[PATCH 0/2] hid: intel-ish-hid: ipc: enable OOB support for EHL

[PATCH 0/2] hid: intel-ish-hid: ipc: enable OOB support for EHL

[Zhang Lixu]

The EHL (Elkhart Lake) based platforms provide a OOB (Out of band)
service, which allows wakup device when the system is in S5 (Soft-Off
state). This OOB service can be enabled/disabled from BIOS settings.

These two patches is to enable this feature for EHL platform.

We have tested these patches on both ISH platforms and EHL platforms,
it works fine.

Zhang Lixu (2):
  hid: intel-ish-hid: ipc: finish power flow for EHL OOB
  hid: intel-ish-hid: ipc: Address EHL Sx resume issues

 drivers/hid/intel-ish-hid/ipc/hw-ish.h  |  1 +
 drivers/hid/intel-ish-hid/ipc/ipc.c     | 27 +++++++++++++
 drivers/hid/intel-ish-hid/ipc/pci-ish.c | 54 ++++++++++++++++++++++++-
 3 files changed, 81 insertions(+), 1 deletion(-)

-- 
2.25.1

[PATCH 1/2] hid: intel-ish-hid: ipc: finish power flow for EHL OOB

[Zhang Lixu]

The EHL (Elkhart Lake) based platforms provide a OOB (Out of band)
service, which allows wakup device when the system is in S5 (Soft-Off
state). This OOB service can be enabled/disabled from BIOS settings. When
enabled, the ISH device gets PME wake capability. To enable PME wakeup,
driver also needs to enable ACPI GPE bit.

Once wakeup, BIOS will clear the wakeup bit to identify wakeup is
successful. So driver need to re-enable it in resume function to
keep the next wakeup capability.

Since this feature is only present on EHL, we use EHL PCI device id to
enable this feature.

Co-developed-by: Najumon Ba <najumon.ba@intel.com>
Signed-off-by: Najumon Ba <najumon.ba@intel.com>
Signed-off-by: Even Xu <even.xu@intel.com>
Signed-off-by: Zhang Lixu <lixu.zhang@intel.com>
---
 drivers/hid/intel-ish-hid/ipc/pci-ish.c | 48 +++++++++++++++++++++++++
 1 file changed, 48 insertions(+)

diff --git a/drivers/hid/intel-ish-hid/ipc/pci-ish.c b/drivers/hid/intel-ish-hid/ipc/pci-ish.c
index c6d48a8648b7..c9c5488e44cb 100644
--- a/drivers/hid/intel-ish-hid/ipc/pci-ish.c
+++ b/drivers/hid/intel-ish-hid/ipc/pci-ish.c
@@ -5,6 +5,7 @@
  * Copyright (c) 2014-2016, Intel Corporation.
  */
 
+#include <linux/acpi.h>
 #include <linux/module.h>
 #include <linux/moduleparam.h>
 #include <linux/kernel.h>
@@ -111,6 +112,42 @@ static inline bool ish_should_leave_d0i3(struct pci_dev *pdev)
 	return !pm_resume_via_firmware() || pdev->device == CHV_DEVICE_ID;
 }
 
+static int enable_gpe(struct device *dev)
+{
+#ifdef CONFIG_ACPI
+	acpi_status acpi_sts;
+	struct acpi_device *adev;
+	struct acpi_device_wakeup *wakeup;
+
+	adev = ACPI_COMPANION(dev);
+	if (!adev) {
+		dev_err(dev, "get acpi handle failed\n");
+		return -ENODEV;
+	}
+	wakeup = &adev->wakeup;
+
+	acpi_sts = acpi_enable_gpe(wakeup->gpe_device, wakeup->gpe_number);
+	if (ACPI_FAILURE(acpi_sts)) {
+		dev_err(dev, "enable ose_gpe failed\n");
+		return -EIO;
+	}
+
+	return 0;
+#else
+	return -ENODEV;
+#endif
+}
+
+static void enable_pme_wake(struct pci_dev *pdev)
+{
+	if ((pci_pme_capable(pdev, PCI_D0) ||
+	     pci_pme_capable(pdev, PCI_D3hot) ||
+	     pci_pme_capable(pdev, PCI_D3cold)) && !enable_gpe(&pdev->dev)) {
+		pci_pme_active(pdev, true);
+		dev_dbg(&pdev->dev, "ish ipc driver pme wake enabled\n");
+	}
+}
+
 /**
  * ish_probe() - PCI driver probe callback
  * @pdev:	pci device
@@ -179,6 +216,10 @@ static int ish_probe(struct pci_dev *pdev, const struct pci_device_id *ent)
 	init_waitqueue_head(&ishtp->suspend_wait);
 	init_waitqueue_head(&ishtp->resume_wait);
 
