* [PATCH 1/6] hwmon: (aquacomputer_d5next) Rename AQC_TEMP_SENSOR_SIZE to AQC_SENSOR_SIZE
2022-12-18 11:31 [PATCH 0/6] hwmon: (aquacomputer_d5next) Add Aquacomputer Aquaero sensors Leonard Anderweit
@ 2022-12-18 11:31 ` Leonard Anderweit
2022-12-18 11:31 ` [PATCH 2/6] hwmon: (aquacomputer_d5next) Restructure flow sensor reading Leonard Anderweit
` (4 subsequent siblings)
5 siblings, 0 replies; 8+ messages in thread
From: Leonard Anderweit @ 2022-12-18 11:31 UTC (permalink / raw)
To: linux-hwmon
Cc: Aleksa Savic, Jack Doan, Jean Delvare, Guenter Roeck,
Jonathan Corbet, linux-doc, linux-kernel, Leonard Anderweit
Rename AQC_TEMP_SENSOR_SIZE to AQC_SENSOR_SIZE to use with other sensor
types.
Signed-off-by: Leonard Anderweit <leonard.anderweit@gmail.com>
---
drivers/hwmon/aquacomputer_d5next.c | 10 +++++-----
1 file changed, 5 insertions(+), 5 deletions(-)
diff --git a/drivers/hwmon/aquacomputer_d5next.c b/drivers/hwmon/aquacomputer_d5next.c
index 9cc10080160b..8fd9f7fd7ec4 100644
--- a/drivers/hwmon/aquacomputer_d5next.c
+++ b/drivers/hwmon/aquacomputer_d5next.c
@@ -60,7 +60,7 @@ static u8 secondary_ctrl_report[] = {
};
/* Sensor sizes and offsets for all Aquacomputer devices */
-#define AQC_TEMP_SENSOR_SIZE 0x02
+#define AQC_SENSOR_SIZE 0x02
#define AQC_TEMP_SENSOR_DISCONNECTED 0x7FFF
#define AQC_FAN_PERCENT_OFFSET 0x00
#define AQC_FAN_VOLTAGE_OFFSET 0x02
@@ -557,7 +557,7 @@ static int aqc_read(struct device *dev, enum hwmon_sensor_types type, u32 attr,
case hwmon_temp_offset:
ret =
aqc_get_ctrl_val(priv, priv->temp_ctrl_offset +
- channel * AQC_TEMP_SENSOR_SIZE, val);
+ channel * AQC_SENSOR_SIZE, val);
if (ret < 0)
return ret;
@@ -651,7 +651,7 @@ static int aqc_write(struct device *dev, enum hwmon_sensor_types type, u32 attr,
val = clamp_val(val, -15000, 15000) / 10;
ret =
aqc_set_ctrl_val(priv, priv->temp_ctrl_offset +
- channel * AQC_TEMP_SENSOR_SIZE, val);
+ channel * AQC_SENSOR_SIZE, val);
if (ret < 0)
return ret;
break;
@@ -797,7 +797,7 @@ static int aqc_raw_event(struct hid_device *hdev, struct hid_report *report, u8
for (i = 0; i < priv->num_temp_sensors; i++) {
sensor_value = get_unaligned_be16(data +
priv->temp_sensor_start_offset +
- i * AQC_TEMP_SENSOR_SIZE);
+ i * AQC_SENSOR_SIZE);
if (sensor_value == AQC_TEMP_SENSOR_DISCONNECTED)
priv->temp_input[i] = -ENODATA;
else
@@ -808,7 +808,7 @@ static int aqc_raw_event(struct hid_device *hdev, struct hid_report *report, u8
for (j = 0; j < priv->num_virtual_temp_sensors; j++) {
sensor_value = get_unaligned_be16(data +
priv->virtual_temp_sensor_start_offset +
- j * AQC_TEMP_SENSOR_SIZE);
+ j * AQC_SENSOR_SIZE);
if (sensor_value == AQC_TEMP_SENSOR_DISCONNECTED)
priv->temp_input[i] = -ENODATA;
else
--
2.38.1
^ permalink raw reply related [flat|nested] 8+ messages in thread* [PATCH 2/6] hwmon: (aquacomputer_d5next) Restructure flow sensor reading
2022-12-18 11:31 [PATCH 0/6] hwmon: (aquacomputer_d5next) Add Aquacomputer Aquaero sensors Leonard Anderweit
2022-12-18 11:31 ` [PATCH 1/6] hwmon: (aquacomputer_d5next) Rename AQC_TEMP_SENSOR_SIZE to AQC_SENSOR_SIZE Leonard Anderweit
@ 2022-12-18 11:31 ` Leonard Anderweit
2022-12-18 11:31 ` [PATCH 3/6] hwmon: (aquacomputer_d5next) Add structure for fan layout Leonard Anderweit
` (3 subsequent siblings)
5 siblings, 0 replies; 8+ messages in thread
From: Leonard Anderweit @ 2022-12-18 11:31 UTC (permalink / raw)
To: linux-hwmon
Cc: Aleksa Savic, Jack Doan, Jean Delvare, Guenter Roeck,
Jonathan Corbet, linux-doc, linux-kernel, Leonard Anderweit
Read flow sensors the same way for all devices instead of in special
cases. Implemented by Aleksa Savic [1].
