From: <tomislav.denis@avl.com>
To: <jic23@kernel.org>
Cc: <linux-iio@vger.kernel.org>, <devicetree@vger.kernel.org>,
<tomislav.denis@avl.com>
Subject: [PATCH v4 2/2] bindings: iio: adc: Add documentation for ADS131E0x ADC driver
Date: Tue, 2 Feb 2021 09:41:07 +0100 [thread overview]
Message-ID: <20210202084107.3260-3-tomislav.denis@avl.com> (raw)
In-Reply-To: <20210202084107.3260-1-tomislav.denis@avl.com>
From: Tomislav Denis <tomislav.denis@avl.com>
Add a device tree binding documentation for Texas Instruments
ADS131E0x ADC family driver.
Signed-off-by: Tomislav Denis <tomislav.denis@avl.com>
Reviewed-by: Rob Herring <robh@kernel.org>
---
.../devicetree/bindings/iio/adc/ti,ads131e08.yaml | 181 +++++++++++++++++++++
MAINTAINERS | 1 +
2 files changed, 182 insertions(+)
create mode 100644 Documentation/devicetree/bindings/iio/adc/ti,ads131e08.yaml
diff --git a/Documentation/devicetree/bindings/iio/adc/ti,ads131e08.yaml b/Documentation/devicetree/bindings/iio/adc/ti,ads131e08.yaml
new file mode 100644
index 0000000..e0670e3
--- /dev/null
+++ b/Documentation/devicetree/bindings/iio/adc/ti,ads131e08.yaml
@@ -0,0 +1,181 @@
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/iio/adc/ti,ads131e08.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Texas Instruments ADS131E0x 4-, 6- and 8-Channel ADCs
+
+maintainers:
+ - Tomislav Denis <tomislav.denis@avl.com>
+
+description: |
+ The ADS131E0x are a family of multichannel, simultaneous sampling,
+ 24-bit, delta-sigma, analog-to-digital converters (ADCs) with a
+ built-in programmable gain amplifier (PGA), internal reference
+ and an onboard oscillator.
+ The communication with ADC chip is via the SPI bus (mode 1).
+
+ https://www.ti.com/lit/ds/symlink/ads131e08.pdf
+
+properties:
+ compatible:
+ enum:
+ - ti,ads131e04
+ - ti,ads131e06
+ - ti,ads131e08
+
+ reg:
+ maxItems: 1
+
+ spi-max-frequency: true
+
+ spi-cpha: true
+
+ clocks:
+ description: |
+ Device tree identifier to the clock source (2.048 MHz).
+ Note: clock source is selected using CLKSEL pin.
+ maxItems: 1
+
+ clock-names:
+ items:
+ - const: adc-clk
+
+ interrupts:
+ description: |
+ IRQ line for the ADC data ready.
+ maxItems: 1
+
+ vref-supply:
+ description: |
+ Optional external voltage reference. If not supplied, internal voltage
+ reference is used.
+
+ ti,vref-internal:
+ description: |
+ Select the internal voltage reference value.
+ 0: 2.4V
+ 1: 4.0V
+ If this field is left empty, 2.4V is selected.
+ Note: internal voltage reference is used only if vref-supply is not supplied.
+ $ref: /schemas/types.yaml#/definitions/uint32
+ enum: [0, 1]
+ default: 0
+
+ '#address-cells':
+ const: 1
+
+ '#size-cells':
+ const: 0
+
+required:
+ - compatible
+ - reg
+ - spi-cpha
+ - clocks
+ - clock-names
+ - interrupts
+
+patternProperties:
+ "^channel@([0-7])$":
+ $ref: "adc.yaml"
+ type: object
+ description: |
+ Represents the external channels which are connected to the ADC.
+
+ properties:
+ reg:
+ description: |
+ The channel number.
+ Up to 4 channels, numbered from 0 to 3 for ti,ads131e04.
+ Up to 6 channels, numbered from 0 to 5 for ti,ads131e06.
+ Up to 8 channels, numbered from 0 to 7 for ti,ads131e08.
+ items:
+ minimum: 0
+ maximum: 7
+
+ ti,gain:
+ description: |
+ The PGA gain value for the channel.
+ If this field is left empty, PGA gain 1 is used.
+ $ref: /schemas/types.yaml#/definitions/uint32
+ enum: [1, 2, 4, 8, 12]
+ default: 1
+
+ ti,mux:
+ description: |
+ Channel input selection(muliplexer).
+ 0: Normal input.
+ 1: Input shorted to (VREFP + VREFN) / 2 (for offset or noise measurements).
+ 3: MVDD (for supply measurement)
+ 4: Temperature sensor
+ If this field is left empty, normal input is selected.
+ $ref: /schemas/types.yaml#/definitions/uint32
+ enum: [0, 1, 3, 4]
+ default: 0
+
+ required:
+ - reg
+
+ additionalProperties: false
+
+additionalProperties: false
+
+examples:
+ - |
+ #include <dt-bindings/interrupt-controller/irq.h>
+
+ spi {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ adc@0 {
+ compatible = "ti,ads131e08";
+ reg = <0>;
+ spi-max-frequency = <1000000>;
+ spi-cpha;
+ clocks = <&clk2048k>;
+ clock-names = "adc-clk";
+ interrupt-parent = <&gpio5>;
+ interrupts = <28 IRQ_TYPE_EDGE_FALLING>;
+ vref-supply = <&adc_vref>;
+
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ channel@0 {
+ reg = <0>;
+ };
+
+ channel@1 {
+ reg = <1>;
+ };
+
+ channel@2 {
+ reg = <2>;
+ ti,gain = <2>;
+ };
+
+ channel@3 {
+ reg = <3>;
+ };
+
+ channel@4 {
+ reg = <4>;
+ };
+
+ channel@5 {
+ reg = <5>;
+ };
+
+ channel@6 {
+ reg = <6>;
+ };
+
+ channel@7 {
+ reg = <7>;
+ ti,mux = <4>;
+ };
+ };
+ };
diff --git a/MAINTAINERS b/MAINTAINERS
index 167aabf..f6c5e47 100644
--- a/MAINTAINERS
+++ b/MAINTAINERS
@@ -17371,6 +17371,7 @@ TI ADS131E0X ADC SERIES DRIVER
M: Tomislav Denis <tomislav.denis@avl.com>
L: linux-iio@vger.kernel.org
S: Maintained
+F: Documentation/devicetree/bindings/iio/adc/ti,ads131e08.yaml
F: drivers/iio/adc/ti-ads131e08.c
TI AM437X VPFE DRIVER
--
2.7.4
prev parent reply other threads:[~2021-02-02 8:42 UTC|newest]
Thread overview: 4+ messages / expand[flat|nested] mbox.gz Atom feed top
2021-02-02 8:41 [PATCH v4 0/2] Add support for ADS131E0x ADC family tomislav.denis
2021-02-02 8:41 ` [PATCH v4 1/2] iio: adc: Add driver for Texas Instruments " tomislav.denis
2021-02-06 16:54 ` Jonathan Cameron
2021-02-02 8:41 ` tomislav.denis [this message]
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20210202084107.3260-3-tomislav.denis@avl.com \
--to=tomislav.denis@avl.com \
--cc=devicetree@vger.kernel.org \
--cc=jic23@kernel.org \
--cc=linux-iio@vger.kernel.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).