelvalve reset
drm/vc4: crtc: Move HVS channel init before the PV initialisation
drm/vc4: encoder: Add finer-grained encoder callbacks
drm/vc4: crtc: Add a delay after disabling the PixelValve output
drm/vc4: crtc: Clear the PixelValve FIFO on disable
drm/vc4: crtc: Clear the PixelValve FIFO during configuration
drm/vc4: hvs: Make the stop_channel function public
drm/vc4: hvs: Introduce a function to get the assigned FIFO
drm/vc4: crtc: Move the CRTC disable out
drm/vc4: drv: Disable the CRTC at boot time
dt-bindings: display: vc4: pv: Add BCM2711 pixel valves
drm/vc4: crtc: Add BCM2711 pixelvalves
drm/vc4: hdmi: Use debugfs private field
drm/vc4: hdmi: Move structure to header
drm/vc4: hdmi: rework connectors and encoders
drm/vc4: hdmi: Remove DDC argument to connector_init
drm/vc4: hdmi: Rename hdmi to vc4_hdmi
drm/vc4: hdmi: Move accessors to vc4_hdmi
drm/vc4: hdmi: Use local vc4_hdmi directly
drm/vc4: hdmi: Add container_of macros for encoders and connectors
drm/vc4: hdmi: Pass vc4_hdmi to CEC code
drm/vc4: hdmi: Retrieve the vc4_hdmi at unbind using our device
drm/vc4: hdmi: Remove vc4_dev hdmi pointer
drm/vc4: hdmi: Remove vc4_hdmi_connector
drm/vc4: hdmi: Introduce resource init and variant
drm/vc4: hdmi: Implement a register layout abstraction
drm/vc4: hdmi: Add reset callback
drm/vc4: hdmi: Add PHY init and disable function
drm/vc4: hdmi: Add PHY RNG enable / disable function
drm/vc4: hdmi: Add a CSC setup callback
drm/vc4: hdmi: Store the encoder type in the variant structure
drm/vc4: hdmi: Deal with multiple debugfs files
drm/vc4: hdmi: Move CEC init to its own function
drm/vc4: hdmi: Add CEC support flag
drm/vc4: hdmi: Remove unused CEC_CLOCK_DIV define
drm/vc4: hdmi: Rename drm_encoder pointer in mode_valid
drm/vc4: hdmi: Adjust HSM clock rate depending on pixel rate
drm/vc4: hdmi: Use clk_set_min_rate instead
drm/vc4: hdmi: Deal with multiple ALSA cards
drm/vc4: hdmi: Remove register dumps in enable
drm/vc4: hdmi: Always recenter the HDMI FIFO
drm/vc4: hdmi: Implement finer-grained hooks
drm/vc4: hdmi: Do the VID_CTL configuration at once
drm/vc4: hdmi: Switch to blank pixels when disabled
drm/vc4: hdmi: Support the BCM2711 HDMI controllers
dt-bindings: display: vc4: hdmi: Add BCM2711 HDMI controllers bindings
dt-bindings: display: vc4: Document BCM2711 VC5
drm/vc4: drv: Support BCM2711
ARM: dts: bcm2711: Enable the display pipeline
Documentation/devicetree/bindings/display/brcm,bcm2711-hdmi.yaml | 109 +++++-
Documentation/devicetree/bindings/display/brcm,bcm2835-hvs.yaml | 18 +-
Documentation/devicetree/bindings/display/brcm,bcm2835-pixelvalve0.yaml | 5 +-
Documentation/devicetree/bindings/display/brcm,bcm2835-vc4.yaml | 1 +-
arch/arm/boot/dts/bcm2711-rpi-4-b.dts | 46 ++-
arch/arm/boot/dts/bcm2711.dtsi | 115 ++++-
drivers/gpu/drm/vc4/Makefile | 1 +-
drivers/gpu/drm/vc4/vc4_crtc.c | 338 +++++++++++----
drivers/gpu/drm/vc4/vc4_drv.c | 5 +-
drivers/gpu/drm/vc4/vc4_drv.h | 43 +-
drivers/gpu/drm/vc4/vc4_hdmi.c | 1625 +++++++++++++++++++++++++++++++++++++++++++-----------------------------
drivers/gpu/drm/vc4/vc4_hdmi.h | 183 ++++++++-
drivers/gpu/drm/vc4/vc4_hdmi_phy.c | 520 +++++++++++++++++++++++-
drivers/gpu/drm/vc4/vc4_hdmi_regs.h | 442 ++++++++++++++++++++-
drivers/gpu/drm/vc4/vc4_hvs.c | 260 +++++++-----
drivers/gpu/drm/vc4/vc4_kms.c | 225 +++++++++-
drivers/gpu/drm/vc4/vc4_plane.c | 222 +++++++---
drivers/gpu/drm/vc4/vc4_regs.h | 177 +++-----
drivers/gpu/drm/vc4/vc4_txp.c | 4 +-
19 files changed, 3331 insertions(+), 1008 deletions(-)
create mode 100644 Documentation/devicetree/bindings/display/brcm,bcm2711-hdmi.yaml
create mode 100644 drivers/gpu/drm/vc4/vc4_hdmi.h
create mode 100644 drivers/gpu/drm/vc4/vc4_hdmi_phy.c
create mode 100644 drivers/gpu/drm/vc4/vc4_hdmi_regs.h
base-commit: 5bdd2824d705fb8d339d6f96e464b907c9a1553d
--
git-series 0.9.1
^ permalink raw reply [flat|nested] 7+ messages in thread
* Re: [PATCH v4 00/78] drm/vc4: Support BCM2711 Display Pipeline
2020-07-08 17:41 ` [PATCH v4 00/78] drm/vc4: Support BCM2711 Display Pipeline Maxime Ripard
@ 2020-07-10 7:37 ` Jian-Hong Pan
2020-07-10 9:58 ` Stefan Wahren
` (2 subsequent siblings)
3 siblings, 0 replies; 7+ messages in thread
From: Jian-Hong Pan @ 2020-07-10 7:37 UTC (permalink / raw)
To: maxime
Cc: bcm-kernel-feedback-list, dave.stevenson, devicetree, dri-devel,
eric, kdasu.kdev, linux-arm-kernel, linux-clk, linux-kernel,
linux-rpi-kernel, mturquette, nsaenzjulienne, phil, robh+dt,
sboyd, tim.gover, linux
Hi Maxime,
Thanks for your version 4 patch again.