[1] https://github.com/aleksamagicka/aquacomputer_d5next-hwmon/commit/1c10912c5fdc8287d88378bcf1ef14d596f29462
Originally-from: Aleksa Savic <savicaleksa83@gmail.com>
Signed-off-by: Leonard Anderweit <leonard.anderweit@gmail.com>
---
drivers/hwmon/aquacomputer_d5next.c | 26 ++++++++++++++++++--------
1 file changed, 18 insertions(+), 8 deletions(-)
diff --git a/drivers/hwmon/aquacomputer_d5next.c b/drivers/hwmon/aquacomputer_d5next.c
index 8fd9f7fd7ec4..388bf1e33e0d 100644
--- a/drivers/hwmon/aquacomputer_d5next.c
+++ b/drivers/hwmon/aquacomputer_d5next.c
@@ -125,6 +125,7 @@ static u16 octo_ctrl_fan_offsets[] = { 0x5B, 0xB0, 0x105, 0x15A, 0x1AF, 0x204, 0
#define QUADRO_NUM_FANS 4
#define QUADRO_NUM_SENSORS 4
#define QUADRO_NUM_VIRTUAL_SENSORS 16
+#define QUADRO_NUM_FLOW_SENSORS 1
#define QUADRO_CTRL_REPORT_SIZE 0x3c1
/* Sensor report offsets for the Quadro */
@@ -141,6 +142,7 @@ static u16 quadro_ctrl_fan_offsets[] = { 0x37, 0x8c, 0xe1, 0x136 }; /* Fan speed
/* Specs of High Flow Next flow sensor */
#define HIGHFLOWNEXT_NUM_SENSORS 2
+#define HIGHFLOWNEXT_NUM_FLOW_SENSORS 1
/* Sensor report offsets for the High Flow Next */
#define HIGHFLOWNEXT_SENSOR_START 85
@@ -303,7 +305,8 @@ struct aqc_data {
int virtual_temp_sensor_start_offset;
u16 temp_ctrl_offset;
u16 power_cycle_count_offset;
- u8 flow_sensor_offset;
+ int num_flow_sensors;
+ u8 flow_sensors_start_offset;
u8 flow_pulses_ctrl_offset;
/* General info, same across all devices */
@@ -475,8 +478,8 @@ static umode_t aqc_is_visible(const void *data, enum hwmon_sensor_types type, u3
return 0444;
break;
case quadro:
- /* Special case to support flow sensor */
- if (channel < priv->num_fans + 1)
+ /* Special case to support flow sensors */
+ if (channel < priv->num_fans + priv->num_flow_sensors)
return 0444;
break;
default:
@@ -830,6 +833,13 @@ static int aqc_raw_event(struct hid_device *hdev, struct hid_report *report, u8
get_unaligned_be16(data + priv->fan_sensor_offsets[i] + AQC_FAN_CURRENT_OFFSET);
}
+ /* Flow sensor readings */
+ for (j = 0; j < priv->num_flow_sensors; j++) {
+ priv->speed_input[i] = get_unaligned_be16(data + priv->flow_sensors_start_offset +
+ j * AQC_SENSOR_SIZE);
+ i++;
+ }
+
if (priv->power_cycle_count_offset != 0)
priv->power_cycles = get_unaligned_be32(data + priv->power_cycle_count_offset);
@@ -839,9 +849,6 @@ static int aqc_raw_event(struct hid_device *hdev, struct hid_report *report, u8
priv->voltage_input[2] = get_unaligned_be16(data + D5NEXT_5V_VOLTAGE) * 10;
priv->voltage_input[3] = get_unaligned_be16(data + D5NEXT_12V_VOLTAGE) * 10;
break;
- case quadro:
- priv->speed_input[4] = get_unaligned_be16(data + priv->flow_sensor_offset);
- break;
case highflownext:
/* If external temp sensor is not connected, its power reading is also N/A */
if (priv->temp_input[1] == -ENODATA)
@@ -854,7 +861,6 @@ static int aqc_raw_event(struct hid_device *hdev, struct hid_report *report, u8
priv->voltage_input[1] =
get_unaligned_be16(data + HIGHFLOWNEXT_5V_VOLTAGE_USB) * 10;
- priv->speed_input[0] = get_unaligned_be16(data + HIGHFLOWNEXT_FLOW);
priv->speed_input[1] = get_unaligned_be16(data + HIGHFLOWNEXT_WATER_QUALITY);
priv->speed_input[2] = get_unaligned_be16(data + HIGHFLOWNEXT_CONDUCTIVITY);
break;
@@ -1034,11 +1040,13 @@ static int aqc_probe(struct hid_device *hdev, const struct hid_device_id *id)
priv->temp_sensor_start_offset = QUADRO_SENSOR_START;
priv->num_virtual_temp_sensors = QUADRO_NUM_VIRTUAL_SENSORS;
priv->virtual_temp_sensor_start_offset = QUADRO_VIRTUAL_SENSORS_START;
+ priv->num_flow_sensors = QUADRO_NUM_FLOW_SENSORS;
+ priv->flow_sensors_start_offset = QUADRO_FLOW_SENSOR_OFFSET;
+
priv->temp_ctrl_offset = QUADRO_TEMP_CTRL_OFFSET;
priv->buffer_size = QUADRO_CTRL_REPORT_SIZE;
- priv->flow_sensor_offset = QUADRO_FLOW_SENSOR_OFFSET;
priv->flow_pulses_ctrl_offset = QUADRO_FLOW_PULSES_CTRL_OFFSET;
priv->power_cycle_count_offset = QUADRO_POWER_CYCLES;
@@ -1056,6 +1064,8 @@ static int aqc_probe(struct hid_device *hdev, const struct hid_device_id *id)
priv->num_temp_sensors = HIGHFLOWNEXT_NUM_SENSORS;
priv->temp_sensor_start_offset = HIGHFLOWNEXT_SENSOR_START;
+ priv->num_flow_sensors = HIGHFLOWNEXT_NUM_FLOW_SENSORS;
+ priv->flow_sensors_start_offset = HIGHFLOWNEXT_FLOW;
priv->power_cycle_count_offset = QUADRO_POWER_CYCLES;
--
2.38.1
^ permalink raw reply related [flat|nested] 8+ messages in thread* [PATCH 3/6] hwmon: (aquacomputer_d5next) Add structure for fan layout
2022-12-18 11:31 [PATCH 0/6] hwmon: (aquacomputer_d5next) Add Aquacomputer Aquaero sensors Leonard Anderweit
2022-12-18 11:31 ` [PATCH 1/6] hwmon: (aquacomputer_d5next) Rename AQC_TEMP_SENSOR_SIZE to AQC_SENSOR_SIZE Leonard Anderweit
2022-12-18 11:31 ` [PATCH 2/6] hwmon: (aquacomputer_d5next) Restructure flow sensor reading Leonard Anderweit
@ 2022-12-18 11:31 ` Leonard Anderweit
2022-12-18 11:31 ` [PATCH 4/6] hwmon: (aquacomputer_d5next) Device dependent serial number and firmware offsets Leonard Anderweit
` (2 subsequent siblings)
5 siblings, 0 replies; 8+ messages in thread
From: Leonard Anderweit @ 2022-12-18 11:31 UTC (permalink / raw)
To: linux-hwmon
Cc: Aleksa Savic, Jack Doan, Jean Delvare, Guenter Roeck,
Jonathan Corbet, linux-doc, linux-kernel, Leonard Anderweit
Introduce structure for per device fan sensor offsets. This allows
reading fan sensors in aqc_raw_event() from devices which use a
different sensor layout in their status HID report. Currently only one
version is implemented as all supported devices use the same structure.