+	/* Enable PME for EHL */
+	if (pdev->device == EHL_Ax_DEVICE_ID)
+		enable_pme_wake(pdev);
+
 	ret = ish_init(ishtp);
 	if (ret)
 		return ret;
@@ -317,6 +358,13 @@ static int __maybe_unused ish_resume(struct device *device)
 	struct pci_dev *pdev = to_pci_dev(device);
 	struct ishtp_device *dev = pci_get_drvdata(pdev);
 
+	/* add this to finish power flow for EHL */
+	if (dev->pdev->device == EHL_Ax_DEVICE_ID) {
+		pci_set_power_state(pdev, PCI_D0);
+		enable_pme_wake(pdev);
+		dev_dbg(dev->devc, "set power state to D0 for ehl\n");
+	}
+
 	ish_resume_device = device;
 	dev->resume_flag = 1;
 
-- 
2.25.1

[PATCH 2/2] hid: intel-ish-hid: ipc: Address EHL Sx resume issues

[Zhang Lixu]

When OOB is disabled, FW will be power gated when system is in S3/S4/S5
which is the same behavior with legacy ISH FW.
When OOB is enabled, FW will always power on which is totally different
comparing to legacy ISH FW.

So NO_D3 flag is not enough to check FW's status after resume.
Here we can use IPC FW status register to check host link status.
If it is false, it means FW get reset after power gated, need go through
the whole initialization flow; If it is true, it means FW is alive, just
set host ready bit to let fw know host is up.

Co-developed-by: Wei Jiang <wei.w.jiang@intel.com>
Signed-off-by: Wei Jiang <wei.w.jiang@intel.com>
Signed-off-by: Even Xu <even.xu@intel.com>
Signed-off-by: Zhang Lixu <lixu.zhang@intel.com>
---
 drivers/hid/intel-ish-hid/ipc/hw-ish.h  |  1 +
 drivers/hid/intel-ish-hid/ipc/ipc.c     | 27 +++++++++++++++++++++++++
 drivers/hid/intel-ish-hid/ipc/pci-ish.c |  6 +++++-
 3 files changed, 33 insertions(+), 1 deletion(-)

diff --git a/drivers/hid/intel-ish-hid/ipc/hw-ish.h b/drivers/hid/intel-ish-hid/ipc/hw-ish.h
index 1fb294ca463e..111ad259ba74 100644
--- a/drivers/hid/intel-ish-hid/ipc/hw-ish.h
+++ b/drivers/hid/intel-ish-hid/ipc/hw-ish.h
@@ -81,5 +81,6 @@ struct ishtp_device *ish_dev_init(struct pci_dev *pdev);
 int ish_hw_start(struct ishtp_device *dev);
 void ish_device_disable(struct ishtp_device *dev);
 int ish_disable_dma(struct ishtp_device *dev);
+void ish_set_host_ready(struct ishtp_device *dev);
 
 #endif /* _ISHTP_HW_ISH_H_ */
diff --git a/drivers/hid/intel-ish-hid/ipc/ipc.c b/drivers/hid/intel-ish-hid/ipc/ipc.c
index a45ac7fa417b..47bbeb8b492b 100644
--- a/drivers/hid/intel-ish-hid/ipc/ipc.c
+++ b/drivers/hid/intel-ish-hid/ipc/ipc.c
@@ -193,6 +193,33 @@ static void ish_clr_host_rdy(struct ishtp_device *dev)
 	ish_reg_write(dev, IPC_REG_HOST_COMM, host_status);
 }
 
