From: "Théo Borém Fabris" <theobf@usp.br>
To: Alexandru Ardelean <ardeleanalex@gmail.com>
Cc: Jonathan Cameron <jic23@kernel.org>,
Lars-Peter Clausen <lars@metafoo.de>,
linux-iio <linux-iio@vger.kernel.org>,
LKML <linux-kernel@vger.kernel.org>
Subject: Re: [PATCH] iio: dac: max5821: convert device register to device managed function
Date: Tue, 20 Jul 2021 21:11:20 -0300 [thread overview]
Message-ID: <CAD5vTa_cR0da4qZ2JTB7G-QgZrSeZr3e8fp92S6WGMaCoUr15g@mail.gmail.com> (raw)
In-Reply-To: <CA+U=DsrU5iPBRexdUK3fx-PG3CbSoKouGWENVLJ5+h8L5-y_Og@mail.gmail.com>
Em ter., 20 de jul. de 2021 às 04:22, Alexandru Ardelean
<ardeleanalex@gmail.com> escreveu:
>
> On Mon, Jul 19, 2021 at 6:25 PM Théo Borém Fabris <theobf@usp.br> wrote:
> >
> > Hi, Alexandru.
> >
> > Em seg., 19 de jul. de 2021 às 04:33, Alexandru Ardelean
> > <ardeleanalex@gmail.com> escreveu:
> > >
> > > On Sun, Jul 18, 2021 at 11:42 PM Théo Borém Fabris <theobf@usp.br> wrote:
> > > >
> > > > Add a device managed hook, via devm_add_action_or_reset() and
> > > > max5821_regulator_disable(), to disable voltage regulator on device
> > > > detach.
> > > > Replace iio_device_register() by devm_iio_device_register() and remove
> > > > the max5821_remove() function used to unregister the device and disable the
> > > > voltage regulator.
> > > > Remove i2c_set_clientdata() from the probe function, since
> > > > i2c_get_clientdata() is not used anymore.
> > >
> > > Looks good overall.
> > > A few comments inline.
> > >
> > > >
> > > > Signed-off-by: Théo Borém Fabris <theobf@usp.br>
> > > > ---
> > > > drivers/iio/dac/max5821.c | 30 ++++++++++++++++--------------
> > > > 1 file changed, 16 insertions(+), 14 deletions(-)
> > > >
> > > > diff --git a/drivers/iio/dac/max5821.c b/drivers/iio/dac/max5821.c
> > > > index bd6e75699a63..44c04ae70b32 100644
> > > > --- a/drivers/iio/dac/max5821.c
> > > > +++ b/drivers/iio/dac/max5821.c
> > > > @@ -294,6 +294,13 @@ static const struct iio_info max5821_info = {
> > > > .write_raw = max5821_write_raw,
> > > > };
> > > >
> > > > +static void max5821_regulator_disable(void *data)
> > > > +{
> > > > + struct regulator *rdata = data;
> > > > +
> > > > + regulator_disable(rdata);
> > >
> > > This can be simplified a bit:
> > >
> > > static void max5821_regulator_disable(void *reg)
> > > {
> > > regulator_disable(reg);
> > > }
> > >
> > > I used to do explicit casting, but then I also figured that it's not necessary.
> > >
> > Ok.
> >
> > > > +}
> > > > +
> > > > static int max5821_probe(struct i2c_client *client,
> > > > const struct i2c_device_id *id)
> > > > {
> > > > @@ -306,7 +313,6 @@ static int max5821_probe(struct i2c_client *client,
> > > > if (!indio_dev)
> > > > return -ENOMEM;
> > > > data = iio_priv(indio_dev);
> > > > - i2c_set_clientdata(client, indio_dev);
> > > > data->client = client;
> > > > mutex_init(&data->lock);
> > > >
> > > > @@ -331,6 +337,14 @@ static int max5821_probe(struct i2c_client *client,
> > > > goto error_free_reg;
> > > > }
> > > >
> > > > + ret = devm_add_action_or_reset(&client->dev, max5821_regulator_disable,
> > > > + data->vref_reg);
> > > > + if (ret) {
> > > > + dev_err(&client->dev,
> > > > + "Failed to add action to managed regulator: %d\n", ret);
> > > > + goto error_disable_reg;
> > >
> > > return ret;
> > >
> > > devm_add_action_or_reset() should call max5821_regulator_disable() in
> > > case of error
> > >
> > Ok.