Signed-off-by: Leonard Anderweit <leonard.anderweit@gmail.com>
---
drivers/hwmon/aquacomputer_d5next.c | 28 ++++++++++++++++++++++++----
1 file changed, 24 insertions(+), 4 deletions(-)
diff --git a/drivers/hwmon/aquacomputer_d5next.c b/drivers/hwmon/aquacomputer_d5next.c
index 388bf1e33e0d..1ea866fcd3ec 100644
--- a/drivers/hwmon/aquacomputer_d5next.c
+++ b/drivers/hwmon/aquacomputer_d5next.c
@@ -282,6 +282,21 @@ static const char *const label_highflownext_voltage[] = {
"+5V USB voltage"
};
+struct aqc_fan_structure_offsets {
+ u8 voltage;
+ u8 curr;
+ u8 power;
+ u8 speed;
+};
+
+/* Fan structure offsets for all devices except Aquaero */
+static struct aqc_fan_structure_offsets aqc_general_fan_structure = {
+ .voltage = AQC_FAN_VOLTAGE_OFFSET,
+ .curr = AQC_FAN_CURRENT_OFFSET,
+ .power = AQC_FAN_POWER_OFFSET,
+ .speed = AQC_FAN_SPEED_OFFSET
+};
+
struct aqc_data {
struct hid_device *hdev;
struct device *hwmon_dev;
@@ -308,6 +323,7 @@ struct aqc_data {
int num_flow_sensors;
u8 flow_sensors_start_offset;
u8 flow_pulses_ctrl_offset;
+ struct aqc_fan_structure_offsets *fan_structure;
/* General info, same across all devices */
u32 serial_number[2];
@@ -822,15 +838,17 @@ static int aqc_raw_event(struct hid_device *hdev, struct hid_report *report, u8
/* Fan speed and related readings */
for (i = 0; i < priv->num_fans; i++) {
priv->speed_input[i] =
- get_unaligned_be16(data + priv->fan_sensor_offsets[i] + AQC_FAN_SPEED_OFFSET);
+ get_unaligned_be16(data + priv->fan_sensor_offsets[i] +
+ priv->fan_structure->speed);
priv->power_input[i] =
get_unaligned_be16(data + priv->fan_sensor_offsets[i] +
- AQC_FAN_POWER_OFFSET) * 10000;
+ priv->fan_structure->power) * 10000;
priv->voltage_input[i] =
get_unaligned_be16(data + priv->fan_sensor_offsets[i] +
- AQC_FAN_VOLTAGE_OFFSET) * 10;
+ priv->fan_structure->voltage) * 10;
priv->current_input[i] =
- get_unaligned_be16(data + priv->fan_sensor_offsets[i] + AQC_FAN_CURRENT_OFFSET);
+ get_unaligned_be16(data + priv->fan_sensor_offsets[i] +
+ priv->fan_structure->curr);
}
/* Flow sensor readings */
@@ -1078,6 +1096,8 @@ static int aqc_probe(struct hid_device *hdev, const struct hid_device_id *id)
break;
}
+ priv->fan_structure = &aqc_general_fan_structure;
+
if (priv->buffer_size != 0) {
priv->checksum_start = 0x01;
priv->checksum_length = priv->buffer_size - 3;
--
2.38.1
^ permalink raw reply related [flat|nested] 8+ messages in thread* [PATCH 4/6] hwmon: (aquacomputer_d5next) Device dependent serial number and firmware offsets
2022-12-18 11:31 [PATCH 0/6] hwmon: (aquacomputer_d5next) Add Aquacomputer Aquaero sensors Leonard Anderweit
` (2 preceding siblings ...)
2022-12-18 11:31 ` [PATCH 3/6] hwmon: (aquacomputer_d5next) Add structure for fan layout Leonard Anderweit
@ 2022-12-18 11:31 ` Leonard Anderweit
2022-12-18 11:31 ` [PATCH 5/6] hwmon: (aquacomputer_d5next) Make fan sensor offsets u16 Leonard Anderweit
2022-12-18 11:31 ` [PATCH 6/6] hwmon: (aquacomputer_d5next) Support sensors for Aquacomputer Aquaero Leonard Anderweit
5 siblings, 0 replies; 8+ messages in thread
From: Leonard Anderweit @ 2022-12-18 11:31 UTC (permalink / raw)
To: linux-hwmon
Cc: Aleksa Savic, Jack Doan, Jean Delvare, Guenter Roeck,
Jonathan Corbet, linux-doc, linux-kernel, Leonard Anderweit
Add device dependent serial number and firmware offsets to support
devices with different offsets. All currently supported devices share
the same offsets. Implemented by Aleksa Savic [1].
[1] https://github.com/aleksamagicka/aquacomputer_d5next-hwmon/pull/31/commits/14c3acf78b17397edb5dd356e6f5943a9996a1f9
Originally-from: Aleksa Savic <savicaleksa83@gmail.com>
Signed-off-by: Leonard Anderweit <leonard.anderweit@gmail.com>
---
drivers/hwmon/aquacomputer_d5next.c | 21 ++++++++++++++-------
1 file changed, 14 insertions(+), 7 deletions(-)
diff --git a/drivers/hwmon/aquacomputer_d5next.c b/drivers/hwmon/aquacomputer_d5next.c
index 1ea866fcd3ec..cc53231067f4 100644
--- a/drivers/hwmon/aquacomputer_d5next.c
+++ b/drivers/hwmon/aquacomputer_d5next.c
@@ -43,9 +43,7 @@ static const char *const aqc_device_names[] = {
#define STATUS_REPORT_ID 0x01
#define STATUS_UPDATE_INTERVAL (2 * HZ) /* In seconds */
-#define SERIAL_FIRST_PART 3
-#define SERIAL_SECOND_PART 5
-#define FIRMWARE_VERSION 13
+#define SERIAL_PART_OFFSET 2
#define CTRL_REPORT_ID 0x03
@@ -59,7 +57,10 @@ static u8 secondary_ctrl_report[] = {
0x02, 0x00, 0x00, 0x00, 0x02, 0x00, 0x00, 0x00, 0x00, 0x34, 0xC6
};
-/* Sensor sizes and offsets for all Aquacomputer devices */
+/* Info, sensor sizes and offsets for all Aquacomputer devices */
+#define AQC_SERIAL_START 0x3
+#define AQC_FIRMWARE_VERSION 0xD
+
#define AQC_SENSOR_SIZE 0x02
#define AQC_TEMP_SENSOR_DISCONNECTED 0x7FFF
#define AQC_FAN_PERCENT_OFFSET 0x00
@@ -326,7 +327,9 @@ struct aqc_data {
struct aqc_fan_structure_offsets *fan_structure;
/* General info, same across all devices */
+ u8 serial_number_start_offset;
u32 serial_number[2];
+ u8 firmware_version_offset;
u16 firmware_version;
/* How many times the device was powered on, if available */
@@ -808,9 +811,10 @@ static int aqc_raw_event(struct hid_device *hdev, struct hid_report *report, u8
priv = hid_get_drvdata(hdev);
/* Info provided with every report */
- priv->serial_number[0] = get_unaligned_be16(data + SERIAL_FIRST_PART);
- priv->serial_number[1] = get_unaligned_be16(data + SERIAL_SECOND_PART);
- priv->firmware_version = get_unaligned_be16(data + FIRMWARE_VERSION);
+ priv->serial_number[0] = get_unaligned_be16(data + priv->serial_number_start_offset);
+ priv->serial_number[1] = get_unaligned_be16(data + priv->serial_number_start_offset +
+ SERIAL_PART_OFFSET);
+ priv->firmware_version = get_unaligned_be16(data + priv->firmware_version_offset);
/* Physical temperature sensor readings */
for (i = 0; i < priv->num_temp_sensors; i++) {
@@ -1096,6 +1100,9 @@ static int aqc_probe(struct hid_device *hdev, const struct hid_device_id *id)
break;
}
+ priv->serial_number_start_offset = AQC_SERIAL_START;
+ priv->firmware_version_offset = AQC_FIRMWARE_VERSION;
+
priv->fan_structure = &aqc_general_fan_structure;
if (priv->buffer_size != 0) {
--
2.38.1
^ permalink raw reply related [flat|nested] 8+ messages in thread* [PATCH 5/6] hwmon: (aquacomputer_d5next) Make fan sensor offsets u16
2022-12-18 11:31 [PATCH 0/6] hwmon: (aquacomputer_d5next) Add Aquacomputer Aquaero sensors Leonard Anderweit
` (3 preceding siblings ...)
