[PATCH AUTOSEL 4.4 26/53] gpio: omap: fix lack of irqstatus_raw0 for OMAP4

[PATCH AUTOSEL 4.4 26/53] gpio: omap: fix lack of irqstatus_raw0 for OMAP4

[Sasha Levin]

From: Russell King <rmk+kernel@armlinux.org.uk>

[ Upstream commit 64ea3e9094a1f13b96c33244a3fb3a0f45690bd2 ]

Commit 384ebe1c2849 ("gpio/omap: Add DT support to GPIO driver") added
the register definition tables to the gpio-omap driver. Subsequently to
that commit, commit 4e962e8998cc ("gpio/omap: remove cpu_is_omapxxxx()
checks from *_runtime_resume()") added definitions for irqstatus_raw*
registers to the legacy OMAP4 definitions, but missed the DT
definitions.

This causes an unintentional change of behaviour for the 1.101 errata
workaround on OMAP4 platforms. Fix this oversight.

Fixes: 4e962e8998cc ("gpio/omap: remove cpu_is_omapxxxx() checks from *_runtime_resume()")
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Tested-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 drivers/gpio/gpio-omap.c | 2 ++
 1 file changed, 2 insertions(+)

diff --git a/drivers/gpio/gpio-omap.c b/drivers/gpio/gpio-omap.c
index c8c49b1d5f9f..f23136825a6e 100644
--- a/drivers/gpio/gpio-omap.c
+++ b/drivers/gpio/gpio-omap.c
@@ -1611,6 +1611,8 @@ static struct omap_gpio_reg_offs omap4_gpio_regs = {
 	.clr_dataout =		OMAP4_GPIO_CLEARDATAOUT,
 	.irqstatus =		OMAP4_GPIO_IRQSTATUS0,
 	.irqstatus2 =		OMAP4_GPIO_IRQSTATUS1,
+	.irqstatus_raw0 =	OMAP4_GPIO_IRQSTATUSRAW0,
+	.irqstatus_raw1 =	OMAP4_GPIO_IRQSTATUSRAW1,
 	.irqenable =		OMAP4_GPIO_IRQSTATUSSET0,
 	.irqenable2 =		OMAP4_GPIO_IRQSTATUSSET1,
 	.set_irqenable =	OMAP4_GPIO_IRQSTATUSSET0,
-- 
2.20.1

[PATCH AUTOSEL 4.4 27/53] gpio: omap: ensure irq is enabled before wakeup

[Sasha Levin]

From: Russell King <rmk+kernel@armlinux.org.uk>

[ Upstream commit c859e0d479b3b4f6132fc12637c51e01492f31f6 ]

Documentation states:

  NOTE: There must be a correlation between the wake-up enable and
  interrupt-enable registers. If a GPIO pin has a wake-up configured
  on it, it must also have the corresponding interrupt enabled (on
  one of the two interrupt lines).

Ensure that this condition is always satisfied by enabling the detection
events after enabling the interrupt, and disabling the detection before
disabling the interrupt.  This ensures interrupt/wakeup events can not
happen until both the wakeup and interrupt enables correlate.

If we do any clearing, clear between the interrupt enable/disable and
trigger setting.

Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Tested-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 drivers/gpio/gpio-omap.c | 15 ++++++++-------
 1 file changed, 8 insertions(+), 7 deletions(-)

diff --git a/drivers/gpio/gpio-omap.c b/drivers/gpio/gpio-omap.c
index f23136825a6e..6e65c02baad1 100644
--- a/drivers/gpio/gpio-omap.c
+++ b/drivers/gpio/gpio-omap.c
@@ -821,9 +821,9 @@ static void omap_gpio_irq_shutdown(struct irq_data *d)
 
 	raw_spin_lock_irqsave(&bank->lock, flags);
 	bank->irq_usage &= ~(BIT(offset));
-	omap_set_gpio_irqenable(bank, offset, 0);
-	omap_clear_gpio_irqstatus(bank, offset);
 	omap_set_gpio_triggering(bank, offset, IRQ_TYPE_NONE);
+	omap_clear_gpio_irqstatus(bank, offset);
+	omap_set_gpio_irqenable(bank, offset, 0);
 	if (!LINE_USED(bank->mod_usage, offset))
 		omap_clear_gpio_debounce(bank, offset);
 	omap_disable_gpio_module(bank, offset);
@@ -865,8 +865,8 @@ static void omap_gpio_mask_irq(struct irq_data *d)
 	unsigned long flags;
 
 	raw_spin_lock_irqsave(&bank->lock, flags);
-	omap_set_gpio_irqenable(bank, offset, 0);
 	omap_set_gpio_triggering(bank, offset, IRQ_TYPE_NONE);
+	omap_set_gpio_irqenable(bank, offset, 0);
 	raw_spin_unlock_irqrestore(&bank->lock, flags);
 }
 
@@ -878,9 +878,6 @@ static void omap_gpio_unmask_irq(struct irq_data *d)
 	unsigned long flags;
 
 	raw_spin_lock_irqsave(&bank->lock, flags);
-	if (trigger)
-		omap_set_gpio_triggering(bank, offset, trigger);
-
 	omap_set_gpio_irqenable(bank, offset, 1);
 
 	/*
@@ -888,9 +885,13 @@ static void omap_gpio_unmask_irq(struct irq_data *d)
 	 * is cleared, thus after the handler has run. OMAP4 needs this done
 	 * after enabing the interrupt to clear the wakeup status.
 	 */
-	if (bank->level_mask & BIT(offset))
+	if (bank->regs->leveldetect0 && bank->regs->wkup_en &&
+	    trigger & (IRQ_TYPE_LEVEL_HIGH | IRQ_TYPE_LEVEL_LOW))
 		omap_clear_gpio_irqstatus(bank, offset);
 
+	if (trigger)
+		omap_set_gpio_triggering(bank, offset, trigger);
+
 	raw_spin_unlock_irqrestore(&bank->lock, flags);
 }
 
-- 
2.20.1