I took the patches and applied them upon next-20200708.
I make system cold reboot to multi-user target and the text console shows on the
screen. Then, I simply hot re-plug the HDMI cable on HDMI0 port, I not only lose
the text console on the screen (the display shows blank, backlight is off), but
also kernel does not probe modes for the HDMI connector again.
But HDMI1 does probe modes again for hot re-plugging. So, HDMI1 does not hit the
issue like HDMI0.
* System probes modes only once for HDMI0 port (HDMI-A-1), even hot re-plug HDMI
cable to the same port:
[ 15.611072] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:32:HDMI-A-1] probed modes :
[ 15.611079] [drm:drm_mode_debug_printmodeline] Modeline "1920x1080": 60 148500 1920 2008 2052 2200 1080 1084 1089 1125 0x48 0x5
[ 15.611085] [drm:drm_mode_debug_printmodeline] Modeline "1920x1080": 60 148500 1920 2008 2052 2200 1080 1084 1089 1125 0x40 0x5
...
[ 15.611298] [drm:drm_mode_debug_printmodeline] Modeline "720x400": 70 28320 720 738 846 900 400 412 414 449 0x40 0x6
[ 15.611303] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:38:HDMI-A-2]
[ 15.612184] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:38:HDMI-A-2] disconnected
[ 15.612191] [drm:drm_client_modeset_probe] connector 32 enabled? yes
[ 15.612194] [drm:drm_client_modeset_probe] connector 38 enabled? no
[ 15.612206] [drm:drm_client_modeset_probe] Not using firmware configuration
[ 15.612213] [drm:drm_client_modeset_probe] looking for cmdline mode on connector 32
[ 15.612218] [drm:drm_client_modeset_probe] looking for preferred mode on connector 32 0
[ 15.612221] [drm:drm_client_modeset_probe] found mode 1920x1080
...
[ 108.263384] [drm:output_poll_execute] [CONNECTOR:32:HDMI-A-1] status updated from disconnected to connected
[ 108.264307] vc4-drm gpu: [drm:drm_fb_helper_hotplug_event.part.0]
[ 108.264312] [drm:drm_client_modeset_probe]
[ 108.264321] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:32:HDMI-A-1]
[ 109.303379] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:38:HDMI-A-2]
[ 109.304258] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:38:HDMI-A-2] disconnected
[ 109.304266] [drm:drm_client_modeset_probe] No connectors reported connected with modes
* System probes modes again for HDMI1 port (HDMI-A-2), whenever hot re-plug the
HDMI cable:
[ 797.974649] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:38:HDMI-A-2] probed modes :
[ 797.974656] [drm:drm_mode_debug_printmodeline] Modeline "1920x1080": 60 148500 1920 2008 2052 2200 1080 1084 1089 1125 0x48 0x5
[ 797.974662] [drm:drm_mode_debug_printmodeline] Modeline "1920x1080": 60 148500 1920 2008 2052 2200 1080 1084 1089 1125 0x40 0x5
...
[ 797.974874] [drm:drm_mode_debug_printmodeline] Modeline "720x400": 70 28320 720 738 846 900 400 412 414 449 0x40 0x6
[ 797.974880] [drm:drm_client_modeset_probe] connector 32 enabled? no
[ 797.974883] [drm:drm_client_modeset_probe] connector 38 enabled? yes
[ 797.974895] [drm:drm_client_modeset_probe] Not using firmware configuration
[ 797.974901] [drm:drm_client_modeset_probe] looking for cmdline mode on connector 38
[ 797.974905] [drm:drm_client_modeset_probe] looking for preferred mode on connector 38 0
[ 797.974908] [drm:drm_client_modeset_probe] found mode 1920x1080
...
[ 852.242615] vc4-drm gpu: [drm:drm_client_dev_hotplug] fbdev: ret=0
[ 873.718277] [drm:output_poll_execute] [CONNECTOR:38:HDMI-A-2] status updated from disconnected to connected
[ 873.718332] vc4-drm gpu: [drm:drm_fb_helper_hotplug_event.part.0]
[ 873.718338] [drm:drm_client_modeset_probe]
...
[ 874.264013] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:38:HDMI-A-2] probed modes :
[ 874.264020] [drm:drm_mode_debug_printmodeline] Modeline "1920x1080": 60 148500 1920 2008 2052 2200 1080 1084 1089 1125 0x48 0x5
[ 874.264026] [drm:drm_mode_debug_printmodeline] Modeline "1920x1080": 60 148500 1920 2008 2052 2200 1080 1084 1089 1125 0x40 0x5
...
