Linux-LEDs Archive on lore.kernel.org
 help / color / Atom feed
* [PATCH V5 0/2] Fix WLED FSC Sync and brightness Sync settings
@ 2021-03-18 12:39 Kiran Gunda
  2021-03-18 12:39 ` [PATCH V5 1/2] backlight: qcom-wled: Fix FSC update issue for WLED5 Kiran Gunda
  2021-03-18 12:39 ` [PATCH V5 2/2] backlight: qcom-wled: Correct the sync_toggle sequence Kiran Gunda
  0 siblings, 2 replies; 5+ messages in thread
From: Kiran Gunda @ 2021-03-18 12:39 UTC (permalink / raw)
  To: bjorn.andersson, jingoohan1, lee.jones, b.zolnierkie, dri-devel,
	daniel.thompson, jacek.anaszewski, pavel, robh+dt, mark.rutland,
	linux-leds, devicetree, linux-kernel, phone-devel
  Cc: linux-arm-msm, Kiran Gunda

This patch series has the following two WLED fixes
 1. As per the current implementation, for WLED5, after
    the FSC (Full Scale Current) update the driver is incorrectly
    toggling the MOD_SYNC register instead of toggling the SYNC register.
    The patch 1/2 fixes this by toggling the SYNC register after
    FSC update.

 2. Currently, the sync bits are set-then-cleared after FSC and brightness
    update. As per hardware team recommendation the FSC and brightness sync
    takes place from clear-then-set transition of the sync bits.
    The patch 2/2 fies this issue.

changes from V4:
  1. Rebased this patch series on the below patch.
     "backlight-qcom-wled-Use-sink_addr-for-sync-toggle.patch".

Changes from V3:
  1. Updated the patch description as per Daneil's suggestion.
  2. Added Daniel's "Reviewed-by" tag for patch 2/2.
  3. Updated the cover letter to use "set" and "clear" properly.
 
Changes from V2:
  1. Added Daniel's "Reviewed-by" tag for patch 1/2.
  2. Updated the patch 2/2 description with "set" and "clear"
     terminology instead of "1" and "0".
  3. Updated the cover letter with "set" and "clear" terminology
     instead of "1" and "0".

Changes from V1:
  1. Updated the cover letter.
  2. Updated the description of the patches as per Daniel's suggestion.

Kiran Gunda (2):
  backlight: qcom-wled: Fix FSC update issue for WLED5
  backlight: qcom-wled: Correct the sync_toggle sequence

 drivers/video/backlight/qcom-wled.c | 37 +++++++++++++++++++++++++------------
 1 file changed, 25 insertions(+), 12 deletions(-)

-- 
The Qualcomm Innovation Center, Inc. is a member of the Code Aurora Forum,
 a Linux Foundation Collaborative Project


^ permalink raw reply	[flat|nested] 5+ messages in thread

* [PATCH V5 1/2] backlight: qcom-wled: Fix FSC update issue for WLED5
  2021-03-18 12:39 [PATCH V5 0/2] Fix WLED FSC Sync and brightness Sync settings Kiran Gunda
@ 2021-03-18 12:39 ` Kiran Gunda
  2021-03-22 17:34   ` Lee Jones
  2021-03-18 12:39 ` [PATCH V5 2/2] backlight: qcom-wled: Correct the sync_toggle sequence Kiran Gunda
  1 sibling, 1 reply; 5+ messages in thread
From: Kiran Gunda @ 2021-03-18 12:39 UTC (permalink / raw)
  To: bjorn.andersson, jingoohan1, lee.jones, b.zolnierkie, dri-devel,
	daniel.thompson, jacek.anaszewski, pavel, robh+dt, mark.rutland,
	linux-leds, devicetree, linux-kernel, phone-devel, Andy Gross,
	linux-arm-msm, linux-fbdev
  Cc: Kiran Gunda

Currently, for WLED5, the FSC (Full scale current) setting is not
updated properly due to driver toggling the wrong register after
an FSC update.

