* [PATCH] DTS: bcm2711: Move emmc2 into its own bus
@ 2020-03-03 12:08 Nicolas Saenz Julienne
2020-03-03 18:21 ` Florian Fainelli
0 siblings, 1 reply; 3+ messages in thread
From: Nicolas Saenz Julienne @ 2020-03-03 12:08 UTC (permalink / raw)
To: Rob Herring, Nicolas Saenz Julienne
Cc: phil, florian.fainelli, devicetree, bcm-kernel-feedback-list,
linux-rpi-kernel, linux-arm-kernel, linux-kernel
Depending on bcm2711's revision its emmc2 controller might have
different DMA constraints. Raspberry Pi 4's firmware will take care of
updating those, but only if a certain alias is found in the device tree.
So, move emmc2 into its own bus, so as not to pollute other devices with
dma-ranges changes and create the emmc2bus alias.
Based in Phil ELwell's downstream implementation.
Signed-off-by: Nicolas Saenz Julienne <nsaenzjulienne@suse.de>
---
arch/arm/boot/dts/bcm2711-rpi-4-b.dts | 1 +
arch/arm/boot/dts/bcm2711.dtsi | 19 ++++++++++++++-----
2 files changed, 15 insertions(+), 5 deletions(-)
diff --git a/arch/arm/boot/dts/bcm2711-rpi-4-b.dts b/arch/arm/boot/dts/bcm2711-rpi-4-b.dts
index 1d4b589fe233..e26ea9006378 100644
--- a/arch/arm/boot/dts/bcm2711-rpi-4-b.dts
+++ b/arch/arm/boot/dts/bcm2711-rpi-4-b.dts
@@ -20,6 +20,7 @@ memory@0 {
};
aliases {
+ emmc2bus = &emmc2bus;
ethernet0 = &genet;
pcie0 = &pcie0;
};
diff --git a/arch/arm/boot/dts/bcm2711.dtsi b/arch/arm/boot/dts/bcm2711.dtsi
index d1e684d0acfd..61ea8b44c51e 100644
--- a/arch/arm/boot/dts/bcm2711.dtsi
+++ b/arch/arm/boot/dts/bcm2711.dtsi
@@ -241,17 +241,26 @@ pwm1: pwm@7e20c800 {
status = "disabled";
};
+ hvs@7e400000 {
+ interrupts = <GIC_SPI 97 IRQ_TYPE_LEVEL_HIGH>;
+ };
+ };
+
+ emmc2bus: emmc2bus {
+ compatible = "simple-bus";
+ #address-cells = <2>;
+ #size-cells = <1>;
+
+ ranges = <0x0 0x7e000000 0x0 0xfe000000 0x01800000>;
+ dma-ranges = <0x0 0xc0000000 0x0 0x00000000 0x40000000>;
+
emmc2: emmc2@7e340000 {
compatible = "brcm,bcm2711-emmc2";
- reg = <0x7e340000 0x100>;
+ reg = <0x0 0x7e340000 0x100>;
interrupts = <GIC_SPI 126 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&clocks BCM2711_CLOCK_EMMC2>;
status = "disabled";
};
-
- hvs@7e400000 {
- interrupts = <GIC_SPI 97 IRQ_TYPE_LEVEL_HIGH>;
- };
};
arm-pmu {
--
2.25.1
^ permalink raw reply related [flat|nested] 3+ messages in thread
* Re: [PATCH] DTS: bcm2711: Move emmc2 into its own bus
2020-03-03 12:08 [PATCH] DTS: bcm2711: Move emmc2 into its own bus Nicolas Saenz Julienne
@ 2020-03-03 18:21 ` Florian Fainelli
2020-03-03 18:32 ` Nicolas Saenz Julienne
0 siblings, 1 reply; 3+ messages in thread
From: Florian Fainelli @ 2020-03-03 18:21 UTC (permalink / raw)
To: Nicolas Saenz Julienne, Rob Herring
Cc: devicetree, florian.fainelli, phil, linux-kernel,
bcm-kernel-feedback-list, linux-rpi-kernel, linux-arm-kernel
On 3/3/20 4:08 AM, Nicolas Saenz Julienne wrote:
> Depending on bcm2711's revision its emmc2 controller might have
> different DMA constraints. Raspberry Pi 4's firmware will take care of
> updating those, but only if a certain alias is found in the device tree.