[ 874.264239] [drm:drm_mode_debug_printmodeline] Modeline "720x400": 70 28320 720 738 846 900 400 412 414 449 0x40 0x6
[ 874.264244] [drm:drm_client_modeset_probe] connector 32 enabled? no
[ 874.264247] [drm:drm_client_modeset_probe] connector 38 enabled? yes
[ 874.264259] [drm:drm_client_modeset_probe] Not using firmware configuration
[ 874.264264] [drm:drm_client_modeset_probe] looking for cmdline mode on connector 38
[ 874.264268] [drm:drm_client_modeset_probe] looking for preferred mode on connector 38 0
[ 874.264272] [drm:drm_client_modeset_probe] found mode 1920x1080
Here is the full dmesg: https://gist.github.com/starnight/5ffb86af552fedb9b6e5741d0540a878#file-dmesg-v4-log
^ permalink raw reply [flat|nested] 7+ messages in thread
* Re: [PATCH v4 00/78] drm/vc4: Support BCM2711 Display Pipeline
2020-07-08 17:41 ` [PATCH v4 00/78] drm/vc4: Support BCM2711 Display Pipeline Maxime Ripard
2020-07-10 7:37 ` Jian-Hong Pan
@ 2020-07-10 9:58 ` Stefan Wahren
2020-08-21 7:18 ` Hoegeun Kwon
2020-08-31 2:36 ` Chanwoo Choi
3 siblings, 0 replies; 7+ messages in thread
From: Stefan Wahren @ 2020-07-10 9:58 UTC (permalink / raw)
To: Maxime Ripard, Nicolas Saenz Julienne, Eric Anholt
Cc: devicetree, Tim Gover, Dave Stevenson, Stephen Boyd,
Michael Turquette, Kamal Dasu, linux-kernel, dri-devel,
linux-clk, Rob Herring, bcm-kernel-feedback-list,
linux-rpi-kernel, Philipp Zabel, Phil Elwell, linux-arm-kernel
Hi Maxime,
Am 08.07.20 um 19:41 schrieb Maxime Ripard:
> Hi everyone,
>
> Here's a (pretty long) series to introduce support in the VC4 DRM driver
> for the display pipeline found in the BCM2711 (and thus the RaspberryPi 4).
>
> The main differences are that there's two HDMI controllers and that there's
> more pixelvalve now. Those pixelvalve come with a mux in the HVS that still
> have only 3 FIFOs. Both of those differences are breaking a bunch of
> expectations in the driver, so we first need a good bunch of cleanup and
> reworks to introduce support for the new controllers.
>
> Similarly, the HDMI controller has all its registers shuffled and split in
> multiple controllers now, so we need a bunch of changes to support this as
> well.
>
> Only the HDMI support is enabled for now (even though the DPI and DSI
> outputs have been tested too).
>
> Let me know if you have any comments
> Maxime
>
> Cc: bcm-kernel-feedback-list@broadcom.com
> Cc: devicetree@vger.kernel.org
> Cc: Kamal Dasu <kdasu.kdev@gmail.com>
> Cc: linux-clk@vger.kernel.org
> Cc: Michael Turquette <mturquette@baylibre.com>
> Cc: Philipp Zabel <p.zabel@pengutronix.de>
> Cc: Rob Herring <robh+dt@kernel.org>
> Cc: Stephen Boyd <sboyd@kernel.org>
>
> Changes from v3:
> - Rebased on top of next-20200708
> - Added a name to the HDMI audio codec component
> - Only disable the BCM2711 HDMI pixelvalves at boot
> - Fixed an error in the HVS binding
> - Fix a framebuffer size condition that was inverted
> - Changed the channel allocation algorithm using Eric's suggestion
> - Always write the muxing values instead of updating if needed
> - Improved a bit the hvs_available_channels comment in the structure
> - Change atomic_complete_commit code to use for_each_new_crtc_in_state
> - Change the muxing code to take into account disparities between the
> BCM2711 and previous SoCs.
> - Only change the clock rate on BCM2711 during a modeset
> - Fix a crash at atomic_disable
> - Use clk_set_min_rate for the core clock too
> - Add a few defines, and simplify the FIFO level stuff
> - Reordered the patches according to Eric's reviews
> - Fixed a regression with VID_CTL setting on RPI3
>
i additionally applied "drm/vc4/vc4_hdmi: fill ASoC card owner" on top
of your series (potential merge conflict).
I didn't see any issues with a RPI 3B or RPI 4B.
So this whole series is
Tested-by: Stefan Wahren <stefan.wahren@i2se.com>
Regards
Stefan
^ permalink raw reply [flat|nested] 7+ messages in thread
* Re: [PATCH v4 00/78] drm/vc4: Support BCM2711 Display Pipeline
2020-07-08 17:41 ` [PATCH v4 00/78] drm/vc4: Support BCM2711 Display Pipeline Maxime Ripard
2020-07-10 7:37 ` Jian-Hong Pan
2020-07-10 9:58 ` Stefan Wahren
@ 2020-08-21 7:18 ` Hoegeun Kwon
2020-09-02 13:32 ` Maxime Ripard
2020-08-31 2:36 ` Chanwoo Choi
3 siblings, 1 reply; 7+ messages in thread
From: Hoegeun Kwon @ 2020-08-21 7:18 UTC (permalink / raw)
To: Maxime Ripard, Nicolas Saenz Julienne, Eric Anholt
Cc: devicetree, Tim Gover, Dave Stevenson, Stephen Boyd,
Michael Turquette, Kamal Dasu, linux-kernel, dri-devel,
linux-clk, Rob Herring, bcm-kernel-feedback-list,
linux-rpi-kernel, Phil Elwell, linux-arm-kernel, Hoegeun Kwon
Hi Maxime,
Thank you for your version 4 patch.
I tested all 78 patches based on the next-20200708.
Dual HDMI opearation does not work normally.
flip_done timed out occurs and doesn't work.
Could you check please it.
[ 105.694541] [drm:drm_atomic_helper_wait_for_dependencies] *ERROR*
[CRTC:64:crtc-3] flip_done timed out
[ 115.934994] [drm:drm_atomic_helper_wait_for_dependencies] *ERROR*
[CONNECTOR:32:HDMI-A-1] flip_done timed out
[ 126.174545] [drm:drm_atomic_helper_wait_for_dependencies] *ERROR*
[PLANE:60:plane-3] flip_done timed out
And there is a problem with 4k UDH not outputting...
So this problem worked as I fixed it like patches[1].
[1] [PATCH 0/3] drm/vc4: Support HDMI QHD or higher output
"[PATCH v4 00/78] drm/vc4: Support BCM2711 Display Pipeline" all patches.