2022-12-18 11:31 ` [PATCH 4/6] hwmon: (aquacomputer_d5next) Device dependent serial number and firmware offsets Leonard Anderweit
@ 2022-12-18 11:31 ` Leonard Anderweit
2022-12-18 11:31 ` [PATCH 6/6] hwmon: (aquacomputer_d5next) Support sensors for Aquacomputer Aquaero Leonard Anderweit
5 siblings, 0 replies; 8+ messages in thread
From: Leonard Anderweit @ 2022-12-18 11:31 UTC (permalink / raw)
To: linux-hwmon
Cc: Aleksa Savic, Jack Doan, Jean Delvare, Guenter Roeck,
Jonathan Corbet, linux-doc, linux-kernel, Leonard Anderweit
Make fan sensor offsets u16 as u8 is insufficient for upcoming devices.
Signed-off-by: Leonard Anderweit <leonard.anderweit@gmail.com>
---
drivers/hwmon/aquacomputer_d5next.c | 8 ++++----
1 file changed, 4 insertions(+), 4 deletions(-)
diff --git a/drivers/hwmon/aquacomputer_d5next.c b/drivers/hwmon/aquacomputer_d5next.c
index cc53231067f4..d28d7079917a 100644
--- a/drivers/hwmon/aquacomputer_d5next.c
+++ b/drivers/hwmon/aquacomputer_d5next.c
@@ -83,7 +83,7 @@ static u8 secondary_ctrl_report[] = {
#define D5NEXT_5V_VOLTAGE 0x39
#define D5NEXT_12V_VOLTAGE 0x37
#define D5NEXT_VIRTUAL_SENSORS_START 0x3f
-static u8 d5next_sensor_fan_offsets[] = { D5NEXT_PUMP_OFFSET, D5NEXT_FAN_OFFSET };
+static u16 d5next_sensor_fan_offsets[] = { D5NEXT_PUMP_OFFSET, D5NEXT_FAN_OFFSET };
/* Control report offsets for the D5 Next pump */
#define D5NEXT_TEMP_CTRL_OFFSET 0x2D /* Temperature sensor offsets location */
@@ -115,7 +115,7 @@ static u16 d5next_ctrl_fan_offsets[] = { 0x97, 0x42 }; /* Pump and fan speed (fr
#define OCTO_POWER_CYCLES 0x18
#define OCTO_SENSOR_START 0x3D
#define OCTO_VIRTUAL_SENSORS_START 0x45
-static u8 octo_sensor_fan_offsets[] = { 0x7D, 0x8A, 0x97, 0xA4, 0xB1, 0xBE, 0xCB, 0xD8 };
+static u16 octo_sensor_fan_offsets[] = { 0x7D, 0x8A, 0x97, 0xA4, 0xB1, 0xBE, 0xCB, 0xD8 };
/* Control report offsets for the Octo */
#define OCTO_TEMP_CTRL_OFFSET 0xA
@@ -134,7 +134,7 @@ static u16 octo_ctrl_fan_offsets[] = { 0x5B, 0xB0, 0x105, 0x15A, 0x1AF, 0x204, 0
#define QUADRO_SENSOR_START 0x34
#define QUADRO_VIRTUAL_SENSORS_START 0x3c
#define QUADRO_FLOW_SENSOR_OFFSET 0x6e
-static u8 quadro_sensor_fan_offsets[] = { 0x70, 0x7D, 0x8A, 0x97 };
+static u16 quadro_sensor_fan_offsets[] = { 0x70, 0x7D, 0x8A, 0x97 };
/* Control report offsets for the Quadro */
#define QUADRO_TEMP_CTRL_OFFSET 0xA
@@ -313,7 +313,7 @@ struct aqc_data {
int checksum_offset;
int num_fans;
- u8 *fan_sensor_offsets;
+ u16 *fan_sensor_offsets;
u16 *fan_ctrl_offsets;
int num_temp_sensors;
int temp_sensor_start_offset;
--
2.38.1
^ permalink raw reply related [flat|nested] 8+ messages in thread* [PATCH 6/6] hwmon: (aquacomputer_d5next) Support sensors for Aquacomputer Aquaero
2022-12-18 11:31 [PATCH 0/6] hwmon: (aquacomputer_d5next) Add Aquacomputer Aquaero sensors Leonard Anderweit
` (4 preceding siblings ...)