+static bool ish_chk_host_rdy(struct ishtp_device *dev)
+{
+	uint32_t host_status = ish_reg_read(dev, IPC_REG_HOST_COMM);
+
+	return (host_status & IPC_HOSTCOMM_READY_BIT);
+}
+
+/**
+ * ish_set_host_ready() - reconfig ipc host registers
+ * @dev: ishtp device pointer
+ *
+ * Set host to ready state
+ * This API is called in some case:
+ *    fw is still on, but ipc is powered down.
+ *    such as OOB case.
+ *
+ * Return: 0 for success else error fault code
+ */
+void ish_set_host_ready(struct ishtp_device *dev)
+{
+	if (ish_chk_host_rdy(dev))
+		return;
+
+	ish_set_host_rdy(dev);
+	set_host_ready(dev);
+}
+
 /**
  * _ishtp_read_hdr() - Read message header
  * @dev: ISHTP device pointer
diff --git a/drivers/hid/intel-ish-hid/ipc/pci-ish.c b/drivers/hid/intel-ish-hid/ipc/pci-ish.c
index c9c5488e44cb..8cb40696984a 100644
--- a/drivers/hid/intel-ish-hid/ipc/pci-ish.c
+++ b/drivers/hid/intel-ish-hid/ipc/pci-ish.c
@@ -259,11 +259,15 @@ static void __maybe_unused ish_resume_handler(struct work_struct *work)
 {
 	struct pci_dev *pdev = to_pci_dev(ish_resume_device);
 	struct ishtp_device *dev = pci_get_drvdata(pdev);
+	uint32_t fwsts = dev->ops->get_fw_status(dev);
 	int ret;
 
-	if (ish_should_leave_d0i3(pdev) && !dev->suspend_flag) {
+	if (ish_should_leave_d0i3(pdev) && !dev->suspend_flag
+			&& IPC_IS_ISH_ILUP(fwsts)) {
 		disable_irq_wake(pdev->irq);
 
+		ish_set_host_ready(dev);
+
 		ishtp_send_resume(dev);
 
 		/* Waiting to get resume response */
-- 
2.25.1

Re: [PATCH 0/2] hid: intel-ish-hid: ipc: enable OOB support for EHL

[Jiri Kosina]

On Wed, 16 Dec 2020, Zhang Lixu wrote:

> The EHL (Elkhart Lake) based platforms provide a OOB (Out of band)
> service, which allows wakup device when the system is in S5 (Soft-Off
> state). This OOB service can be enabled/disabled from BIOS settings.
> 
> These two patches is to enable this feature for EHL platform.
> 
> We have tested these patches on both ISH platforms and EHL platforms,
> it works fine.
> 
> Zhang Lixu (2):
>   hid: intel-ish-hid: ipc: finish power flow for EHL OOB
>   hid: intel-ish-hid: ipc: Address EHL Sx resume issues
> 
>  drivers/hid/intel-ish-hid/ipc/hw-ish.h  |  1 +
>  drivers/hid/intel-ish-hid/ipc/ipc.c     | 27 +++++++++++++
>  drivers/hid/intel-ish-hid/ipc/pci-ish.c | 54 ++++++++++++++++++++++++-
>  3 files changed, 81 insertions(+), 1 deletion(-)

Srinivas, can I please get your Acked-by / Reviewed-by for this? Thanks,

-- 
Jiri Kosina
SUSE Labs

Re: [PATCH 1/2] hid: intel-ish-hid: ipc: finish power flow for EHL OOB

[Srinivas Pandruvada]

On Wed, 2020-12-16 at 14:36 +0800, Zhang Lixu wrote:
> The EHL (Elkhart Lake) based platforms provide a OOB (Out of band)
> service, which allows wakup device when the system is in S5 (Soft-Off
> state). This OOB service can be enabled/disabled from BIOS settings.
> When
> enabled, the ISH device gets PME wake capability. To enable PME
> wakeup,
> driver also needs to enable ACPI GPE bit.
> 
> Once wakeup, BIOS will clear the wakeup bit to identify wakeup is
> successful. So driver need to re-enable it in resume function to
> keep the next wakeup capability.
> 
> Since this feature is only present on EHL, we use EHL PCI device id
> to
> enable this feature.
> 
> Co-developed-by: Najumon Ba <najumon.ba@intel.com>
> Signed-off-by: Najumon Ba <najumon.ba@intel.com>
> Signed-off-by: Even Xu <even.xu@intel.com>
> Signed-off-by: Zhang Lixu <lixu.zhang@intel.com>
Acked-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>