> >
> > > > + }
> > > > +
> > > > ret = regulator_get_voltage(data->vref_reg);
> > > > if (ret < 0) {
> > > > dev_err(&client->dev,
> > > > @@ -346,7 +360,7 @@ static int max5821_probe(struct i2c_client *client,
> > > > indio_dev->modes = INDIO_DIRECT_MODE;
> > > > indio_dev->info = &max5821_info;
> > > >
> > > > - return iio_device_register(indio_dev);
> > > > + return devm_iio_device_register(&client->dev, indio_dev);
> > > >
> > > > error_disable_reg:
> > >
> > > This entire goto block should be removed.
> > > The idea of using only devm_ functions is to not have these goto statements.
> > >
> > I thought the action added via devm_add_action (and devres_add) was called only
> > on driver detach, thus the error_disable_reg label would be necessary
> > to handle the
>
> devm_add_action() yes
> this is devm_add_action_or_reset() which looks like this:
>
> static inline int devm_add_action_or_reset(struct device *dev,
> void (*action)(void *), void *data)
> {
> int ret;
>
> ret = devm_add_action(dev, action, data);
> if (ret)
> action(data);
>
> return ret;
> }
>
> it can be found in "include/linux/device.h"
>
> > possible error on regulator_get_voltage. Could you please clarify for
> > me when does
> > a driver detach happen?
>
> a driver detach happens when:
> * the kmod is unloaded (assuming the driver is running as a kmod)
> * manually unbinding the driver from sysfs ;
> a quick article about this [it's for USB, but other interfaces use
> the same mechanism]:
> https://lwn.net/Articles/143397/
> there should be something under /sys/bus/spi/drivers/xxxx/unbind
> * when the system powers down (reboots)
> * maybe there is some other new method to do this [that I don't know about]
>
Thank you so much.
So, should this goto error_disable_reg be replaced by
"regulator_disable(.); return ret;"?
ret = regulator_get_voltage(data->vref_reg);
if (ret < 0) {
dev_err(&client->dev,
"Failed to get voltage on regulator: %d\n", ret);
goto error_disable_reg;
}
> >
> > Thanks for your reply,
> > Théo
> >
> > > > regulator_disable(data->vref_reg);
> > > > @@ -356,17 +370,6 @@ static int max5821_probe(struct i2c_client *client,
> > > > return ret;
> > > > }
> > > >
> > > > -static int max5821_remove(struct i2c_client *client)
> > > > -{
> > > > - struct iio_dev *indio_dev = i2c_get_clientdata(client);
> > > > - struct max5821_data *data = iio_priv(indio_dev);
> > > > -
> > > > - iio_device_unregister(indio_dev);
> > > > - regulator_disable(data->vref_reg);
> > > > -
> > > > - return 0;
> > > > -}
> > > > -
> > > > static const struct i2c_device_id max5821_id[] = {
> > > > { "max5821", ID_MAX5821 },
> > > > { }
> > > > @@ -386,7 +389,6 @@ static struct i2c_driver max5821_driver = {
> > > > .pm = &max5821_pm_ops,
> > > > },
> > > > .probe = max5821_probe,
> > > > - .remove = max5821_remove,
> > > > .id_table = max5821_id,
> > > > };
> > > > module_i2c_driver(max5821_driver);
> > > > --
> > > > 2.20.1
> > > >
next prev parent reply other threads:[~2021-07-21 0:12 UTC|newest]
Thread overview: 8+ messages / expand[flat|nested] mbox.gz Atom feed top
2021-07-18 20:37 [PATCH] iio: dac: max5821: convert device register to device managed function Théo Borém Fabris
2021-07-19 7:32 ` Alexandru Ardelean
2021-07-19 15:24 ` Théo Borém Fabris
2021-07-20 7:22 ` Alexandru Ardelean
2021-07-20 7:33 ` Sa, Nuno
2021-07-21 0:11 ` Théo Borém Fabris [this message]
2021-07-21 7:23 ` Alexandru Ardelean
2021-07-24 22:48 ` Théo Borém Fabris
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=CAD5vTa_cR0da4qZ2JTB7G-QgZrSeZr3e8fp92S6WGMaCoUr15g@mail.gmail.com \
--to=theobf@usp.br \
--cc=ardeleanalex@gmail.com \
--cc=jic23@kernel.org \
--cc=lars@metafoo.de \
--cc=linux-iio@vger.kernel.org \
--cc=linux-kernel@vger.kernel.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).