* [PATCH V4 1/3] mfd: Add support for UP board CPLD/FPGA
2023-05-11 9:49 [PATCH V4 0/3] Add support control UP board CPLD/FPGA pin control larry.lai
@ 2023-05-11 9:49 ` larry.lai
2023-05-25 10:16 ` Lee Jones
2023-05-11 9:49 ` [PATCH V4 2/3] pinctrl: Add support pin control " larry.lai
2023-05-11 9:49 ` [PATCH V4 3/3] leds: Add support for UP board CPLD onboard LEDS larry.lai
2 siblings, 1 reply; 6+ messages in thread
From: larry.lai @ 2023-05-11 9:49 UTC (permalink / raw)
To: lee, andriy.shevchenko, linus.walleij, pavel
Cc: linux-kernel, linux-gpio, linux-leds, GaryWang, musa.lin,
jack.chang, noah.hung, michael.wang, larry.lai
The UP Squared board <http://www.upboard.com> implements certain
features (pin control, onboard LEDs or CEC) through an on-board CPLD/FPGA.
This mfd driver implements the line protocol to read and write registers
from the FPGA through regmap. The register address map is also included.
The UP Boards provide a few I/O pin headers (for both GPIO and
functions), including a 40-pin Raspberry Pi compatible header.
This patch implements support for the FPGA-based pin controller that
manages direction and enable state for those header pins.
Partial support UP boards:
* UP core + CREX
* UP core + CRST02
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: larry.lai <larry.lai@yunjingtech.com>
---
RFC 2023/04/25 -> PATCH V4
(1) Fixed kernel test robot compiler warning.
(2) Remove mistakes with wrong Reviewed-by tags.
RFC 2022/11/23 -> RFC 2023/04/25
(1) Refer 2022/12/08 Andy Shevchenko review, cleaned up coding style
and addressed review comments.
PATCH V3 -> RFC 2022/11/23:
(1) Refer 2022/11/16 Lee Jones review, cleaned up coding style and
addressed review comments.
(2) Description on the UP Boards FPGA register read/write protocols
PATCH V2 -> V3:
(1) fixed kernel test robot compiler warning.
PATCH V1 -> V2:
(1) Synchronizing upboard github to rc2
(2) Refer 2022/10/31 Lee Jones review, fixed some of the issues.
---
drivers/mfd/Kconfig | 12 +
drivers/mfd/Makefile | 1 +
drivers/mfd/upboard-fpga.c | 526 +++++++++++++++++++++++++++++++
include/linux/mfd/upboard-fpga.h | 61 ++++
4 files changed, 600 insertions(+)
create mode 100644 drivers/mfd/upboard-fpga.c
create mode 100644 include/linux/mfd/upboard-fpga.h
diff --git a/drivers/mfd/Kconfig b/drivers/mfd/Kconfig
index abb58ab1a1a4..1041e937fc7a 100644
--- a/drivers/mfd/Kconfig
+++ b/drivers/mfd/Kconfig
@@ -2104,6 +2104,18 @@ config MFD_QCOM_PM8008
under it in the device tree. Additional drivers must be enabled in
order to use the functionality of the device.
+config MFD_INTEL_UPBOARD_FPGA
+ tristate "Support for the Intel platform foundation kit UP board FPGA"
+ select MFD_CORE
+ depends on X86 && ACPI
+ help
+ Select this option to enable the Intel AAEON UP and UP^2 on-board FPGA.
+ This is core driver for the UP board that implements certain (pin
+ control, onboard LEDs or CEC) through an on-board FPGA.
+
+ To compile this driver as a module, choose M here: the module will be
+ called upboard-fpga.
+
menu "Multimedia Capabilities Port drivers"
depends on ARCH_SA1100
diff --git a/drivers/mfd/Makefile b/drivers/mfd/Makefile
index 858cacf659d6..8374a05f6f43 100644
--- a/drivers/mfd/Makefile
+++ b/drivers/mfd/Makefile
@@ -250,6 +250,7 @@ obj-$(CONFIG_MFD_ALTERA_A10SR) += altera-a10sr.o
obj-$(CONFIG_MFD_ALTERA_SYSMGR) += altera-sysmgr.o
obj-$(CONFIG_MFD_STPMIC1) += stpmic1.o
obj-$(CONFIG_MFD_SUN4I_GPADC) += sun4i-gpadc.o
+obj-$(CONFIG_MFD_INTEL_UPBOARD_FPGA) += upboard-fpga.o
obj-$(CONFIG_MFD_STM32_LPTIMER) += stm32-lptimer.o
obj-$(CONFIG_MFD_STM32_TIMERS) += stm32-timers.o
diff --git a/drivers/mfd/upboard-fpga.c b/drivers/mfd/upboard-fpga.c
new file mode 100644
index 000000000000..a9a231e6d431
--- /dev/null
+++ b/drivers/mfd/upboard-fpga.c
@@ -0,0 +1,526 @@
+// SPDX-License-Identifier: GPL-2.0-only
+/*
+ * UP Board multi function device driver for control CPLD/FPGA to
+ * provide more GPIO driving power also provide CPLD LEDs and pin mux function
+ * recognize HID AANT0F00 ~ AAANT0F04 in ACPI name space
+ *
+ * Copyright (c) AAEON. All rights reserved.
+ *
+ * Author: Gary Wang <garywang@aaeon.com.tw>
+ *
+ */
+#include <linux/acpi.h>
+#include <linux/dmi.h>
+#include <linux/gpio/consumer.h>
+#include <linux/kernel.h>
+#include <linux/leds.h>
+#include <linux/mfd/core.h>
+#include <linux/mfd/upboard-fpga.h>
+#include <linux/module.h>
+#include <linux/platform_device.h>
+#include <linux/regmap.h>
+#include <linux/bits.h>
+#include <linux/err.h>
+
+struct upboard_fpga_data {
+ const struct regmap_config *cpld_config;
+ const struct mfd_cell *cells;
+ size_t ncells;
+};
+
+#define AAEON_MANUFACTURER_ID 0x01
+#define SUPPORTED_FW_MAJOR 0x0
+#define MENUFACTURER_ID_MASK GENMASK(7, 0)
+
+#define FIRMWARE_ID_BUILD_OFFSET (12)
+#define FIRMWARE_ID_MAJOR_OFFSET (8)
+#define FIRMWARE_ID_MINOR_OFFSET (4)
+#define FIRMWARE_ID_PATCH_OFFSET (0)
+#define FIRMWARE_ID_MASK GENMASK(3, 0)
+
+/*
+ * For UP Board Series FPGA register read/write protocols
+ * EMUTEX specs:
+ * D0 D1 D2 D3 D4 D5 D6 D7 D8 D9 .... D22 D23
+ * [RW][ address ][ DATA ]
+ *
+ * Read Sequence:
+ * ___ ____________________________________________________ _________
+ * clr: \_/ <--low-pulse does start the write-readback \_/<--start
+ * sequence with partital reset of internal new sequence
+ * registers but the CONF-REG.
+ * ____________________________________________________________________
+ * rst: _/ _ _ _ _ _ _ __ __ __ _
+ * stb: STB#1->_/1\_/2\_/3\_...._/7\_/8\_/9\_/10\_..../23\_/24\_/<-STB#25 edge
+ * is needed
+ * to ACK
+ * (D0 - D7 stb rising latch)
+ * data_in: D0 D1 D2 .... D6 D7 don't ........ care(DC)
+ * data_out: don't ...........care(DC) D8 D9 .... D22 D23
+ * (D8 - D23 stb falling latch)
+ * flag_Read: _________...._________
+ * __DC_ ____________...._________/ \_
+ * counter:
+ * [00]DC[00][01][02] ............[08][9][10]............[24][00]
+ * CONF-REG:
+ * [00] [ CONF-REG ]
+ * wreg:
+ * [00]DC[00][ wreg=SHFT(wreg) ][ADR][DATA][wreg=SHFT(wreg)]
+ * wreg2:
+ * [ (COPY)=ADDR ]
+ */
+static int upboard_fpga_read(void *context, unsigned int reg, unsigned int *val)
+{
+ struct upboard_fpga * const fpga = context;
+ int i;
+
+ gpiod_set_value(fpga->clear_gpio, 0);
+ gpiod_set_value(fpga->clear_gpio, 1);
+
+ reg |= UPFPGA_READ_FLAG;
+
+ for (i = UPFPGA_ADDRESS_SIZE; i >= 0; i--) {
+ gpiod_set_value(fpga->strobe_gpio, 0);
+ gpiod_set_value(fpga->datain_gpio, !!(reg & BIT(i)));
+ gpiod_set_value(fpga->strobe_gpio, 1);
+ }
+
+ gpiod_set_value(fpga->strobe_gpio, 0);
+ *val = 0;
+
+ for (i = UPFPGA_REGISTER_SIZE - 1; i >= 0; i--) {
+ gpiod_set_value(fpga->strobe_gpio, 1);
+ gpiod_set_value(fpga->strobe_gpio, 0);
+ *val |= gpiod_get_value(fpga->dataout_gpio) << i;
+ }
+
+ gpiod_set_value(fpga->strobe_gpio, 1);
+
+ return 0;
+}
+
+/*
+ * Write Sequence:
+ * ___ ____________________________________________________ _________
+ * clr: \_/ <--low-pulse does start the write-readback \_/<--start
+ * sequence with partital reset of internal new sequence
+ * registers but the CONF-REG.
