From: Jonathan Cameron <jic23@kernel.org>
To: <tomislav.denis@avl.com>
Cc: <linux-iio@vger.kernel.org>, <devicetree@vger.kernel.org>
Subject: Re: [PATCH v2 2/2] bindings: iio: adc: Add documentation for ADS131E0x ADC driver
Date: Sat, 9 Jan 2021 20:40:02 +0000 [thread overview]
Message-ID: <20210109204002.5d3c3ff2@archlinux> (raw)
In-Reply-To: <20210105110839.5436-3-tomislav.denis@avl.com>
On Tue, 5 Jan 2021 12:08:39 +0100
<tomislav.denis@avl.com> wrote:
> From: Tomislav Denis <tomislav.denis@avl.com>
>
> Add a device tree binding documentation for Texas Instruments
> ADS131E0x ADC family driver.
>
> Signed-off-by: Tomislav Denis <tomislav.denis@avl.com>
One trivial thing inline. If that is all that comes up I can fix
whilst applying.
Thanks,
Jonathan
> ---
> .../devicetree/bindings/iio/adc/ti,ads131e08.yaml | 181 +++++++++++++++++++++
> MAINTAINERS | 1 +
> 2 files changed, 182 insertions(+)
> create mode 100644 Documentation/devicetree/bindings/iio/adc/ti,ads131e08.yaml
>
> diff --git a/Documentation/devicetree/bindings/iio/adc/ti,ads131e08.yaml b/Documentation/devicetree/bindings/iio/adc/ti,ads131e08.yaml
> new file mode 100644
> index 0000000..c84eadd2
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/iio/adc/ti,ads131e08.yaml
> @@ -0,0 +1,181 @@
> +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
> +%YAML 1.2
> +---
> +$id: http://devicetree.org/schemas/iio/adc/ti,ads131e08.yaml#
> +$schema: http://devicetree.org/meta-schemas/core.yaml#
> +
> +title: Texas Instruments ADS131E0x 4-, 6- and 8-Channel ADCs
> +
> +maintainers:
> + - Tomislav Denis <tomislav.denis@avl.com>
> +
> +description: |
> + The ADS131E0x are a family of multichannel, simultaneous sampling,
> + 24-bit, delta-sigma, analog-to-digital converters (ADCs) with a
> + built-in programmable gain amplifier (PGA), internal reference
> + and an onboard oscillator.
> + The communication with ADC chip is via the SPI bus (mode 1).
> +
> + https://www.ti.com/lit/ds/symlink/ads131e08.pdf
> +
> +properties:
> + compatible:
> + enum:
> + - ti,ads131e04
> + - ti,ads131e06
> + - ti,ads131e08
> +
> + reg:
> + maxItems: 1
> +
> + spi-max-frequency: true
> +
> + spi-cpha: true
> +
> + clocks:
> + description: |
> + Device tree identifier to the clock source (2.048 MHz).
> + Note: clock source is selected using CLKSEL pin.
> + maxItems: 1
> +
> + clock-names:
> + items:
> + - const: adc-clk
> +
> + interrupts:
> + description: |
> + IRQ line for the ADC data ready.
> + maxItems: 1
> +
> + vref-supply:
> + description: |
> + Optional external voltage reference. If not supplied, internal voltage
> + reference is used.
> +
> + ti,vref-internal:
> + description: |
> + Select the internal voltage reference value.
> + 0: 2.4V
> + 1: 4.0V
> + If this field is left empty, 2.4V is selected.
> + Note: internal voltage reference is used only if vref-supply is not supplied.
> + $ref: /schemas/types.yaml#/definitions/uint32
> + enum: [0, 1]
> + default: 0
> +
> + '#address-cells':
> + const: 1
> +
> + '#size-cells':
> + const: 0
> +
> +required:
> + - compatible
> + - reg
> + - spi-cpha
> + - clocks
> + - clock-names
> + - interrupts
> +
> +patternProperties:
> + "^channel@([0-7])$":
> + $ref: "adc.yaml"
> + type: object
> + description: |
> + Represents the external channels which are connected to the ADC.