> ---
>  drivers/hid/intel-ish-hid/ipc/pci-ish.c | 48
> +++++++++++++++++++++++++
>  1 file changed, 48 insertions(+)
> 
> diff --git a/drivers/hid/intel-ish-hid/ipc/pci-ish.c
> b/drivers/hid/intel-ish-hid/ipc/pci-ish.c
> index c6d48a8648b7..c9c5488e44cb 100644
> --- a/drivers/hid/intel-ish-hid/ipc/pci-ish.c
> +++ b/drivers/hid/intel-ish-hid/ipc/pci-ish.c
> @@ -5,6 +5,7 @@
>   * Copyright (c) 2014-2016, Intel Corporation.
>   */
>  
> +#include <linux/acpi.h>
>  #include <linux/module.h>
>  #include <linux/moduleparam.h>
>  #include <linux/kernel.h>
> @@ -111,6 +112,42 @@ static inline bool ish_should_leave_d0i3(struct
> pci_dev *pdev)
>         return !pm_resume_via_firmware() || pdev->device ==
> CHV_DEVICE_ID;
>  }
>  
> +static int enable_gpe(struct device *dev)
> +{
> +#ifdef CONFIG_ACPI
> +       acpi_status acpi_sts;
> +       struct acpi_device *adev;
> +       struct acpi_device_wakeup *wakeup;
> +
> +       adev = ACPI_COMPANION(dev);
> +       if (!adev) {
> +               dev_err(dev, "get acpi handle failed\n");
> +               return -ENODEV;
> +       }
> +       wakeup = &adev->wakeup;
> +
> +       acpi_sts = acpi_enable_gpe(wakeup->gpe_device, wakeup-
> >gpe_number);
> +       if (ACPI_FAILURE(acpi_sts)) {
> +               dev_err(dev, "enable ose_gpe failed\n");
> +               return -EIO;
> +       }
> +
> +       return 0;
> +#else
> +       return -ENODEV;
> +#endif
> +}
> +
> +static void enable_pme_wake(struct pci_dev *pdev)
> +{
> +       if ((pci_pme_capable(pdev, PCI_D0) ||
> +            pci_pme_capable(pdev, PCI_D3hot) ||
> +            pci_pme_capable(pdev, PCI_D3cold)) && !enable_gpe(&pdev-
> >dev)) {
> +               pci_pme_active(pdev, true);
> +               dev_dbg(&pdev->dev, "ish ipc driver pme wake
> enabled\n");
> +       }
> +}
> +
>  /**
>   * ish_probe() - PCI driver probe callback
>   * @pdev:      pci device
> @@ -179,6 +216,10 @@ static int ish_probe(struct pci_dev *pdev, const
> struct pci_device_id *ent)
>         init_waitqueue_head(&ishtp->suspend_wait);
>         init_waitqueue_head(&ishtp->resume_wait);
>  
> +       /* Enable PME for EHL */
> +       if (pdev->device == EHL_Ax_DEVICE_ID)
> +               enable_pme_wake(pdev);
> +
>         ret = ish_init(ishtp);
>         if (ret)
>                 return ret;
> @@ -317,6 +358,13 @@ static int __maybe_unused ish_resume(struct
> device *device)
>         struct pci_dev *pdev = to_pci_dev(device);
>         struct ishtp_device *dev = pci_get_drvdata(pdev);
>  
> +       /* add this to finish power flow for EHL */
> +       if (dev->pdev->device == EHL_Ax_DEVICE_ID) {
> +               pci_set_power_state(pdev, PCI_D0);
> +               enable_pme_wake(pdev);
> +               dev_dbg(dev->devc, "set power state to D0 for
> ehl\n");
> +       }
> +
>         ish_resume_device = device;
>         dev->resume_flag = 1;
>  

Re: [PATCH 2/2] hid: intel-ish-hid: ipc: Address EHL Sx resume issues

[Srinivas Pandruvada]

On Wed, 2020-12-16 at 14:36 +0800, Zhang Lixu wrote:
> When OOB is disabled, FW will be power gated when system is in
> S3/S4/S5
> which is the same behavior with legacy ISH FW.
> When OOB is enabled, FW will always power on which is totally
> different
> comparing to legacy ISH FW.
> 
> So NO_D3 flag is not enough to check FW's status after resume.
> Here we can use IPC FW status register to check host link status.
> If it is false, it means FW get reset after power gated, need go
> through
> the whole initialization flow; If it is true, it means FW is alive,
> just
> set host ready bit to let fw know host is up.
> 
> Co-developed-by: Wei Jiang <wei.w.jiang@intel.com>
> Signed-off-by: Wei Jiang <wei.w.jiang@intel.com>
> Signed-off-by: Even Xu <even.xu@intel.com>
> Signed-off-by: Zhang Lixu <lixu.zhang@intel.com>
Acked-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>