+ * ____________________________________________________________________
+ * rst: _/ _ _ _ _ _ _ __ __ __ _
+ * stb: STB#1->_/1\_/2\_/3\_...._/7\_/8\_/9\_/10\_..../23\_/24\_/<-STB#25 edge
+ * is needed
+ * to ACK
+ * (D0 - D23 stb rising latch)
+ * data_in: D0 D1 D2 .... D6 D7 D8 D9 .... D22 D23
+ * data_out: don't ................................care (DC)
+ * flag_Read:
+ * __DC_ ____________....__________________________________
+ * counter:
+ * [00]DC[00][01][02] ............[08][9][10]............[24][00]
+ * wreg:
+ * [00]DC[00][wreg=SHFT(wreg)&dat_in ][SHFT(wreg)&dat_in][DAT]
+ * wreg2:
+ * [ (COPY)=ADDR ]
+ * CONF-REG:
+ * [00] [ CONF-REG = OLD VALUE ][CONF-REG=DAT]
+ */
+static int upboard_fpga_write(void *context, unsigned int reg, unsigned int val)
+{
+ struct upboard_fpga * const fpga = context;
+ int i;
+
+ gpiod_set_value(fpga->clear_gpio, 0);
+ gpiod_set_value(fpga->clear_gpio, 1);
+
+ for (i = UPFPGA_ADDRESS_SIZE; i >= 0; i--) {
+ gpiod_set_value(fpga->strobe_gpio, 0);
+ gpiod_set_value(fpga->datain_gpio, !!(reg & BIT(i)));
+ gpiod_set_value(fpga->strobe_gpio, 1);
+ }
+
+ gpiod_set_value(fpga->strobe_gpio, 0);
+
+ for (i = UPFPGA_REGISTER_SIZE - 1; i >= 0; i--) {
+ gpiod_set_value(fpga->datain_gpio, !!(val & BIT(i)));
+ gpiod_set_value(fpga->strobe_gpio, 1);
+ gpiod_set_value(fpga->strobe_gpio, 0);
+ }
+
+ gpiod_set_value(fpga->strobe_gpio, 1);
+
+ return 0;
+}
+
+static const struct regmap_range upboard_up_readable_ranges[] = {
+ regmap_reg_range(UPFPGA_REG_PLATFORM_ID, UPFPGA_REG_FIRMWARE_ID),
+ regmap_reg_range(UPFPGA_REG_FUNC_EN0, UPFPGA_REG_FUNC_EN0),
+ regmap_reg_range(UPFPGA_REG_GPIO_DIR0, UPFPGA_REG_GPIO_DIR1),
+};
+
+static const struct regmap_range upboard_up_writable_ranges[] = {
+ regmap_reg_range(UPFPGA_REG_FUNC_EN0, UPFPGA_REG_FUNC_EN0),
+ regmap_reg_range(UPFPGA_REG_GPIO_DIR0, UPFPGA_REG_GPIO_DIR1),
+};
+
+static const struct regmap_access_table upboard_up_readable_table = {
+ .yes_ranges = upboard_up_readable_ranges,
+ .n_yes_ranges = ARRAY_SIZE(upboard_up_readable_ranges),
+};
+
+static const struct regmap_access_table upboard_up_writable_table = {
+ .yes_ranges = upboard_up_writable_ranges,
+ .n_yes_ranges = ARRAY_SIZE(upboard_up_writable_ranges),
+};
+
+static const struct regmap_config upboard_up_regmap_config = {
+ .reg_bits = UPFPGA_ADDRESS_SIZE,
+ .val_bits = UPFPGA_REGISTER_SIZE,
+ .max_register = UPFPGA_REG_MAX,
+ .reg_read = upboard_fpga_read,
+ .reg_write = upboard_fpga_write,
+ .fast_io = false,
+ .cache_type = REGCACHE_RBTREE,
+ .rd_table = &upboard_up_readable_table,
+ .wr_table = &upboard_up_writable_table,
+};
+
+static struct upboard_led_data upboard_up_led_data[] = {
+ { .bit = 0, .colour = "yellow" },
+ { .bit = 1, .colour = "green" },
+ { .bit = 2, .colour = "red" },
+};
+
+static const struct mfd_cell upboard_up_mfd_cells[] = {
+ { .name = "upboard-pinctrl" },
+ MFD_CELL_BASIC("upboard-led", NULL, &upboard_up_led_data[0],
+ sizeof(*upboard_up_led_data), 0),
+ MFD_CELL_BASIC("upboard-led", NULL, &upboard_up_led_data[1],
+ sizeof(*upboard_up_led_data), 1),
+ MFD_CELL_BASIC("upboard-led", NULL, &upboard_up_led_data[2],
+ sizeof(*upboard_up_led_data), 2),
+};
+
+/* UP Squared 6000 EHL board */
+
+static const struct upboard_fpga_data upboard_up_fpga_data = {
+ .cpld_config = &upboard_up_regmap_config,
+ .cells = upboard_up_mfd_cells,
+ .ncells = ARRAY_SIZE(upboard_up_mfd_cells),
+};
+
+static const struct mfd_cell upboard_pinctrl_cells[] = {
+ { .name = "upboard-pinctrl" },
+};
+
+static const struct upboard_fpga_data upboard_pinctrl_data = {
+ .cpld_config = &upboard_up_regmap_config,
+ .cells = upboard_pinctrl_cells,
+ .ncells = ARRAY_SIZE(upboard_pinctrl_cells),
+};
+
+/* UP^2 board */
+static const struct regmap_range upboard_up2_readable_ranges[] = {
+ regmap_reg_range(UPFPGA_REG_PLATFORM_ID, UPFPGA_REG_FIRMWARE_ID),
+ regmap_reg_range(UPFPGA_REG_FUNC_EN0, UPFPGA_REG_FUNC_EN1),
+ regmap_reg_range(UPFPGA_REG_GPIO_EN0, UPFPGA_REG_GPIO_EN2),
+ regmap_reg_range(UPFPGA_REG_GPIO_DIR0, UPFPGA_REG_GPIO_DIR2),
+};
+
+static const struct regmap_range upboard_up2_writable_ranges[] = {
+ regmap_reg_range(UPFPGA_REG_FUNC_EN0, UPFPGA_REG_FUNC_EN1),
+ regmap_reg_range(UPFPGA_REG_GPIO_EN0, UPFPGA_REG_GPIO_EN2),
+ regmap_reg_range(UPFPGA_REG_GPIO_DIR0, UPFPGA_REG_GPIO_DIR2),
+};
+
+static const struct regmap_access_table upboard_up2_readable_table = {
+ .yes_ranges = upboard_up2_readable_ranges,
+ .n_yes_ranges = ARRAY_SIZE(upboard_up2_readable_ranges),
+};
+
+static const struct regmap_access_table upboard_up2_writable_table = {
+ .yes_ranges = upboard_up2_writable_ranges,
+ .n_yes_ranges = ARRAY_SIZE(upboard_up2_writable_ranges),
+};
+
+static const struct regmap_config upboard_up2_regmap_config = {
+ .reg_bits = UPFPGA_ADDRESS_SIZE,
+ .val_bits = UPFPGA_REGISTER_SIZE,
+ .max_register = UPFPGA_REG_MAX,
+ .reg_read = upboard_fpga_read,
+ .reg_write = upboard_fpga_write,
+ .fast_io = false,
+ .cache_type = REGCACHE_NONE,
+ .rd_table = &upboard_up2_readable_table,
+ .wr_table = &upboard_up2_writable_table,
+};
+
+static struct upboard_led_data upboard_up2_led_data[] = {
+ { .bit = 0, .colour = "blue" },
+ { .bit = 1, .colour = "yellow" },
+ { .bit = 2, .colour = "green" },
+ { .bit = 3, .colour = "red" },
+};
+
+static const struct mfd_cell upboard_up2_mfd_cells[] = {
+ { .name = "upboard-pinctrl" },
+ MFD_CELL_BASIC("upboard-led", NULL, &upboard_up2_led_data[0],
+ sizeof(*upboard_up2_led_data), 0),
+ MFD_CELL_BASIC("upboard-led", NULL, &upboard_up2_led_data[1],
+ sizeof(*upboard_up2_led_data), 1),
+ MFD_CELL_BASIC("upboard-led", NULL, &upboard_up2_led_data[2],
+ sizeof(*upboard_up2_led_data), 2),
+ MFD_CELL_BASIC("upboard-led", NULL, &upboard_up2_led_data[3],
+ sizeof(*upboard_up2_led_data), 3),
+};
+
+static const struct upboard_fpga_data upboard_up2_fpga_data = {
+ .cpld_config = &upboard_up2_regmap_config,
+ .cells = upboard_up2_mfd_cells,
+ .ncells = ARRAY_SIZE(upboard_up2_mfd_cells),
+};
+
+/* UP-CRST02 carrier board for UP Core */
+
+/* same MAX10 config as UP2, but same LED cells as UP1 */
+static const struct upboard_fpga_data upboard_upcore_crst02_fpga_data = {
+ .cpld_config = &upboard_up2_regmap_config,
+ .cells = upboard_up_mfd_cells,
+ .ncells = ARRAY_SIZE(upboard_up_mfd_cells),
+};
+
+static int __init upboard_fpga_gpio_init(struct upboard_fpga *fpga)
+{
+ enum gpiod_flags flags = fpga->uninitialised ? GPIOD_OUT_LOW : GPIOD_ASIS;
+
+ fpga->enable_gpio = devm_gpiod_get(fpga->dev, "enable", flags);
+ if (IS_ERR(fpga->enable_gpio))
+ return PTR_ERR(fpga->enable_gpio);
+
+ fpga->clear_gpio = devm_gpiod_get(fpga->dev, "clear", GPIOD_OUT_LOW);
+ if (IS_ERR(fpga->clear_gpio))
+ return PTR_ERR(fpga->clear_gpio);
+
+ fpga->strobe_gpio = devm_gpiod_get(fpga->dev, "strobe", GPIOD_OUT_LOW);
+ if (IS_ERR(fpga->strobe_gpio))
+ return PTR_ERR(fpga->strobe_gpio);
+
+ fpga->datain_gpio = devm_gpiod_get(fpga->dev, "datain", GPIOD_OUT_LOW);
+ if (IS_ERR(fpga->datain_gpio))
+ return PTR_ERR(fpga->datain_gpio);
+
+ fpga->dataout_gpio = devm_gpiod_get(fpga->dev, "dataout", GPIOD_IN);
+ if (IS_ERR(fpga->dataout_gpio))
+ return PTR_ERR(fpga->dataout_gpio);
+
+ /*
+ * The SoC pinctrl driver may not support reserving the GPIO line for
+ * FPGA reset without causing an undesired reset pulse. This will clear
+ * any settings on the FPGA, so only do it if we must.
+ * Reset GPIO defaults HIGH, get GPIO and set to LOW, then set back to
+ * HIGH as a pulse.
+ */
+ if (fpga->uninitialised) {
+ fpga->reset_gpio = devm_gpiod_get(fpga->dev, "reset", GPIOD_OUT_LOW);
+ if (IS_ERR(fpga->reset_gpio))
+ return PTR_ERR(fpga->reset_gpio);
+
+ gpiod_set_value(fpga->reset_gpio, 1);
+ }
+
+ gpiod_set_value(fpga->enable_gpio, 1);
+ fpga->uninitialised = false;
+
+ return 0;
+}
+
+/*
+ * This function is for debugging with user for showing firmware information.
+ */
+static int __init upboard_fpga_show_firmware_info(struct upboard_fpga *fpga)
+{
+ unsigned int platform_id, manufacturer_id;
+ unsigned int firmware_id, build, major, minor, patch;
+ int ret;
+
+ if (!fpga)
+ return -ENOMEM;
+
+ ret = regmap_read(fpga->regmap, UPFPGA_REG_PLATFORM_ID, &platform_id);
+ if (ret)
+ return ret;
+
+ manufacturer_id = platform_id & MENUFACTURER_ID_MASK;
+ if (manufacturer_id != AAEON_MANUFACTURER_ID) {
+ dev_err(fpga->dev,
+ "driver not compatible with custom FPGA FW from manufacturer id 0x%02x. Exiting",
+ manufacturer_id);
+
+ return -ENODEV;
+ }
+
+ ret = regmap_read(fpga->regmap, UPFPGA_REG_FIRMWARE_ID, &firmware_id);
+ if (ret)
+ return ret;
+
+ build = (firmware_id >> FIRMWARE_ID_BUILD_OFFSET) & FIRMWARE_ID_MASK;
+ major = (firmware_id >> FIRMWARE_ID_MAJOR_OFFSET) & FIRMWARE_ID_MASK;
+ minor = (firmware_id >> FIRMWARE_ID_MINOR_OFFSET) & FIRMWARE_ID_MASK;
+ patch = (firmware_id >> FIRMWARE_ID_PATCH_OFFSET) & FIRMWARE_ID_MASK;
+
+ if (major != SUPPORTED_FW_MAJOR) {
+ dev_err(fpga->dev, "unsupported FPGA FW v%u.%u.%u build 0x%02x",
+ major, minor, patch, build);
+
+ return -ENODEV;
+ }
+
+ dev_info(fpga->dev, "compatible FPGA FW v%u.%u.%u build 0x%02x",
+ major, minor, patch, build);
+
+ return 0;
+}
+
+/*
+ * MFD upboard-fpga is ACPI driver and can recognize the AANT ID from different
+ * kind of upboards. We get the LED GPIO initialized information from this
+ * then add led-upboard driver.