On WLED5 we should only toggle the MOD_SYNC bit after a brightness
update. For an FSC update we need to toggle the SYNC bits instead.

Fix it by adopting the common wled3_sync_toggle() for WLED5 and
introducing new code to the brightness update path to compensate.

Signed-off-by: Kiran Gunda <kgunda@codeaurora.org>
Reviewed-by: Daniel Thompson <daniel.thompson@linaro.org>
---
 drivers/video/backlight/qcom-wled.c | 25 +++++++++++++++++++------
 1 file changed, 19 insertions(+), 6 deletions(-)

diff --git a/drivers/video/backlight/qcom-wled.c b/drivers/video/backlight/qcom-wled.c
index fc8b443..e9fbe24 100644
--- a/drivers/video/backlight/qcom-wled.c
+++ b/drivers/video/backlight/qcom-wled.c
@@ -348,7 +348,7 @@ static int wled3_sync_toggle(struct wled *wled)
 	return rc;
 }
 
-static int wled5_sync_toggle(struct wled *wled)
+static int wled5_mod_sync_toggle(struct wled *wled)
 {
 	int rc;
 	u8 val;
@@ -445,10 +445,23 @@ static int wled_update_status(struct backlight_device *bl)
 			goto unlock_mutex;
 		}
 
-		rc = wled->wled_sync_toggle(wled);
-		if (rc < 0) {
-			dev_err(wled->dev, "wled sync failed rc:%d\n", rc);
-			goto unlock_mutex;
+		if (wled->version < 5) {
+			rc = wled->wled_sync_toggle(wled);
+			if (rc < 0) {
+				dev_err(wled->dev, "wled sync failed rc:%d\n", rc);
+				goto unlock_mutex;
+			}
+		} else {
+			/*
+			 * For WLED5 toggling the MOD_SYNC_BIT updates the
+			 * brightness
+			 */
+			rc = wled5_mod_sync_toggle(wled);
+			if (rc < 0) {
+				dev_err(wled->dev, "wled mod sync failed rc:%d\n",
+					rc);
+				goto unlock_mutex;
+			}
 		}
 	}
 
@@ -1459,7 +1472,7 @@ static int wled_configure(struct wled *wled)
 		size = ARRAY_SIZE(wled5_opts);
 		*cfg = wled5_config_defaults;
 		wled->wled_set_brightness = wled5_set_brightness;
-		wled->wled_sync_toggle = wled5_sync_toggle;
+		wled->wled_sync_toggle = wled3_sync_toggle;
 		wled->wled_cabc_config = wled5_cabc_config;
 		wled->wled_ovp_delay = wled5_ovp_delay;
 		wled->wled_auto_detection_required =
-- 
The Qualcomm Innovation Center, Inc. is a member of the Code Aurora Forum,
 a Linux Foundation Collaborative Project


^ permalink raw reply	[flat|nested] 5+ messages in thread

* [PATCH V5 2/2] backlight: qcom-wled: Correct the sync_toggle sequence
  2021-03-18 12:39 [PATCH V5 0/2] Fix WLED FSC Sync and brightness Sync settings Kiran Gunda
  2021-03-18 12:39 ` [PATCH V5 1/2] backlight: qcom-wled: Fix FSC update issue for WLED5 Kiran Gunda
@ 2021-03-18 12:39 ` Kiran Gunda
  2021-03-23  9:40   ` Lee Jones
  1 sibling, 1 reply; 5+ messages in thread
From: Kiran Gunda @ 2021-03-18 12:39 UTC (permalink / raw)
  To: bjorn.andersson, jingoohan1, lee.jones, b.zolnierkie, dri-devel,
	daniel.thompson, jacek.anaszewski, pavel, robh+dt, mark.rutland,
	linux-leds, devicetree, linux-kernel, phone-devel, Andy Gross,
	linux-arm-msm, linux-fbdev
  Cc: Kiran Gunda

As per the current implementation, after FSC (Full Scale Current)
and brightness update the sync bits are set-then-cleared.
But, the FSC and brightness sync takes place when the sync bits are
set (e.g. on a rising edge). So the hardware team recommends a
clear-then-set approach in order to guarantee such a transition
regardless of the previous register state.