> ---
>  drivers/hid/intel-ish-hid/ipc/hw-ish.h  |  1 +
>  drivers/hid/intel-ish-hid/ipc/ipc.c     | 27
> +++++++++++++++++++++++++
>  drivers/hid/intel-ish-hid/ipc/pci-ish.c |  6 +++++-
>  3 files changed, 33 insertions(+), 1 deletion(-)
> 
> diff --git a/drivers/hid/intel-ish-hid/ipc/hw-ish.h
> b/drivers/hid/intel-ish-hid/ipc/hw-ish.h
> index 1fb294ca463e..111ad259ba74 100644
> --- a/drivers/hid/intel-ish-hid/ipc/hw-ish.h
> +++ b/drivers/hid/intel-ish-hid/ipc/hw-ish.h
> @@ -81,5 +81,6 @@ struct ishtp_device *ish_dev_init(struct pci_dev
> *pdev);
>  int ish_hw_start(struct ishtp_device *dev);
>  void ish_device_disable(struct ishtp_device *dev);
>  int ish_disable_dma(struct ishtp_device *dev);
> +void ish_set_host_ready(struct ishtp_device *dev);
>  
>  #endif /* _ISHTP_HW_ISH_H_ */
> diff --git a/drivers/hid/intel-ish-hid/ipc/ipc.c b/drivers/hid/intel-
> ish-hid/ipc/ipc.c
> index a45ac7fa417b..47bbeb8b492b 100644
> --- a/drivers/hid/intel-ish-hid/ipc/ipc.c
> +++ b/drivers/hid/intel-ish-hid/ipc/ipc.c
> @@ -193,6 +193,33 @@ static void ish_clr_host_rdy(struct ishtp_device
> *dev)
>         ish_reg_write(dev, IPC_REG_HOST_COMM, host_status);
>  }
>  
> +static bool ish_chk_host_rdy(struct ishtp_device *dev)
> +{
> +       uint32_t host_status = ish_reg_read(dev, IPC_REG_HOST_COMM);
> +
> +       return (host_status & IPC_HOSTCOMM_READY_BIT);
> +}
> +
> +/**
> + * ish_set_host_ready() - reconfig ipc host registers
> + * @dev: ishtp device pointer
> + *
> + * Set host to ready state
> + * This API is called in some case:
> + *    fw is still on, but ipc is powered down.
> + *    such as OOB case.
> + *
> + * Return: 0 for success else error fault code
> + */
> +void ish_set_host_ready(struct ishtp_device *dev)
> +{
> +       if (ish_chk_host_rdy(dev))
> +               return;
> +
> +       ish_set_host_rdy(dev);
> +       set_host_ready(dev);
> +}
> +
>  /**
>   * _ishtp_read_hdr() - Read message header
>   * @dev: ISHTP device pointer
> diff --git a/drivers/hid/intel-ish-hid/ipc/pci-ish.c
> b/drivers/hid/intel-ish-hid/ipc/pci-ish.c
> index c9c5488e44cb..8cb40696984a 100644
> --- a/drivers/hid/intel-ish-hid/ipc/pci-ish.c
> +++ b/drivers/hid/intel-ish-hid/ipc/pci-ish.c
> @@ -259,11 +259,15 @@ static void __maybe_unused
> ish_resume_handler(struct work_struct *work)
>  {
>         struct pci_dev *pdev = to_pci_dev(ish_resume_device);
>         struct ishtp_device *dev = pci_get_drvdata(pdev);
> +       uint32_t fwsts = dev->ops->get_fw_status(dev);
>         int ret;
>  
> -       if (ish_should_leave_d0i3(pdev) && !dev->suspend_flag) {
> +       if (ish_should_leave_d0i3(pdev) && !dev->suspend_flag
> +                       && IPC_IS_ISH_ILUP(fwsts)) {
>                 disable_irq_wake(pdev->irq);
>  
> +               ish_set_host_ready(dev);
> +
>                 ishtp_send_resume(dev);
>  
>                 /* Waiting to get resume response */

Re: [PATCH 0/2] hid: intel-ish-hid: ipc: enable OOB support for EHL

[Srinivas Pandruvada]