+ */
+int upboard_led_gpio_register(struct upboard_fpga *fpga)
+{
+ struct gpio_led blue_led, yellow_led, green_led, red_led;
+ struct gpio_desc *desc;
+ static struct gpio_led upboard_gpio_leds[4];
+ int leds = 0;
+ static struct gpio_led_platform_data upboard_gpio_led_platform_data;
+ static const struct mfd_cell upboard_gpio_led_cells[] = {
+ MFD_CELL_BASIC("leds-gpio", NULL,
+ &upboard_gpio_led_platform_data,
+ sizeof(upboard_gpio_led_platform_data), 0)
+ };
+ int ret;
+
+ desc = devm_gpiod_get(fpga->dev, "blue", GPIOD_OUT_LOW);
+ if (!IS_ERR(desc)) {
+ blue_led.name = "upboard:blue:";
+ blue_led.gpio = desc_to_gpio(desc);
+ blue_led.default_state = LEDS_GPIO_DEFSTATE_KEEP;
+ upboard_gpio_leds[leds++] = blue_led;
+ devm_gpiod_put(fpga->dev, desc);
+ }
+ desc = devm_gpiod_get(fpga->dev, "yellow", GPIOD_OUT_LOW);
+ if (!IS_ERR(desc)) {
+ yellow_led.name = "upboard:yellow:";
+ yellow_led.gpio = desc_to_gpio(desc);
+ yellow_led.default_state = LEDS_GPIO_DEFSTATE_KEEP;
+ upboard_gpio_leds[leds++] = yellow_led;
+ devm_gpiod_put(fpga->dev, desc);
+ }
+ desc = devm_gpiod_get(fpga->dev, "green", GPIOD_OUT_LOW);
+ if (!IS_ERR(desc)) {
+ green_led.name = "upboard:green:";
+ green_led.gpio = desc_to_gpio(desc);
+ green_led.default_state = LEDS_GPIO_DEFSTATE_KEEP;
+ upboard_gpio_leds[leds++] = green_led;
+ devm_gpiod_put(fpga->dev, desc);
+ }
+ desc = devm_gpiod_get(fpga->dev, "red", GPIOD_OUT_LOW);
+ if (!IS_ERR(desc)) {
+ red_led.name = "upboard:red:";
+ red_led.gpio = desc_to_gpio(desc);
+ red_led.default_state = LEDS_GPIO_DEFSTATE_KEEP;
+ upboard_gpio_leds[leds++] = red_led;
+ devm_gpiod_put(fpga->dev, desc);
+ }
+
+ /* no LEDs */
+ if (leds == 0)
+ return 0;
+
+ upboard_gpio_led_platform_data.num_leds = leds;
+ upboard_gpio_led_platform_data.leds = upboard_gpio_leds;
+
+ ret = devm_mfd_add_devices(fpga->dev, PLATFORM_DEVID_AUTO,
+ upboard_gpio_led_cells,
+ ARRAY_SIZE(upboard_gpio_led_cells),
+ NULL, 0, NULL);
+ if (ret) {
+ dev_err(fpga->dev, "Failed to add GPIO LEDs,%d", ret);
+ return ret;
+ }
+
+ return 0;
+}
+
+static const struct acpi_device_id upboard_fpga_acpi_match[] = {
+ { "AANT0000", (kernel_ulong_t)&upboard_pinctrl_data },
+ { "AANT0F00", (kernel_ulong_t)&upboard_up_fpga_data },
+ { "AANT0F01", (kernel_ulong_t)&upboard_up2_fpga_data },
+ { "AANT0F02", (kernel_ulong_t)&upboard_up_fpga_data },
+ { "AANT0F03", (kernel_ulong_t)&upboard_upcore_crst02_fpga_data },
+ { "AANT0F04", (kernel_ulong_t)&upboard_up_fpga_data },
+ { }
+};
+MODULE_DEVICE_TABLE(acpi, upboard_fpga_acpi_match);
+
+static int __init upboard_fpga_probe(struct platform_device *pdev)
+{
+ struct upboard_fpga *fpga;
+ const struct acpi_device_id *id;
+ const struct upboard_fpga_data *fpga_data;
+ int ret;
+ struct device *dev = &pdev->dev;
+
+ id = acpi_match_device(upboard_fpga_acpi_match, dev);
+ if (!id)
+ return -ENODEV;
+
+ fpga_data = (const struct upboard_fpga_data *) id->driver_data;
+
+ fpga = devm_kzalloc(dev, sizeof(*fpga), GFP_KERNEL);
+ if (!fpga)
+ return -ENOMEM;
+
+ platform_set_drvdata(pdev, fpga);
+ fpga->regmap = devm_regmap_init(dev, NULL, fpga, fpga_data->cpld_config);
+ fpga->cpld_config = (struct regmap_config *)fpga_data->cpld_config;
+
+ if (IS_ERR(fpga->regmap))
+ return PTR_ERR(fpga->regmap);
+
+ ret = upboard_fpga_gpio_init(fpga);
+ if (ret) {
+ /*
+ * This is for compatiable with some upboards w/o FPGA firmware,
+ * so just showing debug info and do not return directly.
+ */
+ dev_warn(dev, "Failed to initialize FPGA common GPIOs: %d", ret);
+ } else {
+ upboard_fpga_show_firmware_info(fpga);
+ }
+
+ /* register GPIO LEDs */
+ ret = upboard_led_gpio_register(fpga);
+ if (ret) {
+ /*
+ * This is for compatiable with some upboards w/o LEDs.
+ */
+ dev_warn(dev, "Failed to register LEDs: %d", ret);
+ }
+
+ return devm_mfd_add_devices(dev, PLATFORM_DEVID_AUTO,
+ fpga_data->cells,
+ fpga_data->ncells,
+ NULL, 0, NULL);
+}
+
+static struct platform_driver upboard_fpga_driver = {
+ .driver = {
+ .name = "upboard-fpga",
+ .acpi_match_table = upboard_fpga_acpi_match,
+ },
+};
+module_platform_driver_probe(upboard_fpga_driver, upboard_fpga_probe);
+
+MODULE_AUTHOR("Gary Wang <garywang@aaeon.com.tw>");
+MODULE_DESCRIPTION("UP Board CPLD/FPGA driver");
+MODULE_LICENSE("GPL v2");
diff --git a/include/linux/mfd/upboard-fpga.h b/include/linux/mfd/upboard-fpga.h
new file mode 100644
index 000000000000..1fa073e5c53c
--- /dev/null
+++ b/include/linux/mfd/upboard-fpga.h
@@ -0,0 +1,61 @@
+/* SPDX-License-Identifier: GPL-2.0-only */
+/*
+ * UP Board CPLD/FPGA driver
+ *
+ * Copyright (c) AAEON. All rights reserved.
+ *
+ * Author: Gary Wang <garywang@aaeon.com.tw>
+ *
+ */
+
+#ifndef __LINUX_MFD_UPBOARD_FPGA_H
+#define __LINUX_MFD_UPBOARD_FPGA_H
+
+#include <linux/device.h>
+#include <linux/regmap.h>
+
+/* CPLD/FPGA protocol version */
+#define UPFPGA_PROTOCOL_V1_HRV 1
+#define UPFPGA_PROTOCOL_V2_HRV 2
+
+#define UPFPGA_ADDRESS_SIZE 7
+#define UPFPGA_REGISTER_SIZE 16
+
+#define UPFPGA_READ_FLAG (1 << UPFPGA_ADDRESS_SIZE)
+
+enum upboard_fpgareg {
+ UPFPGA_REG_PLATFORM_ID = 0x10,
+ UPFPGA_REG_FIRMWARE_ID = 0x11,
+ UPFPGA_REG_FUNC_EN0 = 0x20,
+ UPFPGA_REG_FUNC_EN1 = 0x21,
+ UPFPGA_REG_GPIO_EN0 = 0x30,
+ UPFPGA_REG_GPIO_EN1 = 0x31,
+ UPFPGA_REG_GPIO_EN2 = 0x32,
+ UPFPGA_REG_GPIO_DIR0 = 0x40,
+ UPFPGA_REG_GPIO_DIR1 = 0x41,
+ UPFPGA_REG_GPIO_DIR2 = 0x42,
+ UPFPGA_REG_MAX,
+};
+
+struct upboard_fpga {
+ struct device *dev;
+ struct regmap *regmap;
+ struct regmap_config *cpld_config;
+ struct gpio_desc *enable_gpio;
+ struct gpio_desc *reset_gpio;
+ struct gpio_desc *clear_gpio;
+ struct gpio_desc *strobe_gpio;
+ struct gpio_desc *datain_gpio;
+ struct gpio_desc *dataout_gpio;
+ bool uninitialised;
+};
+
+struct upboard_led_data {
+ unsigned int bit;
+ const char *colour;
+};
+
+bool regmap_check_writeable(struct upboard_fpga *fpga, unsigned int reg);
+int upboard_led_gpio_register(struct upboard_fpga *fpga);
+
+#endif /* __LINUX_MFD_UPBOARD_FPGA_H */
--
2.17.1
^ permalink raw reply related [flat|nested] 6+ messages in thread* [PATCH V4 2/3] pinctrl: Add support pin control for UP board CPLD/FPGA
2023-05-11 9:49 [PATCH V4 0/3] Add support control UP board CPLD/FPGA pin control larry.lai
2023-05-11 9:49 ` [PATCH V4 1/3] mfd: Add support for UP board CPLD/FPGA larry.lai
@ 2023-05-11 9:49 ` larry.lai
2023-05-11 17:27 ` kernel test robot
2023-05-11 9:49 ` [PATCH V4 3/3] leds: Add support for UP board CPLD onboard LEDS larry.lai
2 siblings, 1 reply; 6+ messages in thread
From: larry.lai @ 2023-05-11 9:49 UTC (permalink / raw)
To: lee, andriy.shevchenko, linus.walleij, pavel
Cc: linux-kernel, linux-gpio, linux-leds, GaryWang, musa.lin,
jack.chang, noah.hung, michael.wang, larry.lai
The UP Squared board <http://www.upboard.com> implements certain
features (pin control) through an on-board FPGA.
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: larry.lai <larry.lai@yunjingtech.com>
---
RFC 2023/04/25 -> PATCH V4
(1) Fixed kernel test robot compiler warning.
(2) Remove mistakes with wrong Reviewed-by tags.
RFC 2022/11/23 -> RFC 2023/04/25
(1) Refer 2022/12/08 Andy Shevchenko review, cleaned up coding style and
addressed review comments.
PATCH V3 -> RFC 2022/11/23:
(1) Refer 2022/11/09 Linus Walleij review, cleaned up coding style and
addressed review comments.
PATCH V2 -> V3:
There's no change.
PATCH V1 -> V2:
(1) Synchronized with upboard github to rc2
(2) Refer 2022/10/19 Mark Brown and Andy Shevchenko review, we removed
the regmap and acpi patches and implement in upboard pinctrl driver.
(3) Refer 2022/10/19 Andy Shevchenko review, fixed the coding style
issues, removed using gpio_xxxx API and removed including <linux/gpio.h>.
---
drivers/pinctrl/Kconfig | 14 +
drivers/pinctrl/Makefile | 1 +
drivers/pinctrl/pinctrl-upboard.c | 1296 +++++++++++++++++++++++++++++
3 files changed, 1311 insertions(+)
create mode 100644 drivers/pinctrl/pinctrl-upboard.c
diff --git a/drivers/pinctrl/Kconfig b/drivers/pinctrl/Kconfig
index 1cf74b0c42e5..cc8dae75289b 100644
--- a/drivers/pinctrl/Kconfig
+++ b/drivers/pinctrl/Kconfig
@@ -483,6 +483,20 @@ config PINCTRL_THUNDERBAY
rate control and direction control. This module will be
called as pinctrl-thunderbay.
+config PINCTRL_UPBOARD
+ tristate "UP board FPGA pin controller"
+ depends on (X86 && ACPI) || COMPILE_TEST
+ depends on MFD_INTEL_UPBOARD_FPGA
+ select GENERIC_PINCONF
+ select PINMUX
+ select PINCONF
+ help
+ Pin controller for the FPGA GPIO lines on UP boards. Due to the
+ hardware layout, these are meant to be controlled in tandem with their
+ corresponding Intel SoC GPIOs.
+ To compile this driver as a module, choose M here: the module
+ will be called pinctrl-upboard.
+
config PINCTRL_ZYNQ
bool "Pinctrl driver for Xilinx Zynq"
depends on ARCH_ZYNQ
diff --git a/drivers/pinctrl/Makefile b/drivers/pinctrl/Makefile
index e76f5cdc64b0..c366706d36e7 100644
--- a/drivers/pinctrl/Makefile
+++ b/drivers/pinctrl/Makefile
@@ -48,6 +48,7 @@ obj-$(CONFIG_PINCTRL_STMFX) += pinctrl-stmfx.o
obj-$(CONFIG_PINCTRL_SX150X) += pinctrl-sx150x.o
obj-$(CONFIG_PINCTRL_TB10X) += pinctrl-tb10x.o
obj-$(CONFIG_PINCTRL_THUNDERBAY) += pinctrl-thunderbay.o
+obj-$(CONFIG_PINCTRL_UPBOARD) += pinctrl-upboard.o
obj-$(CONFIG_PINCTRL_ZYNQMP) += pinctrl-zynqmp.o
obj-$(CONFIG_PINCTRL_ZYNQ) += pinctrl-zynq.o
diff --git a/drivers/pinctrl/pinctrl-upboard.c b/drivers/pinctrl/pinctrl-upboard.c
new file mode 100644
index 000000000000..c9576bc80e79
--- /dev/null
+++ b/drivers/pinctrl/pinctrl-upboard.c
@@ -0,0 +1,1296 @@
+// SPDX-License-Identifier: GPL-2.0-only
+/*
+ * UP Board HAT pin controller driver
+ * remapping native pin to RPI pin and set CPLD pin dir
+ *
+ * Copyright (c) AAEON. All rights reserved.
