From: Philippe Schenker <dev@pschenker.ch>
To: jic23@kernel.org, marcel.ziswiler@toradex.com, stefan@agner.ch
Cc: robh@kernel.org, alexandre.torgue@st.com, shawnguo@kernel.org,
dmitry.torokhov@gmail.com, thierry.reding@gmail.com,
mcoquelin.stm32@gmail.com, digetx@gmail.com,
lee.jones@linaro.org,
Max Krummenacher <max.krummenacher@toradex.com>,
Philippe Schenker <philippe.schenker@toradex.com>,
Jonathan Cameron <Jonathan.Cameron@huawei.com>,
devicetree@vger.kernel.org, linux-iio@vger.kernel.org,
Hartmut Knaack <knaack.h@gmx.de>,
linux-input@vger.kernel.org, linux-kernel@vger.kernel.org,
Rob Herring <robh+dt@kernel.org>,
Mark Rutland <mark.rutland@arm.com>,
Peter Meerwald-Stadler <pmeerw@pmeerw.net>,
linux-stm32@st-md-mailman.stormreply.com,
linux-arm-kernel@lists.infradead.org,
Lars-Peter Clausen <lars@metafoo.de>
Subject: [PATCH v6 6/8] iio: adc: add STMPE ADC devicetree bindings
Date: Wed, 9 Jan 2019 14:42:05 +0100 [thread overview]
Message-ID: <20190109134208.5660-7-dev@pschenker.ch> (raw)
In-Reply-To: <20190109134208.5660-1-dev@pschenker.ch>
From: Stefan Agner <stefan@agner.ch>
This adds the devicetree bindings for the STMPE ADC. This also corrects
a typo in st,sample-time it is rather "6 -> 124 clocks" according
to the datasheet and not 144.
We need to use the naming stmpe_adc in devicetree because this is given
by the mfd device.
Signed-off-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Max Krummenacher <max.krummenacher@toradex.com>
Signed-off-by: Philippe Schenker <philippe.schenker@toradex.com>
Reviewed-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Reviewed-by: Rob Herring <robh@kernel.org>
---
Changes in v6:
- Added Rob's Reviewed-by
Changes in v5:
- Made a one column list
- Cleared note about precedence
- Changed example to a full STMPE811 device with MFD, touchscreen, and the new
stmpe_adc driver.
- Added Jonathan Cameron's Reviewed-by
Changes in v4:
- Put reformatting in a separate precursor patch.
Changes in v3:
- Reformatted documentation for touchscreen to use tabs and have a better
overview of the settings.
- Added note which adc-settings will take precedence.
- changed typo in sample-time setting from 144 clocks to 124 clocks, as stated
in the datasheet.
Changes in v2:
- Moved the bindings for ADC to the overlying mfd.
- Reformatted for better readability
.../devicetree/bindings/iio/adc/stmpe-adc.txt | 21 +++++
.../bindings/input/touchscreen/stmpe.txt | 88 +++++++++++++------
.../devicetree/bindings/mfd/stmpe.txt | 14 +++
3 files changed, 98 insertions(+), 25 deletions(-)
create mode 100644 Documentation/devicetree/bindings/iio/adc/stmpe-adc.txt
diff --git a/Documentation/devicetree/bindings/iio/adc/stmpe-adc.txt b/Documentation/devicetree/bindings/iio/adc/stmpe-adc.txt
new file mode 100644
index 000000000000..480e66422625
--- /dev/null
+++ b/Documentation/devicetree/bindings/iio/adc/stmpe-adc.txt
@@ -0,0 +1,21 @@
+STMPE ADC driver
+----------------
+
+Required properties:
+ - compatible: "st,stmpe-adc"
+
+Optional properties:
+Note that the ADC is shared with the STMPE touchscreen. ADC related settings
+have to be done in the mfd.
+- st,norequest-mask: bitmask specifying which ADC channels should _not_ be
+ requestable due to different usage (e.g. touch)
+
+Node name must be stmpe_adc and should be child node of stmpe node to
+which it belongs.
+
+Example:
+
+ stmpe_adc {
+ compatible = "st,stmpe-adc";
+ st,norequest-mask = <0x0F>; /* dont use ADC CH3-0 */
+ };
diff --git a/Documentation/devicetree/bindings/input/touchscreen/stmpe.txt b/Documentation/devicetree/bindings/input/touchscreen/stmpe.txt
index bf66a55a7de5..c549924603d2 100644
--- a/Documentation/devicetree/bindings/input/touchscreen/stmpe.txt
+++ b/Documentation/devicetree/bindings/input/touchscreen/stmpe.txt
@@ -5,24 +5,6 @@ Required properties:
- compatible: "st,stmpe-ts"
Optional properties:
-- st,sample-time : ADC conversion time in number of clock.
- 0 -> 36 clocks
- 1 -> 44 clocks
- 2 -> 56 clocks
- 3 -> 64 clocks
- 4 -> 80 clocks (recommended)
- 5 -> 96 clocks
- 6 -> 144 clocks
-- st,mod-12b : ADC Bit mode
- 0 -> 10bit ADC
- 1 -> 12bit ADC
-- st,ref-sel : ADC reference source
- 0 -> internal
- 1 -> external
-- st,adc-freq : ADC Clock speed
- 0 -> 1.625 MHz
- 1 -> 3.25 MHz
- 2 || 3 -> 6.5 MHz
- st,ave-ctrl : Sample average control
0 -> 1 sample
1 -> 2 samples
@@ -52,20 +34,76 @@ Optional properties:
0 -> 20 mA (typical 35mA max)
1 -> 50 mA (typical 80 mA max)
+Optional properties common with MFD (deprecated):
+ - st,sample-time : ADC conversion time in number of clock.