On Mon, 2021-01-04 at 16:12 +0100, Jiri Kosina wrote:
> On Wed, 16 Dec 2020, Zhang Lixu wrote:
> 
> > The EHL (Elkhart Lake) based platforms provide a OOB (Out of band)
> > service, which allows wakup device when the system is in S5 (Soft-
> > Off
> > state). This OOB service can be enabled/disabled from BIOS
> > settings.
> > 
> > These two patches is to enable this feature for EHL platform.
> > 
> > We have tested these patches on both ISH platforms and EHL
> > platforms,
> > it works fine.
> > 
> > Zhang Lixu (2):
> >   hid: intel-ish-hid: ipc: finish power flow for EHL OOB
> >   hid: intel-ish-hid: ipc: Address EHL Sx resume issues
> > 
> >  drivers/hid/intel-ish-hid/ipc/hw-ish.h  |  1 +
> >  drivers/hid/intel-ish-hid/ipc/ipc.c     | 27 +++++++++++++
> >  drivers/hid/intel-ish-hid/ipc/pci-ish.c | 54
> > ++++++++++++++++++++++++-
> >  3 files changed, 81 insertions(+), 1 deletion(-)
> 
> Srinivas, can I please get your Acked-by / Reviewed-by for this?
Acked on individual patches.

Thanks,
Srinivas


> Thanks,
> 

Re: [PATCH 0/2] hid: intel-ish-hid: ipc: enable OOB support for EHL

[Zhang, Lixu]

On Mon, Jan 04, 2021 at 08:01:36AM -0800, Srinivas Pandruvada wrote:
> On Mon, 2021-01-04 at 16:12 +0100, Jiri Kosina wrote:
> > On Wed, 16 Dec 2020, Zhang Lixu wrote:
> > 
> > > The EHL (Elkhart Lake) based platforms provide a OOB (Out of band)
> > > service, which allows wakup device when the system is in S5 (Soft-
> > > Off
> > > state). This OOB service can be enabled/disabled from BIOS
> > > settings.
> > > 
> > > These two patches is to enable this feature for EHL platform.
> > > 
> > > We have tested these patches on both ISH platforms and EHL
> > > platforms,
> > > it works fine.
> > > 
> > > Zhang Lixu (2):
> > >   hid: intel-ish-hid: ipc: finish power flow for EHL OOB
> > >   hid: intel-ish-hid: ipc: Address EHL Sx resume issues
> > > 
> > >  drivers/hid/intel-ish-hid/ipc/hw-ish.h  |  1 +
> > >  drivers/hid/intel-ish-hid/ipc/ipc.c     | 27 +++++++++++++
> > >  drivers/hid/intel-ish-hid/ipc/pci-ish.c | 54
> > > ++++++++++++++++++++++++-
> > >  3 files changed, 81 insertions(+), 1 deletion(-)
> > 
> > Srinivas, can I please get your Acked-by / Reviewed-by for this?
> Acked on individual patches.
> 
> Thanks,
> Srinivas
> 
> 
> > Thanks,
> > 
> 
> 

Thanks.

Re: [PATCH 0/2] hid: intel-ish-hid: ipc: enable OOB support for EHL

[Jiri Kosina]

On Wed, 16 Dec 2020, Zhang Lixu wrote:

> The EHL (Elkhart Lake) based platforms provide a OOB (Out of band)
> service, which allows wakup device when the system is in S5 (Soft-Off
> state). This OOB service can be enabled/disabled from BIOS settings.
> 
> These two patches is to enable this feature for EHL platform.
> 
> We have tested these patches on both ISH platforms and EHL platforms,
> it works fine.
> 
> Zhang Lixu (2):
>   hid: intel-ish-hid: ipc: finish power flow for EHL OOB
>   hid: intel-ish-hid: ipc: Address EHL Sx resume issues
> 
>  drivers/hid/intel-ish-hid/ipc/hw-ish.h  |  1 +
>  drivers/hid/intel-ish-hid/ipc/ipc.c     | 27 +++++++++++++
>  drivers/hid/intel-ish-hid/ipc/pci-ish.c | 54 ++++++++++++++++++++++++-
>  3 files changed, 81 insertions(+), 1 deletion(-)

Applied to hid.git#for-5.12/intel-ish.

-- 
Jiri Kosina
SUSE Labs