+ *
+ * Authors: Gary Wang <garywang@aaeon.com.tw>
+ *
+ */
+
+#include <linux/acpi.h>
+#include <linux/dmi.h>
+#include <linux/gpio/consumer.h>
+#include <linux/gpio/driver.h>
+#include <linux/kernel.h>
+#include <linux/mfd/upboard-fpga.h>
+#include <linux/module.h>
+#include <linux/pinctrl/pinctrl.h>
+#include <linux/pinctrl/pinmux.h>
+#include <linux/platform_device.h>
+#include <linux/regmap.h>
+#include <linux/interrupt.h>
+#include <linux/string.h>
+#include <linux/slab.h>
+
+#include "core.h"
+#include "intel/pinctrl-intel.h"
+
+/* Offset from regs */
+#define REVID 0x000
+#define REVID_SHIFT 16
+#define REVID_MASK GENMASK(31, 16)
+#define PADBAR 0x00c
+
+/* Offset from pad_regs */
+#define PADCFG0 0x000
+#define PADCFG0_RXEVCFG_SHIFT 25
+#define PADCFG0_RXEVCFG_MASK GENMASK(26, 25)
+#define PADCFG0_RXEVCFG_LEVEL 0
+#define PADCFG0_RXEVCFG_EDGE 1
+#define PADCFG0_RXEVCFG_DISABLED 2
+#define PADCFG0_RXEVCFG_EDGE_BOTH 3
+#define PADCFG0_PREGFRXSEL BIT(24)
+#define PADCFG0_RXINV BIT(23)
+#define PADCFG0_GPIROUTIOXAPIC BIT(20)
+#define PADCFG0_GPIROUTSCI BIT(19)
+#define PADCFG0_GPIROUTSMI BIT(18)
+#define PADCFG0_GPIROUTNMI BIT(17)
+#define PADCFG0_PMODE_SHIFT 10
+#define PADCFG0_PMODE_MASK GENMASK(13, 10)
+#define PADCFG0_PMODE_GPIO 0
+#define PADCFG0_GPIORXDIS BIT(9)
+#define PADCFG0_GPIOTXDIS BIT(8)
+#define PADCFG0_GPIORXSTATE BIT(1)
+#define PADCFG0_GPIOTXSTATE BIT(0)
+
+#define PADCFG1 0x004
+#define PADCFG1_TERM_UP BIT(13)
+#define PADCFG1_TERM_SHIFT 10
+#define PADCFG1_TERM_MASK GENMASK(12, 10)
+#define PADCFG1_TERM_20K BIT(2)
+#define PADCFG1_TERM_5K BIT(1)
+#define PADCFG1_TERM_1K BIT(0)
+#define PADCFG1_TERM_833 (BIT(1) | BIT(0))
+
+#define PADCFG2 0x008
+#define PADCFG2_DEBEN BIT(0)
+#define PADCFG2_DEBOUNCE_SHIFT 1
+#define PADCFG2_DEBOUNCE_MASK GENMASK(4, 1)
+
+#define DEBOUNCE_PERIOD_NSEC 31250
+
+/* Additional features supported by the hardware */
+#define PINCTRL_FEATURE_DEBOUNCE BIT(0)
+#define PINCTRL_FEATURE_1K_PD BIT(1)
+
+#define BOARD_UP_CHT01 0
+#define BOARD_UP_APL01 1
+#define BOARD_UP_UPCORE 2
+#define BOARD_UP_CORE_PLUS 3
+#define BOARD_AIOT_IP6801 4
+#define BOARD_UP_WHL01 5
+#define BOARD_UP_ISH 7
+#define BOARD_UPN_APL 8
+#define BOARD_UP_APL03 9
+#define BOARD_UPX_WHLite 10
+#define BOARD_UPX_TGL 11
+#define BOARD_UPX_EDGE_WHL2 12
+#define BOARD_UPN_EHL01 13
+#define BOARD_UPS_EHL01 14
+#define BOARD_UPX_ADLP01 15
+#define BOARD_UPN_ADLN01 16
+#define BOARD_UPS_ADLP01 15
+
+struct upboard_pin {
+ struct regmap_field *funcbit;
+ struct regmap_field *enbit;
+ struct regmap_field *dirbit;
+ /* native pin controllers: number, base, irq */
+ unsigned int gpio;
+ unsigned int base;
+ int irq;
+ void __iomem *regs;
+};
+
+struct upboard_pinctrl {
+ struct gpio_chip chip;
+ struct device *dev;
+ struct pinctrl_dev *pctldev;
+ struct pinctrl_desc *pctldesc;
+ struct upboard_pin *pins;
+ struct regmap *regmap;
+ const unsigned int *rpi_mapping;
+ int ident;
+};
+
+enum upboard_func0_fpgabit {
+ UPFPGA_I2C0_EN = 8,
+ UPFPGA_I2C1_EN = 9,
+ UPFPGA_CEC0_EN = 12,
+ UPFPGA_ADC0_EN = 14,
+};
+
+static const struct reg_field upboard_i2c0_reg =
+ REG_FIELD(UPFPGA_REG_FUNC_EN0, UPFPGA_I2C0_EN, UPFPGA_I2C0_EN);
+
+static const struct reg_field upboard_i2c1_reg =
+ REG_FIELD(UPFPGA_REG_FUNC_EN0, UPFPGA_I2C1_EN, UPFPGA_I2C1_EN);
+
+static const struct reg_field upboard_adc0_reg =
+ REG_FIELD(UPFPGA_REG_FUNC_EN0, UPFPGA_ADC0_EN, UPFPGA_ADC0_EN);
+
+/* Pin group information */
+struct upboard_pingroup {
+ const char *name;
+ const unsigned int *pins;
+ size_t npins;
+};
+
+/* Pin function information */
+struct upboard_function {
+ const char *name;
+ const char * const *groups;
+ size_t ngroups;
+};
+
+#define UPBOARD_BIT_TO_PIN(r, bit) \
+ ((r) * UPFPGA_REGISTER_SIZE + (bit))
+
+/*
+ * UP board data
+ */
+
+#define UPBOARD_UP_BIT_TO_PIN(r, id) (UPBOARD_BIT_TO_PIN(r, UPFPGA_UP_##id))
+
+#define UPBOARD_UP_PIN_ANON(r, bit) \
+ { \
+ .number = UPBOARD_BIT_TO_PIN(r, bit), \
+ }
+
+#define UPBOARD_UP_PIN_NAME(r, id) \
+ { \
+ .number = UPBOARD_UP_BIT_TO_PIN(r, id), \
+ .name = #id, \
+ }
+
+#define UPBOARD_UP_PIN_FUNC(r, id, data) \
+ { \
+ .number = UPBOARD_UP_BIT_TO_PIN(r, id), \
+ .name = #id, \
+ .drv_data = (void *)(data), \
+ }
+
+#define UPBOARD_PIN_GROUP(n, p) \
+ { \
+ .name = (n), \
+ .pins = (p), \
+ .npins = ARRAY_SIZE((p)), \
+ }
+
+#define FUNCTION(n, g) \
+ { \
+ .name = (n), \
+ .groups = (g), \
+ .ngroups = ARRAY_SIZE((g)), \
+ }
+
+enum upboard_up_reg1_fpgabit {
+ UPFPGA_UP_I2C1_SDA,
+ UPFPGA_UP_I2C1_SCL,
+ UPFPGA_UP_ADC0,
+ UPFPGA_UP_GPIO17,
+ UPFPGA_UP_GPIO27,
+ UPFPGA_UP_GPIO22,
+ UPFPGA_UP_SPI_MOSI,
+ UPFPGA_UP_SPI_MISO,
+ UPFPGA_UP_SPI_CLK,
+ UPFPGA_UP_I2C0_SDA,
+ UPFPGA_UP_GPIO5,
+ UPFPGA_UP_GPIO6,
+ UPFPGA_UP_PWM1,
+ UPFPGA_UP_I2S_FRM,
+ UPFPGA_UP_GPIO26,
+ UPFPGA_UP_UART1_TX,
+};
+
+enum upboard_up_reg2_fpgabit {
+ UPFPGA_UP_UART1_RX,
+ UPFPGA_UP_I2S_CLK,
+ UPFPGA_UP_GPIO23,
+ UPFPGA_UP_GPIO24,
+ UPFPGA_UP_GPIO25,
+ UPFPGA_UP_SPI_CS0,
+ UPFPGA_UP_SPI_CS1,
+ UPFPGA_UP_I2C0_SCL,
+ UPFPGA_UP_PWM0,
+ UPFPGA_UP_GPIO16,
+ UPFPGA_UP_I2S_DIN,
+ UPFPGA_UP_I2S_DOUT,
+};
+
+#define UPFPGA_UP_UART1_RTS UPFPGA_UP_GPIO17
+#define UPFPGA_UP_UART1_CTS UPFPGA_UP_GPIO16
+
+static struct pinctrl_pin_desc upboard_up_pins[] = {
+ UPBOARD_UP_PIN_FUNC(0, I2C1_SDA, &upboard_i2c1_reg),
+ UPBOARD_UP_PIN_FUNC(0, I2C1_SCL, &upboard_i2c1_reg),
+ UPBOARD_UP_PIN_FUNC(0, ADC0, &upboard_adc0_reg),
+ UPBOARD_UP_PIN_NAME(0, UART1_RTS),
+ UPBOARD_UP_PIN_NAME(0, GPIO27),
+ UPBOARD_UP_PIN_NAME(0, GPIO22),
+ UPBOARD_UP_PIN_NAME(0, SPI_MOSI),
+ UPBOARD_UP_PIN_NAME(0, SPI_MISO),
+ UPBOARD_UP_PIN_NAME(0, SPI_CLK),
+ UPBOARD_UP_PIN_FUNC(0, I2C0_SDA, &upboard_i2c0_reg),
+ UPBOARD_UP_PIN_NAME(0, GPIO5),
+ UPBOARD_UP_PIN_NAME(0, GPIO6),
+ UPBOARD_UP_PIN_NAME(0, PWM1),
+ UPBOARD_UP_PIN_NAME(0, I2S_FRM),
+ UPBOARD_UP_PIN_NAME(0, GPIO26),
+ UPBOARD_UP_PIN_NAME(0, UART1_TX),
+ /* register 1 */
+ UPBOARD_UP_PIN_NAME(1, UART1_RX),
+ UPBOARD_UP_PIN_NAME(1, I2S_CLK),
+ UPBOARD_UP_PIN_NAME(1, GPIO23),
+ UPBOARD_UP_PIN_NAME(1, GPIO24),
+ UPBOARD_UP_PIN_NAME(1, GPIO25),
+ UPBOARD_UP_PIN_NAME(1, SPI_CS0),
+ UPBOARD_UP_PIN_NAME(1, SPI_CS1),
+ UPBOARD_UP_PIN_FUNC(1, I2C0_SCL, &upboard_i2c0_reg),
+ UPBOARD_UP_PIN_NAME(1, PWM0),
+ UPBOARD_UP_PIN_NAME(1, UART1_CTS),
+ UPBOARD_UP_PIN_NAME(1, I2S_DIN),
+ UPBOARD_UP_PIN_NAME(1, I2S_DOUT),
+};
+
+static const unsigned int upboard_up_rpi_mapping[] = {
+ UPBOARD_UP_BIT_TO_PIN(0, I2C0_SDA),
+ UPBOARD_UP_BIT_TO_PIN(1, I2C0_SCL),
+ UPBOARD_UP_BIT_TO_PIN(0, I2C1_SDA),
+ UPBOARD_UP_BIT_TO_PIN(0, I2C1_SCL),
+ UPBOARD_UP_BIT_TO_PIN(0, ADC0),
+ UPBOARD_UP_BIT_TO_PIN(0, GPIO5),
+ UPBOARD_UP_BIT_TO_PIN(0, GPIO6),
+ UPBOARD_UP_BIT_TO_PIN(1, SPI_CS1),
+ UPBOARD_UP_BIT_TO_PIN(1, SPI_CS0),
+ UPBOARD_UP_BIT_TO_PIN(0, SPI_MISO),
+ UPBOARD_UP_BIT_TO_PIN(0, SPI_MOSI),
+ UPBOARD_UP_BIT_TO_PIN(0, SPI_CLK),
+ UPBOARD_UP_BIT_TO_PIN(1, PWM0),
+ UPBOARD_UP_BIT_TO_PIN(0, PWM1),
+ UPBOARD_UP_BIT_TO_PIN(0, UART1_TX),
+ UPBOARD_UP_BIT_TO_PIN(1, UART1_RX),
+ UPBOARD_UP_BIT_TO_PIN(1, GPIO16),
+ UPBOARD_UP_BIT_TO_PIN(0, GPIO17),
+ UPBOARD_UP_BIT_TO_PIN(1, I2S_CLK),
+ UPBOARD_UP_BIT_TO_PIN(0, I2S_FRM),
+ UPBOARD_UP_BIT_TO_PIN(1, I2S_DIN),
+ UPBOARD_UP_BIT_TO_PIN(1, I2S_DOUT),
+ UPBOARD_UP_BIT_TO_PIN(0, GPIO22),
+ UPBOARD_UP_BIT_TO_PIN(1, GPIO23),
+ UPBOARD_UP_BIT_TO_PIN(1, GPIO24),