> So, move emmc2 into its own bus, so as not to pollute other devices with
> dma-ranges changes and create the emmc2bus alias.
>
> Based in Phil ELwell's downstream implementation.
>
> Signed-off-by: Nicolas Saenz Julienne <nsaenzjulienne@suse.de>
Nit: the subject should be ARM: dts: bcm2711. Some more comments below.
> ---
> arch/arm/boot/dts/bcm2711-rpi-4-b.dts | 1 +
> arch/arm/boot/dts/bcm2711.dtsi | 19 ++++++++++++++-----
> 2 files changed, 15 insertions(+), 5 deletions(-)
>
> diff --git a/arch/arm/boot/dts/bcm2711-rpi-4-b.dts b/arch/arm/boot/dts/bcm2711-rpi-4-b.dts
> index 1d4b589fe233..e26ea9006378 100644
> --- a/arch/arm/boot/dts/bcm2711-rpi-4-b.dts
> +++ b/arch/arm/boot/dts/bcm2711-rpi-4-b.dts
> @@ -20,6 +20,7 @@ memory@0 {
> };
>
> aliases {
> + emmc2bus = &emmc2bus;
> ethernet0 = &genet;
> pcie0 = &pcie0;
> };
> diff --git a/arch/arm/boot/dts/bcm2711.dtsi b/arch/arm/boot/dts/bcm2711.dtsi
> index d1e684d0acfd..61ea8b44c51e 100644
> --- a/arch/arm/boot/dts/bcm2711.dtsi
> +++ b/arch/arm/boot/dts/bcm2711.dtsi
> @@ -241,17 +241,26 @@ pwm1: pwm@7e20c800 {
> status = "disabled";
> };
>
> + hvs@7e400000 {
> + interrupts = <GIC_SPI 97 IRQ_TYPE_LEVEL_HIGH>;
> + };
> + };
> +
> + emmc2bus: emmc2bus {
> + compatible = "simple-bus";
> + #address-cells = <2>;
> + #size-cells = <1>;
> +
> + ranges = <0x0 0x7e000000 0x0 0xfe000000 0x01800000>;
> + dma-ranges = <0x0 0xc0000000 0x0 0x00000000 0x40000000>;
This deserves a comment for two reasons:
- explaining which of these properties is getting patched by the
firmware (and it would be really nice if we had a concept of annotation
attributes for Device Tree such that you could express something like:
dma-ranges = <> __patchable;
- explaining why this is not collapsed in the soc bus node, because the
dma-ranges constraint can be different based on the Pi4 revision
With that fixed, this looks good to me!
> +
> emmc2: emmc2@7e340000 {
> compatible = "brcm,bcm2711-emmc2";
> - reg = <0x7e340000 0x100>;
> + reg = <0x0 0x7e340000 0x100>;
> interrupts = <GIC_SPI 126 IRQ_TYPE_LEVEL_HIGH>;
> clocks = <&clocks BCM2711_CLOCK_EMMC2>;
> status = "disabled";
> };
> -
> - hvs@7e400000 {
> - interrupts = <GIC_SPI 97 IRQ_TYPE_LEVEL_HIGH>;
> - };
> };
>
> arm-pmu {
>
--
Florian
^ permalink raw reply [flat|nested] 3+ messages in thread
* Re: [PATCH] DTS: bcm2711: Move emmc2 into its own bus
2020-03-03 18:21 ` Florian Fainelli
@ 2020-03-03 18:32 ` Nicolas Saenz Julienne
0 siblings, 0 replies; 3+ messages in thread
From: Nicolas Saenz Julienne @ 2020-03-03 18:32 UTC (permalink / raw)
To: Florian Fainelli, Rob Herring
Cc: devicetree, florian.fainelli, phil, linux-kernel,
bcm-kernel-feedback-list, linux-rpi-kernel, linux-arm-kernel
[-- Attachment #1: Type: text/plain, Size: 3201 bytes --]
Hi Florian,
On Tue, 2020-03-03 at 10:21 -0800, Florian Fainelli wrote:
> On 3/3/20 4:08 AM, Nicolas Saenz Julienne wrote:
> > Depending on bcm2711's revision its emmc2 controller might have
> > different DMA constraints. Raspberry Pi 4's firmware will take care of
> > updating those, but only if a certain alias is found in the device tree.
