* [PATCH V3 1/2] backlight: qcom-wled: Fix FSC update issue for WLED5 [not found] <1614590916-27070-1-git-send-email-kgunda@codeaurora.org> @ 2021-03-01 9:28 ` Kiran Gunda 2021-03-01 9:28 ` [PATCH V3 2/2] backlight: qcom-wled: Correct the sync_toggle sequence Kiran Gunda 1 sibling, 0 replies; 4+ messages in thread From: Kiran Gunda @ 2021-03-01 9:28 UTC (permalink / raw) To: bjorn.andersson, jingoohan1, lee.jones, b.zolnierkie, dri-devel, daniel.thompson, jacek.anaszewski, pavel, robh+dt, mark.rutland, linux-leds, devicetree, linux-kernel, Andy Gross, linux-arm-msm, linux-fbdev Cc: phone-devel, Kiran Gunda Currently, for WLED5, the FSC (Full scale current) setting is not updated properly due to driver toggling the wrong register after an FSC update. On WLED5 we should only toggle the MOD_SYNC bit after a brightness update. For an FSC update we need to toggle the SYNC bits instead. Fix it by adopting the common wled3_sync_toggle() for WLED5 and introducing new code to the brightness update path to compensate. Signed-off-by: Kiran Gunda <kgunda@codeaurora.org> Reviewed-by: Daniel Thompson <daniel.thompson@linaro.org> --- drivers/video/backlight/qcom-wled.c | 25 +++++++++++++++++++------ 1 file changed, 19 insertions(+), 6 deletions(-) diff --git a/drivers/video/backlight/qcom-wled.c b/drivers/video/backlight/qcom-wled.c index 3bc7800..aef52b9 100644 --- a/drivers/video/backlight/qcom-wled.c +++ b/drivers/video/backlight/qcom-wled.c @@ -348,7 +348,7 @@ static int wled3_sync_toggle(struct wled *wled) return rc; } -static int wled5_sync_toggle(struct wled *wled) +static int wled5_mod_sync_toggle(struct wled *wled) { int rc; u8 val; @@ -445,10 +445,23 @@ static int wled_update_status(struct backlight_device *bl) goto unlock_mutex; } - rc = wled->wled_sync_toggle(wled); - if (rc < 0) { - dev_err(wled->dev, "wled sync failed rc:%d\n", rc); - goto unlock_mutex; + if (wled->version < 5) { + rc = wled->wled_sync_toggle(wled); + if (rc < 0) { + dev_err(wled->dev, "wled sync failed rc:%d\n", rc); + goto unlock_mutex; + } + } else { + /* + * For WLED5 toggling the MOD_SYNC_BIT updates the + * brightness + */ + rc = wled5_mod_sync_toggle(wled); + if (rc < 0) { + dev_err(wled->dev, "wled mod sync failed rc:%d\n", + rc); + goto unlock_mutex; + } } } @@ -1459,7 +1472,7 @@ static int wled_configure(struct wled *wled) size = ARRAY_SIZE(wled5_opts); *cfg = wled5_config_defaults; wled->wled_set_brightness = wled5_set_brightness; - wled->wled_sync_toggle = wled5_sync_toggle; + wled->wled_sync_toggle = wled3_sync_toggle; wled->wled_cabc_config = wled5_cabc_config; wled->wled_ovp_delay = wled5_ovp_delay; wled->wled_auto_detection_required = -- The Qualcomm Innovation Center, Inc. is a member of the Code Aurora Forum, a Linux Foundation Collaborative Project ^ permalink raw reply related [flat|nested] 4+ messages in thread
* [PATCH V3 2/2] backlight: qcom-wled: Correct the sync_toggle sequence [not found] <1614590916-27070-1-git-send-email-kgunda@codeaurora.org> 2021-03-01 9:28 ` [PATCH V3 1/2] backlight: qcom-wled: Fix FSC update issue for WLED5 Kiran Gunda @ 2021-03-01 9:28 ` Kiran Gunda 2021-03-01 10:02 ` Daniel Thompson 1 sibling, 1 reply; 4+ messages in thread From: Kiran Gunda @ 2021-03-01 9:28 UTC (permalink / raw) To: bjorn.andersson, jingoohan1, lee.jones, b.zolnierkie, dri-devel, daniel.thompson, jacek.anaszewski, pavel, robh+dt, mark.rutland, linux-leds, devicetree, linux-kernel, Andy