+ UPBOARD_UP_BIT_TO_PIN(1, GPIO25),
+ UPBOARD_UP_BIT_TO_PIN(0, GPIO26),
+ UPBOARD_UP_BIT_TO_PIN(0, GPIO27),
+};
+
+static const unsigned int uart1_pins[] = { 14, 15, 16, 17 };
+static const unsigned int uart2_pins[] = { 25, 27 };
+static const unsigned int i2c0_pins[] = { 0, 1 };
+static const unsigned int i2c1_pins[] = { 2, 3 };
+static const unsigned int spi2_pins[] = { 8, 9, 10, 11 };
+static const unsigned int i2s0_pins[] = { 18, 19, 20, 21 };
+static const unsigned int pwm0_pins[] = { 12 };
+static const unsigned int pwm1_pins[] = { 13 };
+static const unsigned int adc0_pins[] = { 4 };
+
+static const struct upboard_pingroup __attribute__((unused)) pin_groups[] = {
+ UPBOARD_PIN_GROUP("uart1_grp", uart1_pins),
+ UPBOARD_PIN_GROUP("uart2_grp", uart2_pins),
+ UPBOARD_PIN_GROUP("i2c0_grp", i2c0_pins),
+ UPBOARD_PIN_GROUP("i2c1_grp", i2c1_pins),
+ UPBOARD_PIN_GROUP("spi2_grp", spi2_pins),
+ UPBOARD_PIN_GROUP("i2s0_grp", i2s0_pins),
+ UPBOARD_PIN_GROUP("pwm0_grp", pwm0_pins),
+ UPBOARD_PIN_GROUP("pwm1_grp", pwm1_pins),
+ UPBOARD_PIN_GROUP("adc0_grp", adc0_pins),
+};
+
+static const char * const uart1_groups[] = { "uart1_grp" };
+static const char * const uart2_groups[] = { "uart2_grp" };
+static const char * const i2c0_groups[] = { "i2c0_grp" };
+static const char * const i2c1_groups[] = { "i2c1_grp" };
+static const char * const spi2_groups[] = { "spi2_grp" };
+static const char * const i2s0_groups[] = { "i2s0_grp" };
+static const char * const pwm0_groups[] = { "pwm0_grp" };
+static const char * const pwm1_groups[] = { "pwm1_grp" };
+static const char * const adc0_groups[] = { "adc0_grp" };
+
+static const struct upboard_function __attribute__((unused)) pin_functions[] = {
+ FUNCTION("uart1", uart1_groups),
+ FUNCTION("uart2", uart2_groups),
+ FUNCTION("i2c0", i2c0_groups),
+ FUNCTION("i2c1", i2c1_groups),
+ FUNCTION("spi2", spi2_groups),
+ FUNCTION("i2s0", i2s0_groups),
+ FUNCTION("pwm0", pwm0_groups),
+ FUNCTION("pwm1", pwm1_groups),
+ FUNCTION("adc0", adc0_groups),
+};
+
+/*
+ * UP^2 board data
+ */
+
+#define UPBOARD_UP2_BIT_TO_PIN(r, id) (UPBOARD_BIT_TO_PIN(r, UPFPGA_UP2_##id))
+
+#define UPBOARD_UP2_PIN_ANON(r, bit) \
+ { \
+ .number = UPBOARD_BIT_TO_PIN(r, bit), \
+ .name = "NONAME", \
+ }
+
+#define UPBOARD_UP2_PIN_NAME(r, id) \
+ { \
+ .number = UPBOARD_UP2_BIT_TO_PIN(r, id), \
+ .name = #id, \
+ }
+
+#define UPBOARD_UP2_PIN_FUNC(r, id, data) \
+ { \
+ .number = UPBOARD_UP2_BIT_TO_PIN(r, id), \
+ .name = #id, \
+ .drv_data = (void *)(data), \
+ }
+
+enum upboard_up2_reg0_fpgabit {
+ UPFPGA_UP2_UART1_TXD,
+ UPFPGA_UP2_UART1_RXD,
+ UPFPGA_UP2_UART1_RTS,
+ UPFPGA_UP2_UART1_CTS,
+ UPFPGA_UP2_GPIO3,
+ UPFPGA_UP2_GPIO5,
+ UPFPGA_UP2_GPIO6,
+ UPFPGA_UP2_GPIO11,
+ UPFPGA_UP2_EXHAT_LVDS1n,
+ UPFPGA_UP2_EXHAT_LVDS1p,
+ UPFPGA_UP2_SPI2_TXD,
+ UPFPGA_UP2_SPI2_RXD,
+ UPFPGA_UP2_SPI2_FS1,
+ UPFPGA_UP2_SPI2_FS0,
+ UPFPGA_UP2_SPI2_CLK,
+ UPFPGA_UP2_SPI1_TXD,
+};
+
+enum upboard_up2_reg1_fpgabit {
+ UPFPGA_UP2_SPI1_RXD,
+ UPFPGA_UP2_SPI1_FS1,
+ UPFPGA_UP2_SPI1_FS0,
+ UPFPGA_UP2_SPI1_CLK,
+ UPFPGA_UP2_BIT20,
+ UPFPGA_UP2_BIT21,
+ UPFPGA_UP2_BIT22,
+ UPFPGA_UP2_BIT23,
+ UPFPGA_UP2_PWM1,
+ UPFPGA_UP2_PWM0,
+ UPFPGA_UP2_EXHAT_LVDS0n,
+ UPFPGA_UP2_EXHAT_LVDS0p,
+ UPFPGA_UP2_I2C0_SCL,
+ UPFPGA_UP2_I2C0_SDA,
+ UPFPGA_UP2_I2C1_SCL,
+ UPFPGA_UP2_I2C1_SDA,
+};
+
+enum upboard_up2_reg2_fpgabit {
+ UPFPGA_UP2_EXHAT_LVDS3n,
+ UPFPGA_UP2_EXHAT_LVDS3p,
+ UPFPGA_UP2_EXHAT_LVDS4n,
+ UPFPGA_UP2_EXHAT_LVDS4p,
+ UPFPGA_UP2_EXHAT_LVDS5n,
+ UPFPGA_UP2_EXHAT_LVDS5p,
+ UPFPGA_UP2_I2S_SDO,
+ UPFPGA_UP2_I2S_SDI,
+ UPFPGA_UP2_I2S_WS_SYNC,
+ UPFPGA_UP2_I2S_BCLK,
+ UPFPGA_UP2_EXHAT_LVDS6n,
+ UPFPGA_UP2_EXHAT_LVDS6p,
+ UPFPGA_UP2_EXHAT_LVDS7n,
+ UPFPGA_UP2_EXHAT_LVDS7p,
+ UPFPGA_UP2_EXHAT_LVDS2n,
+ UPFPGA_UP2_EXHAT_LVDS2p,
+};
+
+static struct pinctrl_pin_desc upboard_up2_pins[] = {
+ UPBOARD_UP2_PIN_NAME(0, UART1_TXD),
+ UPBOARD_UP2_PIN_NAME(0, UART1_RXD),
+ UPBOARD_UP2_PIN_NAME(0, UART1_RTS),
+ UPBOARD_UP2_PIN_NAME(0, UART1_CTS),
+ UPBOARD_UP2_PIN_NAME(0, GPIO3),
+ UPBOARD_UP2_PIN_NAME(0, GPIO5),
+ UPBOARD_UP2_PIN_NAME(0, GPIO6),
+ UPBOARD_UP2_PIN_NAME(0, GPIO11),
+ UPBOARD_UP2_PIN_NAME(0, EXHAT_LVDS1n),
+ UPBOARD_UP2_PIN_NAME(0, EXHAT_LVDS1p),
+ UPBOARD_UP2_PIN_NAME(0, SPI2_TXD),
+ UPBOARD_UP2_PIN_NAME(0, SPI2_RXD),
+ UPBOARD_UP2_PIN_NAME(0, SPI2_FS1),
+ UPBOARD_UP2_PIN_NAME(0, SPI2_FS0),
+ UPBOARD_UP2_PIN_NAME(0, SPI2_CLK),
+ UPBOARD_UP2_PIN_NAME(0, SPI1_TXD),
+ UPBOARD_UP2_PIN_NAME(1, SPI1_RXD),
+ UPBOARD_UP2_PIN_NAME(1, SPI1_FS1),
+ UPBOARD_UP2_PIN_NAME(1, SPI1_FS0),
+ UPBOARD_UP2_PIN_NAME(1, SPI1_CLK),
+ UPBOARD_UP2_PIN_ANON(1, 4),
+ UPBOARD_UP2_PIN_ANON(1, 5),
+ UPBOARD_UP2_PIN_ANON(1, 6),
+ UPBOARD_UP2_PIN_ANON(1, 7),
+ UPBOARD_UP2_PIN_NAME(1, PWM1),
+ UPBOARD_UP2_PIN_NAME(1, PWM0),
+ UPBOARD_UP2_PIN_NAME(1, EXHAT_LVDS0n),
+ UPBOARD_UP2_PIN_NAME(1, EXHAT_LVDS0p),
+ UPBOARD_UP2_PIN_FUNC(1, I2C0_SCL, &upboard_i2c0_reg),
+ UPBOARD_UP2_PIN_FUNC(1, I2C0_SDA, &upboard_i2c0_reg),
+ UPBOARD_UP2_PIN_FUNC(1, I2C1_SCL, &upboard_i2c1_reg),
+ UPBOARD_UP2_PIN_FUNC(1, I2C1_SDA, &upboard_i2c1_reg),
+ UPBOARD_UP2_PIN_NAME(2, EXHAT_LVDS3n),
+ UPBOARD_UP2_PIN_NAME(2, EXHAT_LVDS3p),
+ UPBOARD_UP2_PIN_NAME(2, EXHAT_LVDS4n),
+ UPBOARD_UP2_PIN_NAME(2, EXHAT_LVDS4p),
+ UPBOARD_UP2_PIN_NAME(2, EXHAT_LVDS5n),
+ UPBOARD_UP2_PIN_NAME(2, EXHAT_LVDS5p),
+ UPBOARD_UP2_PIN_NAME(2, I2S_SDO),
+ UPBOARD_UP2_PIN_NAME(2, I2S_SDI),
+ UPBOARD_UP2_PIN_NAME(2, I2S_WS_SYNC),
+ UPBOARD_UP2_PIN_NAME(2, I2S_BCLK),
+ UPBOARD_UP2_PIN_NAME(2, EXHAT_LVDS6n),
+ UPBOARD_UP2_PIN_NAME(2, EXHAT_LVDS6p),
+ UPBOARD_UP2_PIN_NAME(2, EXHAT_LVDS7n),
+ UPBOARD_UP2_PIN_NAME(2, EXHAT_LVDS7p),
+ UPBOARD_UP2_PIN_NAME(2, EXHAT_LVDS2n),
+ UPBOARD_UP2_PIN_NAME(2, EXHAT_LVDS2p),
+};
+
+static const unsigned int upboard_up2_rpi_mapping[] = {
+ UPBOARD_UP2_BIT_TO_PIN(1, I2C0_SDA),
+ UPBOARD_UP2_BIT_TO_PIN(1, I2C0_SCL),
+ UPBOARD_UP2_BIT_TO_PIN(1, I2C1_SDA),
+ UPBOARD_UP2_BIT_TO_PIN(1, I2C1_SCL),
+ UPBOARD_UP2_BIT_TO_PIN(0, GPIO3),
+ UPBOARD_UP2_BIT_TO_PIN(0, GPIO11),
+ UPBOARD_UP2_BIT_TO_PIN(0, SPI2_CLK),
+ UPBOARD_UP2_BIT_TO_PIN(1, SPI1_FS1),
+ UPBOARD_UP2_BIT_TO_PIN(1, SPI1_FS0),
+ UPBOARD_UP2_BIT_TO_PIN(1, SPI1_RXD),
+ UPBOARD_UP2_BIT_TO_PIN(0, SPI1_TXD),
+ UPBOARD_UP2_BIT_TO_PIN(1, SPI1_CLK),
+ UPBOARD_UP2_BIT_TO_PIN(1, PWM0),
+ UPBOARD_UP2_BIT_TO_PIN(1, PWM1),
+ UPBOARD_UP2_BIT_TO_PIN(0, UART1_TXD),
+ UPBOARD_UP2_BIT_TO_PIN(0, UART1_RXD),
+ UPBOARD_UP2_BIT_TO_PIN(0, UART1_CTS),
+ UPBOARD_UP2_BIT_TO_PIN(0, UART1_RTS),
+ UPBOARD_UP2_BIT_TO_PIN(2, I2S_BCLK),
+ UPBOARD_UP2_BIT_TO_PIN(2, I2S_WS_SYNC),
+ UPBOARD_UP2_BIT_TO_PIN(2, I2S_SDI),
+ UPBOARD_UP2_BIT_TO_PIN(2, I2S_SDO),
+ UPBOARD_UP2_BIT_TO_PIN(0, GPIO6),
+ UPBOARD_UP2_BIT_TO_PIN(0, SPI2_FS1),
+ UPBOARD_UP2_BIT_TO_PIN(0, SPI2_RXD),
+ UPBOARD_UP2_BIT_TO_PIN(0, SPI2_TXD),
+ UPBOARD_UP2_BIT_TO_PIN(0, SPI2_FS0),
+ UPBOARD_UP2_BIT_TO_PIN(0, GPIO5),
+};
+
+/*
+ * UP Core board + CREX carrier board data
+ */
+
+#define UPBOARD_UPCORE_CREX_BIT_TO_PIN(r, id) \
+ (UPBOARD_BIT_TO_PIN(r, UPFPGA_UPCORE_CREX_##id))
+
+#define UPBOARD_UPCORE_CREX_PIN_ANON(r, bit) \
+ { \
+ .number = UPBOARD_BIT_TO_PIN(r, bit), \
+ }
+
+#define UPBOARD_UPCORE_CREX_PIN_NAME(r, id) \
+ { \
+ .number = UPBOARD_UPCORE_CREX_BIT_TO_PIN(r, id), \
+ .name = #id, \
+ }
+
+#define UPBOARD_UPCORE_CREX_PIN_FUNC(r, id, data) \
+ { \
