From: Jonathan Cameron <jic23@kernel.org>
To: Matt Ranostay <matt.ranostay@konsulko.com>
Cc: linux-iio@vger.kernel.org
Subject: Re: [PATCH v4 2/3] iio: chemical: atlas-sensor: add DO-SM module support
Date: Sat, 8 Feb 2020 16:41:35 +0000 [thread overview]
Message-ID: <20200208164135.3e4f606c@archlinux> (raw)
In-Reply-To: <20200206061332.20427-3-matt.ranostay@konsulko.com>
On Wed, 5 Feb 2020 22:13:31 -0800
Matt Ranostay <matt.ranostay@konsulko.com> wrote:
> Atlas Scientific DO-SM OEM sensor reads disolved oxygen in
> a solution. This is reported back as mg/L which maps direc
> to ppm and so the IIO_CONCENTRATION channel type can be used.
>
> Signed-off-by: Matt Ranostay <matt.ranostay@konsulko.com>
Hi Matt,
This looks good to me. Will pick up once we've resolved the other
bits in the series.
Also want to give time for Rob to take a look a the yaml.
Thanks,
Jonathan
> ---
> drivers/iio/chemical/atlas-sensor.c | 64 +++++++++++++++++++++++++++--
> 1 file changed, 60 insertions(+), 4 deletions(-)
>
> diff --git a/drivers/iio/chemical/atlas-sensor.c b/drivers/iio/chemical/atlas-sensor.c
> index 2e34c82cb65d..919d408869be 100644
> --- a/drivers/iio/chemical/atlas-sensor.c
> +++ b/drivers/iio/chemical/atlas-sensor.c
> @@ -48,6 +48,11 @@
> #define ATLAS_REG_EC_CALIB_STATUS_LOW BIT(2)
> #define ATLAS_REG_EC_CALIB_STATUS_HIGH BIT(3)
>
> +#define ATLAS_REG_DO_CALIB_STATUS 0x09
> +#define ATLAS_REG_DO_CALIB_STATUS_MASK 0x03
> +#define ATLAS_REG_DO_CALIB_STATUS_PRESSURE BIT(0)
> +#define ATLAS_REG_DO_CALIB_STATUS_DO BIT(1)
> +
> #define ATLAS_REG_PH_TEMP_DATA 0x0e
> #define ATLAS_REG_PH_DATA 0x16
>
> @@ -60,14 +65,19 @@
> #define ATLAS_REG_ORP_CALIB_STATUS 0x0d
> #define ATLAS_REG_ORP_DATA 0x0e
>
> +#define ATLAS_REG_DO_TEMP_DATA 0x12
> +#define ATLAS_REG_DO_DATA 0x22
> +
> #define ATLAS_PH_INT_TIME_IN_MS 450
> #define ATLAS_EC_INT_TIME_IN_MS 650
> #define ATLAS_ORP_INT_TIME_IN_MS 450
> +#define ATLAS_DO_INT_TIME_IN_MS 450
>
> enum {
> ATLAS_PH_SM,
> ATLAS_EC_SM,
> ATLAS_ORP_SM,
> + ATLAS_DO_SM,
> };
>
> struct atlas_data {
> @@ -121,7 +131,7 @@ static const struct iio_chan_spec atlas_ph_channels[] = {
> },
> };
>
> -#define ATLAS_EC_CHANNEL(_idx, _addr) \
> +#define ATLAS_CONCENTRATION_CHANNEL(_idx, _addr) \
> {\
> .type = IIO_CONCENTRATION, \
> .indexed = 1, \
> @@ -152,8 +162,8 @@ static const struct iio_chan_spec atlas_ec_channels[] = {
> .endianness = IIO_BE,
> },
> },
> - ATLAS_EC_CHANNEL(0, ATLAS_REG_TDS_DATA),
> - ATLAS_EC_CHANNEL(1, ATLAS_REG_PSS_DATA),
> + ATLAS_CONCENTRATION_CHANNEL(0, ATLAS_REG_TDS_DATA),
> + ATLAS_CONCENTRATION_CHANNEL(1, ATLAS_REG_PSS_DATA),
> IIO_CHAN_SOFT_TIMESTAMP(3),
> {
> .type = IIO_TEMP,
> @@ -182,6 +192,19 @@ static const struct iio_chan_spec atlas_orp_channels[] = {
> IIO_CHAN_SOFT_TIMESTAMP(1),
> };
>
> +static const struct iio_chan_spec atlas_do_channels[] = {
> + ATLAS_CONCENTRATION_CHANNEL(0, ATLAS_REG_DO_DATA),
> + IIO_CHAN_SOFT_TIMESTAMP(1),
> + {
> + .type = IIO_TEMP,
> + .address = ATLAS_REG_DO_TEMP_DATA,
> + .info_mask_separate =
> + BIT(IIO_CHAN_INFO_RAW) | BIT(IIO_CHAN_INFO_SCALE),
> + .output = 1,
> + .scan_index = -1
> + },
> +};
> +
> static int atlas_check_ph_calibration(struct atlas_data *data)
> {
> struct device *dev = &data->client->dev;