Gross, linux-arm-msm, linux-fbdev Cc: phone-devel, Kiran Gunda As per the current implementation, after FSC (Full Scale Current) and brightness update the sync bits are transitioned from set-then-clear. But, the FSC and brightness sync takes place during a clear-then-set transition of the sync bits. So the hardware team recommends a clear-then-set approach in order to guarantee such a transition regardless of the previous register state. Signed-off-by: Kiran Gunda <kgunda@codeaurora.org> --- drivers/video/backlight/qcom-wled.c | 12 ++++++------ 1 file changed, 6 insertions(+), 6 deletions(-) diff --git a/drivers/video/backlight/qcom-wled.c b/drivers/video/backlight/qcom-wled.c index aef52b9..19f83ac 100644 --- a/drivers/video/backlight/qcom-wled.c +++ b/drivers/video/backlight/qcom-wled.c @@ -337,13 +337,13 @@ static int wled3_sync_toggle(struct wled *wled) rc = regmap_update_bits(wled->regmap, wled->ctrl_addr + WLED3_SINK_REG_SYNC, - mask, mask); + mask, WLED3_SINK_REG_SYNC_CLEAR); if (rc < 0) return rc; rc = regmap_update_bits(wled->regmap, wled->ctrl_addr + WLED3_SINK_REG_SYNC, - mask, WLED3_SINK_REG_SYNC_CLEAR); + mask, mask); return rc; } @@ -353,17 +353,17 @@ static int wled5_mod_sync_toggle(struct wled *wled) int rc; u8 val; - val = (wled->cfg.mod_sel == MOD_A) ? WLED5_SINK_REG_SYNC_MOD_A_BIT : - WLED5_SINK_REG_SYNC_MOD_B_BIT; rc = regmap_update_bits(wled->regmap, wled->sink_addr + WLED5_SINK_REG_MOD_SYNC_BIT, - WLED5_SINK_REG_SYNC_MASK, val); + WLED5_SINK_REG_SYNC_MASK, 0); if (rc < 0) return rc; + val = (wled->cfg.mod_sel == MOD_A) ? WLED5_SINK_REG_SYNC_MOD_A_BIT : + WLED5_SINK_REG_SYNC_MOD_B_BIT; return regmap_update_bits(wled->regmap, wled->sink_addr + WLED5_SINK_REG_MOD_SYNC_BIT, - WLED5_SINK_REG_SYNC_MASK, 0); + WLED5_SINK_REG_SYNC_MASK, val); } static int wled_ovp_fault_status(struct wled *wled, bool *fault_set) -- The Qualcomm Innovation Center, Inc. is a member of the Code Aurora Forum, a Linux Foundation Collaborative Project ^ permalink raw reply related [flat|nested] 4+ messages in thread
* Re: [PATCH V3 2/2] backlight: qcom-wled: Correct the sync_toggle sequence 2021-03-01 9:28 ` [PATCH V3 2/2] backlight: qcom-wled: Correct the sync_toggle sequence Kiran Gunda @ 2021-03-01 10:02 ` Daniel Thompson 2021-03-01 16:42 ` kgunda 0 siblings, 1 reply; 4+ messages in thread From: Daniel Thompson @ 2021-03-01 10:02 UTC (permalink / raw) To: Kiran Gunda Cc: bjorn.andersson, jingoohan1, lee.jones, b.zolnierkie, dri-devel, jacek.anaszewski, pavel, robh+dt, mark.rutland, linux-leds, devicetree, linux-kernel, Andy Gross, linux-arm-msm, linux-fbdev, phone-devel On Mon, Mar 01, 2021 at 02:58:36PM +0530, Kiran Gunda wrote: > As per the current implementation, after FSC (Full Scale Current) > and brightness update the sync bits are transitioned from set-then-clear. This does not makes sense since there are too many verbs. Set and clear are both verbs so in this context: "the code will set the bit and then the code will clear the bit". Either: s/transitioned from set-then-clear/set-then-cleared/. Or: s/transitioned from set-then-clear/using a set-then-clear approach/. > But, the FSC and brightness sync takes place during a clear-then-set > transition of the sync bits. Likewise this no longer makes sense and had also become