+ .number = UPBOARD_UPCORE_CREX_BIT_TO_PIN(r, id), \
+ .name = #id, \
+ .drv_data = (void *)(data), \
+ }
+
+enum upboard_upcore_crex_reg1_fpgabit {
+ UPFPGA_UPCORE_CREX_I2C0_SDA,
+ UPFPGA_UPCORE_CREX_I2C0_SCL,
+ UPFPGA_UPCORE_CREX_I2C1_SDA,
+ UPFPGA_UPCORE_CREX_I2C1_SCL,
+ UPFPGA_UPCORE_CREX_SPI2_CS0,
+ UPFPGA_UPCORE_CREX_SPI2_CS1,
+ UPFPGA_UPCORE_CREX_SPI2_MOSI,
+ UPFPGA_UPCORE_CREX_SPI2_MISO,
+ UPFPGA_UPCORE_CREX_SPI2_CLK,
+ UPFPGA_UPCORE_CREX_UART1_TXD,
+ UPFPGA_UPCORE_CREX_UART1_RXD,
+ UPFPGA_UPCORE_CREX_PWM0,
+ UPFPGA_UPCORE_CREX_PWM1,
+ UPFPGA_UPCORE_CREX_I2S2_FRM,
+ UPFPGA_UPCORE_CREX_I2S2_CLK,
+ UPFPGA_UPCORE_CREX_I2S2_RX,
+};
+
+enum upboard_upcore_crex_reg2_fpgabit {
+ UPFPGA_UPCORE_CREX_I2S2_TX,
+ UPFPGA_UPCORE_CREX_GPIO0,
+ UPFPGA_UPCORE_CREX_GPIO2,
+ UPFPGA_UPCORE_CREX_GPIO3,
+ UPFPGA_UPCORE_CREX_GPIO4,
+ UPFPGA_UPCORE_CREX_GPIO9,
+};
+
+static struct pinctrl_pin_desc upboard_upcore_crex_pins[] = {
+ UPBOARD_UPCORE_CREX_PIN_FUNC(0, I2C0_SDA, &upboard_i2c0_reg),
+ UPBOARD_UPCORE_CREX_PIN_FUNC(0, I2C0_SCL, &upboard_i2c0_reg),
+ UPBOARD_UPCORE_CREX_PIN_FUNC(0, I2C1_SDA, &upboard_i2c1_reg),
+ UPBOARD_UPCORE_CREX_PIN_FUNC(0, I2C1_SCL, &upboard_i2c1_reg),
+ UPBOARD_UPCORE_CREX_PIN_NAME(0, SPI2_CS0),
+ UPBOARD_UPCORE_CREX_PIN_NAME(0, SPI2_CS1),
+ UPBOARD_UPCORE_CREX_PIN_NAME(0, SPI2_MOSI),
+ UPBOARD_UPCORE_CREX_PIN_NAME(0, SPI2_MISO),
+ UPBOARD_UPCORE_CREX_PIN_NAME(0, SPI2_CLK),
+ UPBOARD_UPCORE_CREX_PIN_NAME(0, UART1_TXD),
+ UPBOARD_UPCORE_CREX_PIN_NAME(0, UART1_RXD),
+ UPBOARD_UPCORE_CREX_PIN_NAME(0, PWM0),
+ UPBOARD_UPCORE_CREX_PIN_NAME(0, PWM1),
+ UPBOARD_UPCORE_CREX_PIN_NAME(0, I2S2_FRM),
+ UPBOARD_UPCORE_CREX_PIN_NAME(0, I2S2_CLK),
+ UPBOARD_UPCORE_CREX_PIN_NAME(0, I2S2_RX),
+ /* register 1 */
+ UPBOARD_UPCORE_CREX_PIN_NAME(1, I2S2_TX),
+ UPBOARD_UPCORE_CREX_PIN_NAME(1, GPIO0),
+ UPBOARD_UPCORE_CREX_PIN_FUNC(1, GPIO2, &upboard_adc0_reg),
+ UPBOARD_UPCORE_CREX_PIN_NAME(1, GPIO3),
+ UPBOARD_UPCORE_CREX_PIN_NAME(1, GPIO4),
+ UPBOARD_UPCORE_CREX_PIN_NAME(1, GPIO9),
+};
+
+static unsigned int upboard_upcore_crex_rpi_mapping[] = {
+ UPBOARD_UPCORE_CREX_BIT_TO_PIN(0, I2C0_SDA),
+ UPBOARD_UPCORE_CREX_BIT_TO_PIN(0, I2C0_SCL),
+ UPBOARD_UPCORE_CREX_BIT_TO_PIN(0, I2C1_SDA),
+ UPBOARD_UPCORE_CREX_BIT_TO_PIN(0, I2C1_SCL),
+ UPBOARD_UPCORE_CREX_BIT_TO_PIN(1, GPIO0),
+ UPBOARD_UPCORE_CREX_BIT_TO_PIN(1, GPIO2),
+ UPBOARD_UPCORE_CREX_BIT_TO_PIN(1, GPIO3),
+ UPBOARD_UPCORE_CREX_BIT_TO_PIN(0, SPI2_CS1),
+ UPBOARD_UPCORE_CREX_BIT_TO_PIN(0, SPI2_CS0),
+ UPBOARD_UPCORE_CREX_BIT_TO_PIN(0, SPI2_MISO),
+ UPBOARD_UPCORE_CREX_BIT_TO_PIN(0, SPI2_MOSI),
+ UPBOARD_UPCORE_CREX_BIT_TO_PIN(0, SPI2_CLK),
+ UPBOARD_UPCORE_CREX_BIT_TO_PIN(0, PWM0),
+ UPBOARD_UPCORE_CREX_BIT_TO_PIN(0, PWM1),
+ UPBOARD_UPCORE_CREX_BIT_TO_PIN(0, UART1_TXD),
+ UPBOARD_UPCORE_CREX_BIT_TO_PIN(0, UART1_RXD),
+ UPBOARD_UPCORE_CREX_BIT_TO_PIN(1, GPIO9),
+ UPBOARD_UPCORE_CREX_BIT_TO_PIN(1, GPIO4),
+ UPBOARD_UPCORE_CREX_BIT_TO_PIN(0, I2S2_CLK),
+ UPBOARD_UPCORE_CREX_BIT_TO_PIN(0, I2S2_FRM),
+ UPBOARD_UPCORE_CREX_BIT_TO_PIN(0, I2S2_RX),
+ UPBOARD_UPCORE_CREX_BIT_TO_PIN(1, I2S2_TX),
+};
+
+/*
+ * UP Core board + CRST02 carrier board data
+ */
+
+#define upboard_upcore_crst02_pins upboard_upcore_crex_pins
+#define upboard_upcore_crst02_rpi_mapping upboard_upcore_crex_rpi_mapping
+
+static int upboard_set_mux(struct pinctrl_dev *pctldev, unsigned int function,
+ unsigned int group)
+{
+ return 0;
+}
+
+static int upboard_fpga_request_enable(struct pinctrl_dev *pctldev,
+ struct pinctrl_gpio_range *range,
+ unsigned int pin)
+{
+ const struct pin_desc * const pd = pin_desc_get(pctldev, pin);
+ const struct upboard_pin *p;
+ int ret;
+
+ p = pd->drv_data;
+ if (p->funcbit) {
+ ret = regmap_field_write(p->funcbit, 0);
+ if (ret)
+ return ret;
+ }
+
+ if (p->enbit) {
+ ret = regmap_field_write(p->enbit, 1);
+ if (ret)
+ return ret;
+ }
+
+ return 0;
+}
+
+static int upboard_fpga_request_free(struct pinctrl_dev *pctldev,
+ unsigned int pin)
+{
+ const struct pin_desc * const pd = pin_desc_get(pctldev, pin);
+ const struct upboard_pin *p;
+ int ret;
+
+ p = pd->drv_data;
+ if (p->funcbit) {
+ ret = regmap_field_write(p->funcbit, 1);
+ if (ret)
+ return ret;
+ }
+
+ if (p->enbit) {
+ ret = regmap_field_write(p->enbit, 0);
+ if (ret)
+ return ret;
+ }
+
+ return 0;
+}
+
+static int upboard_fpga_set_direction(struct pinctrl_dev *pctldev,
+ struct pinctrl_gpio_range *range,
+ unsigned int pin, bool input)
+{
+ const struct pin_desc * const pd = pin_desc_get(pctldev, pin);
+ const struct upboard_pin *p;
+
+ p = pd->drv_data;
+ upboard_fpga_request_enable(pctldev, range, pin);
+
+ return regmap_field_write(p->dirbit, input);
+}
+
+static int upboard_get_functions_count(struct pinctrl_dev *pctldev)
+{
+ return 0;
+}
+
+static const char *upboard_get_function_name(struct pinctrl_dev *pctldev,
+ unsigned int selector)
+{
+ return NULL;
+}
+
+static int upboard_get_function_groups(struct pinctrl_dev *pctldev,
+ unsigned int selector,
+ const char * const **groups,
+ unsigned int *num_groups)
+{
+ *groups = NULL;
+ *num_groups = 0;
+ return 0;
+}
+
+static const struct pinmux_ops upboard_pinmux_ops = {
+ .get_functions_count = upboard_get_functions_count,
+ .get_function_groups = upboard_get_function_groups,
+ .get_function_name = upboard_get_function_name,
+ .set_mux = upboard_set_mux,
+ .gpio_request_enable = upboard_fpga_request_enable,
+ .gpio_set_direction = upboard_fpga_set_direction,
+};
+
+static int upboard_get_groups_count(struct pinctrl_dev *pctldev)
+{
+ return 0;
+}
+
+static const char *upboard_get_group_name(struct pinctrl_dev *pctldev,
+ unsigned int selector)
+{
+ return NULL;
+}
+
+static const struct pinctrl_ops upboard_pinctrl_ops = {
+ .get_groups_count = upboard_get_groups_count,
+ .get_group_name = upboard_get_group_name,
+};
+
+static struct pinctrl_desc upboard_up_pinctrl_desc = {
+ .pins = upboard_up_pins,
+ .npins = ARRAY_SIZE(upboard_up_pins),
+ .pctlops = &upboard_pinctrl_ops,
+ .pmxops = &upboard_pinmux_ops,
+ .owner = THIS_MODULE,
+};
+
+static struct pinctrl_desc upboard_up2_pinctrl_desc = {
+ .pins = upboard_up2_pins,
+ .npins = ARRAY_SIZE(upboard_up2_pins),
+ .pctlops = &upboard_pinctrl_ops,
+ .pmxops = &upboard_pinmux_ops,
+ .owner = THIS_MODULE,
+};
+
+static struct pinctrl_desc upboard_upcore_crex_pinctrl_desc = {
+ .pins = upboard_upcore_crex_pins,
+ .npins = ARRAY_SIZE(upboard_upcore_crex_pins),
+ .pctlops = &upboard_pinctrl_ops,
+ .pmxops = &upboard_pinmux_ops,
+ .owner = THIS_MODULE,
+};
+
+static struct pinctrl_desc upboard_upcore_crst02_pinctrl_desc = {
+ .pins = upboard_upcore_crst02_pins,
+ .npins = ARRAY_SIZE(upboard_upcore_crst02_pins),
+ .pctlops = &upboard_pinctrl_ops,
+ .pmxops = &upboard_pinmux_ops,
+ .owner = THIS_MODULE,
+};
+
+static int upboard_alt_func_enable(struct gpio_chip *gc, const char *name, int id)
+{
+ struct upboard_pinctrl *pctrl = container_of(gc, struct upboard_pinctrl, chip);
+ int *offset;
+ int i, cnt;
+
+ offset = kmalloc(pctrl->pctldesc->npins * sizeof(int), GFP_KERNEL);
+ if (!offset)
+ return -ENOMEM;
+
+ /* find all pins */
+ for (i = 0, cnt = 0; i < pctrl->pctldesc->npins; i++) {
+ if (strstr(pctrl->pctldesc->pins[i].name, name))
+ offset[cnt++] = i;
+ }
+
+ for (i = 0; i < cnt; i++) {
+ if (pinctrl_gpio_request(pctrl->pins[offset[i]].gpio))
