Re: [PATCH v2 1/4] dt-bindings: hwmon: Add Aspeed AST2600 PWM/Fan

[Rob Herring <robh@kernel.org>]

On Wed, Jan 13, 2021 at 07:08:45AM +0000, Troy Lee wrote:
> We add binding for supporting a new AST2600 PWM/Fan hwmon driver.
> 
> Changes since v1:
> - dt binding with DT schema format
> 
> Signed-off-by: Troy Lee <troy_lee@aspeedtech.com>
> ---
>  .../hwmon/aspeed,ast2600-pwm-tachometer.yaml  | 137 ++++++++++++++++++
>  1 file changed, 137 insertions(+)
>  create mode 100644 Documentation/devicetree/bindings/hwmon/aspeed,ast2600-pwm-tachometer.yaml
> 
> diff --git a/Documentation/devicetree/bindings/hwmon/aspeed,ast2600-pwm-tachometer.yaml b/Documentation/devicetree/bindings/hwmon/aspeed,ast2600-pwm-tachometer.yaml
> new file mode 100644
> index 000000000000..b84076a4a338
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/hwmon/aspeed,ast2600-pwm-tachometer.yaml
> @@ -0,0 +1,137 @@
> +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
> +%YAML 1.2
> +---
> +
> +$id: http://devicetree.org/schemas/hwmon/aspeed,ast2600-pwm-tachometer.yaml#
> +$schema: http://devicetree.org/meta-schemas/core.yaml#
> +
> +title: ASPEED AST2600 PWM and Fan Tacho controller device driver
> +
> +maintainers:
> +  - Ryan Chen <ryan_chen@aspeedtech.com>
> +
> +description: |
> +  The ASPEED PWM controller can support upto 16 PWM outputs. The ASPEED Fan Tacho
> +  controller can support upto 16 Fan tachometer inputs.
> +  There can be upto 16 fans supported. Each fan can have one PWM output and
> +  one Fan tach inputs.
> +
> +properties:
> +  compatible:
> +    const: aspeed,ast2600-pwm-tachometer
> +
> +  "#address-cells":
> +    const: 1
> +
> +  "#size-cells":
> +    const: 0
> +
> +  "#cooling-cells":
> +    const: 2
> +
> +  reg:
> +    description:
> +      Address and length of the register set for the device.

No need for generic descriptions. That's every 'reg'.

What you need is how many entries and what each one is if more than 1. 
If only 1, then just 'maxItems: 1'

> +
> +  clocks:
> +    description:
> +      phandle to clock provider with the clock number in the second cell

Same here.

> +
> +  resets:
> +    description:
> +      phandle to reset controller with the reset number in the second cell

And here.

> +
> +patternProperties:
> +  "@[0-9]+$":

If every node is a fan and there are up to 16:

^fan@[0-9a-f]$

> +    type: object
> +    description:
> +      Under fan subnode there can upto 16 child nodes, with each child node
> +      representing a fan. There are 16 fans each fan can have one PWM port and one
> +      Fan tach inputs.
> +      For PWM port can be configured cooling-levels to create cooling device.
> +      Cooling device could be bound to a thermal zone for the thermal control.
> +
> +    properties:
> +      reg:
> +        minimum: 0
> +        maximum: 15
> +        description:
> +          This property identify the PWM control channel of this fan.
> +
> +      fan-tach-ch:
> +        $ref: /schemas/types.yaml#/definitions/uint8
> +        minimum: 0
> +        maximum: 15
> +        description:
> +          This property identify the fan tach input channel.
> +
> +      pulses-per-revolution:
> +        $ref: /schemas/types.yaml#/definitions/uint32
> +        default: 2
> +        minimum: 1
> +        description:
> +          Specify tacho pulse per revolution of the fan.
> +
> +      cooling-levels:
> +        description:
> +          PWM duty cycle values in a range from 0 to 255
> +          which correspond to thermal cooling states.
> +
> +      aspeed,pwm-freq:
> +        $ref: /schemas/types.yaml#/definitions/uint32
> +        default: 25000
> +        minimum: 24
> +        maximum: 780000
> +        description:
> +          Specify the frequency of PWM.

Units? Use a unit suffix and then drop the $ref.

> +
> +      aspeed,inverse-pin:
> +        type: boolean
> +        description:
> +          Inverse PWM output signal.
> +
> +      aspeed,falling-point:
> +        $ref: /schemas/types.yaml#/definitions/uint8
> +        default: 10
> +        minimum: 0
> +        maximum: 255

0-255 is already the range of uint8, so drop.

> +        description:
> +          Initialize the pulse width.
> +
> +    required:
> +      - fan-tach-ch
> +      - reg
> +
> +    additionalProperties: true
> +
> +required:
> + - compatible
> + - reg
> +
> +additionalProperties: false
> +
> +examples:
> +  - |
> +    pwm_tacho: pwm-tacho-controller@1e610000 {
> +        compatible = "aspeed,ast2600-pwm-tachometer";
> +        #address-cells = <1>;
> +        #size-cells = <0>;
> +        reg = <0x1e610000 0x100>;
> +
> +        fan@1 {
> +            reg = <0x00>;
> +            aspeed,pwm-freq = <25000>;
> +            cooling-levels = /bits/ 8 <125 151 177 203 229 255>;
> +            fan-tach-ch = /bits/ 8 <0x00>;
> +            pulses-per-revolution = <2>;
> +        };
> +
> +        fan@2 {
> +            reg = <0x01>;
> +            aspeed,pwm-freq = <25000>;
> +            cooling-levels = /bits/ 8 <125 151 177 203 229 255>;
> +            fan-tach-ch = /bits/ 8 <0x01>;
> +            pulses-per-revolution = <2>;
> +        };
> +    };
> +...
> -- 
> 2.25.1
>