> > So, move emmc2 into its own bus, so as not to pollute other devices with
> > dma-ranges changes and create the emmc2bus alias.
> >
> > Based in Phil ELwell's downstream implementation.
> >
> > Signed-off-by: Nicolas Saenz Julienne <nsaenzjulienne@suse.de>
>
> Nit: the subject should be ARM: dts: bcm2711. Some more comments below.
Of course, should have known better.
> > ---
> > arch/arm/boot/dts/bcm2711-rpi-4-b.dts | 1 +
> > arch/arm/boot/dts/bcm2711.dtsi | 19 ++++++++++++++-----
> > 2 files changed, 15 insertions(+), 5 deletions(-)
> >
> > diff --git a/arch/arm/boot/dts/bcm2711-rpi-4-b.dts
> > b/arch/arm/boot/dts/bcm2711-rpi-4-b.dts
> > index 1d4b589fe233..e26ea9006378 100644
> > --- a/arch/arm/boot/dts/bcm2711-rpi-4-b.dts
> > +++ b/arch/arm/boot/dts/bcm2711-rpi-4-b.dts
> > @@ -20,6 +20,7 @@ memory@0 {
> > };
> >
> > aliases {
> > + emmc2bus = &emmc2bus;
> > ethernet0 = &genet;
> > pcie0 = &pcie0;
> > };
> > diff --git a/arch/arm/boot/dts/bcm2711.dtsi b/arch/arm/boot/dts/bcm2711.dtsi
> > index d1e684d0acfd..61ea8b44c51e 100644
> > --- a/arch/arm/boot/dts/bcm2711.dtsi
> > +++ b/arch/arm/boot/dts/bcm2711.dtsi
> > @@ -241,17 +241,26 @@ pwm1: pwm@7e20c800 {
> > status = "disabled";
> > };
> >
> > + hvs@7e400000 {
> > + interrupts = <GIC_SPI 97 IRQ_TYPE_LEVEL_HIGH>;
> > + };
> > + };
> > +
> > + emmc2bus: emmc2bus {
> > + compatible = "simple-bus";
> > + #address-cells = <2>;
> > + #size-cells = <1>;
> > +
> > + ranges = <0x0 0x7e000000 0x0 0xfe000000 0x01800000>;
> > + dma-ranges = <0x0 0xc0000000 0x0 0x00000000 0x40000000>;
>
> This deserves a comment for two reasons:
>
> - explaining which of these properties is getting patched by the
> firmware (and it would be really nice if we had a concept of annotation
> attributes for Device Tree such that you could express something like:
>
> dma-ranges = <> __patchable;
Something like this would've been useful to me some time ago while debugging
CMA issues on a random arm64 Board. I was left wondering if the memory nodes on
that specific board were set in stone or just a placeholder.
> - explaining why this is not collapsed in the soc bus node, because the
> dma-ranges constraint can be different based on the Pi4 revision
Noted
> With that fixed, this looks good to me!
Thanks!
>
> > +
> > emmc2: emmc2@7e340000 {
> > compatible = "brcm,bcm2711-emmc2";
> > - reg = <0x7e340000 0x100>;
> > + reg = <0x0 0x7e340000 0x100>;
> > interrupts = <GIC_SPI 126 IRQ_TYPE_LEVEL_HIGH>;
> > clocks = <&clocks BCM2711_CLOCK_EMMC2>;
> > status = "disabled";
> > };
> > -
> > - hvs@7e400000 {
> > - interrupts = <GIC_SPI 97 IRQ_TYPE_LEVEL_HIGH>;
> > - };
> > };
> >
> > arm-pmu {
> >
>
>
[-- Attachment #2: This is a digitally signed message part --]
[-- Type: application/pgp-signature, Size: 488 bytes --]
^ permalink raw reply [flat|nested] 3+ messages in thread
end of thread, other threads:[~2020-03-03 18:32 UTC | newest]
Thread overview: 3+ messages (download: mbox.gz / follow: Atom feed)
-- links below jump to the message on this page --
2020-03-03 12:08 [PATCH] DTS: bcm2711: Move emmc2 into its own bus Nicolas Saenz Julienne
2020-03-03 18:21 ` Florian Fainelli
2020-03-03 18:32 ` Nicolas Saenz Julienne
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).