Signed-off-by: Kiran Gunda <kgunda@codeaurora.org>
Reviewed-by: Daniel Thompson <daniel.thompson@linaro.org>
---
 drivers/video/backlight/qcom-wled.c | 12 ++++++------
 1 file changed, 6 insertions(+), 6 deletions(-)

diff --git a/drivers/video/backlight/qcom-wled.c b/drivers/video/backlight/qcom-wled.c
index e9fbe24..7c02f87 100644
--- a/drivers/video/backlight/qcom-wled.c
+++ b/drivers/video/backlight/qcom-wled.c
@@ -337,13 +337,13 @@ static int wled3_sync_toggle(struct wled *wled)
 
 	rc = regmap_update_bits(wled->regmap,
 				wled->sink_addr + WLED3_SINK_REG_SYNC,
-				mask, mask);
+				mask, WLED3_SINK_REG_SYNC_CLEAR);
 	if (rc < 0)
 		return rc;
 
 	rc = regmap_update_bits(wled->regmap,
 				wled->sink_addr + WLED3_SINK_REG_SYNC,
-				mask, WLED3_SINK_REG_SYNC_CLEAR);
+				mask, mask);
 
 	return rc;
 }
@@ -353,17 +353,17 @@ static int wled5_mod_sync_toggle(struct wled *wled)
 	int rc;
 	u8 val;
 
-	val = (wled->cfg.mod_sel == MOD_A) ? WLED5_SINK_REG_SYNC_MOD_A_BIT :
-					     WLED5_SINK_REG_SYNC_MOD_B_BIT;
 	rc = regmap_update_bits(wled->regmap,
 				wled->sink_addr + WLED5_SINK_REG_MOD_SYNC_BIT,
-				WLED5_SINK_REG_SYNC_MASK, val);
+				WLED5_SINK_REG_SYNC_MASK, 0);
 	if (rc < 0)
 		return rc;
 
+	val = (wled->cfg.mod_sel == MOD_A) ? WLED5_SINK_REG_SYNC_MOD_A_BIT :
+					     WLED5_SINK_REG_SYNC_MOD_B_BIT;
 	return regmap_update_bits(wled->regmap,
 				  wled->sink_addr + WLED5_SINK_REG_MOD_SYNC_BIT,
-				  WLED5_SINK_REG_SYNC_MASK, 0);
+				  WLED5_SINK_REG_SYNC_MASK, val);
 }
 
 static int wled_ovp_fault_status(struct wled *wled, bool *fault_set)
-- 
The Qualcomm Innovation Center, Inc. is a member of the Code Aurora Forum,
 a Linux Foundation Collaborative Project


^ permalink raw reply	[flat|nested] 5+ messages in thread

* Re: [PATCH V5 1/2] backlight: qcom-wled: Fix FSC update issue for WLED5
  2021-03-18 12:39 ` [PATCH V5 1/2] backlight: qcom-wled: Fix FSC update issue for WLED5 Kiran Gunda
@ 2021-03-22 17:34   ` Lee Jones
  0 siblings, 0 replies; 5+ messages in thread
From: Lee Jones @ 2021-03-22 17:34 UTC (permalink / raw)
  To: Kiran Gunda
  Cc: bjorn.andersson, jingoohan1, b.zolnierkie, dri-devel,
	daniel.thompson, jacek.anaszewski, pavel, robh+dt, mark.rutland,
	linux-leds, devicetree, linux-kernel, phone-devel, Andy Gross,
	linux-arm-msm, linux-fbdev

On Thu, 18 Mar 2021, Kiran Gunda wrote:

> Currently, for WLED5, the FSC (Full scale current) setting is not
> updated properly due to driver toggling the wrong register after
> an FSC update.
> 
> On WLED5 we should only toggle the MOD_SYNC bit after a brightness
> update. For an FSC update we need to toggle the SYNC bits instead.
> 
> Fix it by adopting the common wled3_sync_toggle() for WLED5 and
> introducing new code to the brightness update path to compensate.
> 
> Signed-off-by: Kiran Gunda <kgunda@codeaurora.org>
> Reviewed-by: Daniel Thompson <daniel.thompson@linaro.org>
> ---
>  drivers/video/backlight/qcom-wled.c | 25 +++++++++++++++++++------
>  1 file changed, 19 insertions(+), 6 deletions(-)

Applied, thanks.

