Re: [PATCH 3/4] dt-bindings: iio: imu: add bosch BNO055 serdev driver bindings

[Andrea Merello <andrea.merello@gmail.com>]

Il giorno sab 17 lug 2021 alle ore 17:36 Jonathan Cameron
<jic23@kernel.org> ha scritto:
>
> On Thu, 15 Jul 2021 16:17:41 +0200
> Andrea Merello <andrea.merello@gmail.com> wrote:
>
> > Introduce new documentation file for the BNO055 serdev driver that will
> dt bindings are for the device not the driver (so don't mention driver
> in the binding or the patch description).

Ah, right

> > be included in next patches of this same series
> >
> > Signed-off-by: Andrea Merello <andrea.merello@iit.it>
> > Cc: Andrea Merello <andrea.merello@gmail.com>
> > Cc: Rob Herring <robh+dt@kernel.org>
> > Cc: Matt Ranostay <matt.ranostay@konsulko.com>
> > Cc: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
> > Cc: Vlad Dogaru <vlad.dogaru@intel.com>
> > Cc: linux-kernel@vger.kernel.org
> > Cc: linux-iio@vger.kernel.org
> > ---
> >  .../bindings/iio/imu/bosch,bno055-serial.yaml | 40 +++++++++++++++++++
> >  1 file changed, 40 insertions(+)
> >  create mode 100644 Documentation/devicetree/bindings/iio/imu/bosch,bno055-serial.yaml
> >
> > diff --git a/Documentation/devicetree/bindings/iio/imu/bosch,bno055-serial.yaml b/Documentation/devicetree/bindings/iio/imu/bosch,bno055-serial.yaml
> > new file mode 100644
> > index 000000000000..743c784ebc94
> > --- /dev/null
> > +++ b/Documentation/devicetree/bindings/iio/imu/bosch,bno055-serial.yaml
>
> Better to have just one doc covering this interface and i2c if that gets added.

OK

> > @@ -0,0 +1,40 @@
> > +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
> > +%YAML 1.2
> > +---
> > +$id: http://devicetree.org/schemas/iio/imu/bosch,bno055-serial.yaml#
> > +$schema: http://devicetree.org/meta-schemas/core.yaml#
> > +
> > +title: Serial-attached Bosch BNO055
> > +
> > +maintainers:
> > +  - Jonathan Cameron <jic23@kernel.org>
>
> That's just mean!  I have plenty of these to look after already! Joking
> aside, you'd be a better maintainer for this than me as more likely
> to pay attention.

Ok. I was really embarrassed about this: didn't want to proclaim me as
a maintainer, neither I wanted me to decide something about you :)


> > +
> > +description: |
> > +  Inertial Measurement Unit with Accelerometer, Gyroscope, Magnetometer and
> > +  internal MCU for sensor fusion
> > +  https://www.bosch-sensortec.com/products/smart-sensors/bno055/
> > +
> > +properties:
> > +  compatible:
> > +    enum:
> > +     - bosch,bno055-serial
> > +
> > +  reset-gpios:
> > +    maxItems: 1
> > +
> > +  clocks:
> > +    maxItems: 1
> > +
> > +required:
> > +  - compatible
> > +
> > +additionalProperties: false
> > +
> > +examples:
> > + - |
> > +   #include <dt-bindings/gpio/gpio.h>
> > +   bno055 {
>
> name needs to be the one for the device type found in the device tree spec or
> if it's not there, something in same 'spirit'.  Probably imu here

OK

> > +      compatible = "bosch,bno055-serial";
> Don't need the -serial. It will bind based on the bus this is under.
> Speaking of which, it's normal to provide that bus info as part of the example.
> See for example chemical/sensiron,scd30.yaml

OK

> > +      reset-gpios = <&gpio0 54 GPIO_ACTIVE_LOW>;
> > +      clocks = <&imu_clk>;
> > +   };
>