+ 0 -> 36 clocks
+ 1 -> 44 clocks
+ 2 -> 56 clocks
+ 3 -> 64 clocks
+ 4 -> 80 clocks (recommended)
+ 5 -> 96 clocks
+ 6 -> 124 clocks
+ - st,mod-12b : ADC Bit mode
+ 0 -> 10bit ADC
+ 1 -> 12bit ADC
+ - st,ref-sel : ADC reference source
+ 0 -> internal
+ 1 -> external
+ - st,adc-freq : ADC Clock speed
+ 0 -> 1.625 MHz
+ 1 -> 3.25 MHz
+ 2 || 3 -> 6.5 MHz
+
Node name must be stmpe_touchscreen and should be child node of stmpe node to
which it belongs.
+Note that common ADC settings of stmpe_touchscreen (child) will take precedence
+over the settings done in MFD.
+
Example:
+stmpe811@41 {
+ compatible = "st,stmpe811";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_touch_int>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <0x41>;
+ interrupts = <10 IRQ_TYPE_LEVEL_LOW>;
+ interrupt-parent = <&gpio4>;
+ interrupt-controller;
+ id = <0>;
+ blocks = <0x5>;
+ irq-trigger = <0x1>;
+ /* Common ADC settings */
+ /* 3.25 MHz ADC clock speed */
+ st,adc-freq = <1>;
+ /* 12-bit ADC */
+ st,mod-12b = <1>;
+ /* internal ADC reference */
+ st,ref-sel = <0>;
+ /* ADC converstion time: 80 clocks */
+ st,sample-time = <4>;
+
stmpe_touchscreen {
compatible = "st,stmpe-ts";
- st,sample-time = <4>;
- st,mod-12b = <1>;
- st,ref-sel = <0>;
- st,adc-freq = <1>;
- st,ave-ctrl = <1>;
- st,touch-det-delay = <2>;
- st,settling = <2>;
+ reg = <0>;
+ /* 8 sample average control */
+ st,ave-ctrl = <3>;
+ /* 5 ms touch detect interrupt delay */
+ st,touch-det-delay = <5>;
+ /* 1 ms panel driver settling time */
+ st,settling = <3>;
+ /* 7 length fractional part in z */
st,fraction-z = <7>;
+ /*
+ * 50 mA typical 80 mA max touchscreen drivers
+ * current limit value
+ */
st,i-drive = <1>;
};
+ stmpe_adc {
+ compatible = "st,stmpe-adc";
+ st,norequest-mask = <0x0F>;
+ };
+};
diff --git a/Documentation/devicetree/bindings/mfd/stmpe.txt b/Documentation/devicetree/bindings/mfd/stmpe.txt
index a46e7177195d..d4408a417193 100644
--- a/Documentation/devicetree/bindings/mfd/stmpe.txt
+++ b/Documentation/devicetree/bindings/mfd/stmpe.txt
@@ -14,6 +14,20 @@ Optional properties:
- st,autosleep-timeout : Valid entries (ms); 4, 16, 32, 64, 128, 256, 512 and 1024
- irq-gpio : If present, which GPIO to use for event IRQ
+Optional properties for devices with touch and ADC (STMPE811|STMPE610):
+ - st,sample-time : ADC conversion time in number of clock.
+ 0 -> 36 clocks 4 -> 80 clocks (recommended)
+ 1 -> 44 clocks 5 -> 96 clocks
+ 2 -> 56 clocks 6 -> 124 clocks
+ 3 -> 64 clocks
+ - st,mod-12b : ADC Bit mode
+ 0 -> 10bit ADC 1 -> 12bit ADC
+ - st,ref-sel : ADC reference source
+ 0 -> internal 1 -> external
+ - st,adc-freq : ADC Clock speed
+ 0 -> 1.625 MHz 2 || 3 -> 6.5 MHz
+ 1 -> 3.25 MHz
+
Example:
stmpe1601: stmpe1601@40 {
--
2.20.1
prev parent reply other threads:[~2019-01-09 13:43 UTC|newest]
Thread overview: 3+ messages / expand[flat|nested] mbox.gz Atom feed top
2019-01-09 13:41 [PATCH v6 0/8] Adding support for STMPE811 ADC Philippe Schenker
2019-01-09 13:42 ` [PATCH v6 5/8] iio: adc: add STMPE ADC driver using IIO framework Philippe Schenker
2019-01-09 13:42 ` Philippe Schenker [this message]
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20190109134208.5660-7-dev@pschenker.ch \
--to=dev@pschenker.ch \
--cc=Jonathan.Cameron@huawei.com \
--cc=alexandre.torgue@st.com \
--cc=devicetree@vger.kernel.org \
--cc=digetx@gmail.com \
--cc=dmitry.torokhov@gmail.com \
--cc=jic23@kernel.org \
--cc=knaack.h@gmx.de \
--cc=lars@metafoo.de \
--cc=lee.jones@linaro.org \
--cc=linux-arm-kernel@lists.infradead.org \
--cc=linux-iio@vger.kernel.org \
--cc=linux-input@vger.kernel.org \
--cc=linux-kernel@vger.kernel.org \
--cc=linux-stm32@st-md-mailman.stormreply.com \
--cc=marcel.ziswiler@toradex.com \
--cc=mark.rutland@arm.com \
--cc=max.krummenacher@toradex.com \
--cc=mcoquelin.stm32@gmail.com \
--cc=philippe.schenker@toradex.com \
--cc=pmeerw@pmeerw.net \
--cc=robh+dt@kernel.org \
--cc=robh@kernel.org \
--cc=shawnguo@kernel.org \
--cc=stefan@agner.ch \
--cc=thierry.reding@gmail.com \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).