2022-12-18 11:31 ` [PATCH 5/6] hwmon: (aquacomputer_d5next) Make fan sensor offsets u16 Leonard Anderweit
@ 2022-12-18 11:31 ` Leonard Anderweit
2022-12-29 14:20 ` Guenter Roeck
5 siblings, 1 reply; 8+ messages in thread
From: Leonard Anderweit @ 2022-12-18 11:31 UTC (permalink / raw)
To: linux-hwmon
Cc: Aleksa Savic, Jack Doan, Jean Delvare, Guenter Roeck,
Jonathan Corbet, linux-doc, linux-kernel, Leonard Anderweit
Add support for reading sensors of the Aquacomputer Aquaero 5/6 fan
controllers. These fan controllers supports 4 fans, 8 physical
temperature sensors, 8 virtual temperature sensors and 2 flow sensors.
Temperature and flow sensor reading implemented by Aleksa Savic [1] [2]
[3].
[1] https://github.com/aleksamagicka/aquacomputer_d5next-hwmon/pull/31
[2] https://github.com/aleksamagicka/aquacomputer_d5next-hwmon/pull/51
[3] https://github.com/aleksamagicka/aquacomputer_d5next-hwmon/pull/55
Originally-from: Aleksa Savic <savicaleksa83@gmail.com>
Signed-off-by: Leonard Anderweit <leonard.anderweit@gmail.com>
---
Documentation/hwmon/aquacomputer_d5next.rst | 5 +
drivers/hwmon/aquacomputer_d5next.c | 108 ++++++++++++++++++--
2 files changed, 104 insertions(+), 9 deletions(-)
diff --git a/Documentation/hwmon/aquacomputer_d5next.rst b/Documentation/hwmon/aquacomputer_d5next.rst
index 637bdbc8fcad..b94ff08080bf 100644
--- a/Documentation/hwmon/aquacomputer_d5next.rst
+++ b/Documentation/hwmon/aquacomputer_d5next.rst
@@ -5,6 +5,7 @@ Kernel driver aquacomputer-d5next
Supported devices:
+* Aquacomputer Aquaero 5/6 fan controllers
* Aquacomputer D5 Next watercooling pump
* Aquacomputer Farbwerk RGB controller
* Aquacomputer Farbwerk 360 RGB controller
@@ -20,6 +21,10 @@ Description
This driver exposes hardware sensors of listed Aquacomputer devices, which
communicate through proprietary USB HID protocols.
+The Aquaero devices expose eight temperature sensors, eight virtual temperature
+sensors and two flow senors. The fans expose their speed (in RPM), power,
+voltage and current.
+
For the D5 Next pump, available sensors are pump and fan speed, power, voltage
and current, as well as coolant temperature and eight virtual temp sensors. Also
available through debugfs are the serial number, firmware version and power-on
diff --git a/drivers/hwmon/aquacomputer_d5next.c b/drivers/hwmon/aquacomputer_d5next.c
index d28d7079917a..0fd00cfb86c8 100644
--- a/drivers/hwmon/aquacomputer_d5next.c
+++ b/drivers/hwmon/aquacomputer_d5next.c
@@ -1,7 +1,7 @@
// SPDX-License-Identifier: GPL-2.0+
/*
* hwmon driver for Aquacomputer devices (D5 Next, Farbwerk, Farbwerk 360, Octo,
- * Quadro, High Flow Next)
+ * Quadro, High Flow Next, Aquaero)
*
* Aquacomputer devices send HID reports (with ID 0x01) every second to report
* sensor values.
@@ -21,6 +21,7 @@
#include <asm/unaligned.h>
#define USB_VENDOR_ID_AQUACOMPUTER 0x0c70
+#define USB_PRODUCT_ID_AQUAERO 0xf001
#define USB_PRODUCT_ID_FARBWERK 0xf00a
#define USB_PRODUCT_ID_QUADRO 0xf00d
#define USB_PRODUCT_ID_D5NEXT 0xf00e
@@ -28,7 +29,7 @@
#define USB_PRODUCT_ID_OCTO 0xf011
#define USB_PRODUCT_ID_HIGHFLOWNEXT 0xf012
-enum kinds { d5next, farbwerk, farbwerk360, octo, quadro, highflownext };
+enum kinds { d5next, farbwerk, farbwerk360, octo, quadro, highflownext, aquaero };
static const char *const aqc_device_names[] = {
[d5next] = "d5next",
@@ -36,7 +37,8 @@ static const char *const aqc_device_names[] = {
[farbwerk360] = "farbwerk360",
[octo] = "octo",
[quadro] = "quadro",
- [highflownext] = "highflownext"
+ [highflownext] = "highflownext",
+ [aquaero] = "aquaero"
};
#define DRIVER_NAME "aquacomputer_d5next"
@@ -57,7 +59,7 @@ static u8 secondary_ctrl_report[] = {
0x02, 0x00, 0x00, 0x00, 0x02, 0x00, 0x00, 0x00, 0x00, 0x34, 0xC6
};
-/* Info, sensor sizes and offsets for all Aquacomputer devices */
+/* Info, sensor sizes and offsets for most Aquacomputer devices */
#define AQC_SERIAL_START 0x3
#define AQC_FIRMWARE_VERSION 0xD
@@ -69,6 +71,24 @@ static u8 secondary_ctrl_report[] = {
#define AQC_FAN_POWER_OFFSET 0x06
#define AQC_FAN_SPEED_OFFSET 0x08
+/* Specs of the Aquaero fan controllers */
+#define AQUAERO_SERIAL_START 0x07
+#define AQUAERO_FIRMWARE_VERSION 0x0B
+#define AQUAERO_NUM_FANS 4
+#define AQUAERO_NUM_SENSORS 8
+#define AQUAERO_NUM_VIRTUAL_SENSORS 8
+#define AQUAERO_NUM_FLOW_SENSORS 2
+
+/* Sensor report offsets for Aquaero fan controllers */
+#define AQUAERO_SENSOR_START 0x65
+#define AQUAERO_VIRTUAL_SENSOR_START 0x85
+#define AQUAERO_FLOW_SENSORS_START 0xF9
+#define AQUAERO_FAN_VOLTAGE_OFFSET 0x04
+#define AQUAERO_FAN_CURRENT_OFFSET 0x06
+#define AQUAERO_FAN_POWER_OFFSET 0x08
+#define AQUAERO_FAN_SPEED_OFFSET 0x00
+static u16 aquaero_sensor_fan_offsets[] = { 0x167, 0x173, 0x17f, 0x18B };
+
/* Specs of the D5 Next pump */
#define D5NEXT_NUM_FANS 2
#define D5NEXT_NUM_SENSORS 1
@@ -181,12 +201,16 @@ static const char *const label_d5next_current[] = {
"Fan current"
};
-/* Labels for Farbwerk, Farbwerk 360 and Octo and Quadro temperature sensors */
+/* Labels for Aquaero, Farbwerk, Farbwerk 360 and Octo and Quadro temperature sensors */