Tested-by: Hoegeun Kwon <hoegeun.kwon@samsung.com>
Best regards,
Hoegeun
> Hi everyone,
>
> Here's a (pretty long) series to introduce support in the VC4 DRM driver
> for the display pipeline found in the BCM2711 (and thus the RaspberryPi 4).
>
> The main differences are that there's two HDMI controllers and that there's
> more pixelvalve now. Those pixelvalve come with a mux in the HVS that still
> have only 3 FIFOs. Both of those differences are breaking a bunch of
> expectations in the driver, so we first need a good bunch of cleanup and
> reworks to introduce support for the new controllers.
>
> Similarly, the HDMI controller has all its registers shuffled and split in
> multiple controllers now, so we need a bunch of changes to support this as
> well.
>
> Only the HDMI support is enabled for now (even though the DPI and DSI
> outputs have been tested too).
>
> Let me know if you have any comments
> Maxime
>
> Cc: bcm-kernel-feedback-list@broadcom.com
> Cc: devicetree@vger.kernel.org
> Cc: Kamal Dasu <kdasu.kdev@gmail.com>
> Cc: linux-clk@vger.kernel.org
> Cc: Michael Turquette <mturquette@baylibre.com>
> Cc: Philipp Zabel <p.zabel@pengutronix.de>
> Cc: Rob Herring <robh+dt@kernel.org>
> Cc: Stephen Boyd <sboyd@kernel.org>
>
> Changes from v3:
> - Rebased on top of next-20200708
> - Added a name to the HDMI audio codec component
> - Only disable the BCM2711 HDMI pixelvalves at boot
> - Fixed an error in the HVS binding
> - Fix a framebuffer size condition that was inverted
> - Changed the channel allocation algorithm using Eric's suggestion
> - Always write the muxing values instead of updating if needed
> - Improved a bit the hvs_available_channels comment in the structure
> - Change atomic_complete_commit code to use for_each_new_crtc_in_state
> - Change the muxing code to take into account disparities between the
> BCM2711 and previous SoCs.
> - Only change the clock rate on BCM2711 during a modeset
> - Fix a crash at atomic_disable
> - Use clk_set_min_rate for the core clock too
> - Add a few defines, and simplify the FIFO level stuff
> - Reordered the patches according to Eric's reviews
> - Fixed a regression with VID_CTL setting on RPI3
>
> Changes from v2:
> - Rebased on top of next-20200526
> - Split the firmware clock series away
> - Removed the stuck pixel (with all the subsequent pixels being shifted
> by one
> - Fixed the writeback issue too.
> - Fix the dual output
> - Fixed the return value of phy_get_cp_current
> - Enhanced the comment on the reset delay
> - Increase the max width and height
> - Made a proper Kconfig option for the DVP clock driver
> - Fixed the alsa card name collision
>
> Changes from v1:
> - Rebased on top of 5.7-rc1
> - Run checkpatch
> - Added audio support
> - Fixed some HDMI timeouts
> - Swiched to clk_hw_register_gate_parent_data
> - Reorder Kconfig symbols in drivers/i2c/busses
> - Make the firmware clocks a child of the firmware node
> - Switch DVP clock driver to clk_hw interface
> - constify raspberrypi_clk_data in raspberrypi_clock_property
> - Don't mark firmware clocks as IGNORE_UNUSED
> - Change from reset_ms to reset_us in reset-simple, and add a bit more
> comments
> - Remove generic clk patch to test if a NULL pointer is returned
> - Removed misleading message in the is_prepared renaming patch commit
> message
> - Constify HDMI controller variants
> - Fix a bug in the allocation size of the clk data array
> - Added a mention in the DT binding conversion patches about the breakage
> - Merged a few fixes from kbuild
> - Fixed a few bisection and CEC build issues
> - Collected Acked-by and Reviewed-by
> - Change Dave email address to raspberrypi.com
>
> Dave Stevenson (7):
> drm/vc4: Add support for the BCM2711 HVS5
> drm/vc4: plane: Change LBM alignment constraint on LBM
> drm/vc4: plane: Optimize the LBM allocation size
> drm/vc4: hdmi: Use reg-names to retrieve the HDMI audio registers
> drm/vc4: hdmi: Reset audio infoframe on encoder_enable if previously streaming
> drm/vc4: hdmi: Set the b-frame marker to the match ALSA's default.