-- 
Lee Jones [李琼斯]
Senior Technical Lead - Developer Services
Linaro.org │ Open source software for Arm SoCs
Follow Linaro: Facebook | Twitter | Blog

^ permalink raw reply	[flat|nested] 5+ messages in thread

* Re: [PATCH V5 2/2] backlight: qcom-wled: Correct the sync_toggle sequence
  2021-03-18 12:39 ` [PATCH V5 2/2] backlight: qcom-wled: Correct the sync_toggle sequence Kiran Gunda
@ 2021-03-23  9:40   ` Lee Jones
  0 siblings, 0 replies; 5+ messages in thread
From: Lee Jones @ 2021-03-23  9:40 UTC (permalink / raw)
  To: Kiran Gunda
  Cc: bjorn.andersson, jingoohan1, b.zolnierkie, dri-devel,
	daniel.thompson, jacek.anaszewski, pavel, robh+dt, mark.rutland,
	linux-leds, devicetree, linux-kernel, phone-devel, Andy Gross,
	linux-arm-msm, linux-fbdev

On Thu, 18 Mar 2021, Kiran Gunda wrote:

> As per the current implementation, after FSC (Full Scale Current)
> and brightness update the sync bits are set-then-cleared.
> But, the FSC and brightness sync takes place when the sync bits are
> set (e.g. on a rising edge). So the hardware team recommends a
> clear-then-set approach in order to guarantee such a transition
> regardless of the previous register state.
> 
> Signed-off-by: Kiran Gunda <kgunda@codeaurora.org>
> Reviewed-by: Daniel Thompson <daniel.thompson@linaro.org>
> ---
>  drivers/video/backlight/qcom-wled.c | 12 ++++++------
>  1 file changed, 6 insertions(+), 6 deletions(-)

Applied, thanks.

-- 
Lee Jones [李琼斯]
Senior Technical Lead - Developer Services
Linaro.org │ Open source software for Arm SoCs
Follow Linaro: Facebook | Twitter | Blog

^ permalink raw reply	[flat|nested] 5+ messages in thread

end of thread, back to index

Thread overview: 5+ messages (download: mbox.gz / follow: Atom feed)
-- links below jump to the message on this page --
2021-03-18 12:39 [PATCH V5 0/2] Fix WLED FSC Sync and brightness Sync settings Kiran Gunda
2021-03-18 12:39 ` [PATCH V5 1/2] backlight: qcom-wled: Fix FSC update issue for WLED5 Kiran Gunda
2021-03-22 17:34   ` Lee Jones
2021-03-18 12:39 ` [PATCH V5 2/2] backlight: qcom-wled: Correct the sync_toggle sequence Kiran Gunda
2021-03-23  9:40   ` Lee Jones

Linux-LEDs Archive on lore.kernel.org

Archives are clonable:
	git clone --mirror https://lore.kernel.org/linux-leds/0 linux-leds/git/0.git

	# If you have public-inbox 1.1+ installed, you may
	# initialize and index your mirror using the following commands:
	public-inbox-init -V2 linux-leds linux-leds/ https://lore.kernel.org/linux-leds \
		linux-leds@vger.kernel.org
	public-inbox-index linux-leds

Example config snippet for mirrors

Newsgroup available over NNTP:
	nntp://nntp.lore.kernel.org/org.kernel.vger.linux-leds


AGPL code for this site: git clone https://public-inbox.org/public-inbox.git