static const char *const label_temp_sensors[] = {
"Sensor 1",
"Sensor 2",
"Sensor 3",
- "Sensor 4"
+ "Sensor 4",
+ "Sensor 5",
+ "Sensor 6",
+ "Sensor 7",
+ "Sensor 8"
};
static const char *const label_virtual_temp_sensors[] = {
@@ -262,6 +286,16 @@ static const char *const label_quadro_speeds[] = {
"Flow speed [dL/h]"
};
+/* Labels for Aquaero fan speeds */
+static const char *const label_aquaero_speeds[] = {
+ "Fan 1 speed",
+ "Fan 2 speed",
+ "Fan 3 speed",
+ "Fan 4 speed",
+ "Flow sensor 1 [dL/h]",
+ "Flow sensor 2 [dL/h]"
+};
+
/* Labels for High Flow Next */
static const char *const label_highflownext_temp_sensors[] = {
"Coolant temp",
@@ -290,6 +324,14 @@ struct aqc_fan_structure_offsets {
u8 speed;
};
+/* Fan structure offsets for Aquaero */
+static struct aqc_fan_structure_offsets aqc_aquaero_fan_structure = {
+ .voltage = AQUAERO_FAN_VOLTAGE_OFFSET,
+ .curr = AQUAERO_FAN_CURRENT_OFFSET,
+ .power = AQUAERO_FAN_POWER_OFFSET,
+ .speed = AQUAERO_FAN_SPEED_OFFSET
+};
+
/* Fan structure offsets for all devices except Aquaero */
static struct aqc_fan_structure_offsets aqc_general_fan_structure = {
.voltage = AQC_FAN_VOLTAGE_OFFSET,
@@ -496,6 +538,7 @@ static umode_t aqc_is_visible(const void *data, enum hwmon_sensor_types type, u3
if (channel < 3)
return 0444;
break;
+ case aquaero:
case quadro:
/* Special case to support flow sensors */
if (channel < priv->num_fans + priv->num_flow_sensors)
@@ -977,6 +1020,42 @@ static int aqc_probe(struct hid_device *hdev, const struct hid_device_id *id)
goto fail_and_stop;
switch (hdev->product) {
+ case USB_PRODUCT_ID_AQUAERO:
+ /*
+ * Aquaero presents itself as three HID devices under the same product ID:
+ * "aquaero keyboard/mouse", "aquaero System Control" and "aquaero Device",
+ * which is the one we want to communicate with. Unlike most other Aquacomputer
+ * devices, Aquaero does not return meaningful data when explicitly requested
+ * using GET_FEATURE_REPORT.
+ *
+ * The difference between "aquaero Device" and the other two is in the collections
+ * they present. The two other devices have the type of the second element in
+ * their respective collections set to 1, while the real device has it set to 0.
+ */
+ if (hdev->collection[1].type != 0) {
+ ret = -ENODEV;
+ goto fail_and_close;
+ }
+
+ priv->kind = aquaero;
+
+ priv->num_fans = AQUAERO_NUM_FANS;
+ priv->fan_sensor_offsets = aquaero_sensor_fan_offsets;
+
+ priv->num_temp_sensors = AQUAERO_NUM_SENSORS;
+ priv->temp_sensor_start_offset = AQUAERO_SENSOR_START;
+ priv->num_virtual_temp_sensors = AQUAERO_NUM_VIRTUAL_SENSORS;
+ priv->virtual_temp_sensor_start_offset = AQUAERO_VIRTUAL_SENSOR_START;
+ priv->num_flow_sensors = AQUAERO_NUM_FLOW_SENSORS;
+ priv->flow_sensors_start_offset = AQUAERO_FLOW_SENSORS_START;
+
+ priv->temp_label = label_temp_sensors;
+ priv->virtual_temp_label = label_virtual_temp_sensors;
+ priv->speed_label = label_aquaero_speeds;
+ priv->power_label = label_fan_power;
+ priv->voltage_label = label_fan_voltage;
+ priv->current_label = label_fan_current;
+ break;
case USB_PRODUCT_ID_D5NEXT:
priv->kind = d5next;
@@ -1100,10 +1179,20 @@ static int aqc_probe(struct hid_device *hdev, const struct hid_device_id *id)
break;
}
- priv->serial_number_start_offset = AQC_SERIAL_START;
- priv->firmware_version_offset = AQC_FIRMWARE_VERSION;
+ switch (priv->kind) {
+ case aquaero:
+ priv->serial_number_start_offset = AQUAERO_SERIAL_START;
+ priv->firmware_version_offset = AQUAERO_FIRMWARE_VERSION;
+
+ priv->fan_structure = &aqc_aquaero_fan_structure;
+ break;
+ default:
+ priv->serial_number_start_offset = AQC_SERIAL_START;
+ priv->firmware_version_offset = AQC_FIRMWARE_VERSION;
- priv->fan_structure = &aqc_general_fan_structure;
+ priv->fan_structure = &aqc_general_fan_structure;
+ break;
+ }
if (priv->buffer_size != 0) {
priv->checksum_start = 0x01;
@@ -1152,6 +1241,7 @@ static void aqc_remove(struct hid_device *hdev)
}
static const struct hid_device_id aqc_table[] = {
+ { HID_USB_DEVICE(USB_VENDOR_ID_AQUACOMPUTER, USB_PRODUCT_ID_AQUAERO) },
{ HID_USB_DEVICE(USB_VENDOR_ID_AQUACOMPUTER, USB_PRODUCT_ID_D5NEXT) },
{ HID_USB_DEVICE(USB_VENDOR_ID_AQUACOMPUTER, USB_PRODUCT_ID_FARBWERK) },
{ HID_USB_DEVICE(USB_VENDOR_ID_AQUACOMPUTER, USB_PRODUCT_ID_FARBWERK360) },
--
2.38.1
^ permalink raw reply related [flat|nested] 8+ messages in thread* Re: [PATCH 6/6] hwmon: (aquacomputer_d5next) Support sensors for Aquacomputer Aquaero
2022-12-18 11:31 ` [PATCH 6/6] hwmon: (aquacomputer_d5next) Support sensors for Aquacomputer Aquaero Leonard Anderweit
@ 2022-12-29 14:20 ` Guenter Roeck
0 siblings, 0 replies; 8+ messages in thread
From: Guenter Roeck @ 2022-12-29 14:20 UTC (permalink / raw)
To: Leonard Anderweit
Cc: linux-hwmon, Aleksa Savic, Jack Doan, Jean Delvare,
Jonathan Corbet, linux-doc, linux-kernel
On Sun, Dec 18, 2022 at 12:31:31PM +0100, Leonard Anderweit wrote:
> Add support for reading sensors of the Aquacomputer Aquaero 5/6 fan
> controllers. These fan controllers supports 4 fans, 8 physical
> temperature sensors, 8 virtual temperature sensors and 2 flow sensors.