> drm/vc4: hdmi: Add audio-related callbacks
>
> Maxime Ripard (71):
> dt-bindings: display: Add support for the BCM2711 HVS
> drm/vc4: hvs: Boost the core clock during modeset
> drm/vc4: plane: Create more planes
> drm/vc4: crtc: Deal with different number of pixel per clock
> drm/vc4: crtc: Use a shared interrupt
> drm/vc4: crtc: Move the cob allocation outside of bind
> drm/vc4: crtc: Rename HVS channel to output
> drm/vc4: crtc: Use local chan variable
> drm/vc4: crtc: Enable and disable the PV in atomic_enable / disable
> drm/vc4: kms: Convert to for_each_new_crtc_state
> drm/vc4: crtc: Assign output to channel automatically
> drm/vc4: crtc: Add FIFO depth to vc4_crtc_data
> drm/vc4: crtc: Add function to compute FIFO level bits
> drm/vc4: crtc: Rename HDMI encoder type to HDMI0
> drm/vc4: crtc: Add HDMI1 encoder type
> drm/vc4: crtc: Disable color management for HVS5
> drm/vc4: crtc: Turn pixelvalve reset into a function
> drm/vc4: crtc: Move PV dump to config_pv
> drm/vc4: crtc: Move HVS init and close to a function
> drm/vc4: crtc: Move the HVS gamma LUT setup to our init function
> drm/vc4: hvs: Make sure our channel is reset
> drm/vc4: crtc: Remove mode_set_nofb
> drm/vc4: crtc: Remove redundant pixelvalve reset
> drm/vc4: crtc: Move HVS channel init before the PV initialisation
> drm/vc4: encoder: Add finer-grained encoder callbacks
> drm/vc4: crtc: Add a delay after disabling the PixelValve output
> drm/vc4: crtc: Clear the PixelValve FIFO on disable
> drm/vc4: crtc: Clear the PixelValve FIFO during configuration
> drm/vc4: hvs: Make the stop_channel function public
> drm/vc4: hvs: Introduce a function to get the assigned FIFO
> drm/vc4: crtc: Move the CRTC disable out
> drm/vc4: drv: Disable the CRTC at boot time
> dt-bindings: display: vc4: pv: Add BCM2711 pixel valves
> drm/vc4: crtc: Add BCM2711 pixelvalves
> drm/vc4: hdmi: Use debugfs private field
> drm/vc4: hdmi: Move structure to header
> drm/vc4: hdmi: rework connectors and encoders
> drm/vc4: hdmi: Remove DDC argument to connector_init
> drm/vc4: hdmi: Rename hdmi to vc4_hdmi
> drm/vc4: hdmi: Move accessors to vc4_hdmi
> drm/vc4: hdmi: Use local vc4_hdmi directly
> drm/vc4: hdmi: Add container_of macros for encoders and connectors
> drm/vc4: hdmi: Pass vc4_hdmi to CEC code
> drm/vc4: hdmi: Retrieve the vc4_hdmi at unbind using our device
> drm/vc4: hdmi: Remove vc4_dev hdmi pointer
> drm/vc4: hdmi: Remove vc4_hdmi_connector
> drm/vc4: hdmi: Introduce resource init and variant
> drm/vc4: hdmi: Implement a register layout abstraction
> drm/vc4: hdmi: Add reset callback
> drm/vc4: hdmi: Add PHY init and disable function
> drm/vc4: hdmi: Add PHY RNG enable / disable function
> drm/vc4: hdmi: Add a CSC setup callback
> drm/vc4: hdmi: Store the encoder type in the variant structure
> drm/vc4: hdmi: Deal with multiple debugfs files
> drm/vc4: hdmi: Move CEC init to its own function
> drm/vc4: hdmi: Add CEC support flag
> drm/vc4: hdmi: Remove unused CEC_CLOCK_DIV define
> drm/vc4: hdmi: Rename drm_encoder pointer in mode_valid
> drm/vc4: hdmi: Adjust HSM clock rate depending on pixel rate
> drm/vc4: hdmi: Use clk_set_min_rate instead
> drm/vc4: hdmi: Deal with multiple ALSA cards
> drm/vc4: hdmi: Remove register dumps in enable
> drm/vc4: hdmi: Always recenter the HDMI FIFO
> drm/vc4: hdmi: Implement finer-grained hooks
> drm/vc4: hdmi: Do the VID_CTL configuration at once
> drm/vc4: hdmi: Switch to blank pixels when disabled
> drm/vc4: hdmi: Support the BCM2711 HDMI controllers
> dt-bindings: display: vc4: hdmi: Add BCM2711 HDMI controllers bindings
> dt-bindings: display: vc4: Document BCM2711 VC5
> drm/vc4: drv: Support BCM2711
> ARM: dts: bcm2711: Enable the display pipeline
>
> Documentation/devicetree/bindings/display/brcm,bcm2711-hdmi.yaml | 109 +++++-
> Documentation/devicetree/bindings/display/brcm,bcm2835-hvs.yaml | 18 +-
> Documentation/devicetree/bindings/display/brcm,bcm2835-pixelvalve0.yaml | 5 +-
> Documentation/devicetree/bindings/display/brcm,bcm2835-vc4.yaml | 1 +-
> arch/arm/boot/dts/bcm2711-rpi-4-b.dts | 46 ++-
> arch/arm/boot/dts/bcm2711.dtsi | 115 ++++-
> drivers/gpu/drm/vc4/Makefile | 1 +-
> drivers/gpu/drm/vc4/vc4_crtc.c | 338 +++++++++++----
> drivers/gpu/drm/vc4/vc4_drv.c | 5 +-
> drivers/gpu/drm/vc4/vc4_drv.h | 43 +-
> drivers/gpu/drm/vc4/vc4_hdmi.c | 1625 +++++++++++++++++++++++++++++++++++++++++++-----------------------------
> drivers/gpu/drm/vc4/vc4_hdmi.h | 183 ++++++++-
> drivers/gpu/drm/vc4/vc4_hdmi_phy.c | 520 +++++++++++++++++++++++-
> drivers/gpu/drm/vc4/vc4_hdmi_regs.h | 442 ++++++++++++++++++++-
> drivers/gpu/drm/vc4/vc4_hvs.c | 260 +++++++-----
> drivers/gpu/drm/vc4/vc4_kms.c | 225 +++++++++-
> drivers/gpu/drm/vc4/vc4_plane.c | 222 +++++++---
> drivers/gpu/drm/vc4/vc4_regs.h | 177 +++-----
> drivers/gpu/drm/vc4/vc4_txp.c | 4 +-
> 19 files changed, 3331 insertions(+), 1008 deletions(-)
> create mode 100644 Documentation/devicetree/bindings/display/brcm,bcm2711-hdmi.yaml
> create mode 100644 drivers/gpu/drm/vc4/vc4_hdmi.h
> create mode 100644 drivers/gpu/drm/vc4/vc4_hdmi_phy.c
> create mode 100644 drivers/gpu/drm/vc4/vc4_hdmi_regs.h
>
> base-commit: 5bdd2824d705fb8d339d6f96e464b907c9a1553d
^ permalink raw reply [flat|nested] 7+ messages in thread
* Re: [PATCH v4 00/78] drm/vc4: Support BCM2711 Display Pipeline
2020-07-08 17:41 ` [PATCH v4 00/78] drm/vc4: Support BCM2711 Display Pipeline Maxime Ripard
` (2 preceding siblings ...)