+ return 0; /* this pin is being used */
+
+ pinctrl_gpio_free(pctrl->pins[offset[i]].gpio);
+ }
+
+ /* change to alternate function */
+ for (i = 0; i < cnt; i++) {
+ if (pctrl->pins[offset[i]].regs == NULL)
+ continue;
+ bool input = false;
+ int mode = 1; /* default */
+ unsigned int val = readl(pctrl->pins[offset[i]].regs);
+
+ if (strstr(pctrl->pctldesc->pins[offset[i]].name, "I2C")) {
+ switch (id) {
+ case BOARD_UPN_ADLN01:
+ case BOARD_UPX_ADLP01:
+ mode = 2;
+ break;
+ default:
+ break;
+ }
+ val |= mode<<PADCFG0_PMODE_SHIFT;
+ writel(val, pctrl->pins[offset[i]].regs);
+ upboard_fpga_request_free(pctrl->pctldev, offset[i]);
+ continue;
+ } else if (strstr(pctrl->pctldesc->pins[offset[i]].name, "UART")) {
+ switch (id) {
+ case BOARD_UPN_EHL01:
+ case BOARD_UPS_EHL01:
+ mode = 4;
+ break;
+ case BOARD_UPN_ADLN01:
+ case BOARD_UPX_ADLP01:
+ mode = 2;
+ break;
+ default:
+ break;
+ }
+ } else if (strstr(pctrl->pctldesc->pins[offset[i]].name, "SPI")) {
+ switch (id) {
+ case BOARD_UP_WHL01:
+ mode = 3;
+ break;
+ case BOARD_UPN_ADLN01:
+ case BOARD_UPX_ADLP01:
+ mode = 7;
+ if (strstr(pctrl->pctldesc->pins[offset[i]].name, "MOSI")) {
+ val &= ~PADCFG0_GPIOTXDIS;
+ val |= PADCFG0_GPIORXDIS;
+ }
+ if (strstr(pctrl->pctldesc->pins[offset[i]].name, "MISO")) {
+ val |= PADCFG0_GPIORXDIS;
+ }
+ if (strstr(pctrl->pctldesc->pins[offset[i]].name, "CLK")) {
+ val &= ~PADCFG0_GPIOTXDIS;
+ val |= PADCFG0_GPIORXDIS;
+ }
+ if (strstr(pctrl->pctldesc->pins[offset[i]].name, "CS0")) {
+ val |= PADCFG0_GPIORXDIS;
+ }
+ if (strstr(pctrl->pctldesc->pins[offset[i]].name, "CS1")) {
+ continue;
+ }
+ break;
+ default:
+ break;
+ }
+ } else if (strstr(pctrl->pctldesc->pins[offset[i]].name, "I2S")) {
+ switch (id) {
+ case BOARD_UPX_ADLP01:
+ mode = 4;
+ break;
+ default:
+ break;
+ }
+ }
+ val |= mode<<PADCFG0_PMODE_SHIFT;
+ writel(val, pctrl->pins[offset[i]].regs);
+
+ /* input pins */
+ if (strstr(pctrl->pctldesc->pins[offset[i]].name, "RX"))
+ input = true;
+ if (strstr(pctrl->pctldesc->pins[offset[i]].name, "CTS"))
+ input = true;
+ if (strstr(pctrl->pctldesc->pins[offset[i]].name, "ADC"))
+ input = true;
+ if (strstr(pctrl->pctldesc->pins[offset[i]].name, "MISO"))
+ input = true;
+ if (strstr(pctrl->pctldesc->pins[offset[i]].name, "DIN"))
+ input = true;
+ if (strstr(pctrl->pctldesc->pins[offset[i]].name, "SDI"))
+ input = true;
+ upboard_fpga_set_direction(pctrl->pctldev, NULL, offset[i], input);
+ }
+
+ kfree(offset);
+
+ return 0;
+}
+
+static int upboard_rpi_to_native_gpio(struct gpio_chip *gc, unsigned int gpio)
+{
+ struct upboard_pinctrl *pctrl = container_of(gc, struct upboard_pinctrl, chip);
+ unsigned int pin = pctrl->rpi_mapping[gpio];
+ struct pinctrl_gpio_range *range;
+
+ range = pinctrl_find_gpio_range_from_pin(pctrl->pctldev, pin);
+ if (!range)
+ return -ENODEV;
+
+ return range->base;
+}
+
+static int upboard_gpio_request(struct gpio_chip *gc, unsigned int offset)
+{
+ int gpio = upboard_rpi_to_native_gpio(gc, offset);
+
+ return pinctrl_gpio_request(gpio);
+}
+
+static void upboard_gpio_free(struct gpio_chip *gc, unsigned int offset)
+{
+ struct upboard_pinctrl *pctrl = container_of(gc, struct upboard_pinctrl, chip);
+ int gpio = upboard_rpi_to_native_gpio(gc, offset);
+ unsigned int pin = pctrl->rpi_mapping[offset];
+ char *name;
+ char *p;
+
+ name = kmalloc(strlen(pctrl->pctldesc->pins[pin].name) + 1, GFP_KERNEL);
+ if (!name) {
+ dev_err(gc->parent, "Failed to kmalloc");
+ return;
+ }
+ pinctrl_gpio_free(gpio);
+
+ strcpy(name, pctrl->pctldesc->pins[pin].name);
+ p = name;
+ upboard_alt_func_enable(gc, strsep(&p, "_"), pctrl->ident);
+
+ kfree(name);
+}
+
+static int upboard_gpio_get(struct gpio_chip *gc, unsigned int offset)
+{
+ int gpio = upboard_rpi_to_native_gpio(gc, offset);
+
+ return gpiod_get_value(gpio_to_desc(gpio));
+}
+
+static void upboard_gpio_set(struct gpio_chip *gc, unsigned int offset,
+ int value)
+{
+ struct upboard_pinctrl *pctrl = container_of(gc, struct upboard_pinctrl, chip);
+ unsigned int pin = pctrl->rpi_mapping[offset];
+ int gpio = upboard_rpi_to_native_gpio(gc, offset);
+
+ gpiod_set_value(gpio_to_desc(gpio), value);
+
+ /* APL03 board open drain GPIO */
+ if (pctrl->ident == BOARD_UP_APL03) {
+ if (pin == 0 || pin == 1) {
+ int val = readl(pctrl->pins[pin].regs);
+
+ if (value)
+ val |= PADCFG0_GPIOTXDIS;
+ else
+ val &= ~PADCFG0_GPIOTXDIS;
+
+ writel(val, pctrl->pins[pin].regs);
+ }
+ }
+}
+
+static int upboard_gpio_direction_input(struct gpio_chip *gc,
+ unsigned int offset)
+{
+ int gpio = upboard_rpi_to_native_gpio(gc, offset);
+ struct upboard_pinctrl *pctrl = container_of(gc, struct upboard_pinctrl, chip);
+ unsigned int pin = pctrl->rpi_mapping[offset];
+ struct pinctrl_gpio_range *range;
+
+ range = pinctrl_find_gpio_range_from_pin(pctrl->pctldev, pin);
+ upboard_fpga_set_direction(pctrl->pctldev, range, pin, true);
+
+ return gpiod_direction_input(gpio_to_desc(gpio));
+}
+
+static int upboard_gpio_direction_output(struct gpio_chip *gc,
+ unsigned int offset, int value)
+{
+ int gpio = upboard_rpi_to_native_gpio(gc, offset);
+ struct upboard_pinctrl *pctrl = container_of(gc, struct upboard_pinctrl, chip);
+ unsigned int pin = pctrl->rpi_mapping[offset];
+ struct pinctrl_gpio_range *range;
+
+ range = pinctrl_find_gpio_range_from_pin(pctrl->pctldev, pin);
+ upboard_fpga_set_direction(pctrl->pctldev, range, pin, false);
+
+ return gpiod_direction_output(gpio_to_desc(gpio), value);
+}
+
+static void __iomem *upboard_get_regs(struct gpio_chip *gc, unsigned int gpio, unsigned int reg)
+{
+ struct platform_device *pdev = to_platform_device(gc->parent);
+ struct resource *res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+ struct intel_pinctrl *pctrl = gpiochip_get_data(gc);
+ size_t nregs;
+ void __iomem *base = NULL;
+ u32 offset, value;
+ int pin = gpio-gc->base;
+
+ /* check Intel pin controller for all platform */
+ if (pctrl->ncommunities > 1) {
+ int i, j, offset = 0;
+
+ pin = -1;
+ for (i = 0; i < pctrl->ncommunities; i++) {
+ struct intel_community *community = &pctrl->communities[i];
+
+ for (j = 0; j < community->ngpps ; j++) {
+ struct intel_padgroup gpps = community->gpps[j];
+
+ if (gpio < gc->base + gpps.gpio_base + gpps.size) {
+ res = platform_get_resource(pdev, IORESOURCE_MEM,
+ community->barno);
+ pin = gpio-gc->base-gpps.gpio_base +
+ offset-community->pin_base;
+ break;
+ }
+
+ offset += gpps.size;
+ }
+
+ if (pin != -1)
+ break;
+ }
+ }
+
+ base = devm_ioremap(&pdev->dev, res->start, resource_size(res));
+ if (base == NULL)
+ return base;
+
+ offset = readl(base + PADBAR);
+ value = readl(base + REVID);
+
+ if (((value & REVID_MASK) >> REVID_SHIFT) >= 0x94)
+ nregs = 4;
+ else
+ nregs = 2;
+
+ return base + offset + reg + pin * nregs * 4;
+}
+
+static int upboard_acpi_node_pin_mapping(struct upboard_fpga *fpga,
+ struct upboard_pinctrl *pctrl,
+ const char *propname,
+ const char *pinctl_name,
+ unsigned int pin_offset)
+{
+ struct gpio_descs *descs;
+ int ret, i;
+
+ descs = devm_gpiod_get_array(fpga->dev, propname, GPIOD_ASIS);
+ if (IS_ERR(descs)) {
+ ret = PTR_ERR(descs);
+ if (ret != -EPROBE_DEFER)
+ dev_err(fpga->dev, "Failed to get %s gpios", propname);
+
+ return ret;
+ }
+
+ for (i = 0; i < descs->ndescs; i++) {
+ struct gpio_desc *desc = descs->desc[i];
+ struct gpio_chip *gc = gpiod_to_chip(desc);