> Temperature and flow sensor reading implemented by Aleksa Savic [1] [2]
> [3].
>
> [1] https://github.com/aleksamagicka/aquacomputer_d5next-hwmon/pull/31
> [2] https://github.com/aleksamagicka/aquacomputer_d5next-hwmon/pull/51
> [3] https://github.com/aleksamagicka/aquacomputer_d5next-hwmon/pull/55
>
> Originally-from: Aleksa Savic <savicaleksa83@gmail.com>
> Signed-off-by: Leonard Anderweit <leonard.anderweit@gmail.com>
Series applied to hwmon-next.
Thanks,
Guenter
> ---
> Documentation/hwmon/aquacomputer_d5next.rst | 5 +
> drivers/hwmon/aquacomputer_d5next.c | 108 ++++++++++++++++++--
> 2 files changed, 104 insertions(+), 9 deletions(-)
>
> diff --git a/Documentation/hwmon/aquacomputer_d5next.rst b/Documentation/hwmon/aquacomputer_d5next.rst
> index 637bdbc8fcad..b94ff08080bf 100644
> --- a/Documentation/hwmon/aquacomputer_d5next.rst
> +++ b/Documentation/hwmon/aquacomputer_d5next.rst
> @@ -5,6 +5,7 @@ Kernel driver aquacomputer-d5next
>
> Supported devices:
>
> +* Aquacomputer Aquaero 5/6 fan controllers
> * Aquacomputer D5 Next watercooling pump
> * Aquacomputer Farbwerk RGB controller
> * Aquacomputer Farbwerk 360 RGB controller
> @@ -20,6 +21,10 @@ Description
> This driver exposes hardware sensors of listed Aquacomputer devices, which
> communicate through proprietary USB HID protocols.
>
> +The Aquaero devices expose eight temperature sensors, eight virtual temperature
> +sensors and two flow senors. The fans expose their speed (in RPM), power,
> +voltage and current.
> +
> For the D5 Next pump, available sensors are pump and fan speed, power, voltage
> and current, as well as coolant temperature and eight virtual temp sensors. Also
> available through debugfs are the serial number, firmware version and power-on
> diff --git a/drivers/hwmon/aquacomputer_d5next.c b/drivers/hwmon/aquacomputer_d5next.c
> index d28d7079917a..0fd00cfb86c8 100644
> --- a/drivers/hwmon/aquacomputer_d5next.c
> +++ b/drivers/hwmon/aquacomputer_d5next.c
> @@ -1,7 +1,7 @@
> // SPDX-License-Identifier: GPL-2.0+
> /*
> * hwmon driver for Aquacomputer devices (D5 Next, Farbwerk, Farbwerk 360, Octo,
> - * Quadro, High Flow Next)
> + * Quadro, High Flow Next, Aquaero)
> *
> * Aquacomputer devices send HID reports (with ID 0x01) every second to report
> * sensor values.
> @@ -21,6 +21,7 @@
> #include <asm/unaligned.h>
>
> #define USB_VENDOR_ID_AQUACOMPUTER 0x0c70
> +#define USB_PRODUCT_ID_AQUAERO 0xf001
> #define USB_PRODUCT_ID_FARBWERK 0xf00a
> #define USB_PRODUCT_ID_QUADRO 0xf00d
> #define USB_PRODUCT_ID_D5NEXT 0xf00e
> @@ -28,7 +29,7 @@
> #define USB_PRODUCT_ID_OCTO 0xf011
> #define USB_PRODUCT_ID_HIGHFLOWNEXT 0xf012
>
> -enum kinds { d5next, farbwerk, farbwerk360, octo, quadro, highflownext };
> +enum kinds { d5next, farbwerk, farbwerk360, octo, quadro, highflownext, aquaero };
>
> static const char *const aqc_device_names[] = {
> [d5next] = "d5next",
> @@ -36,7 +37,8 @@ static const char *const aqc_device_names[] = {
> [farbwerk360] = "farbwerk360",
> [octo] = "octo",
> [quadro] = "quadro",
> - [highflownext] = "highflownext"
> + [highflownext] = "highflownext",
> + [aquaero] = "aquaero"
> };
>
> #define DRIVER_NAME "aquacomputer_d5next"
> @@ -57,7 +59,7 @@ static u8 secondary_ctrl_report[] = {
> 0x02, 0x00, 0x00, 0x00, 0x02, 0x00, 0x00, 0x00, 0x00, 0x34, 0xC6
> };
>
> -/* Info, sensor sizes and offsets for all Aquacomputer devices */
> +/* Info, sensor sizes and offsets for most Aquacomputer devices */
> #define AQC_SERIAL_START 0x3
> #define AQC_FIRMWARE_VERSION 0xD
>
> @@ -69,6 +71,24 @@ static u8 secondary_ctrl_report[] = {
> #define AQC_FAN_POWER_OFFSET 0x06
> #define AQC_FAN_SPEED_OFFSET 0x08
>
> +/* Specs of the Aquaero fan controllers */
> +#define AQUAERO_SERIAL_START 0x07
> +#define AQUAERO_FIRMWARE_VERSION 0x0B
> +#define AQUAERO_NUM_FANS 4
> +#define AQUAERO_NUM_SENSORS 8
> +#define AQUAERO_NUM_VIRTUAL_SENSORS 8
> +#define AQUAERO_NUM_FLOW_SENSORS 2
> +
> +/* Sensor report offsets for Aquaero fan controllers */
> +#define AQUAERO_SENSOR_START 0x65
> +#define AQUAERO_VIRTUAL_SENSOR_START 0x85
> +#define AQUAERO_FLOW_SENSORS_START 0xF9
> +#define AQUAERO_FAN_VOLTAGE_OFFSET 0x04
> +#define AQUAERO_FAN_CURRENT_OFFSET 0x06
> +#define AQUAERO_FAN_POWER_OFFSET 0x08
> +#define AQUAERO_FAN_SPEED_OFFSET 0x00
> +static u16 aquaero_sensor_fan_offsets[] = { 0x167, 0x173, 0x17f, 0x18B };
> +
> /* Specs of the D5 Next pump */
> #define D5NEXT_NUM_FANS 2
> #define D5NEXT_NUM_SENSORS 1
> @@ -181,12 +201,16 @@ static const char *const label_d5next_current[] = {
> "Fan current"
> };
>
> -/* Labels for Farbwerk, Farbwerk 360 and Octo and Quadro temperature sensors */