2020-08-21 7:18 ` Hoegeun Kwon
@ 2020-08-31 2:36 ` Chanwoo Choi
3 siblings, 0 replies; 7+ messages in thread
From: Chanwoo Choi @ 2020-08-31 2:36 UTC (permalink / raw)
To: Maxime Ripard, Nicolas Saenz Julienne, Eric Anholt
Cc: dri-devel, linux-rpi-kernel, bcm-kernel-feedback-list,
linux-arm-kernel, linux-kernel, Dave Stevenson, Tim Gover,
Phil Elwell, devicetree, Kamal Dasu, linux-clk,
Michael Turquette, Philipp Zabel, Rob Herring, Stephen Boyd
Hi Maxime,
On 7/9/20 2:41 AM, Maxime Ripard wrote:
> Hi everyone,
>
> Here's a (pretty long) series to introduce support in the VC4 DRM driver
> for the display pipeline found in the BCM2711 (and thus the RaspberryPi 4).
>
> The main differences are that there's two HDMI controllers and that there's
> more pixelvalve now. Those pixelvalve come with a mux in the HVS that still
> have only 3 FIFOs. Both of those differences are breaking a bunch of
> expectations in the driver, so we first need a good bunch of cleanup and
> reworks to introduce support for the new controllers.
>
> Similarly, the HDMI controller has all its registers shuffled and split in
> multiple controllers now, so we need a bunch of changes to support this as
> well.
>
> Only the HDMI support is enabled for now (even though the DPI and DSI
> outputs have been tested too).
>
> Let me know if you have any comments
> Maxime
>
> Cc: bcm-kernel-feedback-list@broadcom.com
> Cc: devicetree@vger.kernel.org
> Cc: Kamal Dasu <kdasu.kdev@gmail.com>
> Cc: linux-clk@vger.kernel.org
> Cc: Michael Turquette <mturquette@baylibre.com>
> Cc: Philipp Zabel <p.zabel@pengutronix.de>
> Cc: Rob Herring <robh+dt@kernel.org>
> Cc: Stephen Boyd <sboyd@kernel.org>
>
> Changes from v3:
> - Rebased on top of next-20200708
> - Added a name to the HDMI audio codec component
> - Only disable the BCM2711 HDMI pixelvalves at boot
> - Fixed an error in the HVS binding
> - Fix a framebuffer size condition that was inverted
> - Changed the channel allocation algorithm using Eric's suggestion
> - Always write the muxing values instead of updating if needed
> - Improved a bit the hvs_available_channels comment in the structure
> - Change atomic_complete_commit code to use for_each_new_crtc_in_state
> - Change the muxing code to take into account disparities between the
> BCM2711 and previous SoCs.
> - Only change the clock rate on BCM2711 during a modeset
> - Fix a crash at atomic_disable
> - Use clk_set_min_rate for the core clock too
> - Add a few defines, and simplify the FIFO level stuff
> - Reordered the patches according to Eric's reviews
> - Fixed a regression with VID_CTL setting on RPI3
>
> Changes from v2:
> - Rebased on top of next-20200526
> - Split the firmware clock series away
> - Removed the stuck pixel (with all the subsequent pixels being shifted
> by one
> - Fixed the writeback issue too.
> - Fix the dual output
> - Fixed the return value of phy_get_cp_current
> - Enhanced the comment on the reset delay
> - Increase the max width and height
> - Made a proper Kconfig option for the DVP clock driver
> - Fixed the alsa card name collision
>
> Changes from v1:
> - Rebased on top of 5.7-rc1
> - Run checkpatch
> - Added audio support
> - Fixed some HDMI timeouts
> - Swiched to clk_hw_register_gate_parent_data
> - Reorder Kconfig symbols in drivers/i2c/busses
> - Make the firmware clocks a child of the firmware node
> - Switch DVP clock driver to clk_hw interface
> - constify raspberrypi_clk_data in raspberrypi_clock_property
> - Don't mark firmware clocks as IGNORE_UNUSED
> - Change from reset_ms to reset_us in reset-simple, and add a bit more
> comments
> - Remove generic clk patch to test if a NULL pointer is returned
> - Removed misleading message in the is_prepared renaming patch commit
> message
> - Constify HDMI controller variants
> - Fix a bug in the allocation size of the clk data array
> - Added a mention in the DT binding conversion patches about the breakage
> - Merged a few fixes from kbuild
> - Fixed a few bisection and CEC build issues
> - Collected Acked-by and Reviewed-by
> - Change Dave email address to raspberrypi.com
>
> Dave Stevenson (7):
> drm/vc4: Add support for the BCM2711 HVS5
> drm/vc4: plane: Change LBM alignment constraint on LBM
> drm/vc4: plane: Optimize the LBM allocation size
> drm/vc4: hdmi: Use reg-names to retrieve the HDMI audio registers
> drm/vc4: hdmi: Reset audio infoframe on encoder_enable if previously streaming
> drm/vc4: hdmi: Set the b-frame marker to the match ALSA's default.