> +
> + properties:
> + reg:
> + description: |
> + The channel number.
> + Up to 4 channels, numbered from 0 to 3 for ti,ads131e04.
> + Up to 6 channels, numbered from 0 to 5 for ti,ads131e06.
> + Up to 8 channels, numbered from 0 to 7 for ti,ads131e08.
> + items:
> + minimum: 0
> + maximum: 8
7?
> +
> + ti,gain:
> + description: |
> + The PGA gain value for the channel.
> + If this field is left empty, PGA gain 1 is used.
> + $ref: /schemas/types.yaml#/definitions/uint32
> + enum: [1, 2, 4, 8, 12]
> + default: 1
> +
> + ti,mux:
> + description: |
> + Channel input selection(muliplexer).
> + 0: Normal input.
> + 1: Input shorted to (VREFP + VREFN) / 2 (for offset or noise measurements).
> + 3: MVDD (for supply measurement)
> + 4: Temperature sensor
> + If this field is left empty, normal input is selected.
> + $ref: /schemas/types.yaml#/definitions/uint32
> + enum: [0, 1, 3, 4]
> + default: 0
> +
> + required:
> + - reg
> +
> + additionalProperties: false
> +
> +additionalProperties: false
> +
> +examples:
> + - |
> + #include <dt-bindings/interrupt-controller/irq.h>
> +
> + spi {
> + #address-cells = <1>;
> + #size-cells = <0>;
> +
> + adc@0 {
> + compatible = "ti,ads131e08";
> + reg = <0>;
> + spi-max-frequency = <1000000>;
> + spi-cpha;
> + clocks = <&clk2048k>;
> + clock-names = "adc-clk";
> + interrupt-parent = <&gpio5>;
> + interrupts = <28 IRQ_TYPE_EDGE_FALLING>;
> + vref-supply = <&adc_vref>;
> +
> + #address-cells = <1>;
> + #size-cells = <0>;
> +
> + channel@0 {
> + reg = <0>;
> + };
> +
> + channel@1 {
> + reg = <1>;
> + };
> +
> + channel@2 {
> + reg = <2>;
> + ti,gain = <2>;
> + };
> +
> + channel@3 {
> + reg = <3>;
> + };
> +
> + channel@4 {
> + reg = <4>;
> + };
> +
> + channel@5 {
> + reg = <5>;
> + };
> +
> + channel@6 {
> + reg = <6>;
> + };
> +
> + channel@7 {
> + reg = <7>;
> + ti,mux = <4>;
> + };
> + };
> + };
> diff --git a/MAINTAINERS b/MAINTAINERS
> index 167aabf..f6c5e47 100644
> --- a/MAINTAINERS
> +++ b/MAINTAINERS
> @@ -17371,6 +17371,7 @@ TI ADS131E0X ADC SERIES DRIVER
> M: Tomislav Denis <tomislav.denis@avl.com>
> L: linux-iio@vger.kernel.org
> S: Maintained
> +F: Documentation/devicetree/bindings/iio/adc/ti,ads131e08.yaml
> F: drivers/iio/adc/ti-ads131e08.c
>
> TI AM437X VPFE DRIVER
next prev parent reply other threads:[~2021-01-09 20:41 UTC|newest]
Thread overview: 6+ messages / expand[flat|nested] mbox.gz Atom feed top
2021-01-05 11:08 [PATCH v2 0/2] Add support for ADS131E0x ADC family tomislav.denis
2021-01-05 11:08 ` [PATCH v2 1/2] iio: adc: Add driver for Texas Instruments " tomislav.denis
2021-01-09 21:37 ` Jonathan Cameron
2021-01-05 11:08 ` [PATCH v2 2/2] bindings: iio: adc: Add documentation for ADS131E0x ADC driver tomislav.denis
2021-01-09 20:40 ` Jonathan Cameron [this message]
2021-01-11 23:38 ` Rob Herring
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20210109204002.5d3c3ff2@archlinux \
--to=jic23@kernel.org \
--cc=devicetree@vger.kernel.org \
--cc=linux-iio@vger.kernel.org \
--cc=tomislav.denis@avl.com \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).