> +/* Labels for Aquaero, Farbwerk, Farbwerk 360 and Octo and Quadro temperature sensors */
> static const char *const label_temp_sensors[] = {
> "Sensor 1",
> "Sensor 2",
> "Sensor 3",
> - "Sensor 4"
> + "Sensor 4",
> + "Sensor 5",
> + "Sensor 6",
> + "Sensor 7",
> + "Sensor 8"
> };
>
> static const char *const label_virtual_temp_sensors[] = {
> @@ -262,6 +286,16 @@ static const char *const label_quadro_speeds[] = {
> "Flow speed [dL/h]"
> };
>
> +/* Labels for Aquaero fan speeds */
> +static const char *const label_aquaero_speeds[] = {
> + "Fan 1 speed",
> + "Fan 2 speed",
> + "Fan 3 speed",
> + "Fan 4 speed",
> + "Flow sensor 1 [dL/h]",
> + "Flow sensor 2 [dL/h]"
> +};
> +
> /* Labels for High Flow Next */
> static const char *const label_highflownext_temp_sensors[] = {
> "Coolant temp",
> @@ -290,6 +324,14 @@ struct aqc_fan_structure_offsets {
> u8 speed;
> };
>
> +/* Fan structure offsets for Aquaero */
> +static struct aqc_fan_structure_offsets aqc_aquaero_fan_structure = {
> + .voltage = AQUAERO_FAN_VOLTAGE_OFFSET,
> + .curr = AQUAERO_FAN_CURRENT_OFFSET,
> + .power = AQUAERO_FAN_POWER_OFFSET,
> + .speed = AQUAERO_FAN_SPEED_OFFSET
> +};
> +
> /* Fan structure offsets for all devices except Aquaero */
> static struct aqc_fan_structure_offsets aqc_general_fan_structure = {
> .voltage = AQC_FAN_VOLTAGE_OFFSET,
> @@ -496,6 +538,7 @@ static umode_t aqc_is_visible(const void *data, enum hwmon_sensor_types type, u3
> if (channel < 3)
> return 0444;
> break;
> + case aquaero:
> case quadro:
> /* Special case to support flow sensors */
> if (channel < priv->num_fans + priv->num_flow_sensors)
> @@ -977,6 +1020,42 @@ static int aqc_probe(struct hid_device *hdev, const struct hid_device_id *id)
> goto fail_and_stop;
>
> switch (hdev->product) {
> + case USB_PRODUCT_ID_AQUAERO:
> + /*
> + * Aquaero presents itself as three HID devices under the same product ID:
> + * "aquaero keyboard/mouse", "aquaero System Control" and "aquaero Device",
> + * which is the one we want to communicate with. Unlike most other Aquacomputer
> + * devices, Aquaero does not return meaningful data when explicitly requested
> + * using GET_FEATURE_REPORT.
> + *
> + * The difference between "aquaero Device" and the other two is in the collections
> + * they present. The two other devices have the type of the second element in
> + * their respective collections set to 1, while the real device has it set to 0.
> + */
> + if (hdev->collection[1].type != 0) {
> + ret = -ENODEV;
> + goto fail_and_close;
> + }
> +
> + priv->kind = aquaero;
> +
> + priv->num_fans = AQUAERO_NUM_FANS;
> + priv->fan_sensor_offsets = aquaero_sensor_fan_offsets;
> +
> + priv->num_temp_sensors = AQUAERO_NUM_SENSORS;
> + priv->temp_sensor_start_offset = AQUAERO_SENSOR_START;
> + priv->num_virtual_temp_sensors = AQUAERO_NUM_VIRTUAL_SENSORS;
> + priv->virtual_temp_sensor_start_offset = AQUAERO_VIRTUAL_SENSOR_START;
> + priv->num_flow_sensors = AQUAERO_NUM_FLOW_SENSORS;
> + priv->flow_sensors_start_offset = AQUAERO_FLOW_SENSORS_START;
> +
> + priv->temp_label = label_temp_sensors;
> + priv->virtual_temp_label = label_virtual_temp_sensors;
> + priv->speed_label = label_aquaero_speeds;
> + priv->power_label = label_fan_power;
> + priv->voltage_label = label_fan_voltage;
> + priv->current_label = label_fan_current;
> + break;
> case USB_PRODUCT_ID_D5NEXT:
> priv->kind = d5next;
>
> @@ -1100,10 +1179,20 @@ static int aqc_probe(struct hid_device *hdev, const struct hid_device_id *id)
> break;
> }
>
> - priv->serial_number_start_offset = AQC_SERIAL_START;
> - priv->firmware_version_offset = AQC_FIRMWARE_VERSION;
> + switch (priv->kind) {
> + case aquaero:
> + priv->serial_number_start_offset = AQUAERO_SERIAL_START;
> + priv->firmware_version_offset = AQUAERO_FIRMWARE_VERSION;
> +
> + priv->fan_structure = &aqc_aquaero_fan_structure;
> + break;
> + default:
> + priv->serial_number_start_offset = AQC_SERIAL_START;
> + priv->firmware_version_offset = AQC_FIRMWARE_VERSION;
>
> - priv->fan_structure = &aqc_general_fan_structure;
> + priv->fan_structure = &aqc_general_fan_structure;
> + break;
> + }
>
> if (priv->buffer_size != 0) {
> priv->checksum_start = 0x01;
> @@ -1152,6 +1241,7 @@ static void aqc_remove(struct hid_device *hdev)
> }
>
> static const struct hid_device_id aqc_table[] = {
> + { HID_USB_DEVICE(USB_VENDOR_ID_AQUACOMPUTER, USB_PRODUCT_ID_AQUAERO) },
> { HID_USB_DEVICE(USB_VENDOR_ID_AQUACOMPUTER, USB_PRODUCT_ID_D5NEXT) },
> { HID_USB_DEVICE(USB_VENDOR_ID_AQUACOMPUTER, USB_PRODUCT_ID_FARBWERK) },
> { HID_USB_DEVICE(USB_VENDOR_ID_AQUACOMPUTER, USB_PRODUCT_ID_FARBWERK360) },
^ permalink raw reply [flat|nested] 8+ messages in thread