> drm/vc4: hdmi: Add audio-related callbacks
>
> Maxime Ripard (71):
> dt-bindings: display: Add support for the BCM2711 HVS
> drm/vc4: hvs: Boost the core clock during modeset
> drm/vc4: plane: Create more planes
> drm/vc4: crtc: Deal with different number of pixel per clock
> drm/vc4: crtc: Use a shared interrupt
> drm/vc4: crtc: Move the cob allocation outside of bind
> drm/vc4: crtc: Rename HVS channel to output
> drm/vc4: crtc: Use local chan variable
> drm/vc4: crtc: Enable and disable the PV in atomic_enable / disable
> drm/vc4: kms: Convert to for_each_new_crtc_state
> drm/vc4: crtc: Assign output to channel automatically
> drm/vc4: crtc: Add FIFO depth to vc4_crtc_data
> drm/vc4: crtc: Add function to compute FIFO level bits
> drm/vc4: crtc: Rename HDMI encoder type to HDMI0
> drm/vc4: crtc: Add HDMI1 encoder type
> drm/vc4: crtc: Disable color management for HVS5
> drm/vc4: crtc: Turn pixelvalve reset into a function
> drm/vc4: crtc: Move PV dump to config_pv
> drm/vc4: crtc: Move HVS init and close to a function
> drm/vc4: crtc: Move the HVS gamma LUT setup to our init function
> drm/vc4: hvs: Make sure our channel is reset
> drm/vc4: crtc: Remove mode_set_nofb
> drm/vc4: crtc: Remove redundant pixelvalve reset
> drm/vc4: crtc: Move HVS channel init before the PV initialisation
> drm/vc4: encoder: Add finer-grained encoder callbacks
> drm/vc4: crtc: Add a delay after disabling the PixelValve output
> drm/vc4: crtc: Clear the PixelValve FIFO on disable
> drm/vc4: crtc: Clear the PixelValve FIFO during configuration
> drm/vc4: hvs: Make the stop_channel function public
> drm/vc4: hvs: Introduce a function to get the assigned FIFO
> drm/vc4: crtc: Move the CRTC disable out
> drm/vc4: drv: Disable the CRTC at boot time
> dt-bindings: display: vc4: pv: Add BCM2711 pixel valves
> drm/vc4: crtc: Add BCM2711 pixelvalves
> drm/vc4: hdmi: Use debugfs private field
> drm/vc4: hdmi: Move structure to header
> drm/vc4: hdmi: rework connectors and encoders
> drm/vc4: hdmi: Remove DDC argument to connector_init
> drm/vc4: hdmi: Rename hdmi to vc4_hdmi
> drm/vc4: hdmi: Move accessors to vc4_hdmi
> drm/vc4: hdmi: Use local vc4_hdmi directly
> drm/vc4: hdmi: Add container_of macros for encoders and connectors
> drm/vc4: hdmi: Pass vc4_hdmi to CEC code
> drm/vc4: hdmi: Retrieve the vc4_hdmi at unbind using our device
> drm/vc4: hdmi: Remove vc4_dev hdmi pointer
> drm/vc4: hdmi: Remove vc4_hdmi_connector
> drm/vc4: hdmi: Introduce resource init and variant
> drm/vc4: hdmi: Implement a register layout abstraction
> drm/vc4: hdmi: Add reset callback
> drm/vc4: hdmi: Add PHY init and disable function
> drm/vc4: hdmi: Add PHY RNG enable / disable function
> drm/vc4: hdmi: Add a CSC setup callback
> drm/vc4: hdmi: Store the encoder type in the variant structure
> drm/vc4: hdmi: Deal with multiple debugfs files
> drm/vc4: hdmi: Move CEC init to its own function
> drm/vc4: hdmi: Add CEC support flag
> drm/vc4: hdmi: Remove unused CEC_CLOCK_DIV define
> drm/vc4: hdmi: Rename drm_encoder pointer in mode_valid
> drm/vc4: hdmi: Adjust HSM clock rate depending on pixel rate
> drm/vc4: hdmi: Use clk_set_min_rate instead
> drm/vc4: hdmi: Deal with multiple ALSA cards
> drm/vc4: hdmi: Remove register dumps in enable
> drm/vc4: hdmi: Always recenter the HDMI FIFO
> drm/vc4: hdmi: Implement finer-grained hooks
> drm/vc4: hdmi: Do the VID_CTL configuration at once
> drm/vc4: hdmi: Switch to blank pixels when disabled
> drm/vc4: hdmi: Support the BCM2711 HDMI controllers
> dt-bindings: display: vc4: hdmi: Add BCM2711 HDMI controllers bindings
> dt-bindings: display: vc4: Document BCM2711 VC5
> drm/vc4: drv: Support BCM2711
> ARM: dts: bcm2711: Enable the display pipeline
>
> Documentation/devicetree/bindings/display/brcm,bcm2711-hdmi.yaml | 109 +++++-
> Documentation/devicetree/bindings/display/brcm,bcm2835-hvs.yaml | 18 +-
> Documentation/devicetree/bindings/display/brcm,bcm2835-pixelvalve0.yaml | 5 +-
> Documentation/devicetree/bindings/display/brcm,bcm2835-vc4.yaml | 1 +-
> arch/arm/boot/dts/bcm2711-rpi-4-b.dts | 46 ++-
> arch/arm/boot/dts/bcm2711.dtsi | 115 ++++-
> drivers/gpu/drm/vc4/Makefile | 1 +-
> drivers/gpu/drm/vc4/vc4_crtc.c | 338 +++++++++++----
> drivers/gpu/drm/vc4/vc4_drv.c | 5 +-
> drivers/gpu/drm/vc4/vc4_drv.h | 43 +-
> drivers/gpu/drm/vc4/vc4_hdmi.c | 1625 +++++++++++++++++++++++++++++++++++++++++++-----------------------------
> drivers/gpu/drm/vc4/vc4_hdmi.h | 183 ++++++++-
> drivers/gpu/drm/vc4/vc4_hdmi_phy.c | 520 +++++++++++++++++++++++-
> drivers/gpu/drm/vc4/vc4_hdmi_regs.h | 442 ++++++++++++++++++++-
> drivers/gpu/drm/vc4/vc4_hvs.c | 260 +++++++-----
> drivers/gpu/drm/vc4/vc4_kms.c | 225 +++++++++-
> drivers/gpu/drm/vc4/vc4_plane.c | 222 +++++++---
> drivers/gpu/drm/vc4/vc4_regs.h | 177 +++-----
> drivers/gpu/drm/vc4/vc4_txp.c | 4 +-
> 19 files changed, 3331 insertions(+), 1008 deletions(-)
> create mode 100644 Documentation/devicetree/bindings/display/brcm,bcm2711-hdmi.yaml
> create mode 100644 drivers/gpu/drm/vc4/vc4_hdmi.h
> create mode 100644 drivers/gpu/drm/vc4/vc4_hdmi_phy.c
> create mode 100644 drivers/gpu/drm/vc4/vc4_hdmi_regs.h
>
> base-commit: 5bdd2824d705fb8d339d6f96e464b907c9a1553d
>
I tested it for stress test with reboot command repetitively
for verifying this patchset. It is well working.