misleading. Two changes of state, clear and then set, do not usually result in a single transition. Either: s/clear-then-set/0 to 1/ Alternatively, if you want to stick exclusively to the set/clear terminology then replace the whole quoted section with: But, the FSC and brightness sync takes place when the sync bits are set (e.g. on a rising edge). > So the hardware team recommends a > clear-then-set approach in order to guarantee such a transition > regardless of the previous register state. > > Signed-off-by: Kiran Gunda <kgunda@codeaurora.org> With one of each of the changes proposed above: Reviewed-by: Daniel Thompson <daniel.thompson@linaro.org> Daniel. > --- > drivers/video/backlight/qcom-wled.c | 12 ++++++------ > 1 file changed, 6 insertions(+), 6 deletions(-) > > diff --git a/drivers/video/backlight/qcom-wled.c b/drivers/video/backlight/qcom-wled.c > index aef52b9..19f83ac 100644 > --- a/drivers/video/backlight/qcom-wled.c > +++ b/drivers/video/backlight/qcom-wled.c > @@ -337,13 +337,13 @@ static int wled3_sync_toggle(struct wled *wled) > > rc = regmap_update_bits(wled->regmap, > wled->ctrl_addr + WLED3_SINK_REG_SYNC, > - mask, mask); > + mask, WLED3_SINK_REG_SYNC_CLEAR); > if (rc < 0) > return rc; > > rc = regmap_update_bits(wled->regmap, > wled->ctrl_addr + WLED3_SINK_REG_SYNC, > - mask, WLED3_SINK_REG_SYNC_CLEAR); > + mask, mask); > > return rc; > } > @@ -353,17 +353,17 @@ static int wled5_mod_sync_toggle(struct wled *wled) > int rc; > u8 val; > > - val = (wled->cfg.mod_sel == MOD_A) ? WLED5_SINK_REG_SYNC_MOD_A_BIT : > - WLED5_SINK_REG_SYNC_MOD_B_BIT; > rc = regmap_update_bits(wled->regmap, > wled->sink_addr + WLED5_SINK_REG_MOD_SYNC_BIT, > - WLED5_SINK_REG_SYNC_MASK, val); > + WLED5_SINK_REG_SYNC_MASK, 0); > if (rc < 0) > return rc; > > + val = (wled->cfg.mod_sel == MOD_A) ? WLED5_SINK_REG_SYNC_MOD_A_BIT : > + WLED5_SINK_REG_SYNC_MOD_B_BIT; > return regmap_update_bits(wled->regmap, > wled->sink_addr + WLED5_SINK_REG_MOD_SYNC_BIT, > - WLED5_SINK_REG_SYNC_MASK, 0); > + WLED5_SINK_REG_SYNC_MASK, val); > } > > static int wled_ovp_fault_status(struct wled *wled, bool *fault_set) > -- > The Qualcomm Innovation Center, Inc. is a member of the Code Aurora Forum, > a Linux Foundation Collaborative Project > ^ permalink raw reply [flat|nested] 4+ messages in thread
* Re: [PATCH V3 2/2] backlight: qcom-wled: Correct the sync_toggle sequence 2021-03-01 10:02 ` Daniel Thompson @ 2021-03-01 16:42 ` kgunda 0 siblings, 0 replies; 4+ messages in thread From: kgunda @ 2021-03-01 16:42 UTC (permalink / raw) To: Daniel Thompson Cc: bjorn.andersson, jingoohan1, lee.jones, b.zolnierkie, dri-devel, jacek.anaszewski, pavel, robh+dt, mark.rutland, linux-leds, devicetree, linux-kernel, Andy Gross, linux-arm-msm, linux-fbdev, phone-devel On 2021-03-01 15:32, Daniel Thompson wrote: > On Mon, Mar 01, 2021 at 02:58:36PM +0530, Kiran Gunda wrote: >> As per the current implementation, after FSC (Full Scale Current) >> and brightness update the sync bits are transitioned from >> set-then-clear. > > This does not makes sense since there are too many verbs. Set and clear > are both verbs so in this context: "the code will set the bit and then > the code will clear the bit". > > Either: > > s/transitioned from set-then-clear/set-then-cleared/. > > Or: > > s/transitioned from set-then-clear/using a set-then-clear