+
+ pctrl->pins[i].gpio = desc_to_gpio(desc);
+ pctrl->pins[i].base = gc->base;
+ pctrl->pins[i].irq = gpiod_to_irq(desc);
+ pctrl->pins[i].regs =
+ upboard_get_regs(gc,
+ desc_to_gpio(desc) - gc->base,
+ PADCFG0);
+
+ /* The GPIOs may not be contiguous, so add them 1-by-1 */
+ ret = gpiochip_add_pin_range(gpiod_to_chip(desc), pinctl_name,
+ desc_to_gpio(desc) - gc->base,
+ pin_offset + i, 1);
+ if (ret)
+ return ret;
+ }
+
+ /* dispose acpi resource */
+ devm_gpiod_put_array(fpga->dev, descs);
+
+ return ret;
+}
+
+static struct gpio_chip upboard_gpio_chip = {
+ .label = "Raspberry Pi compatible UP GPIO",
+ .base = 0,
+ .request = upboard_gpio_request,
+ .free = upboard_gpio_free,
+ .get = upboard_gpio_get,
+ .set = upboard_gpio_set,
+ .direction_input = upboard_gpio_direction_input,
+ .direction_output = upboard_gpio_direction_output,
+ .owner = THIS_MODULE,
+};
+
+/* DMI Matches for older bios without fpga initialization */
+static const struct dmi_system_id upboard_dmi_table[] __initconst = {
+ {
+ .ident = (const char *) BOARD_UP_APL03,
+ .matches = { /* UP 4000 */
+ DMI_EXACT_MATCH(DMI_SYS_VENDOR, "AAEON"),
+ DMI_EXACT_MATCH(DMI_BOARD_NAME, "UP-APL03"),
+ },
+ },
+ {
+ .ident = (const char *) BOARD_UP_WHL01,
+ .matches = { /* UPX WHL */
+ DMI_EXACT_MATCH(DMI_SYS_VENDOR, "AAEON"),
+ DMI_EXACT_MATCH(DMI_BOARD_NAME, "UP-WHL01"),
+ },
+ },
+ {
+ .ident = (const char *) BOARD_UPX_TGL,
+ .matches = { /* UP i11 */
+ DMI_EXACT_MATCH(DMI_SYS_VENDOR, "AAEON"),
+ DMI_EXACT_MATCH(DMI_BOARD_NAME, "UPX-TGL01"),
+ },
+ },
+ {
+ .ident = (const char *) BOARD_UPN_EHL01,
+ .matches = { /* UP 6000 */
+ DMI_EXACT_MATCH(DMI_SYS_VENDOR, "AAEON"),
+ DMI_EXACT_MATCH(DMI_BOARD_NAME, "UPN-EHL01"),
+ },
+ },
+ {
+ .ident = (const char *) BOARD_UPS_EHL01,
+ .matches = { /* UP squared v2 */
+ DMI_EXACT_MATCH(DMI_SYS_VENDOR, "AAEON"),
+ DMI_EXACT_MATCH(DMI_BOARD_NAME, "UPS-EHL01"),
+ },
+ },
+ {
+ .ident = (const char *) BOARD_UPX_ADLP01,
+ .matches = { /* UP Xtreme i12 */
+ DMI_EXACT_MATCH(DMI_SYS_VENDOR, "AAEON"),
+ DMI_EXACT_MATCH(DMI_BOARD_NAME, "UPX-ADLP01"),
+ },
+ },
+ {
+ .ident = (const char *) BOARD_UPN_ADLN01,
+ .matches = { /* UP 7000 */
+ DMI_EXACT_MATCH(DMI_SYS_VENDOR, "AAEON"),
+ DMI_EXACT_MATCH(DMI_BOARD_NAME, "UPN-ADLN01"),
+ },
+ },
+ {
+ .ident = (const char *) BOARD_UPS_ADLP01,
+ .matches = { /* UP Squared i12 */
+ DMI_EXACT_MATCH(DMI_SYS_VENDOR, "AAEON"),
+ DMI_EXACT_MATCH(DMI_BOARD_NAME, "UPS-ADLP01"),
+ },
+ },
+ { } /* Terminating entry */
+};
+
+static int __init upboard_pinctrl_probe(struct platform_device *pdev)
+{
+ struct upboard_fpga * const fpga = dev_get_drvdata(pdev->dev.parent);
+ struct acpi_device * const adev = ACPI_COMPANION(&pdev->dev);
+ struct pinctrl_desc *pctldesc;
+ struct upboard_pinctrl *pctrl;
+ struct upboard_pin *pins;
+ const struct dmi_system_id *system_id;
+ const char *hid;
+ const unsigned int *rpi_mapping;
+ unsigned int ngpio;
+ int ret;
+ int i;
+
+ if (!fpga)
+ return -EINVAL;
+
+ if (!adev)
+ return -ENODEV;
+
+ /* set pin desc and rpi GPIO mapping table by HID */
+ hid = acpi_device_hid(adev);
+ if (!strcmp(hid, "AANT0F00") || !strcmp(hid, "AANT0F04") ||
+ !strcmp(hid, "AANT0000")) {
+ pctldesc = &upboard_up_pinctrl_desc;
+ rpi_mapping = upboard_up_rpi_mapping;
+ ngpio = ARRAY_SIZE(upboard_up_rpi_mapping);
+ } else if (!strcmp(hid, "AANT0F01")) {
+ pctldesc = &upboard_up2_pinctrl_desc;
+ rpi_mapping = upboard_up2_rpi_mapping;
+ ngpio = ARRAY_SIZE(upboard_up2_rpi_mapping);
+ } else if (!strcmp(hid, "AANT0F02")) {
+ pctldesc = &upboard_upcore_crex_pinctrl_desc;
+ rpi_mapping = upboard_upcore_crex_rpi_mapping;
+ ngpio = ARRAY_SIZE(upboard_upcore_crex_rpi_mapping);
+ } else if (!strcmp(hid, "AANT0F03")) {
+ pctldesc = &upboard_upcore_crst02_pinctrl_desc;
+ rpi_mapping = upboard_upcore_crst02_rpi_mapping;
+ ngpio = ARRAY_SIZE(upboard_upcore_crst02_rpi_mapping);
+ } else
+ return -ENODEV;
+
+ pctldesc->name = dev_name(&pdev->dev);
+
+ pins = devm_kcalloc(&pdev->dev, pctldesc->npins, sizeof(*pins), GFP_KERNEL);
+ if (!pins)
+ return -ENOMEM;
+
+ /* initialise pins */
+ for (i = 0; i < pctldesc->npins; i++) {
+ struct upboard_pin *pin = &pins[i];
+ struct pinctrl_pin_desc *pd = (struct pinctrl_pin_desc *) &pctldesc->pins[i];
+ struct reg_field fldconf = {0};
+ unsigned int regoff = (pd->number / UPFPGA_REGISTER_SIZE);
+ unsigned int lsb = pd->number % UPFPGA_REGISTER_SIZE;
+
+ pin->funcbit = NULL;
+
+ if (pd->drv_data) {
+ fldconf = *(struct reg_field *)pd->drv_data;
+
+ pin->funcbit = devm_regmap_field_alloc(&pdev->dev,
+ fpga->regmap,
+ fldconf);
+ if (IS_ERR(pin->funcbit))
+ return PTR_ERR(pin->funcbit);
+ }
+
+ pin->enbit = NULL;
+ fldconf.reg = UPFPGA_REG_GPIO_EN0 + regoff;
+ fldconf.lsb = lsb;
+ fldconf.msb = lsb;
+
+ pin->enbit = devm_regmap_field_alloc(&pdev->dev,
+ fpga->regmap,
+ fldconf);
+ if (IS_ERR(pin->enbit))
+ return PTR_ERR(pin->enbit);
+
+ fldconf.reg = UPFPGA_REG_GPIO_DIR0 + regoff;
+ fldconf.lsb = lsb;
+ fldconf.msb = lsb;
+
+ pin->dirbit = devm_regmap_field_alloc(&pdev->dev,
+ fpga->regmap,
+ fldconf);
+ if (IS_ERR(pin->dirbit))
+ return PTR_ERR(pin->dirbit);
+
+ pd->drv_data = pin;
+
+ /* set output by default */
+ regmap_field_write(pin->dirbit, false);
+ }
+
+ /* create a new pinctrl device and register it */
+ pctrl = devm_kzalloc(&pdev->dev, sizeof(*pctrl), GFP_KERNEL);
+ if (!pctrl)
+ return -ENOMEM;
+
+ pctrl->regmap = fpga->regmap;
+ pctrl->rpi_mapping = rpi_mapping;
+ pctrl->chip = upboard_gpio_chip;
+ pctrl->pctldesc = pctldesc;
+ pctrl->chip.parent = &pdev->dev;
+ pctrl->chip.ngpio = ngpio;
+ pctrl->pins = pins;
+
+ ret = devm_gpiochip_add_data(&pdev->dev, &pctrl->chip, pctrl);
+ if (ret)
+ return ret;
+
+ pctrl->pctldev = devm_pinctrl_register(&pdev->dev, pctldesc, pctrl);
+ if (IS_ERR(pctrl->pctldev))
+ return PTR_ERR(pctrl->pctldev);
+
+ /* add acpi pin mapping according to external-gpios key */
+ ret = upboard_acpi_node_pin_mapping(fpga, pctrl,
+ "external",
+ dev_name(&pdev->dev),
+ 0);
+ if (ret)
+ return ret;
+
+ /* check for special board versions that require register patches */
+ system_id = dmi_first_match(upboard_dmi_table);
+ if (system_id)
+ pctrl->ident = (int) system_id->ident;
+ else
+ pctrl->ident = BOARD_UP_APL03;
+
+ upboard_alt_func_enable(&pctrl->chip, "I2C", pctrl->ident);
+ upboard_alt_func_enable(&pctrl->chip, "SPI", pctrl->ident);
+ upboard_alt_func_enable(&pctrl->chip, "SPI1", pctrl->ident);
+ upboard_alt_func_enable(&pctrl->chip, "SPI2", pctrl->ident);
+ upboard_alt_func_enable(&pctrl->chip, "UART", pctrl->ident);
+ upboard_alt_func_enable(&pctrl->chip, "I2S", pctrl->ident);
+ upboard_alt_func_enable(&pctrl->chip, "PWM", pctrl->ident);
+ upboard_alt_func_enable(&pctrl->chip, "ADC", pctrl->ident);
+ /* I2C pin mux by CPLD in UP2 */
+ upboard_alt_func_enable(&pctrl->chip, "NONAME", pctrl->ident);
+
+ return ret;
+}
+
+static struct platform_driver upboard_pinctrl_driver = {
+ .driver = {
+ .name = "upboard-pinctrl",
+ },
+};
+module_platform_driver_probe(upboard_pinctrl_driver, upboard_pinctrl_probe);
+
+MODULE_AUTHOR("Gary Wang <garywang@aaeon.com.tw>");
+MODULE_DESCRIPTION("UP Board HAT pin controller driver");
+MODULE_LICENSE("GPL v2");
+MODULE_ALIAS("platform:upboard-pinctrl");
--
2.17.1
^ permalink raw reply related [flat|nested] 6+ messages in thread