Tested-by: Chanwoo Choi <cw00.choi@samsung.com>
--
Best Regards,
Chanwoo Choi
Samsung Electronics
^ permalink raw reply [flat|nested] 7+ messages in thread
* Re: [PATCH v4 00/78] drm/vc4: Support BCM2711 Display Pipeline
2020-08-21 7:18 ` Hoegeun Kwon
@ 2020-09-02 13:32 ` Maxime Ripard
2020-09-02 13:52 ` Maxime Ripard
0 siblings, 1 reply; 7+ messages in thread
From: Maxime Ripard @ 2020-09-02 13:32 UTC (permalink / raw)
To: Hoegeun Kwon
Cc: Nicolas Saenz Julienne, Eric Anholt, devicetree, Tim Gover,
Dave Stevenson, Stephen Boyd, Michael Turquette, Kamal Dasu,
linux-kernel, dri-devel, linux-clk, Rob Herring,
bcm-kernel-feedback-list, linux-rpi-kernel, Phil Elwell,
linux-arm-kernel
[-- Attachment #1: Type: text/plain, Size: 934 bytes --]
Hi Hoegeun
On Fri, Aug 21, 2020 at 04:18:34PM +0900, Hoegeun Kwon wrote:
> Hi Maxime,
>
> Thank you for your version 4 patch.
> I tested all 78 patches based on the next-20200708.
>
>
> Dual HDMI opearation does not work normally.
> flip_done timed out occurs and doesn't work.
> Could you check please it.
>
> [ 105.694541] [drm:drm_atomic_helper_wait_for_dependencies] *ERROR*
> [CRTC:64:crtc-3] flip_done timed out
> [ 115.934994] [drm:drm_atomic_helper_wait_for_dependencies] *ERROR*
> [CONNECTOR:32:HDMI-A-1] flip_done timed out
> [ 126.174545] [drm:drm_atomic_helper_wait_for_dependencies] *ERROR*
> [PLANE:60:plane-3] flip_done timed out
Thanks for testing and reporting this. I've been looking into it, and it
seems that it's not just the dual output that's broken, but HDMI1
entirely (so even a single display connected to HDMI1 doesn't work).
Is it happening for you as well?
Maxime
[-- Attachment #2: signature.asc --]
[-- Type: application/pgp-signature, Size: 228 bytes --]
^ permalink raw reply [flat|nested] 7+ messages in thread
* Re: [PATCH v4 00/78] drm/vc4: Support BCM2711 Display Pipeline
2020-09-02 13:32 ` Maxime Ripard
@ 2020-09-02 13:52 ` Maxime Ripard
0 siblings, 0 replies; 7+ messages in thread
From: Maxime Ripard @ 2020-09-02 13:52 UTC (permalink / raw)
To: Hoegeun Kwon
Cc: Nicolas Saenz Julienne, Eric Anholt, devicetree, Tim Gover,
Dave Stevenson, Stephen Boyd, Michael Turquette, Kamal Dasu,
linux-kernel, dri-devel, linux-clk, Rob Herring,
bcm-kernel-feedback-list, linux-rpi-kernel, Phil Elwell,
linux-arm-kernel
[-- Attachment #1: Type: text/plain, Size: 1117 bytes --]
On Wed, Sep 02, 2020 at 03:32:20PM +0200, Maxime Ripard wrote:
> Hi Hoegeun
>
> On Fri, Aug 21, 2020 at 04:18:34PM +0900, Hoegeun Kwon wrote:
> > Hi Maxime,
> >
> > Thank you for your version 4 patch.
> > I tested all 78 patches based on the next-20200708.
> >
> >
> > Dual HDMI opearation does not work normally.
> > flip_done timed out occurs and doesn't work.
> > Could you check please it.
> >
> > [ 105.694541] [drm:drm_atomic_helper_wait_for_dependencies] *ERROR*
> > [CRTC:64:crtc-3] flip_done timed out
> > [ 115.934994] [drm:drm_atomic_helper_wait_for_dependencies] *ERROR*
> > [CONNECTOR:32:HDMI-A-1] flip_done timed out
> > [ 126.174545] [drm:drm_atomic_helper_wait_for_dependencies] *ERROR*
> > [PLANE:60:plane-3] flip_done timed out
>
> Thanks for testing and reporting this. I've been looking into it, and it
> seems that it's not just the dual output that's broken, but HDMI1
> entirely (so even a single display connected to HDMI1 doesn't work).
>
> Is it happening for you as well?
Nevermind, I had the DSI panel connected and it was interfering
Maxime
[-- Attachment #2: signature.asc --]
[-- Type: application/pgp-signature, Size: 228 bytes --]
^ permalink raw reply [flat|nested] 7+ messages in thread
end of thread, other threads:[~2020-09-02 14:59 UTC | newest]
Thread overview: 7+ messages (download: mbox.gz / follow: Atom feed)
-- links below jump to the message on this page --
[not found] <CGME20200709070649epcas1p13664bacc66a0f73443bf4d3e8940f933@epcas1p1.samsung.com>
2020-07-08 17:41 ` [PATCH v4 00/78] drm/vc4: Support BCM2711 Display Pipeline Maxime Ripard
2020-07-10 7:37 ` Jian-Hong Pan
2020-07-10 9:58 ` Stefan Wahren
2020-08-21 7:18 ` Hoegeun Kwon
2020-09-02 13:32 ` Maxime Ripard
2020-09-02 13:52 ` Maxime Ripard
2020-08-31 2:36 ` Chanwoo Choi
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).