approach/. > >> But, the FSC and brightness sync takes place during a clear-then-set >> transition of the sync bits. > > Likewise this no longer makes sense and had also become misleading. > Two changes of state, clear and then set, do not usually result in a > single transition. > > Either: > > s/clear-then-set/0 to 1/ > > Alternatively, if you want to stick exclusively to the set/clear > terminology then replace the whole quoted section with: > > But, the FSC and brightness sync takes place when the sync bits are > set (e.g. on a rising edge). > > >> So the hardware team recommends a >> clear-then-set approach in order to guarantee such a transition >> regardless of the previous register state. >> >> Signed-off-by: Kiran Gunda <kgunda@codeaurora.org> > > With one of each of the changes proposed above: > Reviewed-by: Daniel Thompson <daniel.thompson@linaro.org> > > > Daniel. > Apologies for the mistake. I have corrected and submitted the V4 series with the "reviewed-by" tag. > >> --- >> drivers/video/backlight/qcom-wled.c | 12 ++++++------ >> 1 file changed, 6 insertions(+), 6 deletions(-) >> >> diff --git a/drivers/video/backlight/qcom-wled.c >> b/drivers/video/backlight/qcom-wled.c >> index aef52b9..19f83ac 100644 >> --- a/drivers/video/backlight/qcom-wled.c >> +++ b/drivers/video/backlight/qcom-wled.c >> @@ -337,13 +337,13 @@ static int wled3_sync_toggle(struct wled *wled) >> >> rc = regmap_update_bits(wled->regmap, >> wled->ctrl_addr + WLED3_SINK_REG_SYNC, >> - mask, mask); >> + mask, WLED3_SINK_REG_SYNC_CLEAR); >> if (rc < 0) >> return rc; >> >> rc = regmap_update_bits(wled->regmap, >> wled->ctrl_addr + WLED3_SINK_REG_SYNC, >> - mask, WLED3_SINK_REG_SYNC_CLEAR); >> + mask, mask); >> >> return rc; >> } >> @@ -353,17 +353,17 @@ static int wled5_mod_sync_toggle(struct wled >> *wled) >> int rc; >> u8 val; >> >> - val = (wled->cfg.mod_sel == MOD_A) ? WLED5_SINK_REG_SYNC_MOD_A_BIT : >> - WLED5_SINK_REG_SYNC_MOD_B_BIT; >> rc = regmap_update_bits(wled->regmap, >> wled->sink_addr + WLED5_SINK_REG_MOD_SYNC_BIT, >> - WLED5_SINK_REG_SYNC_MASK, val); >> + WLED5_SINK_REG_SYNC_MASK, 0); >> if (rc < 0) >> return rc; >> >> + val = (wled->cfg.mod_sel == MOD_A) ? WLED5_SINK_REG_SYNC_MOD_A_BIT : >> + WLED5_SINK_REG_SYNC_MOD_B_BIT; >> return regmap_update_bits(wled->regmap, >> wled->sink_addr + WLED5_SINK_REG_MOD_SYNC_BIT, >> - WLED5_SINK_REG_SYNC_MASK, 0); >> + WLED5_SINK_REG_SYNC_MASK, val); >> } >> >> static int wled_ovp_fault_status(struct wled *wled, bool *fault_set) >> -- >> The Qualcomm Innovation Center, Inc. is a member of the Code Aurora >> Forum, >> a Linux Foundation Collaborative Project >> ^ permalink raw reply [flat|nested] 4+ messages in thread
end of thread, other threads:[~2021-03-01 16:46 UTC | newest] Thread overview: 4+ messages (download: mbox.gz / follow: Atom feed) -- links below jump to the message on this page -- [not found] <1614590916-27070-1-git-send-email-kgunda@codeaurora.org> 2021-03-01 9:28 ` [PATCH V3 1/2] backlight: qcom-wled: Fix FSC update issue for WLED5 Kiran Gunda 2021-03-01 9:28 ` [PATCH V3 2/2] backlight: qcom-wled: Correct the sync_toggle sequence Kiran Gunda 2021-03-01 10:02 ` Daniel Thompson 2021-03-01 16:42 ` kgunda
This is a public inbox, see mirroring instructions for how to clone and mirror all data and code used for this inbox; as well as URLs for NNTP newsgroup(s).