> @@ -262,7 +285,31 @@ static int atlas_check_orp_calibration(struct atlas_data *data)
> dev_warn(dev, "device has not been calibrated\n");
>
> return 0;
> -};
> +}
Unrelated change so really should have been in a separate patch, but meh
it's trivial so I won't fuss too much about it being here ;)
> +
> +static int atlas_check_do_calibration(struct atlas_data *data)
> +{
> + struct device *dev = &data->client->dev;
> + int ret;
> + unsigned int val;
> +
> + ret = regmap_read(data->regmap, ATLAS_REG_DO_CALIB_STATUS, &val);
> + if (ret)
> + return ret;
> +
> + if (!(val & ATLAS_REG_DO_CALIB_STATUS_MASK)) {
> + dev_warn(dev, "device has not been calibrated\n");
> + return 0;
> + }
> +
> + if (!(val & ATLAS_REG_DO_CALIB_STATUS_PRESSURE))
> + dev_warn(dev, "device missing atmospheric pressure calibration\n");
> +
> + if (!(val & ATLAS_REG_DO_CALIB_STATUS_DO))
> + dev_warn(dev, "device missing dissolved oxygen calibration\n");
> +
> + return 0;
> +}
>
> struct atlas_device {
> const struct iio_chan_spec *channels;
> @@ -295,6 +342,13 @@ static struct atlas_device atlas_devices[] = {
> .calibration = &atlas_check_orp_calibration,
> .delay = ATLAS_ORP_INT_TIME_IN_MS,
> },
> + [ATLAS_DO_SM] = {
> + .channels = atlas_do_channels,
> + .num_channels = 3,
> + .data_reg = ATLAS_REG_DO_DATA,
> + .calibration = &atlas_check_do_calibration,
> + .delay = ATLAS_DO_INT_TIME_IN_MS,
> + },
> };
>
> static int atlas_set_powermode(struct atlas_data *data, int on)
> @@ -507,6 +561,7 @@ static const struct i2c_device_id atlas_id[] = {
> { "atlas-ph-sm", ATLAS_PH_SM},
> { "atlas-ec-sm", ATLAS_EC_SM},
> { "atlas-orp-sm", ATLAS_ORP_SM},
> + { "atlas-do-sm", ATLAS_DO_SM},
> {}
> };
> MODULE_DEVICE_TABLE(i2c, atlas_id);
> @@ -515,6 +570,7 @@ static const struct of_device_id atlas_dt_ids[] = {
> { .compatible = "atlas,ph-sm", .data = (void *)ATLAS_PH_SM, },
> { .compatible = "atlas,ec-sm", .data = (void *)ATLAS_EC_SM, },
> { .compatible = "atlas,orp-sm", .data = (void *)ATLAS_ORP_SM, },
> + { .compatible = "atlas,do-sm", .data = (void *)ATLAS_DO_SM, },
> { }
> };
> MODULE_DEVICE_TABLE(of, atlas_dt_ids);
next prev parent reply other threads:[~2020-02-08 16:41 UTC|newest]
Thread overview: 13+ messages / expand[flat|nested] mbox.gz Atom feed top
2020-02-06 6:13 [PATCH v4 0/3] iio: chemical: atlas-sensor: add DO support Matt Ranostay
2020-02-06 6:13 ` [PATCH v4 1/3] iio: chemical: atlas-sensor: allow probe without interrupt line Matt Ranostay
2020-02-07 0:53 ` Jeremy Fertic
2020-02-07 4:59 ` Matt Ranostay
2020-02-08 16:39 ` Jonathan Cameron
2020-02-09 2:12 ` Matt Ranostay
2020-02-09 2:16 ` Matt Ranostay
2020-02-14 13:27 ` Jonathan Cameron
2020-02-06 6:13 ` [PATCH v4 2/3] iio: chemical: atlas-sensor: add DO-SM module support Matt Ranostay
2020-02-08 16:41 ` Jonathan Cameron [this message]
2020-02-06 6:13 ` [PATCH v4 3/3] dt-bindings: iio: chemical: consolidate atlas-sensor docs Matt Ranostay
2020-02-06 21:52 ` Rob Herring
2020-02-08 16:34 ` Jonathan Cameron
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20200208164135.3e4f606c@archlinux \
--to=jic23@kernel.org \
--cc=linux-iio@vger.kernel.org \
--cc=matt.ranostay@konsulko.com \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).